Click on Series name for product info on aimtec.com Series AMEPR5-AZ up to 1A | AC-DC / DC-DC LED driver FEATURES: AC-DC or DC-DC Constant current LED Driver Input range 90-264VAC/47-440Hz Operating temperature 0 to 80°C High Efficiency up to 79% 5 Years Limited Warranty SCP, Over Voltage Protection Waterproof Case rated IP67 No load consumption <0.3W Models Single output Model Max Output Power (W) ① Output Voltage Range (V) Output Current (A) Input Voltage (VAC/Hz) AMEPR5-1630AZ 4.8 8-16 0.3 90-264/47-440 AMEPR5-1435AZ 4.9 6-14 0.35 90-264/47-440 AMEPR5-1236AZ 4.32 5-12 0.36 90-264/47-440 AMEPR5-0670AZ 4.2 2-6 0.7 90-264/47-440 AMEPR5-05100AZ 5 3-5 1 90-264/47-440 ① Exceeding the maximum output power will permanently damage the converter Input Voltage (VDC) 130-370 130-370 130-370 130-370 130-370 Efficiency (%) 115 230 VAC VAC 79 77 77 76 74 75 74 74 73 72 NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See http://www.aimtec.com/termssale AMEPR5-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Inrush current <2ms Leakage current AC current No load consumption Conditions Typical 115VAC 230VAC 115VAC 230VAC 115VAC 230VAC 115VAC 230VAC 15 30 0.2 0.25 0.09 0.06 0.1 0.2 External fuse Start up time Maximum Units A mA A W 250V/0.5A 140 ms Output Specifications Parameters Current accuracy Line regulation Load regulation Ripple & Noise ② Conditions Typical LL-HL 0-100% load 6/12/14/16V models 5V model ±10 ±5 ±10 100 150 2 Maximum Units % % % mV p-p Hold-up time Minimum Load Voltage See the models table ② Ripple and Noise are measured at 20MHz bandwidth by using a 0.1μF (M/C) or (C/C) and 220µF (E/C) parallel capacitor. www.aimtec.com F 052.1e R3.L Tel: +1 514 620 2722 1 of 3 ms Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR5-AZ up to 1A | AC-DC / DC-DC LED driver Isolation Specifications Parameters Conditions Tested I/O voltage Isolation Resistance Typical 3sec Maximum Units 3000 VAC MΩ >1000 General Specifications Parameters Conditions Switching frequency Over Load protection Over voltage protection Short circuit protection Operating temperature Maximum case temperature Storage temperature Temperature coefficient Cooling Humidity Case material Potting Wires Weight Dimensions (L X Diameter) MTBF Typical Maximum 65 103 ≥103 Auto recovery 0 to +80 With derating over 50°C KHz % % oC 100 oC oC -40 to +95 ±0.02 Free air convection % / oC 95 Plastic Epoxy (IP67 rated) UL1015 22AWG * 10CM 25 29 x 26.5 mm (1.14x1.04 inch) >400,000 hrs (MIL-HDBK-217F at +25°C) Units % RH g Environment Approval Test Shock Vibration Parameters Wave form Acceleration amplitude Bump duration Converter operation Number of bumps Test mode Displacement Acceleration Converter operation Conditions Half sine wave 5gn 30ms Before and after test, body mounted (on chassis) 18 (3 in each direction for every axis) Sweep sine, 10-100Hz, speed 0.05Hz/s 1 mm 3g, 3 loops 30min one cycle, 3h total, every axis tested Before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals Standards www.aimtec.com F 052.1e R3.L cULus, CE, FCC EN61347-1, EN61347-2-13, IEC62384, UL8750, UL60950-1, EN55015, EN55024, FCC part 15 Subpart B, Class B, ANSI C63.4 :2003 Harmonic Current Emissions IEC/EN 61000-3-2, (EN60555-2) Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 1 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 2 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEPR5-AZ up to 1A | AC-DC / DC-DC LED driver Dimensions Temperature Graph Free Air Convection 50 º C Output Power % 100 80 60 Safe Operating Area 40 20 0 - 20 0 20 40 60 80 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 052.1e R3.L Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only