ETC2 APSA6R3ELL221MF9JG Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
Upgrade!
@Super low ESR, high temperature resistance and high ripple current capability
@Rated voltage range : 2.5 to 16Vdc
@2000 hours at 105C
@Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
@Pb-free design
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105C
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
2.5 to 16Vdc
P20% (M)
Rated voltageB1.15V
I=0.2CV (max.)
Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc)
Dissipation Factor
(tane)
0.08 max.
Low Temperature
Characteristics
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Max. impedance ratio at 100kHz to the 20C value
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 105C.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 1000 hours.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
?MARKING
@Terminal Code : E
FP0.5
EX) 4V560MF
FD+0.5max.
Fd
Coated Case
L+1.5 max.
15min.
4min.
A 292
560
4V
fD
fd
L'
F
(1/2)
6.3
0.5
L+1.0
2.5
8
10
0.8
L+1.5
3.5
5
CAT. No. E1001E
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
Upgrade!
?PART NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PSA AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 270MF:271,1000MF:102)
Lead forming·Taping code
Terminal code
Voltage code (ex. 4V:4R0,6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
?STANDARD RATINGS
WV(Vdc)
2.5
4
6.3
10
16
Cap(mF)
390
680
820
1000
270
390
560
820
220
330
390
680
47
68
100
150
270
470
100
Case size
fDbL(mm)
ESR
(momax/20c, 100k to 300kHz)
Rated ripple current
(mArms/105c, 100kHz)
6.3B9.8
8B11.5
8B11.5
10B11.5
6.3B9.8
6.3B9.8
8B11.5
10B11.5
6.3B9.8
6.3B9.8
8B11.5
10B11.5
6.3B9.8
6.3B9.8
6.3B9.8
6.3B9.8
8B11.5
10B11.5
6.3B9.8
20
7
7
6
20
24
7
6
20
28
8
7
25
25
25
25
9
8
25
3160
5580
5580
5860
3160
3300
5580
5860
3160
3190
5080
5860
2820
2820
2820
2820
4710
5650
2820
Part No.
APSA2R5ESS391MF9JG
APSA2R5ESS681MHB5S
APSA2R5ESS821MHB5S
APSA2R5ESS102MJB5S
APSA4R0ESS271MF9JG
APSA4R0ESS391MF9JG
APSA4R0ESS561MHB5S
APSA4R0ESS821MJB5S
APSA6R3ESS221MF9JG
APSA6R3ESS331MF9JG
APSA6R3ESS391MHB5S
APSA6R3ESS681MJB5S
APSA100ESS470MF9JG
APSA100ESS680MF9JG
APSA100ESS101MF9JG
APSA100ESS151MF9JG
APSA100ESS271MHB5S
APSA100ESS471MJB5S
APSA160ESS101MF9JG
SS : Lead forming code and taping code
(2/2)
CAT. No. E1001E
Similar pages