APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR General Description Features • • • • • • • • 1.3V Maximum Dropout at Full Load Current Fast Transient Response Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection 3-Terminal Adjustable or Fixed 1.8V, 2.5V, 3.3V SOT223-3L and TO252-3L, Packages in “Green” Molding Compound (No Br, Sb) Lead Free Finish / RoHS Compliant (Note 1) APX1117 is a low dropout positive adjustable or fixed-mode voltage regulator with 1A output current capability. The product is specifically designed to provide well-regulated supply for applications such as high-speed bus termination and low current 3.3V logic supply. APX1117 is also well suited for other applications such as VGA cards. APX1117 is guaranteed to have lower than 1.3V dropout at full load current making it ideal to provide well-regulated outputs of 1.25V to 5.0V with 6.3V to 18V input supply. Applications • • PC Peripheral Communication Ordering Information A P X 1 1 1 7 X XX X X Package D : TO252-3L E : SOT223-3L Note: Note: Vout Blank: Adj 18: 1.8V 25: 2.5V 33: 3.3V Lead Free Packing G : Green - U : Tube -13 : Taping 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7. Device Package Code APX1117D APX1117E D E Tube 13” Tape and Reel Part Number Part Number Quantity Quantity Suffix Suffix TO252-3L 80 -U 2500/Tape & Reel -13 SOT223-3L 75 -U 2500/Tape & Reel -13 Packaging (Note 2) 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. APX1117 Rev. 1 1 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Pin Assignments (1) TO252-3L ( Top View ) 3 VIN 2 VOUT Adj (GND) 1 Tab is VOUT (2) SOT223-3L ( T o p V ie w ) 3 V IN 2 V OUT 1 A d j (G N D ) T a b is V O U T Pin Descriptions Name I/O PIN # Adj (GND) I 1 VOUT O 2 VIN I 3 APX1117 Rev. 1 Descripitions A resistor divider from this pin to the VOUT pin and ground sets the output voltage (Ground only for Fixed-Mode). The output of the regulator. A minimum of 10uF capacitor (0.15Ω ≤ ESR ≤ 20Ω) must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor (0.15Ω ≤ ESR ≤ 20Ω) is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than VOUT in order for the device to regulate properly. 2 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Block Diagram 3 VIN 2 VOUT + + - 1.25V + CURRENT LIMIT 1 GND (FIXED) + 1 - Thermal Shutdown Adj Absolute Maximum Ratings Symbol Note: Parameter Rating Unit VIN DC Supply Voltage -0.3 to 18 V TJ Operating Junction Temperature Range 0 to +125 °C TMJ Maximum Junction Temperature 150 °C PD Power Dissipation SOT223-3L TO252-3L Internally limited by maximum junction temperature of 150°C (Note 3) mW TST Storage Temperature -65 to +150 °C 3. APX1117 contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature is exceeded. When activated, typically at 150°C, the regulator output switches off and then back on as the die cools. APX1117 Rev. 1 3 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Electrical Characteristics Parameter (Under Operating Conditions) Conditions Min TYP. Max Unit 1.225 1.250 1.275 V 1.764 1.800 1.836 V 2.450 2.500 2.550 V 3.235 3.300 3.365 V 0.2 % 1 % 15 18 mV 20 25 mV 26 33 mV 1.3 V o Reference Voltage APX1117-ADJ APX1117-1.8 APX1117-2.5 APX1117-3.3 Line Regulation APX1117-XXX APX1117-ADJ APX1117-1.8 Load Regulation APX1117-2.5 APX1117-3.3 Dropout Voltage (VIN-VOUT) Current Limit Minimum Load Current (Note 7) Thermal Regulation Ripple Rejection Temperature Stability θ JA Thermal Resistance Junction-to-Ambient θ JC Thermal Resistance Junction-to-Case Note: TA = 25 C, (VIN-VOUT) = 1.5V IO = 10mA o IOUT = 10mA, TA = 25 C, 3.3V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 4V≦VIN≦12V o IOUT = 10mA, TA = 25 C, 4.8V≦VIN≦12V IO = 10mA,VOUT+1.5V<VIN<12V, o TA = 25 C VIN=3.3V,Vadj=0,0mA<Io<1A, o TA = 25 C (Note 4, 5) VIN = 3.3V, 0mA<Io<1A, o TA = 25 C (Note 4, 5) VIN = 4V, 0mA<Io<1A, o TA = 25 C (Note 4, 5) VIN = 5V, 0≦IOUT≦1A, o TA = 25 C (Note 4, 5) APX1117-ADJ/1.8/2.5/3.3 IOUT = 1A (Note 6) APX1117-ADJ/1.8/2.5/3.3 (VIN-VOUT) = 5V APX1117-XXX o o 0 C≦TJ≦125 C o TA = 25 C, 30ms pulse F = 180Hz, COUT = 25uF Tantalum, IOUT = 1A APX1117-XXX VIN = VOUT+3V IO = 10mA 1. 1 A 5 10 mA 0.008 0.04 %/W 60 0.5 70 dB % SOT223-3L: Control Circuitry/Power Transistor (Note 8) TO252-3L: Control Circuitry/Power Transistor (Note 9) 107 73 SOT223-3L: Control Circuitry/Power Transistor (Note 8) TO252-3L: Control Circuitry/Power Transistor (Note 9) 12 16 O C/W O C/W 4. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package. 5. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. 6. ΔVOUT = 100mV 7. Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. 8. Test condition for SOT223-3L: TA=27 °C, no air flow, 2 oz copper, 5mmX5mm pad. 9. Test condition for TO252-3L: TA=27 °C, no air flow, 2 oz copper, 5mmX5mm pad. APX1117 Rev. 1 4 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Typical Performance Characteristics 0.20 2. 0 Output Voltage Deviation (%) 1. 8 1. 6 Dropout Voltage (V) 1. 4 1. 2 0 I load=800mA -0.20 Tj = 25 oC 1. 0 -0.40 0. 8 Tj = 125 oC 0. 6 -0.80 0. 4 0. 2 0 0 250 500 Output Current (mA) 750 -1 -25 1000 Dropout Voltage vs Output Current 0 25 50 Temperature (oC) 75 100 125 Load Regulation vs Temperature 2 1 0.8 1 0. 5 Output Voltage Deviation (%) Output Voltage Change (%) 1.5 0.6 0 0.4 -0.5 -1 0.2 -1.5 -2 -50 -25 0 25 50 Temperature (oC) 75 100 125 150 0 2 4 7.5 Cin=1uF Cout=10uF Tantalum 6.5 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) 30 10 12 C in = 1uF C out = 10 uF Tantalum Preload = 100mA 20 10 0 -10 -20 2 1 0 -1 0 Line Transient Response APX1117 Rev. 1 8 Line Regulation Load Current (A) Ou tput Voltage Deviation (mV) Output Voltage Deviation (mV) Input Voltage (V) Percent Change in Output Voltage vs Temperature 6 Input Voltage (V) 10 20 30 40 50 TIME (us) 60 70 80 90 100 Load Transient Response 5 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Typical Application Circuit 5V 5V C1 10uF C1 10uF Vin Vin Vout C2 22uF GND Vo Vout 3.3V/1A R1 121 Ω R2 121 Ω Adj Tab is Vout 2.5V/1A C2 22uF Tab is Vout ( 5V/3.3V fixed output ) ( 5V/2.5V ADJ output ) Note: Vo = VREF ∗ (1+ R2 ) R1 Marking Information (1) TO252-3L (Top view) Logo Part Number X1117 for ADJ X17-VV : 18 for 1.8V 25 for 2.5V 33 for 3.3V G : Green X17-VV YY WW X X Internal Code Xth Week:01~52 Year: "07" = 2007 "08" = 2008 ~ (2) SOT223-3L (Top view) Logo YMX APX1117 Rev. 1 6 of 8 www.diodes.com ~ Part Number X 1 7- VV X X1117 for ADJ X17-VV : 18 for 1.8V 25 for 2.5V 33 for 3.3V ID Code Month: A ~L = 01~12 Year: "7 " = 2007 "8" = 2008 G : Green JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR Package Information (All Dimensions in mm) 0.88/1.27 (1) TO252-3L 6.354/6.80 Typ 6.58 7.2 11.0 5.40/6.20 Typ 5.57 5.6 5.20/5.50 Typ 5.35 5.6 2.0 2.25 1.2 2.28 BSC. 4.57 BSC. Land Pattern Recommendation (Unit: mm) 0.64/1.02 Typ 0.83 0.89/ 1.14 0.45/0.58 Typ 0.52 9.00/10.40 Typ 9.70 SEE NOTE2 0.61 Typ 0.51 SEATING PLANE 2.18/2.40 Typ 2.29 0.45/0.58 Typ 0.52 (2) SOT223-3L 6.30/6.70 Nom 6.50 2.90 3.15 Ref. 1.6 3.30/3.70 Nom 3.50 1.50/2.00 Nom 2.00 2.3 1.2 Land Pattern Recommendation (Unit: mm) 0.60/0.70 Nom 0.80 0°/10° Nom 5° 13° 7 of 8 www.diodes.com 1.50/ 1.80 Nom 1.65 0.010/0.15 Nom 0.05 2.3 Basic 4.6 Basic 13° APX1117 Rev. 1 6.4 6.70/7.30 Nom 7.00 1.6 3.3 0.91/1.10 Nom 1.00 0.28/0.32 Seating Plane Nom 0.30 JUNE 2007 © Diodes Incorporated APX1117 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR IMPORTANT NOTICE Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages. LIFE SUPPORT Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the President of Diodes Incorporated. APX1117 Rev. 1 8 of 8 www.diodes.com JUNE 2007 © Diodes Incorporated