CURRENT 35.0 Amperes VOLTAGE 50 to 1000 Volts AR3505 THRU AR3510 Features · Plastic material used carries Underwriters Laboratory Classification 94V-0 · Low cost construction utilizing void-free molded plastic technique · Low cost · Diffused junctions · Low leakage · High surge capability · High temperature soldering guaranteed : 250℃ for 10 seconds AR 0.185(4.7) 0.165(4.2) 0.250(6.4) 0.235(6.0) Mechanical Data 0.410(10.4) 0.380(9.7) 0.225(5.7) 0.215(5.5) · Case : AR molded plastic · Terminals : Plated terminals, solderable per MIL-STD-750, method 208 · Polarity : Color ring denotes cathode end · Mounting Position : Any · Weight : 0.07 ounce, 1.8 gram Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols AR 3505 AR 351 AR 352 AR 354 AR 356 AR 358 AR 3510 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TC=150℃ I(AV) 35.0 Amps Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) TJ=150℃ IFSM 500 Amps Maximum instantaneous forward voltage at 35.0A VF 1.0 Volts Maximum DC reverse current at rated DC blocking voltage TC=25℃ TC=100℃ IR 5.0 250 μA Typical reverse recovery time (Note 2) trr 3.0 μS Typical junction capacitance (Note 1) TJ=25℃ CJ 300 pF RθJC TJ TSTG 1.0 ℃/W -50 to +175 ℃ Typical thermal resistance (Note 3) Operating and storage temperature range Notes: (1) Measured at 1MHz and applied reverse voltage of 4.0V dc. (2) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to case, single side cooled. 35 FIG.1 MAXIMUM FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) RATINGS AND CHARACTERISTIC CURVES AR3505 THRU AR3510 SINGLE PHASE HALF SINE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 30 25 20 15 10 5 0 125 135 145 155 165 O AMBIENT TEMPERATURE. ( C) 175 INSTANTANEOUS REVERSE CURRENT. (uA) 10 1.0 Tj=25 C PULSE WIDTH-300uS 2% DUTY CYCLE O 0.1 0.6 1.0 1.4 1.8 FORWARD VOLTAGE. (V) 2.2 8.3ms Single Half Wave JEDEC Method 500 100 50 1 100 100 2 60 40 Tj=100 C O 20 10 6 4 2 1 0.6 0.4 Tj=25 OC 0.2 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSEVOLTAGE. (%) 2.6 500 Tj=25 C O 100 50 1 f=1.0MHz Vsig=50mVp-p 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL REVERSE CHARACTERISTICS FIG.5- TYPICAL JUNCTION CAPACITANCE 1000 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) FIG.3- TYPICAL FORWARD CHARACTERISTICS 1000 1000 FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 5 10 20 50 REVERSE VOLTAGE. (V) 1 00 1 00