SIPEX AS2830

AS2830
3A Low Dropout Voltage Regulator
Adjustable & Fixed Output,
Fast Response
FEATURES
APPLICATIONS
• Adjustable Output Down To 1.2V
• Fixed Output Voltages 1.5, 2.5, 3.3, 5.0V
• Output Current Of 3A
• Low Dropout Voltage 1.1V Typ.
• Extremely Tight Load And Line Regulation
• Current & Thermal Limiting
• Standard 3-Terminal Low Cost TO-220, TO-263 & TO-252
• Similar To Industry Standard LT1085/LT1585
• Powering VGA & Sound Card
• Power PCSupplies
• SMPS Post-Regulator
• High Efficiency “Green” Computer Systems
• High Efficiency Linear Power Supplies
• Portable Instrumentation
• Constant Current Regulators
• Adjustable Power Supplies
• Battery charger
PRODUCT DESCRIPTION
The AS2830 is a low power 3A adjustable and fixed voltage regulator that is very easy to use. It requires only 2 external resistors to
set the output voltage for adjustable version. The AS2830 are designed for low voltage applications that offers lower dropout voltage
and faster transient response. This device is an excellent choice for use in powering low voltage microprocessor that require a lower
dropout, faster transient response to regulate from +2.5V to 3.8V supplies and as a post regulator for switching supplies applications.
The AS2830 features low dropout of a maximum 1.2 volts.
The AS2830 offers over current limit and full protection against reversed input polarity, reversed load insertion, and positive and
negative transient voltage. On-Chip trimming adjusts the reference voltage to 1%. The IQ of this device flows into the load, which
increases efficiency.
The AS2830 are offered in a 3-pin TO-220, TO-263 & TO-252 packages compatible with other 3 terminal regulators. For a 5A low
dropout regulator refer to the AS2850 data sheet.
ORDERING INFORMATION
TO-220
3-PIN
AS2830YU-X
DD PLASTIC
3-PIN
AS2830YT-X
TO-252
DPAK
PIN CONNECTIONS
AS2830YR-X
X = Output Voltage (1.5V, 2.5V, 3.3V, 5.0V and Blank for Adj.)
Y= Output Tolerance, (Y= A for 1%
Blank for 2%)
TO-263-3 (T)
TO-220-3 (U)
AS2830
1
2
3
AS2830
1
2
TO-252 (R)
AS2830
1
2
3
3
ADJ/GND VOUT VIN
Front View
ADJ/GND VOUT VIN
Top View
ADJ/GND VOUT VIN
Front View
Rev. 10/6/00
AS2830
ABSOLUTE MAXIMUM RATINGS
Lead Temp. (Soldering, 10 Seconds) .............................. 300°C
Storage Temperature Range ............................ -65° to +150°C
Operating Junction Temperature Range ......................
AS2830 Control Section ............................ -45°C +125°C
AS2830 Power Transistor...........................-45°C +150°C
Maximum Input Voltage ...................................... 10V
Input to Output Voltage Differential Max ........... 8.8V
ELECTRICAL CHARACTERISTICS (NOTE 1) at IOUT = 10mA, TA=25°C, unless otherwise specified.
AS2830A
AS2830
PARAMETER
CONDITIONS
Typ
Min
Max
Min
Units
Max
1.5V Version
Output Voltage (Note 2)
AS2830-1.5V, 0 ≤IOUT≤3A, 2.75V≤VIN ≤10V
1.5
1.5
1.485
1.470
1.515
1.530
1.470
1.455
1.530
1.545
V
2.5V Version
Output Voltage (Note 2)
AS2830-2.5V, 0 ≤IOUT≤3A, 4.0V≤VIN ≤10V
2.5
2.5
2.475
2.450
2.525
2.550
2.450
2.425
2.550
2.575
V
3.3V Version
Output Voltage (Note 2)
AS2830-3.3V, 0 ≤IOUT≤3A, 4.75V≤VIN ≤10V
3.3
3.3
3.270
3.240
3.330
3.360
3.230
3.201
3.370
3.399
V
5.0V Version
Output Voltage (Note 2)
AS2830-5.0V, 0 ≤IOUT≤3A, 6.5V≤VIN ≤10V
5.0
5.0
4.95
4.90
5.05
5.10
4.900
4.850
5.100
5.150
V
1.238
1.225
1.263
1.270
1.225
1.212
1.270
1.288
V
1.250
All Voltage Options
Reference Voltage (VREF)
Min. Load Current (Note 3)
Line Regulation (∆VREF (VIN))
Load Regulation (∆VREF (IOUT))
Dropout Voltage
Current Limit
IOUT (MAX)
Long Term Stability
Thermal Regulation
(∆VOUT (Pwr))
Temperature Stability
(∆VOUT (T))
Output Noise, RMS
Thermal Resistance
VIN≤ 7V, P≤ PMAX
1.5V≤ (VIN -VOUT)≤(VIN-VOUT) MAX,
10mA≤IOUT≤3A
1.5V≤ (VIN -VOUT)≤ (VIN-VOUT) MAX
2.75V≤VIN ≤7V, IOUT=10mA, TJ=25°C
(Note 3)
VIN ≤7V, IOUT=0mA, TJ=25°C
(Note 2)
10mA≤IOUT ≤3A, (VIN-VOUT)=3V, TJ=25°C
(Note 3)
0≤IOUT ≤3A, VIN=7V, TJ=25°C
(Note 2)
IOUT =3A
∆VREF=1%
IOUT≤ 3A
VIN=7V
1.4V≤ (VIN- VOUT) (Note3)
TA=125°C, 1000 Hrs.
TA=25°C, 20 ms pulse
5
0.005
10
0.2
10
0.2
mA
%
0.005
0.2
0.2
%
0.05
0.3
0.3
%
0.05
0.3
0.3
%
1.1
1.2
1.2
V
A
4.0
0.3
(Note
2)
0.01
3.2
3.2
1
1
%
0.020
0.020
%/W
0.25
10Hz to 10kHz TA = 25°c
Junction to Tab
TO-220
Junction to Ambient
Junction to Tab
DD Package
Junction to Ambient
%
0.003
3.0
60
3.0
60
3.0
60
3.0
60
%V
°C/W
The Bold specifications apply to the full operating temperature range.
Note 1: Changes in output voltage due to heating effects are covered under the specification for thermal regulation.
Note 2: Fixed Version Only
Note 3: Adjustable Version Only
Rev. 10/6/00
AS2830
APPLICATION HINTS
The AS2830 incorporates protection against over-current
faults, reversed load insertion, over temperature operation, and
positive and negative transient voltage. However, the use of
an output capacitor is required in order to improve the stability
and the performances.
Reducing parasitic resistance and inductance
One solution to minimize parasitic resistance and inductance is
to connect in parallel capacitors. This arrangement will
improve the transient response of the power supply if your
system requires rapidly changing current load condition.
Stability
The output capacitor is part of the regulator’s frequency
compensation system. Either a 22µF aluminum electrolytic
capacitor or a 10µF solid tantalum capacitor between the
output terminal and ground guarantees stable operation for all
operating conditions.
However, in order to minimize overshoot and undershoot, and
therefore optimize the design, please refer to the section
‘Ripple Rejection’.
Thermal Consideration
Although the AS2830 offers some limiting circuitry for
overload conditions, it is necessary not to exceed the
maximum junction temperature, and therefore to be careful
about thermal resistance. The heat flow will follow the lowest
resistance path, which is the Junction-to-case thermal
resistance. In order to insure the best thermal flow of the
component, a proper mounting is required. Note that the case
of the device is electrically connected to the output. In case
the case has to be electrically isolated, a thermally conductive
spacer can be used. However do not forget to consider its
contribution to thermal resistance.
Ripple Rejection
Ripple rejection can be improved by adding a capacitor
between the ADJ pin and ground as shown in figure 6. When
ADJ pin bypassing is used, the value of the output capacitor
required increases to its maximum (22µF for an aluminum
electrolytic capacitor, or 10µF for a solid tantalum capacitor).
If the ADJ pin is not bypass, the value of the output capacitor
can be lowered to 10µF for an electrolytic aluminum capacitor
or 4.7µF for a solid tantalum capacitor.
However the value of the ADJ-bypass capacitor should be
chosen with respect to the following equation:
C = 1 / (6.28 * FR * R1)
Where C
= value of the capacitor in Farads (select an
equal or larger standard value),
FR = ripple frequency in Hz,
R1 = value of resistor R1 in Ohms.
Assuming:
VIN = 10V, VOUT = 5V, IOUT = 1.5A, TA = 50°C/W,
θ Heatsink Case = 6°C/W, θ Heatsink Case = 0.5°C/W, θ JC = 3°C/W
Power dissipation under this condition
PD = (VIN – VOUT) * IOUT = 7.5W
Junction Temperature
TJ = TA + PD * (θ Case - HS+ θ HS + θ JC)
For the Control Sections
TJ = 50 + 7.5*(0.5 +6=3) = 121.25°C
121.25°C < TJ (max) for the Control & Power Sections.
In both case reliable operation is insured by adequate junction
temperature.
If an ADJ-bypass capacitor is use, the amplitude of the output
ripple will be independent of the output voltage. If an ADJbypass capacitor is not used, the output ripple will be
proportional to the ratio of the output voltage to the reference
voltage:
M = VOUT / VREF
Where M = multiplier for the ripple seen when the ADJ pin
is optimally bypassed.
VREF = Reference Voltage
Rev. 10/6/00
AS2830
Basic Adjustable Regulator
VIN
VOUT
AS2830
R1
VREF
VIN
5V
AS2830
VOUT
3.3V
C2
10uF
C1
10uF
IADJ
50µA
Basic Fixed Regulator
R2
VOUT = VREF * ( 1 + R2/R1) + IADJ * R2
Fig.2 Basic Adjustable Regulator
Output Voltage
Consider Figure 2. The resistance R1 generates a constant
current flow, normally the specified load current of 10mA.
This current will go through the resistance R2 to set the overall
output voltage. The current IADJ is very small and constant.
Therefore its contribution to the overall output voltage is very
small and can generally be ignored.
Output Voltage
The fixed voltage LDO voltage regulators are simple to use
regulators since the VOUT is preset to the specifications. It is
important however, to provide the proper output capacitance
for stability and improvement. For most operating conditions
a capacitance of 22uF tantalum or 100uF electrolytic will
ensure stability and prevent oscillation.
Load Regulation
Parasitic line resistance can degrade load regulation. In order
not to affect the behavior of the regulator, it is best to connect
directly the R1 resistance from the resistor divider to the case,
and not to the load. For the same reason, it is best to connect
the resistor R2 to the Negative side of the load.
VIN
RP Parasitic Line
Resistance
AS2830
Connect R1 to
Case of Regulator
R1
RL
R2
Connect R2 to Load
Fig.3 Basic Adjustable Regulator
Rev. 10/2/00
AS2830
TYPICAL APPLICATIONS
VIN
VIN
IN
AS2830
5V
+
10µF
AS2830
*C 1 improves ripple rejection. XC
should be ~ R 1 at ripple frequency.
VOUT
OUT
ADJ
R2
Fig. 5 Typical Adjustable Regulator
Fig. 4 3A Current output Regulator
(Note A)
C2
R1
VOUT = VREF (1 + R2 ) + IADJ R2
R1
LOAD
VOUT
OUT
ADJ
R1
ADJ
IN
AS2830
C1
C1
VIN
IN
OUT
VIN
+
150µF
+
C1
10µF*
AS2830
TTL
Input
5V
OUT
121Ω
1%
ADJ
R1
121Ω
1%
R2
365Ω
1%
IN
(Note A)
+
10µF
100µF
1k
2N3904
1k
365Ω
1%
Note A: VIN(MIN) = (Intended VOUT) + (VDROPOUT (MAX))
Note A: VIN(MIN)= (Intended VOUT) + (VDROPOUT (MAX))
Fig. 6
Improving Ripple Rejection
Fig.7 5V Regulator with Shutdown
Rev. 10/2/00
AS2830
TYPICAL CHARACTERISTICS
Rev. 10/2/00