September 2006 Advance Information AS7C1028 ® 5V 256K X 4 CMOS SRAM (Common I/O) Features • Industrial (-40o to 85oC) temperature • Organization: 262,144 words × 4 bits • High speed • 28-pin JEDEC standard packages - 400 mil SOJ • ESD protection ≥ 2000 volts - 12 ns address access time - 6 ns output enable access time • Low power consumption via chip deselect • One chip select plus one Output Enable pin • Bidirectional data inputs and outputs • TTL-compatible Logic block diagram Pin arrangement VCC GND I/O3 262,144 x 4 Array (262,144) Sense amp A0 A1 A2 A3 A4 A5 A6 A7 Address decoder Input buffer A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 CE OE GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AS7C1028 28 Pin SOJ (400 mil) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC A17 A16 A15 A14 A13 A12 A11 NC I/O3 I/O2 I/O1 I/O0 WE I/O0 A8 A9 Address decoder WE Control circuit OE CE A A A A A A A A 10 11 12 13 14 15 16 17 12/5/06; V.1.0 Alliance Memory P. 1 of 8 Copyright © Alliance Memory. All rights reserved. AS7C1028 ® Functional description The AS7C1028 is a 5V high-performance CMOS 1,048,576-bit Static Random-Access Memory (SRAM) device organized as 262,144 words × 4 bits. It is designed for memory applications requiring fast data access at low voltage, including PentiumTM, PowerPCTM, and portable computing. Alliance’s advanced circuit design and process techniques permit 5.0V operation without sacrificing performance or operating margins. The device enters standby mode when CE is high. Equal address access and cycle times (tAA, tRC, tWC) of 12 ns with output enable access times (tOE) of 6 ns are ideal for high-performance applications. The chip enable (CE) input permits easy memory expansion with multiple-bank memory organizations. A write cycle is accomplished by asserting chip enable (CE) and write enable (WE) LOW. Data on the input pins I/O0-I/O7 is written on the rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should drive I/O pins only after outputs have been disabled with output enable (OE) or write enable (WE). A read cycle is accomplished by asserting chip enable (CE) and output enable (OE) LOW, with write enable (WE) high. The chip drives I/O pins with the data word referenced by the input address. When chip enable or output enable is high, or write enable is low, output drivers stay in high-impedance mode. All chip inputs and outputs are TTL-compatible. Operation is from a single 5.0±0.5V supply. The AS7C1028 is packaged in high volume industry standard packages. Absolute maximum ratings Parameter Symbol Min Max Unit Voltage on VCC relative to GND Vt1 –0.5 +7.0 V Voltage on any pin relative to GND Vt2 –0.5 VCC + 0.5 V Power dissipation PD – 1.25 W Storage temperature (plastic) Tstg –55 +125 oC Ambient temperature with VCC applied Tbias –55 +125 o DC current into outputs (low) IOUT – 50 C mA Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Truth table CE WE OE Data Mode H X X High Z Standby (ISB, ISB1) L H H High Z Output disable (ICC) L H L DOUT Read (ICC) L L X DIN Write (ICC) Notes: H = VIH, L = VIL, x = Don’t care. VLC = 0.2V, VHC = VCC - 0.2V. Other inputs ≥ VHC or VLC. 12/5/06; V.1.0 Alliance Memory P. 2 of 8 AS7C1028 ® Recommended operating conditions Parameter Symbol Min Typical Max Unit VCC 4.5 5.0 5.5 V Supply voltage Input voltage VIH 2.2 – VCC+0.5 V VIL(1) -0.5(1) – 0.8 V TA –40 – 85 o Ambient operating temperature (Industrial) C Note: 1 VIL min = –1.5V for pulse width less than 10ns, once per cycle. DC operating characteristics (over the operating range)1 AS7C1028-12 Parameter Symbol Test conditions Min Max Unit Input leakage current |ILI| VCC = Max, Vin = GND to VCC – 5 µA Output leakage current |ILO| VCC = Max, CS = VIH, VOUT = GND to VCC – 5 µA Operating power supply current ICC VCC = Max, CE ≤ VIL f = fMax, IOUT = 0mA – 170 mA ISB VCC = Max, CE > VIH f = fMax, IOUT = 0mA – 40 mA ISB1 VCC = Max, CE > VCC–0.2V VIN < GND + 0.2V or VIN > VCC–0.2V, f = 0 – 10 mA VOL IOL = 8 mA, VCC = Min – 0.4 V VOH IOH = –4 mA, VCC = Min 2.4 – V Standby power supply current Output voltage Capacitance (f = 1MHz, Ta = room temperature, VCC = NOMINAL)2 Parameter Symbol Signals Test conditions Max Unit Input capacitance CIN A, CE, WE, OE Vin = 3dV 8 pF I/O capacitance CI/O I/O Vout = 3dV 8 pF Note: This parameter is guaranteed by device characterization, but is not production tested. 12/5/06; V.1.0 Alliance Memory P. 3 of 8 AS7C1028 ® Read cycle (over the operating range)3,9 AS7C1028-12 Parameter Symbol Min Max Unit Notes Read cycle time tRC 12 – ns Address access time tAA – 12 ns 3 Chip enable (CE) access time tACE – 12 ns 3 Output enable (OE) access time tOE – 6 ns Output hold from address change tOH 4 – ns 5 CE LOW to output in low Z tCLZ 3 – ns 4, 5 CE HIGH to output in high Z tCHZ 0 6 ns 4, 5 OE LOW to output in low Z tOLZ 0 – ns 4, 5 OE HIGH to output in high Z tOHZ 0 5 ns 4, 5 Power up time tPU 0 – ns 4, 5 Power down time tPD – 12 ns 4, 5 Key to switching waveforms Rising input Falling input Undefined output/don’t care Read waveform 1 (address controlled)3,6,7,9 tRC Address tOH tAA Dout Data valid Read waveform 2 (CE controlled)3,6,8,9 tRC1 CE tOE OE tOLZ tOHZ tCHZ tACE Dout Data valid tCLZ Supply current 12/5/06; V.1.0 tPU tPD 50% ICC ISB 50% Alliance Memory P. 4 of 8 AS7C1028 ® Write cycle (over the operating range)11 AS7C1028-12 Parameter Symbol Min Max Unit Write cycle time tWC 12 – ns Chip enable to write end tCW 10 – ns Address setup to write end tAW 10 – ns Notes Address setup time tAS 0 – ns Write pulse width tWP 10 – ns Write recovery time tWR 0 – ns Address hold from end of write tAH 0 – ns Data valid to write end tDW 7 – ns Data hold time tDH 0 – ns 4, 5 Write enable to output in high Z tWZ 0 5 ns 4, 5 Output active from write end tOW 3 – ns 4, 5 Shaded areas contain advance information. Write waveform 1 (WE controlled)10,11 tWC tAW tAH tWR Address tWP WE tAS tDW tDH Data valid Din tWZ tOW Dout Write waveform 2 (CE controlled)10,11 tWC tAW tAH tWR Address tAS tCW CE tWP WE tWZ Din tDW tDH Data valid Dout 12/5/06; V.1.0 Alliance Memory P. 5 of 8 AS7C1028 ® AC test conditions - Output load: see Figure B or Figure C. Input pulse level: GND to VCC. See Figure A. Input rise and fall times: 3 ns. See Figure A. Input and output timing reference levels: 1.5V. Thevenin equivalent 168Ω Dout +1.72V (5V) VCC +5V 320Ω 480Ω VCC GND 90% 10% 90% 3 ns 10% Figure A: Input pulse Dout 255Ω C(13) GND Figure B: Output load Dout 350Ω C(13) GND Figure C: Output load Notes: 1 2 3 4 5 6 7 8 9 10 11 12 13 During VCC power-up, a pull-up resistor to VCC on CE is required to meet ISB specification. This parameter is sampled, but not 100% tested. For test conditions, see AC Test Conditions, Figures A, B, C. These parameters are specified with CL = 5pF, as in Figures B or C. Transition is measured ±200mV from steady-state voltage. This parameter is guaranteed, but not tested. WE is High for read cycle. CE and OE are Low for read cycle. Address valid prior to or coincident with CE transition Low. All read cycle timings are referenced from the last valid address to the first transitioning address. CE or WE must be High during address transitions. Either CE or WE asserting high terminates a write cycle. All write cycle timings are referenced from the last valid address to the first transitioning address. CE1 and CE2 have identical timing. C=30pF, except on High Z and Low Z parameters, where C=5pF. 12/5/06; V.1.0 Alliance Memory P. 6 of 8 AS7C1028 ® Package diagrams 28-pin SOJ 28-pin SOJ 400 mil e 400 mil Min Max in mils D E1 E2 B A A1 Pin 1 b c Seating Plane A2 A A1 A2 B b c D E E1 E2 e 0.132 - 0.105 0.115 0.024 0.032 0.013 0.021 0.720 0.012 0.354 0.378 0.395 0.405 0.430 0.405 0.430 0.440 0.050 BSC E2 Note: This part is compatible with both pin numbering conventions used by various manufacturers. 12/5/06; V.1.0 Alliance Memory .0146 0.062 P. 7 of 8 AS7C1028 ® Ordering information Package Plastic SOJ, 400 mil Volt/Temp 12 ns 5V industrial AS7C1028-12JIN Part numbering system AS7C SRAM prefix 1028 –XX Device number Access time X Package: J=SOJ 400 mil I X Temperature range: I = -40C to 85C N=Lead Free Part ® Alliance Memory, Inc. 1116 South Amphlett San Mateo, CA 94402 Tel: 650-525-3737 Fax: 650-525-0449 Copyright © Alliance Memory All Rights Reserved Part Number: AS7C1028 Document Version: v.1.0 www.alliancememory.com © Copyright 2003 Alliance Memory, Inc. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.