ASL563 High Gain, Low Noise Amplifier Description Features · · · · 33 dB Gain at 900 MHz 1.0 dB NF at 900 MHz Two-stage LNA Two power supplies in Type 2 ASL563 is a two-stage LNA for GPS, DMB, and satellite receiver low noise blocks. It has a low noise, high gain, and high linearity over a wide range of frequency up to 6 GHz. It is also suitable for use in the low noise amplifier block of the mobile wireless systems of T-DMB, CDMA, GSM, PCS, WCDMA, WiBro, WiMAX, and WLAN so on. The amplifier is available in an SOT-363 package and passes the stringent DC, RF, and reliability tests. Package Style: SOT-363 Typical Performance Parameters Units Frequency Application Circuit Typical MHz 900 1950 2450 Gain dB 33 26 22 S11 dB -15 -15 -15 S22 dB -20 -20 -14 dBm 23 Noise Figure dB 0.9 0.9 1.0 Output P1dB dBm 11 14 14 Current mA 50 50 50 V 5 5 5 Output IP3 Device Voltage 1) 29 2) 31 2) 1) OIP3 is measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 2) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. · 900 MHz · 1800 MHz · 1950 MHz · 2400 ~ 2500 MHz · GPS (TYPE 1) · GPS (TYPE 2 / Strip lines) · 1163~1210 / 1204~1240 MHz · 1558~1577 MHz · GPS (TYPE 2 / Without strip lines) · 2400 ~ 2500 MHz (3V) Product Specifications* Parameters Units Frequency Min MHz Typ 900 Gain dB S11 dB -15 S22 dB -20 Output IP3 dBm 31 21 33 23 Noise Figure dB Output P1dB dBm Current mA 50 V 5 Device Voltage Max 1.0 9 1.3 11 * 100% in-house DC & RF testing is done on packaged products before taping. Pin Configuration Absolute Maximum Ratings Pin No. Function Rating 1 GND1 Operating Case Temperature -40 to +85°C 2 GND2 Storage Temperature -40 to +150°C 3 OUT2 / VDD2 +5.5 V 4 IN2 Operating Junction Temperature +150°C 5 OUT1 / VDD1 Input RF Power (CW, 50ohm matched)* 22 dBm 6 IN1 Parameters Device Voltage * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Outline Drawing Symbols A A1 A2 b C D F E1 e e1 L Pin NO. Function Pin NO. Function. 1 GND1 4 IN2 2 GND2 5 OUT1 / VDD1 3 OUT2 / VDD2 6 IN1 MIN 0.90 0.025 0.875 0.20 0.10 1.90 1.15 2.00 ---- Dimensions (In mm) NOM 1.00 0.062 0.937 0.30 0.125 2.00 1.25 2.10 0.65BSC 1.30BSC 0.425REF MAX 1.10 0.10 1.00 0.40 0.15 2.10 1.35 2.20 ---- Ordering Information Part Number 2/22 Description ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions Gp F = 900 MHz Power Gain APPLICATION CIRCUIT 900 MHz TYP. MAX. Unit 33 dB Noise Figure NF F = 900 MHz 0.9 dB Input Return Loss RLin F = 900 MHz -15 dB Output Return Loss RLout F = 900 MHz -20 dB Po(1dB) F = 900 MHz 11 dBm OIP3 F = 900 MHz 23 dBm Icc F = 900 MHz, Non-RF 50 mA 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +5 V / 50mA MIN. Circuit Current 1) OIP3 is measured with two tones at an output power of +0 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1.1 kW C7=1 mF VDD R5=10 kW C1=100 pF R4=91 W R3=82 W ASL563 L1=15 nH R1=12 kW L2=33 nH L4=12 nH C5=3 pF m m 7 L3=33 nH RF OUT *P2 *P1 VDD C2=1 mF 7mm C4=100 pF R2=1.2kW Bottom C3=10 nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 5.3 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 50 40 S21 30 10 S22 S(2,2) S(1,1) S - parameter [dB] 20 0 -10 S11 S22 S11 -20 -30 S12 -40 -50 600 700 800 900 1000 1100 1200 freq (600.0MHz to 1.200GHz) Frequency [MHz] 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0 0.5 600 0.6 0 500 1000 1500 2000 2500 3000 3500 700 Frequency (MHz) 3/22 800 900 1000 1100 1200 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions Gp F = 1.8 GHz Power Gain APPLICATION CIRCUIT 1800 MHz TYP. MAX. Unit 27 dB Noise Figure NF F = 1.8 GHz 0.9 dB Input Return Loss RLin F = 1.8 GHz -15 dB Output Return Loss RLout F = 1.8 GHz -20 dB Po(1dB) F = 1.8 GHz 14 dBm OIP3 F = 1.8 GHz 30 dBm Icc F = 1.8 GHz, Non-RF 50 mA 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +5 V / 50mA MIN. Circuit Current 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1.1 kW C7=1 mF VDD R5=10 kW C1=1.5 pF R4=33 W R3=27 W ASL563 L1=5.6 nH L2=15 nH R1=12 kW L4=5.6 nH C5=1.2 pF m m 7 L3=8.2 nH RF OUT *P2 *P1 VDD C2=1 mF 7mm C4=68 pF R2=1.2kW Bottom C3=10 nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 4.3 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 40 30 S21 10 S(2,2) S(1,1) S - parameter [dB] 20 0 -10 S22 S11 S22 S11 -20 -30 S12 -40 1200 1400 1600 1800 2000 2200 2400 freq (1.200GHz to 2.400GHz) Frequency [MHz] 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0 0.5 1200 0.6 0 500 1000 1500 2000 2500 3000 3500 1400 Frequency (MHz) 4/22 1600 1800 2000 2200 2400 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions Gp F = 1.95 GHz Noise Figure NF Input Return Loss RLin Output Return Loss 1950 MHz 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +5 V / 50mA TYP. MAX. Unit 26 dB F = 1.95 GHz 0.9 dB F = 1.95 GHz -15 dB RLout F = 1.95 GHz -20 dB Po(1dB) F = 1.95 GHz 14 dBm OIP3 F = 1.95 GHz 29 dBm Icc F = 1.95 GHz, Non-RF 50 mA Power Gain APPLICATION CIRCUIT MIN. Circuit Current 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1.1 kW C7=1 mF VDD R5=10 kW C1=1 pF R4=33 W R3=27 W ASL563 L1=4.7 nH L2=22 nH R1=12 kW L4=5.6 nH C5=1 pF m m 7 L3=8.2 nH RF OUT *P2 *P1 VDD C2=1 mF 7mm C4=68 pF R2=1.2kW Bottom C3=10 nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 3.7 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 40 30 S21 10 S(2,2) S(1,1) S - parameter [dB] 20 0 S11 S22 S22 -10 -20 S11 -30 S12 -40 1600 1700 1800 1900 2000 2100 2200 freq (1.600GHz to 2.200GHz) Frequency [MHz] 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0 0.5 1600 0.6 0 500 1000 1500 2000 2500 3000 3500 1700 Frequency (MHz) 5/22 1800 1900 2000 2100 2200 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions Gp F = 2.45 GHz Noise Figure NF Input Return Loss RLin Output Return Loss Power Gain APPLICATION CIRCUIT 2400 ~ 2500 MHz 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +5 V / 50mA Circuit Current MIN. TYP. MAX. Unit 22 dB F = 2.45 GHz 1.0 dB F = 2.45 GHz -15 dB RLout F = 2.45 GHz -14 dB Po(1dB) F = 2.45 GHz 14 dBm OIP3 F = 2.45 GHz 31 dBm Icc F = 2.45 GHz, Non-RF 50 mA 1) OIP3 is measured with two tones at an output power of +5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1.1 kW C7=1 mF VDD R5=10 kW C1=1.5 pF R4=33 W R3=27 W ASL563 L1=3.3 nH R1=12 kW L2=15 nH C5=1 pF RF OUT *P2 *P1 VDD C2=1 mF L4=3.3 nH m m 7 L3=15 nH 7mm C4=3 pF R2=1.2kW Bottom C3=10 nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 2.0 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 30 S21 20 S(2,2) S(1,1) S - parameter [dB] 10 0 -10 S11 S22 S11 -20 S22 S12 -30 -40 2100 2200 2300 2400 2500 2600 2700 2800 freq (2.100GHz to 2.800GHz) Frequency [MHz] 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0 0.5 2100 0.6 0 500 1000 1500 2000 2500 3000 3500 2200 Frequency (MHz) 6/22 2300 2400 2500 2600 2700 2800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 1) Symbol Test Conditions MIN. TYP. Gp F = 1.575 GHz 24 25 Power Gain GPS +3 V Unit dB Noise Figure NF F = 1.575 GHz 1.1 Input Return Loss RLin F = 1.575 GHz -14 dB Output Return Loss RLout F = 1.575 GHz -12 dB Po(1dB) F = 1.575 GHz 8 10 dBm OIP3 F = 1.575 GHz 14 16 dBm Icc F = 1.575 GHz, Non-RF 7.7 mA 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power 1575 MHz MAX. Circuit Current 1.3 dB 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R4=1.1 kW C7=1 mF VDD R5=8.2 kW C1=1.8 pF R6=33 W L4=6.2 nH C5=1.5 pF R3=33W ASL563 L1=6.8 nH R1=9.1kW L2=6.2 nH R2=1.2 kW RF OUT *P2 *P1 VDD C2=1 mF m m 7 L3=7.5 nH 7mm Bottom C4=68 pF C3=10 nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 2.8 mm, Width: 0.3 mm *P2 Length: 1.0 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 35 0 30 -5 25 S11 (dB) Gain (dB) -10 20 15 o -40 c o 25 c o 85 c 10 5 0 1400 1450 1500 1550 1600 1650 1700 1750 -15 -20 o 1800 Frequency (MHz) -30 1400 1550 1600 1650 1700 1750 1800 4 -15 Stability Factor -10 S22 (dB) 1500 5 -5 o -40 c o 25 c o 85 c -20 3 2 1 1450 1500 1550 1600 1650 Frequency (MHz) 7/22 1450 Frequency (MHz) 0 -25 1400 -40 c o 25 c o 85 c -25 1700 1750 1800 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 1.5 1.4 1.3 Noise Figure S(2,2) S(1,1) 1.2 S22 S11 1.1 1.0 0.9 0.8 0.7 0.6 0.5 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency (MHz) freq (1.400GHz to 1.800GHz) Gain vs. Temperature Current vs. Temperature 30 16 14 28 10 26 Gain (dB) Current (mA) 12 8 6 4 24 Frequency = 1575 MHz 22 2 0 -60 -40 -20 0 20 40 60 80 20 -60 100 -40 -20 0 80 100 35 30 14 25 Output IP3 (dBm) 12 P1dB (dBm) 60 Output IP3 vs. Tone Power (Frequency = 1575 MHz) 16 10 8 Frequency = 1575 MHz 6 20 15 o -40 c o 25 c o 85 c 10 5 -40 -20 0 20 40 60 80 100 0 -11 -10 -9 -8 o -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 Pout per Tone (dBm) Temperature ( C) 8/22 40 Temperature ( C) P1dB vs. Temperature 4 -60 20 o o Temperature ( C) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Strip lines (P1 & P2) Power Gain 1) Noise Figure 2) Input Return Loss 3) Output Return Loss GPS 3) 1 dB Gain Compression Output Power rd 3 Intercept Point 4) Output Power 1575 MHz +3 V Circuit Current Symbol Test Conditions MIN. TYP. Gp F = 1.575 GHz 24 25 MAX. Unit dB NF F = 1.575 GHz 1.1 RLin F = 1.575 GHz -15 dB RLout F = 1.575 GHz -15 dB Po(1dB) F = 1.575 GHz 8 10 dBm OIP3 F = 1.575 GHz 17 19 dBm Icc F = 1.575 GHz, Non-RF 7.7 mA 5) 1.3 dB 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (with the striplines at the Pin 1 and 2) RF IN2 BPF C7=10 nF C6=20 pF R4=1.1 kW C8=1 mF VDD2 L3=6.2 nH C1=1.2 pF RF OUT1 R6=27 W R3=24 W ASL563 L1=5.6 nH R1=9.1 kW L2=6.8 nH R2=1.2 kW L4=6.2 nH C5=1 pF RF OUT2 *P2 *P1 VDD1 C2=1 mF R5=8.2 kW Bottom C4=20 pF C3=10 nF RF IN1 Note: the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 1.0 mm, Width: 0.3 mm *P2 Length: 0.65 mm, Width: 0.3 mm 1st stage S-parameters & Noise Figure 30 S21 10 S(2,2) S(1,1) S - parameter [dB] 20 0 S11 S22 -10 S22 S12 -20 S11 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] freq (1.400GHz to 1.800GHz) 5 1.5 1.4 4 1.3 Noise Figure Stability Factor 1.2 3 2 1.1 1.0 0.9 0.8 1 0.7 0.6 0 0 500 1000 1500 2000 2500 3000 3500 0.5 1400 1450 1500 Frequency (MHz) 9/22 1550 1600 1650 1700 1750 1800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & Noise Figure 30 20 S21 0 S11 S22 S(2,2) S(1,1) S - parameter [dB] 10 S22 -10 -20 S11 S12 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 freq (1.400GHz to 1.800GHz) Frequency [MHz] 2.0 5 1.9 1.8 4 3 Noise Figure Stability Factor 1.7 2 1.6 1.5 1.4 1.3 1 1.2 1.1 0 0 500 1000 1500 2000 2500 3000 3500 1.0 1400 1450 Frequency (MHz) 10/22 1500 1550 1600 1650 1700 1750 1800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Strip lines (P1 & P2) Power Gain Noise Figure TYP. Gp F = 1.575 GHz 24 27 Circuit Current MAX. Unit dB NF F = 1.575 GHz 0.8 RLin F = 1.575 GHz -18 dB RLout F = 1.575 GHz -18 dB Po(1dB) F = 1.575 GHz 9 11 dBm OIP3 F = 1.575 GHz 20 22 dBm Icc F = 1.575 GHz, Non-RF 14 mA 3) 1 dB Gain Compression Output Power rd 3 Intercept Point 4) Output Power +3 V MIN. 3) Output Return Loss 1575 MHz Test Conditions 2) Input Return Loss GPS Symbol 1) 5) 0.9 dB 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (with the striplines at the Pin 1 and 2) RF IN2 BPF C7=10 nF C6=20 pF R4=1.2 kW C8=1 mF VDD2 L3=6.2 nH R5=9.1 kW R6=27 W C1=1.2 pF RF OUT1 C5=1 pF R3=24 W ASL563 L1=5.6 nH L2=6.8 nH R1=8.2 kW R2=1.2 kW RF OUT2 *P2 Bottom *P1 VDD1 C2=1 mF L4=6.2 nH C4=20 pF C3=10 nF RF IN1 Note: the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 1.5 mm, Width: 0.3 mm *P2 Length: 1.5 mm, Width: 0.3 mm 1st stage S-parameters & K-factor 30 20 S22 0 S(2,2) S(1,1) S - parameter [dB] S21 10 S11 S22 -10 S12 -20 -30 1400 S11 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] 5 freq (1.400GHz to 1.800GHz) Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 11/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & K-factor 30 20 S(2,2) S(1,1) S - parameter [dB] S21 10 0 S22 S11 S22 -10 -20 S11 S12 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] freq (1.400GHz to 1.800GHz) 5 Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 12/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Strip lines (P1 & P2) Power Gain Noise Figure Test Conditions Gp F = 1.575 GHz 2) Input Return Loss 1575 MHz +3 V Circuit Current TYP. MAX. Unit 30 dB NF F = 1.575 GHz 0.7 dB F = 1.575 GHz -18 dB RLout F = 1.575 GHz -18 dB Po(1dB) F = 1.575 GHz 10.5 dBm OIP3 F = 1.575 GHz 25.5 dBm Icc F = 1.575 GHz, Non-RF 28 mA 3) 1 dB Gain Compression Output Power rd 3 Intercept Point 4) Output Power MIN. RLin 3) Output Return Loss GPS Symbol 1) 5) 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (with the striplines at the Pin 1 and 2) RF IN2 BPF C7=10 nF C6=20 pF C8=1 mF R4=1.2 kW VDD2 L3=6.2 nH R5=6.8 kW R6=27 W C1=1.2 pF RF OUT1 C5=1 pF R3=5.6 W ASL563 L1=5.6 nH R1=6.8 kW L2=6.8 nH R2=1.2 kW RF OUT2 *P2 Bottom *P1 VDD1 C2=1 mF L4=6.2 nH C4=20 pF C3=10 nF Note: the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 1.0 mm, Width: 0.3 mm *P2 Length: 1.5 mm, Width: 0.3 mm 1st stage S-parameters & K-factor 30 20 0 S(2,2) S(1,1) S - parameter [dB] S21 10 S22 -10 S11 S12 -20 S22 S11 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] 5 freq (1.400GHz to 1.800GHz) Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 13/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & K-factor 30 20 S(2,2) S(1,1) S - parameter [dB] S21 10 0 S22 S22 -10 S11 S11 -20 S12 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] freq (1.400GHz to 1.800GHz) 5 Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 14/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Strip lines (P1 & P2) Unit Gp dB Noise Figure NF dB 1.1 1.0 Input Return Loss RLin dB -15 -15 Output Return Loss 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power Current RLout dB -15 -16 Po(1dB) dBm 10 10.5 OIP3 dBm 21 21 Icc mA 7.7 7.7 Vdd V 3 3 Power Gain GPS 1163 ~ 1210 MHz / 1204 ~ 1240 MHz Device Voltage +3 V Frequency [MHz] Symbol 1163-1210 1204-1240 24.5 26 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (with the striplines at the Pin 1 and 2) RF IN2 BPF R4=1.1 kW C7=10 nF C6=2 pF C8=1 mF VDD2 L3=5.6 nH R5=8.2 kW R6=27 W C1=1.2 pF RF OUT1 R3=24 W ASL563 L1=9.1 nH R1=9.1 kW L2=6.2 nH R2=1.2 kW RF OUT2 *P2 *P1 VDD1 C2=1 mF L4=9.1 nH C5=1.5 pF Bottom C4=2.4 pF C3=10 nF RF IN1 Note: the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 5.0 mm, Width: 0.3 mm *P2 Length: 2.5 mm, Width: 0.3 mm 1st stage S-parameters & K-factor 30 20 S21 S22 0 S(2,2) S(1,1) S - parameter [dB] 10 S22 -10 S11 -20 S12 S11 -30 -40 900 1000 1100 1200 1300 1400 Frequency [MHz] 5 freq (900.0MHz to 1.400GHz) Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 15/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & K-factor 30 20 S21 S22 S(2,2) S(1,1) S - parameter [dB] 10 0 S22 -10 S11 S11 -20 S12 -30 -40 900 1000 1100 1200 1300 1400 freq (900.0MHz to 1.400GHz) Frequency [MHz] 5 Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 16/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Strip lines (P1 & P2) Unit Gp dB Noise Figure NF dB 1.2 Input Return Loss RLin dB -14 Output Return Loss 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power Current RLout dB -16 Po(1dB) dBm 11 OIP3 dBm 18.5 Icc mA 7.7 Vdd V 3 Power Gain GPS 1558 ~ 1577 MHz +3 V Frequency [MHz] Symbol Device Voltage 1558-1577 25 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (with the striplines at the Pin 1 and 2) RF IN2 BPF R4=1.1 kW C7=10 nF C6=2.2 pF C8=1 mF VDD2 L3=3.3 nH R5=8.2 kW R6=27 W C1=1 pF RF OUT1 C5=1 pF R3=24 W ASL563 L1=5.6 nH R1=9.1 kW L2=5.6 nH R2=1.2 kW RF OUT2 *P2 Bottom *P1 VDD1 C2=1 mF L4=5.6 nH C4=100 pF C3=10 nF RF IN1 Note: the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 0.5 mm, Width: 0.3 mm *P2 Length: 2 mm, Width: 0.3 mm 1st stage S-parameters & K-factor 30 20 S21 S22 0 -10 S11 S(2,2) S(1,1) S - parameter [dB] 10 S11 S12 -20 S22 -30 -40 1300 1400 1500 1600 1700 1800 Frequency [MHz] freq (1.300GHz to 1.800GHz) 5 Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 17/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & K-factor 30 20 S21 S22 S11 S(2,2) S(1,1) S - parameter [dB] 10 0 S22 -10 S11 -20 S12 -30 -40 1300 1400 1500 1600 1700 1800 freq (1.300GHz to 1.800GHz) Frequency [MHz] 5 Stability Factor 4 3 2 1 0 0 500 1000 1500 2000 2500 3000 3500 Frequency (MHz) 18/22 ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter APPLICATION CIRCUIT (TYPE 2) Without strip lines Power Gain Noise Figure TYP. Gp F = 1.575 GHz 24 25 Circuit Current MAX. Unit dB NF F = 1.575 GHz 1.1 RLin F = 1.575 GHz -15 dB RLout F = 1.575 GHz -15 dB Po(1dB) F = 1.575 GHz 8 10 dBm OIP3 F = 1.575 GHz 17 19 dBm Icc F = 1.575 GHz, Non-RF 7.7 mA 3) 1 dB Gain Compression Output Power rd 3 Intercept Point 4) Output Power +3 V MIN. 3) Output Return Loss 1575 MHz Test Conditions 2) Input Return Loss GPS Symbol 1) 5) 1.3 dB 1) Total gain is sum of the 1st stage and 2nd stage amplifiers (not include filter loss). 2) NF is that of the 1st stage amplifier. 3) S11 is that of the 1st stage amplifier and S22 is that of the 2nd stage amplifier. 4) OIP3 is that of the 2nd stage amplifier measured with two tones at an output power of +0 dBm/tone separated by 1MHz. 5) Total current is the sum of the 1st stage and the 2nd stage amplifiers. Board Layout (FR4, 19.4x17.4 mm2, 0.8T) Top Schematic (without the stripline at the Pin 1 and 2) RF IN2 BPF R4=1.1 kW C7=10 nF C6=68 pF C8=1 mF VDD2 L3=4.7 nH R5=8.2 kW R6=27 W C1=1.2 pF RF OUT1 R3=51 W L4=5.6 nH C5=1.2 pF RF OUT2 Bottom ASL563 L1=5.1 nH R1=9.1 kW L2=5.6 nH VDD1 C2=1 mF R2=1.2 kW C4=68 pF C3=10 nF RF IN1 1st stage S-parameters & Noise Figure 30 S21 10 S(2,2) S(1,1) S - parameter [dB] 20 0 S22 S11 -10 S11 S22 S12 -20 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] freq (1.400GHz to 1.800GHz) 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0.6 0 0 500 1000 1500 2000 2500 3000 3500 0.5 1400 1450 1500 Frequency (MHz) 19/22 1550 1600 1650 1700 1750 1800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier 2nd stage S-parameters & Noise Figure 30 20 S22 S(2,2) S(1,1) S - parameter [dB] S21 10 0 S11 S22 -10 S11 -20 S12 -30 1400 1450 1500 1550 1600 1650 1700 1750 1800 Frequency [MHz] freq (1.400GHz to 1.800GHz) 5 2.0 1.9 4 1.8 3 Noise Figure Stability Factor 1.7 2 1.6 1.5 1.4 1.3 1 1.2 1.1 0 0 500 1000 1500 2000 2500 3000 3500 1.0 1400 1450 Frequency (MHz) 20/22 1500 1550 1600 1650 1700 1750 1800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions MIN. TYP. Gp F = 2.45 GHz 16 17 dB Noise Figure NF F = 2.45 GHz 1.2 dB Input Return Loss RLin F = 2.45 GHz -15 dB Output Return Loss RLout F = 2.45 GHz -14 dB Po(1dB) F = 2.45 GHz 9 11 dBm OIP3 F = 2.45 GHz 13 17 dBm Icc F = 2.45 GHz, Non-RF 10 mA Power Gain APPLICATION CIRCUIT 2400 ~ 2500 MHz 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +3 V / 10mA Circuit Current MAX. Unit 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1 kW C7=1 mF VDD R5=6.8 kW C1=1.8 pF R4=33 W R3=33 W ASL563 L1=3.3 nH R1=6.8 kW L2=15 nH C5=1 pF RF OUT *P2 *P1 VDD C2=1 mF L4=3.3 nH m m 7 L3=15 nH 7mm C4=10 pF R2=1.1 kW Bottom C3=10nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 2.5 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 30 20 S21 S22 0 -10 S(2,2) S(1,1) S - parameter [dB] 10 S22 S11 -20 S11 -30 S12 -40 2100 2200 2300 2400 2500 2600 2700 2800 Frequency [MHz] freq (2.100GHz to 2.800GHz) 5 1.5 4 1.3 3 1.1 1.4 Noise Figure Stability Factor 1.2 2 1.0 0.9 0.8 1 0.7 0 0.5 2100 0.6 0 500 1000 1500 2000 2500 3000 3500 2200 2300 Frequency (MHz) 21/22 2400 2500 2600 2700 2800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011 ASL563 High Gain, Low Noise Amplifier Parameter Symbol Test Conditions MIN. TYP. Gp F = 2.45 GHz 18 19 Noise Figure NF F = 2.45 GHz 1 Input Return Loss RLin F = 2.45 GHz -15 dB Output Return Loss RLout F = 2.45 GHz -15 dB Po(1dB) F = 2.45 GHz 9 11 dBm OIP3 F = 2.45 GHz 13 18 dBm Icc F = 2.45 GHz, Non-RF 15 mA Power Gain APPLICATION CIRCUIT 2400 ~ 2500 MHz 1 dB Gain Compression Output Power rd 3 Intercept Point 1) Output Power +3 V / 15mA Circuit Current MAX. Unit dB 1.1 dB 1) OIP3 is measured with two tones at an output power of -5 dBm/tone separated by 1MHz. Board Layout (FR4, 16x12 mm2, 0.8T) Top Schematic C6=10 nF R6=1.1 kW C7=1 mF VDD R5=9.1 kW C1=1.5 pF R4=33 W R3=33 W ASL563 L1=3.3 nH R1=8.2 kW L2=15 nH R2=1.2 kW C5=1 pF RF OUT *P2 *P1 VDD C2=1 mF L4=3.3 nH m m 7 L3=15 nH 7mm C4=10 pF Bottom C3=10nF RF IN Note: 1) the length of the strip line P1 and P2 are given as below at the PCB with Er = 4.5 and T = 0.8 mm. *P1 Length: 2.5 mm, Width: 0.3 mm *P2 Length: 0.3 mm, Width: 0.3 mm 2) Gain and S11 are in trade-off and varied with the length of P1 and P2 S-parameters & Noise Figure 30 20 S21 S22 S11 S(2,2) S(1,1) S - parameter [dB] 10 0 -10 S22 -20 S11 -30 S12 -40 2100 2200 2300 2400 2500 2600 2700 2800 freq (2.100GHz to 2.800GHz) Frequency [MHz] 5 1.5 1.4 4 1.3 3 Noise Figure Stability Factor 1.2 2 1.1 1.0 0.9 0.8 1 0.7 0.6 0 0 500 1000 1500 2000 2500 3000 3500 0.5 2100 2200 2300 Frequency (MHz) 22/22 2400 2500 2600 2700 2800 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 August 2011