Features • Serial Peripheral Interface (SPI) Compatible • Supports SPI Modes 0 (0,0) and 3 (1,1) • Low-voltage and Standard-voltage Operation • • • • • • • • – 2.7 (VCC = 2.7V to 5.5V) – 1.8 (VCC = 1.8V to 5.5V) 3.0 MHz Clock Rate (5V) 32-byte Page Mode Block Write Protection – Protect 1/4, 1/2, or Entire Array Write Protect (WP) Pin and Write Disable Instructions for both Hardware and Software Data Protection Self-timed Write Cycle (5 ms Typical) High-reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years Automotive Grade Devices Available 8-lead PDIP, 8-lead JEDEC SOIC and 14-lead TSSOP Packages Description The AT25080/160/320/640 provides 8192/16384/32768/65536 bits of serial electrically-e ra sa ble pro gramma ble re ad on ly memo r y ( EEPROM ) or ga nize d a s 1024/2048/4096/8192 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT25080/160/320/640 is available in space saving 8-lead PDIP, 8lead JEDEC SOIC and 14-lead TSSOP packages. The AT25080/160/320/640 is enabled through the Chip Select pin (CS) and accessed via a 3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and Serial Clock (SCK). All programming cycles are completely self-timed, and no separate ERASE cycle is required before WRITE. Function CS Chip Select SCK Serial Data Clock SI Serial Data Input SO Serial Data Output GND Ground VCC Power Supply WP Write Protect HOLD Suspends Serial Input NC No Connect DC Don’t Connect AT25080 AT25160 AT25320 AT25640 8-lead PDIP Pin Configuration Pin Name SPI Serial EEPROMs 8K (1024 x 8) 16K (2048 x 8) 32K (4096 x 8) 64K (8192 x 8) CS SO WP GND 1 2 3 4 8 7 6 5 VCC HOLD SCK SI 8-lead SOIC CS SO WP GND 1 2 3 4 8 7 6 5 VCC HOLD SCK SI 14-lead TSSOP CS SO NC NC NC WP GND 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC HOLD NC NC NC SCK SI 0675M–SEEPR–9/03 1 BLOCK WRITE protection is enabled by programming the status register with one of four blocks of write protection. Separate program enable and program disable instructions are provided for additional data protection. Hardware data protection is provided via the WP pin to protect against inadvertent write attempts to the status register. The HOLD pin may be used to suspend any serial communication without resetting the serial sequence. Absolute Maximum Ratings* Operating Temperature.................................. -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .....................................-1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Output Current........................................................ 5.0 mA Block Diagram 2 AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +5.0V (unless otherwise noted). Symbol Test Conditions Max Units Conditions COUT Output Capacitance (SO) 8 pF VOUT = 0V CIN Input Capacitance(CS, SCK, SI, WP, HOLD) 6 pF VIN = 0V Note: 1. This parameter is characterized and is not 100% tested. DC Characteristics(1) Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, VCC = +1.8V to +5.5V (unless otherwise noted). Symbol Parameter VCC1 Supply Voltage VCC2 Max Units 1.8 3.6 V Supply Voltage 2.7 5.5 V VCC3 Supply Voltage 4.5 5.5 V ICC1 Supply Current VCC = 5.0V at 1 MHz, SO = Open, Read 3.0 mA ICC2 Supply Current VCC = 5.0V at 2 MHz, SO = Open, Read, Write 5.0 mA ISB1 Standby Current VCC = 1.8V, CS = VCC 0.1 1.0 µA ISB2 Standby Current VCC = 2.7V, CS = VCC 0.2 2.0 µA ISB3 Standby Current VCC = 5.0V, CS = VCC 2.0 5.0 µA IIL Input Leakage VIN = 0V to VCC -3.0 Output Leakage VIN = 0V to VCC, TAC = 0°C to 70°C -3.0 3.0 µA IOL VIL Test Condition Min Typ µA (1) Input Low-voltage -0.6 VCC x 0.3 V (1) Input High-voltage VCC x 0.7 VCC + 0.5 V 0.4 V VIH VOL1 Output Low-voltage VOH1 Output High-voltage VOL2 Output Low-voltage VOH2 Output High-voltage Note: 4.5V ≤ VCC ≤ 5.5V 1.8V ≤ VCC ≤ 3.6V IOL = 3.0 mA IOH = -1.6 mA VCC - 0.8 IOL = 0.15 mA IOH = -100 µA V 0.2 VCC - 0.2 V V 1. VIL min and VIH max are reference only and are not tested. 3 0675M–SEEPR–9/03 AC Characteristics Applicable over recommended operating range from TAI = -40°C to +85°C, VCC = As Specified, CL = 1 TTL Gate and 100 pF (unless otherwise noted). Symbol Parameter Voltage Min Max Units fSCK SCK Clock Frequency 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 0 0 0 3.0 2.1 0.5 MHz tRI Input Rise Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 2 2 2 µs tFI Input Fall Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 2 2 2 µs tWH SCK High Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 133 200 800 ns tWL SCK Low Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 133 200 800 ns tCS CS High Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 250 250 1000 ns tCSS CS Setup Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 250 250 1000 ns tCSH CS Hold Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 250 250 1000 ns tSU Data In Setup Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 50 50 100 ns tH Data In Hold Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 50 50 100 ns tHD Hold Setup Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 100 100 400 tCD Hold Hold Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 200 200 400 tV Output Valid 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 0 0 0 tHO Output Hold Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 0 0 0 4 ns 133 200 800 ns ns AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 AC Characteristics (Continued) Applicable over recommended operating range from TAI = -40°C to +85°C, VCC = As Specified, CL = 1 TTL Gate and 100 pF (unless otherwise noted). Symbol Parameter Voltage Min Max Units tLZ Hold to Output Low Z 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 0 0 0 100 100 100 ns tHZ Hold to Output High Z 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 100 100 100 ns tDIS Output Disable Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 250 250 1000 ns tWC Write Cycle Time 4.5 - 5.5 2.7 - 5.5 1.8 - 5.5 5 10 20 ms Endurance(1) 5.0V, 25°C, Page Mode Note: 1M Write Cycles 1. This parameter is characterized and is not 100% tested. 5 0675M–SEEPR–9/03 Serial Interface Description MASTER: The device that generates the serial clock. SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25080/160/320/640 always operates as a slave. TRANSMITTER/RECEIVER: The AT25080/160/320/640 has separate pins designated for data transmission (SO) and reception (SI). MSB: The Most Significant Bit (MSB) is the first bit transmitted and received. SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be received. This byte contains the op-code that defines the operations to be performed. INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the AT25080/160/320/640, and the serial output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This will reinitialize the serial communication. CHIP SELECT: The AT25080/160/320/640 is selected when the CS pin is low. When the device is not selected, data will not be accepted via the SI pin, and the serial output pin (SO) will remain in a high impedance state. HO LD: The HOL D pin is use d in conjunctio n with th e CS pin to select th e AT25080/160/320/640. When the device is selected and a serial sequence is underway, HOLD can be used to pause the serial communication with the master device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may still toggle during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state. WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when held high. When the WP pin is brought low and WPEN bit is “1”, all write operations to the status register are inhibited. WP going low while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated, WP going low will have no effect on any write operation to the status register. The WP pin function is blocked when the WPEN bit in the status register is “0”. This will allow the user to install the AT25080/160/320/640 in a system with the WP pin tied to ground and still be able to write to the status register. All WP pin functions are enabled when the WPEN bit is set to “1”. 6 AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 SPI Serial Interface 7 0675M–SEEPR–9/03 Functional Description The AT25080/160/320/640 is designed to interface directly with the synchronous serial peripheral interface (SPI) of the 6805 and 68HC11 series of microcontrollers. The AT25080/160/320/640 utilizes an 8-bit instruction register. The list of instructions and their operation codes are contained in Table 1. All instructions, addresses, and data are transferred with the MSB first and start with a high-to-low CS transition. Table 1. Instruction Set for the AT25080/160/320/640 Instruction Name Instruction Format Operation WREN 0000 X110 Set Write Enable Latch WRDI 0000 X100 Reset Write Enable Latch RDSR 0000 X101 Read Status Register WRSR 0000 X001 Write Status Register READ 0000 X011 Read Data from Memory Array WRITE 0000 X010 Write Data to Memory Array WRITE ENABLE (WREN): The device will power-up in the write disable state when V CC is applied. All programming instructions must therefore be preceded by a Write Enable instruction. WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write Disable instruction disables all programming modes. The WRDI instruction is independent of the status of the WP pin. READ STATUS REGISTER (RDSR): The Read Status Register instruction provides access to the status register. The READY/BUSY and Write Enable status of the device can be determined by the RDSR instruction. Similarly, the Block Write Protection bits indicate the extent of protection employed. These bits are set by using the WRSR instruction. Table 2. Status Register Format Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WPEN X X X BP1 BP0 WEN RDY Table 3. Read Status Register Bit Definition Bit Definition Bit 0 (RDY) Bit 0 = 0 (RDY) indicates the device is READY. Bit 0 = 1 indicates the write cycle is in progress. Bit 1 (WEN) Bit 1= 0 indicates the device is not WRITE ENABLED. Bit 1 = 1 indicates the device is WRITE ENABLED. Bit 2 (BP0) See Table 4 on page 9. Bit 3 (BP1) See Table 4 on page 9. Bits 4 - 6 are 0s when device is not in an internal write cycle. Bit 7 (WPEN) See Table 5 on page 9. Bits 0 - 7 are 1s during an internal write cycle. 8 AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select one of four levels of protection. The AT25080/160/320/640 is divided into four array segments. One quarter (1/4), one half (1/2), or all of the memory segments can be protected. Any of the data within any selected segment will therefore be READ only. The block write protection levels and corresponding status register control bits are shown in Table 4. The three bits, BP0, BP1, and WPEN are nonvolatile cells that have the same properties and functions as the regular memory cells (e.g. WREN, tWC, RDSR). Table 4. Block Write Protect Bits Status Register Bits Array Addresses Protected BP1 BP0 AT25080 AT25160 AT25320 AT25640 0 0 0 None None None None 1(1/4) 0 1 0300 -03FF 0600 -07FF 0C00 -0FFF 1800 -1FFF 2(1/2) 1 0 0200 -03FF 0400 -07FF 0800 -0FFF 1000 -1FFF 3(All) 1 1 0000 -03FF 0000 -07FF 0000 -0FFF 0000 -1FFF Level The WRSR instruction also allows the user to enable or disable the write protect (WP) pin through the use of the Write Protect Enable (WPEN) bit. Hardware write protection is enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is disabled when either the WP pin is high or the WPEN bit is “0”. When the device is hardware write protected, writes to the Status Register, including the Block Protect bits and the WPEN bit, and the blockprotected sections in the memory array are disabled. Writes are only allowed to sections of the memory which are not block-protected. NOTE: When the WPEN bit is hardware write protected, it cannot be changed back to “0”, as long as the WP pin is held low. Table 5. WPEN Operation WPEN WP WEN Protected Blocks Unprotected Blocks Status Register 0 X 0 Protected Protected Protected 0 X 1 Protected Writable Writable 1 Low 0 Protected Protected Protected 1 Low 1 Protected Writable Protected X High 0 Protected Protected Protected X High 1 Protected Writable Writable 9 0675M–SEEPR–9/03 READ SEQUENCE (READ): Reading the AT25080/160/320/640 via the SO (Serial Output) pin requires the following sequence. After the CS line is pulled low to select a device, the READ op-code is transmitted via the SI line followed by the byte address to be read (A15 - A0, Refer to Table 6). Upon completion, any data on the SI line will be ignored. The data (D7 - D0) at the specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line should be driven high after the data comes out. The READ sequence can be continued since the byte address is automatically incremented and data will continue to be shifted out. When the highest address is reached, the address counter will roll over to the lowest address allowing the entire memory to be read in one continuous READ cycle. WRITE SEQUENCE (WRITE): In order to program the AT25080/160/320/640, two separate instructions must be executed. First, the device must be write enabled via the Write Enable (WREN) Instruction. Then a Write (WRITE) Instruction may be executed. Also, the address of the memory location(s) to be programmed must be outside the protected address field location selected by the Block Write Protection Level. During an internal write cycle, all commands will be ignored except the RDSR instruction. A Write Instruction requires the following sequence. After the CS line is pulled low to select the device, the WRITE op-code is transmitted via the SI line followed by the byte address (A15 - A0) and the data (D7 - D0) to be programmed (Refer to Table 6). Programming will start after the CS pin is brought high. (The LOW-to-High transition of the CS pin must occur during the SCK low-time immediately after clocking in the D0 (LSB) data bit. The READY/BUSY status of the device can be determined by initiating a READ STATUS REGISTER (RDSR) Instruction. If Bit 0 = 1, the WRITE cycle is still in progress. If Bit 0 = 0, the WRITE cycle has ended. Only the READ STATUS REGISTER instruction is enabled during the WRITE programming cycle. The AT25080/160/320/640 is capable of a 32-byte PAGE WRITE operation. After each byte of data is received, the five low order address bits are internally incremented by one; the high order bits of the address will remain constant. If more than 32 bytes of data are transmitted, the address counter will roll over and the previously written data will be overwritten. The AT25080/160/320/640 is automatically returned to the write disable state at the completion of a WRITE cycle. NOTE: If the device is not Write enabled (WREN), the device will ignore the Write instruction and will return to the standby state, when CS is brought high. A new CS falling edge is required to re-initiate the serial communication. Table 6. Address Key 10 Address AT25080 AT25160 AT25320 AT25640 AN A9 - A0 A10 - A0 A11 - A0 A12 - A0 Don't Care Bits A15 - A10 A15 - A11 A15 - A 12 A15 - A13 AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 Timing Diagrams Synchronous Data Timing (for Mode 0) t CS VIH CS VIL t CSH t CSS VIH t WH SCK t WL VIL tH t SU VIH SI VALID IN VIL tV VOH SO HI-Z t HO t DIS HI-Z VOL WREN Timing WRDI Timing 11 0675M–SEEPR–9/03 RDSR Timing CS 0 1 2 3 4 5 6 7 8 9 7 6 10 11 12 13 14 15 2 1 0 SCK INSTRUCTION SI SO DATA OUT HIGH IMPEDANCE 5 4 3 MSB WRSR Timing CS 0 1 2 3 4 5 6 7 8 9 10 7 6 5 11 12 13 14 15 DATA IN 4 3 2 1 0 SCK SI SO INSTRUCTION HIGH IMPEDANCE READ Timing CS 0 1 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 30 31 SCK SI SO 12 INSTRUCTION HIGH IMPEDANCE BYTE ADDRESS 15 14 13 ... 3 2 1 0 DATA OUT 7 6 5 4 3 2 1 0 MSB AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 WRITE Timing CS 0 1 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 30 31 SCK SI SO BYTE ADDRESS DATA IN ... 15 14 13 3 2 1 0 7 6 5 4 3 2 1 0 INSTRUCTION HIGH IMPEDANCE HOLD Timing CS tCD tCD SCK t HD t HD HO LD t HZ SO t LZ 13 0675M–SEEPR–9/03 AT25080 Ordering Information Ordering Code Package AT25080-10PI-2.7 AT25080N-10SI-2.7 AT25080T1-10TI-2.7 8P3 8S1 14A2 Industrial (-40°C to 85°C) AT25080-10PI-1.8 AT25080N-10SI-1.8 AT25080T1-10TI-1.8 8P3 8S1 14A2 Industrial (-40°C to 85°C) Note: Operation Range For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 14A2 14-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V) 14 AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 AT25160 Ordering Information Ordering Code Package AT25160-10PI-2.7 AT25160N-10SI-2.7 AT25160T1-10TI-2.7 8P3 8S1 14A2 Industrial (-40°C to 85°C) AT25160-10PI-1.8 AT25160N-10SI-1.8 AT25160T1-10TI-1.8 8P3 8S1 14A2 Industrial (-40°C to 85°C) Note: Operation Range For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 14A2 14-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V) 15 0675M–SEEPR–9/03 AT25320 Ordering Information Ordering Code Package AT25320-10PI-2.7 AT25320N-10SI-2.7 AT25320T1-10TI-2.7 8P3 8S1 14A2 Note: Operation Range Industrial (-40°C to 85°C) For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 14A2 14-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 16 Low Voltage (2.7V to 5.5V) AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 AT25640 Ordering Information Ordering Code Package AT25640-10PI-2.7 AT25640N-10SI-2.7 AT25640T1-10TI-2.7 8P3 8S1 14A2 Industrial (-40°C to 85°C) AT25640-10PI-1.8 AT25640N-10SI-1.8 AT25640T1-10TI-1.8 8P3 8S1 14A2 Industrial (-40°C to 85°C) Note: Operation Range For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 14A2 14-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V) 17 0675M–SEEPR–9/03 Packaging Information 8P3 – PDIP E 1 E1 N Top View c eA End View COMMON DIMENSIONS (Unit of Measure = inches) D e D1 A2 A SYMBOL MIN NOM A b2 b3 b 4 PLCS Side View Notes: L MAX 0.210 NOTE 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 D1 0.005 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 5 3 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.1 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. 6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 01/09/02 R 18 2325 Orchard Parkway San Jose, CA 95131 TITLE 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) DRAWING NO. REV. 8P3 B AT25080/160/320/640 0675M–SEEPR–9/03 AT25080/160/320/640 8S1 – JEDEC SOIC C 1 E E1 L N ∅ Top View End View e B COMMON DIMENSIONS (Unit of Measure = mm) A SYMBOL A1 D Side View MIN NOM MAX A 1.35 – 1.75 A1 0.10 – 0.25 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e NOTE 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 10/7/03 R 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. 8S1 REV. B 19 0675M–SEEPR–9/03 14A2 – TSSOP b L L1 E1 E End View e COMMON DIMENSIONS (Unit of Measure = mm) Top View SYMBOL D D A MIN 4.90 E A2 E1 R 20 NOTE 5.00 5.10 2, 5 4.50 3, 5 4.40 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 L L1 Notes: MAX 6.40 BSC 4.30 e Side View NOM 0.45 0.60 TITLE 14A2,14-lead (4.4 x 5 mm Body), 0.65 Pitch, Thin Shrink Small Outline Package (TSSOP) 0.75 1.00 REF 1. This drawing is for general information only. Please refer to JEDEC Drawing MO-153, Variation AB-1, for additional information. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 2325 Orchard Parkway San Jose, CA 95131 4 0.65 BSC 12/28/01 DRAWING NO. 14A2 REV. A AT25080/160/320/640 0675M–SEEPR–9/03 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. © Atmel Corporation 2003. All rights reserved. Atmel® and combinations thereof, are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others. Printed on recycled paper. 0675M–SEEPR–9/03 xM