AT27BV4096 Features • • • • • • • • • • Fast Read Access Time - 120 ns Dual Voltage Range Operation Unregulated Battery Power Supply Range, 2.7V to 3.6V or Standard 5V ± 10% Supply Range Pin Compatible with JEDEC Standard AT27C4096 Low Power CMOS Operation 20 µA max. (less than 1 µA typical) Standby for VCC = 3.6V 29 mW max. Active at 5 MHz for VCC = 3.6V JEDEC Standard Surface Mount Packages 44-Lead PLCC 40-Lead TSOP (10 x 14mm) High Reliability CMOS Technology 2,000V ESD Protection 200 mA Latchup Immunity Rapid Programming algorithm - 100 µs/word (typical) CMOS and TTL Compatible Inputs and Outputs JEDEC Standard for LVTTL and LVBO Integrated Product Identification Code Commercial and Industrial Temperature Ranges Description The AT27BV4096 is a high performance, low power, low voltage 4,194,304 bit onetime programmable read only memory (OTP EPROM) organized as 256K by 16 bits. It requires only one supply in the range of 2.7V to 3.6V in normal read mode operation. The by-16 organization makes this part ideal for portable and handheld 16 and 32 bit microprocessor based systems using either regulated or unregulated battery power. (continued) 4 Megabit (256K x 16) Unregulated Battery-Voltage High Speed OTP CMOS EPROM Pin Configurations Pin Name Function A0 - A17 Addresses O0 - O15 Outputs CE Chip Enable OE Output Enable NC No Connect AT27BV4096 Note: Both GND pins must be connected. PLCC Top View Note: 1. PLCC package pins 1 and 23 are DON’T CONNECT. TSOP Top View Type 1 0640A 3-63 Description (Continued) System Considerations Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3V supply. At VCC = 2.7V, any word can be accessed in less than 120 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3 V , t h e AT27BV4096 consumes less than one fifth the power of a standard 5V EPROM. Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV4096 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV4096 is available in industry standard JEDEC-approved one-time programmable (OTP) plastic PLCC and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. The AT27BV4096 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts. Atmel’s AT27BV4096 has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/word. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27BV4096 programs exactly the same way as a standard 5V AT27C4096 and uses the same programming equipment. 3-64 AT27BV4096 AT27BV4096 Absolute Maximum Ratings* Block Diagram Temperature Under Bias ................ -55°C to +125°C Storage Temperature...................... -65°C to +150°C Voltage on Any Pin with Respect to Ground......................... -2.0V to +7.0V (1) Voltage on A9 with Respect to Ground ...................... -2.0V to +14.0V (1) VPP Supply Voltage with Respect to Ground....................... -2.0V to +14.0V (1) *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V dc which may overshoot to +7.0V for pulses of less than 20 ns. Operating Modes CE Mode \ Pin Read (2) VIL Output Disable (2) X OE VIL VIH Ai VPP Ai (1) X X X (5) VCC Outputs VCC (2) DOUT VCC (2) High Z VCC (2) High Z Standby (2) VIH X X X Rapid Program (3) VIL VIH Ai VPP VCC (3) VPP VCC (3) DOUT VPP VCC (3) High Z VCC VCC (3) PGM Verify (3) PGM Inhibit (3) VIH VIH VIL Ai VIH X DIN (4) Product Identification (3, 5) VIL VIL A9 = VH A0 = VIH or VIL A1 - A17 = VIL Notes: 1. X can be VIL or VIH. 2. Read, output disable, and standby modes require, 2.7V ≤ VCC ≤ 3.6V, or 4.5V ≤ VCC ≤ 5.5V. 3. Refer to Programming Characteristics. Programming modes require VCC = 6.5V. Identification Code 4. VH = 12.0 ± 0.5V. 5. Two identifier words may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low (VIL) to select the Manufacturer’s Identification word and high (VIH) to select the Device Code word. 3-65 DC and AC Operating Conditions for Read Operation AT27BV4096 Operating Temperature (Case) -12 0°C - 70°C -15 0°C - 70°C -40°C - 85°C -40°C - 85°C 2.7V - 3.6V 2.7V - 3.6V 5V ± 10% 5V ± 10% Com. Ind. VCC Power Supply = Preliminary Information DC and Operating Characteristics for Read Operation Symbol Parameter Condition Min Max Units VCC = 2.7V to 3.6V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC ±1 µA Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 20 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 100 µA 8 mA VPP (1) Read/Standby Current VCC (1) Standby Current ISB ICC VCC Active Current VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage f = 5 MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V VCC = 3.0 to 3.6V -0.6 0.8 V VCC = 2.7 to 3.6V -0.6 0.2 x VCC V VCC = 3.0 to 3.6V 2.0 VCC + 0.5 V 0.7 x VCC VCC + 0.5 V VCC = 2.7 to 3.6V IOL = 2.0 mA 0.4 V IOL = 100 µA 0.2 V IOL = 20 µA 0.1 V IOH = -2.0 mA 2.4 V IOH = -100 µA VCC - 0.2 V IOH = -20 µA VCC - 0.1 V VCC = 4.5V to 5.5V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC ±1 µA Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 100 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA f = 5 MHz, IOUT = 0 mA, CE = VIL 40 mA VPP (1) Read/Standby Current ISB VCC (1) Standby Current ICC VCC Active Current VIL Input Low Voltage -0.6 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage IOL = 2.1 mA 0.4 V VOH Output High Voltage IOH = -400 µA Notes: 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP. 3-66 AT27BV4096 2.4 V 2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP. AT27BV4096 AC Characteristics for Read Operation (VCC = 2.7V to 3.6V and 4.5V to 5.5V) AT27BV4096 -12 Symbol Parameter Condition tACC (3) Address to Output Delay CE = OE = VIL tCE (2) Min -15 Max Units 120 150 ns Max Min CE to Output Delay OE = VIL 120 150 ns tOE (2, 3) OE to Output Delay CE = VIL 35 50 ns tDF (4, 5) OE or CE High to Output Float, whichever occurred first 30 40 ns tOH Output Hold from Address, CE or OE, whichever occurred first 0 Notes: 2, 3, 4, 5. - see AC Waveforms for Read Operation. AC Waveforms for Read Operation 0 ns = Preliminary Information (1) Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 6. When reading a 27BV4096, a 0.1 µF capacitor is required across VCC and ground to supress spurious voltage transients. 3-67 Input Test Waveforms and Measurement Levels Output Test Load tR, tF < 20 ns (10% to 90%) Note: CL = 100 pF including jig capacitance. Pin Capacitance (f = 1 MHz T = 25°C) (1) Typ Max Units CIN 4 10 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 3-68 Conditions 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV4096 AT27BV4096 Programming Waveforms (1) Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 3. When programming the AT27BV4096 a 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage transients. DC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL, VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 µA ICC2 VCC Supply Current (Program and Verify) IPP2 VPP Supply Current VID A9 Product Identification Voltage Max Units ±10 µA -0.6 0.8 V 2.0 VCC + 0.1 V 0.4 V Min 2.4 CE = VIL 11.5 V 50 mA 30 mA 12.5 V 3-69 AC Programming Characteristics Rapid Programming Algorithm TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V A 50 µs CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 50 µs CE pulse without verification. Then a verification / reprogramming loop is executed for each address. In the event a word fails to pass verification, up to 10 successive 50 µs pulses are applied with a verification after each pulse. If the word fails to verify after 10 pulses have been applied, the part is considered failed. After the word verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All words are read again and compared with the original data to determine if the device passes or fails. SymTest (1) bol Parameter Conditions* Limits Min Max Units tAS Address Setup Time 2 µs tCES CE Setup Time 2 µs tOES OE Setup Time 2 µs tDS Data Setup Time 2 µs tAH Address Hold Time 0 µs tDH Data Hold Time 2 µs tDFP OE High to Output Float Delay (2) 0 tVPS VPP Setup Time 2 µs tVCS VCC Setup Time 2 µs tPW PGM Program Pulse Width (3) tOE Data Valid from OE tPRT VPP Pulse Rise Time During Programming 47.5 130 ns 52.5 µs 150 ns 50 ns *AC Conditions of Test: Input Rise and Fall Times (10% to 90%)..............20 ns Input Pulse Levels.................................. 0.45V to 2.4V Input Timing Reference Level ..................0.8V to 2.0V Output Timing Reference Level ...............0.8V to 2.0V Notes: 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven — see timing diagram. 3. Program Pulse width tolerance is 50 µsec ± 5%. Atmel’s 27BV4096 Integrated Product Identification Code (1) Pins Codes Manufacturer Device Type Note: 3-70 A0 015-08 O7 O6 O5 O4 O3 O2 O1 O0 0 1 0 0 0 1 0 1 0 1 1 1 1 1 0 1 Hex Data 1 0 001E 0 0 00F4 1. The AT27BV4096 has the same Product Identification Code as the AT27C4096. Both are programming compatible. AT27BV4096 AT27BV4096 Ordering Information ICC (mA) tACC (ns) Active Standby 120 8 150 Ordering Code Package Operation Range 0.02 AT27BV4096-12JC AT27BV4096-12VC 44J 40V Commercial (0°C to 70°C) 8 0.02 AT27BV4096-12JI AT27BV4096-12VI 44J 40V Industrial (-40°C to 85°C) 8 0.02 AT27BV4096-15JC AT27BV4096-15VC 44J 40V Commercial (0°C to 70°C) 8 0.02 AT27BV4096-15JI AT27BV4096-15VI 44J 40V Industrial (-40°C to 85°C) = Preliminary Information Package Type 44J 44 Lead, Plastic J-Leaded Chip Carrier (PLCC) 40V 40 Lead, Plastic Thin Small Outline Package (TSOP) 10 x 14 mm 3-71