Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4Vdc –5.5Vdc input; 0.75Vdc to 3.63Vdc Output;10A Output Current RoHS Compliant EZ-SEQUENCETM Features Compliant to RoHS EU Directive 2002/95/EC (-Z versions) Compliant to ROHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) Flexible output voltage sequencing EZTM SEQUENCE Delivers up to 10A output current High efficiency – 95% at 3.3V full load (VIN = 5.0V) Small size and low profile: 33.0 mm x 13.5 mm x 8.28 mm (1.30 in x 0.53 in x 0.326 in) Applications Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Low output ripple and noise High Reliability: o Calculated MTBF = 15.7M hours at 25 C Full-load Constant switching frequency (300 kHz) Output voltage programmable from 0.75 Vdc to 3.63Vdc via external resistor Networking equipment Line Regulation: 0.3% (typical) Enterprise Networks Load Regulation: 0.4% (typical) Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications Temperature Regulation: 0.4 % (typical) Remote On/Off Remote sense Output overcurrent protection (non-latching) Wide operating temperature range (-40°C to 85°C) UL* 60950-1Recognized, CSA† C22.2 No. 60950-103 Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Description TM Austin Lynx II SMT (surface mount technology) power modules are non-isolated DC-DC converters that can deliver up to 10A of output current with full load efficiency of 95% at 3.3V output. These modules provide a precisely regulated output voltage programmable via an external resistor from 0.75Vdc to 3.63Vdc over a wide range of input voltage (VIN = 2.4 – 5.5Vdc). The Austin LynxTM II series has a sequencing feature, EZSEQUENCETM that enable designers to implement various types of output voltage sequencing when powering multiple voltages on a board. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ Document No: DS03-105 ver. 1.03 PDF name: lynx_II_smt_ds.pdf Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 5.8 Vdc Sequencing voltage All Vseq -0.3 VIN,max Vdc Operating Ambient Temperature All TA -40 85 °C All Tstg -55 125 °C Input Voltage Continuous (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit 2.4 ⎯ 5.5 Vdc 10 Adc Operating Input Voltage Vo ≤ VIN - 0.5 VIN Maximum Input Current All IIN,max Vo = 0.75Vdc IIN,No load 25 mA Vo = 3.3Vdc IIN,No load 30 mA All IIN,stand-by 1.5 mA Inrush Transient All It Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test Configurations) All 100 mAp-p Input Ripple Rejection (120Hz) All 30 dB (VIN=2.4V to 5.5V, IO=IO, max ) Input No Load Current (VIN = 5.0Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.0Vdc, module disabled) 2 0.1 2 As CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a 15A, time-delay fuse (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. LINEAGE POWER 2 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -2.0 VO, set +2.0 % VO, set All VO, set -3% ⎯ +3% % VO, set All VO 0.7525 3.63 Vdc (VIN=IN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All ⎯ 0.3 ⎯ % VO, set Load (IO=IO, min to IO, max) All ⎯ 0.4 ⎯ % VO, set Temperature (Tref=TA, min to TA, max) All ⎯ 0.4 ⎯ % VO, set RMS (5Hz to 20MHz bandwidth) All ⎯ 8 15 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ 25 50 mVpk-pk μF Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1μF ceramic//10μFtantalum capacitors) External Capacitance ESR ≥ 1 mΩ All CO, max ⎯ ⎯ 1000 ⎯ 5000 μF 10 Adc All CO, max ⎯ Output Current All Io 0 Output Current Limit Inception (Hiccup Mode ) All IO, lim ⎯ 200 ⎯ % Io All IO, s/c ⎯ 3.0 ⎯ Adc VO,set = 0.75Vdc η 81.5 % VIN= VIN, nom, TA=25°C VO, set = 1.2Vdc η 87.0 % IO=IO, max , VO= VO,set VO,set = 1.5Vdc η 89.0 % VO,set = 1.8Vdc η 90.0 % VO,set = 2.5Vdc η 93.0 % ESR ≥ 10 mΩ (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency Switching Frequency VO,set = 3.3Vdc η All fsw ⎯ 94.0 300 ⎯ kHz % All Vpk ⎯ 250 ⎯ mV Dynamic Load Response (dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) Load Change from Io= 50% to 100% of Io,max; 1μF ceramic// 10 μF tantalum Peak Deviation Settling Time (Vo<10% peak deviation) All ts ⎯ 50 ⎯ μs (dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) Load Change from Io= 100% to 50%of Io,max: 1μF ceramic// 10 μF tantalum All Vpk ⎯ 250 ⎯ mV All ts ⎯ 50 ⎯ μs Peak Deviation Settling Time (Vo<10% peak deviation) LINEAGE POWER 3 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit All Vpk ⎯ 60 ⎯ mV Dynamic Load Response (dIo/dt=2.5A/μs; V VIN = VIN, nom; TA=25°C) Load Change from Io= 50% to 100% of Io,max; Co = 2x150 μF polymer capacitors Peak Deviation Settling Time (Vo<10% peak deviation) All ts ⎯ 100 ⎯ μs (dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) Load Change from Io= 100% to 50%of Io,max: Co = 2x150 μF polymer capacitors Peak Deviation All Vpk ⎯ 60 ⎯ mV Settling Time (Vo<10% peak deviation) All ts ⎯ 100 ⎯ μs General Specifications Parameter Min Calculated MTBF (IO=IO, max, TA=25°C) Weight LINEAGE POWER Typ Max 15,726,300 ⎯ 2.8 (0.1) Unit Hours ⎯ g (oz.) 4 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit On/Off Signal interface Device code with Suffix “4” – Positive logic (On/Off is open collector/drain logic input; Signal referenced to GND - See feature description section) Input High Voltage (Module ON) All VIH ― ― VIN, max V Input High Current All IIH ― ― 10 μA Input Low Voltage (Module OFF) All VIL -0.2 ― 0.3 V Input Low Current All IIL ― 0.2 1 mA Input High Voltage (Module OFF) All VIH 1.5 Input High Current All IIH Input Low Voltage (Module ON) All VIL Input low Current All IIL Case 1: On/Off input is set to Logic Low (Module ON) and then input power is applied (delay from instant at which VIN =VIN, min until Vo=10% of Vo,set) All Tdelay Case 2: Input power is applied for at least one second and then the On/Off input is set to logic Low (delay from instant at which Von/Off=0.3V until Vo=10% of Vo, set) All Output voltage Rise time (time for Vo to rise from 10% of Vo,set to 90% of Vo, set) Sequencing Delay time All Delay from VIN, min to application of voltage on SEQ pin Device Code with no suffix – Negative Logic (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) -0.2 ― VIN,max Vdc 0.2 1 mA ― 0.3 Vdc ― 10 μA ― 3.9 ― msec Tdelay ― 3.9 ― msec Trise ― 4.2 8.5 msec All TsEQ-delay 10 (Power-Up: 2V/ms) All (Power-Down: 1V/ms) All |VSEQ –Vo | |VSEQ –Vo | Turn-On Delay and Rise Times o (IO=IO, max , VIN = VIN, nom, TA = 25 C, ) Tracking Accuracy (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) msec 100 200 mV 200 400 mV ― 1 % VO, set ― ― 0.5 V ⎯ 125 ⎯ °C Output voltage overshoot – Startup o IO= IO, max; VIN = 3.0 to 5.5Vdc, TA = 25 C Remote Sense Range Overtemperature Protection All Tref (See Thermal Consideration section) Input Undervoltage Lockout Turn-on Threshold All 2.2 V Turn-off Threshold All 2.0 V LINEAGE POWER 5 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Characteristic Curves The following figures provide typical characteristics for the Austin LynxTM II SMT modules at 25ºC. 90 96 VIN = 3.0V 93 87 EFFICIENCY, (η) EFFICIENCY, (η) 90 84 81 78 VIN = 5.0V 75 VIN = 5.5V 72 87 84 81 VIN = 3.0V 78 VIN = 5.0V 75 VIN = 5.5V 72 0 2.5 5 7.5 10 0 OUTPUT CURRENT, IO (A) 2.5 5 7.5 10 OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current (Vout = 0.75Vdc). Figure 4. Converter Efficiency versus Output Current (Vout = 1.8Vdc). 93 100 97 90 94 EFFICIENCY, (η) EFFICIENCY, (η) 87 84 81 VIN = 3.0V 78 VIN = 5.0V 75 85 82 VIN = 3.0V 79 VIN = 5.0V 76 VIN = 5.5V 72 VIN = 5.5V 73 0 2.5 5 7.5 10 OUTPUT CURRENT, IO (A) Figure 2. Converter Efficiency versus Output Current (Vout = 1.2Vdc). 0 2.5 5 7.5 10 OUTPUT CURRENT, IO (A) Figure 5. Converter Efficiency versus Output Current (Vout = 2.5Vdc). 100 94 91 97 88 94 EFFICIENCY, (η) EFFICIENCY, (η) 91 88 85 82 79 VIN = 3.0V 76 VIN = 5.0V 73 5 7.5 OUTPUT CURRENT, IO (A) Figure3. Converter Efficiency versus Output Current (Vout = 1.5Vdc). LINEAGE POWER VIN = 4.5V VIN = 5.0V 79 76 70 2.5 85 82 VIN = 5.5V VIN = 5.5V 0 91 88 10 0 2.5 5 7.5 10 OUTPUT CURRENT, IO (A) Figure 6. Converter Efficiency versus Output Current (Vout = 3.3Vdc). 6 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Characteristic Curves (continued) The following figures provide typical characteristics for the Austin LynxTM II SMT modules at 25ºC. 10 3 2 1 0 0.5 1.5 2.5 3.5 4.5 INPUT VOLTAGE, VIN (V) VO (V) (20mV/div) OUTPUT VOLTAGE Figure 7. Input voltage vs. Input Current (Vo = 2.5Vdc). VO (V) (200mV/div) TIME, t (10μs/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3Vdc). TIME, t (2μs/div) Figure 9. Typical Output Ripple and Noise (Vin = 5.0V dc, Vo = 3.3 Vdc, Io=10A). LINEAGE POWER VO (V) (50mV/div) IO (A) (5A/div) VO (V) (20mV/div) Figure 11. Transient Response to Dynamic Load Change from 100% to 50% of full load (Vo = 3.3 Vdc). OUTPUT CURRENT, OUTPUT VOLTAGE TIME, t (10μs/div) Figure 8. Typical Output Ripple and Noise (Vin = 5.0V dc, Vo = 0.75, Vdc, Io=10A). OUTPUT VOLTAGE TIME, t (2μs/div) 5.5 IO (A) (5A/div) 5 4 VO (V) (200mV/div) 7 6 IO (A) (5A/div) Io=0A OUTPUT CURRENT, OUTPUT VOLTAGE INPUT CURRENT, IIN (A) Io=5A 8 OUTPUT CURRENT, OUTPUT VOLTAGE Io=10A 9 TIME, t (20μs/div) Figure 12. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3 Vdc, Cext = 2x150 μF Polymer Capacitors). 7 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Characteristic Curves (continued) VNN (V) (2V/div) VOV) (1V/div) OUTPUT VOLTAGE INPUT VOLTAGE Figure 15. Typical Start-Up Using Remote On/Off with external capacitors (Vin = 5.5Vdc, Vo = 3.3Vdc, Io = 10A, Co = 1050μF). LINEAGE POWER VOn/off (V) (2V/div) On/Off VOLTAGE On/Off VOLTAGE TIME, t (2 ms/div) TIME, t (2 ms/div) Figure 17. Typical Start-Up with Prebias (Vin = 3.3Vdc, Vo = 1.8Vdc, Io = 1A, Vbias =1.0Vdc). OUTPUT CURRENT, VOV) (1V/div) OUTPUT VOLTAGE VOn/off (V) (2V/div) Figure 14. Typical Start-Up Using Remote On/Off (Vin = 5.5 Vdc, Vo = 3.3Vdc, Io = 10A). On/Off VOLTAGE TIME, t (2 ms/div) TIME, t (2 ms/div) Figure 16. Typical Start-Up with application of Vin (Vin = 5.5Vdc, Vo = 3.3Vdc, Io = 10A). VOV) (1V/div) VOV) (1V/div) OUTPUT VOLTAGE VOn/off (V) (2V/div) Figure 13. Transient Response to Dynamic Load Change from 100% of 50% full load (Vo = 5.0 Vdc, Cext = 2x150 μF Polymer Capacitors). OUTPUT VOLTAGE TIME, t (20μs/div) IO (A) (10A/div) VO (V) (50mV/div) IO (A) (5A/div) OUTPUT CURRENT, OUTPUT VOLTAGE The following figures provide typical characteristics for the Austin LynxTM II SMT modules at 25ºC. TIME, t (10ms/div) Figure 18. Output short circuit Current (Vin = 5.0Vdc, Vo = 0.75Vdc). 8 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Characteristic Curves (continued) 12 12 10 10 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) The following figures provide thermal derating curves for the Austin LynxTM II SMT modules. 8 6 4 NC 2 100 LFM 0 20 30 40 50 60 70 80 8 6 4 NC 2 100 LFM 0 90 20 O 10 OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) 10 8 6 4 NC 2 100 LFM 0 50 60 70 80 60 70 80 90 AMBIENT TEMPERATURE, TA C 12 40 50 Figure 22. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 5.0dc, Vo=3.3 Vdc). 12 30 40 O AMBIENT TEMPERATURE, TA C Figure 19. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 5.0, Vo=0.75Vdc). 20 30 90 O 8 6 4 NC 2 0 20 30 40 50 60 70 80 90 O AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Figure 20. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 5.0Vdc, Vo=1.8 Vdc). Figure 23. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 3.3Vdc, Vo=2.5 Vdc). OUTPUT CURRENT, Io (A) 12 10 8 6 4 NC 2 100 LFM 0 20 30 40 50 60 70 80 90 O AMBIENT TEMPERATURE, TA C Figure 21. Derating Output Current versus Local Ambient Temperature and Airflow (Vin = 5.0Vdc, Vo=2.5 Vdc). LINEAGE POWER 9 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Test Configurations Design Considerations CURRENT PROBE TO OSCILLOSCOPE VIN(+) BATTERY CIN CS 1000μF Electrolytic 2x100μF Tantalum E.S.R.<0.1Ω TM The Austin Lynx II SMT module should be connected to a low ac-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. LTEST 1μH Input Filtering @ 20°C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1μH. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 24. Input Reflected Ripple Current Test Setup. COPPER STRIP To minimize input voltage ripple, low-ESR polymer and ceramic capacitors are recommended at the input of the module. Figure 27 shows input ripple voltage (mVp-p) for various outputs with 1x150 µF polymer capacitors (Panasonic p/n: EEFUE0J151R, Sanyo p/n: 6TPE150M) in parallel with 1 x 47 µF ceramic capacitor (Panasonic p/n: ECJ-5YB0J476M, Taiyo- Yuden p/n: CEJMK432BJ476MMT) at full load. Figure 28 shows the input ripple with 3x150 µF polymer capacitors in parallel with 2 x 47 µF ceramic capacitor at full load. RESISTIVE LOAD 1uF . 10uF SCOPE COM GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 25. Output Ripple and Noise Test Setup. Input Ripple Voltage (mVp-p) 160 VO (+) 3.3Vin 140 5Vin 120 100 80 60 40 20 0 0 Rdistribution Rcontact Rcontact VIN(+) VO RLOAD VO VIN 0.5 1 1.5 2 2.5 3 3.5 Rdistribution Output Voltage (Vdc) Figure 27. Input ripple voltage for various outputs with 1x22 µF ceramic capacitor at the input (fullload). 160 Rcontact Rcontact COM COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 26. Output Voltage and Efficiency Test Setup. VO. IO Efficiency η = VIN. IIN x 100 % 3.3Vin Rdistribution Input Ripple Voltage (mVp-p) Rdistribution 140 5Vin 120 100 80 60 40 20 0 0 0.5 1 1.5 2 2.5 3 3.5 Output Voltage (Vdc) Figure 28. Input ripple voltage for various outputs with 1x47 µF ceramic capacitor at the input (full load). LINEAGE POWER 10 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Design Considerations (continued) Safety Considerations Output Filtering For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE 0850:2001-12 (EN60950-1) Licensed. TM The Austin Lynx II SMT module is designed for low output ripple voltage and will meet the maximum output ripple specification with 1 µF ceramic and 10 µF tantalum capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. LINEAGE POWER For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a fastacting fuse with a maximum rating of 15A in the positive input lead. 11 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Feature Description VIN+ Remote On/Off TM The Austin Lynx II SMT power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available in the Austin LynxTM II series modules. Positive Logic On/Off signal, device code suffix “4”, turns the module ON during a logic High on the On/Off pin and turns the module OFF during a logic Low. Negative logic On/Off signal, no device code suffix, turns the module OFF during logic High on the On/Off pin and turns the module ON during logic Low. For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 29. The On/Off pin is an open collector/drain logic input signal (Von/Off) that is referenced to ground. During a logic-high (On/Off pin is pulled high internal to the module) when the transistor Q1 is in the Off state, the power module is ON. Maximum allowable leakage current of the transistor when Von/off = VIN,max is 10µA. Applying a logic-low when the transistor Q1 is turned-On, the power module is OFF. During this state VOn/Off must be less than 0.3V. When not using positive logic On/off pin, leave the pin unconnected or tie to VIN. MODULE VIN+ R2 ON/OFF + I ON/OFF VON/OFF PWM Enable Q1 I ON/OFF ON/OFF + VON/OFF PWM Enable R1 Q2 Q1 CSS R2 GND _ Figure 30. Circuit configuration for using negative logic On/OFF. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The typical average output current during hiccup is 3.0A. Input Undervoltage Lockout Q2 R1 R3 Q3 CSS R4 GND MODULE Rpull-up _ Figure 29. Circuit configuration for using positive logic On/OFF. For negative logic On/Off devices, the circuit configuration is shown is Figure 30. The On/Off pin is pulled high with an external pull-up resistor (typical Rpullup = 5k, +/- 5%). When transistor Q1 is in the Off state, logic High is applied to the On/Off pin and the power module is Off. The minimum On/off voltage for logic High on the On/Off pin is 1.5Vdc. To turn the module ON, logic Low is applied to the On/Off pin by turning ON Q1. When not using the negative logic On/Off, leave the pin unconnected or tie to GND. At input voltages below the input undervoltage lockout limit, module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Overtemperature Protection To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will shutdown if the thermal reference point Tref, o exceeds 125 C (typical), but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restarts after it cools down. Output Voltage Programming TM The output voltage of the Austin Lynx II SMT can be programmed to any voltage from 0.75 Vdc to 3.63 Vdc by connecting a single resistor (shown as Rtrim in Figure 31) between the TRIM and GND pins of the module. Without an external resistor between the TRIM pin and the ground, the output voltage of the module is 0.7525 Vdc. To calculate the value of the resistor Rtrim for a particular output voltage Vo, use the following equation: ⎡ 21070 ⎤ Rtrim = ⎢ − 5110⎥ Ω ⎣Vo − 0.7525 ⎦ LINEAGE POWER 12 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Feature Descriptions (continued) Output Voltage Programming (continued) For example, to program the output voltage of the TM Austin Lynx II module to 1.8 Vdc, Rtrim is calculated is follows: ⎤ ⎡ 21070 Rtrim = ⎢ − 5110⎥ Ω ⎦ ⎣1.8 − 0.7525 Voltage Margining Rtrim = 15.004 kΩ V IN(+) V O(+) ON/OFF TRIM The amount of power delivered by the module is defined as the voltage at the output terminals multiplied by the output current. When using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module remains at or below the maximum rated power (Pmax = Vo,set x Io,max). LOAD R trim Output voltage margining can be implemented in the Austin LynxTM II modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the Output pin for margining-down. Figure 32 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local Lineage Power technical representative for additional details. GND Vo Figure 31. Circuit configuration to program output voltage using an external resistor. Table 1 provides Rtrim values required for some common output voltages. Rmargin-down Austin Lynx or Lynx II Series Q2 Table 1 VO, (V) Rtrim (KΩ) 0.7525 Open 1.2 41.973 1.5 23.077 1.8 15.004 2.5 6.947 3.3 3.160 By a using 1% tolerance trim resistor, set point tolerance of ±2% is achieved as specified in the electrical specification. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, helps determine the required external trim resistor needed for a specific output voltage.. LINEAGE POWER Trim Rmargin-up Rtrim Q1 GND Figure 32. Circuit Configuration for margining Output voltage. 13 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Feature Descriptions (continued) Remote Sense Voltage Sequencing The Austin Lynx II SMT power modules have a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage at the Remote Sense pin (See Figure 33). The voltage between the Sense pin and Vo pin must not exceed 0.5V. TM The Austin Lynx II series of modules include a sequencing feature, EZ-SEQUENCETM that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either tie the SEQ pin to VIN or leave it unconnected. When an analog voltage is applied to the SEQ pin, the output voltage tracks this voltage until the output reaches the set-point voltage. The SEQ voltage must be set higher than the set-point voltage of the module. The output voltage follows the voltage on the SEQ pin on a one-to-one volt basis. By connecting multiple modules together, customers can get multiple modules to track their output voltages to the voltage applied on the SEQ pin. TM The amount of power delivered by the module is defined as the output voltage multiplied by the output current (Vo x Io). When using Remote Sense, the output voltage of the module can increase, which if the same output is maintained, increases the power output by the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. When the Remote Sense feature is not being used, connect the Remote Sense pin to output pin of the module. R d istrib u tio n R co n ta c t R c o nta ct V IN (+ ) For proper voltage sequencing, first, input voltage is applied to the module. The On/Off pin of the module is left unconnected (or tied to GND for negative logic modules or tied to VIN for positive logic modules) so that the module is ON by default. After applying input voltage to the module, a minimum of 10msec delay is required before applying voltage on the SEQ pin. During this time, potential of 50mV (± 10 mV) is maintained on the SEQ pin. After 10msec delay, an analog voltage is applied to the SEQ pin and the output voltage of the module will track this voltage on a one-toone volt bases until output reaches the set-point voltage. To initiate simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. Output voltage of the modules tracks the voltages below their set-point voltages on a one-to-one basis. A valid input voltage must be maintained until the tracking and output voltages reach ground potential. R d istrib utio n VO S e n se R LO AD R d istrib u tio n R co n ta c t R c o nta ct COM R d istrib utio n COM Figure 33. Remote sense circuit configuration. When using the EZ-SEQUENCETM feature to control start-up of the module, pre-bias immunity feature during start-up is disabled. The pre-bias immunity feature of the module relies on the module being in the diodemode during start-up. When using the EZSEQUENCETM feature, modules goes through an internal set-up time of 10msec, and will be in synchronous rectification mode when voltage at the SEQ pin is applied. This will result in sinking current in the module if pre-bias voltage is present at the output of the module. When pre-bias immunity during start-up is required, the EZ-SEQUENCETM feature must be disabled. For additional guidelines on using EZTM TM SEQUENCE feature of Austin Lynx II, contact the Lineage Power technical representative for preliminary application note on output voltage sequencing using Austin Lynx II series. LINEAGE POWER 14 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 35. Note that the airflow is parallel to the long axis of the module as shown in figure 34. The derating data applies to airflow in either direction of the module’s long axis. 25.4_ (1.0) Wind Tunnel PWBs Power Module 76.2_ (3.0) x Top View 8.3_ (0.325) Probe Location for measuring airflow and ambient temperature Air flow Figure 35. Thermal Test Set-up. Tref Bottom View Heat Transfer via Convection Increased airflow over the module enhances the heat transfer via convection. Thermal derating curves showing the maximum output current that can be delivered at different local ambient temperature (TA) for airflow conditions ranging from natural convection and up to 2m/s (400 ft./min) are shown in the Characteristics Curves section. Air Flow Figure 34. Tref Temperature measurement location. The thermal reference point, Tref used in the specifications is shown in Figure 34. For reliable operation this temperature should not exceed 115 oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note “Thermal Characterization Process For Open-Frame BoardMounted Power Modules” for a detailed discussion of thermal aspects including maximum device temperatures. LINEAGE POWER 15 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) Top View Side View Bottom View LINEAGE POWER 16 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) LINEAGE POWER PIN FUNCTION 1 On/Off 2 VIN 3 SEQ 4 GND 5 VOUT 6 Trim 7 Sense 17 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Packaging Details The Austin LynxTM II SMT version is supplied in tape & reel as standard. Modules are shipped in quantities of 250 modules per reel. Pick Point All Dimensions are in millimeters and (in inches). Reel Dimensions Outside diameter: Inside diameter: Tape Width: LINEAGE POWER 330.2 mm (13.00) 177.8 mm (7.00”) 44.0 mm (1.73”) 18 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Surface Mount Information Pick and Place 300 P eak Temp 235oC TM 250 REFLOW TEMP (°C) The Austin Lynx II SMT modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place operations. The label meets all the requirements for surface mount processing, as well as safety standards, and is able to withstand reflow temperatures of up to 300oC. The label also carries product information such as product code, serial number and location of manufacture. TM The Austin Lynx II SMT power modules are lead free modules and can be soldered either in a lead-free solder process or in a conventional Tin/Lead (Sn/Pb) process. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. 150 So ak zo ne 30-240s 100 Tlim above 205oC P reheat zo ne max 4oCs -1 0 REFLOW TIME (S) Figure 36. Reflow Profile for Tin/Lead (Sn/Pb) process. 240 235 MAX TEMP SOLDER (°C) Tin Lead Soldering 200 50 Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Even so, these modules have a relatively large mass when compared to conventional SMT components. Variables such as nozzle size, tip style, vacuum pressure and pick & placement speed should be considered to optimize this process. The minimum recommended nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 8 mm max. Co o ling zo ne 1-4oCs -1 Heat zo ne max 4oCs -1 230 225 220 215 210 205 200 0 10 20 30 40 50 60 o Figure 37. Time Limit Curve Above 205 C Reflow for Tin Lead (Sn/Pb) process. In a conventional Tin/Lead (Sn/Pb) solder process peak reflow temperatures are limited to less than 235oC. Typically, the eutectic solder melts at 183oC, wets the land, and subsequently wicks the device connection. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. There are several types of SMT reflow technologies currently used in the industry. These surface mount power modules can be reliably soldered using natural forced convection, IR (radiant infrared), or a combination of convection/IR. For reliable soldering the solder reflow profile should be established by accurately measuring the modules CP connector temperatures. LINEAGE POWER 19 Data Sheet August 28, 2009 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Surface Mount Information (continued) 300 Lead Free Soldering 250 Peak Temp 260°C Reflow Temp (°C) The –Z version Austin Lynx II SMT modules are leadfree (Pb-free) and RoHS compliant and are both forward and backward compatible in a Pb-free and a SnPb soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Per J-STD-020 Rev. C 200 150 * Min. Time Above 235°C 15 Seconds Heating Zone 1°C/Second Cooling Zone *Time Above 217°C 60 Seconds 100 50 0 Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure. 38. Reflow Time (Seconds) Figure 38. Recommended linear reflow profile using Sn/Ag/Cu solder. MSL Rating The Austin Lynx II SMT modules have a MSL rating of 1 Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of <= 30°C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40° C, < 90% relative humidity. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). LINEAGE POWER 20 Austin LynxTM II SMT Non-isolated Power Modules: 2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 10A output current Data Sheet August 28, 2009 Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 2. Device Codes Device Code Input Voltage Range Output Voltage Output Current Efficiency 3.3V@ 10A On/Off Logic Connector Type Comcodes ATH010A0X3-SR 2.4 – 5.5Vdc 0.75 – 3.63Vdc 10 A 95% Negative SMT 108987520 ATH010A0X3-SRZ 2.4 – 5.5Vdc 0.75 – 3.63Vdc 10 A 95% Negative SMT CC109104543 ATH010A0X43-SR 2.4 – 5.5Vdc 0.75 – 3.63Vdc 10 A 95% Positive SMT 108988333 ATH010A0X43-SRZ 2.4 – 5.5Vdc 0.75 – 3.63Vdc 10 A 95% Positive SMT 108996823 -Z refers to RoHS compliant codes Asia-Pacific Headquarters Tel: +65 6416 4283 World Wide Headquarters Lineage Power Corporation 3000 Skyline Drive, Mesquite, TX 75149, USA +1-800-526-7819 (Outside U.S.A.: +1-972-284-2626) www.lineagepower.com e-mail: [email protected] Europe, Middle-East and Africa Headquarters Tel: +49 89 6089 286 India Headquarters Tel: +91 80 28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. © 2008 Lineage Power Corporation, (Mesquite, Texas) All International Rights Reserved. LINEAGE POWER 21 Document No: DS03-105 ver. 1.03 PDF name: lynx_II_smt_ds.pdf