Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals HAND CRIMP TOOL Specification Sheet Order No. 63819-4400 TYPE 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position Right and Left handed applications This tool is IPC/WHMA A-620 Class 2 compliant This tool is RoHS compliant, however RoHS compliant is not required SCOPE Products: 1.25mm (.049") Pitch Wire-to-Board Crimp Terminal, 26-28 AWG. 1.25mm (.049") Pitch CLIK-Mate™ Wire-to-Board Crimp Terminal, 26-28 AWG. Terminal Series No. 501930 502381 Terminal Order No. Wire Size Insulation Diameter IPC/WHMA-A620 Terminal mm In. mm In. Strip Length Loose Piece Reel AWG mm² mm In. 501930-0200 501930-0100 26-28 .136-.079 0.80-1.00 .032-.039 0.80-1.00 .031-.039 1.50-1.70 .059-.067 501930-1200 501930-1100 502381-0000 26-28 .136-.079 0.80-1.00 .032-.039 0.80-1.00 .031-.039 1.50-1.70 .059-.067 502381-0010 Customer to cut off terminal from reel: 0.15mm (.006”) maximum Cut-off Tab. To achieve optimum IPC-A620 Class 2 insulation crimps, use this insulation OD range. Overall insulation OD specification for terminal. DEFINITION OF TERMS BEND UP BRUSH BELL MOUTH ROLLING CONDUCTOR CRIMP INSULATION CRIMP TWISTING STRIP LENGTH BEND DOWN CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 1 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals CONDITIONS: After crimping, the conductor profile should measure the following. Terminal Series No. 501930 502381 Terminal Series No. 501930 502381 Wire Size AWG 26 28 26 28 mm2 0.13 0.08 0.13 0.08 Wire Size AWG 26 28 26 28 mm2 0.13 0.08 0.13 0.08 Conductor Profile Crimp Height Crimp Width (Ref) 501930 502381 mm In. mm In. 26 28 26 28 0.56-0.61 .022-.024 0.80 .031 X 0.80 .031 X 0.53-0.58 .021-.023 0.56-0.61 .022-.024 0.80 .031 X 0.80 .031 X 0.53-0.58 .021-.023 Insulation (Ref) Pull Force Minimum Crimp Height Crimp Width mm In. mm In. N Lb. 1.19-1.25 .047-.049 0.80 .031 9.8 2.20 9.8 2.20 1.15-1.21 .045-.048 0.80 .031 1.18-1.28 .046-.050 0.80 .031 9.8 2.20 1.15-1.25 .045-.049 0.80 .031 9.8 2.20 OPERATION CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage can occur to the tool or die. Open the tool by squeezing the handles together. At the end of the closing stroke, the ratchet mechanism will release the handles and the hand tool will spring open. See Figure 1. HANDLE WILL SPRING OPEN Crimping Terminals 1. Select the desired terminal listed in the preceding charts. 2. Make sure the center of the locator is in the down position. With the locator attached, push the locator button on the back of the hand tool to bring the locator forward through the tooling. See Figure 2. 3. While holding the locator button in, load the terminal into the proper nest opening in the locator based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. LOCATOR IN DOWN POSTION SQUEEZE HANDLES TOGETHER Figure 1 Figure 2 Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 PUSH ON THE LOCATOR BUTTON UNCONTROLLED COPY Page 2 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals LOCATOR PUSHED THRU TOOLING RELEASE LOCATOR BUTTON LOCATOR LOCATOR BUTTON PUSHED IN TERMINAL Figure 3 TERMINAL 4. Release the locator button, allowing the locator to return to the crimping position. 5. Close the tool handle until the first ratchet position engages. See Figure 4. 6. Insert the properly stripped wire through the terminal and against the wire stop. See Figure 5. 7. Crimp the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed. Release the handles to open the jaws. TOOLING PARTIALLY CLOSED PARTIALLY CLOSE HANDLE OPEN POSITION FIRST RATCHET POSITION Figure 4 WIRE AGAINST THE WIRE STOP TERMINAL WIRE STOP IS PART OF THE LOCATOR PRE-STRIPPED WIRE Figure 5 WIRE TERMINAL Note: The tamper proof ratchet action will not release the tool until it has been fully closed. 8. Remove the crimped terminal from the terminal locator by pulling on the wire. 9. Visually inspect the crimped terminal for proper crimp location. Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 3 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals WIRE 10. On some large O.D. wires, it may not be possible to insert the wire with the tool partially closed. Those wires should be inserted with the hand tool in the open position. Insert the wire above the terminal in the punch and against the wire stop then close the tool. See Figure 6. WIRE STOP Note: Figure 6 A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands, insulation diameters, and durometers available, actual crimp height measurements may very slightly. An occasional, destructive, pull force test should be performed to check hand tool crimp. Pull Force value Must exceed the Minimum pull force specifications listed. Locator Replacement TERMINAL LOCATOR SQUEEZE HERE SQUEEZE HERE Figure 7A See the parts list on the last page of this document for the proper locator order number. Follow the steps below to replace the locator. 1. Open the crimp hand tool. 2. Squeeze gently on the lower area shown in Figure 7A with your thumb and index finger. The lower tabs of the locator should disengage from the hand tool. 3. Lift and pull away from the hand tool. The top locator hooks should slip out of the top slots easily. See Figure 7A. 4. To reinstall the new locator, make sure the hand tool is in the open position. 5. Press the red insert down as far as it will go as shown in Figure 7B. 6. Holding onto the lower part of the locator with your thumb and index finger, insert the locators top hooks (2) into the hand tool top slots. 7. Rotate the locator down and press the lower tabs into the two bottom slots of the hand tool. To secure the locator into place, the lower tabs must snap into place on the hand tool frame. MAKE SURE CENTER OF LOCATORR IS IN THE DOWN POSITION TOP SLOTS OF HANDTOOL TOP HOOKS Figure 7B LOWER TABS AWS OPEN PULL OPEN TOOLING TOOLING M3 BHCS Figure 8 PUSH ON HANDLE Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 4 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals Right or Left Hand Operation MATCH UP MARKS This hand tool has an added feature that can be converted from a right handed application to a left handed application. It is necessary to reverse the tooling if using the left handed application along with the locator. Follow the steps below: Figure 9 BACK FRONT 1. The locator must be removed before reversing the tooling. 2. Remove the M3 BHCS which is holding the upper tooling. 3. Flip the upper tooling to the opposite side and replace the M3 BHCS. Make sure the small markings on the front and back of the hand tool frame match up and are on the outside of the hand tool frame. See Figure 8 and 9. 4. Do the same thing with the lower tooling and tighten the M3 screws. Be sure the small markings line up. 5. Reinstall the locator by following the Instructions in the locator LUBRICATION POINTS replacement section. (BOTH SIDES) LIGHT OIL (EVERY 3 MONTHS OR 5,000 CRIMPS) Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: Figure 10 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. RATCHET RELEASE LEVER 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil Figure 11 transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by pressing up on the ratchet release lever in the movable handle. See Figure 11. Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 5 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals How to Adjust Tool Preload (See Figure 12) This hand tool is factory preset to 25-45 LBS. preload. It may be necessary over the life of the tool to adjust tool handle preload force. Listed below are the steps required to adjust the crimping force of the hand tool to obtain proper crimp conditions: RATCHET RELEASE LEVER SQUEEZE THE LINK IN THE HANDLE HOLD THE HAND TOOL IN POSITION 1. Hold the hand tool in the palm of your hand as shown in Figure 10. Using Figure 12 the index finger squeeze the link SETTING towards the top of the hand tool WHEEL frame. This will release the preload adjustment wheel. 2. Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher. To decrease handle force rotate the setting wheel clockwise (CW). 3. Release the link to lock the setting wheel in place. 4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Certification Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify hand tools. % This tool is qualified to pull force only. See the Molex web site for the Quality Crimp Handbook for more information on pull testing. % If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). % When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 6 of 7 Hand Crimp Tool For 1.25mm (.049") Pitch Crimp Terminals PARTS LIST Item Number REF 1 2 3 Order Number 63819-4400 63819-4475 63810-0104 63810-0105 Description Hand Crimp Tool Locator Assembly Spring, Return Spring, Ratchet Quantity Figure 13 1 1 1 2 1 RATCHET RELEASE LEVER Figure 13 Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX [email protected] Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 [email protected] 3 Far East South Headquarters Jurong, Singapore 65-6-268-6868 [email protected] European Headquarters Munich, Germany 49-89-413092-0 [email protected] Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-638194400 Revision: A Release Date: 10-31-08 Revision Date: 10-31-08 UNCONTROLLED COPY Page 7 of 7