IRF AUIRFS3004-7TRR Advanced process technology ultra low on-resistance Datasheet

PD - 97704A
AUTOMOTIVE GRADE
AUIRFS3004-7P
HEXFET® Power MOSFET
Features
l
l
l
l
l
l
●
Advanced Process Technology
Ultra Low On-Resistance
175°C Operating Temperature
Fast Switching
Repetitive Avalanche Allowed up to Tjmax
Lead-Free, RoHS Compliant
Automotive Qualified *
D
G
S
Description
VDSS
RDS(on) typ.
max.
ID (Silicon Limited)
40V
0.90m
1.25m
400A
ID (Package Limited)
240A
Specifically designed for Automotive applications, this
HEXFET® Power MOSFET utilizes the latest processing
techniques to achieve extremely low on-resistance per
silicon area. Additional features of this design are a 175°C
junction operating temperature, fast switching speed and
improved repetitive avalanche rating. These features
combine to make this design an extremely efficient and
reliable device for use in Automotive applications such as
Electric Power Steering, Battery Switch, SMPS and other
heavy loads.
c
D
S
S
G
S
S
S
D2Pak 7 Pin
G
D
S
Gate
Drain
Source
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only; and
functional operation of the device at these or any other condition beyond those indicated in the specifications is not implied. Exposure to absolutemaximum-rated conditions for extended periods may affect device reliability. The thermal resistance and power dissipation ratings are measured under
board mounted and still air conditions. Ambient temperature (TA) is 25°C, unless otherwise specified.
Symbol
ID @ TC = 25°C
ID @ TC = 100°C
ID @ TC = 25°C
IDM
PD @TC = 25°C
VGS
EAS
IAR
EAR
Parameter
Max.
Continuous Drain Current, VGS @ 10V (Silicon Limited)
Continuous Drain Current, VGS @ 10V (Silicon Limited)
Continuous Drain Current, VGS @ 10V (Wire Bond Limited)
d
Pulsed Drain Current
Maximum Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy (Thermally limited)
Avalanche Current
Repetitive Avalanche Energy
d
f
e
d
2.0
-55 to + 175
Peak Diode Recovery
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds (1.6mm from case)
dv/dt
TJ
TSTG
Units
c
c
400
280
240
1610
380
2.5
± 20
290
See Fig. 14, 15, 22a, 22b
A
W
W/°C
V
mJ
A
mJ
V/ns
°C
300
Thermal Resistance
Symbol
RJC
RJA
Parameter
kl
Junction-to-Case
Junction-to-Ambient (PCB Mount)
j
Typ.
Max.
Units
–––
–––
0.40
40
°C/W
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
www.irf.com
1
11/29/11
AUIRFS3004-7P
Static Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Symbol
Parameter
V(BR)DSS
V(BR)DSS/TJ
RDS(on)
VGS(th)
gfs
RG
IDSS
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
Static Drain-to-Source On-Resistance
Gate Threshold Voltage
Forward Transconductance
Internal Gate Resistance
Drain-to-Source Leakage Current
IGSS
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Min. Typ. Max. Units
40
––– –––
––– 0.038 –––
––– 0.90 1.25
2.0
–––
4.0
1300 ––– –––
–––
2.0
–––
––– –––
20
––– ––– 250
––– ––– 100
––– ––– -100
Conditions
V VGS = 0V, ID = 250μA
V/°C Reference to 25°C, ID = 5mA
m VGS = 10V, ID = 195A
V VDS = VGS, ID = 250μA
S VDS = 10V, ID = 195A

μA VDS = 40V, VGS = 0V
VDS = 40V, VGS = 0V, TJ = 125°C
nA VGS = 20V
VGS = -20V
d
g
Dynamic Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Symbol
Qg
Qgs
Qgd
Qsync
td(on)
tr
td(off)
tf
Ciss
Coss
Crss
Coss eff. (ER)
Coss eff. (TR)
Parameter
Min. Typ. Max. Units
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Total Gate Charge Sync. (Qg - Qgd)
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Effective Output Capacitance (Energy Related)
Effective Output Capacitance (Time Related)
h
i
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
160
42
65
95
23
240
91
160
9130
2020
990
2590
2650
240
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
–––
nC
Conditions
ID = 180A
VDS =20V
VGS = 10V
ID = 180A, VDS =0V, VGS = 10V
VDD = 26V
ID = 240A
RG = 2.7
VGS = 10V
VGS = 0V
VDS = 25V
ƒ = 1.0 MHz, See Fig. 5
VGS = 0V, VDS = 0V to 32V , See Fig. 11
VGS = 0V, VDS = 0V to 32V
g
ns
pF
g
i
h
Diode Characteristics
Symbol
IS
Parameter
Continuous Source Current
VSD
trr
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Qrr
Reverse Recovery Charge
IRRM
ton
Reverse Recovery Current
Forward Turn-On Time
ISM
d
Notes:
 Calculated continuous current based on maximum allowable junction
temperature. Bond wire current limit is 240A. Note that current
limitations arising from heating of the device leads may occur with
some lead mounting arrangements. (Refer to AN-1140)
‚ Repetitive rating; pulse width limited by max. junction
temperature.
ƒ Limited by TJmax, starting TJ = 25°C, L = 0.01mH
RG = 25, IAS = 240A, VGS =10V. Part not recommended for use
above this value .
2
Min. Typ. Max. Units
–––
–––
–––
Conditions
c
A
MOSFET symbol
1610
A
showing the
integral reverse
––– 400
D
G
p-n junction diode.
TJ = 25°C, IS = 195A, VGS = 0V
TJ = 25°C
VR = 34V,
TJ = 125°C
IF = 240A
di/dt = 100A/μs
TJ = 25°C
g
S
––– –––
1.3
V
–––
49
–––
ns
–––
51
–––
–––
37
–––
nC
TJ = 125°C
–––
41
–––
–––
3.2
–––
A TJ = 25°C
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
g
„ ISD  240A, di/dt  740A/μs, VDD V(BR)DSS, TJ  175°C.
Pulse width  400μs; duty cycle  2%.
† Coss eff. (TR) is a fixed capacitance that gives the same charging time
as Coss while VDS is rising from 0 to 80% VDSS .
‡ Coss eff. (ER) is a fixed capacitance that gives the same energy as
Coss while VDS is rising from 0 to 80% VDSS.
ˆ When mounted on 1" square PCB (FR-4 or G-10 Material). For recom
mended footprint and soldering techniques refer to application note #AN-994.
‰ R is measured at TJ approximately 90°C.
Š RJC value shown is at time zero.
www.irf.com
AUIRFS3004-7P
Qualification Information
†
Automotive
(per AEC-Q101)
Qualification Level
Comments: This part number(s) passed Automotive qualification. IR’s
Industrial and Consumer qualification level is granted by extension of the
higher Automotive level.
D2 PAK - 7 Pin
Machine Model
††
MSL1
Class M4 (+/- 800V)†††
AEC-Q101-002
ESD
Human Body Model
Class H3A (+/- 6000V)†††
AEC-Q101-001
Charged Device Model
Class C5 (+/- 2000V)†††
AEC-Q101-005
RoHS Compliant
Yes
† Qualification standards can be found at International Rectifier’s web site: http://www.irf.com/
†† Exceptions (if any) to AEC-Q101 requirements are noted in the qualification report.
††† Highest passing voltage.
www.irf.com
3
AUIRFS3004-7P
1000
1000
100
BOTTOM
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
BOTTOM
100
10
1
4.5V
60μs PULSE WIDTH
0.1
1
10
100
0.1
1000
1
10
100
1000
V DS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
Fig 2. Typical Output Characteristics
1000
2.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
ID, Drain-to-Source Current (A)
Tj = 175°C
10
V DS, Drain-to-Source Voltage (V)
100
T J = 175°C
T J = 25°C
10
1
VDS = 25V
60μs PULSE WIDTH
0.1
ID = 195A
VGS = 10V
1.5
1.0
0.5
3
4
5
6
7
8
-60 -40 -20 0 20 40 60 80 100120140160180
VGS, Gate-to-Source Voltage (V)
T J , Junction Temperature (°C)
Fig 3. Typical Transfer Characteristics
Fig 4. Normalized On-Resistance vs. Temperature
100000
14.0
VGS = 0V,
f = 1 MHZ
C iss = C gs + C gd, C ds SHORTED
C rss = C gd
VGS, Gate-to-Source Voltage (V)
ID= 180A
C oss = C ds + C gd
C, Capacitance (pF)
60μs PULSE WIDTH
4.5V
Tj = 25°C
0.1
Ciss
10000
Coss
Crss
1000
12.0
VDS= 32V
VDS= 20V
10.0
8.0
6.0
4.0
2.0
0.0
100
1
10
100
VDS, Drain-to-Source Voltage (V)
Fig 5. Typical Capacitance vs. Drain-to-Source Voltage
4
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
0
50
100
150
200
250
QG, Total Gate Charge (nC)
Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage
www.irf.com
AUIRFS3004-7P
10000
T J = 175°C
100
ID, Drain-to-Source Current (A)
ISD, Reverse Drain Current (A)
1000
T J = 25°C
10
1
OPERATION IN THIS AREA
LIMITED BY R DS(on)
1000
100μsec
100
1msec
10msec
10
Tc = 25°C
Tj = 175°C
Single Pulse
VGS = 0V
0.1
1
0.0
0.5
1.0
1.5
2.0
0
VSD, Source-to-Drain Voltage (V)
300
240
180
120
60
0
50
75
100
125
150
175
V(BR)DSS , Drain-to-Source Breakdown Voltage (V)
ID, Drain Current (A)
Limited By Package
25
10
100
Fig 8. Maximum Safe Operating Area
420
360
1
VDS, Drain-to-Source Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
50
Id = 5mA
48
46
44
42
40
-60 -40 -20 0 20 40 60 80 100120140160180
T J , Temperature ( °C )
T C , Case Temperature (°C)
Fig 9. Maximum Drain Current vs.
Case Temperature
3.5
Fig 10. Drain-to-Source Breakdown Voltage
EAS , Single Pulse Avalanche Energy (mJ)
1200
3.0
ID
44A
80A
BOTTOM 240A
TOP
1000
2.5
Energy (μJ)
DC
2.0
1.5
1.0
0.5
0.0
800
600
400
200
0
-5
0
5
10 15 20 25 30 35 40 45
VDS, Drain-to-Source Voltage (V)
Fig 11. Typical COSS Stored Energy
www.irf.com
25
50
75
100
125
150
175
Starting T J , Junction Temperature (°C)
Fig 12. Maximum Avalanche Energy vs. DrainCurrent
5
AUIRFS3004-7P
Thermal Response ( Z thJC ) °C/W
1
D = 0.50
0.1
0.20
0.10
J
0.05
0.02
0.01
0.01
R1
R1
J
1
R2
R2
R3
R3
C

2
1
2
3
3
4
4
Ci= iRi
Ci iRi
1E-005
0.00757
0.000006
0.06508
0.000064
0.18313
0.001511
0.14378
0.009800
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
SINGLE PULSE
( THERMAL RESPONSE )
0.001
1E-006
Ri (°C/W) i (sec)
R4
R4
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 13. Maximum Effective Transient Thermal Impedance, Junction-to-Case
1000
Avalanche Current (A)
Duty Cycle = Single Pulse
Allowed avalanche Current vs avalanche
pulsewidth, tav, assuming Tj = 150°C and
Tstart =25°C (Single Pulse)
0.01
100
0.05
0.10
10
Allowed avalanche Current vs avalanche
pulsewidth, tav, assuming  j = 25°C and
Tstart = 150°C.
1
1.0E-06
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
tav (sec)
Fig 14. Typical Avalanche Current vs.Pulsewidth
320
280
EAR , Avalanche Energy (mJ)
Notes on Repetitive Avalanche Curves , Figures 14, 15:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a temperature far in
excess of Tjmax. This is validated for every part type.
2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded.
3. Equation below based on circuit and waveforms shown in Figures 16a, 16b.
4. PD (ave) = Average power dissipation per single avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase
during avalanche).
6. Iav = Allowable avalanche current.
7. T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as
25°C in Figure 14, 15).
tav = Average time in avalanche.
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav) = Transient thermal resistance, see Figures 13)
TOP
Single Pulse
BOTTOM 1.0% Duty Cycle
ID = 240A
240
200
160
120
80
40
0
25
50
75
100
125
150
175
Starting T J , Junction Temperature (°C)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
Fig 15. Maximum Avalanche Energy vs. Temperature
6
www.irf.com
4.5
10
4.0
9
8
3.5
3.0
2.5
ID = 250μA
ID = 1.0mA
ID = 1.0A
2.0
7
IRRM (A)
VGS(th), Gate threshold Voltage (V)
AUIRFS3004-7P
IF = 96A
V R = 34V
TJ = 25°C
TJ = 125°C
6
5
4
1.5
3
2
1.0
-75 -50 -25 0
100
25 50 75 100 125 150 175 200
200
T J , Temperature ( °C )
400
500
Fig. 17 - Typical Recovery Current vs. dif/dt
Fig 16. Threshold Voltage vs. Temperature
140
12
IF = 144A
V R = 34V
11
10
TJ = 25°C
TJ = 125°C
9
8
120
IF = 96A
V R = 34V
100
TJ = 25°C
TJ = 125°C
QRR (nC)
IRRM (A)
300
diF /dt (A/μs)
7
6
80
60
5
4
40
3
20
2
100
200
300
400
100
500
200
300
400
500
diF /dt (A/μs)
diF /dt (A/μs)
Fig. 19 - Typical Stored Charge vs. dif/dt
Fig. 18 - Typical Recovery Current vs. dif/dt
180
160
QRR (nC)
140
120
IF = 144A
V R = 34V
TJ = 25°C
TJ = 125°C
100
80
60
40
20
100
200
300
400
500
diF /dt (A/μs)
www.irf.com
Fig. 20 - Typical Stored Charge vs. dif/dt
7
AUIRFS3004-7P
Driver Gate Drive
D.U.T
ƒ
-
‚
-
-
„
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
+

RG
dv/dt controlled by RG
Driver same type as D.U.T.
I SD controlled by Duty Factor "D"
D.U.T. - Device Under Test
VDD
P.W.
Period
VGS=10V
Circuit Layout Considerations
 Low Stray Inductance
Ground Plane
Low Leakage Inductance
Current Transformer
+
D=
Period
P.W.
+
+
-
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor
Current
Inductor Curent
ISD
Ripple  5%
* VGS = 5V for Logic Level Devices
Fig 21. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
V(BR)DSS
15V
DRIVER
L
VDS
tp
D.U.T
RG
VGS
20V
+
V
- DD
IAS
A
0.01
tp
I AS
Fig 22a. Unclamped Inductive Test Circuit
RD
VDS
Fig 22b. Unclamped Inductive Waveforms
VDS
90%
VGS
D.U.T.
RG
+
- VDD
V10V
GS
10%
VGS
Pulse Width µs
Duty Factor 
td(on)
Fig 23a. Switching Time Test Circuit
tr
t d(off)
Fig 23b. Switching Time Waveforms
Id
Current Regulator
Same Type as D.U.T.
Vds
Vgs
50K
12V
tf
.2F
.3F
D.U.T.
+
V
- DS
Vgs(th)
VGS
3mA
IG
ID
Current Sampling Resistors
8
Fig 24a. Gate Charge Test Circuit
Qgs1 Qgs2
Qgd
Qgodr
Fig 24b. Gate Charge Waveform
www.irf.com
AUIRFS3004-7P
D2Pak - 7 Pin Package Outline
Dimensions are shown in millimeters (inches)
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
www.irf.com
9
AUIRFS3004-7P
D2Pak - 7 Pin Part Marking Information
Part Number
AUS3004-7P
YWWA
IR Logo
XX
or
Date Code
Y= Year
WW= Work Week
A= Automotive, LeadFree
XX
Lot Code
D2Pak - 7 Pin Tape and Reel
Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/
10
www.irf.com
AUIRFS3004-7P
Ordering Information
Base part number
AUIRFS3004-7P
www.irf.com
Package Type
D2Pak 7 Pin
Standard Pack
Form
Tube
Tape and Reel Left
Tape and Reel Right
Complete Part Number
Quantity
75
800
800
AUIRFS3004-7P
AUIRFS3004-7TRL
AUIRFS3004-7TRR
11
AUIRFS3004-7P
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make
corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or
services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards
to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order
acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing
and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government
requirements, testing of all parameters of each product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR
components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all
associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice.
IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and
any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any
such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications
intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or
death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold
International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses,
and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product.
Only products certified as military grade by the Defense Logistics Agency (DLA) of the US Department of Defense, are designed and manufactured
to meet DLA military specifications required by certain military, aerospace or other applications. Buyers acknowledge and agree that any use of IR
products not certified by DLA as military-grade, in applications requiring military grade products, is solely at the Buyer’s own risk and that they are
solely responsible for compliance with all legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR
as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use
any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
101 N. Sepulveda Blvd., El Segundo, California 90245
Tel: (310) 252-7105
12
www.irf.com
Similar pages