H Features/Benefits • Traditional full profile DIP switch • Extended actuator for easy actuation • Open bottom construction allows for Typical Applications • Address switch for industrial controls • Logic switching for computers and DIP BD Series Standard Profile DIP Switches solder washing without the need for tape seal • RoHS compliant • Function controlling for peripherals numerous applications Specifications VIBRATION: No contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in DA or 5g, whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. SWITCH FUNCTION: SPST - 1 thru 12 position available (except 11 position). SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CONTACT RATING: PACKAGING: Switches supplied in rigid dispensing tubes in full-tube quantities only: this may effect order quantity. Number of switches per tube varies with model. Switch position 1 denotes pin number 1. All switch actuators in ‘OFF’ position, standard. Carry: 100 mA max. @ 50 V DC. Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC. MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break cycles at full load, each circuit. Materials CONTACT RESISTANCE: Below 50 milliohms typ. initial @ 2-4 V DC 100mA. CASE & COVER: Glass filled polyester (PBT), INSULATION RESISTANCE: 109 ohms min. flame retardant (UL 94V-0). DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between adjacent terminals. ACTUATOR: Glass filled nylon 6/6, flame retardant, CAPACITANCE: 5pF max. between adjacent terminals. CONTACTS: Gold over nickel over phosphor bronze. STORAGE & OPERATING TEMPERATURE: -40°C to 85°C. TERMINALS: Matte-tin over nickel over phosphor bronze. heat stabilized (UL 94V-0) SHOCK: Withstands 20g 11 ms sawtooth waveform with no contact opening greater than 10 microseconds. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Vertical Full Profile DIP PART NUMBER Ø.038 TYP. (0,97) .100 TYP. (2,54) .072 (1,83) ACTUATOR TRAVEL DIM 'A' O N .380 (9,65) BD08 .300 (7,62) 1 2 3 4 5 6 7 8 .160 TYP. (4,06) DIM 'B' .060 TYP. (1,52) .300 (7,62) .026 (0,66) .090 (2,29) .080 TYP. (2,03) .100 TYP. (2,54) .020 TYP. (0,51) .035 (0,9) TYP. .007 (0,18) BD01 BD02 BD03 BD04 BD05 BD06 BD07 BD08 BD09 BD10 BD12 NO.POS. DIM. ‘A’ QUANTITY PER TUBE 1 .180 (4,57) 115 2 .280 (7,11) 74 3 .380 (9,65) 54 4 .480 (12,19) 43 5 .580 (14,73) 35 6 .680 (17,27) 30 7 .780 (19,81) 26 8 .880 (22,35) 23 9 .980 (24,89) 21 10 1.080 (27,43) 19 12 1.280 (32,51) 16 Schematic SPST .300 (7,62) .141 TYP. (3,58) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–14 www.ck-components.com BD Series Standard Profile DIP Switches Open Base and AV Right Angle Terminal Style 0.050 (1,27) PART NUMBER 2 .280 (7,11) 72 3 .380 (9,65) 52 4 .480 (12,19) 42 NO.POS. 5 .580 (14,73) 35 6 .680 (17,27) 29 7 .780 (19,81) 26 8 .880 (22,35) 23 9 .980 (24,89) 20 10 1.080 (27,43) 18 12 1.280 (32,51) 15 Schematic .090 (2,29) 0.026 (0,66) H 0.300 (7,62) BD08AV 0.061 TYP. (1,55) .035 (0,9) TYP. DIM.A ON .080 (2,03) .380 (9,65) 1 .020 TYP. (0,51) 2 3 4 5 6 7 8 .125 (3,18) .100 TYP. (2,54) .007 (0,18) .100 (2,54) SPST .100 TYP. (2,54) .320 (8,13) .010 (0,25) .100 (2,54) .046 DIA TYP. (1,17ø) Installation, Soldering and Cleaning All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: 1) Wave soldering recommended at 500° F (260ºC) solder temperature. 2) Hand solder using 30 watt small tip iron controlled at 500° F (260ºC), 10 seconds max./terminal. 3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–15 www.ck-components.com DIP BD02AV BD03AV BD04AV BD05AV BD06AV BD07AV BD08AV BD09AV BD10AV BD12AV DIM. ‘A’ QUANTITY PER TUBE