SEMICONDUCTOR TECHNICAL DATA
#*#!' '
%"&$%"' '
' #!%"' "$('& " ('$('&
'' #"")%' "
The MC74LCX16373 is a high performance, non–inverting 16–bit
transparent latch operating from a 2.7 to 3.6V supply. The device is byte
controlled. Each byte has separate Output Enable and Latch Enable
inputs. These control pins can be tied together for full 16–bit operation.
High impedance TTL compatible inputs significantly reduce current
loading to input drivers while TTL compatible outputs offer improved
switching noise performance. A VI specification of 5.5V allows
MC74LCX16373 inputs to be safely driven from 5V devices.
The MC74LCX16373 contains 16 D–type latches with 3–state
5V–tolerant outputs. When the Latch Enable (LEn) inputs are HIGH, data
on the Dn inputs enters the latches. In this condition, the latches are
transparent, i.e., a latch output will change state each time its D input
changes. When LE is LOW, the latches store the information that was
present on the D inputs a setup time preceding the HIGH–to–LOW
transition of LE. The 3–state outputs are controlled by the Output Enable
(OEn) inputs. When OE is LOW, the outputs are enabled. When OE is
HIGH, the standard outputs are in the high impedance state, but this does
not interfere with new data entering into the latches.
•
•
•
•
•
•
•
•
•
LOW–VOLTAGE
CMOS 16–BIT
TRANSPARENT LATCH
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 1201–01
Designed for 2.7 to 3.6V VCC Operation
5.4ns Maximum tpd
5V Tolerant — Interface Capability With 5V TTL Logic
Supports Live Insertion and Withdrawal
IOFF Specification Guarantees High Impedance When VCC = 0V
LVTTL Compatible
LVCMOS Compatible
24mA Balanced Output Sink and Source Capability
Near Zero Static Supply Current in All Three Logic States (20µA)
Substantially Reduces System Power Requirements
• Latchup Performance Exceeds 500mA
• ESD Performance: Human Body Model >2000V; Machine Model >200V
PIN NAMES
Pins
Function
OEn
LEn
D0–D15
O0–O15
Output Enable Inputs
Latch Enable Inputs
Inputs
Outputs
11/96
Motorola, Inc. 1996
1
REV 1
MC74LCX16373
LOGIC DIAGRAM
1
OE1 1
48 LE1
O0 2
47 D0
O1 3
46 D1
GND 4
45 GND
O2 5
44 D2
O3 6
43 D3
VCC 7
42 VCC
O4 8
41 D4
O5 9
40 D5
39 GND
GND 10
O6 11
38 D6
O7 12
37 D7
O8 13
36 D8
O9 14
35 D9
GND 15
34 GND
O10 16
33 D10
O11 17
32 D11
VCC 18
31 VCC
O12 19
30 D12
O13 20
29 D13
GND 21
28 GND
O14 22
27 D14
O15 23
26 D15
OE2 24
25 LE2
Inputs
24
OE1
OE2
48
25
LE1
LE2
2
nLE
47
D0
D1
D2
O2
D3
O3
40
D5
O5
Q
D6
37
D7
O7
Q
26
D15
D
Outputs
22
Inputs
O14
Q
D
12
nLE
O13
Q
27
D14
D
20
nLE
nLE
O6
Q
O12
D
11
nLE
38
29
D13
D
19
Q
D
9
nLE
O11
Q
30
D12
D
17
nLE
nLE
O4
Q
O10
Q
D
8
nLE
D4
32
D11
D
16
nLE
D
6
Q
41
33
D10
nLE
O9
Q
D
5
Q
D
43
35
D9
nLE
14
nLE
O1
Q
D
44
D
3
nLE
46
O8
Q
36
D8
D
13
nLE
O0
Q
23
nLE
O15
Q
D
Outputs
LE1
OE1
D0:7
O0:7
LE2
OE2
D8:15
O8:15
X
H
X
Z
X
H
X
Z
H
L
L
L
H
L
L
L
H
L
H
H
H
L
H
H
L
L
X
O0
L
L
X
O0
H = High Voltage Level; L = Low Voltage Level; Z = High Impedance State; X = High or Low Voltage Level and Transitions Are Acceptable, for ICC
reasons, DO NOT FLOAT Inputs
MOTOROLA
2
LCX DATA
BR1339 — REV 3
MC74LCX16373
ABSOLUTE MAXIMUM RATINGS*
Symbol
Parameter
VCC
DC Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
Value
Condition
Unit
–0.5 to +7.0
V
–0.5 ≤ VI ≤ +7.0
V
–0.5 ≤ VO ≤ +7.0
Output in 3–State
V
–0.5 ≤ VO ≤ VCC + 0.5
Note 1.
V
IIK
DC Input Diode Current
–50
VI < GND
mA
IOK
DC Output Diode Current
–50
VO < GND
mA
+50
VO > VCC
mA
IO
DC Output Source/Sink Current
±50
mA
ICC
DC Supply Current Per Supply Pin
±100
mA
IGND
DC Ground Current Per Ground Pin
±100
mA
TSTG
Storage Temperature Range
–65 to +150
°C
* Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions
beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied.
1. Output in HIGH or LOW State. IO absolute maximum rating must be observed.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Operating
Data Retention Only
Min
Typ
Max
Unit
2.0
1.5
3.3
3.3
3.6
3.6
V
0
5.5
V
0
0
VCC
5.5
V
VCC
Supply Voltage
VI
Input Voltage
VO
Output Voltage
IOH
HIGH Level Output Current, VCC = 3.0V – 3.6V
–24
mA
IOL
LOW Level Output Current, VCC = 3.0V – 3.6V
24
mA
IOH
HIGH Level Output Current, VCC = 2.7V – 3.0V
–12
mA
IOL
LOW Level Output Current, VCC = 2.7V – 3.0V
12
mA
TA
Operating Free–Air Temperature
∆t/∆V
Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V,
VCC = 3.0V
(HIGH or LOW State)
(3–State)
–40
+85
°C
0
10
ns/V
DC ELECTRICAL CHARACTERISTICS
TA = –40°C to +85°C
Symbol
Characteristic
VIH
HIGH Level Input Voltage (Note 2.)
VIL
LOW Level Input Voltage (Note 2.)
VOH
HIGH Level Output Voltage
VOL
LOW Level Output Voltage
Condition
Min
2.7V ≤ VCC ≤ 3.6V
2.0
2.7V ≤ VCC ≤ 3.6V
Max
V
0.8
2.7V ≤ VCC ≤ 3.6V; IOH = –100µA
VCC – 0.2
VCC = 2.7V; IOH = –12mA
2.2
VCC = 3.0V; IOH = –18mA
2.4
VCC = 3.0V; IOH = –24mA
2.2
Unit
V
V
2.7V ≤ VCC ≤ 3.6V; IOL = 100µA
0.2
VCC = 2.7V; IOL= 12mA
0.4
VCC = 3.0V; IOL = 16mA
0.4
VCC = 3.0V; IOL = 24mA
0.55
V
2. These values of VI are used to test DC electrical characteristics only.
LCX DATA
BR1339 — REV 3
3
MOTOROLA
MC74LCX16373
DC ELECTRICAL CHARACTERISTICS (continued)
TA = –40°C to +85°C
Symbol
Characteristic
Condition
Min
Max
Unit
II
Input Leakage Current
2.7V ≤ VCC ≤ 3.6V; 0V ≤ VI ≤ 5.5V
±5.0
µA
IOZ
3–State Output Current
2.7 ≤ VCC ≤ 3.6V; 0V ≤ VO ≤ 5.5V;
VI = VIH or V IL
±5.0
µA
IOFF
Power–Off Leakage Current
VCC = 0V; VI or VO = 5.5V
10
µA
ICC
Quiescent Supply Current
2.7 ≤ VCC ≤ 3.6V; VI = GND or VCC
20
µA
2.7 ≤ VCC ≤ 3.6V; 3.6 ≤ VI or VO ≤ 5.5V
±20
µA
2.7 ≤ VCC ≤ 3.6V; VIH = VCC – 0.6V
500
µA
∆ICC
Increase in ICC per Input
AC CHARACTERISTICS (tR = tF = 2.5ns; CL = 50pF; RL = 500Ω)
Limits
TA = –40°C to +85°C
VCC = 3.0V to 3.6V
Symbol
Parameter
VCC = 2.7V
Waveform
Min
Max
Min
Max
Unit
tPLH
tPHL
Propagation Delay
Dn to On
1
1.5
1.5
5.4
5.4
1.5
1.5
5.9
5.9
ns
tPLH
tPHL
Propagation Delay
LE to On
3
1.5
1.5
5.5
5.5
1.5
1.5
6.4
6.4
ns
tPZH
tPZL
Output Enable Time to HIGH and
LOW Level
2
1.5
1.5
6.1
6.1
1.5
1.5
6.5
6.5
ns
tPHZ
tPLZ
Output Disable Time from HIGH and
LOW Level
2
1.5
1.5
6.0
6.0
1.5
1.5
6.3
6.3
ns
ts
Setup TIme, HIGH or LOW Dn to LE
3
2.5
2.5
ns
th
Hold TIme, HIGH or LOW Dn to LE
3
1.5
1.5
ns
tw
LE Pulse Width, HIGH
3
3.0
3.0
ns
tOSHL
tOSLH
Output–to–Output Skew
(Note 3.)
1.0
1.0
ns
3. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter
guaranteed by design.
DYNAMIC SWITCHING CHARACTERISTICS
TA = +25°C
Symbol
Characteristic
Condition
VOLP
Dynamic LOW Peak Voltage (Note 4.)
VCC = 3.3V, CL = 50pF, VIH = 3.3V, VIL = 0V
Min
Typ
0.8
Max
Unit
V
VOLV
Dynamic LOW Valley Voltage (Note 4.)
VCC = 3.3V, CL = 50pF, VIH = 3.3V, VIL = 0V
0.8
V
4. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW or LOW–to–HIGH. The remaining output is
measured in the LOW state.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
CIN
Input Capacitance
COUT
Output Capacitance
CPD
Power Dissipation Capacitance
MOTOROLA
Condition
Typical
Unit
VCC = 3.3V, VI = 0V or VCC
7
pF
VCC = 3.3V, VI = 0V or VCC
8
pF
10MHz, VCC = 3.3V, VI = 0V or VCC
20
pF
4
LCX DATA
BR1339 — REV 3
MC74LCX16373
2.7V
1.5V
Dn
1.5V
0V
tPLH
tPHL
VOH
1.5V
On
1.5V
VOL
WAVEFORM 1 – PROPAGATION DELAYS
tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns
2.7V
1.5V
OEn
2.7V
Dn
1.5V
1.5V
0V
tPZH
0V
ts
tPHZ
VCC
VOH – 0.3V LEn
1.5V
On
th
2.7V
tw
1.5V
1.5V
≈ 0V
0V
tPLH, tPHL
tPZL
tPLZ
≈ 3.0V
VOH
On
1.5V
1.5V
On
VOL
VOL + 0.3V
GND
WAVEFORM 3 – LE to On PROPAGATION DELAYS, LE MINIMUM
PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES
tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns except when noted
WAVEFORM 2 – OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 1. AC Waveforms
VCC
PULSE
GENERATOR
R1
DUT
CL
RT
TEST
6V
OPEN
GND
RL
SWITCH
tPLH, tPHL
Open
tPZL, tPLZ
6V
Open Collector/Drain tPLH and tPHL
6V
tPZH, tPHZ
GND
CL = 50pF or equivalent (Includes jig and probe capacitance)
RL = R1 = 500Ω or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
Figure 2. Test Circuit
LCX DATA
BR1339 — REV 3
5
MOTOROLA
MC74LCX16373
OUTLINE DIMENSIONS
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 1201–01
ISSUE A
48X
K
K1
K REF
0.12 (0.005)
M
T U
S
V
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
S
T U
S
J J1
48
25
SECTION N–N
M
0.254 (0.010)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSIONS A AND B ARE TO BE
DETERMINED AT DATUM PLANE –W–.
B
–U–
L
N
1
24
A
–V–
PIN 1
IDENT.
N
F
DETAIL E
D
C
M
0.25 (0.010)
–W–
0.076 (0.003)
–T– SEATING
DETAIL E
PLANE
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
12.40
12.60
6.00
6.20
–––
1.10
0.05
0.15
0.50
0.75
0.50 BSC
0.37
–––
0.09
0.20
0.09
0.16
0.17
0.27
0.17
0.23
7.95
8.25
0_
8_
INCHES
MIN
MAX
0.488
0.496
0.236
0.244
–––
0.043
0.002
0.006
0.020
0.030
0.0197 BSC
0.015
–––
0.004
0.008
0.004
0.006
0.007
0.011
0.007
0.009
0.313
0.325
0_
8_
H
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
Mfax: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MOTOROLA
6
MC74LCX16373/D
LCX DATA
BR1339 — REV 3