MC10EP16
Differential Receiver
The MC10EP16 is a differential receiver. The device is functionally
equivalent to the EL16 and LVEL16 devices with higher performance
capabilities. With output transition times significantly faster than the
EL16 and LVEL16, the EP16 is ideally suited for interfacing with high
frequency sources.
The EP16 provides a VBB output for either single-ended use or as a
DC bias for AC coupling to the device within the package. The VBB
pin should be used only as a bias for the EP16 as its current sink/source
capability is limited. Whenever used, the VBB pin should be bypassed
to ground via a 0.01µf capacitor.
•
•
•
•
•
•
•
•
•
•
•
•
160ps Propagation Delay
High Bandwidth to 3 GHz Typical
PECL mode: 3.0V to 5.5V VCC with VEE = 0V
ECL mode: 0V VCC with VEE = –3.0V to –5.5V
Internal Input Resistors: Pulldown on D, Pulldown and Pullup on D
Q Output will default LOW with inputs open or at VEE
ESD Protection: 4KV HBM, 200V MM
VBB Output
New Differential Input Common Mode Range
Moisture Sensitivity Level 1, Indefinite Time Out of Drypack.
For Additional Information, See Application Note AND8003/D
Flammability Rating: UL–94 code V–0 @ 1/8”,
Oxygen Index 28 to 34
Transistor Count: 167 devices
http://onsemi.com
8
1
SO–8
D SUFFIX
CASE 751
MARKING DIAGRAM
8
HEP16
ALYW
A
L
Y
W
1
*For additional information, see Application Note
AND8002/D
PIN DESCRIPTION
FUNCTION
PIN
NC
1
8
VCC
= Assembly Location
= Wafer Lot
= Year
= Work Week
D, D
ECL Data Inputs
Q, Q
ECL Data Outputs
VBB
Ref. Voltage Output
36.5k
D
2
7
Q
6
Q
75k
ORDERING INFORMATION
D
3
Device
75k
VBB
4
5
VEE
Package
Shipping
MC10EP16D
SOIC
98 Units/Rail
MC10EP16DR2
SOIC
2500 Tape & Reel
Figure 1. 8–Lead Pinout (Top View) and Logic Diagram
Semiconductor Components Industries, LLC, 1999
September, 1999 – Rev. 1.0
1
Publication Order Number:
MC10EP16/D
MC10EP16
MAXIMUM RATINGS*
Value
Unit
VEE
Symbol
Power Supply (VCC = 0V)
Parameter
–6.0 to 0
VDC
VCC
Power Supply (VEE = 0V)
6.0 to 0
VDC
VI
Input Voltage (VCC = 0V, VI not more negative than VEE)
–6.0 to 0
VDC
VI
Input Voltage (VEE = 0V, VI not more positive than VCC)
6.0 to 0
VDC
Iout
Output Current
50
100
mA
IBB
VBB Sink/Source Current{
± 0.5
mA
TA
Operating Temperature Range
–40 to +85
°C
Tstg
Storage Temperature
θJA
Thermal Resistance (Junction–to–Ambient)
θJC
Thermal Resistance (Junction–to–Case)
Tsol
Solder Temperature (<2 to 3 Seconds: 245°C desired)
Continuous
Surge
–65 to +150
°C
190
130
°C/W
41 to 44 ± 5%
°C/W
265
°C
Still Air
500lfpm
* Maximum Ratings are those values beyond which damage to the device may occur.
{ Use for inputs of same package only.
DC CHARACTERISTICS, ECL/LVECL (VCC = 0V; VEE = –5.5V to –3.0V) (Note 4.)
–40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
(Note 1.)
20
24
31
20
24
31
20
24
32
mA
VOH
Output HIGH Voltage
(Note 2.)
–1135
–1060
–885
–1070
–945
–820
–1010
–885
–760
mV
VOL
Output LOW Voltage
(Note 2.)
–1935
–1810
–1685
–1870
–1745
–1620
–1810
–1685
–1560
mV
VIH
Input HIGH Voltage
Single Ended
–1210
–885
–1145
–820
–1085
–760
mV
VIL
Input LOW Voltage
Single Ended
–1935
–1610
–1870
–1545
–1810
–1485
mV
VBB
Output Voltage Reference
–1510
–1310
–1445
–1245
–1385
–1185
mV
0.0
V
150
µA
VIHCMR Input HIGH Voltage Common Mode
Range (Note 3.)
IIH
Input HIGH Current
IIL
Input LOW Current
–1410
VEE+2.0
0.0
150
D
D
0.5
–150
–1345
VEE+2.0
0.0
150
0.5
–150
–1285
VEE+2.0
0.5
–150
µA
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained.
1. VCC = 0V, VEE = VEEmin to VEEmax, all other pins floating.
2. All loading with 50 ohms to VCC–2.0 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
4. Input and output parameters vary 1:1 with VCC.
http://onsemi.com
2
MC10EP16
DC CHARACTERISTICS, LVPECL (VCC = 3.3V ± 0.3V, VEE = 0V) (Note 8.)
–40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
(Note 5.)
20
24
31
20
24
31
20
24
32
mA
VOH
Output HIGH Voltage
(Note 6.)
2165
2240
2415
2230
2355
2480
2290
2415
2540
mV
VOL
Output LOW Voltage
(Note 6.)
1365
1490
1615
1430
1555
1680
1490
1615
1740
mV
VIH
Input HIGH Voltage
Single Ended
2090
2415
2155
2480
2215
2540
mV
VIL
Input LOW Voltage
Single Ended
1365
1690
1430
1755
1490
1815
mV
VBB
Output Voltage Reference
1790
1990
1855
2055
1915
2115
mV
3.3
2.0
3.3
2.0
3.3
V
150
µA
VIHCMR Input HIGH Voltage Common Mode
Range (Note 7.)
IIH
Input HIGH Current
IIL
Input LOW Current
1890
2.0
1955
150
D
D
0.5
–150
2015
150
0.5
–150
µA
0.5
–150
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained.
5. VCC = 3.0V, VEE = 0V, all other pins floating.
6. All loading with 50 ohms to VCC–2.0 volts.
7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
8. Input and output parameters vary 1:1 with VCC.
DC CHARACTERISTICS, PECL (VCC = 5.0V ± 0.5V, VEE = 0V) (Note 12.)
–40°C
Symbol
Characteristic
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
(Note 9.)
20
24
31
20
24
31
20
24
32
mA
VOH
Output HIGH Voltage
(Note 10.)
3865
3940
4115
3930
4055
4180
3990
4115
4240
mV
VOL
Output LOW Voltage
(Note 10.)
3065
3190
3315
3130
3255
3380
3190
3315
3440
mV
VIH
Input HIGH Voltage
Single Ended
3790
4115
3855
4180
3915
4240
mV
VIL
Input LOW Voltage
Single Ended
3065
3390
3130
3455
3190
3515
mV
VBB
Output Voltage Reference
3490
3690
3555
3755
3615
3815
mV
5.0
2.0
5.0
2.0
5.0
V
150
µA
VIHCMR Input HIGH Voltage Common Mode
Range (Note 11.)
IIH
Input HIGH Current
IIL
Input LOW Current
3590
2.0
150
D
D
0.5
–150
3655
150
0.5
–150
0.5
–150
3715
µA
NOTE: 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained.
9. VCC = 5.0V, VEE = 0V, all other pins floating.
10. All loading with 50 ohms to VCC–2.0 volts.
11. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
12. Input and output parameters vary 1:1 with VCC.
http://onsemi.com
3
MC10EP16
AC CHARACTERISTICS (VCC = 0V; VEE = –3.0V to –5.5V) or (VCC = 3.0V to 5.5V; VEE = 0V)
–40°C
Symbol
Characteristic
fmax
Maximum Toggle
Frequency (Note 13.)
tPLH,
tPHL
Propagation Delay to
Output Differential
tSKEW
Duty Cycle Skew (Note 14.)
tJITTER
Cycle–to–Cycle Jitter
VPP
Input Voltage Swing (Diff.)
Min
Typ
25°C
Max
Min
3.0
100
150
160
Typ
85°C
Max
3.0
240
240
5.0
5.0
20
TBD
TBD
1200
100
150
800
Typ
Max
3.0
160
800
Min
120
GHz
190
280
ps
5.0
20
ps
TBD
1200
150
Unit
800
ps
1200
mV
tr
Output Rise/Fall Times
Q
70
120
170
80
130
180
100
150
200
ps
tf
(20% – 80%)
13. Fmax guaranteed for functionality only. VOL and VOH levels are guaranteed at DC only.
14. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays
are measured from the cross point of the inputs to the cross point of the outputs.
http://onsemi.com
4
MC10EP16
PACKAGE DIMENSIONS
SO–8
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751–06
ISSUE T
D
A
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETER.
3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
C
5
0.25
H
E
M
B
M
1
4
h
B
e
X 45 _
q
A
C
SEATING
PLANE
L
0.10
A1
B
0.25
M
C B
S
A
S
DIM
A
A1
B
C
D
E
e
H
h
L
q
http://onsemi.com
5
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
4.80
5.00
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
MC10EP16
Notes
http://onsemi.com
6
MC10EP16
Notes
http://onsemi.com
7
MC10EP16
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
USA/EUROPE Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
Phone: 81–3–5487–8345
Email: [email protected]
Fax Response Line*: 303–675–2167
800–344–3810 Toll Free USA/Canada
ON Semiconductor Website: http://onsemi.com
*To receive a Fax of our publications
For additional information, please contact your local Sales Representative.
N. America Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
8
MC10EP16/D