Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Part No./型号：RGB Controller-303 User manual The remote controller is TTTa full color multifunctional RGB led controller based on PWM technology and is dedicated to control entire RGB color changes of LED lights with 4 wires(common anode),such as RGB led strip, led module, led spot lights, led wall-washer, led under water lamp and other led lights. It can be controlled both by remote controller and pressing buttons on the body panel .It has the characteristics of a high receiver sensitivity and excellent anti-interference ability. Meanwhile, its slim and delicate shape enables a no sweat installation and a simple operation. 1. Specifications Working temperature :-20～60℃ Supply voltage: DC 5～24V Product size: L210*W40*H30mm Package size: L295*W45*H35mm Changing mode: 29 modes Remote distance: 100m Color depth: Max.256 level per RGB. Bright adjust: 8 levels Speed adjust: 8 levels Net weigh: 175g Gross weight: 205g Output: Three CMOS drain-open output Max output current: 8A per channel 2. Features 1)Controlled both by remote controller and pressing buttons on the body panel, reliable control distance can reach as far as 100m without restriction of direction and obstacle. 2) Input Voltage range: DC 5～24V 3) 3-channel RGB full color control, max output current 8A per channel. 4) 29 modes of changing, such as static, gradual, jumpy etc., with color depth max 256 levels per RGB. 5) Speed and brightness of each mode is adjustable separately from 1-8 levels. 6) Can rest at current color and color depth. 7) Can restore to default settings by pressing RESET butto 3. Control Method Body Panel Remote control Controlled both by remote controller and pressing buttons on the body panel, function of each as below: www.ledz.com 1/3 Hebei I.T. (Shanghai) Co., Ltd. LED SPECIFICATION Button “ON/OFF”: Turn on/off the controller. Button “PAUSE”: Keep current status, press it again, will continue to change. Button “MODE+/M+”: Enter the next mode. Button “MODE -/M -”: Return to the previous mode. Button “SPEED/S”: Speed up/down color changing. (1～8 levels) Button “BRIGHT/B”: Adjust led brightness levels. (1～8 levels) Button “RESET”: Restore to default status if press this button over 3 seconds. 3. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pattern table status static red static green static blue static yellow static purple static cyan static white 3color jumpy changes 7color jumpy changes red stroboscopic green stroboscopic blue stroboscopic yellow stroboscopic purple stroboscopic cyan stroboscopic No. status 16 white stroboscopic 17 3color gradual changes 18 7color gradual changes 19 red,green gradual changes 20 green,blue gradual changes 21 red,blue gradual changes 22 red gradual bright&fade 23 green gradual bright&fade 24 blue gradual bright&fade 25 yellow gradual bright&fade 26 purple gradual bright&fade 27 cyan gradual bright&fade 28 white gradual bright&fade 29 mode cycle brt,speed(Dynamic) is valid 4. Safety Information 1. Please don’t install this controller in lightening, intense magnetic, humid and high-voltage fields. To reduce the risk of component damage and fire caused by short circuit, make sure correct connection and no 2. short circuit before power on. 3. Check if the voltage and power adapter suit the controller and if anode or cathode definition is the same as the controller’s. 4. If device has been damaged during transport, don’t take any action without contacting your supplier. If being used properly in accordance with the instruction, and quality problems occur, please contact local supplier too, we provide free repair or replacement services. 5. Conjunction Sketch Map Before installation and use, we strongly recommend you to read through this manual carefully. For update information, please consult with your supplier. www.ledz.com 2/3