HT7L4811 Non-isolation Buck LED Lighting Driver with Active PFC Features General Description • Tiny package SOT23-6 The HT7L4811 is a non-isolation buck PWM controller for LED lighting applications. The device has a fully integrated PFC circuit which operates in a boundary conduction mode (BCM) to achieve high power factor values. With good control over external MOSFETs, the device can easily meet exacting LED current and high power factor requirements. • Non-isolation buck topology • Low BOM Cost • Wide AC input range – from 85VAC to 265VAC • High Power Factor of >0.9 without additional circuitry • Accurate constant current (< ±3%) The HT7L4811 provides several protection functions, which include VCC Under Voltage Lockout (UVLO), Over Current Protection (OCP), Output LED String Open Protection, Output LED String Short Protection, VCC Over Voltage Protection (OVP) and Leading-Edge Blanking (LEB) for current sensing. Additionally and to ensure system reliability, the device includes a fully integrated thermal protection function. To protect the external power MOSFET from being damaged by a supply over voltage, the device DRV pin voltage is clamped to about 17V. • Low start-up current which reduces power dissipation • Full protection functions for enhanced safety ♦♦ Gate driver output voltage clamp ♦♦ VCC over voltage protection (VCC OVP) ♦♦ VCC under-voltage lockout with hysteresis (VCC UVLO) ♦♦ Output LED string over current protection ♦♦ Output LED string short protection ♦♦ Output LED string open protection ♦♦ On-chip over temperature protection (OTP) The high level of functional integration minimises the external component count giving major advantages in terms of cost and circuit board area. The device is supplied in a SOT23-6 package. Applications • General illumination • E26/27, T5/T8 LED Lamp • Other LED Lighting Applications Rev. 1.00 1 February 12, 2014 HT7L4811 Block Diagram DRV VCC Reference & Bias UVLO Driver Min Off Time VCC OVP ZCD ZCD Comparator Logic Control ZCD OVP OTP Starter OCP CS PWM Generator EA 0.2V LEB COMP GND Pin Assignment SOT23-6 COMP CS ZCD 7L4811 VCC Top View GND DRV Pin Description Pin No. Symbol 1 VCC Power supply pin 2 GND Ground pin 3 DRV Gate drive output for driving external power MOSFETs 4 ZCD 5 CS Current sense pin. A resistor is connected to sense the MOSFET current. 6 COMP Loop compensation pin. A capacitor is placed between COMP and GND. Rev. 1.00 Description Zero-current detect pin 2 February 12, 2014 HT7L4811 Absolute Maximum Ratings Input voltage to CS pin.............................. -0.3V to 6V Maximum current at ZCD pin.................3mA (source), 3mA (sink) Output voltage at COMP pin..................... -0.3V to 6V Maximum operating junction temperature.......... 150°C VCC supply voltage................................. -0.3V to 33V Storage temperature range................... -55°C to 150°C Note: These are stress ratings only. Stresses exceeding the range specified under ″Absolute Maximum Ratings″ may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Recommended Operating Ranges Operating junction temperature...........−40°C to 125°C VCC supply voltage....................................17V to 25V Electrical Characteristics Symbol Parameter VCC=18V, Ta=25°C Test Condition Min Typ Max Unit Power Supply (VCC Pin) VCCON UVLOON — — 18 — V VCCOFF UVLOOFF — — 10 — V VCCHYS UVLO Hysteresis — 7 — — V VOVP VCC OVP Trip Point — 26 29 32 V — 10 20 μA ISTART Start-up Current Before turn-on, @ VCC = UVLOON - 1V IQ Quiescent Current No switching — 0.6 1 mA ICC Operating Current @ 70kHz, Co=1nF — 1.8 3 mA 194 200 206 mV Error Amplifier VFB Feedback Reference Voltage Ta = 25°C Current Sense Comparator TLEB Leading Edge Blanking Time — — 400 — ns VCL Current Limit Threshold — — 1.3 — V Over Current Trip Point — — 0.9 — V Over Current Release Point — — 0.2 — V V VOCP Zero Current Detector VZCDH Upper Clamp Voltage IZCD = 300μA — 3 — VZCDL Lower Clamp Voltage IZCD = -2.5mA — -0.2 — V VZCDA Positive-Going Edge — — 1.5 — V VZCDT Negative-Going Edge — — 1 — V IOVP OVP Current on ZCD pin — 270 300 330 μA TB_OVP Blanking Time for OVP Detection — — 1 — μs TSTART Start Timer Period — — 40 — μs TOFF Minimum Off Time — — 4 — μs — — 150 — °C Starter Over Temperature Protection OTP Over Temperature Trip Point Gate Driver TR Rising Time CLOAD=1nF, 10%~90% — 100 — ns TF Falling Time CLOAD=1nF, 10%~90% — 70 — ns VG_CLAMP Gate Clamp Voltage @ VCC = 25V — 17 19.5 V Rev. 1.00 3 February 12, 2014 HT7L4811 Typical Performance Characteristics start up current (uA) 16 14 12 10 8 6 4 -40 -20 0 20 40 60 80 100 120 temperature (℃) Figure 1. Start-Up Current vs. Temperature operating current (mA) 2 1.95 1.9 1.85 1.8 1.75 1.7 1.65 1.6 -40 -20 0 20 40 60 temperature (℃) 80 100 120 Figure 2. Operation Current vs. Temperature 19 UVLO_on(V) 18.6 18.2 17.8 17.4 17 -40 -20 0 20 40 60 80 100 120 temperature (℃) Figure 3. UVLO_on vs. Temperature Rev. 1.00 4 February 12, 2014 HT7L4811 11 UVLO_off(V) 10.6 10.2 9.8 9.4 9 -40 -20 0 20 40 60 temperature (℃) 80 100 120 100 120 Figure 4. UVLO_off vs. Temperature 201 VFB (mV) 200.5 200 199.5 199 198.5 198 -40 -20 0 20 40 60 80 temperature (℃) Figure 5. VFB vs. Temperature 163.00 Iout (mA) 162.50 162.00 161.50 161.00 90Vac 115Vac 180Vac 240Vac 160.50 160.00 9S 10S 11S AC Input (VAC) 100Vac 135Vac 220Vac 265Vac 12S 13S Figure 6. Iout vs. LED(s) Regulation in E27 Bulb Rev. 1.00 5 February 12, 2014 HT7L4811 163.00 Iout (mA) 162.50 162.00 161.50 161.00 9S (162mA) 11S (162mA) 13S (162mA) 160.50 160.00 90 100 115 135 180 10S (162mA) 12S (162mA) 220 240 265 AC Input (VAC) Figure 7. Iout vs. Wide AC Voltage in E27(8W, 13S / 162mA) Bulb 89.0% 88.0% Efficiency 87.0% 86.0% 85.0% 84.0% 83.0% 9S (162mA) 11S (162mA) 13S (162mA) 82.0% 81.0% 10S (162mA) 12S (162mA) 80.0% 90 100 115 135 180 AC Input (VAC) 220 240 265 Power Factor (PF) Figure 8. Efficiency vs. Wide AC Voltage in E27(8W, 13S / 162mA) Bulb 1.000 0.980 0.960 0.940 0.920 0.900 0.880 0.860 0.840 0.820 0.800 9S (162mA) 11S (162mA) 13S (162mA) 90 100 115 10S (162mA) 12S (162mA) 135 180 AC Input (VAC) 220 240 265 Iout(mA) Figure 9. Power Factor (PF) vs. Wide AC Voltage in E27(8W, 13S / 162mA) Bulb 420 419 418 417 416 415 414 413 412 411 410 90Vac 115Vac 180Vac 240Vac LED 10S LED 11S 100Vac 135Vac 220Vac 265Vac LED 12S LED 13S LED 14S LED(S) Figure 10. Iout vs. LED(s) Regulation in T8 Tube Rev. 1.00 6 February 12, 2014 HT7L4811 420 419 418 Iout (mA) 417 416 415 414 413 412 LED 10S LED 11S 411 LED 13S LED 14S LED 12S 410 90 100 115 135 180 220 240 265 AC input (Vac) Figure 11. Iout vs. Wide AC Voltage in T8 (18W, 12S / 425mA*) Tube 89 Efficiency (%) 88 87 86 85 84 83 82 10S,414mA 12S,414mA 14S,414mA 81 11S,414mA 13S,414mA 80 90 100 115 135 180 220 240 265 AC input (Vac) Figure 12. Efficiency vs. Wide AC Voltage in T8(18W, 12S / 425mA) Tube 1.000 0.980 0.960 PF 0.940 0.920 0.900 10S,414mA 12S,414mA 14S,414mA 0.880 0.860 11S,414mA 13S,414mA 0.840 90 100 115 135 180 220 AC input (Vac) 240 265 Figure 13. Power Factor (PF) vs. Wide AC Voltage in T8(18W, 12S / 425mA) Tube Rev. 1.00 7 February 12, 2014 HT7L4811 25 THD(%) 20 15 10 5 E27 8W (13S, 162mA) T8 18W (12S, 425mA) 0 90 100 115 135 180 220 240 264 AC Input (VAC) Figure 14. E27/T8 THD vs. Wide AC Voltage Note: * 425mA is typical current limit. Actual LED current will be variable due to sense resistor tolerance. Typical Application Circuit LED+ 90Vac ~ 265Vac LED - DRV GND VCC HT7L4811 ZCD CS COMP Application Information Start-up Current The HT7L4811 is a universal AC/DC LED driver designed for LED lighting applications. The device can achieve high Power Factor values without resorting to additional circuits and can also generate high accuracy LED drive currents with very few external components. Separate grounds are provided; one is a floating ground for the HT7L4811 while the other one is the earth. Users should be aware that the two grounds cannot be directly connected together to avoid IC damage and system malfunction. A very low start-up current, ISTART, allows the users to select a larger value of start-up resistor which reduces power dissipation. Rev. 1.00 VCC Under Voltage Lockout – UVLO The device includes a UVLO feature which has 8V hysteresis. The PWM controller turns on when VCC is higher than 18V and turns off when VCC is lower than 10V. The hysteresis characteristics guarantee that the device can be powered by an input capacitor during start-up. When the output voltage increases to a certain value after start-up, VCC will be charged by an output through an auxiliary winding or a Zener Diode. VZ=VLED - VCC. 8 February 12, 2014 HT7L4811 Boundary Conduction Mode – BCM OVP on VCC – Over Voltage Protection The power MOSFET is turned on by inductor current zero-crossing detection. The current zero-crossing can be detected by a ZCD voltage. When the inductor current is at the zero crossing point, the voltage on the ZCD pin will drop rapidly. The HT7L4811 then detects the falling edge and turns on the Power MOSFET. The boundary conduction mode provides low turn-on switching losses and high conversion efficiency. In order to prevent PWM controller damage, the device includes an OVP function on VCC. Should the VCC voltage be higher than the OVP threshold voltage of 29V, the PWM controller will stop operating immediately. When the VCC voltage decreases below the UVLO off level, the controller will reset. Zero Current Detection – ZCD The LED voltage is reflected on the ZCD pin through a resistor RZCD. When the current on the resistor RZCD is higher than 300μA, then ZCD OVP protection will take place. Here the PWM controller will stop operating immediately. When the VCC voltage decreases below the UVLO off level, the controller will reset. LED Open Protection – ZCD OVP The ZCD voltage is designed to operate between 0V and 3V for normal operation. If the voltage on the ZCD pin goes higher than 1.5V, the ZCD comparator waits until the voltage goes below 1V. When the inductor current is at the zero crossing point, the voltage on the ZCD pin will drop rapidly. The device will then detect the 1V falling edge and turn on the Power MOSFET. The 0.5V hysteresis avoids any false triggering actions due to noise. VOVP-ZCD can be set using the following equation: VOVP−ZCD = VZCDH + IOVP × RZCD The VZCDH is the upper clamp voltage 3V on the ZCD pin. The IOVP represents the OVP current level on the ZCD pin which is 300μA. The RZCD stands for the resistor connected between the ZCD pin and the LED positive terminal. Constant Current Control The HT7L4811 will sense the overall inductor current and form a closed-loop with an internal error amplifier to obtain high constant current accuracy. The CS voltage and the 0.2V reference voltage are the inputs of a Gm amplifier whose output is integrated via an external COMP capacitor. The ON time of the MOSFET is controlled by the COMP voltage to adjust the output current. OCP – Over Current Protection The HT7L4811 includes an over current protection function on the CS pin. An internal circuit detects the current level and when the current is larger than the over current protection threshold level, VOCP/RCS, the gate output will remain at a low level. LEB on CS – Leading-Edge Blanking LED Short Protection – SCP Each time the external power MOSFET is switched on, a turn-on spike will inevitably occur at the sense resistor. To avoid faulty triggering, a 400ns leadingedge blank time is generated. As this function is provided conventional RC filtering is therefore unnecessary. During this blanking period, the currentlimit comparator is disabled and can therefore not switch off the gate driver. The output voltage drops when a number of LEDs in a string are shorted resulting in a voltage drop at VCC. Once the VCC drops below 10V, the device will stop operating. Under such situations, the start-up operation will recharge the VCC pin through the startup resistor and the device will enter the UVLO hiccup mode. Gate Driver Clamp Thermal Protection The DRV pin is connected to the gate of external MOSFET to control its ON/OFF function. To protect the external power MOSFET from being overstressed, the gate driver output is clamped to 17V. Rev. 1.00 A thermal protection feature is included to protect the device from excessive heat damage. When the junction temperature exceeds a threshold of 150°C, the thermal protection function will turn off the DRV terminal immediately. When the VCC decreases below the UVLO off level, the controller will reset. 9 February 12, 2014 HT7L4811 Package Information Note that the package information provided here is for consultation purposes only. As this information may be updated at regular intervals users are reminded to consult the Holtek website for the latest version of the package information. Additional supplementary information with regard to packaging is listed below. Click on the relevant section to be transferred to the relevant website page. • Further Package Information (include Outline Dimensions, Product Tape and Reel Specifications) • Packing Meterials Information • Carton information Rev. 1.00 10 February 12, 2014 HT7L4811 6-pin SOT23-6 Outline Dimensions Symbol Nom. Max. A — — 0.057 A1 — — 0.006 A2 0.035 0.045 0.051 b 0.012 — 0.020 0.009 C 0.003 — D — 0.114 BSC — E — 0.063 BSC — — e — 0.037 BSC e1 — 0.075 BSC — H — 0.110 BSC — L1 — 0.024 BSC — θ 0° — 8° Symbol Rev. 1.00 Dimensions in inch Min. Dimensions in mm Min. Nom. Max. A — — 1.45 A1 — — 0.15 A2 0.90 1.15 1.30 b 0.30 — 0.50 C 0.08 — 0.22 D — 2.90 BSC — E — 1.60 BSC — e — 0.95 BSC — e1 — 1.90 BSC — H — 2.80 BSC — L1 — 0.60 BSC — θ 0° — 8° 11 February 12, 2014 HT7L4811 Copyright© 2014 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek's products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.00 12 February 12, 2014