ROHM RPM5338-H14

RPM5300 series
Photo Link Module
IR Receiver Module
RPM5300 series
RPM5300 series are remote control receiver modules. Small-sized, light-weight, and low current consumption modules
have been achieved by using resin mold.
zApplications
All household electric appliances such as TV, DVD, air conditioner and audio equipment.
zFeatures
1) Small size, SMD type.
2) Low current consumption. (300µA Typ.)
3) High ripple rejection.
4) Top view package type & Side view package type.
5) High sensitivity, such as leed type IR Receiver, because of using “the Dual Receiving Lens”.
zRPM5300 series
Sub carrier frequency
SIDE VIEW
TOP VIEW
36.7kHz
RPM5337-H14
RPM5337-H12
37.9kHz
RPM5338-H14
RPM5338-H12
40.0kHz
RPM5340-H14
RPM5340-H12
zAbsolute maximum ratings (Ta = 25°C)
Symbol
Limits
Unit
Supply Voltage
Parameter
VCC
6.3
V
Storage temperature
Tstg
−30 to +100
°C
Operating temperature
Topr
−10 to +75
°C
zRecommended operating conditions (Ta = 25°C)
Parameter
Supply Voltage
Symbol
Min.
Typ.
Max.
Unit
VCC
2.7
3.0
3.6
V
1/7
RPM5300 series
Photo Link Module
zBlock diagram
VCC
100k
AMP
Comparator
LIMITER
ROUT
BPF
I/V
Demodulator
and integrator
GND
zTerminal description
Pin No.
Pin name
Function
POWER SUPPLY
1
VCC
2
GND
GROUND
3
GND
GROUND
4
GND
GROUND
5
ROUT
OUTPUT TERMINAL
6
GND
GROUND
7
GND
GROUND
zElectrical, Optical characteristics (Unless otherwise noted, Ta = 25°C VCC=5V)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Conditions
ICC
−
300
500
µA
No outside light, No signal input
Effective Distance
L
7
12
−
m
Outer light condition Ee < 10 (Ix)
High Level Output Voltage
VH
2.5
−
−
V
Low Level Output Voltage
VL
−
−
0.5
V
Isink <
= 200µA
∗1
ON Pulse Width
TON
400
600
800
µs
Outer light condition Ee < 10 (Ix)
∗1
OFF Pulse Width
TOFF
400
600
800
µs
Outer light condition Ee < 10 (Ix)
∗1
Center frequency
fo
−
∗3
−
kHz
Horizontal half angle
θ 1/2
−
42
−
deg
∗2
Vertical half angle
θ 1/2
−
38
−
deg
∗2
Consumption Current
∗1
∗1
∗1 600/600µs burst wave is transmitted by standard transmitter. However, it must be measured after the initial transmission pulse is 10 pulse.
∗2 It is an angle when the linear arrival distance become half.
∗3 Three types of frequencies : 36.7, 37.9, 40kHz.
2/7
RPM5300 series
Photo Link Module
z Measurement Conditions
(1) Transmit signal
600µs
600µs
Carrier frequency=fo, Duty=50%
Fig.1 Transmit signal
(2) Standard transmitter
λ peak=940nm
λ ∆=40nm
io=VOUT / R
20cm
RPM-302B
Standard transmitter
R
VOUT
Fig.2 Measurement of standard transmitter proofreading
When standard transmitter output the signal at Fig.1 standard photodiode output become io=5µAp-p under the
measurement condition Fig.2.
(The radiant intensity of standard transmitter : 50mW / sr)
RPM-302B : standard photodiode has short current Isc=27µA at E=1000(lx)
(using CIE standard light source A)
3/7
RPM5300 series
Photo Link Module
(3) Measurement effective distance, horizontal & vertical half angle
RPM5300 series
θ
θ
Standard transmitter
Light detector face
illuminance : Ee
Effective distance : L
(θ ; Indicates horizontal and vertical directions)
Fig.3 Measurement condition for effective distance
Effective distance L
Horizontal & vertical half angle θ
: Effective distance at θ=0° Fig.3
: The angle which effective distance became 50% of L.
(4) Output signal
600µs
600µs
Transmit signal
Carrier frequency=f0
Carrier Duty=50%
VCC
Output signal
VH
1/2 VCC
VL
GND
TOFF
TON
Fig.4
(5) Measurement circuit for the output voltage and the consumption current
ICC
VCC
A
ROUT
VCC
RPM5300
GND
V
VH , VL
Fig.5
4/7
RPM5300 series
Photo Link Module
zNotes
(1) All characteristics of the receiver in this specification are specified by supplying burst wave form (Fig.1) with ROHM
standard transmitter (Fig.2 ).
If in case of other burst wave form will be used, please check these spec. Carefully under the evaluations.
(2) When the receiver will be used as the wire-less remote controller, please use the signal method the signal format
which refer to “Measures to prevent mulfunctioning of IR remote-controlled electric home appliances”. (Published July
1987 by Association of Electric Home Appliances)
If using other signal method, signal format, (ex: signal format which not including the leader signal) the receiver might
have chances to miss-function.
(3) Please set up transmitter’s carrier frequency as same as the receiver’s f0 frequency. Otherwise error might be
occurred.
(4) If transmission signal has non-continues carrier, error might be occurred. Continuous carrier is necessary.
T1
T1≠T2
T2
(5) The receiver was designed to use as in-door use only.
Therefore, please understand that the receiver cannot cover all characteristics, in case of using it out-door.
(6) Noise environment (Light noise from inverter Lamp, and other kind of Lamps, Power ripple, electromagnetic noise from
power circuit, and etc) may cause a reduced effective distance.
(7) The receiver may not work properly if receiving signal judgement is done by single pulse due to the
surrounding / environmental noises.
To prevent such misjudgement, please make sure that the receiver is set up to work only when receiving
series of coded signal.
(8) Emitting unit (remote control transmitter) has to be considered about its emitting device function, characteristics and
characteristics of the receiver.
(9) Please connect ‘Holder’ on to the ‘Ground (GND)’ of PCB. If the holder is not connected to the GND, there is a
possibility of worsening the characteristics of product.
(10) Do not supply unnecessary stress to lead.
(11) Please pay careful attention to the lens.
It might have a chance to miss-function when the lens get dust or dirty. And also please do not touch the lens.
(12) In order to prevent products from ESD, human body and solder iron, etc. are required to be grounded.
5/7
RPM5300 series
Photo Link Module
zElectrical and optical characteristics curves
1.00
120
0.00
100
100
Relative effective distance : (%)
−2.00
fo=4
0.0kH
z
−6.00
fo=3
7.9kH
z
fo=3
6.7kH
z
Gain : (dB)
−4.00
−8.00
−10.00
80
60
40
20
0
34.00
36.00
38.00
40.00
−90 −75 −60 −45 −30 −15
42.00
Frequency : (kHz)
0
15
30
45
60
75
90
Angle : (˚)
Fig.6 BPF characteristic
Fig.7 Direction characteristic
(Horizontal direction)
120
Relative effective distance : (%)
100
80
60
40
20
0
−90 −75 −60 −45 −30 −15
0
15
30
45
60
75
90
Angle : (˚)
Fig.8 Direction characteristic
(Vertical direction)
6/7
RPM5300 series
Photo Link Module
zExternal dimensions (Unit : mm)
RSLP7A-H14
RSLP7A-H12
7.6
4.0
MOUNTING CENTER
3.0±0.1
0.6±0.1
1.0
MOUNTING CENTER
2.2
2.80
2.2
4.0
8.0
0.15±0.1
1.0
1.1
1.4
4.0
2.59
1.2
2.4
3.0
2.80
2.0
8.0
5.6
2.8
UNIT : mm
ETH672
0.6±0.1
0.15±0.1
NOTE
1.TOLERANCE : ±0.2mm
2.COPLANARITY : 0.1mmMAX
2.49
2.72
0.56
P0.95×7=6.65
0.2
0.6±0.1
0.48
0.37±0.1
0.68
0.75±0.1
0.37±0.1
0.95
P0.95×7=6.65
Expanded Figure of
A part
2.2
0.65±0.1
7
0.75
2.67
1
0.65
2.9
0.56
A
NOTE
TOLERANCE : ±0.2mm
COPLANARITY : 0.1mmMAX
UNIT : mm
ETH658
7/7
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1