SDKR Water-proof Type（with Built-in Detector Switches） Detector For power resume in main power auto shut down, compact and composite type suitable for AC and DC ■ Ratings and Safety Standards Items Specifications Slide AC Switch 1A 125V AC, 0.5A 250V AC （Resistive load） DC Switch 10mA 5V DC（Resistive load） Push Ratings satisfying local electrical appliance and material safety law 1A 125V AC Product Line Rotary Circuit arrangement Travel（mm） Operating force Mounting method SPST 1.5 2.5±1.5N PC board Minimum order unit（pcs.） Japan Export 150 3,000 Product No. SDKRA10100 Power Notes Dual-in-line Package Type 1. This product is not be used under water.（IP67 dust and water resistance） 2. Depending on the loading conditions, Nitrogen Oxide（NOx）and moisture caused by opening / closing arc may generate nitric acid（HNO3）. This can lead to corrosion of the metal inside causing functional failure. Please apply contact protection circuits （arc suppressing circuits） or an OFF stage arc reducing circuit method. Packing Specifications Tray Number of packages（pcs.） 1 case /Japan 1 case /export packing 750 Export package measurements（mm） 3,000 555×375×223 Push Type Dimensions Unit:mm PC board mounting hole dimensions （Viewed from the Direction A） Rocker Type Style Circuit Diagram （Viewed from Direction A） AC Switch DC Switch 15 15 1A125V~B Slide Type 0.5A250V~B Initial position On stroke Full stroke 1 1 1 b b a a R2 A 2.9 Momentary ø2.4 6.7 0.5 0.5 6 .2 ø1 4le ho 4.2 6 2.5 AC switch terminal No 1 10mA 5VDC 6 8 DC switch terminal Noa AC switch terminal No1 160 PC board mounting face le ø1.6 5.4 0.8 ø1 ho 0.5 8 1.6 3.5 13 3 10 0.8 8 .6 0.8 ø1 Rotary Type 13 (12.3) 11.5 9 1. C 1 4- DC switch terminal Nob Refer to P.176 for soldering conditions. Power Switches List of Varieties Type Push Detector Series Rocker SDKR SDDH SDKN 0.5A 250V AC 1A 125V AC 10mA 5V DC Rating（max.）:4.5A 12V DC （Lamp load: 27W×2） Rating（min.）:10ｍA 12V DC （Resistive load） 0.25A 250V AC 0.5A 125V AC 5mA 5V DC SDDJE ※ 1 SDDJF ※ 1 ※ 2 10AGP 250V AC 6A / 96A 250V〜 16AGP 250V AC 16（6）/ 250〜 ※2 Photo Slide Rating Push 100,000cycles Operating life 5,200cycles 10,000cycles 100,000 cycles 0.5A 250V AC 0.25A 250V AC 10A 250V AC 16A 250V AC Rotary Power Dual-in-line Package Type Travel（mm） 1.5 3.7 9 9.7 3.4 5.2 Features Water-proof type With signal circuit Water-proof (IP68 rating） — — — Operating temperature range −10℃ to ＋85℃ −15℃ to＋80℃ −20℃ to ＋60℃ Automotive use — ● — 100mΩ max.（ AC switch） 500mΩ max.（DC switch） 500mΩ max. 100mΩ max. 100mΩ max. 100MΩ min. 500V DC 500MΩ min. 500V DC −10℃ to ＋55℃ ○ ○ Life cycle (availability) Contact resistance Electrical performance Insulation resistance Push Type Voltage proof Terminal strength Rocker Type Mechanical performance Operating Actuator direction strength Perpendicular direction Slide Type Environmental performance 500MΩ min. 500V DC （AC switch） 10MΩ min. 500V DC 100MΩ min. 100V DC （DC switch） 1000V AC for 1minute （AC switch） 500V AC for 1minute 600V AC for 1minute 100V AC for 1minute （DC switch） 2,000V AC for 1minute Slider pull-out strength: 100N min. 50N for 1minute 50N for 1minute 60N for 1minute （Lead terminal） （Lead terminal） 5N for 1minute 10N for 1minute (Right-angle terminal) (Right-angle terminal) 20N 25N 30N 25N −30℃ 192h −20℃ 96h 5N for 1minute 100N 20N — — Rotary Type Cold −20℃ 240h −15℃ 96h Dry heat 85℃ 240h 80℃ 96h Damp heat 60℃, 90 to 95%RH 1000h Page 160 70℃ 192h 40℃, 90 to 95%RH 192h 161 162 85℃ 96h 40℃, 90 to 95%RH 96h 164 168 Power Switches Soldering Conditions・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 176 Power Switches Cautions・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 176 Power Switches Safety Standard・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 176 Notes 1. ※1. Dip soldering can be used on SDDJE for PC board terminal and SDDJF right angle terminal types only. 2. ※2. T he operating temperature range for automotive applications can be raised upon request. Please contact us for details. 3. ● Indicates applicability to all products in the series, while ○ indicates applicability to some products in the series. 158 Power Switches Soldering Conditions Detector Reference for Hand Soldering Reference for Dip Soldering Slide Soldering temperature Soldering time SDDJE, SDDJF, SDKP, SDDJF1A, SDKZ, SDDE 350±10℃ 3＋1/0s SDKR 300±10℃ 3±0.5s Series (For PC board terminal types and SDDJF right-angle terminal types) Series SDKR, SDDJE, SDDJF, SDKP, SDKZ, SDDE Dip soldering Soldering temperature Duration of immersion 260±5℃ 10±1s Push Power Switches Cautions Rotary Power Dual-in-line Package Type 1. The primary power supply switching is subject to the safety regulations, and the provisions differ by each destination. Consult with us for non-standard use cases. 2. An unstable contact may occur if the switch current is lower than 0.5A. For this case, consult with us. 3. These power switches were produced for alternating current. For direct current, consult with us. 4. Appling load to terminals during soldering under certain conditions may cause deformation and electrical property degradation. 5. Avoid use of water-soluble soldering flux, since it may corrode the switches. 6. When soldering twice, wait until the first soldered portion cools to normal temperature. Continuous heating will deform the external portions, loosen or dislodge terminals, or may deteriorate their electrical characteristics. 7. Before soldering switches with locking mechanism, release the locks. If they are soldered without releasing the locks, the soldering heat may deform the locking mechanism. 8. Be sure to release the locks before removing the knobs. Otherwise, the locking mechanism may be broken. 9. Be sure to use the switch with forced travel positioned as close to the total travel as possible. Push Type 10. Tighten the mounting screws by applying the specified torque. Tightening with a larger torque than the specified will result in malfunction or breakage of screws. 11. Corrosive gas if generated by peripheral parts of a set, malfunction such as imperfect contact may occur. Thorough investigation shall be required beforehand. 12. Storage Rocker Type Store the products as delivered at normal temperature and humidity, out of direct sunlight and away from corrosive gases. Use them as soon as possible and no later than six months after delivery. Once the seal is broken, use them as soon as possible. Slide Type Power Switches Safety Standards 1. Safety Standards Outline Rotary Type Safety standards are established by a country or an organization representing it to protect general users from electrical shock and fire hazards. It establishes standards for electrical devices and components. For electrical equipment manufacturers, utilizing switches that have been safety-approved ensures the safety of the switch. The use of a safety-approved switch also simplifies at least one part of the process of obtaining certification by safety testing. 2. Major Safety Standards Electrical Appliance and Material Safety Law （1） The conventional [Electrical Appliance and Material Control Law] has changed to [Electrical Appliance and Material Safety Law] and has been enforced since April 1, 2001. Electrical appliances are categorized into special electric appliances and parts（formerly Class A）and Electrical appliances other than the special electric appliances（formerly Class B）. Special electric appliances are required to receive goodness of fit test at a certified test agency and to store the certificate. Also, penal provisions have been reinforced. UL （2） （Underwriters Laboratories Inc.） Underwriters Laboratories Inc.（UL）is the American safety approving organization. Its purpose is to ensure consumer safety and protect them from fire hazards. State law requires that equipment to be exported to the United States utilize UL approved power switches or power switches meeting UL standards and capable of passing UL tests. 176