DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Applications Product Description The SE2521A60 is a complete 802.11 b/g WLAN RF front-end module providing all the functionality of the power amplifier, power detector, T/R switch, diversity switch and associated matching. The SE2521A60 provides a complete 2.4 GHz WLAN RF solution from the output of the transceiver to the antennas in an ultra compact form factor. IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN Access Points, PCMCIA, PC cards Features Pin for pin compatible to Skyworks’ SE2521A34 but providing 2 dB extra output power Dual Mode IEEE802.11b & IEEE802.11g All RF ports matched to 50 Ω Integrated PA, TX Filter, DPDT T/R and Diversity switches Integrated Power Detector 23 dBm O/P Power, 802.11b, 11 Mbits, ACPR <35 dBc 18 dBm @ 2.0 %, 802.11g, 54 Mbits Single supply voltage: 3.3 V ± 10 % Lead free and RoHS compliant Small lead free plated package, 8 mm x 7 mm x 1.1 mm, MSL 3 Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver RFIC. The SE2521A60 also includes a transmitter power detector with 20 dB of dynamic range and a digital enable control for transmitter power ramp on/off control. The power ramp rise/fall time is 1 μsec typical. The device also provides a notch filter from 3.2-3.3 GHz prior to the input of the power amplifier. The SE2521A60 is footprint compatible to Skyworks’ SE2521A34 and can be placed directly into existing SE2521A34 designs easily providing higher output power solutions Ordering Information Part No. Package Remark SE2521A60 SE2521A60-R SE2521A60-EK1 24 pin LGA 24 pin LGA N/A Samples Tape and Reel Evaluation kit Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Functional Block Diagram ANT_A VCC1 50 Ohm Match Bias Circuitry TXEN TXIN PD_OUT 50 Ohm Match OMN LPF Filter Power Detector 50 Ohm Match Switch Control C1 RXOUT 50 Ohm Match C2 C3 C4 ANT_B Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End GND GND GND ANT_A GND GND ANT_B Pin Out Diagram 24 23 22 21 20 19 18 3 15 C2 GND 4 14 C1 GND 5 13 PD_OUT 6 7 8 9 10 11 12 TXEN VCC1 N/C 16 C3 RX_OUT 2 GND VCC1 GND 17 C4 GND 1 TX_IN GND Figure 2: SE2521A60 Pin Out (Top View Through Package) Pin Out Description Pin No. Name Description 1 GND Ground 2 VCC1 +3.3 V DC 3 VCC1 +3.3 V DC 4,5 GND Ground 6 TX_IN 7,8,9 GND 10 RX_OUT 11 N/C Transmit Input Ground Receive Output No Connect 12 TXEN Transmit Enable 13 PD_OUT Power Detector 14 C1 Control 1 Input 15 C2 Control 2 Input 16 C3 Control 3 Input 17 C4 Control 4 Input 18 ANT_B Antenna B (50 ohm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Pin No. Name 19,20 GND 21 ANT_A 22,23,24 GND Description Ground Antenna A (50 ohm) Ground Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage on VCC -0.3 4.0 V TXEN Power Amplifier Enable -0.3 4.0 V TXRF RF Input Power - 2.0 dBm Operating Temperature Range -20 85 °C Storage Temperature Range -40 150 °C TA TSTG Recommended Operating Conditions Symbol Parameter VCC Supply Voltage TA Ambient Temperature Min. Typ. Max. Unit 3.0 3.3 3.6 V 0 25 85 °C DC Electrical Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol ICC-G Parameter Conditions Min. Typ. Max. Unit POUT = 18 dBm, 54 Mbps OFDM signal, 64QAM 165 180 230 mA POUT = 15 dBm, 54 Mbps OFDM signal, 64QAM 110 150 215 mA Total Supply Current ICC-B Total Supply Current POUT = 20 dBm, 11 Mbps CCK signal, BT = 0.45 175 205 275 mA ICC_OFF Total Supply Current VEN = 0 V, No RF Applied, C1 = C2 = C3 = C4 = 0 V - 2 10 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Logic Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage (Module On) - 2.0 - VCC V VENL Logic Low Voltage (Module Off) - 0 - 0.5 V IENH Input Current Logic High Voltage - -1 - 200 μA IENL Input Current Logic Low Voltage - -1 - 1 μA Switch Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VCTL_ON Control Voltage (On State) - 3.0 - 3.6 V VCTL_OFF Control Voltage (OFF State) - 0.0 - 0.2 V SW ON Low Loss Switch Control Voltage High State = VCTL_ON VCTL_OFF 2.8 - VCC V SW OFF High Loss Switch Control Voltage Low State = VCTL_OFF VCTL_OFF 0 - 0.3 V ICTL_ON Switch Control Bias Current (RF Applied) On pin (C1,C2,C3,C4) being driven high. RF Applied - - 100 µA ICTL_ON Switch Control Bias Current (No RF) On pin (C1,C2,C3,C4) being driven high. No RF - - 30 µA - - - 100 pF CCTL Control Input Capacitance Switch Control Logic Table Switch Logic Operational Mode C1 C4 C2 C3 TXRF – ANTA TXRF – ANTB RXRF – ANTA RXRF – ANTB SW ON SW OFF SW OFF SW OFF ON OFF OFF OFF SW OFF SW ON SW OFF SW OFF OFF ON OFF OFF Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Switch Logic Operational Mode C1 C4 C2 C3 TXRF – ANTA TXRF – ANTB RXRF – ANTA RXRF – ANTB SW OFF SW OFF SW ON SW OFF OFF OFF ON OFF SW OFF SW OFF SW OFF SW ON OFF OFF OFF ON AC Electrical Characteristics 802.11g Transmit Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN P802.11g P802.11b Parameter Frequency Range Condition Min. Typ. Max. Unit - 2400 - 2500 MHz Output power 54 Mbps OFDM signal, 64QAM, EVM = 2.0 % - 18 - dBm Output power 11 Mbps CCK signal, BT = 0.45 ACPR(Adj) < -32 ACPR(Alt) < -52 - 23 - dBm P1dB P1dB - 22.5 25.5 - dBm S21 Small Signal Gain - 25 - 33 dB Small Signal Gain Variation Over Band - - 1.0 3.0 dB Gain @ 3.2 to 3.3 GHz - - 0 7 dB Pout = 19 dBm, 2 Mbps, 802.11b CCK - -49 -42 dBm/MHz f1 and f2 at Fc +/- 312.5 kHz, P = 15 dBm - -40 -33 dBc ΔS21 S213.2 2f,3f Harmonics IM3 3 Order Intermodulation IM5 5 Order Intermodulation f1 and f2 at Fc +/- 312.5 kHz, P = 15 dBm - -55 -47 dBc Rise Time 10 % to 90% of final output power level - 0.12 0.5 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 1.0 μs S11 Input Return Loss 4.5 6.5 - dB rd th tr STAB Stability PIN ≤ -2 dBm Load VSWR = 6:1 All non-harmonically related outputs less than -50 dBc/1MHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Receive Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FOUT Parameter Frequency Range Condition Min. Typ. Max. Unit - 2400 - 2500 MHz 0.8 1.2 dB RXIL Insertion Loss - - RXRL Return Loss - - -15 -10 dB Delta Rx TRISOL-2 ANTRISOL Delta between Rx paths ANT_A to RX_OUT or ANT_B to RX_OUT - - 0.5 dB Rx Leakage C1 or C4 = SWON, C2 = C3 = SWOFF, Device transmitting 15 dBm @ ANTA or ANTB, Power measured @ RX_OUT -9 - 3 dBm Isolation between ANT_A and ANT_B to RX_OUT Small signal input into ANT_A or ANT_B, Device not transmitting, Power measured @ RX_OUT, C1 AND C4 = SWON, C2 and C3 = SWOFF 14 - 24 dB Power Detector Characteristics Conditions: VCC = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board (de-embedded to device), unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 2400 - 2500 MHz 0 - 20 dBm FOUT Frequency Range PDR Power detect range, peak power PDZLOAD DC load impedance - 1 - - Mohm PDVNoRF Output Voltage, POUT = No RF - 0.90 - 1.02 V PDVp18 Output Voltage, POUT = 18dBm - 0.44 - 0.66 V PDVp20 Output Voltage, POUT = 20dBm - 0.28 - 0.51 V LPF-3dB Power detect low pass filter -3dB corner frequency 270 330 400 KHz Measured at ANT_A or ANT_B PDZLOAD = >1 Mohm, PDCLOAD = 180 pF Note: Power detector internal impedance is 2.7 KOhm Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Power Detector Response Characteristic 1 0.9 0.8 0.7 VDET (V) 0.6 0.5 0.4 0.3 0.2 0.1 0 0 2 4 6 8 10 12 14 16 18 20 22 Output Power (dBm) Figure 3: SE2521A60 Power Detector Performance Curve Typical Performance Data (Ambient Temperature) Conditions: VCC = VEN = 3.3 V, Frequency = 2450 MHz, TA = 25 °C, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board , all unused ports terminated with 50 ohms, unless otherwise noted. 802.11g Typical Performance Conditions: 54Mbps 802.11g OFDM Signal 802.11g EVM vs. Output Pow er over Voltage (2450 MHz, 25 C) 802.11g EVM vs. Output Pow er over Frequency (25 C, 3.3V) 2400 MHz 2450 MHz 2.7 V 2500 MHz 3.3 V 3.6 V 4.5 4.5 4 4 3.5 3.5 3 EVM (%) EVM (%) 3.0 V 5 5 2.5 2 3 2.5 2 1.5 1.5 1 1 0.5 0.5 0 6 7 8 9 10 11 12 13 14 15 Output Pow er (dBm ) 16 17 18 19 20 0 6 7 8 9 10 11 12 13 14 15 16 Output Pow er (dBm ) 17 18 19 20 21 Figure 4: 802.11g Typical EVM Performance: (a) Over Frequency, (b) Over Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End 802.11g OFDM ICC vs. Output Pow er over Frequency (25 C, 3.3 V) 2400 MHz 2500 MHz 2450 MHz 220 ICC (mA) 200 180 160 140 120 100 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Pow er (dBm ) Figure 5: 802.11g Typical Current Consumption (ICC) Performance over Frequency 802.11b Typical Performance 802.11B ACPR-Adj vs. Output Pow er over Voltage (25 C, 2450 MHz, 802.11b 11 Mbps Signal) 2.7 V 3.0 V 3.3 V 802.11B ACPR-Alt vs. Output Pow er over Voltage (25 C, 2450 MHz, 802.11b 11Mbps Signal) 2.7 V 3.6 V -26 -40 -28 -45 ACPR (dBc) ACPR (dBc) -30 -32 -34 3.0 V 3.3 V 3.6 V -50 -55 -60 -36 -65 -38 -70 -40 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 10 27 11 12 13 14 15 Output Pow er (dBm ) 16 17 18 19 20 21 22 23 24 25 26 27 Output Pow er (dBm ) (a) (b) Figure 6: 802.11b Typical ACPR Performance (11 Mbps, CCK, BT = 0.45) (a) 802.11b ACPR-ADJ vs. POUT over Voltage and (b) 802.11b ACPR-ALT vs. POUT over Voltage 2nd, 3rd Harm onics vs. Output Pow er (25 C, 2450 MHz, 802.11b 1 Mbps CCK Signal) 2nd Harmonic 3rd Harmonic Harmonic Power (dBm/1MHz) -40 -45 -50 -55 -60 -65 -70 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Output Pow er (dBm ) Figure 7: 802.11b Typical Harmonic Performance (1 Mbps, CCK) CW Typical Performance Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End IMD3, IMD5 vs. Output Pow er (25 C, 2450 MHz, CW) IMD3 P1dB vs. Frequency (25 C, 3.3 V, CW) IMD5 P1dB -30 27 -40 26.5 Gain 33 32 -60 26 30 29 25.5 28 25 Gain (dB) P1dB (dBm) IMD (dBc) 31 -50 27 -70 24.5 -80 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26 24 2400 21 2420 2440 2460 Frequency (MHz) Output Pow er (dBm ) (a) 25 2500 2480 (b) Figure 8: Typical CW Performance (a) IMD3, IMD5 vs. Output Power, (b) P1dB, Gain vs. Frequency Detector Performance VDET vs. Output Pow er over Frequency (25 C, 3.3 V, CW) 2400 MHz 2450 MHz VDET vs. Output Pow er over Voltage (25 C, 2450 MHz, CW) 2.7 V 2500 MHz 1 3.0 V 3.3 V 3.6 V 1 0.9 0.9 0.8 0.8 VDET (V) VDET (V) 0.7 0.6 0.5 0.4 0.7 0.6 0.5 0.3 0.4 0.2 0.3 0.1 0.2 0 2 4 6 8 10 12 14 Output Pow er (dBm ) 16 18 20 22 0 2 4 6 8 10 12 14 16 18 20 22 Output Pow er (dBm ) (a) (b) Figure 9: Typical Power Detector Response: (a) Over Frequency, (b) Over Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 10 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Typical Performance Data (Over Temperature: -40 C, 25 C, 85 C) Conditions: VCC = VEN = 3.3 V, Frequency = 2450 MHz, as measured on Skyworks Solutions’ SE2521A60-EV1 evaluation board , all unused ports terminated with 50 ohms, unless otherwise noted. 802.11g Typical Performance Conditions: 54Mbps 802.11g OFDM Signal 802.11g EVM vs. Output Pow er over Tem perature, Voltage (2450 MHz) 802.11g EVM vs. Output Pow er over Frequency, Tem perature (3.3V) -40 C, 2450 MHz 25 C, 2450 MHz 85 C, 2450 MHz -40 C, 2.7 V 25 C, 2.7 V 85 C, 2.7 V -40 C, 2500 MHz 25 C, 2500 MHz 85 C, 2500 MHz 5 5 4.5 4.5 4 4 3.5 3.5 EVM (%) EVM (%) -40 C, 2400 MHz 25 C, 2400 MHz 85 C, 2400 MHz 3 2.5 -40 C, 3.0 V 25 C, 3.0 V 85 C, 3.0 V -40 C, 3.3 V 25 C, 3.3 V 85 C, 3.3 V -40 C, 3.6 V 25 C, 3.6 V 85 C, 3.6 V 3 2.5 2 2 1.5 1.5 1 1 0.5 0.5 0 0 6 7 8 9 10 11 12 13 14 15 16 Output Pow er (dBm ) 17 18 19 20 6 21 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Output Pow er (dBm ) Figure 10: 802.11g Typical EVM Performance: (a) Over Frequency and Temperature, (b) Over Voltage and Temperature 802.11g OFDM ICC vs. Output Pow er over Frequency, Term perature (3.3 V) -40 C, 2400 MHz 25 C, 2400 MHz 85 C, 2400 MHz -40 C, 2500 MHz 25 C, 2500 MHz 85 C, 2500 MHz -40 C, 2450 MHz 25 C, 2450 MHz 85 C, 2450 MHz 220 ICC (mA) 200 180 160 140 120 100 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Output Pow er (dBm ) Figure 11: 802.11g Typical Current Consumption (ICC) Performance over Frequency and Temperature Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 11 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End 802.11b Typical Performance 802.11B ACPR-Adj vs. Output Pow er over Voltage, Tem perature (2450 MHz, 802.11b 11 Mbps Signal) -40 C, 2.7 V 25 C, 2.7 V 85 C, 2.7 V -40 C, 3.0 V 25 C, 3.0 V 85 C, 3.0 V -40 C, 3.3 V 25 C, 3.3 V 85 C, 3.3 V 802.11B ACPR-Alt vs. Output Pow er over Voltage, Tem perature (2450 MHz, 802.11b 11Mbps Signal) -40 C, 3.6 V 25 C, 3.6 V 85 C, 3.6 V -26 -40 C, 3.0 V 25 C, 3.0 V -40 C, 3.3 V 25 C, 3.3 V -40 C, 3.6 V 25 C, 3.6 V 85 C, 2.7 V 85 C, 3.0 V 85 C, 3.3 V 85 C, 3.6 V -40 -28 -45 ACPR (dBc) ACPR (dBc) -40 C, 2.7 V 25 C, 2.7 V -30 -32 -34 -50 -55 -60 -36 -65 -38 -40 -70 15 16 17 18 19 20 21 22 23 24 25 15 16 17 18 19 20 21 22 23 24 25 Output Pow er (dBm ) Output Pow er (dBm ) (a) (b) Figure 12: 802.11b Typical ACPR Performance over Voltage and Temperature (11 Mbps, CCK, BT = 0.45) (a) 802.11b ACPR-ADJ vs. POUT and (b) 802.11b ACPR-ALT vs. POUT 3rd Harm onic vs. Output Pow er over Tem perature (3.3 V, 2450 MHz, 802.11b 1Mbps CCK Signal) 2nd Harm onic vs. Output Pow er over Tem perature (3.3 V, 2450 MHz, 802.11b 1Mbps CCK Signal) -40 C 25 C -40 C 85 C 85 C -35 -45 Harmonic Power (dBm/1MHz) Harmonic Power (dBm/1MHz) 25 C -30 -40 -50 -55 -60 -65 -40 -45 -50 -55 -60 -65 -70 -75 -70 -80 10 11 12 13 14 15 16 17 18 19 Output Pow er (dBm ) 20 21 22 23 24 25 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Output Pow er (dBm ) Figure 13: 802.11b Typical Harmonic Performance over Temperature (1 Mbps, CCK) (a) 2 Harmonic nd Harmonic (b) 3 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 rd 12 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End CW Typical Performance P1dB vs. Frequency over Tem perature (3.3 V, CW) 25 C -40 C Sm all Signal Gain vs. Frequency over Tem perature (3.3 V, CW) -40 C 85 C 27 25 C 85 C 33 32 26.5 Gain (dBm) P1dB (dBm) 31 26 25.5 30 29 28 25 27 24.5 26 24 2400 2420 2440 2460 Frequency (MHz) 2480 25 2400 2500 2420 2440 2460 2480 2500 Frequency (MHz) (a) (b) Figure 14: Typical CW Performance over Temperature (a) P1dB vs. Frequency, (b) Gain vs. Frequency IMD3 vs. Output Pow er over Tem perature (2450 MHz, 3.3 V, CW) 25 C, IMD3 IMD5 vs. Output Pow er over Tem perature (2450 MHz, 3.3 V, CW) -40 C, IMD5 85 C, IMD3 -30 -30 -40 -40 IMD (dBc) IMD3 (dBc) -40 C, IMD3 -50 85 C, IMD5 -50 -60 -60 -70 -70 -80 25 C, IMD5 -80 6 7 8 9 10 11 12 13 14 15 Output Pow er (dBm ) (a) 16 17 18 19 20 21 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Output Pow er (dBm ) (b) Figure 15: Typical CW Performance over Temperature (a) IMD3 vs. Output Power, (b) P1dB vs. Frequency Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 13 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Typical Power Detector Performance Pow er Detector Response over Tem perature, Voltage (2450 MHz) SE2521A60 Power Detector Response over Temperature and Frequency -40C, 2400 MHz 25C, 2400 MHz 85C, 2400 MHz -40C, 2450 MHz 25C, 2450 MHz 85C, 2450 MHz -40 C, 2.7 V 25 C, 2.7 V 85 C, 2.7 V -40C, 2500 MHz 25C, 2500 MHz 85C, 2500 MHz 1 -40 C, 3.6 V 25 C, 3.6 V 85 C, 3.6 V -40 C, 3.3 V 25 C, 3.3 V 85 C, 3.3 V 1 0.9 0.9 0.8 0.8 0.7 VDET (V) VDET (V) -40 C, 3.0 V 25 C, 3.0 V 85 C, 3.0 V 0.6 0.7 0.6 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Output Pow er (dBm ) Output Pow er (dBm ) (a) (b) Figure 16: Typical Power Detector Response: (a) Over Frequency and Temperature, (b) Over Voltage and Temperature Package Information Figure 17 shows the detailed device package diagram. The pads on the Skyworks RF modules are plated with gold over nickel, with a gold thickness of approx. 0.75 to 1.0 um. The modules can be reflowed onto FR4 based material using eutectic Pb based or common tin based Pb free solder pastes. 5 4 3 2 1 6 1 GND GND GND GND 2 3 4 GND GND GND 6 GND GND 7 GND GND GND GND GND 8 GND GND GND GND GND 8 9 21 21 10 7 GND 22 22 9 GND 23 23 GND 20 20 10 GND GND GND 5 24 24 GND GND GND 19 19 11 11 GND GND GND GND GND GND 13 14 15 16 17 GND GND 16 15 14 GND 18 18 12 GND 12 17 13 TOP SIDE NOTES : GROUND PAD DETAIL SIGNAL PAD DETAIL BOTTOM SIDE Figure 17: SE2521A60 Package Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 14 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2521A60 is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Land Grid Array Module Solder Reflow & Rework Information”, Document Number QAD-00046 “Handling, Packing, Shipping and Use of Moisture Sensitive LGA”, Document Number QAD-00047 Recommended PCB Footprint Figure 18 shows the recommended PCB footprint for the SE2521A60. LAND PATTERN MASK PATTERN GROUND PAD DETAIL SIGNAL LAND DETAIL VIA IN SIGNAL LAND TABLE PIN NAME DESCRIPTION RECOMMENDED NOTES : RECOMMENDED FOOTPRINT LGA100P800X700-24-610X505 PASTE SCREEN PATTERN 01 Figure 18: SE2521A60 Recommended PCB Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 15 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Branding Information The device branding is shown in Figure 19. Pin 1 Identifier Terminal Finish Pin 1 Part Number SiGe 2521A60 Lot Code Lot Code e4 Figure 19: SE2521A60 Branding and Pin 1 Location Tape and Reel Production quantities of this product are shipped in a standard tape-and-reel format. dimensions and sizing is shown in Table 1 and Figure 20. Parameter Devices Per Reel Reel Diameter Specific tape and reel Value 2500 13 inches Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 16 DATA SHEET SE2521A60: 2.4 GHz Wireless LAN Front-End Table 1: Tape and Reel Dimensions Figure 20: SE2521A60 Tape and Reel Information Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202416A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 17