202451A.pdf

DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Applications
Product Description





The SE5502L is a complete 802.11a/b/g/n WLAN RF
front-end module providing all the functionality of the
power amplifiers, filtering, power detector, T/R switch,
diplexers, LNA and associated matching. The
SE5502L provides a complete 2.4 GHz and 5 GHz
WLAN RF solution from the output of the transceiver
to the antenna in an ultra compact form factor.
IEEE802.11b DSSS WLAN
IEEE802.11g OFDM WLAN
IEEE802.11a OFDM WLAN
IEEE802.11n WLAN
Access Points, PCMCIA, PC cards
Features









All RF ports matched to 50 Ω
Integrated 2.4 GHz PA, 5 GHz PA, T/R switch,
2.5GHz LNA, 5GHz LNA
Integrated Power Detector for each TX Chain
21 dBm O/P Power, 802.11b, 11 Mbits, ACPR =
35 dBc
18 dBm @ 3.0 % EVM, 802.11g, 54 Mbits
16 dBm @ 3.0 % EVM, 802.11a, 54 Mbits
Single supply voltage: 3.3 V ± 10 %
Lead free, Halogen free, RoHS compliant, MSL 1
4mm x 4mm x 0.9mm, QFN Package
Designed for ease of use, all RF ports are matched to
50 Ω to simplify PCB layout and the interface to the
transceiver RFIC. The SE5502L also includes a
transmit power detector with 20 dB of dynamic range
for each transmit chain. Each transmit chain has a
separate digital enable control for transmitter power
ramp on/off control. The power ramp rise/fall time is
less than 0.7 μsec.
The device also provides a notch filter from 3.2603.267 GHz and 3.28-3.89 GHz prior to the input of
each 2.4 GHz and 5 GHz power amplifiers,
respectively.
The SE5502L packaged in 4mm x 4mm x 0.9mm,
Halogen free, Lead free, ROHS compliant, MSL 3
QFN package.
Ordering Information
Part No.
Package
Remark
SE5502L
SE5502L-R
SE5502L-EK1
24 pin QFN
24 pin QFN
N/A
Samples
Tape and Reel
Evaluation kit
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
1
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Functional Block Diagram
C0
C1
Decode
2GHz
LNA
Rg
SP3T
Switch
Ra
2GHz
PA
Tg
Det
Ta
ANT
5GHz
LNA
Filter
TX
Diplexer
Detector
5GHz
PA
ENa
Filter
ENg
Figure 1: SE5502L Functional Block Diagram
Pin Out Diagram
Figure 2: SE5502L Pin Out (Top View Through Package)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
2
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Pin Out Description
Pin No.
Name
1
C0
2
Description
Pin No.
Name
Description
Switch Control
13
GND
Ground
Rg
2.4 GHz RF Receive Output
14
GND
Ground
3
Ra
5 GHz RF Receive Output
15
GND
Ground
4
Tg
2.4 GHz RF Transmit Input
16
GND
Ground
5
Ta
5 GHz RF Transmit Input
17
ANT
Antenna
6
Det
2.4/5 GHz Power Detector Output
18
GND
Ground
7
ENa
5 GHz Power Amplifier Enable
19
GND
Ground
8
ENg
2.4 GHz Power Amplifier Enable
20
GND
Ground
9
VCC
Supply Voltage
21
GND
Ground
10
VCC
Supply Voltage
22
GND
Ground
11
VCC
Supply Voltage
23
VCC
Supply Voltage
12
VCC
Supply Voltage
24
C1
Switch Control
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected
workstations.
Symbol
Definition
Min.
Max.
Unit
VCC
Supply Voltage
-0.3
3.6
V
PU
ENa, ENg, C0, C1
-0.3
3.6
V
-
12.0
dBm
Operating Temperature Range
-40
85
°C
TSTG
Storage Temperature Range
-40
150
°C
ESD HBM
JEDEC JESD22-A114 all pins
-
1000
V
TXRF
TA
Ta, Tg, ANT terminated in 6:1 load or better
Recommended Operating Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
VCC
Supply Voltage
3.0
3.3
3.6
V
TA
Ambient Temperature
-40
25
85
°C
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
3
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
DC Electrical Characteristics
Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5502L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted
Symbol
Parameter
ICC-G
Total 802.11g Transmit
Supply Current
Conditions
Min.
Typ.
Max.
Unit
POUT = 18 dBm, 54 Mbps
OFDM signal, 64 QAM
ENg = 3.3 V, ENa = 0 V,
100% duty cycle
-
150
-
mA
ICC-B
Total 802.11b Transmit
Supply Current
POUT = 21 dBm, 11 Mbps
CCK signal, BT = 0.45,
ENg = 3.3 V, ENa = 0 V,
100% duty cycle
-
175
-
mA
ICC-A
Total 802.11a Transmit
Supply Current
POUT = 16 dBm, 54 Mbps
OFDM signal, 64 QAM,
ENa = 3.3 V, ENg = 0 V,
100% duty cycle
-
210
-
mA
Icc-Rxa
Total Icc in Rx 5G band
5G LNA enabled
-
19
-
mA
Icc-Rxg
Total Icc in Rx 2G band
2G LNA enabled
-
18
-
mA
ICC_OFF
Total Supply Current
No RF, ENg = ENa = 0 V
-
50
180
μA
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
4
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
PA Logic Characteristics
Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5502L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
VENH
Logic High Voltage for ENg,
ENa (Module On)
-
1.8
-
VCC
V
VENL
Logic Low Voltage ENg,
ENa (Module Off)
-
0
-
0.4
V
IENH
Input Current Logic High
Voltage (ENg, ENa)
-
-
50
400
μA
IENL
Input Current Logic Low
Voltage (ENg, ENa)
VCC = 0.4V
-
0
40
μA
Switch/LNA Logic Characteristics
Conditions: VCC = 3.3 V, VEN = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5502L-EV1 evaluation
board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
VCTL_ON
Control Voltage C0, C1
(On State)
-
3.0
-
3.6
V
VCTL_OFF
Control Voltage C0, C1
(OFF State)
-
0.0
-
0.4
V
ICTL_ON
Switch Control Bias
Current (RF Applied)
On pin (TX, RX) being
driven high. RF Applied
-
-
100
µA
ICTL_ON
Switch Control Bias
Current (No RF)
On pin (TX, RX) being
driven high. No RF
-
-
30
µA
Switch & LNA Control Logic Table
C0
C1
EnG
EnA
Tg ↔ ANT
Ta ↔ ANT
Rg ↔ ANT
Ra ↔ ANT
VCTL_OFF
VCTL_OFF
VENH
VENL
ON
OFF
OFF
OFF
VCTL_OFF
VCTL_OFF
VENL
VENH
OFF
ON
OFF
OFF
VCTL_OFF
VCTL_ON
VENL
VENL
OFF
OFF
LNA Bypass ON
LNA Bypass ON
VCTL_ON
VCTL_OFF
VENL
VENL
OFF
OFF
OFF
LNA ON
VCTL_ON
VCTL_ON
VENL
VENL
OFF
OFF
LNA ON
OFF
VCTL_OFF
VCTL_OFF
VENL
VENL
All Other States
Stand By Mode, PAs and LNAs OFF – Low Current Consumption
Not Supported
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sal[email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
5
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
2.4 GHz AC Electrical Characteristics
2.4 GHz Transmit Characteristics
Conditions: VCC = 3.3 V, ENg = 3.3 V, ENa = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’
SE5502L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
Parameter
Frequency Range
Condition
Min.
Typ.
Max.
Unit
-
2400
-
2500
MHz
P802.11g
Output power
54 Mbps OFDM signal, 64QAM,
EVM = 3.0 %
-
18
-
dBm
P802.11b
Output power
11 Mbps CCK signal, BT = 0.45
ACPR(± 11MHz offset) < -35
ACPR(± 22MHz offset) < -56
-
21
-
dBm
P1dB
P1dB
-
23
25.5
-
dBm
S21
Small Signal Gain
-
25
28
30
dB
Small Signal Gain
Variation Over Band
-
-
1.0
2.0
dB
ΔS21
S213.2
Gain at Ref-VCO
3200.00 to 3300.00 MHz
-
-
0
dB
2f,3f
Harmonics
Pout ≤ 21 dBm typ, 1Mbps, CCK
-
-
-45.2
dBm/MHz
tr
Rise Time
10 % to 90% of final output
power level
-
-
0.5
μs
tdr, tdf
Delay and rise/fall
Time
50 % of VEN edge and 90/10 %
of final output power level
-
-
0.5
μs
S11
Input Return Loss
8
10
-
dB
STAB
Ru
-
Stability
CW, POUT = 21 dBm
0.1 GHz – 21 GHz
Load VSWR = 6:1
Ruggedness
Tg = 12dBm, ANT load varies
over 6:1 VSWR
All non-harmonically related outputs less
than -42 dBm/MHz
No Irreversible damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
6
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
2.4 GHz Receive Characteristics
Conditions: VCC = C0 = C1 = 3.3 V, ENg = ENa = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5502LEV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FOUT
Parameter
Condition
Min.
Typ.
-
2400
-
2500
MHz
10
15
-
dB
Frequency Range
Max.
Unit
Receive Gain, LNA
Enabled.
2400 – 2485 MHz
Receive Gain,
Bypass mode
C0 = 0 V; C1 = 3.3 V
2400 – 2485 MHz
-
-7.5
-
dB
Gain Variation
2400 – 2485 MHz, Over
any 40MHz band
-
0.25
0.5
dB
NF
Noise Figure
De-embedded to device
-
2.5
2.8
dB
INT
Interferer
@1710-1990MHz
With this input , IIP3 can
only degrade by 1dB
-10
-
-
dBm
S11
Input Return Loss
-
8
-
dB
S21
ΔS21
IP1dB
TEN
-
Input P1dB
C0 = 3.3 V
-
-7
-
dBm
Enable Time
10% to 90% of RX RF
power, from time that C0
is at 50%
-
500
-
nsec
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
7
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
5 GHz AC Electrical Characteristics
5 GHz Transmit Characteristics
Conditions: VCC = 3.3 V, ENa = 3.3 V, ENg = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’
SE5502L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FIN
P802.11a
Parameter
Frequency Range
Nominal Output Power
Condition
Min.
Typ.
Max.
Unit
-
4900
-
5875
MHz
54 Mbps OFDM signal, 64
QAM, EVM = 3.0 %
-
16
-
dBm
P1dB
P1dB
-
21
22.5
-
dBm
S21
Small Signal Gain
-
24
-
32
dB
Small Signal Gain Variation Over 40 MHz Channel
-
-
0.5
dB
Small Signal Gain
Variation Over subbands
-
-
3
dB
ΔS21
S213.2
Gain
3280 to 3900 MHz
-
3
9
dB
2f,3f
Harmonics
Pout ≤ 16 dBm typ,
54Mbps, 802.11a OFDM
-
-
-45.2
dBm/MHz
tr
Rise Time
10 % to 90% of final
output power level
-
-
0.5
μs
tdr, tdf
Delay and rise/fall
Time
50 % of VEN edge and
90/10 % of final output
power level
-
-
0.5
μs
S11
Input Return Loss
5
7
-
dB
STAB
Ru
-
Stability
64 QAM, POUT = 16 dBm
0.1 GHz – 21 GHz
Load VSWR = 6:1
All non-harmonically related outputs less than
-42 dBm/MHz
Ruggedness
TXa = 12dBm, ANT load
varies over 6:1 VSWR
No Irreversible damage
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
8
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
5 GHz Receive Characteristics
Conditions: VCC = C0 = 3.3 V, ENg = ENa = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5502LEV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
FOUT
Parameter
Condition
Min.
Typ.
-
4900
-
5850
MHz
10
12
-
dB
Frequency Range
Max.
Unit
Receive Gain
4900 – 5850 MHz
Receive Gain,
Bypass mode
C0 = 0.0 V; C1 = 3.3V
-
-20
-
dB
Gain Variation
4900 – 5850 MHz, Over
any 40MHz band
-
1
-
dB
NF
Noise Figure
De-embedded to device
-
2.8
3.0
dB
S11
Return Loss
10
15
-
dB
IP1dB
Input P1dB
C0 = 3.3 V
-6.5
-
-
dBm
Enable Time
10% to 90% of RX RF
power, from time that C0
is at 50%
-
500
-
nsec
S21
ΔS21
TEN
-
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
9
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
2.4 GHz Power Detector Characteristic
Conditions: VCC = 3.3 V, ENg = 3.3 V, ENa = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’
SE5502L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
PDR
Power detect range,
peak power
Condition
Min.
Typ.
-
2400
-
2500
MHz
0
-
22
dBm
Measured at ANT0 or
ANT1
Max.
Unit
PDZOUT
DC Output impedance
-
-
2.7
3
kΩ
PDVP21
Output Voltage, POUT =
21dBm
-
-
0.85
-
V
PDVp18
Output Voltage, POUT =
18dBm
-
-
0.65
-
V
PDVpnoRF
Output Voltage, POUT =
No RF
-
-
0.35
-
V
LPF-3dB
Power detect low pass
filter -3dB corner
frequency
-
1500
-
kHz
Load = high impedance
Typ: 500 kΩ
2.5GHz Pow er Detector Response into 1MΩ Load
2400
2450
2500
VDET (V)
1.1
0.9
0.7
0.5
0.3
3
5
7
9
11
13
15
17
Output Pow er (dBm )
19
21
23
Figure 3: SE5502L Power Detector vs. Output Power over Frequency (CW Signal)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
10
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
5 GHz Power Detector Characteristic
Conditions: VCC = 3.3 V, ENa = 3.3 V, ENg = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’
SE5502L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted.
Symbol
Parameter
FOUT
Frequency Range
PDR
Power detect range,
peak power
Condition
Min.
Typ.
-
4900
-
5850
MHz
0
-
21
dBm
Measured at ANT
Max.
Unit
PDZOUT
DC Output impedance
-
-
2.7
3.0
kΩ
PDVp18
Output Voltage, POUT =
18dBm
-
-
0.78
-
V
PDVp16
Output Voltage, POUT =
16dBm
-
-
0.65
-
V
PDVNoRF
Output Voltage, POUT =
No RF
-
-
0.35
-
V
LPF-3dB
Power detect low pass
filter -3dB corner
frequency
-
1500
-
kHz
Load = high impedance
Typ: 500 kΩ
5GHz Power Detector Response
Pdet5090
Pdet4900
Pdet5470
Pdet5850
1
0.9
VDET (V)
0.8
0.7
0.6
0.5
0.4
0.3
0
2
4
6
8
10
12
14
16
18
20
Pout(dBm)
Figure 4: Preliminary SE5502L Power Detector vs. Output Power over Frequency (CW Signal)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
11
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Package Drawing
24
23
22
21
20
19
19
20
21
22
23
24
1
18
18
1
2
17
17
2
3
16
16
3
4
15
15
4
5
14
14
5
6
13
13
6
7
8
9
10
11
12
TOP SIDE
12
11
10
9
8
7
BOTTOM SIDE
Figure 5: Package Drawing: Topside
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
12
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Recommended Land and Solder Patterns
24
23
22
21
20
19
22
21
20
19
1
18
2
17
3
16
16
4
15
15
5
14
14
6
13
13
7
8
9
10
11
12
24
23
22
21
20
19
18
24
23
22
21
20
19
1
18
1
18
2
17
2
17
3
16
3
16
4
15
4
15
5
14
5
14
6
13
6
13
7
8
9
10
11
12
7
8
9
10
11
12
Figure 6: Recommended Land and Solder Patterns
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
13
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Package Handling Information
Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption
may occur when the part is subjected to high temperature during solder assembly. The SE5502L is capable of
withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or
in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that
the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For
details on both attachment techniques, precautions, and handling procedures recommended, please refer to:
 “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045
 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044
Caution! Class 1C ESD sensitive device
Product Branding
Pin 1 Identifier
Terminal Finish
Pin 1
e3
Part
Lot
SiGe
5502L
Lot Code
Figure 7: SE5502L Branding Information
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
14
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Tape and Reel Information
Parameter
Devices Per Reel
Reel Diameter
Tape Width
Value
3000
13 inches
12 millimeters
Figure 8: Detailed Tape and Reel Information (All diminensions in Millimeters)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
15
DATA SHEET
SE5502L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End
Preliminary Information
Document Change History
Revision
Date
Notes
1.0
Aug 25, 2009
Created
1.1
Feb 22, 2010
Updated
1.2
Jul 12, 2010
Updated switch control table and corrected block diagram
1.3
Sep 18, 2010
Updated 2GHz LNA gain variation over band.
Updated 5GHz TX gain min spec
Updated EN high current consumption.
1.4
Oct 7, 2010
Added “Stand By” mode setting to switch control logic table
1.5
Jan 27, 2011
Updated MSL rating to MSL1
Updated ESD rating to Class 1C
1.6
Apr 9, 2011
Updated to Industrial Temperature Range
1.7
Feb 17, 2012
Updated marking diagram
1.8
Apr 03, 2012
Updated with Skyworks logo and disclaimer statement
Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein,
are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or
omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time,
without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other
difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials,
products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in
Skyworks Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE,
INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR
OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT,
INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE
MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to
personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to
fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or
operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks.
Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated
published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries.
Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions,
posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202451A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012
16