Accreditation scope PEHLA

Deutsche Akkreditierungsstelle GmbH
Entrusted according to Section 8 subsection 1 AkkStelleG in connection with Section 1
subsection 1 AkkStelleGBV
Signatory to the Multilateral Agreements of
EA, ILAC and IAF for Mutual Recognition
Ace red itation
The Deutsche Akkreditierungsstelle GmbH attests that the testing laboratory
PEHLA - Gesellschaft für elektrische Hochleistungsprüfungen
Hallenweg 40, 68219 Mannheim
Standort:
PEHLA - Gesellschaft für Elektrische Hochleistungsprüfungen
PEHLA-Prüffeld Berlin-Siemensstadt
Nonnendammal.lee 104, 13629 Berlin
is competent under the terms of DIN EN 150/IEC 17025:2005 to carry out tests in the
following fields:
High-Voltage Switchgear and Controlgear
Power Engineering Equipment
The accreditation certificate shall only apply in connection with the notice of accreditation of 2016-02-26
with the accreditation number D-PL-12072-04 and is valid until 2021-02-25. lt comprises the cover sheet,
the reverse side of the cover sheet and the following annex with a total of 12 pages.
Registration number of the certificate: D-PL-12072-04-00
See notes overleaf.
Deutsche Akkreditierungsstelle GmbH
Office Berlin
Spittelmarkt 10
10117 Berlin
Office Frankfurt am Main
Europa-Allee 52
60327 Frankfurt am Main
Office Braunschweig
Bundesallee 100
38116 Braunschweig
The publication of extracts of the accreditation certificate is subject to the prior written approval by
Deutsche Akkreditierungsstelle GmbH (DAkkS). Exempted is the unchanged form of separate
disseminations of the cover sheet by the conformity assessment body mentioned overleaf.
No impression shall be made that the accreditation also extends to fields beyond the scope of
accreditation attested by DAkkS.
The accreditation was granted pursuant to the Act on the Accreditation Body (AkkStelleG) of 31 July 2009
(Federal Law Gazette 1 p. 2625) and the Regulation (EC) No 765/2008 of the European Parliament and of
the Council of 9 July 2008 setting out the requirements for accreditation and market surveillance relating
to the marketing of products (Official Journal of the European Union L 218 of 9 July 2008, p. 30). DAkkS is
a signatory to the Multilateral Agreements for Mutual Recognition of the European co-operation for
Accreditation (EA), International Accreditation Forum (IAF) and International Laboratory Accreditation
Cooperation (ILAC). The signatories to these agreements recognise each other's accreditations.
The up-to-date state of membership can be retrieved from the following websites:
EA: www.european-accreditation.org
ILAC: www.ilac.org
IAF: www.iaf.nu
Akkred itierungsstelle
Deutsche Akkreditierungsstelle GmbH
Annex to the Accreditation Certificate D-PL-12072-04-00
according to DIN EN 150/IEC 17025:2005
Period of validity:
2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
Holder of certificate:
PEHLA - Gesellschaft für elektrische Hochleistungsprüfungen
Hallenweg 40, 68219 Mannheim
Location:
PEHLA - Gesellschaft für Elektrische Hochleistungsprüfungen
PEHLA-Prüffeld Berlin-Siemensstadt
Nonnendammallee 104, 13629 Berlin
Tests in the fields:
High-Voltage Switchgear and Controlgear
Power Engineering Equipment
The testing laboratory is permitted, without being required to inform and obtain prior approval
from DAkkS, to use standard testing methods listed here with different issue dates.
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Test Range/
Restrictions
General
Electrical
engineering
DIN EN 62271-1:2012
VDE 0671-1:2012
EN 62271-1:2011
IEC 62271-1:2011
High-voltage switchgear and controlgear Part 1: Common specifications
Electrical
engineering
IEEE 4:2013
IEEE Standard Techniques for High-Voltage
Testing
Electrical
engineering
IEEE Std C37.20.2:1999
IEEE Standard for Metal-Clad Switchgear
This document is a translation. The definitive version is the original German annex to the accreditation certificate.
1/12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Electrical
engineering
IEEE Std C37.20.3:2013
IEEE Standard for Metal-Enclosed lnterrupter
Switchgear
Electrical
engineering
IEEE Std C37.100:1992
IEEE Standard Definitions for Power
Switchgear
Electrical
engineering
IEEE Std C37.100.1:2007
Common requirements for high voltage
power switchgear rated above 1000 V
Electrical
engineering
GOST 1516.3-96
Electrical equipment for a.c. voltages from 1
to 750 kV - Requirements for electric strength
of insulation
Test Range/
Restrictions
Circuit-breakers
Electrical
engineering
DIN EN 62271-100:2013
VDE 0671-100:2013
EN 62271-100:2012
IEC 62271-100:2012
STL Guide:2013
High-voltage switchgear and controlgear Part 100: High-voltage alternating-current
circuit-breakers
Electrical
engineering
DIN EN 62271-101:2013
VDE 0671-101:2013
EN 62271-101:2013
IEC 62271-101:2012
STL Guide:2013
High-voltage switchgear and controlgear Part 101: Synthetic testing
Electrical
engineering
DIN EN 62271-108:2006
VDE 0671-108 :2006
EN 62271-108:2006
IEC 62271-108:2005
High-voltage switchgear and controlgear Part 108: High-voltage alternating current
disconnecting circuit-breakers for rated
voltages of 72,5 kV and above
Electrical
engineering
DIN EN 62271-109:2014
VDE 0671-109:2014
EN 62271-109:2013
IEC 62271-109:2013
High-voltage switchgear and controlgear Part 109: Alternating-current series capacitor
by-pass switches
Electrical
engineering
DIN EN 62271-110:2013
VDE 0671-110:2013
EN 62271-110:2012
IEC 62271-110:2012
High-voltage switchgear and controlgear Part 110: lnductive load switching
Electrical
engineering
DIN IEC 62271-111:2014
VDE 0671-111:2014
IEC 62271-111:2012
IEEE Std C37.60:2012
High voltage switchgear and controlgear - Part
111: Overhead, pad-mounted, dry vault, and
submersible automatic circuit reclosers and
fault interrupters for alternating current
systems up to 38 kV
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
2/12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing fie ld
Standard/
ln-House Procedure /
Version
Tit le of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Electrical
engineering
DIN EN 50152-1:2014
VDE 0115-320-1:2014
EN 50152-1:2013
Railway applications - Fixed installations Particular requirements for AC switchgear Part 1: Single-phase circuit-breakers with Un
above 1 kV
Electrical
engineering
DIN EN 50152-2:2013
VDE 0115-320-2:2013
EN 50152-2 :2012
Railway applications - Fixed installations Particular requirements for a.c. switchgear Part 2: Single-phase disconnectors, earthing
switches and switches with Un above 1 kV
Electrical
engineering
DIN EN 60077-1:2003
VDE 0115-460-1:2003
EN 60077-1:2002
IEC 60077-1:1999
Railway applications - Electric equipment for
rolling stock - Part 1: General service
conditions and general rules
Electrical
engineering
DIN EN 60077-2:2003
VDE 0115-460-2:2003
EN 60077-2:2002
IEC 60077-2:1999
Railway applications - Electric equipment for
rolling stock - Part 2: Electrotechnical
components - General rules
Electrical
engineering
DIN EN 60077-4:2004
VDE 0115-460-4:2004
EN 60077-4:2003
IEC 60077-4:2003
Railway applications - Electric equipment for
rolling stock - Part 4: Electrotechnical
components; Rules for AC circuit-breakers
Electrical
engineering
DIN EN 61166:1994
VDE 0670-111:1994
EN 61166:1993
High-voltage alternating current circuitbreakers - Guide for seismic qualification of
high-voltage alternating current circuitbreakers
Electrical
engineering
IEC/TR 62271-300:2006
High-voltage switchgear and controlgear Part 300: Seismic qualification of alternating
current circuit-breakers
Electrical
engineering
IEC/TR 62271-302:2010
Alternating current circuit breakers with
internationally non-simultaneous pole
operation
Electrical
engineering
IEC/TR 62271-310:2008
High-voltage switchgear and controlgear Part 310: Electrical endurance testing for
circuit-breakers of rated voltage 72,5 kV and
above
Electrical
engineering
IEEE Std C37.04:2009
IEEE Std C37.04A:2003
IEEE Std C37 .04B:2008
IEEE Standard Rating Structure for AC HighVoltage Circuit Breakers
Electrical
engineering
IEEE C37.06:2009
AC High-Voltage Circuit Breakers Rated on a
Symmetrical Current Basis - Preferred Ratings
and Related Required Capabilities
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
Test Range/
Restrictions
3/ 12
Akkreditierungsstelle
Annex to the accred itation certificate D-PL-12072-04-00
Testing f ield
St andard /
ln-House Procedure /
Version
Tit le of Standard or ln-House Procedure
(Deviations / M odifications of Standard)
Electrical
engineering
IEEE Std C37 .09:2007
IEEE Std C37.09A:2005
IEEE Std C37 .09B:2010
IEEE Standard Test Procedure for AC HighVoltage Circuit Breakers Rated on a
Symmetrical Current Basis
Electrical
engineering
IEEE Std C37.010:1999
IEEE Application Guide for AC High-Voltage
Circuit Breakers Rated on a Symmetrical
Current Basis
Electrical
engineering
IEEE Std C37.011:2011
IEEE Application Guide for Transient Recovery
Voltage for AC High-Voltage Circuit Breakers
Electrical
engineering
IEEE Std C37.012:2014
IEEE Application Guide for Capacitance
Current Switching for AC High-Voltage Circuit
Breakers
Electrical
engineering
IEEE Std C37.013:1997
IEEE Std C37.013A:2007
IEE E Standard for AC High-Voltage Generator
Circuit Breakers Rated on a Symmetrical
Current Basis
Electrical
engineering
IEEE Std C37.015 :2009
IEEE Application Guide for Shunt Reactor
Switching
Electrical
engineering
IEEE Std C37.016:2006
AC high-voltage circuit switchers rated 15.5
kV through 245 kV
Electrical
engineering
IEEE Std C37.081:1981
IEEE Std C37 .081A:1997
IEEE Guide for Synthetic Fault Test ing of AC
High-Voltage Circuit Breakers Rated on a
Symmetrical Current Basis
Electrical
engineering
IEEE Std C37 .083:1999
IEEE Guide for Synthetic Capacitive Current
Switching Tests of AC High-Voltage Circuit
Breakers
Electrical
engineering
IEEE Std C37 .11:2014
IEEE Standard Requirements for Electrical
Control for AC High-Voltage Circuit Breakers
Rated on a Symmetrical Current Basis
Electrical
engineering
ANSI C37.54:2003
Conformance Test Procedures for lndoor
Alternating Current High-Voltage Circuit
Breakers Applied as Removable Elements in
Metal-Enclosed Switchgear Assemblies
Electrical
engineering
CSA C22.2 No . 31-10 :2010
Switchgear assemblies
Electrical
engineering
GOST 52565-2006
Alternating-Current Circuit-Breakers for
Volt age from 3 to 750 kV
Period of va lidity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
Test Range/
Restrictions
4/12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
{Deviations / Modifications of Standard)
Test Range/
Restrictions
Switches
Electrical
engineering
DIN EN 62271-103:2012
VDE 0671-103:2012
EN 62271-103:2011
IEC 62271-103:2013
STL-Guide:2004
High-voltage switchgear and controlgear Part 103: Switches for rated voltages above 1
kV up to and including 52 kV
Electrical
engineering
DIN EN 62271-104:2010
VDE 0671-104:2010
EN 62271-104:2009
IEC 62271-104:2015
High-voltage switchgear and controlgear Part 104: Alternating current switches for
rated voltages of 52 kV and above
Electrical
engineering
DIN EN 62271-105:2013
VDE 0671-105:2013
EN 62271-105:2012
IEC 62271-105:2012
High-voltage switchgear and controlgear Part 105: Alternating current switch-fuse
combinations
Contactors and motorstarters
Electrical
engineering
DIN IEC 62271-106:2012
VDE 0671-106:2012
EN 62271-106:2011
IEC 62271-106:2011
High-voltage switchgear and controlgear Part 106: Alternating current contactors,
contactor-based controllers and motorstarters
Disconnectors and earthing switches
Electrical
engineering
DIN EN 62271-102:2013
VDE 0671-102:2013
EN 62271-102:2013
IEC 62271-102:2013
STL Guide:2011
High-voltage switchgear and controlgear Part 102: Alternating current disconnectors
and earthing switches
Electrical
engineering
IEEE C37.30.1:2011
IEEE Standard Requirements for High-Voltage
Switches
Electrical
engineering
IEEE C37.41:2008
IEEE Standard Requirements for High-Voltage
Switches
Electrical
engineering
GOST 52726-2007
Diskonnectors and Earthing Switches for AC
Voltage above 1 kV and their Drive Units
Switchgear and controlgear
Electrical
engineering
DIN EN 62271-200:2012
VDE 0671-200:2012
EN 62271-200:2012
IEC 62271-200:2011
STL Guide:2013
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
High-voltage switchgear and controlgear Part 200: AC metal-enclosed switchgear and
controlgear for rated voltages above 1 kV and
up to and including 52 kV
- Translation -
5/12
Akkred itierungsstelle
Annex to the accred itation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Electrical
engineering
DIN EN 62271-201:2015
VDE 0671-201:2015
EN 62271-201:2015
IEC 62271-201:2015
High-voltage switchgear and controlgear Part 201: AC insulation-enclosed switchgear
and controlgear for rated voltages above 1 kV
and up to and including 52 kV
Electrical
engineering
DIN EN 62271-203:2012
VDE 0671-203:2012
EN 62271-203:2012
IEC 62271-203:2013
STL Guide:2013
High-voltage switchgear and controlgear Part 203: Gas-insulated metal-enclosed
switchgear for rated voltages above 52 kV
Electrical
engineering
DIN EN 62271-205:2008
VDE 0671-205:2008
EN 62271-205:2008
IEC 62271-205:2008
High-voltage switchgear and controlgear Part 205: High-voltage switchgear assemblies
for operation at rated voltages above 52 kV
Electrical
engineering
DIN EN 62271-209:2008
VDE 0671-209:2008
EN 62271-209:2007
IEC 62271-209:2007
High-voltage switchgear and controlgear Part 209: Cable connections for gas-insulated
metal-enclosed switchgear for rated voltages
above 52 kV - Fluid-filled and extruded
insulation cables - Fluid-filled and dry-type
cable-terminations
Electrical
engineering
DIN EN 62271-211:2014
VDE 0671-211:2014
EN 62271-211:2014
IEC 62271-211:2014
High-voltage switchgear and controlgear Part 211: Direct connection between power
transformers and gas-insulated metalenclosed switchgear for rated voltages above
52 kV
Electrical
engineering
DIN V 62271-303:2014
VDE V 0671-303:2014
EN 62271-4:2013
IEC 62271-4:2013
High-voltage switchgear and controlgear Part 4: Handling procedures for sulphur
hexafluoride (SF6) and its mixtures
Electrical
engineering
IEEE Std C37.122:2011
IEEE Std C37.122.1:2014
IEEE Standard for Gas-lnsulated Substations
Electrical
engineering
GOST 54828-2011
Gas-insulated metal-enclosed switchgear for
nominal voltages above 110 kV. General
technical specification
Test Range/
Restrictions
Surge arresters
Electrical
engineering
DIN EN 50526-1:2012
VDE 0115-526-1:2012
EN 50526-1:2012
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
Railway applications - Fixed installations D.C.surge arresters and voltage limiting
devices - Part 1: Surge arresters
- Translation -
6/12
Akkred itierungsste ll e
Annex to the accreditation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
(Deviations / M odifications of Standard)
Electrical
engineering
DIN EN 60099-1:2000
VDE 0675-1 :2000
EN 60099-1:1999
Surge arresters; part 1: non-linear resistor
type gapped surge arresters for a.c. systems
Electrical
engineering
DIN EN 60099-4:2010
VDE 0675-4:2010
EN 60099-4:2014
IEC 60099-4:2014
GB11032-2000
Surge arresters - Part 4: Metal-oxide surge
arresters without gaps for a.c. systems
Electrical
engineering
DIN EN 60099-8:2011
VDE 0675-8:2011
EN 60099-8:2011
IEC 60099-8 :2011
Surge arresters - Part 8: Metal-oxide surge
arresters with external series gap (EGLA) for
overhead transmission and distribution lines
of a.c. systems above 1 kV
Electrical
engineering
DIN EN 60099-9:E2013
EN 60099-9:2014
IEC 60099-9 :2014
Surge arresters - Part 9: Metal-oxide surge
arresters without gaps for HVDC converter
stations
Electrical
engineering
DIN EN 61643-11:2013
VDE 0675-6-11:2013
EN 61643-11: 2012
IEC 61643-11:2011
Low-voltage surge protective devices - Part
11: Surge protective devices connected to
low-voltage power distribution systems Requirements and testing methods
Electrical
engineering
IEC 61992-5:2006
Railway applications - Fixed installations - DC
switchgear - Part 5: Surge arresters and lowvoltage limiters for specific use in d.c. systems
Electrical
engineering
IEEE Std C62 .11:2012
IEEE Standard for Metal-Oxide Surge Arresters
for AC Power Circuits (> 1 kV)
Electrical
engineering
CIGRE WG 33/14-05:1989
Application Guide for Metal oxide Arresters
without gaps for HVDC Converter Stations
Electrical
engineering
GOST R 52725-2007
Surge arresters for AC electrical installations
for voltage from 3 kV to 750 kV
Test Range/
Restrictions
Transmission lines
Electrical
engineering
DIN EN 62271-204:2012
VDE 0671-204:2012
EN 62271-204:2011
IEC 62271-204:2011
High-voltage switchgear and controlgear Part 204: Rigid gas-insulated transmission
lines for rated voltage above 52 kV
Electrical
engineering
DIN VDE 0851:1993
VDE 0851:1993
IEC 60353 :2002
Line traps for a.c. power systems
Period of validit y: 2016-02-26 to 2021-02-25
Date of issu e: 2016-02-26
- Translation -
7/ 12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing f ield
Electrical
engineering
Standard/
ln-House Procedure /
Version
DIN EN 60358-1:2013
VDE 0560-2 :2013
EN 60358-1:2012
IEC 60358-1 :2013
Tit le of Standard or ln-House Procedure
{Deviations / Modifications of Standard)
Test Range/
Restrictions
Coupling capacitors and capacitor dividers Part 1: Common clauses
Transformers, Reactors
Electrical
engineering
DIN EN 60076-6:2009
VDE 0532-76-6 :2009
EN 60076-6:2008
IEC 60076-6:2007
Power transformers - Part 6: Reactors
Instrument transformers
Electrical
engineering
DIN EN 61869-1:2010
VDE 0414-9-1:2010
EN 61869-1:2009
IEC 61869-1:2007
STL-Guide:2008
Instrument transformers - Part 1: General
requirements
Electrical
engineering
DIN EN 61869-2:2014
VDE 0414-9-2:2014
EN 61869-2:2012
IEC 61869-2:2012
STL-Guide :1998
Instrument transformers - Part 2: Additional
requirements for current transformers
Electrical
engineering
DIN EN 60044-7:2000
Instrument transformers - Part 7: Electronic
voltage transformers
VDE 0414-44-7:2000
EN 60044-7:2000
IEC 60044-7:1999
Electrical
engineering
DIN EN 60044-8:2003
VDE 0414-44-8:2003
Instrument transformers - Part 8: Electronic
current transformers
EN 60044-8:2002
IEC 60044-8:2002
Electrical
engineering
IEEE Std C57.13:2008
Requirements for instrument transformers
lnsulat ors, Bushings
Electrical
engineering
DIN EN 60383-1:2001
VDE 0446-1 :2001
EN 60383-1:1999
IEC 60383-1:1993
Period of validit y: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
lnsulators for overhead lines with nominal
voltage above 1000 V; part 1: ceramic or glass
insulator units for a.c. systems; definitions,
test methods and acceptance criteria
- Tra nslation -
8/ 12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing fie ld
Standard/
ln-House Procedure /
Version
Tit le of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Electrical
engineering
DIN EN 60383-2:1995
VDE 0446-4:1995
EN 60383-2:1995
IEC 60383-2:1993
lnsulators for overhead lines with a nominal
voltage above 1000 V; part 2: insulator strings
and insulator sets for a.c. systems; definitions,
test methods and acceptance criteria
Electrical
engineering
DIN EN 60137:2009
VDE 0674-5:2009
EN 60137:2008
IEC 60137:2008
lnsulated bushings for alternating voltages
above 1000 V
Electrical
engineering
DIN EN 60168:2001
VDE 0674-1:2001
EN 60168:2000
IEC 60168:2001
Tests on indoor and outdoor post insulators
of ceramic material or glass for systems with
nominal voltages greater than 1000 V
Electrical
engineering
DIN EN 61109:2009
VDE 0441-100:2009
EN 61109:2008
IEC 61109 :2008
lnsulators for overhead lines - Composite
suspension and tension insulators for a.c.
systems with a nominal voltage greater than
1000 V - Definitions, test methods and
acceptance criteria
Electrical
engineering
DIN EN 62155:2004
VDE 0674-200 :2004
EN 62155:2003
IEC 62155:2003
Hollow pressurized and unpressurized
ceramic and glass insulators for use in
electrical equipment with rated voltages
greater than 1000 V
Electrical
engineering
IEC/TS 60815-1:2008
Selection and dimensioning of high-voltage
insulators intended for use in polluted
conditions - Part 1: Definitions, information
and general principles
Electrical
engineering
IEC/TS 60815-2:2008
Selection and dimensioning of high-voltage
insulators intended for use in polluted
conditions - Part 2: Ceramic and glass
insulators for a.c. systems
Electrical
engineering
DIN 48113 :1973
Post insulators for switchgears and substation
with nominal voltages greater than 1000 V;
co-ordination of the definitions for
mechanical bending strength
Electrical
engineering
DIN EN 61462:2008
VDE 0441-102:2008
EN 61462:2007
IEC 61462:2007
Composite hollow insulators - Pressurized and
unpressurized insulators for use in electrical
equipment with rated voltage greater than
1000 V - Definitions, test methods,
acceptance criteria and design
recommendations
Period of validit y: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
Test Range/
Restrictions
9/ 12
Akkreditierungsstelle
Annex to the accred itation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
{Deviations / Modifications of Standard)
Electrical
engineering
ANSI C29.1:1988
Electrical Power lnsulators - Test Methods
Electrical
engineering
ANSI C29.2A:2013
ANSI C29.2B:2013
lnsulators - Wet-Process Porcelain and
Toughened Glass - Suspension Type
Electrical
engineering
ANSI C29.11:2012
Composite lnsulators - Test Methods
Electrical
engineering
ANSI C29.12:2013
lnsulators - Composite-Suspension Type
Test Range/
Restrictions
High-voltage test techniques
Electrical
engineering
DIN IEC 60060-1:2011
VDE 0432-1:2011
EN 60060-1:2010
IEC 60060-1,2010
STL-Guide:2013
High-voltage test techniques; Part 1: General
definitions and test requirements
Electrical
engineering
DIN EN 60060-2:2011
VDE 0432-2:2011
EN 60060-2:2011
IEC 60060-2:2010
STL-Guide:2001
High-voltage test techniques - Part 2:
Measuring systems
Electrical
engineering
DIN EN 60052:2003
VDE 0432-9:2003
EN 60052:2002
IEC 60052:2002
Voltage measurement by means of standard
air gaps
Electrical
engineering
DIN EN 60270:2002
VDE 0434:2002
EN 60270:2001
IEC 60270:2001
High-voltage test techniques - Partial
discharge measurements
Mechanical testings, environment- and guardtesting
Electrical
engineering
DIN EN 60068-2-1:2008
VDE 0468-2-1:2008
EN 60068-2-1:2007
IEC 60068-2-1:2007
Environmental testing - Part 2-1: Tests - Tests
A: Cold
Electrical
engineering
DIN EN 60068-2-2:2008
VDE 0468-2-2:2008
EN 60068-2-2:2007
IEC 60068-2-2:2007
Environmental testing - Part 2-2: Tests - Test
B: Dry heat
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
10/12
Akkreditierungsstelle
Annex to the accred itation certificate D-PL-12072-04-00
Testing field
Standard/
ln-House Procedure /
Version
Title of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Electrical
engineering
DIN EN 60068-2-6:2008
VDE 0468-2-6:2008
EN 60068-2-6:2008
IEC 60068-2-6:2007
Environmental testing - Part 2-6: Tests - Test
Fe: Vibration (sinusoidal)
Electrical
engineering
DIN EN 60068-2-14:2010
VDE 0468-2-14:2010
EN 60068-2-14:2009
IEC 60068-2-14:2009
Environmental testing - Part 2-14: Tests - Test
N: Change of temperature
Electrical
engineering
DIN EN 60068-2-17:1995
EN 60068-2-17:1994
IEC 60068-2-17:1994
Basic environmental testing procedures - Part
2: Tests - Test Q: Sealing
Electrical
engineering
DIN EN 60068-2-27:2010
VDE 0468-2-27:2010
EN 60068-2-27:2009
IEC 60068-2-27:2008
Environmental testing - Part 2-27: Tests - Test
Ea and guidance: Shock
Electrical
engineering
DIN EN 60529:2014
VDE 0470-1:2014
EN 60529:2013
IEC 60529:2013
Degrees of protection provided by enclosures
(IP code)
Eledrical
engineering
IEEE Std 693:2005
IEEE Recommended Practice for Seismic
Design of Substations
Electrical
engineering
DIN EN ISO 3744:2011
ISO 3744:2010
Acoustics - Determination of sound power
levels of noise sources using pressure Engineering method in an essentially free field
over a reflecting plane
Electrical
engineering
DIN 45635-1:1984
Measurement of noise emitted by machines;
airborne noise emission; enveloping surface
method; basic method, divided into 3 grades
of accuracy
Electrical
engineering
DIN 45635-12:1978
Measurement of noise emitted by machines;
Airborne noise measurement, enveloping
surface method; Electrical switchgear and
control gear
Electrical
engineering
DIN EN ISO 11201:2010
EN ISO 11201:2010
ISO 11201:2010
Acoustics - Noise emitted by machinery and
equipment - Measurement of emission sound
pressure levels at a work station and at other
specified positions - Engineering method in an
essentially free field over a reflecting plane
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
- Translation -
Test Range/
Restrictions
11/12
Akkreditierungsstelle
Annex to the accreditation certificate D-PL-12072-04-00
Testing field
Electrical
engineering
Standard/
ln-House Procedure /
Version
DIN EN ISO 11202:2010
EN ISO 11202:2010
ISO 11202:2010
Period of validity: 2016-02-26 to 2021-02-25
Date of issue: 2016-02-26
Title of Standard or ln-House Procedure
(Deviations / Modifications of Standard)
Test Range/
Restrictions
Acoustics - Noise emitted by machinery and
equipment - Determination of emission sound
pressure levels at a work station and at other
specified positions applying approximate
environmental corrections
- Translation -
12/1 2