PM25A Series MEDICAL 2 5 - 2 8 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T FEATURES • Low safety ground leakage current • Wide input range 85 to 264Vac • Input surge current protection • Overvoltage protection • Overcurrent protection • Open PCB construction • 100% burn-in at full rated load SPECIFICATIONS INPUT OPERATING Input voltage 85–264Vac MTBF 500,000 hrs @ 25°C Frequency Input current 47Hz–63Hz 0.7A (rms) for 115Vac. 0.4A (rms) for 230Vac. 90µA max. @ 115Vac. 60Hz. 150µA max. @ 230Vac. 50Hz. Efficiency 68%–70% Input – Output: 4000VAC Input – Ground: 1500VAC Output – Ground: 500VAC Leakage current Isolation Inrush current 10A @ 115V, 25A @ 230V @ 25°C cold start OUTPUT Output voltage See table. Output voltage adjustment V1 only ±10%. Output current See table. Ripple & noise 1% peak to peak max. Line regulation ±0.5% maximum at full load. Load regulation Transient response Temperature coefficient See table. Max. deviation 4% recovering to 1% within 500µs after 25% load charge Provided on V1 only. Set at 110%–132% of nominal All outputs protected for short circuit conditions All outputs ±0.04% per °C Holdup time Typically 10ms at 110VAC Overvoltage protection Overcurrent protection Doc. No. PBC9 Rev.C 28-4-11 ENVIRONMENTAL Operating temperature 0°C to 70°C Derating Derate to 50% at 70°C Storage temperature -40°C to 85°C Relative humidity 5%–95% non-condensing STANDARDS AND APPROVALS Safety standards UL2601-1, CSA C22.2, TUV EN60601-1 C-Tick AS/NZS CISPR11 Group 1, Class A EMC standards EN60601-1-2: 2001 EN61000-4-2, EN610004-3,EN61000-4-4, EN61000-4-5, EN61000-46,EN61000-4-8, EN61000-4-11 EMI standards EN55011 Class B, FCC Class B, VCCI Class B MECHANICAL Dimensions Weight Powering Progress – www.powerbox.com.au 107.95x63.5x24.38mm Single output model: 163grams. Multi-output model: 175 grams. 389 MEDICAL PM25A Series 2 5 - 2 8 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T SELECTION TABLE MAX. MODEL OUTPUT #1 OUTPUT #2 VNOM OUTPUT #3 IMIN IMAX TOL VNOM IMIN IMAX OUTPUT NUMBER VNOM IMIN IMAX TOL PM25-10A 5.1V 0A 5.5A 2% TOL POWER 28W PM25-12A 12V 0A 2.3A 1% 28W PM25-13A 15V 0A 1.9A 1% 28W PM25-14A 24V 0A 1.2A 1% 28W PM25-15A 28V 0A 1.0A 1% PM25-23A +5.1V 0A 2.5A 3% +12V 0.2A 1.5A 5% PM25-25A +5.1V 0A 2.5A 3% +24V 0.1A 0.8A 5% PM25-31A +5.1V 0A 2.5A 3% +12V 0.2A 1.5A 5% -12V 0.05A 0.2A 4% 25W PM25-32A +5.1V 0A 2.5A 3% +15V 0.1A 1.0A 5% -15V 0.05A 0.2A 4% 25W PM25-39A +5.1V 0.3A 2.5A 3% +24V 0.1A 0.8A 5% -12V 0.05A 0.2A 4% 25W 28W 25W 25W NOTES: 1. Safety agency approvals are for the above listed models in PCB form. To order a model with a metallic L-bracket or box, change suffix “A” to “B” for L-bracket form, to “C” for enclosed form, e.g. PM25-31C. 2. All models may be operated at no-load without damage. At no-load, output voltage tolerance increases to ±10%. 3. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and PIN CHART SINGLE OUTPUT MODELS MODEL PIN 1 2 3 4 PM25-10A PM25-13A PM25-15A PM25-12A PM25-14A Return Return Output 1 Output 1 Output 2 Output 2 Output 1 Output 1 Output 1 Output 1 5 6 MULTIPLE OUTPUT MODELS PM25-23A PM25-31A PM25-39A PM25-25A PM25-32A Common Return Common Return Common Return Common Return N.C. Output 3 MECHANICAL SPECIFICATIONS SINGLE OUTPUT 390 MULTIPLE OUTPUT Doc. No. PBC9 Rev.C 28-4-11