LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.6W Power Light LED Pb Lead-Free Parts LG-5630WKZ-DT-1-WW-D01 DATA SHEET DOC. NO : QW0905-LG-5630WKZ-DT-1-WW-D01 REV. : A DATE : 11 - Feb. - 2011 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK Z - D T - 1 - WW - X X1 X2 X1 Title X3 X2 Dimension(L) LG:Ligitek X7 Package T:Tape&Reel 57:5.7mm 56:5.6mm X4 X5 X6 X7 X8 X3 X4 Dimension(W) Emitting Color 30:3.0mm X8 WK:White Color X9 Chip Modification Chromaticity Coordinates -X: 2 chip in 1(Parallel) -1: 1 chip in 1 -2: 2 chip in 1(Series) -CW: Cool White -NW: Neutral White -WW: Warm White Page 1/15 X9 X10 X5 X6 Zener Epoxy Color D:Yellow Diffused X10 Bin Modification LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *. Reading Light (car,bus,aircraft) *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 C 3.0 A C Recommended Solder Patterns 5.6 2.0 0.9 1.6 1.62 3.8 6.8 0.5 0.8 1.28 0.5 2.1 Slug Anode(+) 0.3 2.3 0.8 Cathode(-) Note: 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.The slug has polarity as anode. 3.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol UNIT Warm White DC Forward Current IF 150 mA Power Dissipation PD 0.6 W Peak pulse current Duty 1/10@10KHz IFP 200 mA LED junction Temperature Tj 125 ℃ Reverse Current(VR=5V) Ir 10 μA ESD Sensitivity VB ±2000 V Storage Temperature Tstg -40 ~ +100 °C Operating Temperature Topr -40 ~ +85 °C Soldering Temperature Tp 260 °C Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Luminous Intensity Characteristics at 150mA (Ratings At 25°C Ambient) Luminous Intensity PART NO Emission Color Min. Typ. Max. LG-5630WKZ-DT-1-WW-D01 Warm White 33 35 ---- Note : 1. Warm White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Page 3/15 Units lm LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage Characteristics at 150mA (Ratings At 25°C Ambient) PART NO Emission Color LG-5630WKZ-DT-1-WW-D01 Warm White Vf Min. Typ. Max. ---- 3.3 3.8 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 150mA (Ratings At 25℃ Ambient ) PART NO Emission Color LG-5630WKZ-DT-1-WW-D01 Warm White Chromaticity Coordinates (TYP.) X Y 0.46 0.41 Note : ±0.01 is tester tolerance. Emission Angle Characteristics at 150mA (Ratings At 25°C Ambient ) PART NO Emission Color LG-5630WKZ-DT-1-WW-D01 Warm White Lambertian Units 120 Degrees Color Rendering Index Characteristics at 150mA (Ratings At 25°C Ambient ) PART NO Emission Color LG-5630WKZ-DT-1-WW-D01 Warm White CRI Min. Typ. Max. 80 ---- ---- Page 4/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity F36T Luminous Intensity (lm) @IF=150mA Bin Code Min. Max. F33T 33 36 F36T 36 39 CIE Forward Voltage MO 3.0-3.2 Color Rank @IF=150mA Forward Voltage(V) @IF=150mA LM-NP 2.8-3.0 3.0-3.2 3.2-3.4 3.4-3.6 3.6-3.8 Page 5/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of chromaticity coordinates Color Coordiante at 150mA CCT(K) 2520~2670 2670~2850 2850~3050 BIN CODE 1 2 X Y X 3 Y X 4 Y X Y LM 0.477 0.437 0.4930 0.4410 0.5030 0.4570 0.4870 0.4540 LN 0.467 0.420 0.4830 0.4240 0.4930 0.4410 0.4770 0.4370 LO 0.458 0.403 0.4740 0.4070 0.4830 0.4240 0.4670 0.4200 LP 0.449 0.3880 0.4650 0.3920 0.4740 0.4070 0.4580 0.4030 MM 0.471 0.451 0.461 0.433 0.477 0.437 0.487 0.454 MN 0.461 0.433 0.453 0.416 0.467 0.420 0.477 0.437 MO 0.453 0.416 0.444 0.399 0.458 0.403 0.467 0.416 MP 0.458 0.403 0.444 0.399 0.436 0.384 0.449 0.338 NM 0.454 0.446 0.471 0.451 0.46 0.43 0.444 0.426 NN 0.444 0.426 0.46 0.43 0.453 0.416 0.438 0.412 NO 0.438 0.412 0.453 0.416 0.444 0.399 0.429 0.394 NP 0.429 0.394 0.444 0.399 0.436 0.384 0.422 0.379 NOTE: Tolerance on each color bin(x,y)is±0.01 Page 6/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only The C.I.E 1931 Chromaticity Coordinates 0.48 2670K 2520K 3050K 2850K 0.46 NM MM 0.44 NN 0.42 NO 0.40 LM MN LN MO LO NP MP LP 0.38 0.36 0.36 0.38 0.40 0.42 0.44 0.46 Page 7/15 0.48 0.50 0.52 0.54 0.56 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 8/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.1 Forward current vs. Forward Voltage Forward Current(mA) 160 120 80 40 0 2.0 2.5 3.0 3.5 4.0 4.5 Forward Voltage(V) Fig.3 Forward current vs.Luminous Intensity Relative Luminous Intensity(%) 1.2 1.0 0.8 0.6 0.4 0.2 0 30 60 Page 9/15 90 120 150 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Relative Luminous Flux(%) Fig.5 Luminous Spectrum(Ta=25 ℃) SPECTRAL RADIANCE 80 60 40 20 0 500 400 600 700 800 Wavelength (nm) Fig.6 Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 Page 10/15 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.95 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ± 0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 11/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LG-5630WKZ-DT-1-WW-D01 LOT : GS1-060109 QTY(PCS): 2000 BIN/HUE : F36T/MO BIN : Luminous Flux HUE : Chromaticity Coordinates (CIE_x , CIE_y) VF:3.0-3.2 3.0 - 3.2 : Forward Voltage Reel Dimensions 16.0 ±1.0 60.2±0.5 Page 12/15 178±1 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 13/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test (1)Test items and results Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=150mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=100 ℃ 2.t=1000 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.Ta= 85℃ 2.RH=85 % 3.t=1000 hrs 22 Endurance Test Thermal Shock Test Environmental Test Reflow Soldering Test Temperature Cycling 1.Ta=-40 ℃(30min) -100 ℃(30min) 2.total 100 cycles 22 1.T.Sol=260 ℃±5℃ 2.Dwell Time= 10 Sec.Max. 22 1.100 ℃ ~ 25℃ ~ - 40℃ 30mins 5mins 30mins 2.100 Cyeles 22 (2)Criteria for judging the damage Item Symbol Test Conditions Criteria for Judgement Min. Max. Forward Voltage Vf If=150mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=150mA L.S.L x 0.5 - Note: 1.U.S.L.:Upper Standard Level. 2.L.S.L.:Lower Standard Level. Page 14/15 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35 ℃,RH60%, they should be treated at 60 ℃±5 ℃for 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 15/15