LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only 0.2W Power Light LED Pb Lead-Free Parts LG-5630WK-DT-1-T60-XX-XXX DATA SHEET DOC. NO : QW0905-LG-5630WK-DT-1-T60-XX-XXX REV. : B DATE : 12 - Jul. - 2012 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product Model Designation System LG - 56 30 WK Z - D T - 1 - T60 - P - CW - D01 A B A Title LG:Ligitek F Epoxy Color D:Yellow Diffused C D E B Dimension(L) 57:5.7mm 56:5.6mm G Package T:Tape&Reel F G H C D Emitting Color 30:3.0mm WK:White Color H I Chip Modification Test Current -X: 2 chip in 1(Parallel) T60: 60mA -2: 2 chip in 1(Series) K J Dimension(W) -1: 1 chip in 1 Chromaticity Coordinates I L Bin Modification -CW: Cool White -NW: Neutral White -WW: Warm White Page 1/17 K L E Zener J Patent P: IP Free LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Typical Applications Features *. White colored SMTpackage *.Suitable for all SMT assembly and soldering methodes *. Pb-Free Reflow soldering application *. More Energy Efficient than lncandescent and most Halogen lamps. *. RoHS compliant *. Reading Light (car,bus,aircraft) *. Portable(flashlight,bicycle). *. Backlights(Monitor,TV) / Light Guides. *. Automotive Exterior (Stop-Tail-Tum,CHMSL,Mirror Side Repeat). *. Commercial and Residential Architectural lighting. *. Mini-accent / Uplighters / Downlighters / Orientation lighting *. Fiber Optic Alternative / Decorative / Entertainment lighting. *. Security / Garden lighting. *. Cove / Undershelf / Task lighting. *. Traffic signaling / Beacons / Rail crossing and Wayside lighting. Dimension 5.3 3.0 C A C Recommended Solder Patterns 5.6 2.0 0.9 1.62 0.5 0.8 1.28 1.6 0.8 3.8 6.8 0.5 2.1 Slug Anode(+) 0.3 2.3 Cathode(-) Note: 1.The tolerance unless mentioned is ±0.1mm,unit=mm. 2.It is strongly recommended to apply on electrically isolated heat conducting film between the slug and contact surfaces. Page 2/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol UNIT White DC Forward Current IF 60 mA Power Dissipation PD 0.22 W Peak pulse current Duty 1/10@10KHz IFP 100 mA LED junction Temperature Tj 125 ℃ Reverse Current(VR=5V) Ir 10 μA ESD Sensitivity VB ±500 V Storage Temperature Tstg -40 ~ +100 °C Operating Temperature Topr -40 ~ +85 °C Soldering Temperature Tp 260 °C Note: 1.Proper current derating must be observed to maintain temperature below the maximum. 2.LEDS are not designed to be driven in reverse bias. Device Selection Guide: Part No. MATERIAL COLOR Emitted Lens Cool White LG-5630WK-DT-1-T60-XX-XXX InGaN/GaN Neutral White Warm White Page 3/17 Yellow Diffused LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Luminous Intensity Characteristics at 60mA (Ratings At 25°C Ambient) Luminous Intensity Part No. Emission Color Min. Typ. Max. LG-5630WK-DT-1-T60-XX-XXX White 16 ---- 30 Units lm Note : 1. White emitters are built with InGaN. 2. Luminous Intensity is measured with an accuracy of ±10% Forward Voltage Characteristics at 60mA (Ratings At 25°C Ambient) Vf Part No. Emission Color Min. Typ. Max. LG-5630WK-DT-1-T60-XX-XXX White 2.8 ---- 3.6 Units V Note : Forward Voltage is measured with an accuracy of±0.1V Chromaticity Coordinates Characteristics at 60mA (Ratings At 25°C Ambient ) Part No. Emission Color LG-5630WK-DT-1-T60-XX-XXX White Chromaticity Coordinates X Y Min. Max. Min. Max. 0.3053 0.467 0.3106 0.416 Note : Chromaticity Coordinates is measured with an accuracy of±0.01. Emission Angle Characteristics at 60mA (Ratings At 25°C Ambient ) Part No. Emission Color Lambertian Units LG-5630WK-DT-1-T60-X-XX-XXX White 120 Degrees Page 4/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Product List Part No. CCT(K) CRI Luminous Intensity(lm) Min. Max. Min. Min. Typ. Max. LG-5630WK-DT-1-T60-CW-D01 5650 7000 70 18 20 30 LG-5630WK-DT-1-T60-CW-D02 5000 6300 70 18 20.5 30 LG-5630WK-DT-1-T60-NW-D01 3800 4500 70 18 20 30 LG-5630WK-DT-1-T60-WW-D01 2850 3250 70 16 18 28 LG-5630WK-DT-1-T60-WW-D02 2670 3050 70 16 18 28 Note : CRI is measured with an accuracy of±2.0. Page 5/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bin Code Description Bin Code Luminous Intensity CIE Forward Voltage F20D WO 3.0-3.1 Luminous Intensity (lm) @IF=60mA Bin Code Min. Max. F14D 14 16 F16D 16 18 F18D 18 20 F20D 20 22 F22D 22 24 F24D 24 26 F26D 26 28 F28D 28 30 Color Rank @IF=60mA Forward Voltage(V) @IF=60mA CW NW WW VN SN MN 2.8-2.9 VO SO MO 2.9-3.0 WN TN NN 3.0-3.1 WO TO NO 3.1-3.2 XN PN 3.2-3.3 XO PO 3.3-3.4 3.4-3.5 3.5-3.6 Page 6/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of CW chromaticity coordinates Color Coordiante at 60mA CCT(K) 5000~5650 5650~6300 6300~7000 BIN CODE 1 3 2 4 X Y X Y X Y X Y VN 0.329 0.357 0.347 0.372 0.346 0.359 0.329 0.345 VO 0.329 0.345 0.346 0.359 0.344 0.344 0.329 0.331 WN 0.315 0.344 0.329 0.357 0.329 0.345 0.316 0.333 WO 0.316 0.333 0.329 0.345 0.329 0.331 0.317 0.32 XN 0.3032 0.3332 0.315 0.344 0.316 0.333 0.3053 0.3222 XO 0.3053 0.3222 0.316 0.333 0.317 0.32 0.3076 0.3106 0.40 0.38 5000K 5650K 0.36 6300K 0.34 7000K 0.32 XN XO WN WO VN VO 0.30 0.28 0.26 0.28 0.30 0.32 Page 7/17 0.34 0.36 0.38 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of NW chromaticity coordinates Color Coordiante at 60mA CCT(K) 3800~4100 4100~4500 BIN CODE 1 X 3 2 Y X Y X 4 Y X Y SN 0.3776 0.3963 0.397 0.406 0.392 0.391 0.3744 0.3819 SO 0.3744 0.3819 0.392 0.391 0.387 0.374 0.3708 0.3657 TN 0.361 0.3845 0.3776 0.3963 0.3744 0.3819 0.3586 0.3702 TO 0.3586 0.3702 0.3744 0.3819 0.3708 0.3657 0.3559 0.3547 0.44 3800K 0.42 4100K 4500K 0.40 SN TN 0.38 SO TO 0.36 0.34 0.32 0.30 0.32 0.34 0.36 Page 8/17 0.38 0.40 0.42 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Bins Code of WW chromaticity coordinates Color Coordiante at 60mA CCT(K) 2670~2850 BIN CODE 1 3 2 4 X Y X Y X Y X Y MN 0.461 0.433 0.453 0.416 0.467 0.420 0.477 0.437 MO 0.453 0.416 0.444 0.399 0.458 0.403 0.467 0.416 NN 0.444 0.426 0.46 0.43 0.453 0.416 0.438 0.412 NO 0.438 0.412 0.453 0.416 0.444 0.399 0.429 0.394 PN 0.43 0.421 0.444 0.426 0.438 0.412 0.424 0.407 PO 0.424 0.407 0.438 0.412 0.429 0.394 0.416 0.389 2850~3050 3050~3250 0.47 2850K 3050K 0.45 2670K 3250K 0.43 PN NN 0.41 PO NO MN MO 0.39 0.37 0.35 0.36 0.38 0.40 0.42 0.44 0.46 Page 9/17 0.48 0.50 0.52 0.54 0.56 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Recommended Profile for Reflow Soldering Pb -free solder temperature profile Pb -free solder Temperature profile Pre-heat Pre-heat time Peak-Temperature Soldering time condition 180-200°C 120 Sec Max 260°C Max 10 Sec Max 260°C.Max. 10 Sec .Max. 1-5°C/Sec. 60 Sec.Max. Above220°C 6°C/Sec. Pre-heating 180-200°C 1-5°C/Sec. 120 Sec. Max. (1) Reflow soldering should not be done more than two times. (2) When soldering,do not put stress on the LEDs during heating. (3) After soldering,do not warp the circuit board. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter,the picking up nozzle that does not affect the silicone resin should be used. Hand Soldering Conditions: Do not exceed 3 seconds at maximum 320°C under soldering iron.(one time only) Page 10/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Forward Voltage(V) Fig.1 Forward current vs. Forward Voltage Forward Current(mA) Relative Luminous Intensity(%) Fig.2 Forward current vs.Luminous Intensity Forward Current(mA) Page 11/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Fig.3 Luminous Spectrum(Ta=25 °C) Relative Luminous Flux(%) SPECTRAL RADIANCE Wavelength (nm) Fig.4 Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 Page 12/17 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Carrier Type Dimensions 4.0 0.25 1.5 1.75 - 5.5 + 12.0±0.3 5.95 9.3 Polarity 4.0 3.25 1.2 Note : The tolerances unless mentioned is ±0.2mm. Packing Specifications Label Aluminum Moist-Proof bag Label Desiccant Page 13/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Label Explanation Pb LIGITEK ELECTRONICS CO., LTD. PART : LG-5630WK-DT-1-T60-CW-D02 LOT : GS1-060109 QTY(PCS): 2000 BIN/HUE : F20D/VO BIN : Luminous Flux HUE : Chromaticity Coordinates (CIE_x , CIE_y) VF:3.1-3.2 3.1 - 3.2 : Forward Voltage Reel Dimensions 16.0±1.0 60.2±0.5 178±1 13.5 Page 14/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm W L H Page 15/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Reliability Test: (1)Test items and results Classification Test Item Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=60mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=105 ℃± 5℃ 2.t=500 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta= 85℃± 5℃ 3.RH=90 %~95% 4.t=500 hrs±2hrs 22 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃ ±5℃ & -40 ℃± 5℃ ( 30min) (30min) 3.total 100 cycles 22 1.T.Sol=260 ℃±5℃ 2.Dwell Time= 10 Max. 22 1.105 ℃ ~ 25℃ ~ - 40℃ 30mins 15mins 30mins 2.10 0 Cyeles 22 Endurance Test Thermal Shock Test Environmental Test Reflow Soldering Test Temperature Cycling (2)Criteria for judging the damage Item Symbol Test Conditions Criteria for Judgement Min. Max. Forward Voltage Vf If=60mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=60mA L.S.L x 0.7 - Page 16/17 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃for 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forward current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Page 17/17