LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL Pb Lead-Free Parts LDUV9553-A01 DATA SHEET DOC. NO : QW0905-LDUV9553-A01 REV. : A DATE : 31 - Jul. - 2012 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/11 PART NO.LDUV9553-A01 Features: 1. Top view LED. 2. white SMT package. 3. Leadframe package with individual 2 pin. 4.Wide viewing angle. 5.Soldering methods:IR reflow soldering. 6.Feature of the device:more light due to higher optical efficiency;extremely wide viewing angle;ideal for backlighting and coupling in light guide. Descriptions: The LDUV9553 SMD has wide viewing angle and optimized light coupling by inter reflector,The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium. Applications: 1. Telecommunication: indicator and backlighting in telephone and fax. 2. Indicators. 3. Switch lights. Device Selection Guide: PART NO MATERIAL LDUV9553-A01 InGaN COLOR Emitted Lens PURPLE Water Clear LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/11 PART NO.LDUV9553-A01 Package Dimensions 3.5 1.85 0.9 0.9 2.8 2.2 Cathode Mark Soldering Terminal 3.2 Andoe 0.9 Cathode Polarity 0.9 Note : 1.All dimension are in millimeter tolerance is ±0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Recommended Soldering Pad Dimensions 4.5 1.5 1.5 2.6 Note : The tolerances unless mentioned is ±0.1mm,Angle ±0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/11 PART NO.LDUV9553-A01 Absolute Maximum Ratings at Ta=25℃ Ratings Parameter Symbol UNIT DUV Forward Current IF 30 mA Peak Forward Current Duty 1/11@10KHz IFP 100 mA Power Dissipation PD 120 mW Reverse Current @5V Ir 50 μA Electrostatic Discharge ESD 500 V Operating Temperature Topr - 20 ~ + 80 ℃ Storage Temperature Tstg - 30 ~ + 100 ℃ Typical Electrical & Optical Characteristics (Ta=25℃) Symbol Min. Typ. Radiant Intensity Po 1.8 2.8 ---- mw/sr IF=20mA Peak Wavelength λP 410 ---- 420 nm IF=20mA △λ ---- 20 ---- nm IF=20mA VF ---- 3.5 4.0 V IF=20mA 2θ 1/2 ---- 120 ---- deg IF=20mA Items Spectral Line Half-Width Forward Voltage Viewing Angle Max. UNIT Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2.The luminous intensity data did not including ±15% testing tolerance. 3.The peak wavelength data did not including ±1nm testing tolerance. CONDITION LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/11 PART NO.LDUV9553-A01 Luminous Intensity Classification BIN CODE M N P Q R Po(mw/sr) at20mA Min. Max. 1.8 2.4 3.2 4.2 5.5 2.4 3.2 4.2 5.5 7.2 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/11 PART NO.LDUV9553-A01 Typical Electro-Optical Characteristics Curve DUV CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vsForward Current 3.9 2.5 3.8 2.0 Relative Intensity Normalize @20mA Forward Voltage(V) 3.7 3.6 3.5 3.4 3.3 3.2 1.5 1.0 0.5 0 3.1 20 30 40 50 60 70 80 90 100 20 30 40 50 60 70 80 90 100 Forward Current(mA) Forward Current(mA) Fig.4 Relative Intensity vs. Wavelength Fig.3 Forward Current vs. Wavelength 1.0 Relative Intensity@20mA Wavelength(nm)WLP 420 410 400 390 380 20 40 80 60 100 0.5 0.0 350 400 450 Wavelength (nm) Fig.5 Directive Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% 550 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/11 PART NO.LDUV9553-A01 Carrier Type Dimensions 4.0 2.0 4.0 2.24 ψ1.55 1.75 5.5 12.0±0.3 9.3 4.06 Polarity 3.12 Note : The tolerances unless mentioned is ±0.1mm,Unit=mm. ‧ Packing Specifications 0.2 0.8 0.6 Aluminum Moist-Proof bag Label 0.8 0.6 0.2 0.4 0.4 Label Part No. Description Quantity/Reel LDUV9553-A01 12.0mm tape,7"reel 1500 PCS LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/11 PART NO.LDUV9553-A01 Label Explanation LIGITEK ELECTRONICS CO., LTD. Pb PART : LDUV9553-A01 LOT : GS1-090168 QTY(PCS): 1500 BIN/HUE : N BIN : Radiant Intensity VF:2.8-3.6 2.8 - 3.6 : Forward Voltage Reel Dimensions 0.2 0.4 0.8 0.8 0.6 0.2 0.4 0.6 2.0±0.5 ψ13.5±1.0 178±1.5 60.0±1.0 13.0±1.0 16.0±1.0 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 8/11 PART NO.LDUV9553-A01 Box Explanation 1. 4 BAG / INNER BOX 2. INNER BOX SIZE : L X W X H 23cm X 8.5cm x 26cm H W L 3. 10 INNER BOXES / CARTON 4. CARTON SIZE : L X W X H 58cm X 34cm x 35cm L W H LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 9/11 PART NO.LDUV9553-A01 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 320℃ 3 sec one time only. 2. Wave Solder Soldering heat Max. 260 ℃ 245±5℃ within 5 sec 120 ~ 150℃ Preheat 120 ~ 180 sec 3 PB-Free Reflow Solder 1~5°C/sec 1~5°C/sec Preheat 180~200°C 260°C MaX. 10sec.Max 6°C/sec Above 220°C 60 sec.Max. 120 sec.Max. Note: 1.Reflow soldering should not be done more than two times. 2.When soldering,do not put stress on the LEDs during heating. 3.After soldering,do not warp the circuit board. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 10/11 PART NO.LDUV9553-A01 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃±5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40% of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 11/11 PART NO.LDUV9553-A01 Reliability Test: (1)Test items and results Test Item Classification Test Condition Sample Size Operating Life Test 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs 22 High Temperature Storage Test 1.Ta=105 ℃± 5℃ 2.t=500 hrs 22 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs 22 High Temperature High Humidity Storage Test 1.IR-Reflow In-Board, 2 Times 2.Ta=85℃± 5℃ 3.RH=90 %~95% 4.t=500hrs±2hrs 22 Thermal Shock Test 1.IR-Reflow In-Board,2 times 2.Ta=105 ℃ ±5℃ & -40℃± 5℃ (30min) (30min) 3.total 100 cycles 22 1.T.Sol=260 ℃±5℃ 2.Dwell Time= 10Max. 22 1.105℃ ~ 25℃ ~ - 40℃ 30mins 15mins 30mins 2.100 Cyeles 22 Endurance Test Environmental Test Reflow Soldering Test Temperature Cycling (2)Criteria for judging the damage Item Symbol Test Conditions Criteria for Judgement Min. Max. Forward Voltage Vf If=20mA - U.S.L x1.2 Reverse Current Ir Vr=5V - U.S.L x2.0 Luminous Intensity Iv If=20mA L.S.L x 0.5 - Note: 1.U.S.L.:Upper Standard Level. 2.L.S.L.:Lower Standard Level.