AN60305 Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC.pdf

Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Author: Chris Keeser
Associated Project: No
Associated Part Family: CY8C3xxx, CY8C5xxx
Related Application Notes: None
If you have a question, or need help with this application note, visit
More code examples? We heard you.
To access an ever-growing list of hundreds of PSoC code examples, please visit our code examples web page.
You can also explore the PSoC 4 video library here.
This application note describes how to configure the PSoC 3 and PSoC 5LP IDACs as a flexible analog source. It
presents different approaches for using the IDACs in applications, and discusses the advantages and disadvantages of
the topologies presented. This application note will: help you to understand compliance voltage and why it is important;
explain how to generate an “any range” or “any ground” VDAC; describe an implementation for a multiplying VDAC; give
details on how to build a rail-to-rail low-output impedance 9-bit VDAC from a single IDAC, an opamp, and a resistor; and
provide information on how to build a current scaling circuit with an opamp and two resistors.
Voltage DACs Are Great, Current DACs Are Great; PSoC 3 and PSoC 5LP Have Both
Generating an analog signal from digital systems is often a vital part of system design. The generated analog signal
can be used to control any number of aspects in a system. Digital-to-analog converter (DAC) requirements are as
varied as the applications of which they are a part. Voltage DACs (VDACs) can be used to bias field effect transistors,
provide sensor excitation signals, apply a known calibration voltage, generate waveforms, and control voltage
operated circuits. Current DACs (IDACs) can be used to bias transistors, perform open circuit detection on long
sensor loops, level shift signals, provide precise continuous LED brightness control, and charge or discharge
capacitors in a controlled manner (super capacitors), to name a few applications.
Having an IDAC or VDAC provides great flexibility in your designs, but having both makes it possible to address
specific design requirements with minimum extra hardware.
Know the Limitations of your IDAC
Let us say for your specific design you need a voltage output range of 0 to 200 mV. PSoC 3 and PSoC 5LP VDACs
have two built-in ranges of 0 to 1.020 V and 0 to 4.080 V. Neither range is ideal because you want to have the full
resolution over your 200 mV range. What do you do? Use an IDAC.
An IDAC and a resistor can generate any desired voltage range as long as you do not violate the compliance voltage
of the IDAC. The compliance voltage describes the maximum/minimum voltage a practical current source can reach
when attempting to source current and the minimum voltage it can reach when attempting to sink current.
In an ideal current source, the voltage at the output can vary from negative infinity to positive infinity ensuring the
specified current flows through the load. This is difficult to achieve in reality, so there are limits on what can be
accomplished. Figure 1 shows a simple current source. The voltage at the transistor’s base is kept one diode drop
below the voltage at the emitter. The current flowing out of the base is kept at a fixed 10 µA because the base voltage
is fixed. The transistors beta (current gain) amplifies the base current by a factor of 100, producing 1 mA at the
collector, ignoring the negligible base current contribution.
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
The circuit shown in Figure 1 tries to source 1 mA from the collector into a load connected to the output, but there are
limitations. Let us say that the voltage from the emitter to the collector must be greater than or equal to 0.7 V to
maintain the current through the transistor. All other non-idealities of real transistors are ignored. As long as the load
does not require more than 5 volts on the collector to consume 1 mA, this circuit will act as a current source. The
collector voltage can move “up and down” as needed to source 1 mA. The compliance voltage of this current source
is 0.7 V. If the load requires greater than 5 volts to consume 1 mA, (5.7 minus the compliance voltage of 0.7) the
current source cannot provide 1 mA.
The compliance voltage for the PSoC 3 and PSoC 5LP devices are available in the device datasheet.
Figure 1. Simple Current Source
“Any Range” VDAC from IDAC and Resistor
To generate the 0 to 200 mV range with an IDAC, implement the circuit shown in Figure 2.
Figure 2. Simple VDAC from IDAC
The resistor is selected based on the maximum output voltage desired and the maximum current that can be sourced
by the IDAC in its selected mode (see Equation 1). For example, if the 32 µA range is selected, you need a 200
mV/32 µA = 6.25 kΩ resistor.
Equation 1
If you do not want your desired voltage to be affected by the load connected, make your drive circuit’s output
impedance very low compared to the input impedance of the load. How low the output impedance needs to be is up
to you, the circuit designer.
The Norton and Thevenin equivalent circuits are useful tools to determine the output impedance of a circuit. Using an
IDAC as a VDAC lends itself well to analysis as a Norton circuit.
You can change the Norton equivalent circuit (current source in parallel with a resistor) into a Thevenin equivalent
circuit (voltage source in series with a resistor) using the conversion in Figure 3. This allows to easily see the effective
output impedance of the circuit.
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Figure 3. Norton to Thevenin Conversion
This means that the “VDAC” has an equivalent output impedance of 6.25 kΩ. In some cases, this output impedance
may be too high. If you increase the IDAC output range from 32 µA to 2.040 mA, the same 0 to 200 mV range will
require a 98-Ω resistor, which reduces the output impedance by a factor of 64 (6.25 kΩ to 98 Ω).
Using this method to generate a voltage you can:
Generate a voltage referenced to ground by sourcing current into a resistor connected to ground. Do not forget
the compliance voltage.
Generate a voltage referenced to the power rail (≤ Vdda) by sinking current from a resistor connected to the
power rail. Do not forget the compliance voltage.
Select any of the current ranges to suit your applications specific needs depending on:
Desired output impedance: a higher current means a lower output impedance for a given voltage range.
Desired power consumption: lower current ranges use less power for the same generated voltage.
Dynamic Voltage Range Adjustments
The ability to change the generated voltage range dynamically is valuable. If you set your midrange voltage from 0 to
500 mV by selecting the 255 µA current range and selecting a 1.96 kΩ conversion resistor, you can:
Change the current range to 32 µA using the API and the output range changes to 0 to 62 mV
Change the current range to 2.048 mA using the API and the output range changes to 0 to 4 V
A dynamic voltage range adjustment provides the ability to change the range of the voltage generated by factors of
eight without changing the external hardware.
Multiplying VDAC
Tying an ‘open drain drives low’ GPIO pin to the IDAC output gives you the ability to pulse width modulate the output
current through a resistor. See Figure 4 and Figure 5 for an example. If the modulated output is then buffered and low
pass filtered, the output approximates a multiplying VDAC where the duty cycle of the PWM is one (input1) input and
the IDAC is the other input (input2). The output will be input1 × input2.
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Figure 4. Multiplying VDAC
Figure 5. Output Waveform of Mixed Signal Multiplying VDAC
“Any Range and Any Ground” VDAC from an IDAC, Resistor and Buffer
Perhaps you need a 65 mV range signal, but it needs to be referenced at 2.5 volts. Your 4 volt VDAC only gives you
16 mV per step, so your sensitive signal range only gets four steps around the 2.5 V range. A clever solution to this
problem is to use an IDAC and resistor to generate the 65 mV voltage range, and then place the low side of the
resistor to 2.5 volts. Figure 6 illustrates this using the 255 µA range and a 245-Ω resistor.
Figure 6. Any Range and Any Ground VDAC
The easiest way to generate 2.5 volts is to use a VDAC, but be aware, the VDAC output resistance is not 0Ω, and the
circuit will not behave as desired. Refer to the datasheet for equivalent output resistance for the different VDAC
modes. To solve this problem, buffer the new “VDAC ground” signal as shown in Figure 7.
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Figure 7. Any Range and Any Ground Implementation
Furthermore, to ensure that the output signal has sufficiently low output impedance, buffer the output voltage as
shown in Figure 8.
Figure 8. Any Range and Any Ground Implementation with Output Buffer
You can rearrange a few things, eliminate an opamp, and gain a few extra features in the process. Refer to Figure 9
for the updated topology.
Figure 9. Transimpedance Amplifier Implementation
The circuit in Figure 9 performs the same as the previous topology (any range, any ground, low output impedance). It
saves an opamp, and the compliance voltage of the IDAC no longer has a significant impact on the output range. The
IDAC sources current into the “negative input” of the opamp, which is kept at the same voltage as the output of the
“ground” VDAC. Thus the desired output voltage no longer affects the IDACs ability to source current by cutting into
its compliance range (as long as the ground voltage set by the VDAC does not violate the compliance voltage of the
Remember that there is finite (non-zero) switch resistance from the IDAC output to the opamp input, which causes a
minor voltage drop. However, the IDAC output can be kept within a few hundred millivolts of the VDAC setting (using
proper IDAC current selection).
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
The polarity of the voltage will be opposite from the previous topologies, but that is easily solved by setting the
direction of the IDAC to sourcing or sinking. There is no significant downside to choosing a smaller IDAC range in this
topology, so internal voltage drop can be eliminated by using the 32 µA range. The output equation is shown in
Equation 2. Voltage increases (+) on Vout if the IDAC direction is "sinking" and voltage decreases (–) on Vout if the
IDAC direction is “sourcing”.
VOUT  VDAC  I DAC * 245
Equation 2
The output impedance of the circuit will be zero and the output voltage range can go as close to the rails as the
opamp will allow.
If a non-standard analog ground is not required (a ground that needs to be generated by a VDAC), then the internal
reference voltages can be used to set an analog ground. To see the circuit, refer to Figure 10. Because the voltage
reference is driven into the high-impedance input of an opamp, it is not necessary to buffer the relatively weak
reference voltages.
Figure 10. Transimpedance Amplifier VDAC Biased at VDDA/2
Rail-to-Rail 9-Bit VDAC with Low Output Impedance
The topology of the circuit in Figure 10 allows to turn an 8-bit IDAC, a resistor, and an opamp into a rail-to-rail, lowoutput impedance 9-bit VDAC. With a 5-V system as an example, use VDDA/2 as the voltage into the non-inverting
terminal of the opamp shown in Figure 10. You can then select the 255 µA current range and choose a resistor that
gave us half of our range (2.5 volts) at full scale on the IDAC (2.5 V / 255 µA = 9.8 kΩ). See Figure 11 for more
information. Check the relevant datasheet specification to determine how close to the rails the opamp can go.
Figure 11. 9-Bit Voltage DAC Hardware
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
When the components are connected as shown in Figure 11, you can generate voltages from 0 to 5 volts by
changing the direction of the IDAC. The direction can be changed through software or hardware, depending on the
configuration. Table 1 gives a few examples to show how to reach the entire voltage range with this topology.
Table 1. Voltage Output With Sinking and Sourcing IDAC into a VDDA/2 Biased TIA
IDAC Current Setting
IDAC Direction
Output Voltage
255 µA
192 µA
128 µA
64 µA
0 µA
64 µA
128 µA
192 µA
255 µA
Changing the IDAC direction allows you to turn an 8-bit IDAC into a 9-bit VDAC (255 steps above VDDA/2 and 255
steps below VDDA/2), with just an opamp and a resistor. Adding a capacitor in parallel with the resistor, as shown in
Figure 12, provides a low pass filter on the output with a cutoff frequency set by Equation 3.
fc 
Equation 3
To ensure the best accuracy, load the proper calibration values when the IDAC direction or range is switched. This
can be done with software or DMA.
Figure 12. 9 Bit VDAC with Integrated Low Pass Filter
IDAC Current Multiplier
If you need a special IDAC range that the PSoC 3 and PSoC 5LP cannot reach with its three modes, then using an
opamp and two resistors, make the current scaling circuit shown in Figure 13. Equation 4 governs the output current.
I out  I DAC *
Equation 4
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Figure 13. Current Multiplier Circuit
In this circuit, the output current has the opposite polarity of the IDAC. Remember these design considerations:
The ratio of the resistors sets the current scale. For example, if R1 = 10 kΩ and R2 = 20 kΩ, the circuit will
behave the same if R1 = 1 Ω and R2 = 2 Ω.
If the resistors are large (greater than 1 kΩ), then there is a significant voltage drop across them. Take care
to ensure that the opamp has sufficient headroom to operate. However, large resistors are more tolerant of
input offset voltage introducing error (as an offset current) into the current ratio.
If the resistors are small (less than 100 Ω), then there is more headroom to operate, because the voltage
drop across the resistors are small. However, the error introduced by the input offset voltage of the opamp
will be more significant.
The load connected to the output node determines the voltage that the circuit will operate at. Take care to ensure
that the IDAC compliance voltage is not violated and that the opamp has sufficient headroom to operate.
This application note presents few of the many possible ways you can use the highly flexible IDACs in PSoC 3 and
PSoC 5LP. With these versatile tools, you can create unique applications and uses that are simply not possible
otherwise. PSoC Rocks!
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Document History
Document Title: AN60305 - Using PSoC 3 and PSoC 5LP IDACs to Build a Better VDAC
Document Number: 001-60305
Orig. of
Description of Change
New application note
Changed title from ‘PSoC® 3 and 5 IDAC Tips and Tricks’ to ‘Using IDACs to Build
a Better VDAC’.
Updated title to AN60305 - Using PSoC® 3 and PSoC 5 IDACS to Build a Better
Updated document title to read as “Using PSoC® 3 and PSoC 5LP IDACs to Build
a Better VDAC - AN60305”.
Replaced “PSoC 5” with “PSoC 5LP” in all instances across the document.
Updated the document template.
Sunset ECN, no change
Fixed the template. Removed the About the Author section.
Sunset ECN, no change for application note contents.
Removed an obsolete e-mail link and then added a proper Cypress supporting
web page.
Updated the product related links – Added PSoC 4 and ARM® Cortex®
Document No. 001-60305 Rev. *F
Using PSoC® 3 and PSoC 5LP IDACs to Build a Better VDAC
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find
the office closest to you, visit us at Cypress Locations.
PSoC® Solutions
ARM Cortex Microcontrollers
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Clocks & Buffers
Lighting & Power Control
Touch Sensing
USB Controllers
Cypress Developer Community
Community | Forums | Blogs | Video | Training
Technical Support
PSoC is a registered trademark of Cypress Semiconductor Corp. Programmable System-on-Chip and PSoC Creator are trademarks of Cypress
Semiconductor Corp. All other trademarks or registered trademarks referenced herein are the property of their respective owners.
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
: 408-943-2600
: 408-943-4730
© Cypress Semiconductor Corporation, 2010-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including
Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by
Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such
laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with
Cypress governing the use of the Software, then Cypress hereby grants you under its copyright rights in the Software, a personal, non-exclusive,
nontransferable license (without the right to sublicense) (a) for Software provided in source code form, to modify and reproduce the Software solely for
use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end
users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units. Cypress also grants you a
personal, non-exclusive, nontransferable, license (without the right to sublicense) under those claims of Cypress’s patents that are infringed by the
Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely to the minimum extent that is necessary for you
to exercise your rights under the copyright license granted in the previous sentence. Any other use, reproduction, modification, translation, or
compilation of the Software is prohibited.
Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application
or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or
programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test
the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or
authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, lifesupport devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous
substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended
Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the
device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and Company shall and hereby does release Cypress
from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. Company shall indemnify and hold
Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related
to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or
registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit Other
names and brands may be claimed as property of their respective owners.
Document No. 001-60305 Rev. *F
Similar pages