LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only TAPE AND BOX TYPE LED LAMPS LWK3333-50/P1/TBS-X DATA SHEET DOC. NO : REV. : DATE : QW0905-LWK3333-50/P1/TBS-X A 13 - Oct. - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LWK3333-50/P1/TBS-X Page 1/6 Package Dimensions ΔH P2 H2 W2 H1 L W0 W1 W3 D P1 F P T LWK3333-50/P1 5.0 5.9 7.6 8.6 11.6±0.5 1.5MAX □0.5 TYP 25.0MIN 1.0MIN 2.54TYP + - Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/6 PART NO. LWK3333-50/P1/TBS-X Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT WK Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 100 mA Power Dissipation PD 120 mW Ir 50 μA Electrostatic Discharge( * ) ESD 150 V Operating Temperature Topr -20~ +80 ℃ Storage Temperature Tstg -30~ +100 ℃ Soldering Temperature Tsol Reverse Current @5V Max 260 ℃ for 5 sec Max (2mm from body) Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic * glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO MATERIAL COLOR Emitted Lens LWK3333-50/P1/TBS-X InGaN/GaN White Water Clear Chromaticity Coordinates X Y 0.28 0.28 Forward Luminous Viewing voltage intensity angle @20mA(V) @20mA(mcd) 2θ 1/2 (deg) Typ. Max. Min. Typ. 3.5 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 4.0 1800 3400 50 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/6 PART NO. LWK3333-50/P1/TBS-X . Chromaticity Coordinates Specifications for Bin Grading BIN A1 A2 A3 A4 A5 X Y 0.21 0.190 0.21 0.150 0.22 0.165 0.22 0.22 0.22 0.165 0.23 0.23 X Y X Y 0.26 0.265 0.26 0.225 0.31 0.340 0.31 0.300 0.27 0.240 0.32 0.315 0.205 0.27 0.205 0.27 0.280 0.32 0.355 0.280 0.32 0.355 0.27 0.240 0.32 0.315 0.180 0.28 0.220 0.28 0.255 0.33 0.330 0.295 0.33 0.370 0.23 0.220 0.28 0.295 0.33 0.370 0.23 0.180 0.24 0.195 0.28 0.255 0.33 0.330 0.29 0.270 0.34 0.345 0.24 0.235 0.29 0.310 0.34 0.385 0.24 0.235 0.29 0.310 0.34 0.385 0.24 0.195 0.29 0.270 0.34 0.345 0.25 0.210 0.30 0.285 0.35 0.360 0.25 0.250 0.30 0.325 0.35 0.400 0.25 0.250 0.30 0.325 0.25 0.210 0.30 0.285 0.26 0.225 0.31 0.300 0.26 0.265 0.31 0.340 . CIE Chromaticity Diagram BIN B1 B2 B3 B4 B5 BIN C1 C2 C3 C4 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LWK3333-50/P1/TBS-X Page 4/6 •Dimension Symbol Information SPECIFICATIONS OPTION SYMBOL CODE SYMBOL ITEMS Minimum Maximum mm inch mm inch Tape Feed Hole Diameter ------- D 3.8 0.15 4.2 0.17 Component Lead Pitch ------- F 2.3 0.09 3.0 0.12 Front-To-Rear Deflection ------- △H ------- ------- 2.0 0.08 TBS-1 17.5 0.69 18.5 0.73 TBS-2 21.5 0.85 22.5 0.89 TBS-3 25.5 1.0 26.5 1.04 TBS-5 22.5 0.89 23.5 0.93 TBS-6 19.9 0.78 20.9 0.82 24.0 0.94 25.0 0.98 24.5 0.96 25.5 1.0 TBS-9 19.0 0.75 20.0 0.79 TBS-10 18.4 0.72 19.4 0.76 TBS-11 21.0 0.83 22.0 0.87 TBS-12 20.5 0.81 21.5 0.85 TBS-13 18.0 0.71 19.0 0.75 ------- 36 1.42 11 0.43 TBS-7 Feed Hole To Bottom Of Component H1 TBS-8 Feed Hole To Overall Component Height ------- H2 Lead Length After Component Height ------- L Feed Hole Pitch ------- P 12.4 0.49 13 0.51 Lead Location ------- P1 4.4 0.17 5.8 0.23 Center Of Component Location ------- P2 5.1 0.2 7.7 0.3 Overall Taped Package Thickness ------- T ------- ------- 1.42 0.06 Feed Hole Location ------- W0 8.5 0.33 9.75 0.38 Adhesive Tape Width ------- W1 14.5 0.57 15.5 0.61 Adhesive Tape Position ------- W2 0 0 4.0 0.16 Tape Width ------- W3 17.5 0.69 19 0.75 ------- W0 REMARK:TBS=Tape And Box Straight Leads • Dimensions Symbol Information • Package Dimensions Specification Description Symbol minimum maxmum mm inch mm inch Overall Length L 330 13.0 340 13.4 Overall Width W 265 10.4 275 10.8 Overall Thickness H 50 1.97 60 2.4 Quantity/Box 2000PCS LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/6 PART NO. LWK3333-50/P1/TBS-X Typical Electro-Optical Characteristics Curve WK CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1 01 2.5 2.0 1.5 1.0 0.5 0.0 1.0 2.0 3.0 4.0 5.0 1 10 Fig.4 Relative Intensity vs. Temperature 1.2 Relative Intensity@20mA Normalize @25℃ Forward Voltage@20mA Normalize @25℃ Fig.3 Forward Voltage vs. Temperature 1.1 1.0 0.9 0.8 -20 0 20 40 60 80 100 SPECTRAL RADIANCE 100 Intensity 80 60 40 20 0 600 Wavelength (nm) 700 2.5 2.0 1.5 1.0 0.5 0.0 -20 0 20 40 60 80 Ambient Temperature( ℃) Fig.5 Luminous Spectrum(Ta=25 ℃) 500 3.0 -40 Ambient Temperature( ℃) 400 1000 Forward Current(mA) Forward Voltage(V) -40 100 800 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/6 PART NO. LWK3333-50/P1/TBS-X Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resisance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under ondition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hous. Thermal Shock Test 1.Ta=105 ℃±5 ℃&-40 ℃±5 ℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11