CYPRESS CY2305SC-1HT

CY2305, CY2309
Low Cost 3.3V Zero Delay Buffer
Features
Functional Description
■
10 MHz to 100/133 MHz operating range, compatible with CPU
and PCI bus frequencies
■
Zero input-output propagation delay
■
60 ps typical cycle-to-cycle jitter (high drive)
■
Multiple low skew outputs
❐ 85 ps typical output-to-output skew
❐ One input drives five outputs (CY2305)
❐ One input drives nine outputs, grouped as 4 + 4 + 1 (CY2309)
The CY2309 is a low cost 3.3V zero delay buffer designed to
distribute high speed clocks and is available in a 16-pin SOIC or
TSSOP package. The CY2305 is an 8-pin version of the
CY2309. It accepts one reference input, and drives out five low
skew clocks. The -1H versions of each device operate at up to
100-/133 MHz frequencies, and have higher drive than the -1
devices. All parts have on-chip PLLs which lock to an input clock
on the REF pin. The PLL feedback is on-chip and is obtained
from the CLKOUT pad.
■
Compatible with Pentium-based systems
■
Test Mode to bypass phase-locked loop (PLL) (CY2309 only
[see “Select Input Decoding” on page 3])
■
Available in space-saving 16-pin 150-mil SOIC or 4.4-mm
TSSOP packages (CY2309), and 8-pin, 150-mil SOIC package
(CY2305)
■
3.3V operation
■
Industrial temperature available
The CY2309 has two banks of four outputs each, which can be
controlled by the select inputs as shown in the “Select Input
Decoding” table on page 3. If all output clocks are not required,
BankB can be three-stated. The select inputs also allow the input
clock to be directly applied to the outputs for chip and system
testing purposes.
The CY2305 and CY2309 PLLs enter a power down mode when
there are no rising edges on the REF input. In this state, the
outputs are three-stated and the PLL is turned off, resulting in
less than 25.0 μA current draw for these parts. The CY2309 PLL
shuts down in one additional case as shown in the table below.
Multiple CY2305 and CY2309 devices can accept the same input
clock and distribute it. In this case, the skew between the outputs
of two devices is guaranteed to be less than 700 ps.
The CY2305/CY2309 is available in two/three different
configurations, as shown in the ordering information (page 10).
The CY2305-1/CY2309-1 is the base part. The CY2305-1H/
CY2309-1H is the high drive version of the -1, and its rise and
fall times are much faster than the -1s.
Logic Block Diagram
PLL
MUX
REF
CLKOUT
CLKA1
CLKA2
CLKA3
CLKA4
CLKB1
S2
Select Input
Decoding
CLKB2
CLKB3
S1
CLKB4
Cypress Semiconductor Corporation
Document #: 38-07140 Rev. *J
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 12, 2009
[+] Feedback
CY2305, CY2309
Pinouts
Figure 1. Pin Diagram - CY2305
REF
CLK2
CLK1
GND
1
8
2
7
3
6
4
5
CLKOUT
CLK4
VDD
CLK3
Table 1. Pin Description for CY2305
Pin
Signal
[1]
Description
1
Input reference frequency, 5V tolerant input
REF
2
CLK2[2]
Buffered clock output
3
CLK1[2]
Buffered clock output
4
GND
Ground
5
CLK3[2]
Buffered clock output
6
VDD
3.3V supply
7
CLK4[2]
Buffered clock output
8
CLKOUT[2]
Buffered clock output, internal feedback on this pin
Figure 2. Pin Diagram - CY2309
REF
CLKA1
1
16
2
15
CLKA2
VDD
3
14
4
13
GND
CLKB1
CLKB2
S2
5
12
6
11
7
10
8
9
CLKOUT
CLKA4
CLKA3
VDD
GND
CLKB4
CLKB3
S1
Table 2. Pin Description for CY2309
Pin
Signal
Description
1
REF[1]
Input reference frequency, 5V tolerant input
2
CLKA1[2]
Buffered clock output, Bank A
3
CLKA2[2]
Buffered clock output, Bank A
4
VDD
3.3V supply
5
GND
Ground
6
CLKB1[2]
Buffered clock output, Bank B
7
CLKB2[2]
Buffered clock output, Bank B
8
S2[3]
Select input, bit 2
9
S1[3]
Select input, bit 1
10
CLKB3[2]
11
[2]
CLKB4
Buffered clock output, Bank B
12
GND
Ground
Buffered clock output, Bank B
Notes
1. Weak pull down.
2. Weak pull down on all outputs.
3. Weak pull ups on these inputs.
Document #: 38-07140 Rev. *J
Page 2 of 15
[+] Feedback
CY2305, CY2309
Table 2. Pin Description for CY2309
Pin
Signal
Description
13
VDD
14
CLKA3[2]
Buffered clock output, Bank A
15
[2]
Buffered clock output, Bank A
3.3V supply
CLKA4
[2]
16
Buffered output, internal feedback on this pin
CLKOUT
Select Input Decoding for CY2309
S2
S1
CLOCK A1–A4
CLOCK B1–B4
CLKOUT[4]
Output Source
PLL Shutdown
0
0
Three-state
Three-state
Driven
PLL
N
0
1
Driven
Three-state
Driven
PLL
N
1
0
Driven
Driven
Driven
Reference
Y
1
1
Driven
Driven
Driven
PLL
N
Figure 3. REF. Input to CLKA/CLKB Delay vs. Loading Difference between CLKOUT and CLKA/CLKB Pins
Zero Delay and Skew Control
All outputs must be uniformly loaded to achieve Zero Delay between the input and output. Because the CLKOUT pin is the internal
feedback to the PLL, its relative loading can adjust the input-output delay. This is shown in the above graph.
For applications requiring zero input-output delay, all outputs, including CLKOUT, must be equally loaded. Even if CLKOUT is not
used, it must have a capacitive load, equal to that on other outputs, for obtaining zero input-output delay. If input to output delay
adjustments are required, use the above graph to calculate loading differences between the CLKOUT pin and other outputs.
For zero output-output skew, be sure to load all outputs equally. For further information refer to the application note titled “CY2305
and CY2309 as PCI and SDRAM Buffers.”
Note
4. This output is driven and has an internal feedback for the PLL. The load on this output can be adjusted to change the skew between the reference and output.
Document #: 38-07140 Rev. *J
Page 3 of 15
[+] Feedback
CY2305, CY2309
Absolute Maximum Conditions
Supply Voltage to Ground Potential................–0.5V to +7.0V
Junction Temperature ................................................. 150°C
DC Input Voltage (Except REF) ............ –0.5V to VDD + 0.5V
Static Discharge Voltage
(per MIL-STD-883, Method 3015) ........................... > 2,000V
DC Input Voltage REF .........................................–0.5V to 7V
Storage Temperature ................................. –65°C to +150°C
Operating Conditions for CY2305SC-XX and CY2309SC-XX Commercial Temperature Devices
Parameter
Description
Min
Max
Unit
3.0
3.6
V
0
70
°C
VDD
Supply Voltage
TA
Operating Temperature (Ambient Temperature)
CL
Load Capacitance, below 100 MHz
–
30
pF
CL
Load Capacitance, from 100 MHz to 133 MHz
–
10
pF
CIN
Input Capacitance
tPU
Power up time for all VDDs to reach minimum specified voltage (power
ramps must be monotonic)
–
7
pF
0.05
50
ms
Electrical Characteristics for CY2305SC-XX and CY2309SC-XX Commercial Temperature
Devices
Parameter
VIL
Description
Input LOW
Voltage[5]
Voltage[5]
VIH
Input HIGH
IIL
Input LOW Current
IIH
Input HIGH Current
Voltage[6]
VOL
Output LOW
VOH
Output HIGH Voltage[6]
Test Conditions
Min
Max
Unit
–
0.8
V
2.0
–
V
–
50.0
μA
VIN = VDD
–
100.0
μA
IOL = 8 mA (–1)
IOH = 12 mA (–1H)
–
0.4
V
2.4
–
V
VIN = 0V
IOH = –8 mA (–1)
IOL = –12 mA (–1H)
IDD (PD mode) Power Down Supply Current
REF = 0 MHz
–
12.0
μA
IDD
Unloaded outputs at 66.67 MHz,
SEL inputs at VDD
–
32.0
mA
Supply Current
Switching Characteristics for CY2305SC-1 and CY2309SC-1 Commercial Temperature
Devices
Parameter[7]
Name
Test Conditions
Min
Typ.
Max
Unit
10
10
–
100
133.33
MHz
MHz
40.0
50.0
60.0
%
t1
Output Frequency
30-pF load
10 pF load
tDC
Duty Cycle[6] = t2 ÷ t1
Measured at 1.4V, Fout = 66.67
MHz
t3
Rise Time[6]
Measured between 0.8V and 2.0V
–
–
2.50
ns
Measured between 0.8V and 2.0V
–
–
2.50
ns
All outputs equally loaded
–
85
250
ps
Measured at VDD/2
–
0
±350
ps
t4
Fall
Time[6]
Skew[6]
t5
Output to Output
t6A
Delay, REF Rising Edge to
CLKOUT Rising Edge[6]
Notes
5. REF input has a threshold voltage of VDD/2.
6. Parameter is guaranteed by design and characterization. Not 100% tested in production.
Document #: 38-07140 Rev. *J
Page 4 of 15
[+] Feedback
CY2305, CY2309
Switching Characteristics for CY2305SC-1 and CY2309SC-1 Commercial Temperature
Devices
Parameter[7]
Name
Test Conditions
Min
Typ.
Max
Unit
t6B
Delay, REF Rising Edge to
CLKOUT Rising Edge[6]
Measured at VDD/2. Measured in
PLL Bypass Mode, CY2309 device
only.
1
5
8.7
ns
t7
Device to Device Skew[6]
Measured at VDD/2 on the
CLKOUT pins of devices
–
–
700
ps
tJ
Cycle to Cycle Jitter[6]
Measured at 66.67 MHz, loaded
outputs
–
70
200
ps
tLOCK
PLL Lock Time[6]
Stable power supply, valid clock
presented on REF pin
–
–
1.0
ms
Switching Characteristics for CY2305SC-1H and CY2309SC-1H Commercial Temperature
Devices
Parameter[7]
Name
Description
Min
Typ.
Max
Unit
10
10
–
100
133.33
MHz
MHz
Measured at 1.4V, Fout = 66.67 MHz
40.0
50.0
60.0
%
Measured at 1.4V, Fout < 50 MHz
45.0
50.0
55.0
%
Measured between 0.8V and 2.0V
–
–
1.50
ns
Measured between 0.8V and 2.0V
–
–
1.50
ns
All outputs equally loaded
–
85
250
ps
t1
Output Frequency
30 pF load
10 pF load
tDC
Duty Cycle[6] = t2 ÷ t1
tDC
t3
t4
Duty
Cycle[6]
Rise
Time[6]
Fall
= t2 ÷ t1
Time[6]
Skew[6]
t5
Output to Output
t6A
Delay, REF Rising Edge to
CLKOUT Rising Edge[6]
Measured at VDD/2
–
–
±350
ps
t6B
Delay, REF Rising Edge to
CLKOUT Rising Edge[6]
Measured at VDD/2. Measured in
PLL Bypass Mode, CY2309 device
only.
1
5
8.7
ns
t7
Device to Device Skew[6]
Measured at VDD/2 on the CLKOUT
pins of devices
–
–
700
ps
t8
Output Slew Rate[6]
Measured between 0.8V and 2.0V
using Test Circuit #2
1
–
tJ
Cycle to Cycle Jitter[6]
Measured at 66.67 MHz, loaded
outputs
–
60
200
ps
tLOCK
PLL Lock Time[6]
Stable power supply, valid clock
presented on REF pin
–
–
1.0
ms
V/ns
Operating Conditions for CY2305SI-XX and CY2309SI-XX Industrial Temperature Devices
Parameter
Description
Min
Max
Unit
VDD
Supply Voltage
3.0
3.6
V
TA
Operating Temperature (Ambient Temperature)
–40
85
°C
CL
Load Capacitance, below 100 MHz
–
30
pF
CL
Load Capacitance, from 100 MHz to 133 MHz
–
10
pF
CIN
Input Capacitance
–
7
pF
Note
7. All parameters specified with loaded outputs.
Document #: 38-07140 Rev. *J
Page 5 of 15
[+] Feedback
CY2305, CY2309
Electrical Characteristics for CY2305SI-XX and CY2309SI-XX Industrial Temperature Devices
Parameter
VIL
Description
Input LOW
Test Conditions
Voltage[5]
[5]
Min
Max
Unit
–
0.8
V
2.0
–
V
VIH
Input HIGH Voltage
IIL
Input LOW Current
VIN = 0V
–
50.0
μA
IIH
Input HIGH Current
VIN = VDD
–
100.0
μA
VOL
Output LOW Voltage[6]
IOL = 8 mA (–1)
IOH =12 mA (–1H)
–
0.4
V
VOH
Output HIGH Voltage[6]
IOH = –8 mA (–1)
IOL = –12 mA (–1H)
2.4
–
V
REF = 0 MHz
–
25.0
μA
Unloaded outputs at 66.67 MHz, SEL inputs at VDD
–
35.0
mA
IDD (PD mode) Power Down Supply
Current
IDD
Supply Current
Switching Characteristics for CY2305SI-1 and CY2309SI-1 Industrial Temperature Devices
Parameter[7]
Name
Test Conditions
Min
Typ
Max
Unit
10
10
–
100
133.33
MHz
MHz
40.0
50.0
60.0
%
Measured between 0.8V and 2.0V
–
–
2.50
ns
Measured between 0.8V and 2.0V
–
–
2.50
ns
All outputs equally loaded
–
85
250
ps
t1
Output Frequency
30 pF load
10 pF load
tDC
Duty Cycle[6] = t2 ÷ t1
Measured at 1.4V, Fout = 66.67 MHz
t3
t4
[6]
Rise Time
Fall
Time[6]
Skew[6]
t5
Output to Output
t6A
Delay, REF Rising Edge to Measured at VDD/2
CLKOUT Rising Edge[6]
–
–
±350
ps
t6B
Delay, REF Rising Edge to Measured at VDD/2. Measured in PLL Bypass Mode,
CLKOUT Rising Edge[6] CY2309 device only.
1
5
8.7
ns
t7
Device to Device Skew[6] Measured at VDD/2 on the CLKOUT pins of devices
–
–
700
ps
Measured at 66.67 MHz, loaded outputs
–
70
200
ps
Stable power supply, valid clock presented on REF
pin
–
–
1.0
ms
tJ
tLOCK
Cycle to Cycle
PLL Lock
Jitter[6]
Time[6]
Switching Characteristics for CY2305SI-1H and CY2309SI-1H Industrial Temperature Devices
Parameter[7]
Name
Description
Min
Typ
Max
Unit
10
10
–
100
133.33
MHz
MHz
60.0
%
t1
Output Frequency
30 pF load
10 pF load
tDC
Duty Cycle[6] = t2 ÷ t1
Measured at 1.4V, Fout = 66.67 MHz
40.0
50.0
Measured at 1.4V, Fout < 50 MHz
45.0
50.0
55.0
%
Measured between 0.8V and 2.0V
–
–
1.50
ns
Measured between 0.8V and 2.0V
–
–
1.50
ns
All outputs equally loaded
–
85
250
ps
Duty
Cycle[6]
t3
Rise
Time[6]
t4
Fall Time[6]
tDC
= t2 ÷ t1
Skew[6]
t5
Output to Output
t6A
Delay, REF Rising Edge to Measured at VDD/2
CLKOUT Rising Edge[6]
–
–
±350
ps
t6B
Delay, REF Rising Edge to Measured at VDD/2. Measured in PLL Bypass Mode,
CLKOUT Rising Edge[6] CY2309 device only.
1
5
8.7
ns
t7
Device to Device Skew[6] Measured at VDD/2 on the CLKOUT pins of devices
–
–
700
ps
Document #: 38-07140 Rev. *J
Page 6 of 15
[+] Feedback
CY2305, CY2309
Switching Characteristics for CY2305SI-1H and CY2309SI-1H Industrial Temperature Devices
Parameter[7]
Name
[6]
t8
Output Slew Rate
tJ
Cycle to Cycle Jitter[6]
tLOCK
[6]
PLL Lock Time
Description
Min
Typ
Max
Unit
Measured between 0.8V and 2.0V using Test Circuit
#2
1
–
–
V/ns
Measured at 66.67 MHz, loaded outputs
–
60
200
ps
Stable power supply, valid clock presented on REF
pin
–
–
1.0
ms
Switching Waveforms
Figure 4. Duty Cycle Timing
t1
t2
1.4V
1.4V
1.4V
Figure 5. All Outputs Rise/Fall Time
OUTPUT
2.0V
0.8V
2.0V
0.8V
3.3V
0V
t4
t3
Figure 6. Output-Output Skew
OUTPUT
1.4V
1.4V
OUTPUT
t5
Figure 7. Input-Output Propagation Delay
INPUT
VDD/2
VDD/2
OUTPUT
t6
Figure 8. Device-Device Skew
CLKOUT, Device 1
VDD/2
VDD/2
CLKOUT, Device 2
t7
Document #: 38-07140 Rev. *J
Page 7 of 15
[+] Feedback
CY2305, CY2309
Typical Duty Cycle[8] and IDD Trends[9] for CY2305-1 and CY2309-1
Duty Cycle Vs VDD
(for 15 pF Loads over Frequency - 3.3V, 25C)
60
60
58
58
56
56
54
52
33 MHz
50
66 MHz
48
100 MHz
46
Duty Cycle (% )
Duty Cycle (% )
Duty Cycle Vs VDD
(for 30 pF Loads over Frequency - 3.3V, 25C)
54
66 MHz
50
100 MHz
48
133 MHz
46
44
44
42
42
40
33 MHz
52
40
3
3.1
3.2
3.3
3.4
3.5
3.6
3
3.1
3.2
VDD (V)
Duty Cycle Vs Frequency
(for 30 pF Loads over Temperature - 3.3V)
60
60
58
58
3.5
3.6
56
54
-40C
52
0C
50
25C
48
70C
46
85C
Duty Cycle (%)
Duty Cycle (%)
3.4
Duty Cycle Vs Frequency
(for 15 pF Loads over Temperature - 3.3V)
56
54
-40C
52
0C
50
25C
48
70C
46
85C
44
44
42
42
40
40
20
40
60
80
100
120
140
20
40
60
Frequency (MHz)
80
100
120
140
Frequency (MHz)
IDD vs Number of Loaded Outputs
(for 30 pF Loads over Frequency - 3.3V, 25C)
IDD vs Number of Loaded Outputs
(for 15 pF Loads over Frequency - 3.3V, 25C)
140
140
120
120
100
33 MHz
80
66 MHz
60
100 MHz
IDD (mA)
100
IDD (mA)
3.3
VDD (V)
33 MHz
80
66 MHz
60
40
40
20
20
100 MHz
0
0
0
1
2
3
4
5
6
# of Loaded Outputs
7
8
9
0
1
2
3
4
5
6
7
8
9
# of Loaded Outputs
Notes
8. Duty cycle is taken from typical chip measured at 1.4V.
9. IDD data is calculated from IDD = ICORE + nCVf, where ICORE is the unloaded current. (n = # of outputs; C = Capacitance load per output (F); V = Supply Voltage (V);
f = frequency (Hz)).
Document #: 38-07140 Rev. *J
Page 8 of 15
[+] Feedback
CY2305, CY2309
Typical Duty Cycle[8] and IDD Trends[9] for CY2305-1H and CY2309-1H
Duty Cycle Vs VDD
(for 15 pF Loads over Frequency - 3.3V, 25C)
60
60
58
58
56
56
54
52
33 MHz
50
66 MHz
48
100 MHz
46
Duty Cycle (% )
Duty Cycle (% )
Duty Cycle Vs VDD
(for 30 pF Loads over Frequency - 3.3V, 25C)
54
66 MHz
50
100 MHz
48
133 MHz
46
44
44
42
42
40
33 MHz
52
40
3
3.1
3.2
3.3
3.4
3.5
3.6
3
3.1
3.2
3.3
VDD (V)
Duty Cycle Vs Frequency
(for 30 pF Loads over Temperature - 3.3V)
60
60
58
58
3.6
56
54
-40C
52
0C
50
25C
48
70C
46
85C
Duty Cycle (%)
Duty Cycle (%)
3.5
Duty Cycle Vs Frequency
(for 15 pF Loads over Temperature - 3.3V)
56
54
-40C
52
0C
50
25C
48
70C
46
85C
44
44
42
42
40
40
20
40
60
80
100
120
140
20
40
60
80
Frequency (MHz)
100
120
140
Frequency (MHz)
IDD vs Number of Loaded Outputs
(for 30 pF Loads over Frequency - 3.3V, 25C)
IDD vs Number of Loaded Outputs
(for 15 pF Loads over Frequency - 3.3V, 25C)
160
160
140
140
120
120
100
33 MHz
80
66 MHz
60
100 MHz
IDD (mA)
IDD (mA)
3.4
VDD (V)
100
80
33 MHz
60
66 MHz
100 MHz
40
40
20
20
0
0
0
1
2
3
4
5
6
# of Loaded Outputs
Document #: 38-07140 Rev. *J
7
8
9
0
1
2
3
4
5
6
7
8
9
# of Loaded Outputs
Page 9 of 15
[+] Feedback
CY2305, CY2309
Test Circuits
Test Circuit # 1
Test Circuit # 2
V DD
V DD
CLK
0.1 μ F
0.1 μ F
out
1 kΩ
OUTPUTS
OUTPUTS
10 pF
C LOAD
V DD
0.1 μ F
GND
1 kΩ
V DD
0.1 μ F
GND
GND
GND
For parameter t8 (output slew rate) on -1H devices
Ordering Information for CY2305
Ordering Code
Package Type
Operating Range
CY2305SC-1[10]
8-pin 150-mil SOIC
Commercial
CY2305SC-1T[10]
8-pin 150-mil SOIC – Tape and Reel
Commercial
CY2305SI-1[10]
8-pin 150-mil SOIC
Industrial
CY2305SI-1T[10]
8-pin 150-mil SOIC – Tape and Reel
Industrial
CY2305SC-1H[10]
8-pin 150-mil SOIC
Commercial
CY2305SC-1HT[10]
8-pin 150-mil SOIC – Tape and Reel
Commercial
CY2305SI-1H[10]
8-pin 150-mil SOIC
Industrial
CY2305SI-1HT[10]
8-pin 150-mil SOIC – Tape and Reel
Industrial
CY2305SXC-1
8-pin 150-mil SOIC
Commercial
CY2305SXC-1T
8-pin 150-mil SOIC – Tape and Reel
Commercial
CY2305SXI-1
8-pin 150-mil SOIC
Industrial
CY2305SXI-1T
8-pin 150-mil SOIC – Tape and Reel
Industrial
CY2305SXC-1H
8-pin 150-mil SOIC
Commercial
CY2305SXC-1HT
8-pin 150-mil SOIC – Tape and Reel
Commercial
CY2305SXI-1H
8-pin 150-mil SOIC
Industrial
CY2305SXI-1HT
8-pin 150-mil SOIC – Tape and Reel
Industrial
Pb-Free
Ordering Information for CY2309
Ordering Code
[10]
Package Type
Operating Range
16-pin 150-mil SOIC
Commercial
CY2309SC-1T[10]
16-pin 150-mil SOIC – Tape and Reel
Commercial
CY2309SI-1[10]
16-pin 150-mil SOIC
Industrial
CY2309SI-1T[10]
16-pin 150-mil SOIC – Tape and Reel
Industrial
CY2309SC-1H[10]
16-pin 150-mil SOIC
Commercial
CY2309SC-1
Note
10. Not recommended for new designs.
Document #: 38-07140 Rev. *J
Page 10 of 15
[+] Feedback
CY2305, CY2309
Ordering Information for CY2309 (continued)
Ordering Code
[10]
Package Type
Operating Range
16-pin 150-mil SOIC – Tape and Reel
Commercial
16-pin 4.4-mm TSSOP
Commercial
16-pin 4.4-mm TSSOP – Tape and Reel
Commercial
16-pin 150-mil SOIC
Industrial
16-pin 150-mil SOIC – Tape and Reel
Industrial
CY2309SXC-1
16-pin 150-mil SOIC
Commercial
CY2309SXC-1T
16-pin 150-mil SOIC – Tape and Reel
Commercial
CY2309SXI-1
16-pin 150-mil SOIC
Industrial
CY2309SXI-1T
16-pin 150-mil SOIC – Tape and Reel
Industrial
CY2309SXC-1H
16-pin 150-mil SOIC
Commercial
CY2309SXC-1HT
16-pin 150-mil SOIC – Tape and Reel
Commercial
CY2309SXI-1H
16-pin 150-mil SOIC
Industrial
CY2309SXI-1HT
16-pin 150-mil SOIC – Tape and Reel
Industrial
CY2309ZXC-1H
16-pin 4.4-mm TSSOP
Commercial
CY2309ZXC-1HT
16-pin 4.4-mm TSSOP – Tape and Reel
Commercial
CY2309ZXI-1H
16-pin 4.4-mm TSSOP
Industrial
CY2309ZXI-1HT
16-pin 4.4-mm TSSOP – Tape and Reel
Industrial
CY2309SC-1HT
CY2309ZC-1H
[10]
[10]
CY2309ZC-1HT
CY2309SI-1H
[10]
[10]
CY2309SI-1HT
Pb-Free
Document #: 38-07140 Rev. *J
Page 11 of 15
[+] Feedback
CY2305, CY2309
Package Drawing and Dimensions
8 Lead (150 Mil) SOIC
- S08
Figure
8. 8-Pin (150-Mil) SOIC S8
PIN 1 ID
4
1
1. DIMENSIONS IN INCHES[MM] MIN.
MAX.
2. PIN 1 ID IS OPTIONAL,
ROUND ON SINGLE LEADFRAME
RECTANGULAR ON MATRIX LEADFRAME
0.150[3.810]
0.157[3.987]
3. REFERENCE JEDEC MS-012
0.230[5.842]
0.244[6.197]
4. PACKAGE WEIGHT 0.07gms
PART #
S08.15 STANDARD PKG.
5
SZ08.15 LEAD FREE PKG.
8
0.189[4.800]
0.196[4.978]
0.010[0.254]
0.016[0.406]
SEATING PLANE
X 45°
0.061[1.549]
0.068[1.727]
0.004[0.102]
0.050[1.270]
BSC
0.004[0.102]
0.0098[0.249]
0°~8°
0.0075[0.190]
0.0098[0.249]
0.016[0.406]
0.035[0.889]
51-85066-*C
0.0138[0.350]
0.0192[0.487]
16 Lead (150 Mil) SOIC
Figure 9. 16-Pin (150-Mil) SOIC S16
PIN 1 ID
8
1
DIMENSIONS IN INCHES[MM] MIN.
MAX.
REFERENCE JEDEC MS-012
PACKAGE WEIGHT 0.15gms
0.150[3.810]
0.157[3.987]
0.230[5.842]
0.244[6.197]
PART #
S16.15 STANDARD PKG.
SZ16.15 LEAD FREE PKG.
9
16
0.386[9.804]
0.393[9.982]
0.010[0.254]
0.016[0.406]
SEATING PLANE
X 45°
0.061[1.549]
0.068[1.727]
0.004[0.102]
0.050[1.270]
BSC
0°~8°
0.0138[0.350]
0.0192[0.487]
0.004[0.102]
0.0098[0.249]
0.016[0.406]
0.035[0.889]
0.0075[0.190]
0.0098[0.249]
51-85068-*B
Document #: 38-07140 Rev. *J
Page 12 of 15
[+] Feedback
CY2305, CY2309
Package Drawing and Dimensions (continued)
Figure 10. 16-Pin TSSOP 4.40 MM Body Z16.173
PIN 1 ID
DIMENSIONS IN MM[INCHES] MIN.
1
MAX.
REFERENCE JEDEC MO-153
6.25[0.246]
6.50[0.256]
PACKAGE WEIGHT 0.05gms
4.30[0.169]
4.50[0.177]
16
0.65[0.025]
BSC.
0.19[0.007]
0.30[0.012]
1.10[0.043] MAX.
0.25[0.010]
BSC
GAUGE
PLANE
0°-8°
0.076[0.003]
0.85[0.033]
0.95[0.037]
4.90[0.193]
5.10[0.200]
0.05[0.002]
0.15[0.006]
SEATING
PLANE
0.50[0.020]
0.70[0.027]
0.09[[0.003]
0.20[0.008]
51-85091-*A
Document #: 38-07140 Rev. *J
Page 13 of 15
[+] Feedback
CY2305, CY2309
Document History Page
Document Title: CY2305/CY2309 Low Cost 3.3V Zero Delay Buffer
Document Number: 38-07140
Rev.
ECN
Orig. of
Change
Submission
Date
Description of Change
**
110249
SZV
10/19/01
Change from Spec number: 38-00530 to 38-07140
*A
111117
CKN
03/01/02
Added t6B row to the Switching Characteristics Table; also added the letter
“A” to the t6A row
Corrected the table title from CY2305SC-IH and CY2309SC-IH to
CY2305SI-IH and CY2309SI-IH
*B
117625
HWT
10/21/02
Added eight-pin TSSOP packages (CY2305ZC-1 and CY2305ZC-1T) to the
ordering information table.
Added the Tape and Reel option to all the existing packages:
CY2305SC-1T, CY2305SI-1T, CY2305SC-1HT, CY2305SI-1HT,
CY2305ZC-1T, CY2309SC-1T, CY2309SI-1T, CY2309SC-1HT,
CY2309SI-1HT, CY2309ZC-1HT, CY2309ZI-1HT
*C
121828
RBI
12/14/02
Power up requirements added to Operating Conditions information
*D
131503
RGL
12/12/03
Added Lead-free for all the devices in the ordering information table
*E
214083
RGL
See ECN
Added a Lead-free with the new coding for all SOIC devices in the ordering
information table
*F
291099
RGL
See ECN
Added TSSOP Lead-free devices
*G
390582
RGL
See ECN
Added typical values for jitter
*H
2542461
AESA
07/23/08
Updated template. Added Note “Not recommended for new designs.”
Added part number CY2305ESXC-1, CY2305ESXC-1T, CY2305ESXI-1,
CY2305ESXI-1T, CY2305ESXC-1H, CY2305ESXC-1HT, CY2305ESXI-1H,
CY2305ESXI-1HT, CY2309ESXC-1, CY2309ESXC-1T, CY2309ESXI-1,
CY2309ESXI-1T, CY2309ESXC-1H, CY2309ESXC-1HT, CY2309ESXI-1H,
CY2309ESXI-1HT, CY2309EZXC-1H, CY2309EZXC-1HT, CY2309EZXI-1H,
and CY2309EZXI-1HT in ordering information table.
Removed part number CY2305SZC-1, CY2305SZC-1T, CY2305SZI-1,
CY2305SZI-1T, CY2305SZC-1H, CY2305SZC-1HT, CY2305SZI-1H,
CY2305SZI-1HT, CY2309SZC-1, CY2309SZC-1T, CY2309SZI-1,
CY2309SZI-1T, CY2309SZC-1H, CY2309SZC-1HT, CY2309SZI-1H,
CY2309SZI-1HT, CY2309ZZC-1H, CY2309ZZC-1HT, CY2309ZI-1H,
CY2309ZI-1HT, CY2309ZZI-1H, and CY2309ZZI-1HT in Ordering
Information table.
Changed Lead-Free to Pb-Free.
*I
2565153
AESA
09/18/08
Removed part number CY2305ESXC-1, CY2305ESXC-1T, CY2305ESXI-1,
CY2305ESXI-1T, CY2305ESXC-1H, CY2305ESXC-1HT, CY2305ESXI-1H,
CY2305ESXI-1HT, CY2309ESXC-1, CY2309ESXC-1T, CY2309ESXI-1,
CY2309ESXI-1T, CY2309ESXC-1H, CY2309ESXC-1HT, CY2309ESXI-1H,
CY2309ESXI-1HT, CY2309EZXC-1H, CY2309EZXC-1HT, CY2309EZXI-1H,
and CY2309EZXI-1HT in ordering information table.
Removed note references to note 10 in Pb-Free sections of ordering information table.
Changed IDD (PD mode) from 12.0 to 25.0 μA for commercial temperature
devices
Deleted Duty Cycle parameters for Fout < 50 MHz commercial and industrial
devices.
*J
2673353
KVM/PYRS
03/13/09
Reverted IDD (PD mode) and Duty Cycle parameters back to the values in
revision *H:
Changed IDD (PD mode) from 25 to 12 μA for commercial devices.
Added Duty Cycle parameters for Fout < 50 MHz for commercial and industrial
devices.
Document #: 38-07140 Rev. *J
Page 14 of 15
[+] Feedback
CY2305, CY2309
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
Clocks & Buffers
PSoC Solutions
psoc.cypress.com
clocks.cypress.com
General
Low Power/Low Voltage
psoc.cypress.com/solutions
psoc.cypress.com/low-power
Wireless
wireless.cypress.com
Precision Analog
Memories
memory.cypress.com
LCD Drive
psoc.cypress.com/lcd-drive
image.cypress.com
CAN 2.0b
psoc.cypress.com/can
USB
psoc.cypress.com/usb
Image Sensors
psoc.cypress.com/precision-analog
© Cypress Semiconductor Corporation, 2001-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-07140 Rev. *J
Revised March 12, 2009
Page 15 of 15
All product and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback