CAT93C86B D

CAT93C86B
16-Kb Microwire Serial
EEPROM
Description
The CAT93C86B is a 16−Kb Serial EEPROM memory device
which is configured as either registers of 16 bits (ORG pin at VCC) or 8
bits (ORG pin at GND). Each register can be written (or read) serially
by using the DI (or DO) pin. The CAT93C86B features a self−timed
internal write with auto−clear. On−chip Power−On Reset circuit
protects the internal logic against powering up in the wrong state.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
High Speed Operation: 4 MHz (5 V), 2 MHz (1.8 V)
1.8 V (1.65 V*) to 5.5 V Supply Voltage Range
Selectable x8 or x16 Memory Organization
Self−timed Write Cycle with Auto−clear
Sequential Read
Hardware and Software Write Protection
Power−up Inadvertent Write Protection
Low Power CMOS Technology
Program Enable (PE) Pin
1,000,000 Program/Erase Cycles
100 Year Data Retention
Industrial and Extended Temperature Ranges
8−pin PDIP, SOIC, MSOP, TSSOP, 8−pad UDFN, and WLCSP
6−ball Packages
This Device is Pb−Free, Halogen Free/BFR Free, and RoHS
Compliant†
http://onsemi.com
MSOP−8
Z SUFFIX
CASE 846AD
SOIC−8
X SUFFIX
CASE 751BE
WLCSP−6
C6A SUFFIX
PRELIMINARY
PDIP−8
L SUFFIX
CASE 646AA
TSSOP−8
Y SUFFIX
CASE 948AL
CS
1
SK
DI
DO
Pin 1 1
A VCC
VCC
PE
ORG
GND
PDIP (L), SOIC (V, X),
TSSOP (Y),
UDFN (HU4), MSOP (Z)
B
SK
DI
C
GND
DO
PIN FUNCTION
Function
CS
Chip Select
SK
Clock Input
DI
Serial Data Input
DO
Serial Data Output
VCC
Power Supply
GND
GND
Ground
Figure 1. Functional Symbol
ORG
Memory Organization
ORG
DI
CAT93C86B
2
CS
WLCSP*, ** (C6A)
*ORG internally
connected to GND
**PE float
Pin Name
SK
SOIC−8
V SUFFIX
CASE 751BD
PIN CONFIGURATION
VCC
CS
UDFN−8
HU4 SUFFIX
CASE 517AZ
DO
PE
PE
*CAT93C86Bxx−xxL (TA = −205C to +855C)
†For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
Program Enable
Note: When the ORG pin is connected to VCC, the
x16 organization is selected. When it is connected
to ground, the x8 pin is selected. If the ORG pin is
left unconnected, then an internal pull−up device will
select the x16 organization.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
September, 2013 − Rev. 3
1
Publication Order Number:
CAT93C86B/D
CAT93C86B
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
Storage Temperature
−65 to +150
°C
Voltage on Any Pin with Respect to Ground (Note 1)
−0.5 to +6.5
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns.
Table 2. RELIABILITY CHARACTERISTICS (Note 2)
Symbol
Parameter
NEND (Note 3)
TDR
Endurance
Min
Units
1,000,000
Program / Erase Cycles
100
Years
Data Retention
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
3. Block Mode, VCC = 5 V, 25°C.
Table 3. D.C. OPERATING CHARACTERISTICS
(VCC = +1.8 V to +5.5 V, TA = −40°C to +125°C, VCC = +1.65 V to +5.5 V, TA = −20°C to +85°C unless otherwise specified.)
Symbol
Parameter
ICC1
Supply Current (Write)
Write, VCC = 5.0 V
ICC2
Supply Current (Read)
Read, DO open, fSK = 2 MHz, VCC = 5.0 V
ISB1
Standby Current
(x8 Mode)
VIN = GND or VCC
CS = GND, ORG = GND
TA = −40°C to +85°C
TA = −40°C to +125°C
5
Standby Current
(x16 Mode)
VIN = GND or VCC
CS = GND,
ORG = Float or VCC
TA = −40°C to +85°C
1
TA = −40°C to +125°C
3
VIN = GND to VCC
TA = −40°C to +85°C
1
TA = −40°C to +125°C
2
TA = −40°C to +85°C
1
TA = −40°C to +125°C
2
ISB2
ILI
ILO
Input Leakage Current
Test Conditions
Min
Output Leakage
Current
VOUT = GND to VCC
CS = GND
VIL1
Input Low Voltage
4.5 V ≤ VCC < 5.5 V
−0.1
VIH1
Input High Voltage
4.5 V ≤ VCC < 5.5 V
VIL2
Input Low Voltage
1.65 V ≤ VCC < 4.5 V
VIH2
Input High Voltage
1.65 V ≤ VCC < 4.5 V
VOL1
Output Low Voltage
4.5 V ≤ VCC < 5.5 V, IOL = 3 mA
VOH1
Output High Voltage
4.5 V ≤ VCC < 5.5 V, IOH = −400 mA
VOL2
Output Low Voltage
1.65 V ≤ VCC < 4.5 V, IOL = 1 mA
VOH2
Output High Voltage
1.65 V ≤ VCC < 4.5 V, IOH = −100 mA
Max
Units
2
mA
500
mA
2
mA
mA
mA
mA
0.8
V
2
VCC + 1
V
0
VCC x 0.2
V
VCC x 0.7
VCC + 1
V
0.4
V
2.4
V
0.2
VCC − 0.2
V
V
Table 4. PIN CAPACITANCE (Note 4)
Symbol
COUT
CIN
Test
Conditions
Output Capacitance (DO)
Input Capacitance (CS, SK, DI, ORG)
Min
Typ
Max
Units
VOUT = 0 V
5
pF
VIN = 0 V
5
pF
Table 5. POWER−UP TIMING (Notes 4, 5)
Symbol
Parameter
Max
Units
tPUR
Power−up to Read Operation
1
ms
tPUW
Power−up to Write Operation
1
ms
http://onsemi.com
2
CAT93C86B
Table 6. A.C. TEST CONDITIONS
Input Rise and Fall Times
≤ 50 ns
Input Pulse Voltages
0.4 V to 2.4 V
4.5 V ≤ VCC ≤ 5.5 V
Timing Reference Voltages
0.8 V, 2.0 V
4.5 V ≤ VCC ≤ 5.5 V
Input Pulse Voltages
0.2 VCC to 0.7 VCC
1.65 V ≤ VCC ≤ 4.5 V
Timing Reference Voltages
0.5 VCC
1.65 V ≤ VCC ≤ 4.5 V
Output Load
Current Source IOLmax/IOHmax; CL = 100 pF
4. These parameters are tested initially and after a design or process change that affects the parameter.
5. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
Table 7. A.C. CHARACTERISTICS
(VCC = +1.8 V to +5.5 V, TA = −40°C to +125°C, VCC = +1.65 V to +5.5 V, TA = −20°C to +85°C unless otherwise specified.)
VCC < 4.5 V
Symbol
Min
Parameter
VCC > 4.5 V
Max
Min
Max
Units
tCSS
CS Setup Time
50
50
ns
tCSH
CS Hold Time
0
0
ns
tDIS
DI Setup Time
100
50
ns
tDIH
DI Hold Time
100
50
ns
tPD1
Output Delay to 1
0.25
0.1
ms
tPD0
Output Delay to 0
0.25
0.1
ms
Output Delay to High−Z
100
100
ns
5
5
ms
tHZ (Note 6)
tEW
Program/Erase Pulse Width
tCSMIN
Minimum CS Low Time
0.25
0.1
ms
tSKHI
Minimum SK High Time
0.25
0.1
ms
tSKLOW
Minimum SK Low Time
0.25
0.1
ms
tSV
Output Delay to Status Valid
SKMAX
Maximum Clock Frequency
0.25
DC
2000
DC
0.1
ms
4000
kHz
6. This parameter is tested initially and after a design or process change that affects the parameter.
Table 8. INSTRUCTION SET
Address
Data
Instruction
Start
Bit
Opcode
x8
x16
READ
1
10
A10−A0
A9−A0
ERASE
1
11
A10−A0
A9−A0
WRITE
1
01
A10−A0
A9−A0
EWEN
1
00
11XXXXXXXXX
11XXXXXXXX
Write Enable
EWDS
1
00
00XXXXXXXXX
00XXXXXXXX
Write Disable
ERAL*
1
00
10XXXXXXXXX
10XXXXXXXX
Clear All Addresses
WRAL*
1
00
01XXXXXXXXX
01XXXXXXXX
*Not available at VCC < 1.8 V
http://onsemi.com
3
x8
x16
Comments
Read Address AN– A0
Clear Address AN– A0
D7−D0
D7−D0
D15−D0
D15−D0
Write Address AN– A0
Write All Addresses
CAT93C86B
Device Operation
The CAT93C86B is a 16,384−bit nonvolatile memory
intended for use with industry standard microprocessors.
The CAT93C86B can be organized as either registers of 16
bits or 8 bits. When organized as X16, seven 13−bit
instructions control the reading, writing and erase
operations of the device. When organized as X8, seven
14−bit instructions control the reading, writing and erase
operations of the device. The CAT93C86B operates on a
single power supply and will generate on chip, the high
voltage required during any write operation.
Instructions, addresses, and write data are clocked into the
DI pin on the rising edge of the clock (SK). The DO pin is
normally in a high impedance state except when reading data
from the device, or when checking the ready/busy status
after a write operation.
The ready/busy status can be determined after the start of
a write operation by selecting the device (CS high) and
polling the DO pin; DO low indicates that the write
operation is not completed, while DO high indicates that the
device is ready for the next instruction. If necessary, the DO
pin may be placed back into a high impedance state during
chip select by shifting a dummy “1” into the DI pin. The DO
pin will enter the high impedance state on the falling edge of
the clock (SK). Placing the DO pin into the high impedance
state is recommended in applications where the DI pin and
the DO pin are to be tied together to form a common DI/O
pin.
The format for all instructions sent to the device is a
logical “1” start bit, a 2−bit (or 4−bit) opcode, 10−bit address
(an additional bit when organized X8) and for write
operations a 16−bit data field (8−bit for X8 organizations).
Note: The Write, Erase, Write all and Erase all instructions
require PE = 1. If PE is left floating, 93C86B is in Program
Enabled mode. For Write Enable and Write Disable
instruction PE = don’t care.
Read
Upon receiving a READ command and an address
(clocked into the DI pin), the DO pin of the CAT93C86B will
come out of the high impedance state and, after sending an
initial dummy zero bit, will begin shifting out the data
addressed (MSB first). The output data bits will toggle on
the rising edge of the SK clock and are stable after the
specified time delay (tPD0 or tPD1).
After the initial data word has been shifted out and CS
remains asserted with the SK clock continuing to toggle, the
device will automatically increment to the next address and
shift out the next data word in a sequential READ mode. As
long as CS is continuously asserted and SK continues to
toggle, the device will keep incrementing to the next address
automatically until it reaches to the end of the address space,
then loops back to address 0. In the sequential READ mode,
only the initial data word is preceeded by a dummy zero bit.
All subsequent data words will follow without a dummy
zero bit.
Write
After receiving a WRITE command, address and the data,
the CS (Chip Select) pin must be deselected for a minimum
of tCSMIN. The falling edge of CS will start the self clocking
clear and data store cycle of the memory location specified
in the instruction. The clocking of the SK pin is not
necessary after the device has entered the self clocking
mode. The ready/busy status of the CAT93C86B can be
determined by selecting the device and polling the DO pin.
Since this device features Auto−Clear before write, it is
NOT necessary to erase a memory location before it is
written into.
http://onsemi.com
4
CAT93C86B
tSKHI
tSKLOW
tCSH
SK
tDIS
tDIH
VALID
DI
VALID
tCSS
CS
tPD0, tPD1
tDIS
DO
tCSMIN
DATA VALID
Figure 2. Synchronous Data Timing
SK
1
1
1
1
1
AN
AN−1
1
1
1
1
1
1
1
1
1
1
CS
DI
1
1
Don’t Care
A0
0
HIGH−Z
DO
Dummy 0
D15 . . . D0
or
D7 . . . D0
Address + 1
D15 . . . D0
or
D7 . . . D0
Address + 2
D15 . . . D0
or
D7 . . . D0
Address + n
D15 . . .
or
D7 . . .
Figure 3. Read Instruction Timing
SK
tCSMIN
CS
AN AN−1
DI
DO
1
0
A0
DN
STATUS
VERIFY
D0
STANDBY
1
tSV
HIGH−Z
BUSY
READY
tEW
Figure 4. Write Instruction Timing
http://onsemi.com
5
tHZ
HIGH−Z
CAT93C86B
Erase
Erase All
Upon receiving an ERASE command and address, the CS
(Chip Select) pin must be deasserted for a minimum of
tCSMIN. The falling edge of CS will start the self clocking
clear cycle of the selected memory location. The clocking of
the SK pin is not necessary after the device has entered the
self clocking mode. The ready/busy status of the
CAT93C86B can be determined by selecting the device and
polling the DO pin. Once cleared, the content of a cleared
location returns to a logical “1” state.
Upon receiving an ERAL command, the CS (Chip Select)
pin must be deselected for a minimum of tCSMIN. The falling
edge of CS will start the self clocking clear cycle of all
memory locations in the device. The clocking of the SK pin
is not necessary after the device has entered the self clocking
mode. The ready/busy status of the CAT93C86B can be
determined by selecting the device and polling the DO pin.
Once cleared, the contents of all memory bits return to a
logical “1” state.
Erase/Write Enable and Disable
Write All
The CAT93C86B powers up in the write disable state.
Any writing after power−up or after an EWDS (write
disable) instruction must first be preceded by the EWEN
(write enable) instruction. Once the write instruction is
enabled, it will remain enabled until power to the device is
removed, or the EWDS instruction is sent. The EWDS
instruction can be used to disable all CAT93C86B write and
clear instructions, and will prevent any accidental writing or
clearing of the device. Data can be read normally from the
device regardless of the write enable/disable status.
Upon receiving a WRAL command and data, the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN. The falling edge of CS will start the self clocking
data write to all memory locations in the device. The
clocking of the SK pin is not necessary after the device has
entered the self clocking mode. The ready/busy status of the
CAT93C86B can be determined by selecting the device and
polling the DO pin. It is not necessary for all memory
locations to be cleared before the WRAL command is
executed.
SK
CS
AN
DI
DO
1
1
AN−1
A0
tCS
STATUS
VERIFY
STANDBY
1
tSV
HIGH−Z
BUSY
tEW
Figure 5. Erase Instruction Timing
http://onsemi.com
6
tHZ
READY
HIGH−Z
CAT93C86B
PACKAGE DIMENSIONS
PDIP−8, 300 mils
CASE 646AA−01
ISSUE A
SYMBOL
MIN
NOM
A
E1
5.33
A1
0.38
A2
2.92
3.30
4.95
b
0.36
0.46
0.56
b2
1.14
1.52
1.78
c
0.20
0.25
0.36
D
9.02
9.27
10.16
E
7.62
7.87
8.25
E1
6.10
6.35
7.11
e
PIN # 1
IDENTIFICATION
MAX
2.54 BSC
eB
7.87
L
2.92
10.92
3.30
3.80
D
TOP VIEW
E
A2
A
A1
c
b2
L
e
eB
b
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MS-001.
http://onsemi.com
7
CAT93C86B
PACKAGE DIMENSIONS
SOIC 8, 150 mils
CASE 751BD−01
ISSUE O
E1
E
SYMBOL
MIN
A
1.35
1.75
A1
0.10
0.25
b
0.33
0.51
c
0.19
0.25
D
4.80
5.00
E
5.80
6.20
E1
3.80
MAX
4.00
1.27 BSC
e
PIN # 1
IDENTIFICATION
NOM
h
0.25
0.50
L
0.40
1.27
θ
0º
8º
TOP VIEW
D
h
A1
θ
A
c
e
b
L
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-012.
http://onsemi.com
8
CAT93C86B
PACKAGE DIMENSIONS
SOIC−8, 208 mils
CASE 751BE−01
ISSUE O
SYMBOL
MIN
NOM
2.03
A
E1 E
MAX
A1
0.05
0.25
b
0.36
0.48
c
0.19
0.25
D
5.13
5.33
E
7.75
8.26
E1
5.13
5.38
1.27 BSC
e
L
0.51
0.76
θ
0º
8º
PIN#1 IDENTIFICATION
TOP VIEW
D
A
e
b
q
L
A1
SIDE VIEW
c
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with EIAJ EDR-7320.
http://onsemi.com
9
CAT93C86B
PACKAGE DIMENSIONS
TSSOP8, 4.4x3
CASE 948AL−01
ISSUE O
b
SYMBOL
MIN
NOM
E1
E
MAX
1.20
A
A1
0.05
A2
0.80
b
0.19
0.30
c
0.09
0.20
D
2.90
3.00
3.10
E
6.30
6.40
6.50
E1
4.30
4.40
4.50
0.15
0.90
e
0.65 BSC
L
1.00 REF
L1
0.50
θ
0º
0.60
1.05
0.75
8º
e
TOP VIEW
D
A2
c
q1
A
A1
L1
SIDE VIEW
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
http://onsemi.com
10
CAT93C86B
PACKAGE DIMENSIONS
UDFN8, 2x3 EXTENDED PAD
CASE 517AZ−01
ISSUE O
D
b
A
e
L
DAP SIZE 1.8 x 1.8
E2
E
PIN #1
IDENTIFICATION
A1
PIN #1 INDEX AREA
D2
TOP VIEW
SIDE VIEW
SYMBOL
MIN
NOM
MAX
A
0.45
0.50
0.55
A1
0.00
0.02
0.05
A3
0.127 REF
b
0.20
0.25
0.30
D
1.95
2.00
2.05
D2
1.35
1.40
1.45
E
2.95
3.00
3.05
E2
1.25
1.30
1.35
e
L
BOTTOM VIEW
DETAIL A
0.065 REF
A3 A
FRONT VIEW
0.50 REF
0.25
0.30
0.35
A3
Notes:
(1) All dimensions are in millimeters.
(2) Refer JEDEC MO-236/MO-252.
0.0 - 0.05
DETAIL A
http://onsemi.com
11
0.065 REF
Copper Exposed
CAT93C86B
PACKAGE DIMENSIONS
MSOP 8, 3x3
CASE 846AD−01
ISSUE O
MIN
NOM
A1
0.05
0.10
0.15
A2
0.75
0.85
0.95
b
0.22
0.38
c
0.13
0.23
D
2.90
3.00
3.10
E
4.80
4.90
5.00
E1
2.90
3.00
3.10
SYMBOL
MAX
1.10
A
E
E1
0.65 BSC
e
L
0.60
0.40
0.80
L1
0.95 REF
L2
0.25 BSC
θ
0º
6º
TOP VIEW
D
A
A2
A1
DETAIL A
e
b
c
SIDE VIEW
END VIEW
q
L2
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-187.
L
L1
DETAIL A
http://onsemi.com
12
CAT93C86B
PACKAGE DIMENSIONS
WLCSP 6, 0.96 x 1.17
CASE TBD
ISSUE O
http://onsemi.com
13
CAT93C86B
ORDERING INFORMATION
Specific Device
Marking
Package Type
Temperature Range
Lead
Finish
Shipping
CAT93C86BLI−G
93C86D
PDIP−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tube, 50 Units / Tube
CAT93C86BLE−G
93C86D
PDIP−8
E = Extended
(−40°C to +125°C)
NiPdAu
Tube, 50 Units / Tube
CAT93C86BVI−GT3
93C86D
SOIC−8, JEDEC
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BVI−GT3L
93C86D
SOIC−8, JEDEC
I = Industrial
−20°C to +85°C
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BVE−GT3
93C86D
SOIC−8, JEDEC
E = Extended
(−40°C to +125°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BYI−GT3
M86D
TSSOP−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BYI−GT3L
M86D
TSSOP−8
I = Industrial
(−20°C to +85°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BYE−GT3
M86D
TSSOP−8
E = Extended
(−40°C to +125°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BHU4I−GT3
M4U
UDFN−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BHU4E−GT3
M4U
UDFN−8
E = Extended
(−40°C to +125°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BC6ATR
(Note 9)
M4
WLCSP−6
I = Industrial
(−40°C to +85°C)
SnAgCu
Tape & Reel,
5,000 Units / Reel
CAT93C86BZI−GT3
M4
MSOP−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BZE−GT3
M4
MSOP−8
E = Extended
(−40°C to +125°C)
NiPdAu
Tape & Reel,
3,000 Units / Reel
CAT93C86BXI−T2
93C86D
SOIC−8, EIAJ
I = Industrial
(−40°C to +85°C)
Matte−Tin
Tape & Reel,
2,000 Units / Reel
CAT93C86BXE−T2
93C86D
SOIC−8, EIAJ
E = Extended
(−40°C to +125°C)
Matte−Tin
Tape & Reel,
2,000 Units / Reel
Order Number
7. All packages are RoHS−compliant (Lead−free, Halogen−free).
8. The standard lead finish is NiPdAu.
9. Preliminary. Please contact factory for availability.
10. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office.
11. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
12. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
14
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT93C86B/D
Similar pages