DC-AC INVERTER UNIT CXA-0492 (5.1W SINGLE OUTPUT) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for single lamp. APPLICABLE LCD: Lamp Voltage 845 Vrms Lamp Current 6.0 mArms Lamp Start Up Voltage 2200 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open Lamp Detection Dimming Function TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -30°C ~ +80°C -30°C ~ +85°C 95 %RH max 100 x 22 x 8.5 mm Unit : mm Weight :20 (g) typ. Components No. 1 2 3 Note: Please use plastic screw in case of a non-insulating mounting base! Part Discription PCB Connector CN1 Connector CN2 Input side CN1: Pin No. Symbols Vin CN 1-1~2 GND CN 1-3~4 Vrm t CN 1-5 Vbr CN 1-6 Rbr CN 1-7 Vs t CN 1-8 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0871 SM02(8.0)B-BHS-1-TB Note t=1m m Molex or equal JST or equal Ratings 10.8 ~ 13.2 Vdc 0 ~ 0.4=OFF/2.5 ~ Vin=ON 0 ~ 2.5 Vdc 0 ~ 50 kΏ 0 / 5 Vdc Output side CN2: Pin No. Symbols VHIGH CN 2-1 N.C. CN 2-2 VLOW CN 2-3 Ratings 845 Vrm s (6.0m Arm s ) (GND) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0, 10th August 2007 DC-AC INVERTER UNIT CXA-0492 (5.1W SINGLE OUTPUT) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Parameters Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin1 Iin2 Iin3 F1 F2 Vopen Vs t Alarm Signal Note 1 : Symbols Vin (V) 12±1.2 12±1.2 12±1.2 12±1.2 12±1.2 12±1.2 12±1.2 10.8 12±1.2 12±1.2 Conditions Vbr(V) / Tu (°C) Rbr (kΩ) 0.0 / 0.0 -30 ~ +80 2.5 / 50 -30 ~ +80 0.0 / 0.0 -30 ~ +80 0.0 / 0.0 -30 ~ +80 0.0 / 0.0 -30 ~ +80 0.0 / 0.0 -30 ~ +80 2.5 / 50 -30 ~ +80 0.0 / 0.0 -30 ~ +80 0.0 / 0.0 -30 ~ +80 0.0 / 0.0 -30 ~ +80 Specification Min. Typ. Max. 5.5 1.6 TBD 230 2050 4.5 6.0 2.6 0.59 9 55 255 2200 5.1 6.5 3.6 1.25 1 30 TBD 280 5.5 - 0 0.5 Unit Note m Arm s m Arm s m Adc m Adc m Adc kHz Hz Vrm s V V Dut y 100% V rmt =5V V rmt=0 V V rmt =5V ; RL=∞ Please keep minimum of 3mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. TEST CIRCUIT : Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0, 10th August 2007