DC-AC INVERTER UNIT PS-M05D05-NJ4L-162(S) (6,5 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. Optimized for AUO: G065VN01 V.0 APPLICABLE LCD: 6.4 to 12 inches double lamp type Lamp Voltage 365 Vrms Lamp Current 5.0 mArms Lamp Start Up Voltage 1.500 Vrms (Vin : 5 Vdc) FEATURES : Remote ON/OFF Ext. PWM-Dimming Function RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity LxWxH 105 x 23 x 10 mm CN2 CN1 15 ± 0.3 22,5 ± 0.5 5 ± 0.5 DIMENSIONS : -20°C ~ +65°C -20°C ~ +85°C 95 %RH max 10.0MAX Unit : mm Weight :20 (g) typ. Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-SM3 Note t=1.6m m JST or equal 3 Connector CN2 1 SM04(4.0)B-BHS JST or equal Output side CN2 : Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 Symbols Vin GND Ext. PWM N.C. CN 1-5 Vrm t Ratings 5 Vdc 0 ~ 5 Vdc (L activ) Pin No. CN 2-1 CN2-2 CN2-3 Symbols VHIGH VHIGH N.C. Ratings 365 Vrm s (5m Arm s ) 365 Vrm s (5m Arm s ) CN 2-4 VLOW GND 0 / 5 Vdc (H activ) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.1 , 11th October 2010 DC-AC INVERTER UNIT PS-M05D05-NJ4L-162(S) (6,5 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen Note 1 : Vin (V) 5±0.05 5±0.5 5±0.5 5±0.5 4.75 Specification Min. Typ. Max. 4.5 4.0 60 1.400 5.0 5.0 1.2 70 1.500 5.5 6.0 1.7 80 - Unit Note m Arm s m Arm s Adc kHz Vrm s Dut y 100 % Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Remote ON/OFF (CN1-5) has priority and can not be used in combination with External PWM Dimming (CN1-3). When 'Ext. PWM' (CN1-3) is used 'Vrmt' (CN1-5) should not be connected. The external PWM frequency should be in a range of 100 ~ 500 Hz. For other frequency please request. The optimum is 250 Hz. Here you will normally not get a interference to the vertical sync. frequency. Note 2: Note 3: TEST CIRCUIT : Vin 5V Conditions Vrmt Tu (°C) (V) 5±0.25 -20 ~ +65 5±0.25 -20 ~ +65 5±0.25 -20 ~ +65 5±0.25 -20 ~ +65 5±0.25 -20 ~ +65 A F Iin SW 1 1000:1 PROBE F CN1-1 Vopen V ~ Operation of unit a Operation b Non operation SW3 V CN2-1 CN1-2 SW4 CN2-2 CN1-3 T1 RL2 RL1 Ext. PWM* 0/5V CL2 NC A Iout ~ CN1-4 2 Vrmt 2.5 Vdc ~ Vin b Iout1 SW5 a V CL1 A ~ SW1 CN1-5 CN2-4 *) Only active when Vrmt is 0 Vdc or floating Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.1 , 11th October 2010