CAPA880 Quick Manual VA1_03-30-2016

CAPA880 Series Quick Installation Guide
Installing Fan
 CPU board x1
 USB cable x1
 Audio cable x1
 Product information CD x1
 Quick installation guide x1
 COM cable x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Connectors
The processor needs specially designed heatsink and fan assembly to cool
down and ensure sufficient air flow inside your system. After applying
thermal grease on the processor and installing it on the socket, please
place heatsink and fan assembly on top of it. Match the four screws to the
fixing holes on the board. Then screw tightly the heatsink and CPU fan
assembly onto the board. Also make sure the fan cable is plugged to fan
connector (CN1).
Quick Start
CN2
The basic procedures required to power on CAPA880:
(1). Require power at minimum 5A. Ensure that power supply is
OFF before connecting to CAPA880 and that all necessary
peripheral devices are plugged properly.
(2). Ensure all of the jumpers are at default settings; especially
JP5 (1-2 close).
(3). Firmly install DDR3 memory modules into connector SODIMM1
until fully seated.
(4). Firmly insert power to ATX1.
(5). Install a momentary on/off button/switch onto CN2, pin 9 and
10.
(6). Turn on the power supply.
(7). Press the on/off button/switch to power on CAPA880
4
9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
Connector
Description
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN9
CN10 (Optional)
CN11
CN12
CN14
CN15
CN16
CN17
ATX1
BAT1
SATA1
SCN1
SCN2
SODIMM1
Fan Connector
Front Panel Connector
LVDS Connector
SATA Power Connector
Inverter Connector
COM1 Wafer Connector
Audio Connector
USB 2.0 Wafer Port 5 and 6
Digital I/O Connector
Power Connector
SMBus Connector
Ethernet Port 1 and Port 2
USB 3.0 Port 0 and 1
USB 2.0 Port 2 and 3
HDMI Connector
VGA Connector
ATX Power Connector
CMOS Battery Connector
Serial ATA Port
Full-size PCI-Express Mini Card Connector
ZIO Expansion Connector
DDR3 SO-DIMM Connector
9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
1
CAPA880 Intel® CoreTM Processor Family 3.5” Board
Checklist
Note:
Be careful not to over tighten
the screws as it can damage
the processor or the CPU
board.
Jumper Settings
Before applying power to the CAPA880, please make sure all of the
jumpers are in factory default positions.
Jumper
JP1
JP2
JP3
JP5
Description
Setting
LVDS +3.3V/+5V/+12V Voltage Selection
Default: +3.3V
COM1 Data/Power Selection CN6 Pin 1: DCD
CN6 Pin 8: RI
Default: RS-232 Data
3-5 Close
4-6 Close
Restore BIOS Optimal Defaults
Default: Normal Operation
Auto Power On
Default: Disable
5-6 Close
1-2 Close
1-2 Close
Note: Please refer to the CAPA880 series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.
Bottom View
Board Layout
Side View
Top View
2
9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
9418E880000E
©Copyright 2016 Axiomtek Co., Ltd.
Version A1 March 2016
Printed in Taiwan
3
Similar pages