REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED F Add peak current to absolute maximum ratings. Editorial changes throughout. 92-11-24 M. A. FRYE G Changes in accordance with NOR 5962-R144-95. 95-10-20 M. A. FRYE H Make corrections to the switch operation table in 3.3.1. Update boilerplate to reflect current requirements. -rrp 03-03-10 R. MONNIN J Make correction to marking paragraph 3.5. -rrp 05-05-11 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. CURRENT CAGE CODE 67268 REV SHEET REV SHEET REV STATUS REV J J J J J J J J J J J J OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY GARY J. ZAHN STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil CHECKED BY WILLIAM E. SHARP APPROVED BY N. A. HAUCK MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL ANALOG SWITCHES WITH DRIVERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 81-10-01 REVISION LEVEL J SIZE CAGE CODE A 14933 SHEET DSCC FORM 2233 APR 97 1 OF 81006 12 5962-E329-05 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 81006 01 X X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 Generic number Circuit function IH5040, DG5140 IH5041, DG5141 IH5042, DG5142 IH5043, DG5143 IH5044, DG5144 IH5045, DG5145 IH5046 IH5047 IH5140, HI5040 IH5141, HI5041 IH5142, HI5042 IH5143, HI5043 IH5144, HI5044 IH5145, HI5045 HI5046 IH5047, HI5047 HI5046A HI5047A IH5148, HI5048 IH5149, HI5049 IH5150, HI5050 IH5151, HI5051 One-channel, 75 ohms, SPST switch Two-channel, 75 ohms, SPST switch One-channel, 75 ohms, SPDT switch Two-channel, 75 ohms, SPDT switch One-channel, 75 ohms, DPST switch Two-channel, 75 ohms, DPST switch One-channel, 75 ohms, DPDT switch One-channel, 75 ohms, 4PST switch One-channel, 75 ohms, SPST switch Two-channel, 75 ohms, SPDT switch One-channel, 75 ohms, SPDT switch Two-channel, 30 ohms, SPDT switch One-channel, 30 ohms, DPST switch Two-channel, 75 ohms, DPST switch One-channel, 75 ohms, DPDT switch One-channel, 75 ohms, 4PST switch One-channel, 30 ohms, DPDT switch One-channel, 30 ohms, 4PST switch Two-channel, 30 ohms, SPST switch Two-channel, 30 ohms, DPST switch One-channel, 30 ohms, SPDT switch Two-channel, 30 ohms, SPDT switch 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter A E I 2 X Descriptive designator GDFP5-F14 or CDFP6-F14 GDIP1-T16 or CDIP2-T16 MACY1-X10 CQCC1-N20 CDFP3-F14 Terminals Package style 14 16 10 20 14 Flat pack Dual-in-line Can Square leadless chip carrier Flat pack 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 2 1.3 Absolute maximum ratings. V+ - V- .................................................................................... V+ - VD.................................................................................... VD - V-..................................................................................... VD - VS .................................................................................... VL - V- ..................................................................................... VL - VIN .................................................................................... VL - VR .................................................................................... VIN - VR ................................................................................... VR - V-..................................................................................... VR - VIN ................................................................................... Current (any terminal except S or D) ...................................... Peak current (source to drain) .............................................. Storage temperature range..................................................... Lead temperature (soldering, 10 seconds) ............................. Junction temperature (TJ) ....................................................... Power dissipation, (PD): 2/ Cases A and X at TA = +125°C ........................................... Case E at TA = +125°C ....................................................... Case I at TA = +125°C ........................................................ Case 2 at TA = +125°C ....................................................... 33 V dc 30 V dc 30 V dc ±22 V dc 33 V dc 30 V dc 20 V dc 20 V dc 33 V dc 2 V dc 30 mA 80 mA 1/ -65°C to +150°C +300°C +175°C 350 mW 400 mW 350 mW 350 mW 1.4 Recommended operating conditions. +VCC ...................................................................................... -VCC ....................................................................................... VR .......................................................................................... VL ........................................................................................... +15 V dc -15 V dc 0 V dc 5 V dc Ambient operating temperature range (TA) ............................. -55°C to +125°C Thermal resistance, junction-to-case (θJC).............................. See MIL-STD-1835 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. 1/ Pulse at 1 ms, 10 percent duty cycle maximum. 2/ For TA = +100°C to +125°C, derate linearly at 12 mW/°C. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 3 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q” or “QML” certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.3.1 Switch operation. The analog switches listed below are guaranteed to turn “on” with either a “low” input (VR ≤ VIL ≤ 0.8 V) or “high” input (2.4 V ≤ VIH ≤ VIL) as specified below (see figure 1). Device types 01, 09 02, 10, 05, 13, 19 03, 11, 21 04, 12, 22 07, 15, 17 06, 08, 14, 16, 18, 20 VIN 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc Channels ON 1 Channels OFF 1 1, 2 1, 2 2 1 3, 4 1, 2 1, 4 2, 3 1 2 1, 2 3, 4 2, 3 1, 4 1, 2, 3, 4 1, 2, 3, 4 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer’s PIN may also be marked. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q” or “QML” certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55°C ≤ TA ≤ +125°C VCC = ±15 V unless otherwise specified RDS VD = -10 V, IS = 10 mA, Group A subgroups Device type 1, 3 1 - 16 Limits Min Drain source “ON” resistance 2 1, 3 1, 3 17 - 22 45 50 1 - 16 75 2 1, 3 150 17 - 22 45 All 75 2 VD = -7.5 V, IS = 10 mA, VCC = ±10 V 1, 3 2/ VD = 7.5 V, IS = -10 mA, VCC = ±10 V Channel “ON” leakage current Drain “OFF” leakage current Source “OFF” leakage current ID(ON) ID(OFF) IS(OFF) Input current, input voltage low IIL Input current, input voltage high IIH Positive supply current +ICC 2/ 50 2 150 1, 3 75 2 VS = VD = 10 V, See 3.3.1 for VIN 2, 3 VS = VD = -10 V, See 3.3.1 for VIN 2, 3 VS = -10 V, VD = 10 V, See 3.3.1 for VIN 2, 3 VS = 10 V, VD = -10 V, See 3.3.1 for VIN 2, 3 VS = 10 V, VD = -10 V, See 3.3.1 for VIN 2, 3 VS = -10 V, VD = 10 V, See 3.3.1 for VIN 2, 3 VIN = 0 V 1, 3 150 All -200 1 1 All 1 1 All 1 1 All 2 VIN = 2.4 V, 5 V 1, 3 All 2 VIN = 0 V, 5 V 1, 3 -2 2 200 -2 2 -100 100 -1 1 -100 100 -1 1 -100 100 -1 1 -100 100 -1 1 -1 1 -10 1 -ICC VIN = 0 V, 5 V 1, 3 10 10 nA µA 100 9 - 22 200 300 1-8 2 1 nA µA 1 -1 1-8 nA µA -1 2, 3 Negative supply current 200 -200 2 1 Ω 1/ 150 2 VD = 10 V, IS = -10 mA, Max 75 Unit µA -10 -100 9 - 22 2, 3 -200 -300 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 5 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions -55°C ≤ TA ≤ +125°C VCC = ±15 V unless otherwise specified +IL VIN = 0 V, 5 V Group A subgroups Device type 1, 3 1-8 Limits Min Logic supply current 2 1 +IR VIN = 0 V, 5 V 1, 3 9 - 22 -200 -300 1-8 2 1 11 tON 9 - 22 -200 -300 375 1-8 9 450 10 550 11 9 - 22 500 10 11 tOFF 800 250 1-8 9 250 10 400 11 9 - 22 450 10 VISO RL = 100 Ω, f = 100 kHz, VIN = 2 VP-P, CL = 5 pF, ns 350 9 Single channel isolation 2/ ns 450 9 Turn-off time µA -10 -100 2, 3 Turn-on time µA 100 2, 3 Reference supply current Max 10 Unit 600 9 All 60 dB 9 All 60 dB 9 All TA = +25°C Crosstalk between channels 2/ VCT Charge transfer error VCTE RL = 100 Ω, f = 100 kHz, VIN = 2 VP-P, CL = 5 pF, TA = +25°C 2/ VIN = 0 V, CL = 10 nF, 30 mV TA = +25°C Break before make time delay 2/ tD TA = +25°C 9 03, 04, 07 Driver input capacitance 2/ CA VIN = 0 V, TA = +25°C 9 All 45 pF Switch input capacitance 2/ Switch output capacitance 2 CIS Switch off, TA = +25°C 9 All 60 pF COS Switch off, TA = +25°C 9 All 60 pF 5 ns 1/ The listed resistance limits correspond to the following voltage values: 45 Ω and 75 Ω − ±9.25 V, ±6.75 V 50 Ω and 150 Ω - ±8.50 V, ±6.0 V 2/ If not tested, shall be guaranteed to the limits specified in table I herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 6 Device type 01 Device types 01 and 09 Device type 09 only Case outline A Case outline E Case outline I Device type 02 Device types 02 and 10 Device type 19 Case outline A Case outline E Case outline E FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 7 Device types 02 and 10 Case outline I Device type 03 Device types 03, 11, and 21 Case outline A Device type 04 Case outline E Device types 04, 12, and 22 Case outline A Case outline E Case outline 2 FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 8 Device types 05 and 13 Device type 05 Case outline A Case outline E Device type 06 Case outline I Device types 06, 14, and 20 Case outline A and X Case outline E Case outline 2 FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 9 Device types 07, 15, and 17 Device type 07 Case outline A Case outline E Device type 08 Device types 08, 16, and 18 Case outline A Case outline E FIGURE 1. Terminal connections – Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 10 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer’s product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125°C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 11 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) * PDA applies to subgroup 1. Subgroups (in accordance with MIL-STD-883, method 5005, table I) ---1*, 2, 3 1, 2, 3, 9, 10, 11 1 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125°C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 81006 A REVISION LEVEL J SHEET 12 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 05-05-11 Approved sources of supply for SMD 81006 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/ . Standard microcircuit drawing PIN 1/ Vendor CAGE number 8100601AA 3/ 8100601EA 1ES66 Vendor similar PIN 2/ Reference military specification PIN IH5040MFD M38510/10501BAA IH5040MJE/883B M38510/10501BEA 3/ DG5140AK 8100602AA 3/ IH5041MFD M38510/10502BAA 8100602EA 1ES66 IH5041MJE/883B M38510/10502BEA 3/ DG5141AK 8100602IA 3/ DG5141AA M38510/10502BIA 8100603AA 3/ IH5042MFD M38510/10503BAA 8100603EA 1ES66 IH5042MJE/883B M38510/10503BEA 3/ DG5142AK 8100604AA 3/ IH5043MFD M38510/10504BAA 8100604EA 3/ IH5043MJE M38510/10504BEA 1ES66 IH5043MJE/883B 3/ DG5143AK 8100605AA 3/ IH5044MFD M38510/10505BAA 8100605EA 1ES66 IH5044MJE/883B M38510/10505BEA 3/ DG5144AK 8100605IA 3/ DG5144AA M38510/10505BIA 8100606AA 3/ IH5045MFD/883B M38510/10506BAA 8100606EA 1ES66 IH5045MJE/883B M38510/10506BEA 3/ DG5145AK 8100606XC 1ES66 8100607AA 3/ IH5046MFD 8100607EA 3/ IH5046MJE M38510/10507BEA 8100608AA 3/ IH5047MFD M38510/10508BAA 8100608EA 1ES66 IH5047MJE/883B M38510/10508BEA 8100609EA 1ES66 IH5140MJE/883B M38510/10501BEA 8100609IA IH5045MFD/883B 3/ HI1-5040/883 3/ DG5040AA See footnotes at end of table. 1 of 3 M38510/10507BAA M38510/10501BIA STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued. Standard microcircuit drawing PIN 1/ 8100610EA 8100610IA 8100611EA 8100612EA Vendor CAGE number 1ES66 Vendor similar PIN 2/ IH5141MJE/883B Reference military specification PIN M38510/10502BEA 3/ IH5141MJE 3/ HI1-5041/883 3/ DG5041AA M38510/10502BIA IH5142MJE/883B M38510/10503BEA 1ES66 3/ IH5142MJE 3/ HI1-5042/883 1ES66 IH5143MJE/883B 3/ IH5143MJE 3/ HI1-5043/883 81006122A 34371 HI4-5043/883 8100613EA 1ES66 IH5144MJE/883B M38510/10504BEA --M38510/10505BEA 3/ IH5144MJE 3/ HI1-5044/883 8100613IA 3/ DG5044AA M38510/10505BIA 8100614EA 1ES66 IH5145MJE/883B M38510/10506BEA 3/ IH5145MJE 3/ HI1-5045/883 81006142A 3/ HI4-5045/883 8100615EA 3/ HI1-5046/883 M38510/10507BEA 8100616EA 1ES66 IH5047MJE/883B M38510/10508BEA 3/ 8100617EA 34371 --- HI1-5047/883 HI1-5046A/883 --- 8100618EA 3/ HI1-5047A/883 --- 8100619EA 3/ IH5148MJE/883B --- 3/ HI1-5048/883 See footnotes at end of table. 2 of 3 STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued. Standard microcircuit drawing PIN 1/ 8100620EA Reference military specification Vendor CAGE number Vendor similar PIN 2/ 1ES66 IH5149MJE/883B PIN --- 3/ HI1-5049/883 81006202A 3/ HI4-5049/883 --- 8100621EA 1ES66 IH5150MJE/883B --- 8100622EA 3/ HI1-5050/883 3/ IH5151MJE 3/ HI1-5051/883 1ES66 81006222A 3/ --- IH5151MJE/883B HI4-5051/883 --- 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number Vendor name and address 1ES66 Maxim Integrated Products 120 San Gabriel Drive Sunnyvale, CA 94086 34371 Intersil Corporation 2401 Palm Bay Blvd P.O. Box 883 Melbourne, FL 32902-0883 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 3 of 3