8 7 6 5 4 3 2 STAINLESS STEEL COMPATIBLE LASER WELDABLE 50 OHM FEEDTHROUGH SMPM ADAPTABLE, .012 DIAMETER CENTER CONTACT, PRESS-IN D SRIFT1022 DOCUMENT REVISIONS REV CHANGE NO. DATE - INIT RLSE 2012-09-25 RELEASE APPROVAL • CONFIGURATION FOR INTERFACING TO SMPM "BULLET" STYLE ADAPTER • DESIGNED TO LASER WELD INTO AN ELECTRONIC CHASSIS D • INDUSTRY STANDARD NICKEL-IRON-COBALT ALLOY CONTACT WITH CORNING 7070 EQUIVALENT GLASS • INTEGRAL RF GROUNDING TAB FOR EXCELLENT PERFORMANCE OVER TEMPERATURE 1. LEAK RATE: LESS THAN OR EQUAL TO 1X10E-9 CC/SEC He AT ONE ATMOSPHERE DIFFERENTIAL PRESSURE. 2. NOMINAL IMPEDANCE: 50 OHMS 3. INTERFACE IN ACCORDANCE WITH MIL-STD-348, SMPM. 4. MATERIALS: PIN: NICKEL-IRON-COBALT ALLOY IN ACCORDANCE WITH ASTM F15. DIELECTRIC: CORNING 7070 EQUIVALENT GLASS (MATCHED SEAL). SHELL (WELD FLANGE): STAINLESS STEEL ALLOY 17-4PH IN ACCORDANCE WITH ASTM A564, TYPE 630. RF GROUNDING SPRING: BERYLLIUM-COPPER ALLOY 172/173 IN ACCORDANCE WITH ASTM B194 (NICKEL/GOLD PLATE). C 5. FINISH: FERRULE AND PIN: NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488, TYPE III, CODE A, .000050/.000100 THICK. C GROUNDING SPRING: NICKEL PLATE PER QQ-N-290, CLASS 2, .000100/.000250 THICK GOLD PLATE PER ASTM B488, TYPE III, CODE A, .000030/.000050 THICK. 6. ORDERING INSTRUCTIONS: SPECIFY BASE NUMBER FOLLOWED BY DASH NUMBER INDICATING DETENT TYPE, PIN EXTENSION AND DIELECTRIC APPLICATION TYPE: EXAMPLE: SRIFT1022 - FD 130 A DIELECTRIC APPLICATION TYPE (A-AIR, T-TEFLON) PIN EXTENSION (L) DETENT TYPE (FD -FULL, SB - SMOOTH) BASE NUMBER B B VIEWS SHOWN WITHOUT GROUNDING SPRING UNLESS OTHERWISE SPECIFIED A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH THIRD ANGLE PROJECTION SRI HERMETICS TITLE FEEDTHROUGH, SMPM COMPATIBLE, STAINLESS STEEL LASER WELDABLE SIZE DOCUMENT A SCALE FORM 300067 REV - 7 6 5 4 3 (321) 254-4067 WWW.SRIHERMETICS.COM 8:1 2 CAGE CODE SRIFT1022 3PJY7 SHEET 1 REV - 1 OF 2 A 8 6 7 4 5 3 2 SRIFT1022 DOCUMENT .140 D L±.003 D .151 MAX OVER KNURL .012±.001 DETENT PIN .057±.002 FERRULE WELD FLANGE INSTALL THIS DIRECTION STRAIGHT KNURL VIEW SHOWN WITHOUT RF GROUNDING SPRING SHELL C C .135±.002 8X 45° .028 (AIR DIELECTRIC APPLICATION) .040 (TEFLON DIELECTRIC APPLICATION) .028 .001 THRU (AIR DIELECTRIC) .039 .001 SHOWN (PTFE DIELECTRIC) .053 .002 X 90 (PTFE DIELECTRIC ONLY) .138 .001 SHOWN .148 .001 SHOWN .0020±.0005 .134±.002 8X .008 .074±.002 B B AS REQUIRED .040 MIN ANNULAR RING REQUIRED FOR LASER WELD NO PLATING ALLOWED .003 MAX BRK O NO PLATING UNLESS OTHERWISE SPECIFIED A DIMENSIONING IAW ASME Y14.5M-1994 DIMENSIONS APPLY AFTER PROCESSES DIMENSIONS IAW US CUSTOMARY UNITS .X .1, .XX .01, .XXX .005, .5 .010 MAX OUTSIDE R, .005 MAX INSIDE R 125 RMS SURFACE FINISH THIRD ANGLE PROJECTION RECOMMENDED HOLE DETAIL FORM 300067 REV - 7 6 SRI HERMETICS TITLE FEEDTHROUGH, SMPM COMPATIBLE, STANLESS STEEL LASER WELDABLE SIZE DOCUMENT A SCALE 5 4 3 (321) 254-4067 WWW.SRIHERMETICS.COM 8:1 2 CAGE CODE SRIFT1022 3PJY7 SHEET 1 REV - 2 OF 2 A