Obsolete Device 28C04A 4K (512 x 8) CMOS EEPROM 32 Vcc 31 WE 29 A8 6 28 NC 7 27 NC 8 9 10 11 26 NC 25 OE 24 NC 23 CE 20 19 18 17 21 I/O6 15 22 I/O7 13 14 12 • Pin 1 indicator on PLCC on top of package BLOCK DIAGRAM I/O0 DESCRIPTION The Microchip Technology Inc. 28C04A is a CMOS 4K non-volatile electrically Erasable and Programmable Read Only Memory (EEPROM). The 28C04A is accessed like a static RAM for the read or write cycles without the need of external components. During a “byte write”, the address and data are latched internally, freeing the microprocessor address and data bus for other operations. Following the initiation of write cycle, the device will go to a busy state and automatically clear and write the latched data using an internal control timer. To determine when a write cycle is complete, the 28C04A uses Data polling. Data polling allows the user to read the location last written to when the write operation is complete. CMOS design and processing enables this part to be used in systems where reduced power consumption and reliability are required. A complete family of packages is offered to provide the utmost flexibility in applications. 2004 Microchip Technology Inc. Vcc A8 NC WE OE NC CE I/O7 I/O6 I/O5 I/O4 I/O3 5 28C04A A6 A5 A4 A3 A2 A1 A0 NC I/O0 2 NC 1 NU PLCC 24 23 22 21 20 19 18 17 16 15 14 13 30 NC •1 2 3 4 5 6 7 8 9 10 11 12 4 A7 3 NC A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 16 DIP 28C04A • Fast Read Access Time—150 ns • CMOS Technology for Low Power Dissipation - 30 mA Active - 100 µA Standby • Fast Byte Write Time—200 µs or 1 ms • Data Retention >200 years • Endurance - Minimum 104 Erase/Write Cycles - Automatic Write Operation - Internal Control Timer - Auto-Clear Before Write Operation - On-Chip Address and Data Latches • Data Polling • Chip Clear Operation • Enhanced Data Protection - VCC Detector - Pulse Filter - Write Inhibit • 5-Volt-Only Operation • Organized 512x8 JEDEC standard pinout - 24-pin Dual-In-Line Package - 32-pin PLCC Package • Available for Extended Temperature Ranges: - Commercial: 0°C to +70°C - Industrial: -40°C to +85°C PACKAGE TYPES I/O1 I/O2 Vss NU I/O3 I/O4 I/O5 FEATURES VSS VCC Data Protection Circuitry Chip Enable/ Output Enable Control Logic CE OE WE I/O7 Auto Erase/Write Timing Data Poll Input/Output Buffers Program Voltage Generation A0 L a t c h e s Y Decoder Y Gating X Decoder 4K bit Cell Matrix A8 DS11126H-page 1 28C04A 1.0 ELECTRICAL CHARACTERISTICS 1.1 MAXIMUM RATINGS* TABLE 1-1: PIN FUNCTION TABLE Name Function VCC and input voltages w.r.t. VSS ....... -0.6V to + 6.25V A0 - A8 Voltage on OE w.r.t. VSS...................... -0.6V to +13.5V CE Chip Enable OE Output Enable WE Write Enable Output Voltage w.r.t. VSS .................-0.6V to VCC+0.6V Storage temperature ..........................-65°C to +125°C Ambient temp. with power applied .......-50°C to +95°C *Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-2: Address Inputs I/O0 - I/O7 Data Inputs/Outputs VCC +5V Power Supply VSS Ground NC No Connect; No Internal Connection NU Not Used; No External Connection is Allowed READ/WRITE OPERATION DC CHARACTERISTICS VCC = +5V ±10% Commercial (C): Tamb = Industrial (I): Tamb = Parameter 0°C to +70°C -40°C to +85°C Status Symbol Min Max Units Logic ‘1’ Logic ‘0’ VIH VIL 2.0 -0.1 VCC+1 0.8 V V Input Leakage ILI -10 10 µA VIN = -0.1V to VCC+1 Input Capacitance CIN 10 pF VIN = 0V; Tamb = 25°C; f = 1 MHz 0.45 V V IOH = -400 µA IOL = 2.1 mA 10 µA VOUT = -0.1V TO VCC + 0.1V COUT 12 pF VIN = 0V; TAMB = 25°C; f = 1 MHz ICC 30 mA f = 5 MHz (Note 1) VCC = 5.5V 2 3 100 mA mA µA CE = VIH (0°C to +70°C) CE = VIH (-40°C to +85°C) CE = VCC-0.3 to VCC+1 OE = VCC All inputs equal VCC or VSS Input Voltages Output Voltages Logic ‘1’ Logic ‘0’ Output Leakage Output Capacitance Power Supply Current, Active Power Supply Current, Standby TTL input VOH VOL 2.4 ILO -10 TTL input ICC(S)TTL ICC(S)TTL TTL input CMOS input ICC(S)CMOS Conditions Note 1: AC power supply current above 5 MHz; 1 mA/MHz. DS11126H-page 2 2004 Microchip Technology Inc. 28C04A TABLE 1-3: READ OPERATION AC CHARACTERISTICS AC Testing Waveform: Output Load: Input Rise and Fall Times: Ambient Temperature: Parameter VIH = 2.4V; VIL = 0.45V; VOH = 2.0V; VOL = 0.8V 1 TTL Load + 100 pF 20 ns Commercial (C): Tamb = 0°C to +70°C Industrial (I): Tamb = -40°C to +85°C 28C04A-15 28C04A-20 28C04A-25 Min Min Min Sym Units Max Max Conditions Max Address to Output Delay tACC 150 200 250 ns OE = CE = VIL CE to Output Delay tCE 150 200 250 ns OE = VIL OE to Output Delay tOE 70 80 100 ns CE = VIL CE to OE High Output Float tOFF 0 70 ns Output Hold from Address, CE or OE, whichever occurs first tOH 0 Endurance — 1M 50 0 55 0 — 1M 0 0 — 1M ns — cycles 25°C, Vcc = 5.0V, Block Mode (Note) Note: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our BBS or website. FIGURE 1-1: READ WAVEFORMS 2004 Microchip Technology Inc. DS11126H-page 3 28C04A TABLE 1-4: BYTE WRITE AC CHARACTERISTICS AC Testing Waveform: Output Load: Input Rise/Fall Times: Ambient Temperature: Parameter VIH = 2.4V; VIL = 0.45V; VOH = 2.0V; VOL = 0.8V 1 TTL Load + 100 pF 20 nsec Commercial (C): Tamb= 0°C to 70°C Industrial (I): Tamb= -40°C to 85°C Symbol Min Max Units Remarks Address Set-Up Time tAS 10 ns Address Hold Time tAH 50 ns Data Set-Up Time tDS 50 ns Data Hold Time tDH 10 ns Write Pulse Width tWPL 100 ns Write Pulse High Time tWPH 50 ns OE Hold Time tOEH 10 ns OE Set-Up Time tOES 10 ns Data Valid Time tDV 1000 ns Note 2 Write Cycle Time (28C04A) tWC 1 ms 0.5 ms typical Write Cycle Time (28C04AF) tWC 200 µs 100 µs typical Note 1 Note 1: A write cycle can be initiated be CE or WE going low, whichever occurs last. The data is latched on the positive edge of CE or WE, whichever occurs first. 2: Data must be valid within 1000ns max. after a write cycle is initiated and must be stable at least until tDH after the positive edge of WE or CE, whichever occurs first. FIGURE 1-2: PROGRAMMING WAVEFORMS VIH Address VIL VIH t AS t AH t WPL CE, WE VIL t DV Data In t DS t DH VIH VIL t OES VIH OE VIL t OEH DS11126H-page 4 2004 Microchip Technology Inc. 28C04A FIGURE 1-3: DATA POLLING WAVEFORMS VIH Last Written Address Valid Address Valid Address VIL t ACC VIH CE t CE VIL t WPH VIH t WPL WE VIL t OE VIH OE VIL t DV VIH Data In Valid Data VIL I/O7 Out True Data Out t WC FIGURE 1-4: CHIP CLEAR WAVEFORMS VIH CE VIL VH OE VIH tS tW tH VIH WE VIL 2004 Microchip Technology Inc. tW = 10ms tS = tH = 1µs VH = 12.0V ±0.5V DS11126H-page 5 28C04A 2.0 DEVICE OPERATION 2.4 The Microchip Technology Inc. 28C04A has four basic modes of operation—read, standby, write inhibit, and byte write—as outlined in the following table. Operation Mode CE IE WE I/O Read L L H DOUT Standby H X X High Z Write Inhibit H X X High Z Write Inhibit X L X High Z Write Inhibit X X H High Z Byte Write L H L DIN Byte Clear Automatic Before Each “Write” X = Any TTL level. 2.1 Read Mode The 28C04A has two control functions, both of which must be logically satisfied in order to obtain data at the outputs. Chip enable (CE) is the power control and should be used for device selection. Output Enable (OE) is the output control and is used to gate data to the output pins independent of device selection. Assuming that addresses are stable, address access time (tACC) is equal to the delay from CE to output (tCE). Data is available at the output tOE after the falling edge of OE, assuming that CE has been low and addresses have been stable for at least tACC-tOE. 2.2 Write Mode The 28C04A has a write cycle similar to that of a Static RAM. The write cycle is completely self-timed and initiated by a low going pulse on the WE pin. On the falling edge of WE, the address information is latched. On rising edge, the data and the control pins (CE and OE) are latched. 2.5 Data Polling The 28C04A features Data polling to signal the completion of a byte write cycle. During a write cycle, an attempted read of the last byte written results in the data complement of I/O7 (I/O0 to I/O6 are indeterminable). After completion of the write cycle, true data is available. Data polling allows a simple read/compare operation to determine the status of the chip eliminating the need for external hardware. 2.6 Chip Clear All data may be cleared to 1's in a chip clear cycle by raising OE to 12 volts and bringing the WE and CE low. This procedure clears all data. Standby Mode The 28C04A is placed in the standby mode by applying a high signal to the CE input. When in the standby mode, the outputs are in a high impedance state, independent of the OE input. 2.3 Data Protection In order to ensure data integrity, especially during critical power-up and power-down transitions, the following enhanced data protection circuits are incorporated: First, an internal VCC detect (3.3 volts typical) will inhibit the initiation of non-volatile programming operation when VCC is less than the VCC detect circuit trip. Second, there is a WE filtering circuit that prevents WE pulses of less than 10 ns duration from initiating a write cycle. Third, holding WE or CE high or OE low, inhibits a write cycle during power-on and power-off (VCC). DS11126H-page 6 2004 Microchip Technology Inc. 28C04A 28C04A Product Identification System To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed sales offices. 28C04A F T – 15 I /P Package: Temperature Range: Access Time: Blank = 0°C to +70°C I = -40°C to +85°C 15 20 25 150 ns 200 ns 250 ns Shipping: Blank T Option: Blank = twc = 1ms F = twc = 200 µs Device: 2004 Microchip Technology Inc. L = Plastic Leaded Chip Carrier (PLCC) P = Plastic DIP (600mill) 28C04A Tube Tape and Reel “L” only 512 x 8 CMOS EEPROM DS11126H-page 7 28C04A NOTES: DS11126H-page 8 2004 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, MXDEV, MXLAB, PICMASTER, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2004, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona and Mountain View, California in October 2003. The Company’s quality system processes and procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2004 Microchip Technology Inc. DS11126H-page 9 WORLDWIDE SALES AND SERVICE AMERICAS China - Beijing Singapore Corporate Office Unit 706B Wan Tai Bei Hai Bldg. No. 6 Chaoyangmen Bei Str. Beijing, 100027, China Tel: 86-10-85282100 Fax: 86-10-85282104 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: www.microchip.com China - Chengdu 3780 Mansell Road, Suite 130 Alpharetta, GA 30022 Tel: 770-640-0034 Fax: 770-640-0307 Rm. 2401-2402, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 Boston China - Fuzhou 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 Atlanta Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 16200 Addison Road, Suite 255 Addison Plaza Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, IN 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles 25950 Acero St., Suite 200 Mission Viejo, CA 92691 Tel: 949-462-9523 Fax: 949-462-9608 San Jose 1300 Terra Bella Avenue Mountain View, CA 94043 Tel: 650-215-1444 Fax: 650-961-0286 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 China - Hong Kong SAR Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Taiwan Kaohsiung Branch 30F - 1 No. 8 Min Chuan 2nd Road Kaohsiung 806, Taiwan Tel: 886-7-536-4816 Fax: 886-7-536-4817 Taiwan Taiwan Branch 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Taiwan Taiwan Branch 13F-3, No. 295, Sec. 2, Kung Fu Road Hsinchu City 300, Taiwan Tel: 886-3-572-9526 Fax: 886-3-572-6459 EUROPE China - Shanghai Austria Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Durisolstrasse 2 A-4600 Wels Austria Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 China - Shenzhen Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45-4420-9895 Fax: 45-4420-9910 Rm. 1812, 18/F, Building A, United Plaza No. 5022 Binhe Road, Futian District Shenzhen 518033, China Tel: 86-755-82901380 Fax: 86-755-8295-1393 China - Shunde Room 401, Hongjian Building, No. 2 Fengxiangnan Road, Ronggui Town, Shunde District, Foshan City, Guangdong 528303, China Tel: 86-757-28395507 Fax: 86-757-28395571 China - Qingdao Rm. B505A, Fullhope Plaza, No. 12 Hong Kong Central Rd. Qingdao 266071, China Tel: 86-532-5027355 Fax: 86-532-5027205 India Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-22290061 Fax: 91-80-22290062 Japan ASIA/PACIFIC Yusen Shin Yokohama Building 10F 3-17-2, Shin Yokohama, Kohoku-ku, Yokohama, Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Australia Korea Microchip Technology Australia Pty Ltd Unit 32 41 Rawson Street Epping 2121, NSW Sydney, Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Denmark France Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Steinheilstrasse 10 D-85737 Ismaning, Germany Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy Via Salvatore Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Waegenburghtplein 4 NL-5152 JR, Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/12/04 2004 Microchip Technology Inc.