24AA515 DATA SHEET (07/02/2008) DOWNLOAD

24AA515/24LC515/24FC515
512K I2C™ CMOS Serial EEPROM
Device Selection Table
Part
Number
VCC
Range
Max. Clock
Frequency
24AA515
1.8-5.5V
400 kHz†
I
24LC515
2.5-5.5V
400 kHz
I
24FC515
2.5-5.5V
1 MHz
I
Temp.
Ranges
†
100 kHz for VCC < 2.5V.
Reads may be sequential within address boundaries
0000h to 7FFFh and 8000h to FFFFh. Functional
address lines allow up to four devices on the same data
bus. This allows for up to 2 Mbits total system
EEPROM memory. This device is available in the
standard 8-pin plastic DIP and SOIJ packages.
Package Type
PDIP
Features:
A0
1
8
VCC
• Single Supply with Operation Down to 1.7V for
24AAXX Devices, 2.5V for 24LCXX Devices
• Low-Power CMOS Technology:
- Active current 500 uA, typical
- Standby current 100 nA, typical
• 2-Wire Serial Interface, I2C™ Compatible
• Cascadable up to Four Devices
• Schmitt Trigger Inputs for Noise Suppression
• Output Slope Control to Eliminate Ground Bounce
• 100 kHz and 400 kHz Clock Compatibility
• Page Write Time 5 ms max.
• Self-Timed Erase/Write Cycle
• 64-Byte Page Write Buffer
• Hardware Write Protect
• ESD Protection >4000V
• More than 1 Million Erase/Write Cycles
• Data Retention >200 years
• Factory Programming Available
• Packages Include 8-lead PDIP, SOIJ
• Pb-Free and RoHS Compliant
• Temperature Ranges:
- Industrial (I): -40°C to +85°C
- Automotive (E):-40°C to +125°C
A1
2
7
WP
A2
3
6
SCL
VSS
4
5
SDA
SOIJ
8
VCC
A1
2
7
WP
A2
3
6
SCL
VSS
4
5
SDA
A0A1
I/O
Control
Logic
WP
Memory
Control
Logic
HV Generator
XDEC
EEPROM
Array
Page Latches
I/O
© 2008 Microchip Technology Inc.
1
Block Diagram
SCL
Description:
The Microchip Technology Inc. 24AA515/24LC515/
24FC515 (24XX515*) is a 64K x 8 (512K bit) Serial
Electrically Erasable PROM, capable of operation
across a broad voltage range (1.7V to 5.5V). It has
been developed for advanced, low-power applications
such as personal communications or data acquisition.
This device has both byte write and page write capability of up to 64 bytes of data. This device is capable of
both random and sequential reads.
A0
YDEC
SDA
VCC
VSS
Sense AMP
R/W Control
*24XX515 is used in this document as a generic part number
for the 24AA515/24LC515/24FC515 devices.
DS21673G-page 1
24AA515/24LC515/24FC515
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
VCC .............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied ................................................................................................-40°C to +125°C
ESD protection on all pins ......................................................................................................................................................≥ 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
DC CHARACTERISTICS
Param.
No.
Sym.
Characteristic
Industrial (I): VCC = +1.7V to 5.5V TA = -40°C to +85°C
Min.
Max.
Units
Conditions
A0, A1, SCL, SDA and
WP pins:
D1
VIH
High-level input voltage
0.7 VCC
—
V
D2
VIL
Low-level input voltage
—
0.3 VCC
0.2 VCC
V
V
VCC ≥ 2.5V
VCC < 2.5V
D3
VHYS
Hysteresis of Schmitt
Trigger inputs
(SDA, SCL pins)
0.05 VCC
—
V
VCC ≥ 2.5V (Note)
D4
VOL
Low-level output voltage
—
0.40
V
IOL = 3.0 mA @ VCC = 4.5V
IOL = 2.1 mA @ VCC = 2.5V
D5
ILI
Input leakage current
—
±1
μA
VIN = VSS or VCC, WP = VSS
VIN = VSS or VCC, WP = VCC
D6
ILO
Output leakage current
—
±1
μA
VOUT = VSS or VCC
D7
CIN,
COUT
Pin capacitance
(all inputs/outputs)
—
10
pF
VCC = 5.0V (Note)
TA = 25°C, FCLK = 1 MHz
D8
ICC Read Operating current
—
500
μA
VCC = 5.5V, SCL = 400 kHz
—
3
mA
VCC = 5.5V
D9
Iccs
—
5
μA
SCL = SDA = VCC = 5.5V
A0, A1, WP = VSS, A2 = VCC
ICC Write
Note:
Standby current
This parameter is periodically sampled and not 100% tested.
DS21673G-page 2
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
TABLE 1-2:
AC CHARACTERISTICS
AC CHARACTERISTICS
Param.
No.
Sym.
Industrial (I):
Characteristic
VCC = +1.7V to 5.5V TA = -40°C to +85°C
Min.
Max.
Units
Conditions
1
FCLK
Clock frequency
—
—
—
100
400
1000
kHz
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
2
THIGH
Clock high time
4000
600
500
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
3
TLOW
Clock low time
4700
1300
500
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
4
TR
SDA and SCL rise time
(Note 1)
—
—
—
1000
300
300
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
5
TF
SDA and SCL fall time
(Note 1)
—
—
300
100
ns
All except, 24FC515
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
6
THD:STA Start condition hold time
4000
600
250
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
7
TSU:STA
4700
600
250
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
Start condition setup time
8
THD:DAT Data input hold time
9
TSU:DAT
10
0
—
ns
(Note 2)
250
100
100
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
TSU:STO Stop condition setup time
4000
600
250
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
11
TSU:WP
WP setup time
4000
600
600
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
12
THD:WP
WP hold time
4700
1300
1300
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
13
TAA
Output valid from clock
(Note 2)
—
—
—
3500
900
400
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
14
TBUF
Bus free time: Time the bus
must be free before a new
transmission can start
4700
1300
500
—
—
—
ns
1.7V ≤ VCC ≤ 2.5V
2.5V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24FC515 only)
15
TOF
Output fall time from VIH
minimum to VIL maximum
CB ≤ 100 pF
10 + 0.1CB
250
250
ns
All except, 24FC515 (Note 1)
24FC515 (Note 1)
16
TSP
Input filter spike suppression
(SDA and SCL pins)
—
50
ns
All except, 24FC515 (Notes 1 and 3)
17
TWC
Write cycle time (byte or page)
—
5
ms
1M
—
cycles
18
Data input setup time
Endurance
Note 1:
25°C (Note 4)
Not 100% tested. CB = total capacitance of one bus line in pF.
2:
As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum
300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3:
The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved noise spike
suppression. This eliminates the need for a TI specification for standard operation.
4:
This parameter is not tested but established by characterization. For endurance estimates in a specific application,
please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com.
© 2008 Microchip Technology Inc.
DS21673G-page 3
24AA515/24LC515/24FC515
FIGURE 1-1:
BUS TIMING DATA
5
SCL
7
SDA
IN
3
4
D4
2
8
10
9
6
16
14
13
SDA
OUT
WP
DS21673G-page 4
(protected)
(unprotected)
11
12
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
Function
A0
1
1
User Configurable Chip Select
A1
2
2
User Configurable Chip Select
A2
3
3
Non-Configurable Chip Select.
This pin must be hard wired to
logical 1 state (VCC). Device
will not operate with this pin
left floating or held to logical 0
(VSS).
4
4
Ground
SDA
5
5
Serial Data
SCL
6
6
Serial Clock
WP
7
7
Write-Protect Input
VCC
8
8
+1.7 to 5.5V (24AA515)
+2.5 to 5.5V (24LC515)
+2.5 to 5.5V (24FC515)
2.1
Serial Clock (SCL)
This input is used to synchronize the data transfer from
and to the device.
PIN FUNCTION TABLE
Name PDIP SOIJ
VSS
2.4
2.5
Write-Protect (WP)
This pin must be connected to either VSS or VCC. If tied
to VSS, write operations are enabled. If tied to VCC,
write operations are inhibited but read operations are
not affected.
3.0
FUNCTIONAL DESCRIPTION
The 24XX515 supports a bidirectional 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as a transmitter, and a device
receiving data as a receiver. The bus must be
controlled by a master device which generates the
Serial Clock (SCL), controls the bus access, and
generates the Start and Stop conditions while the
24XX515 works as a slave. Both master and slave can
operate as a transmitter or receiver, but the master
device determines which mode is activated.
A0, A1 Chip Address Inputs
The A0, A1 inputs are used by the 24XX515 for multiple
device operations. The levels on these inputs are
compared with the corresponding bits in the slave
address. The chip is selected if the compare is true.
Up to four devices may be connected to the same bus
by using different Chip Select bit combinations. In most
applications, the chip address inputs A0 and A1 are
hard-wired to logic ‘0’ or logic ‘1’. For applications in
which these pins are controlled by a microcontroller or
other programmable device, the chip address pins
must be driven to logic ‘0’ or logic ‘1’ before normal
device operation can proceed.
2.2
A2 Chip Address Input
The A2 input is non-configurable Chip Select. This pin
must be tied to VCC in order for this device to operate.
2.3
Serial Data (SDA)
This is a bidirectional pin used to transfer addresses
and data into and data out of the device. It is an opendrain terminal, therefore, the SDA bus requires a pullup resistor to VCC (typical 10 kΩ for 100 kHz, 2 kΩ for
400 kHz and 1 MHz).
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
© 2008 Microchip Technology Inc.
DS21673G-page 5
24AA515/24LC515/24FC515
4.0
BUS CHARACTERISTICS
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device.
4.5
Accordingly, the following bus conditions have been
defined (Figure 4-1).
4.1
Acknowledge
Each receiving device, when addressed, is obliged to
generate an Acknowledge signal after the reception of
each byte. The master device must generate an extra
clock pulse which is associated with this Acknowledge
bit.
Bus Not Busy (A)
Both data and clock lines remain high.
Note:
4.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
A device that acknowledges must pull down the SDA
line during the Acknowledge clock pulse in such a way
that the SDA line is stable low during the high period of
the acknowledge related clock pulse. Of course, setup
and hold times must be taken into account. During
reads, a master must signal an end of data to the slave
by NOT generating an Acknowledge bit on the last byte
that has been clocked out of the slave. In this case, the
slave (24XX515) will leave the data line high to enable
the master to generate the Stop condition.
Stop Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must end with a Stop condition.
4.4
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
FIGURE 4-1:
(A)
The 24XX515 does not generate any
Acknowledge bits if an internal programming cycle is in progress, however, the
control byte that is being polled must
match the control byte used to initiate the
write cycle.
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(B)
(D)
(D)
Start
Condition
Address or
Acknowledge
Valid
(C)
(A)
SCL
SDA
FIGURE 4-2:
Data
Allowed
to Change
Stop
Condition
ACKNOWLEDGE TIMING
Acknowledge
Bit
1
SCL
SDA
2
3
4
5
6
7
Data from transmitter
Transmitter must release the SDA line at this point
allowing the Receiver to pull the SDA line low to
acknowledge the previous eight bits of data.
DS21673G-page 6
8
9
1
2
3
Data from transmitter
Receiver must release the SDA line at this
point so the Transmitter can continue
sending data.
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
5.0
DEVICE ADDRESSING
FIGURE 5-1:
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a 4-bit control code; for the
24XX515, this is set as ‘1010’ binary for read and write
operations. The next bit of the control byte is the block
select bit (B0). This bit acts as the A15 address bit for
accessing the entire array. The next two bits of the
control byte are the Chip Select bits (A1, A0). The Chip
Select bits allow the use of up to four 24XX515 devices
on the same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
correspond to the logic levels on the corresponding A1
and A0 pins for the device to respond. These bits are in
effect the two Most Significant bits of the word address.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’, a read operation is
selected, and when set to a ‘0’, a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). Because
only A14…A0 are used, the upper address bit is a
“don’t care.” The upper address bits are transferred
first, followed by the Less Significant bits.
Following the Start condition, the 24XX515 monitors
the SDA bus checking the device type identifier being
transmitted. Upon receiving a ‘1010’ code and appropriate device select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24XX515 will select a read or
write operation.
CONTROL BYTE
FORMAT
Read/Write Bit
Block
Select
Bit
Control Code
S
1
0
1
0
B0
Chip
Select
Bits
A1
A0 R/W ACK
Slave Address
Start Bit
5.1
Acknowledge Bit
Contiguous Addressing Across
Multiple Devices
The Chip Select bits A1, A0 can be used to expand the
contiguous address space for up to 2 Mbit by adding up
to four 24XX515’s on the same bus. In this case,
software can use A0 of the control byte as address bit
A16 and A1 as address bit A17. It is not possible to
sequentially read across device boundaries.
Each device has internal addressing boundary
limitations. This divides each part into two segments of
256K bits. The block select bit ‘B0’ controls access to
each “half” rather than address bit location A15.
Sequential read operations are limited to 256K blocks.
To read through four devices on the same bus, eight
random Read commands must be given.
This device has an internal addressing boundary
limitation that is divided into two segments of 256K bits.
Block select bit ‘B0’ is used in place of address bit
location ‘A15’ to control access to each segment.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
Control Byte
1
0
1
Control
Code
0
B
0
Block
Select
Bit
A
1
Address High Byte
A
0 R/W
Chip
Select
Bits
© 2008 Microchip Technology Inc.
x
A A A A A
14 13 12 11 10
Address Low Byte
A
9
A
8
A
7
•
•
•
•
•
•
A
0
X = “don’t care” bit
DS21673G-page 7
24AA515/24LC515/24FC515
6.0
WRITE OPERATIONS
6.1
Byte Write
Following the Start condition from the master, the
control code (four bits), the block select (one bit) the
Chip Select (two bits), and the R/W bit (which is a logic
low) are clocked onto the bus by the master transmitter.
This indicates to the addressed slave receiver that the
address high byte will follow after it has generated an
Acknowledge bit during the ninth clock cycle. Therefore, the next byte transmitted by the master is the
high-order byte of the word address and will be written
into the Address Pointer of the 24XX515. The next byte
is the Least Significant Address Byte. After receiving
another Acknowledge signal from the 24XX515, the
master device will transmit the data word to be written
into the addressed memory location. The 24XX515
acknowledges again and the master generates a Stop
condition. This initiates the internal write cycle and
during this time, the 24XX515 will not generate
Acknowledge signals as long as the control byte being
polled matches the control byte that was used to initiate
the write (Figure 6-1). If an attempt is made to write to
the array with the WP pin held high, the device will
acknowledge the command but no write cycle will
occur, no data will be written, and the device will
immediately accept a new command. After a byte Write
command, the internal address counter will point to the
address location following the one that was just written.
6.2
6.3
Write Protection
The WP pin allows the user to write-protect the entire
array (0000-FFFF) when the pin is tied to VCC. If tied to
VSS the write protection is disabled. The WP pin is
sampled at the Stop bit for every Write command
(Figure 1-1) Toggling the WP pin after the Stop bit will
have no effect on the execution of the write cycle.
Note:
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes actually
being written. Physical page boundaries
start at addresses that are integer
multiples of the page buffer size (or ‘page
size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
Page Write
The write control byte, word address, and the first data
byte are transmitted to the 24XX515 in the same way
as in a byte write. But instead of generating a Stop
condition, the master transmits up to 63 additional
bytes, which are temporarily stored in the on-chip page
buffer and will be written into memory after the master
has transmitted a Stop condition. After receipt of each
word, the six lower Address Pointer bits are internally
incremented by one. If the master should transmit more
than 64 bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2). If an attempt
is made to write to the array with the WP pin held high,
the device will acknowledge the command but no write
cycle will occur, no data will be written, and the device
will immediately accept a new command.
DS21673G-page 8
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
FIGURE 6-1:
BYTE WRITE
S
T
A
R
T
Bus Activity
Master
Control
Byte
Address
High Byte
AA
S1 01 0B
0 10 0
SDA Line
Address
Low Byte
Data
x
P
A
C
K
Bus Activity
S
T
O
P
A
C
K
A
C
K
A
C
K
X = “don’t care” bit
FIGURE 6-2:
PAGE WRITE
Bus Activity
Master
S
T
A
R
T
SDA Line
BAA
S101 00 1 00
Control
Byte
Bus Activity
Address
High Byte
Address
Low Byte
Data Byte 0
S
T
O
P
Data Byte 63
P
x
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
X = “don’t care” bit
© 2008 Microchip Technology Inc.
DS21673G-page 9
24AA515/24LC515/24FC515
7.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete. (This feature can be used to maximize bus
throughput.) Once the Stop condition for a Write
command has been issued from the master, the device
initiates the internally timed write cycle. ACK polling
can be initiated immediately. This involves the master
sending a Start condition, followed by the control byte
for a Write command (R/W = 0). If the device is still
busy with the write cycle, then no ACK will be returned.
If no ACK is returned, then the Start bit and control byte
must be resent. If the cycle is complete, then the device
will return the ACK, and the master can then proceed
with the next Read or Write command. See Figure 7-1
for flow diagram.
Note:
Care must be taken when polling the
24LC515. The control byte that was used
to initiate the write needs to match the
control byte used for polling.
FIGURE 7-1:
ACKNOWLEDGE
POLLING FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)?
No
Yes
Next
Operation
DS21673G-page 10
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
8.0
READ OPERATION
8.2
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
control byte is set to one. There are three basic types
of read operations: current address read, random read
and sequential read.
8.1
Current Address Read
The 24XX515 contains an address counter that maintains the address of the last word accessed, internally
incremented by one. Therefore, if the previous read
access was to address n (n is any legal address), the
next current address read operation would access data
from address n + 1.
Upon receipt of the control byte with R/W bit set to one,
the 24XX515 issues an acknowledge and transmits the
8-bit data word. The master will not acknowledge the
transfer, but does generate a Stop condition and the
24XX515 discontinues transmission (Figure 8-1).
FIGURE 8-1:
CURRENT ADDRESS
READ
Bus Activity
Master
S
T
A
R
T
SDA Line
BAA 1
S 10 10 0
10
Control
Byte
Bus Activity
© 2008 Microchip Technology Inc.
S
T
O
P
Data
Byte
P
A
C
K
N
O
A
C
K
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24XX515 as part of a write operation (R/W bit set to 0).
After the word address is sent, the master generates a
Start condition following the acknowledge. This terminates the write operation, but not before the internal
Address Pointer is set. Then, the master issues the
control byte again, but with the R/W bit set to a one.
The 24XX515 will then issue an acknowledge and
transmit the 8-bit data word. The master will not
acknowledge the transfer, but does generate a Stop
condition which causes the 24XX515 to discontinue
transmission (Figure 8-2). After a random Read command, the internal address counter will point to the
address location following the one that was just read.
8.3
Sequential Read
Sequential reads are initiated in the same way as a
random read except that after the 24XX515 transmits
the first data byte, the master issues an acknowledge
as opposed to the Stop condition used in a random
read. This acknowledge directs the 24XX515 to transmit the next sequentially addressed 8-bit word
(Figure 8-3). Following the final byte transmitted to the
master, the master will NOT generate an acknowledge,
but will generate a Stop condition. To provide sequential reads, the 24XX515 contains an internal Address
Pointer which is incremented by one at the completion
of each operation. This Address Pointer allows half the
memory contents to be serially read during one operation. Sequential read address boundaries are 0000h to
7FFFh and 8000h to FFFFh. The internal Address
Pointer will automatically roll over from address 7FFF
to address 0000 if the master acknowledges the byte
received from the array address 7FFF. The internal
address counter will automatically roll over from
address FFFFh to address 8000h if the master
acknowledges the byte received from the array
address FFFFh.
DS21673G-page 11
24AA515/24LC515/24FC515
FIGURE 8-2:
Bus Activity
Master
SDA Line
RANDOM READ
S
T
A
R
T
Control
Byte
Address
High Byte
S 1 0 1 0 B A A0
0 1 0
Control
Byte
S
T
O
P
Data
Byte
S 1 0 1 0 B A A1
0 1 0
x
A
C
K
A
C
K
Bus Activity
S
T
A
R
T
Address
Low Byte
A
C
K
P
N
O
A
C
K
A
C
K
X = “don’t care” bit
FIGURE 8-3:
Bus Activity
Master
SEQUENTIAL READ
Control
Byte
Data n
Data n + 1
Data n + X
Data n + 2
S
T
O
P
P
SDA Line
Bus Activity
DS21673G-page 12
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
9.0
PACKAGING INFORMATION
9.1
Package Marking Information
8-Lead PDIP (300 mil)
24LC515
I/P e3 3L7
XXXXXXXX
T/XXXNNN
YYWW
0517
8-Lead SOIJ (5.28 mm)
XXXXXXXX
T/XXXXXX
YYWWNNN
Legend: XX...X
T
Y
YY
WW
NNN
e3
*
Example:
Example:
24LC515
I/SM e3
05173L7
Part number or part number code
Temperature (I, E)
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note:
For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Standard marking consists of Microchip part number, year code, week code, traceability code (facility
code, mask rev#, and assembly code). For marking beyond this, certain price adders apply. Please
check with your Microchip Sales Office.
© 2008 Microchip Technology Inc.
DS21673G-page 13
24AA515/24LC515/24FC515
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
N
NOTE 1
E1
1
3
2
D
E
A2
A
L
A1
c
e
eB
b1
b
6&!
'!
9'&!
7"')
%!
7,8.
7
7
7:
;
<
&
&
&
=
=
##44!!
-
1!&
&
=
=
"#&
"#>#&
.
-
-
##4>#&
.
<
: 9&
-<
-?
&
&
9
-
9#4!!
<
)
?
)
<
1
=
=
69#>#&
9
*9#>#&
: *+
1,
-
!"#$%&"' ()"&'"!&)
&#*&&&#
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#/!#
'!
#&
.0
1,21!'!
&$& "!
**&
"&&
!
* ,<1
DS21673G-page 14
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
!
""#$%& !'
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
N
E
E1
1
2
e
b
α
c
φ
A2
A
β
A1
6&!
'!
9'&!
7"')
%!
L
99..
7
7
7:
;
<
&
: 8&
1,
=
##44!!
=
<
&#
%%+
=
: >#&
.
?
=
<?
##4>#&
.
=
-<
: 9&
-
=
--
3
&9&
9
=
?
3
&
I
A
=
<A
9#4!!
=
9#>#&
)
-?
=
#%&
D
=
=
A
#%&1
&&
'
E
=
=
A
-
:@(@[email protected]&##(%
'#:,
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
* ,?1
© 2008 Microchip Technology Inc.
DS21673G-page 15
24AA515/24LC515/24FC515
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS21673G-page 16
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
APPENDIX A:
REVISION HISTORY
Revision C
Corrections to Section 1.0, Electrical Characteristics.
Revision D
Removed Preliminary status.
Revised conditions, Table 1-2, Param. 18.
Revision E
Revised Tables 1-1 and 2-1. Add Pb-free marking.
Revision F
Section 1.0 Electrical Characteristics: revised Ambient
Temperature; Revised Section 2.1 and Section 2.5
Revision G (07/2008)
Revised Features section; Revised 1.8V voltage to
1.7V; Replaced Package Drawings; Revised Product
ID System.
© 2008 Microchip Technology Inc.
DS21673G-page 17
24AA515/24LC515/24FC515
NOTES:
DS21673G-page 18
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
© 2008 Microchip Technology Inc.
DS21673G-page 19
24AA515/24LC515/24FC515
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: 24AA515/24LC515/24FC515
Literature Number: DS21673G
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS21673G-page 20
© 2008 Microchip Technology Inc.
24AA515/24LC515/24FC515
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
/XX
Temperature
Range
Package
Examples:
a)
b)
Device:
24AA515: =
24AA515T: =
24LC515: =
24LC515T: =
24FC515: =
24FC515T: =
512K Bit 1.8V I2C CMOS Serial EEPROM
512K Bit 1.8V I2C CMOS Serial EEPROM
(Tape and Reel)
512K Bit 2.5V I2C CMOS Serial EEPROM
512K Bit 2.5V I2C CMOS Serial EEPROM
(Tape and Reel)
512K Bit 2.5V I2C CMOS Serial EEPROM
512K Bit 2.5V I2C CMOS Serial EEPROM
(Tape and Reel)
Temperature Range:
I
=
-40°C to+85°C
Package:
P
SM
=
=
Plastic DIP (300 mil Body), 8-lead
Plastic SOIJ (5.28 mm Body), 8-lead
© 2008 Microchip Technology Inc.
c)
d)
24AA515T-I/SM: Tape and Reel, Industrial
Temperature, SOIJ package.
24LC515-I/P: Industrial Temperature, PDIP
package.
24LC515-I/SM: Industrial Temperature,
SOIJ package.
24LC515T-I/SM: Tape and Reel, Industrial
Temperature, SOIJ package.
DS21673G-page 21
24AA515/24LC515/24FC515
NOTES:
DS21673G-page 22
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, rfPIC and SmartShunt are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS21673G-page 23
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS21673G-page 24
© 2008 Microchip Technology Inc.