PDF Data Sheet Rev. A

12-Bit, 80 MSPS/105 MSPS/125 MSPS,
1.8 V Analog-to-Digital Converter
AD9233
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AVDD
AD9233
VIN+
VIN–
GENERAL DESCRIPTION
8-STAGE
1 1/2-BIT PIPELINE
MDAC1
SHA
8
4
3
REFB
CORRECTION LOGIC
OR
13
OUTPUT BUFFERS
DCO
D11 (MSB)
VREF
D0 (LSB)
SENSE
0.5V
REF
SELECT
AGND
CLOCK
DUTY CYCLE
STABILIZER
CLK+
CLK–
SCLK/DFS
MODE
SELECT
PDWN
SDIO/DCS
CSB
DRGND
Figure 1.
The digital output data is presented in offset binary, Gray code, or
twos complement formats. A data output clock (DCO) is provided
to ensure proper latch timing with receiving logic.
The AD9233 is available in a 48-lead LFCSP and is specified
over the industrial temperature range (−40°C to +85°C).
The AD9233 is a monolithic, single 1.8 V supply, 12-bit, 80 MSPS/
105 MSPS/125 MSPS analog-to-digital converter (ADC), featuring
a high performance sample-and-hold amplifier (SHA) and onchip voltage reference. The product uses a multistage differential
pipeline architecture with output error correction logic to
provide 12-bit accuracy at 125 MSPS data rates and guarantees
no missing codes over the full operating temperature range.
PRODUCT HIGHLIGHTS
The wide bandwidth, truly differential SHA allows a variety of
user-selectable input ranges and offsets, including single-ended
applications. It is suitable for multiplexed systems that switch
full-scale voltage levels in successive channels and for sampling
single-channel inputs at frequencies well beyond the Nyquist rate.
Combined with power and cost savings over previously available
ADCs, the AD9233 is suitable for applications in communications,
imaging, and medical ultrasound.
A differential clock input controls all internal conversion cycles. A
duty cycle stabilizer (DCS) compensates for wide variations in the
clock duty cycle while maintaining excellent overall ADC
performance.
A/D
A/D
REFT
APPLICATIONS
Ultrasound equipment
IF sampling in communications receivers
IS-95, CDMA-One, IMT-2000
Battery-powered instruments
Hand-held scopemeters
Low cost digital oscilloscopes
DRVDD
05492-001
1.8 V analog supply operation
1.8 V to 3.3 V output supply
SNR = 69.5 dBc (70.5 dBFS) to 70 MHz input
SFDR = 85 dBc to 70 MHz input
Low power: 395 mW @ 125 MSPS
Differential input with 650 MHz bandwidth
On-chip voltage reference and sample-and-hold amplifier
DNL = ±0.15 LSB
Flexible analog input: 1 V p-p to 2 V p-p range
Offset binary, Gray code, or twos complement data format
Clock duty cycle stabilizer
Data output clock
Serial port control
Built-in selectable digital test pattern generation
Programmable clock and data alignment
1.
The AD9233 operates from a single 1.8 V power supply
and features a separate digital output driver supply to
accommodate 1.8 V to 3.3 V logic families.
2.
The patented SHA input maintains excellent performance
for input frequencies up to 225 MHz.
3.
The clock DCS maintains overall ADC performance over a
wide range of clock pulse widths.
4.
A standard serial port interface supports various product
features and functions, such as data formatting (offset
binary, twos complement, or Gray coding), enabling the
clock DCS, power-down, and voltage reference mode.
5.
The AD9233 is pin compatible with the AD9246, allowing
a simple migration from 12 bits to 14 bits.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD9233
TABLE OF CONTENTS
Features .............................................................................................. 1
Timing ......................................................................................... 22
Applications....................................................................................... 1
Serial Port Interface (SPI).............................................................. 23
General Description ......................................................................... 1
Configuration Using the SPI..................................................... 23
Functional Block Diagram .............................................................. 1
Hardware Interface..................................................................... 23
Product Highlights ........................................................................... 1
Configuration Without the SPI ................................................ 23
Revision History ............................................................................... 3
Memory Map .................................................................................. 24
Specifications..................................................................................... 4
Reading the Memory Map Table.............................................. 24
DC Specifications ......................................................................... 4
Layout Considerations................................................................... 27
AC Specifications.......................................................................... 5
Power and Ground Recommendations ................................... 27
Digital Specifications ................................................................... 6
CML ............................................................................................. 27
Switching Specifications .............................................................. 7
RBIAS........................................................................................... 27
Timing Diagram ........................................................................... 7
Reference Decoupling................................................................ 27
Absolute Maximum Ratings............................................................ 8
Evaluation Board ............................................................................ 28
Thermal Resistance ...................................................................... 8
Power Supplies............................................................................ 28
ESD Caution.................................................................................. 8
Input Signals................................................................................ 28
Pin Configuration and Function Descriptions............................. 9
Output Signals ............................................................................ 28
Equivalent Circuits ......................................................................... 10
Default Operation and Jumper Selection Settings................. 29
Typical Performance Characteristics ........................................... 11
Alternative Clock Configurations............................................ 29
Theory of Operation ...................................................................... 15
Alternative Analog Input Drive Configuration...................... 30
Analog Input Considerations.................................................... 15
Schematics ....................................................................................... 31
Voltage Reference ....................................................................... 17
Evaluation Board Layouts ......................................................... 36
Clock Input Considerations ...................................................... 18
Bill of Materials (BOM)............................................................. 39
Jitter Considerations .................................................................. 19
Outline Dimensions ....................................................................... 42
Power Dissipation and Standby Mode..................................... 20
Ordering Guide .......................................................................... 42
Digital Outputs ........................................................................... 21
Rev. A | Page 2 of 44
AD9233
REVISION HISTORY
8/06—Rev. 0 to Rev. A
Updated Format.................................................................. Universal
Added 80 MSPS .................................................................. Universal
Deleted Figure 19, Figure 20, Figure 22, and Figure 23;
Renumbered Sequentially ..............................................................11
Deleted Figure 24, Figure 25, and Figure 27 to Figure 29;
Renumbered Sequentially ..............................................................12
Deleted Figure 31 and Figure 34; Renumbered Sequentially ....13
Deleted Figure 37, Figure 38, Figure 40, and Figure 41;
Renumbered Sequentially ..............................................................14
Deleted Figure 46; Renumbered Sequentially .............................15
Deleted Figure 52; Renumbered Sequentially .............................16
Changes to Figure 40 ......................................................................16
Changes to Figure 46 ......................................................................18
Inserted Figure 54; Renumbered Sequentially ............................20
Changes to Digital Outputs Section .............................................21
Changes to Timing Section............................................................22
Added Data Clock Output (DCO) Section..................................22
Changes to Configuration Using the SPI Section and
Configuration Without the SPI Section .......................................23
Changes to Table 15 ........................................................................25
Changes to Table 16 ........................................................................39
Changes to Ordering Guide...........................................................42
4/06—Revision 0: Initial Version
Rev. A | Page 3 of 44
AD9233
SPECIFICATIONS
DC SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS,
DCS enabled, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error
Differential Nonlinearity (DNL) 1
Integral Nonlinearity (INL)1
TEMPERATURE DRIFT
Offset Error
Gain Error
INTERNAL VOLTAGE REFERENCE
Output Voltage Error (1 V Mode)
Load Regulation @ 1.0 mA
INPUT REFERRED NOISE
VREF = 1.0 V
ANALOG INPUT
Input Span, VREF = 1.0 V
Input Capacitance 2
REFERENCE INPUT RESISTANCE
POWER SUPPLIES
Supply Voltage
AVDD
DRVDD
Supply Current
IAVDD1
IDRVDD1 (DRVDD = 1.8 V)
IDRVDD1 (DRVDD = 3.3 V)
POWER CONSUMPTION
DC Input
Sine Wave Input1 (DRVDD = 1.8 V)
Sine Wave Input1 (DRVDD = 3.3 V)
Standby 3
Power-Down
Temp
Full
AD9233BCPZ-80
Min
Typ
Max
12
AD9233BCPZ-105
Min
Typ
Max
12
AD9233BCPZ-125
Min
Typ
Max
12
Guaranteed
±0.3
±0.5
±0.2
±4.7
±0.3
±0.2
±1.2
±0.5
Guaranteed
±0.3
±0.8
±0.2
±4.9
±0.5
±0.2
±1.2
±0.5
Guaranteed
±0.3
±0.8
±0.2
±3.9
±0.5
±0.2
±1.2
±0.5
Full
Full
Full
Full
25°C
Full
25°C
±15
±95
Full
Full
±5
7
25°C
0.34
0.34
0.34
LSB rms
Full
Full
Full
2
8
6
2
8
6
2
8
6
V p-p
pF
kΩ
1.7
1.7
±20
1.8
3.3
1.9
3.6
Full
Full
Full
138
7
12
Full
Full
Full
Full
Full
248
261
288
40
1.8
±5
7
±35
1.8
3.3
1.9
3.6
155
178
8
14
279
320
335
365
40
1.8
1
1.7
1.7
±15
±95
% FSR
% FSR
LSB
LSB
LSB
LSB
Full
Full
Full
Full
±15
±95
Unit
Bits
±5
7
1.7
1.7
ppm/°C
ppm/°C
±35
mV
mV
1.8
3.3
1.9
3.6
V
V
194
220
10
17
236
mA
mA
mA
350
395
415
452
40
1.8
425
mW
mW
mW
mW
mW
Measured with a low input frequency, full-scale sine wave, with approximately 5 pF loading on each output bit.
Input capacitance refers to the effective capacitance between one differential input pin and AGND. Refer to Figure 4 for the equivalent analog input structure.
3
Standby power is measured with a dc input, the CLK pin inactive (set to AVDD or AGND).
2
Rev. A | Page 4 of 44
AD9233
AC SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS,
DCS enabled, unless otherwise noted.
Table 2.
Parameter 1
SIGNAL-TO-NOISE-RATIO (SNR)
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
SIGNAL-TO-NOISE AND DISTORTION (SINAD)
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
WORST SECOND OR THIRD HARMONIC
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
WORST OTHER (HARMONIC OR SPUR)
fIN = 2.4 MHz
fIN = 70 MHz
fIN = 100 MHz
fIN = 170 MHz
TWO-TONE SFDR
fIN = 30 MHz (−7 dBFS), 31 MHz (−7 dBFS)
fIN = 170 MHz (−7 dBFS), 171 MHz (−7 dBFS)
ANALOG INPUT BANDWIDTH
1
Temp
25°C
25°C
Full
25°C
25°C
25°C
25°C
Full
25°C
25°C
AD9233BCPZ-80
Min Typ
Max
AD9233BCPZ-105
Min Typ
Max
69.5
69.5
AD9233BCPZ-125
Min Typ
Max
69.5
69.5
68.9
69.5
69.5
68.3
dBc
dBc
dBc
dBc
dBc
68.3
69.4
68.9
69.4
68.9
69.4
68.9
69.2
69.2
69.2
69.2
69.2
69.2
Unit
69.1
68.6
69.1
68.6
69.1
68.6
dBc
dBc
dBc
dBc
dBc
25°C
25°C
25°C
25°C
11.4
11.4
11.4
11.3
11.4
11.4
11.4
11.3
11.4
11.4
11.4
11.3
Bits
Bits
Bits
Bits
25°C
25°C
Full
25°C
25°C
−90.0
−85.0
−90.0
−85.0
−90.0
−85.0
−85.0
−83.5
−85.0
−83.5
−85.0
−83.5
dBc
dBc
dBc
dBc
dBc
25°C
25°C
Full
25°C
25°C
90.0
85.0
90.0
85.0
90.0
85.0
68.5
67.3
67.3
−76.0
76.0
−73.0
73.0
−73.0
dBc
dBc
dBc
dBc
dBc
73.0
85.0
83.5
85.0
83.5
85.0
83.5
25°C
25°C
Full
25°C
25°C
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
−90.0
dBc
dBc
dBc
dBc
dBc
25°C
25°C
25°C
87
83
650
87
83
650
85
84
650
dBFS
dBFS
MHz
−85.0
See AN-835, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
Rev. A | Page 5 of 44
−81.0
−81.0
AD9233
DIGITAL SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS,
DCS enabled, unless otherwise noted.
Table 3.
Parameter
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Internal Common-Mode Bias
Differential Input Voltage
Input Voltage Range
Input Common-Mode Range
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Input Resistance
Input Capacitance
LOGIC INPUTS (SCLK/DFS, OE, PWDN)
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Input Resistance
Input Capacitance
LOGIC INPUTS (CSB)
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Input Resistance
Input Capacitance
LOGIC INPUTS (SDIO/DCS)
High Level Input Voltage (VIH)
Low Level Input Voltage (VIL)
High Level Input Current (IIH)
Low Level Input Current (IIL)
Input Resistance
Input Capacitance
DIGITAL OUTPUTS
DRVDD = 3.3 V
High Level Output Voltage (VOH, IOH = 50 μA)
High Level Output Voltage (VOH, IOH = 0.5 mA)
Low Level Output Voltage (VOL, IOL = 1.6 mA)
Low Level Output Voltage (VOL, IOL = 50 μA)
DRVDD = 1.8 V
High Level Output Voltage (VOH, IOH = 50 μA)
High Level Output Voltage (VOH, IOH = 0.5 mA)
Low Level Output Voltage (VOL, IOL = 1.6 mA)
Low Level Output Voltage (VOL, IOL = 50 μA)
AD9233BCPZ-80/105/125
Typ
Max
Temp
Min
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
CMOS/LVDS/LVPECL
1.2
0.2
6
AVDD − 0.3
AVDD + 1.6
1.1
AVDD
1.2
3.6
0
0.8
−10
+10
−10
+10
8
10
12
4
Full
Full
Full
Full
Full
Full
1.2
0
−50
−10
Full
Full
Full
Full
Full
Full
1.2
0
−10
+40
Full
Full
Full
Full
Full
Full
1.2
0
−10
+40
Full
Full
Full
Full
3.29
3.25
Full
Full
Full
Full
1.79
1.75
Rev. A | Page 6 of 44
Unit
V
V p-p
V
V
V
V
μA
μA
kΩ
pF
3.6
0.8
−75
+10
V
V
μA
μA
kΩ
pF
3.6
0.8
+10
+135
V
V
μA
μA
kΩ
pF
DRVDD + 0.3
0.8
+10
+130
V
V
μA
μA
kΩ
pF
30
2
26
2
26
5
0.2
0.05
V
V
V
V
0.2
0.05
V
V
V
V
AD9233
SWITCHING SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 2.5 V, unless otherwise noted.
Table 4.
Parameter 1
CLOCK INPUT PARAMETERS
Conversion Rate, DCS Enabled
Conversion Rate, DCS Disabled
CLK Period
CLK Pulse Width High, DCS Enabled
CLK Pulse Width High, DCS Disabled
DATA OUTPUT PARAMETERS
Data Propagation Delay (tPD) 2
DCO Propagation Delay (tDCO)
Setup Time (tS)
Hold Time (tH)
Pipeline Delay (Latency)
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tJ)
Wake-Up Time 3
OUT-OF-RANGE RECOVERY TIME
SERIAL PORT INTERFACE 4
SCLK Period (tCLK)
SCLK Pulse Width High Time (tHI)
SCLK Pulse Width Low Time (tLO)
SDIO to SCLK Setup Time (tDS)
SDIO to SCLK Hold Time (tDH)
CSB to SCLK Setup Time (tS)
CSB to SCLK Hold Time (tH)
Temp
AD9233BCPZ-80
Min
Typ
Max
AD9233BCPZ-105
Min
Typ
Max
AD9233BCPZ-125
Min
Typ
Max
Unit
Full
Full
Full
Full
Full
20
10
12.5
3.75
5.63
MSPS
MSPS
ns
ns
ns
Full
Full
Full
Full
Full
Full
Full
Full
Full
3.1
80
80
4.9
5.9
Full
Full
Full
Full
Full
Full
Full
6.25
6.25
8.75
6.88
20
10
9.5
2.85
4.28
3.9
4.4
5.7
6.8
12
0.8
0.1
350
2
4.8
3.1
3.4
4.4
40
16
16
5
2
5
2
105
105
4.75
4.75
6.65
5.23
20
10
8
2.4
3.6
3.9
4.4
4.3
5.3
12
0.8
0.1
350
2
4.8
3.1
125
125
2.6
3.7
40
16
16
5
2
5
2
40
16
16
5
2
5
2
See AN-835, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
Output propagation delay is measured from CLK 50% transition to DATA 50% transition, with 5 pF load.
3
Wake-up time is dependant on the value of the decoupling capacitors, values shown with 0.1 μF capacitor across REFT and REFB.
4
See Figure 57 and the Serial Port Interface (SPI) section.
2
TIMING DIAGRAM
N+2
N+3
N
N+4
tA
N+8
N+5
N+6
N+7
N–7
N–6
tCLK
CLK+
CLK–
tPD
N – 13
tS
N – 12
N – 11
tH
N – 10
N–9
N–8
tDCO
DCO
Figure 2. Timing Diagram
Rev. A | Page 7 of 44
tCLK
N–5
N–4
05492-083
DATA
5.6
4.4
3.9
4.4
3.5
4.5
12
0.8
0.1
350
3
4.8
ns
ns
ns
ns
cycles
ns
ps rms
ms
cycles
ns
ns
ns
ns
ns
ns
ns
1
N+1
4
4
AD9233
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
ELECTRICAL
AVDD to AGND
DRVDD to DRGND
AGND to DRGND
AVDD to DRVDD
D0 through D11 to DRGND
DCO to DRGND
OR to DRGND
CLK+ to AGND
CLK− to AGND
VIN+ to AGND
VIN− to AGND
VREF to AGND
SENSE to AGND
REFT to AGND
REFB to AGND
SDIO/DCS to DRGND
PDWN to AGND
CSB to AGND
SCLK/DFS to AGND
OEB to AGND
ENVIRONMENTAL
Storage Temperature Range
Operating Temperature Range
Lead Temperature
(Soldering 10 Sec)
Junction Temperature
Rating
−0.3 V to +2.0 V
−0.3 V to +3.9 V
−0.3 V to +0.3 V
−3.9 V to +2.0 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to AVDD + 1.3 V
−0.3 V to AVDD + 1.3 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
−0.3 V to +3.9 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
The exposed paddle must be soldered to the ground plane for
the LFCSP package. Soldering the exposed paddle to the
customer board increases the reliability of the solder joints,
maximizing the thermal capability of the package.
Table 6.
Package Type
48-lead LFCSP (CP-48-3)
θJA
26.4
θJC
2.4
Unit
°C/W
Typical θJA and θJC are specified for a 4-layer board in still air.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, metal in direct contact with the package leads from
metal traces, and through holes, ground, and power planes,
reduces the θJA.
–65°C to +125°C
–40°C to +85°C
300°C
150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 8 of 44
AD9233
48
47
46
45
44
43
42
41
40
39
38
37
DRVDD
DRGND
NC
NC
DCO
OEB
AVDD
AGND
AVDD
CLK–
CLK+
AGND
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
(LSB) D0
D1
1
2
AD9233
TOP VIEW
(Not to Scale)
PIN 0 (EXPOSED PADDLE): AGND
36
35
34
33
32
31
30
29
28
27
26
25
PDWN
RBIAS
CML
AVDD
AGND
VIN–
VIN+
AGND
REFT
REFB
VREF
SENSE
05492-003
D10
(MSB) D11
OR
DRGND
DRVDD
SDIO/DCS
SCLK/DFS
CSB
AGND
AVDD
AGND
AVDD
13
14
15
16
17
18
19
20
21
22
23
24
D2 3
D3 4
D4 5
D5 6
DRGND 7
DRVDD 8
D6 9
D7 10
D8 11
D9 12
PIN 1
INDICATOR
NC = NO CONNECT
Figure 3. Pin Configuration
Table 7. Pin Function Description
Pin No.
0, 21, 23, 29,
32, 37, 41
1 to 6, 9 to 14
7, 16, 47
8, 17, 48
15
18
Mnemonic
AGND
Description
Analog Ground. (Pin 0 is the exposed thermal pad on the bottom of the package.)
D0 (LSB) to D11 (MSB)
DRGND
DRVDD
OR
SDIO/DCS
19
20
22, 24, 33, 40, 42
25
26
27
28
30
31
34
35
SCLK/DFS
CSB
AVDD
SENSE
VREF
REFB
REFT
VIN+
VIN–
CML
RBIAS
36
38
39
43
44
45, 46
PDWN
CLK+
CLK–
OEB
DCO
NC
Data Output Bits.
Digital Output Ground.
Digital Output Driver Supply (1.8 V to 3.3 V).
Out-of-Range Indicator.
Serial Port Interface (SPI)® Data Input/Output (Serial Port Mode); Duty Cycle Stabilizer Select
(External Pin Mode). See Table 10.
SPI Clock (Serial Port Mode); Data Format Select Pin (External Pin Mode). See Table 10.
SPI Chip Select (Active Low).
Analog Power Supply.
Reference Mode Selection. See Table 9.
Voltage Reference Input/Output.
Differential Reference (−).
Differential Reference (+).
Analog Input Pin (+).
Analog Input Pin (−).
Common-Mode Level Bias Output.
External Bias Resister Connection. A 10 kΩ resister must be connected between this pin and
analog ground (AGND).
Power-Down Function Select.
Clock Input (+).
Clock Input (−).
Output Enable (Active Low).
Data Clock Output.
No Connection.
Rev. A | Page 9 of 44
AD9233
EQUIVALENT CIRCUITS
1kΩ
SCLK/DFS
OEB
PDWN
30kΩ
05492-004
05492-008
VIN
Figure 4. Equivalent Analog Input Circuit
Figure 8. Equivalent SCLK/DFS, OEB, PDWN Input Circuit
AVDD
AVDD
26kΩ
1.2V
1kΩ
CLK–
05492-005
CLK+
CSB
10kΩ
05492-010
10kΩ
Figure 9. Equivalent CSB Input Circuit
Figure 5. Equivalent Clock Input Circuit
DRVDD
SENSE
1kΩ
1kΩ
05492-006
05492-011
SDIO/DCS
Figure 10. Equivalent SENSE Circuit
Figure 6. Equivalent SDIO/DCS Input Circuit
DRVDD
AVDD
05492-007
DRGND
6kΩ
05492-012
VREF
Figure 11. Equivalent VREF Circuit
Figure 7. Equivalent Digital Output Circuit
Rev. A | Page 10 of 44
AD9233
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 1.8 V; DRVDD = 2.5 V; maximum sample rate, DCS enabled, 1 V internal reference; 2 V p-p differential input; AIN =
−1.0 dBFS; 64k sample; TA = 25°C, unless otherwise noted. All figures show typical performance for all speed grades.
0
0
125MSPS
2.3MHz @ –1dBFS
SNR = 69.5dBc (70.5dBFS)
ENOB = 11.2 BITS
SFDR = 90.0dBc
–60
–80
–80
–100
–120
–120
0
15.625
31.250
FREQUENCY (MHz)
46.875
–140
62.500
15.625
31.250
FREQUENCY (MHz)
0
125MSPS
30.3MHz @ –1dBFS
SNR = 69.5dBc (70.5dBFS)
ENOB = 11.2 BITS
SFDR = 88.8dBc
–80
–40
–60
–80
–100
–120
–120
05492-014
–100
31.250
FREQUENCY (MHz)
46.875
–140
62.500
0
125MSPS
70.3MHz @ –1dBFS
SNR = 69.5dBc (70.5dBFS)
ENOB = 11.2 BITS
SFDR = 85.0dBc
–20
AMPLITUDE (dBFS)
–60
–80
05492-015
–120
46.875
62.500
–80
–120
31.250
FREQUENCY (MHz)
46.875
–60
–100
15.625
31.250
FREQUENCY (MHz)
–40
–100
–140
15.625
125MSPS
170.3MHz @ –1dBFS
SNR = 68.9dBc (69.9dBFS)
ENOB = 11.1 BITS
SFDR = 83.5dBc
–20
–40
0
0
Figure 16. AD9233-125 Single-Tone FFT with FIN = 140.3 MHz
Figure 13. AD9233-125 Single-Tone FFT with FIN = 30.3 MHz
0
05492-017
AMPLITUDE (dBFS)
–60
15.625
62.500
125MSPS
140.3MHz @ –1dBFS
SNR = 69.0dBc (70.0dBFS)
ENOB = 11.1 BITS
SFDR = 85.0dBc
–20
–40
0
46.875
62.500
Figure 14. AD9233-125 Single-Tone FFT with FIN = 70.3 MHz
–140
05492-018
–20
–140
0
Figure 15. AD9233-125 Single-Tone FFT with FIN = 100.3 MHz
0
AMPLITUDE (dBFS)
–60
–100
Figure 12. AD9233-125 Single-Tone FFT with FIN = 2.3 MHz
AMPLITUDE (dBFS)
–40
05492-016
AMPLITUDE (dBFS)
–40
–140
125MSPS
100.3MHz @ –1dBFS
SNR = 69.4dBc (70.4dBFS)
ENOB = 11.2 BITS
SFDR = 85.0dBc
–20
05492-013
AMPLITUDE (dBFS)
–20
0
15.625
31.250
FREQUENCY (MHz)
46.875
62.500
Figure 17. AD9233-125 Single-Tone FFT with FIN = 170.3 MHz
Rev. A | Page 11 of 44
AD9233
0
–20
95
SFDR = –40°C
90
–40
SNR/SFDR (dBc)
–60
–80
–100
75
SNR = +25°C
SNR = –40°C
15.625
31.250
FREQUENCY (MHz)
46.875
SNR = +85°C
60
62.500
0
05492-021
05492-019
0
50
100
200
250
Figure 21. AD9233 Single-Tone SNR/SFDR vs.
Input Frequency (FIN) and Temperature with 2 V p-p Full Scale
100
125MSPS
300.3MHz @ –1dBFS
SNR = 67.8dBc (68.8dBFS)
ENOB = 10.8 BITS
SFDR = 77.4dBc
–20
95
SNR/SFDR (dBc)
–60
–80
75
65
05492-029
–120
31.250
46.875
SFDR = –40°C
80
70
15.625
SFDR = +25°C
85
–100
0
SFDR = +85°C
90
–40
SNR = +25°C
SNR = –40°C
SNR = +85°C
60
62.500
0
50
100
150
200
250
INPUT FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 22. AD9233 Single-Tone SNR/SFDR vs.
Input Frequency (FIN) and Temperature with 1 V p-p Full Scale
Figure 19. AD9233-125 Single-Tone FFT with FIN = 300.3 MHz
1.0
120
SFDR (dBFS)
0.8
80
GAIN/OFFSET ERROR (%FSR)
100
SNR (dBFS)
60
40
SFDR (dBc)
85dB REFERENCE LINE
20
OFFSET ERROR
0.5
0.3
0
GAIN ERROR
–0.3
–0.5
05492-031
–0.8
SNR (dBc)
0
–90
–80
–70
–60
–50
–40
–30
–20
INPUT AMPLITUDE (dBFS)
–10
0
05492-091
SNR/SFDR (dBc and dBFS)
150
INPUT FREQUENCY (MHz)
0
–140
SFDR = +85°C
65
Figure 18. AD9233-125 Single-Tone FFT with FIN = 225.3 MHz
AMPLITUDE (dBFS)
80
70
–120
–140
SFDR = +25°C
85
05492-022
AMPLITUDE (dBFS)
100
125MSPS
225.3MHz @ –1dBFS
SNR = 68.5dBc (69.5dBFS)
ENOB = 11.0 BITS
SFDR = 80.4dBc
–1.0
–40
–20
0
20
40
60
TEMPERATURE (°C)
Figure 23. AD9233 Gain and Offset vs. Temperature
Figure 20. AD9233 Single-Tone SNR/SFDR vs.
Input Amplitude (AIN) with FIN = 2.4 MHz
Rev. A | Page 12 of 44
80
AD9233
0
0
125MSPS
29.1MHz @ –7dBFS
32.1MHz @ –7dBFS
SFDR = 85dBc (92dBFS)
–20
SFDR/IMD3 (dBc and dBFS)
–40
–60
–80
–100
SFDR (dBc)
–40
IMD3 (dBc)
–60
–80
SFDR (dBFS)
05492-024
–140
0
15.625
31.250
46.875
IMD3 (dBFS)
–120
–90
62.500
–78
–66
FREQUENCY (MHz)
–30
–18
–6
0
125MSPS
169.1MHz @ –7dBFS
172.1MHz @ –7dBFS
SFDR = 84dBc (91dBFS)
–20
SFDR/IMD3 (dBc and dBFS)
–20
AMPLITUDE (dBFS)
–42
Figure 27. AD9233 Two-Tone SFDR/IMD vs.
Input Amplitude (AIN) with FIN1 = 29.1 MHz, FIN2 = 32.1 MHz
0
–40
–60
–80
–100
SFDR (dBc)
–40
IMD3 (dBFS)
–60
–80
SFDR (dBFS)
–100
05492-025
–120
0
15.625
31.250
46.875
–120
–90
62.500
FREQUENCY (MHz)
–66
–54
–42
–30
–18
–6
Figure 28. AD9233 Two-Tone SFDR/IMD vs.
Input Amplitude (AIN) with FIN1 = 169.1 MHz, FIN2 = 172.1 MHz
0
–20
–20
AMPLITUDE (dBFS)
0
–40
–60
–80
NPR = 61.9dBc
NOTCH @ 18.5MHz
NOTCH WIDTH = 3MHz
–40
–60
–80
05492-086
0
15.36
30.72
46.08
61.44
–120
05492-090
–100
–100
–120
IMD3 (dBFS)
–78
INPUT AMPLITUDE (dBFS)
Figure 25. AD9233-125 Two-Tone FFT with FIN1 = 169.1 MHz, FIN2 = 172.1 MHz
AMPLITUDE (dBFS)
–54
ANALOG INPUT LEVEL (dBFS)
Figure 24. AD9233-125 Two-Tone FFT with FIN1 = 29.1 MHz, FIN2 = 32.1 MHz
–140
05492-035
–100
–120
05492-080
AMPLITUDE (dBFS)
–20
0
15.625
31.250
46.875
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 29. AD9233-125 Noise Power Ratio
Figure 26. AD9233-125 Two 64k WCDMA Carriers
with FIN = 215.04 MHz, FS = 122.88 MSPS
Rev. A | Page 13 of 44
62.500
AD9233
10
100
0.34 LSB rms
SFDR
8
NUMBER OF HITS (1M)
SNR/SFDR (dBc)
90
85
80
75
SNR
05492-027
5
4
2
70
65
6
25
45
65
85
105
05492-085
95
0
125
N–1
N
Figure 33. AD9233 Grounded Input Histogram
Figure 30. AD9233 Single-Tone SNR/SFDR vs.
Clock Frequency (FS) with FIN = 2.4 MHz
0.35
100
SFDR DCS = ON
0.25
90
INL ERROR (LSB)
SNR DCS = ON
70
60
0.05
–0.05
–0.15
50
05492-026
–0.25
SNR DCS = OFF
20
40
60
–0.35
80
05492-023
SNR/SFDR (dBc)
0.15
SFDR DCS = OFF
80
40
0
1024
DUTY CYCLE (%)
Figure 31. AD9233 SNR/SFDR vs. Duty Cycle with FIN = 10.3 MHz
2048
OUTPUT CODE
3072
4096
Figure 34. AD9233 INL with FIN = 10.3 MHz
90
0.15
SFDR
0.10
DNL ERROR (LSB)
85
80
75
0.05
0
–0.05
70
65
0.5
0.7
0.9
1.1
1.3
INPUT COMMON-MODE VOLTAGE (V)
Figure 32. AD9233 SNR/SFDR vs.
Input Common Mode (VCM) with FIN = 30 MHz
–0.10
–0.15
05492-020
SNR
05492-028
SNR/SFDR (dBc)
N+1
OUTPUT CODE
CLOCK FREQUENCY (MSPS)
0
1024
2048
OUTPUT CODE
3072
Figure 35. AD9233 DNL with FIN = 10.3 MHz
Rev. A | Page 14 of 44
4096
AD9233
THEORY OF OPERATION
S
The AD9233 architecture consists of a front-end SHA followed
by a pipelined switched capacitor ADC. The quantized outputs
from each stage are combined into a final 12-bit result in the
digital correction logic. The pipelined architecture permits the
first stage to operate on a new input sample, while the
remaining stages operate on preceding samples. Sampling
occurs on the rising edge of the clock.
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended modes. The outputstaging block aligns the data, carries out the error correction,
and passes the data to the output buffers. The output buffers are
powered from a separate supply, allowing adjustment of the
output voltage swing. During power-down, the output buffers
proceed into a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9233 is a differential switched
capacitor SHA that has been designed for optimum
performance while processing a differential input signal.
CS
VIN+
CPIN, PAR
S
H
CS
VIN–
CPIN, PAR
CH
S
05492-037
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
CH
S
Figure 36. Switched-Capacitor SHA Input
For best dynamic performance, the source impedances driving
VIN+ and VIN− should match such that common-mode
settling errors are symmetrical. These errors are reduced by the
common-mode rejection of the ADC.
An internal differential reference buffer creates two reference
voltages used to define the input span of the ADC core. The
span of the ADC core is set by the buffer to be 2 × VREF. The
reference voltages are not available to the user. Two bypass
points, REFT and REFB, are brought out for decoupling to
reduce the noise contributed by the internal reference buffer. It
is recommended that REFT be decoupled to REFB by a 0.1 μF
capacitor, as described in the Layout Considerations section.
Input Common Mode
The clock signal alternately switches the SHA between sample
mode and hold mode (see Figure 36). When the SHA is
switched into sample mode, the signal source must be capable
of charging the sample capacitors and settling within one-half
of a clock cycle. A small resistor in series with each input can
help reduce the peak transient current required from the output
stage of the driving source.
A shunt capacitor can be placed across the inputs to provide
dynamic charging currents. This passive network creates a lowpass filter at the ADC input; therefore, the precise values are
dependant upon the application.
In IF undersampling applications, any shunt capacitors should
be reduced. In combination with the driving source impedance,
these capacitors limit the input bandwidth. See Application
Notes AN-742, Frequency Domain Response of SwitchedCapacitor ADCs, and AN-827, A Resonant Approach To
Interfacing Amplifiers to Switched-Capacitor ADCs, and the
Analog Dialogue article, “Transformer-Coupled Front-End for
Wideband A/D Converters”, for more information.
The analog inputs of the AD9233 are not internally dc-biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device such that VCM = 0.55 × AVDD is
recommended for optimum performance; however, the device
functions over a wider range with reasonable performance (see
Figure 32). An on-board common-mode voltage reference is
included in the design and is available from the CML pin.
Optimum performance is achieved when the common-mode
voltage of the analog input is set by the CML pin voltage
(typically 0.55 × AVDD). The CML pin must be decoupled to
ground by a 0.1 μF capacitor, as described in the Layout
Considerations section.
Differential Input Configurations
Optimum performance is achieved by driving the AD9233 in a
differential input configuration. For baseband applications, the
AD8138 differential driver provides excellent performance and
a flexible interface to the ADC. The output common-mode
voltage of the AD8138 is easily set with the CML pin of the
AD9233 (see Figure 37), and the driver can be configured
in a Sallen-Key filter topology to provide band limiting of the
input signal.
Rev. A | Page 15 of 44
AD9233
49.9Ω
R
VIN+
AVDD
499Ω
AD9233
C
523Ω
R
CML
VIN–
05492-038
AD8138
0.1µF
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9233. For applications
where SNR is a key parameter, transformer coupling is the
recommended input. For applications where SFDR is a key
parameter, differential double balun coupling is the recommended input configuration. An example is shown in Figure 39.
499Ω
499Ω
Figure 37. Differential Input Configuration Using the AD8138
As an alternative to using a transformer-coupled input at
frequencies in the second Nyquist zone, the AD8352 differential
driver can be used. An example is shown in Figure 40.
For baseband applications where SNR is a key parameter,
differential transformer coupling is the recommended input
configuration. An example is shown in Figure 38. The CML
voltage can be connected to the center tap of the secondary
winding of the transformer to bias the analog input.
In any configuration, the value of the shunt capacitor, C, is
dependent on the input frequency and source impedance
and may need to be reduced or removed. Table 8 displays
recommended values to set the RC network. However, these
values are dependant on the input signal and should only be
used as a starting guide.
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies
below a few MHz, and excessive signal power can cause core
saturation, which leads to distortion.
R
49.9Ω
Frequency Range (MHz)
0 to 70
70 to 200
200 to 300
>300
VIN+
AD9233
C
R
CML
VIN–
R Series (Ω)
33
33
15
15
05492-039
0.1µF
Figure 38. Differential Transformer-Coupled Configuration
0.1µF
0.1µF
R
VIN+
2V p-p
25Ω
PA
S
P
S
25Ω
0.1µF
AD9233
C
0.1µF
R
VIN–
CML
05492-089
2V p-p
Table 8. RC Network Recommended Values
Figure 39. Differential Double Balun Input Configuration
VCC
0.1µF
0.1µF
0Ω
ANALOG INPUT
16
1
8, 13
11
0.1µF
R
2
VIN+
200Ω
RD
CD
AD8352
RG
3
10
0.1µF
200Ω
C
R
4
5
ANALOG INPUT
0.1µF
0Ω
AD9233
VIN–
CML
14
0.1µF
0.1µF
Figure 40. Differential Input Configuration Using the AD8352
Rev. A | Page 16 of 44
05492-088
1V p-p
C Differential (pF)
15
5
5
Open
AD9233
Single-Ended Input Configuration
Although not recommended, it is possible to operate the
AD9233 in a single-ended input configuration, as long as the
input voltage swing is within the AVDD supply. Single-ended
operation can provide adequate performance in cost-sensitive
applications. In this configuration, SFDR and distortion
performance degrade due to the large input common-mode
swing. If the source impedances on each input are matched,
there should be little effect on SNR performance. Figure 41
details a typical single-ended input configuration.
AVDD
10µF
This puts the reference amplifier in a noninverting mode with
the VREF output defined as
R2 ⎞
VREF = 0.5 × ⎛⎜1 +
⎟
⎝ R1 ⎠
If the SENSE pin is connected to the AVDD pin, the reference
amplifier is disabled, and an external reference voltage can be
applied to the VREF pin (see the External Reference Operation
section).
The input range of the ADC always equals twice the voltage at
the reference pin for either an internal or an external reference.
AVDD
1kΩ
10µF
0.1µF
C
R
ADC
AD9233
VIN–
1kΩ
ADC
CORE
VIN–
–
1kΩ
REFT
0.1µF
REFB
VREF
Figure 41. Single-Ended Input Configuration
0.1µF
0.1µF
VOLTAGE REFERENCE
SELECT
LOGIC
SENSE
A stable and accurate voltage reference is built into the AD9233.
The input range is adjustable by varying the reference voltage
applied to the AD9233, using either the internal reference or an
externally applied reference voltage. The input span of the ADC
tracks reference voltage changes linearly. The various reference
modes are summarized in the following sections. The Reference
Decoupling section describes the best practices and requirements
for PCB layout of the reference.
05492-043
0.5V
AD9233
VIN–
ADC
CORE
–
VIN+
–
Figure 42. Internal Reference Configuration
REFT
Internal Reference Connection
A comparator within the AD9233 detects the potential at the
SENSE pin and configures the reference into four possible
states, which are summarized in Table 9. If SENSE is grounded,
the reference amplifier switch is connected to the internal
resistor divider (see Figure 42), setting VREF to 1 V.
0.1µF
REFB
VREF
0.1µF
0.1µF
R2
SENSE
Connecting the SENSE pin to VREF switches the reference
amplifier output to the SENSE pin, completing the loop and
providing a 0.5 V reference output. If a resistor divider is
connected external to the chip, as shown in Figure 43, the
switch again sets to the SENSE pin.
R1
SELECT
LOGIC
0.5V
AD9233
05492-044
1V p-p
49.9Ω
VIN+
VIN+
05492-042
R
0.1µF
–
1kΩ
Figure 43. Programmable Reference Configuration
If the internal reference of the AD9233 is used to drive multiple
converters to improve gain matching, the loading of the
reference by the other converters must be considered. Figure 44
depicts how the internal reference voltage is affected by loading.
Rev. A | Page 17 of 44
AD9233
Table 9. Reference Configuration Summary
Selected Mode
External Reference
Internal Fixed Reference
Programmable Reference
Internal Fixed Reference
SENSE Voltage
AVDD
VREF
0.2 V to VREF
AGND to 0.2 V
Resulting VREF (V)
N/A
0.5
0.5 × (1 + R2/R1) (See Figure 43)
1.0
0
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9233 sample clock inputs
(CLK+ and CLK−) should be clocked with a differential signal.
The signal is typically ac-coupled into the CLK+ pin and the
CLK− pin via a transformer or capacitors. These pins are biased
internally (see Figure 5) and require no external bias.
–0.25
VREF = 1V
–0.50
Clock Input Options
–0.75
–1.00
05492-032
REFERENCE VOLTAGE ERROR (%)
VREF = 0.5V
–1.25
Resulting Differential Span (V p-p)
2 × External Reference
1.0
2 × VREF
2.0
0
0.5
1.0
2.0
1.5
The AD9233 has a very flexible clock input structure. The clock
input can be a CMOS, LVDS, LVPECL, or sine wave signal.
Regardless of the type of signal used, the jitter of the clock
source is of the most concern, as described in the Jitter
Considerations section.
LOAD CURRENT (mA)
Figure 44. VREF Accuracy vs. Load
External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift
characteristics. Figure 45 shows the typical drift characteristics
of the internal reference in both 1 V and 0.5 V modes.
VREF = 0.5V
8
MIN-CIRCUITS
ADT1–1WT, 1:1Z
0.1µF
XFMR
0.1µF
VREF = 1V
6
CLOCK
INPUT
50Ω
ADC
AD9233
0.1µF
CLK–
2
SCHOTTKY
DIODES:
HSMS2812
05492-048
0.1µF
Figure 46. Transformer Coupled Differential Clock
–20
0
20
40
TEMPERATURE (°C)
60
80
Figure 45. Typical VREF Drift
When the SENSE pin is tied to the AVDD pin, the internal
reference is disabled, allowing the use of an external reference.
An internal resistor divider loads the external reference with an
equivalent 6 kΩ load (see Figure 11). In addition, an internal
buffer generates the positive and negative full-scale references
for the ADC core. Therefore, the external reference must be
limited to a maximum of 1 V.
If a low jitter clock source is not available, another option is to
ac-couple a differential PECL signal to the sample clock input
pins, as shown in Figure 47. The AD9510/AD9511/AD9512/
AD9513/AD9514/AD9515 family of clock drivers offers
excellent jitter performance.
0.1µF
CLOCK
INPUT
CLOCK
INPUT
0.1µF
CLK+
CLK
0.1µF
AD951x
PECL DRIVER
100Ω
0.1µF
CLK
50Ω*
50Ω*
240Ω
240Ω
*50Ω RESISTORS ARE OPTIONAL
Figure 47. Differential PECL Sample Clock
Rev. A | Page 18 of 44
ADC
AD9233
CLK–
05492-049
0
–40
CLK+
100Ω
4
05492-033
REFERENCE VOLTAGE ERROR (mV)
10
Figure 46 shows one preferred method for clocking the
AD9233. A low jitter clock source is converted from singleended to a differential signal using an RF transformer. The
back-to-back Schottky diodes across the transformer secondary
limit clock excursions into the AD9233 to approximately
0.8 V p-p differential. This helps prevent the large voltage
swings of the clock from feeding through to other portions of
the AD9233 while preserving the fast rise and fall times of the
signal, which are critical to a low jitter performance.
AD9233
A third option is to ac-couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 48. The AD9510/
AD9511/AD9512/AD9513/AD9514/AD9515 family of clock
drivers offers excellent jitter performance.
0.1µF
CLOCK
INPUT
CLK+
AD951x
LVDS DRIVER
100Ω
0.1µF
CLK
50Ω*
ADC
AD9233
CLK–
05492-050
CLOCK
INPUT
0.1µF
CLK
0.1µF
and distortion performance are nearly flat for a wide range of
duty cycles when the DCS is on, as shown in Figure 31.
50Ω*
*50Ω RESISTORS ARE OPTIONAL
Figure 48. Differential LVDS Sample Clock
In some applications, it is acceptable to drive the sample clock
inputs with a single-ended CMOS signal. In such applications,
directly drive CLK+ from a CMOS gate, while bypassing the
CLK− pin to ground with a 0.1 μF capacitor. Although the
CLK+ input circuit supply is AVDD (1.8 V), this input is
designed to withstand input voltages up to 3.6 V, making the
selection of the drive logic voltage very flexible. When driving
CLK+ with a 1.8 V CMOS signal, it is required to bias the
CLK− pin with a 0.1 μF capacitor in parallel with a 39 kΩ
resistor (see Figure 49). The 39 kΩ resistor is not required when
driving CLK+ with a 3.3 V CMOS signal (see Figure 50).
VCC
0.1µF
CLOCK
INPUT
50Ω*
1kΩ
OPTIONAL
0.1µF
100Ω
AD951x
CMOS DRIVER
VCC
50Ω*
1kΩ
1kΩ
AD951x
CMOS DRIVER
OPTIONAL 0.1µF
100Ω
0.1µF
SCLK/DFS
Binary (default)
Twos complement
SDIO/DCS
DCS disabled
DCS enabled (default)
SNR = −20 log (2π × FIN × tJ)
In the equation, the rms aperture jitter (tJ) represents the rootmean-square of all jitter sources, which include the clock input,
analog input signal, and ADC aperture jitter specification. IF
undersampling applications are particularly sensitive to jitter, as
shown in Figure 51.
Figure 49. Single-Ended 1.8 V CMOS Sample Clock
CLOCK
INPUT
Voltage at Pin
AGND
AVDD
05492-051
39kΩ
*50Ω RESISTOR IS OPTIONAL
0.1µF
Table 10. Mode Selection (External Pin Mode)
High speed, high resolution ADCs are sensitive to the quality of
the clock input. The degradation in SNR at a given input
frequency (FIN) due to jitter (tJ) is calculated as
CLK–
0.1µF
The DCS can be enabled or disabled by setting the SDIO/DCS
pin when operating in the external pin mode (see Table 10), or
via the SPI, as described in the Table 15.
JITTER CONSIDERATIONS
CLK+
ADC
AD9233
1kΩ
Jitter in the rising edge of the input is still of paramount
concern and is not reduced by the internal stabilization circuit.
The duty cycle control loop does not function for clock rates
less than 20 MHz nominally. The loop has a time constant
associated with it that needs to be considered in applications
where the clock rate can change dynamically, which requires a
wait time of 1.5 μs to 5 μs after a dynamic clock frequency
increase (or decrease) before the DCS loop is relocked to the
input signal. During the time the loop is not locked, the DCS
loop is bypassed, and the internal device timing is dependant
on the duty cycle of the input clock signal. In such an application,
it can be appropriate to disable the duty cycle stabilizer. In all
other applications, enabling the DCS circuit is recommended to
maximize ac performance.
CLK+
ADC
AD9233
70
0.05ps
05492-052
CLK–
*50Ω RESISTOR IS OPTIONAL
MEASURED
PERFORMANCE
65
Figure 50. Single-Ended 3.3 V CMOS Sample Clock
0.20ps
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to clock duty cycle. Commonly, a ±5% tolerance is
required on the clock duty cycle to maintain dynamic performance characteristics.
The AD9233 contains a DCS that retimes the nonsampling, or
falling edge, providing an internal clock signal with a nominal
50% duty cycle. This allows a wide range of clock input duty
cycles without affecting the performance of the AD9233. Noise
Rev. A | Page 19 of 44
0.5ps
55
1.0ps
50
1.50ps
2.00ps
45
40
2.50ps
3.00ps
1
10
100
INPUT FREQUENCY (MHz)
Figure 51. SNR vs. Input Frequency and Jitter
05492-046
Clock Duty Cycle
SNR (dBc)
60
1000
AD9233
150
400
TOTAL POWER
100
375
50
350
0
25
50
75
100
0
125
05492-034
IDRVDD
325
CLOCK FREQUENCY (MSPS)
Figure 52. AD9233-125 Power and Current vs. Clock Frequency, FIN = 30 MHz
410
200
180
IAVDD
160
370
POWER (mW)
140
×N
350
120
330
100
TOTAL POWER
80
310
60
290
40
250
30
55
80
0
105
CLOCK FREQUENCY (MSPS)
290
150
IAVDD
275
120
260
90
TOTAL POWER
245
60
230
CURRENT (mA)
The data used for Figure 52 and Figure 53 is based on the
same operating conditions as used in the plots in the Typical
Performance Characteristics section with a 5 pF load on each
output driver.
5
Figure 53. AD9233-105 Power and Current vs. Clock Frequency, FIN = 30 MHz
POWER (mW)
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the
Nyquist frequency, fCLK/2. In practice, the DRVDD current is
established by the average number of output bits switching,
which is determined by the sample rate and the characteristics
of the analog input signal. Reducing the capacitive load
presented to the output drivers can minimize digital power
consumption.
20
IDRVDD
05492-082
270
where N is the number of output bits (12 in the case of the
AD9233).
30
IDRVDD
215
0
20
40
CLOCK FREQUENCY (MSPS)
60
0
80
05492-093
2
200
425
390
As shown in Figure 52 and Figure 53, the power dissipated by
the AD9233 is proportional to its sample rate. The digital power
dissipation is determined primarily by the strength of the digital
drivers and the load on each output bit. The maximum DRVDD
current (IDRVDD) can be calculated as
I DRVDD = V DRVDD × C LOAD ×
IAVDD
CURRENT (mA)
450
POWER DISSIPATION AND STANDBY MODE
f CLK
250
CURRENT (mA)
Refer to Application Notes AN-501, Aperture Uncertainty and
ADC System Performance, and AN-756, Sampled Systems and
the Effects of Clock Phase Noise and Jitter for more in-depth
information about jitter performance as it relates to ADCs.
475
POWER (mW)
Treat the clock input as an analog signal in cases where aperture
jitter may affect the dynamic range of the AD9233. Power
supplies for clock drivers should be separated from the ADC
output driver supplies to avoid modulating the clock signal with
digital noise. The power supplies should also not be shared with
analog input circuits such as buffers to avoid the clock
modulating onto the input signal or vice versa. Low jitter,
crystal-controlled oscillators make the best clock sources.
If the clock is generated from another type of source (by
gating, dividing, or other methods), it should be retimed by the
original clock at the last step.
Figure 54. AD9233-80 Power and Current vs. Clock Frequency, FIN = 30 MHz
Rev. A | Page 20 of 44
AD9233
Power-Down Mode
Out-of-Range (OR) Condition
By asserting the PDWN pin high, the AD9233 is placed in
power-down mode. In this state, the ADC typically dissipates
1.8 mW. During power-down, the output drivers are placed in a
high impedance state. Reasserting the PDWN pin low returns
the AD9233 to its normal operational mode. This pin is both
1.8 V and 3.3 V tolerant.
An out-of-range condition exists when the analog input voltage
is beyond the input range of the ADC. OR is a digital output
that is updated along with the data output corresponding to the
particular sampled input voltage. Thus, OR has the same pipeline
latency as the digital data.
Standby Mode
When using the SPI port interface, the user can place the ADC
in power-down or standby modes. Standby mode allows the
user to keep the internal reference circuitry powered when
faster wake-up times are required. See the Memory Map
section for more details.
+FS – 1 LSB
OR
–FS + 1/2 LSB
0000 0000 0001
0000 0000 0000
0000 0000 0000
–FS
–FS – 1/2 LSB
+FS
+FS – 1/2 LSB
05492-041
0
0
1
Figure 55. OR Relation to Input Voltage and Output Data
OR is low when the analog input voltage is within the analog
input range and high when the analog input voltage exceeds the
input range, as shown in Figure 55. OR remains high until the
analog input returns to within the input range and another
conversion is completed. By logically AND’ing the OR bit with
the MSB and its complement, overrange high or underrange
low conditions can be detected. Table 11 is a truth table for the
overrange/underrange circuit in Figure 56, which uses NAND
gates.
MSB
DIGITAL OUTPUTS
OVER = 1
OR
The AD9233 output drivers can be configured to interface with
1.8 V to 3.3 V logic families by matching DRVDD to the digital
supply of the interfaced logic. The output drivers are sized to
provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause current
glitches on the supplies that can affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts can require external buffers or latches.
Table 11. Overrange/Underrange Truth Table
The output data format can be selected for either offset binary
or twos complement by setting the SCLK/DFS pin when
operating in the external pin mode (see Table 10). As detailed in
the Interfacing to High Speed ADCs via SPI User Manual, the
data format can be selected for either offset binary, twos
complement, or Gray code when using the SPI control.
Digital Output Enable Function (OEB)
UNDER = 1
MSB
05492-045
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. The decoupling capacitors on REFT and REFB are
discharged when entering power-down mode and then must be
recharged when returning to normal operation. As a result, the
wake-up time is related to the time spent in power-down mode;
shorter power-down cycles result in proportionally shorter
wake-up times. With the recommended 0.1 μF decoupling
capacitor on REFT and REFB, it takes approximately 0.25 ms
to fully discharge the reference buffer decoupling capacitor and
0.35 ms to restore full operation.
OR DATA OUTPUTS
1 1111 1111 1111
0 1111 1111 1111
0 1111 1111 1110
Figure 56. Overrange/Underrange Logic
OR
0
0
1
1
MSB
0
1
0
1
Analog Input Is:
Within Range
Within Range
Underrange
Overrange
The AD9233 has three-state ability. If the OEB pin is low, the
output data drivers are enabled. If the OEB pin is high, the output
data drivers are placed in a high impedance state. This is not
intended for rapid access to the data bus. Note that OEB is
referenced to the digital supplies (DRVDD) and should not
exceed that supply voltage.
Table 12. Output Data Format
Condition (V)
VIN+ − VIN− < –VREF – 0.5 LSB
VIN+ − VIN− = –VREF
VIN+ − VIN− = 0
VIN+ − VIN− = +VREF – 1.0 LSB
VIN+ − VIN− > +VREF – 0.5 LSB
Binary Output Mode
0000 0000 0000
0000 0000 0000
1000 0000 0000
1111 1111 1111
1111 1111 1111
Twos Complement Mode
1000 0000 0000
1000 0000 0000
0000 0000 0000
0111 1111 1111
0111 1111 1111
Rev. A | Page 21 of 44
Gray Code Mode (SPI Accessible)
1100 0000 0000
1100 0000 0000
0000 0000 0000
1000 0000 0000
1000 0000 0000
OR
1
0
0
0
1
AD9233
TIMING
Data Clock Output (DCO)
The lowest typical conversion rate of the AD9233 is 10 MSPS.
At clock rates below 10 MSPS, dynamic performance can
degrade.
The AD9233 provides a data clock output (DCO) intended for
capturing the data in an external register. The data outputs are
valid on the rising edge of DCO, unless the DCO clock polarity
has been changed via the SPI. See Figure 2 for a graphical
timing description.
The AD9233 provides latched data outputs with a pipeline delay
of 12 clock cycles. Data outputs are available one propagation
delay (tPD) after the rising edge of the clock signal.
The length of the output data lines and the loads placed on
them should be minimized to reduce transients within the
AD9233. These transients can degrade the dynamic performance
of the converter.
Rev. A | Page 22 of 44
AD9233
SERIAL PORT INTERFACE (SPI)
The AD9233 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space provided inside the ADC. This provides the user added
flexibility and customization depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that
are further divided into fields, as documented in the Memory
Map section. For detailed operational information, see the
Interfacing to High Speed ADCs via SPI User Manual.
CONFIGURATION USING THE SPI
As summarized in Table 13, three pins define the SPI of this
ADC. The SCLK/DFS pin synchronizes the read and write data
presented to the ADC. The SDIO/DCS dual-purpose pin allows
data to be sent and read from the internal ADC memory map
registers. The CSB pin is an active low control that enables or
disables the read and write cycles.
Table 13. Serial Port Interface Pins
Mnemonic
SCLK/DFS
SDIO/DCS
CSB
Description
SCLK (Serial Clock) is the serial shift clock in. SCLK
synchronizes serial interface reads and writes.
SDIO (Serial Data Input/Output) is a dual-purpose
pin. The typical role for this pin is an input and
output depending on the instruction being sent
and the relative position in the timing frame.
CSB (Chip Select Bar) is an active low control that
gates the read and write cycles.
The falling edge of the CSB in conjunction with the rising edge
of the SCLK determines the start of the framing. Figure 57 and
Table 14 provide an example of the serial timing and its
definitions.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, permanently enabling the device (this is
called streaming). The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high
during power up, SPI functions are placed in a high impedance
mode. This mode turns on any SPI pin secondary functions. If
CSB is high at power up and then brought low to activate the
SPI, the SPI pin secondary functions are no longer available,
unless the device power is cycled.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase and the length is determined
by the W0 bit and the W1 bit. All data is composed of 8-bit
words. The first bit of each individual byte of serial data indicates
whether a read or write command is issued. This allows the
serial data input/output (SDIO) pin to change direction from
an input to an output.
In addition to word length, the instruction phase determines if
the serial frame is a read or write operation, allowing the serial
port to be used to both program the chip as well as read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB first or in LSB first mode. MSB first is
the default on power up and can be changed via the
configuration register. For more information, see the Interfacing
to High Speed ADCs via SPI User Manual.
Table 14. SPI Timing Diagram Specifications
Name
tDS
tDH
tCLK
tS
tH
tHI
tLO
Description
Setup time between data and rising edge of SCLK
Hold time between data and rising edge of SCLK
Period of the clock
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
HARDWARE INTERFACE
The pins described in Table 13 comprise the physical interface
between the user’s programming device and the serial port of
the AD9233. The SCLK and CSB pins function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during readback.
The SPI interface is flexible enough to be controlled by either
PROM or PIC microcontrollers. This provides the user with the
ability to use an alternate method to program the ADC. One
method is described in detail in the Application Note AN-812.
When the SPI interface is not used, some pins serve a dual
function. When strapped to AVDD or ground during device
power on, the pins are associated with a specific function.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/DCS and SCLK/DFS pins serve as standalone CMOScompatible control pins. When the device is powered up with
the CSB chip select connected to AVDD, the serial port interface is
disabled. In this mode, it is assumed that the user intends to use
the pins as static control lines for the output data format and
duty cycle stabilizer (see Table 10). For more information, see
the Interfacing to High Speed ADCs via SPI User Manual.
Rev. A | Page 23 of 44
AD9233
MEMORY MAP
READING THE MEMORY MAP TABLE
Logic Levels
Each row in the memory map table has eight address locations.
The memory map is roughly divided into three sections: chip
configuration registers map (Address 0x00 to Address 0x02),
device index and transfer registers map (Address 0xFF), and
ADC functions map (Address 0x08 to Address 0x18).
An explanation of two registers follows:
The memory map register in Table 15 displays the register
address number in hexadecimal in the first column. The last
column displays the default value for each hexadecimal address.
The Bit 7 (MSB) column is the start of the default hexadecimal
value given. For example, Hexadecimal Address 0x14,
output_phase has a hexadecimal default value of 0x00. This
means Bit 3 = 0, Bit 2 = 0, Bit 1 = 1, and Bit 0 = 1 or 0011 in
binary. This setting is the default output clock or DCO phase
adjust option. The default value adjusts the DCO phase 90°
relative to the nominal DCO edge and 180° relative to the data
edge. For more information on this function, consult the
Interfacing to High Speed ADCs via SPI User Manual.
•
Bit is set is synonymous with bit is set to Logic 1 or writing
Logic 1 for the bit.
•
Clear a bit is synonymous with bit is set to Logic 0 or
writing Logic 0 for the bit.
SPI-Accessible Features
A list of features accessible via the SPI and a brief description of
what the user can do with these features follows. These features
are described in detail in the Interfacing to High Speed ADCs via
SPI User Manual.
•
Modes: Set either power-down or standby mode.
•
Clock: Access the DCS via the SPI.
•
Offset: Digitally adjust the converter offset.
Open Locations
•
Test I/O: Set test modes to have known data on output bits.
Locations marked as open are currently not supported for this
device. When required, these locations should be written with
0s. Writing to these locations is required only when part of an
address location is open (for example, Address 0x14). If the
entire address location is open (Address 0x13), then the address
location does not need to be written.
•
Output Mode: Setup outputs, vary the strength of the
output drivers.
•
Output Phase: Set the output clock polarity.
•
VREF: Set the reference voltage.
Default Values
Coming out of reset, critical registers are loaded with default
values. The default values for the registers are provided in Table 15.
tDS
tS
tHI
tCLK
tDH
tH
tLO
CSB
SCLK DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
DON’T CARE
05492-053
SDIO DON’T CARE
DON’T CARE
Figure 57. Serial Port Interface Timing Diagram
Rev. A | Page 24 of 44
AD9233
Table 15. Memory Map Register
Addr Parameter
Bit 7
(Hex) Name
(MSB)
Chip Configuration Registers
00
chip_port_config 0
01
chip_id
02
chip_grade
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
First
0 = Off
(Default)
1 = On
Soft
Reset
0 = Off
(Default)
1 = On
1
1
Soft
Reset
0 = Off
(Default)
1 = On
LSB
First
0 = Off
(Default)
1 = On
Bit 0
(LSB)
Default
Value
(Hex)
Default
Notes/
Comments
0
0x18
The nibbles
should be
mirrored. See
Interfacing to
High Speed
ADCs via SPI
User Manual.
Default is
unique chip ID,
different for
each device.
Child ID used
to differentiate
speed grades.
8-Bit Chip ID Bits 7:0
(AD9233 = 0x00), (Default)
ReadOnly
Open
Open
Open
Child ID
0=
125
MSPS,
1=
105
MSPS
Open
Open
Open
ReadOnly
Device Index and Transfer Registers
FF
device_update
Open
Open
Open
Open
Open
Open
Open
SW Transfer
0x00
Synchronously
transfers data
from the
master
shift register to
the slave.
Global ADC Functions
08
modes
Open
Open
PDWN
0—Full
1—
Standby
Open
Open
Internal Power-Down Mode
000—Normal (Power-Up)
001—Full Power-Down
010—Standby
011—Normal (Power-Up)
Note: External PDWN pin
overrides this setting.
0x00
09
Open
Open
Open
Open
Open
Open
0x01
Determines
various generic
modes of chip
operation. See
Power
Dissipation
and Standby
Mode and
SPI-Accessible
Features
sections.
See Clock Duty
Cycle and
SPI-Accessible
Features
sections.
clock
Flexible ADC Functions
10
offset
Open
Digital Offset Adjust <5:0>
011111
011110
011101
…
000010
000001
000000
111111
111110
111101
...
100001
100000
Rev. A | Page 25 of 44
Open
Offset in LSBs
+7 3/4
+7 1/2
+7 1/4
+1/2
+1/4
0
−1/4
−1/2
−3/4
−7 3/4
−8
Duty Cycle
Stabilizer
0—
Disabled
1—Enabled
0x00
Adjustable for
offset inherent
in the
converter.
See SPIAccessible
Features
section.
AD9233
Addr
(Hex)
0D
Parameter
Name
test_io
Bit 7
(MSB)
14
output_mode
16
output_phase
18
VREF
1
Bit 6
Bit 0
(LSB)
Bit 2
Bit 1
Global Output Test Options
000—Off
001—Midscale Short
010— +FS Short
011— −FS Short
100—Checker Board Output
101—PN 23 Sequence
110—PN 9
111—One/Zero Word Toggle
Data Format Select
Output
00—Offset Binary
Data
(Default)
Invert
01—Twos
1=
Complement
Invert
10—Gray Code
Default
Value
(Hex)
0x00
Default
Notes/
Comments
See the
Interfacing to
High Speed
ADCs via SPI
User Manual.
0x00
Configures the
outputs and
the format of
the data and
the output
driver
strength.
See SPIAccessible
Features
section.
See SPIAccessible
Features
section.
Bit 5
PN23
0=
Normal
1=
Reset
Bit 4
PN9
0=
Normal
1=
Reset
Bit 3
Output Driver
Configuration
00 for DRVDD = 3.3 V
10 for DRVDD = 1.8 V
Open
Output
Disable
1—
Disabled
0—
Enabled 1
Open
Open
DCO
Polarity
1 = Inverted
0 = Normal
Internal Reference
Resistor Divider
00—VREF = 1.25 V
01—VREF = 1.5 V
10—VREF = 1.75 V
11—VREF = 2.00 V
Open
Open
Open
Open
Open
Open
0x00
Open
Open
Open
Open
Open
Open
0xC0
External Output Enable (OEB) pin must be high.
Rev. A | Page 26 of 44
AD9233
LAYOUT CONSIDERATIONS
POWER AND GROUND RECOMMENDATIONS
A single PC board ground plane should be sufficient when
using the AD9233. With proper decoupling and smart partitioning of the analog, digital, and clock sections of the board,
optimum performance is easily achieved.
Exposed Paddle Thermal Heat Slug Recommendations
It is required that the exposed paddle on the underside of the
ADC is connected to analog ground (AGND) to achieve the
best electrical and thermal performance of the AD9233. An
exposed, continuous copper plane on the PCB should mate to
the AD9233 exposed paddle, Pin 0. The copper plane should
have several vias to achieve the lowest possible resistive thermal
path for heat dissipation to flow through the bottom of the PCB.
These vias should be solder filled or plugged.
To maximize the coverage and adhesion between the ADC and
PCB, partition the continuous plane by overlaying a silkscreen
on the PCB into several uniform sections. This provides several
tie points between the two during the reflow process. Using one
continuous plane with no partitions only guarantees one tie
point between the ADC and PCB. See Figure 58 for a PCB
layout example. For detailed information on packaging and the
PCB layout of chip scale packages, see Application Note AN-772,
A Design and Manufacturing Guide for the Lead Frame Chip
Scale Package (LFCSP).
SILKSCREEN PARTITION
PIN 1 INDICATOR
05492-054
When connecting power to the AD9233, it is recommended
that two separate supplies be used: one for analog (AVDD, 1.8 V
nominal) and one for digital (DRVDD, 1.8 V to 3.3 V nominal).
If only a single 1.8 V supply is available, then it should be routed
to AVDD first, then tapped off and isolated with a ferrite bead
or filter choke with decoupling capacitors preceding its connection to DRVDD. The user can employ several different
decoupling capacitors to cover both high and low frequencies.
These should be located close to the point of entry at the PC
board level and close to the parts with minimal trace length.
Figure 58. Typical PCB Layout
CML
The CML pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 38.
RBIAS
The AD9233 requires the user to place a 10 kΩ resistor between
the RBIAS pin and ground. This resister sets the master current
reference of the ADC core and should have at least a 1% tolerance.
REFERENCE DECOUPLING
The VREF pin should be externally decoupled to ground with a
low ESR 1.0 μF capacitor in parallel with a 0.1 μF ceramic low
ESR capacitor. In all reference configurations, REFT and REFB
are bypass points provided for reducing the noise contributed
by the internal reference buffer. It is recommended to place an
external 0.1 μF ceramic capacitor across REFT/REFB. While it is
not required to place this 0.1 μF capacitor, the SNR performance
will degrade by approximately 0.1 dB without it. All reference
decoupling capacitors should be placed as close to the ADC as
possible with minimal trace lengths.
Rev. A | Page 27 of 44
AD9233
EVALUATION BOARD
The AD9233 evaluation board provides all of the support
circuitry required to operate the ADC in its various modes and
configurations. The converter can be driven differentially
through a double balun configuration (default) or through the
AD8352 differential driver. The ADC can also be driven in a
single-ended fashion. Separate power pins are provided to
isolate the DUT from the AD8352 drive circuitry. Each input
configuration can be selected by proper connection of various
components. Figure 59 shows the typical bench characterization
setup used to evaluate the ac performance of the AD9233.
Although at least one 1.8 V supply is needed with a 1 A current
capability for AVDD_DUT and DRVDD_DUT, it is recommended that separate supplies be used for analog and digital.
To operate the evaluation board using the AD8352 option, a
separate 5.0 V analog supply is needed. The 5.0 V supply, or
AMP_VDD, should have a 1 A current capability. To operate
the evaluation board using the alternate SPI options, a separate
3.3 V analog supply is needed in addition to the other supplies.
The 3.3 V supply (AVDD_3.3V) should have a 1 A current
capability as well. Solder Jumpers J501, J502, and J505 allow the
user to combine these supplies. See Figure 64 for more details.
It is critical that the signal sources used for the analog input and
clock have very low phase noise (<1 ps rms jitter) to realize the
optimum performance of the converter. Proper filtering of the
analog input signal to remove harmonics and lower the integrated or broadband noise at the input is also necessary to achieve
the specified noise performance.
INPUT SIGNALS
When connecting the clock and analog source, use clean signal
generators with low phase noise, such as Rohde & Schwarz SMHU
or Agilent HP8644 signal generators or the equivalent. Use one
meter long, shielded, RG-58, 50 Ω coaxial cables for making
connections to the evaluation board. Enter the desired frequency
and amplitude for the ADC. Typically, most ADI evaluation
boards can accept a ~2.8 V p-p or 13 dBm sine wave input for
the clock. When connecting the analog input source, it is
recommended to use a multipole, narrow-band, band-pass
filter with 50 Ω terminations. Analog Devices uses TTE®, Allen
Avionics, and K&L® types of band-pass filters. Connect the filter
directly to the evaluation board, if possible.
See Figure 60 to Figure 70 for the complete schematics and
layout diagrams that demonstrate the routing and grounding
techniques that should be applied at the system level.
POWER SUPPLIES
This evaluation board comes with a wall-mountable switching
power supply that provides a 6 V, 2 A maximum output. Simply
connect the supply to the rated 100 V ac to 240 V ac wall outlet
at 47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter
jack that connects to the PCB at P500. Once on the PC board,
the 6 V supply is fused and conditioned before connecting to
five low dropout linear regulators that supply the proper bias to
each of the various sections on the board. When operating the
evaluation board in a nondefault condition, L501, L503, L504,
L508, and L509 can be removed to disconnect the switching
power supply. This enables the user to bias each section of the
board independently. Use P501 to connect a different supply for
each section.
OUTPUT SIGNALS
The parallel CMOS outputs interface directly with Analog
Devices’ standard single-channel FIFO data capture board
(HSC-ADC-EVALB-SC). For more information on the FIFO
boards and their optional settings, visit www.analog.com/FIFO.
WALL OUTLET
100V TO 240V AC
47Hz TO 63Hz
AIN
3.3V
+
–
+
–
+
VDL
GND
AVDD_3.3V
GND
VCC
3.3V
–
GND
3.3V
+
DRVDD_DUT
GND
2.5V
–
GND
–
AD9233
EVALUATION BOARD
CLK
12-BIT
PARALLEL
CMOS
SPI
Figure 59. Evaluation Board Connection
Rev. A | Page 28 of 44
HSC-ADC-EVALB-SC
FIFO DATA
CAPTURE
BOARD
USB
CONNECTION
SPI
PC
RUNNING
ADC
ANALYZER
AND SPI
USER
SOFTWARE
SPI
05492-084
ROHDE & SCHWARZ,
SMHU,
2V p-p SIGNAL
SYNTHESIZER
BAND-PASS
FILTER
+
AMP_VDD
ROHDE & SCHWARZ,
SMHU,
2V p-p SIGNAL
SYNTHESIZER
1.8V
+
–
GND
5.0V
SWITCHING
POWER
SUPPLY
AVDD_DUT
6V DC
2A MAX
AD9233
DEFAULT OPERATION AND JUMPER SELECTION
SETTINGS
SCLK/DFS
Connect the switching power supply that is supplied in the
evaluation kit between a rated 100 V ac to 240 V ac wall outlet
at 47 Hz to 63 Hz and P500.
If the SPI port is in external pin mode, the SCLK/DFS pin sets the
data format of the outputs. If the pin is left floating, the pin is
internally pulled down, setting the default condition to binary.
Connecting JP2 Pin 2 and Pin 3 sets the format to twos
complement. If the SPI port is in serial pin mode, connecting
JP2 Pin 1 and Pin 2 connects the SCLK pin to the on board
SPI circuitry. See the Serial Port Interface (SPI) section for
more details.
VIN
SDIO/DCS
The evaluation board is set up for a double balun configuration
analog input with optimum 50 Ω impedance matching out to
70 MHz. For more bandwidth response, the differential capacitor
across the analog inputs can be changed or removed (see Table 8).
The common mode of the analog inputs is developed from the
center tap of the transformer via the CML pin of the ADC. See
the Analog Input Considerations section for more information.
If the SPI port is in external pin mode, the SDIO/DCS pin acts
to set the duty cycle stabilizer. If the pin is left floating, the pin is
internally pulled up, setting the default condition to DCS enabled.
To disable the DCS, connect JP3 Pin 2 and Pin 3. If the SPI port
is in serial pin mode, connecting JP3 Pin 1 and Pin 2 connects the
SDIO pin to the on-board SPI circuitry. See the Serial Port
Interface (SPI) section for more details.
VREF
ALTERNATIVE CLOCK CONFIGURATIONS
VREF is set to 1.0 V by tying the SENSE pin to ground via
JP507 (Pin 1 and Pin 2). This causes the ADC to operate in
2.0 V p-p full-scale range. A separate external reference option
is also included on the evaluation board. Simply connect JP507
between Pin 2 and Pin 3, connect JP501, and provide an external
reference at E500. Proper use of the VREF options is detailed in
the Voltage Reference section.
A differential LVPECL clock can also be used to clock the ADC
input using the AD9515 (U500). When using this drive option,
the components listed in Table 16 need to be populated.
Consult the AD9515 data sheet for further information.
The following is a list of the default and optional settings or
modes allowed on the AD9233 Rev. A evaluation board.
POWER
RBIAS
RBIAS requires a 10 kΩ (R503) to ground and is used to set the
ADC core bias current.
CLOCK
The default clock input circuitry is derived from a simple
transformer-coupled circuit using a high bandwidth 1:1
impedance ratio transformer (T503) that adds a very low
amount of jitter to the clock path. The clock input is 50 Ω
terminated and ac-coupled to handle single-ended sine wave
inputs. The transformer converts the single-ended input to a
differential signal that is clipped before entering the ADC
clock inputs.
PDWN
To configure the analog input to drive the AD9515 instead of
the default transformer option, the following components need
to be added, removed, and/or changed.
•
Remove R507, R508, C532, and C533 in the default
clock path.
•
Populate R505 with a 0 Ω resistor and C531 in the default
clock path.
•
Populate R511, R512, R513, R515 to R524, U500, R580,
R582, R583, R584, C536, C537, and R586.
If using an oscillator, two oscillator footprint options are also
available (OSC500) to check the performance of the ADC.
JP508 provides the user flexibility in using the enable pin, which
is common on most oscillators. Populate OSC500, R575, R587,
and R588 to use this option.
To enable the power-down feature, connect JP506, shorting the
PDWN pin to AVDD.
CSB
The CSB pin is internally pulled-up, setting the chip into
external pin mode, to ignore the SDIO and SCLK information.
To connect the control of the CSB pin to the SPI circuitry on the
evaluation board, connect JP1 Pin 1 and Pin 2. To set the chip
into serial pin mode and to enable the SPI information on the
SDIO and SCLK pins, tie JP1 low (connect Pin 2 and Pin 3) in
the always enabled mode.
Rev. A | Page 29 of 44
AD9233
ALTERNATIVE ANALOG INPUT DRIVE
CONFIGURATION
This section provides a brief description of the alternative
analog input drive configuration using the AD8352 . When
using this particular drive option, some components need to be
populated as listed in Table 16. For more details on the AD8352
differential driver, including how it works and its optional pin
settings, consult the AD8352 data sheet.
To configure the analog input to drive the AD8352 instead of
the default transformer option, the following components need
to be added, removed and/or changed:
•
Remove C1 and C2 in the default analog input path.
•
Populate R3 and R4 with 200 Ω resistors in the analog
input path.
•
Populate the optional amplifier input path with all
components, except R594, R595, and C502. Note that to
terminate the input path, only one of these components,
(R9, R592, or R590 and R591) should be populated.
•
Populate C529 with a 5 pF capacitor in the analog
input path.
Currently, R561 and R562 are populated with 0 Ω resistors to
allow signal connection. This area allows the user to design a
filter if additional requirements are necessary.
Rev. A | Page 30 of 44
S504
Rev. A | Page 31 of 44
Figure 60. Evaluation Board Schematic, DUT Analog Inputs
DNI
Ampin/
S505
DNI
R8
DNI
R502
50
DNI
GND;3,4,5
SMA200UP
R7
DNI
R560
0
2
RC0603
2
RC0603
C528
0.1UF
C3
DNI
CML
RC0402
R6
DNI
RC0402
R2
0
R11
0
DNI
R9
DNI
1
1
RC0603
2
R12
0
DNI
RC0603
2
R10
0
DNI
C4
0
C5
0
C509
.1UF
4
5
T500
S
4
5
T1
DNI
S
4
5
2
3
6
1
P
T502
DNI
ETC1-1-13
P
3
2
1
3
2
1
CML
RC0402
For amplifier (AD8352):
Install all optional Amp input components.
R590/R591,R9,R592 Only one should be installed at a time.
Remove C1, C2.
Set R3=R4=200 OHM.
DNI
DNI
When using T502, remove T500, T501.
Repalce C1, C2 with 0 ohm resistors.
Remove R3, R4. Place R6, R502,.
1
1
GND;3,4,5
SMA200UP
GND;3,4,5
SMAEDGE
GND;3,4,5
RC060 3
Ampin
Ain/
S503
Ain
SMAEDGE
CC0402
CC0402
S500
RC060 3
CC0402
R590
25
DNI
R591
25
DNI
R1
DNI
RC0402
R592
DNI
S
T501
P
5
C503
.1UF
DNI
C500
.1UF
DNI
R5
0
C2
.1UF
AMPOUT-
R565
DNI
AMPOUT+
RC0402
R597
4.3K
DNI
R596
0
DNI
DNI
2
1
4
RDP
VIN
RDN
5
16
VIP
2
15
U511
VCM
14
6
7
GND
AMPVDD
GND
VON
VCC
8
GND
VOP
VCC
13
AMPVDD
AD8352
DNI
SIGNAL=GND;17
ENB
3
disable
R594
10K
DNI
J500
enable
1
RGP
R598
100
RGN
DNI 3
AMPVDD
C501
0.3PF
R593
0
DNI
R4
25
R3
25
C510
.1UF
9
10
11
12
RC0402
R571
0
R595
10K
DNI
OPTIONAL AMP INPUT
When using R1, remove R3, R4,R6.
Replace R5 with 0.1UF cap
Replace C1, C2 with 0 ohm resistors.
3 ETC1-1-13 4
2
1
C1
.1UF
RC040 2
CC0402
RC0402
RC0402
RC0402
R53 6
R535
C502
.1UF
DNI
R562
0
CML
R561
0
0
0
RC0402
DNI
RC0402
DNI
1
D500
DNI
R567
33
R566
33
3
VIN+
R574
DNI
HSMS281 2
RC040 2
RC0402
C505
.1UF
DNI
C504
.1UF
DNI
DUTAVDD
2
RC0402
RC0402
R563
DNI
HSMS281 2
AMPOUT-
2
VIN-
DUTAVDD
C529
20PF
D501
DNI
AMPOUT+
1
3
VIN-
CC0402
VIN+
05492-058
DOUBLE BALUN / XFMR INPUT
AD9233
SCHEMATICS
RC060 3
RC060 3
C556
0.1UF
CML
R503
10K
TP500
TP504
D1
Figure 61. Evaluation Board Schematic, DUT, VREF, and Digital Output Interface
Rev. A | Page 32 of 44
E500
48
47
CC0402
E X T_ V R E F
45
D0
46
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
DCO
JP502
DNI
CLK
CLK
JP506
DNI
VIN-
VIN+
CC0402
C554
0.1UF
VREF
SENSE
DUTDRVDD
DUTAVDD
CC0603
RC060 3
chip corners
AVDD
AGND
AVDD
AGND
CSB
SCLK/DFS
SDIO/DCS
DRVDD
DRGND
OR
(MSB) D11
D10
C555
0.1UF
DNI
JP501
CC0805
DNI
JP500
3
C553
1.0UF
DUTAVDD
2
JP507
1
R0402
DNI
R501
VREF
R0402
DNI
R500
SENS E
AD9233LFCSP
AGND
D9
CLK+
D8
EPAD
D7
CLKD6
AVDD
AGND
DRVDD
AVDD
DRGND
OEB
D5
DCO
D4
D3
NC
U510
NC
D2
DRGND
D1
DRVDD
(LSB) D0
SENSE
VREF
REFB
REFT
AGND
VIN+
VIN–
AGND
AVDD
CML
RBIAS
PDWN
1
2
3
4
5
6
7
8
9
10
11
12
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
13
DOR
14
TP502
TP501
TP503
DUTDRVDD
DUTAVDD
15
16
17
18
19
20
21
22
23
24
8
10
9
9
RP500 22
RP501 22
RP501 22
RP502 22
1
7
8
8
DCO
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
DOR
7
6
5
16
15
14
13
12
11
16
15
14
13
12
11
10
RP500 22
RP500 22
RP500 22
RP501 22
RP501 22
RP501 22
RP501 22
RP501 22
RP501 22
RP502 22
RP502 22
RP502 22
RP502 22
RP502 22
RP502 22
RP502 22
CSB_DUT
2
3
4
1
2
3
4
5
6
1
2
3
4
5
6
7
1
JP1
VDL
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
3
2
JP2
O10
O7
O6
I7
I6
O0
OUTPUT BUFFER
OE1
I0
OE2
O1
I1
GND1
O2
GND8
O3
I2
VCC1
O4
O5
I3
VCC4
I4
I5
GND2
O8
I8
GND7
O9
I9
GND3
I10
GND6
O11
I11
VCC2
O12
I12
VCC3
O13
GND4
I13
GND5
O14
OE4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SDIO_ODM
O15
3
DUTAVDD
I14
U509
74VCX16224
1
I15
OE3
SCLK_DTP
1
JP3
3
FDOR
FD0
FD1
FD2
FD3
FD4
FD5
FD6
FD7
FD8
FD9
FD10
FD11
FD12
FD13
FIFOCLK
FIFOCLK
FD0
FD1
FD2
FD3
FD4
FD5
FD6
FD7
FD8
FD9
FD10
FD11
FD12
FD13
FDOR
2
J503
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
SCLK_CHA
SDO_CHA
CSB1_CHA
SDI_CHA
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
J503
OUTPUT CONNECTOR
J503
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
05492-059
DUT
AD9233
GND;3,4,5
CLK/
SMAEDGE
S502
GND;3,4,5
CLK
SMAEDGE
S501
R505
49.9
DNI
C530
0.1UF
C531
0.1UF
DNI
CC0402
RC0402
1
1
OPT_CLK
OPT_CLK
R575
0
DNI
OPT_CLK
R504
49.9
CC0402
VCC
R511
DNI
2
RC0603
2
RC0603
R579
DNI
R510
DNI
R512
0
RC0603
RC0603
R576
DNI
R507
0
DNI
0
OE
OE
GND
GND
CB3LV-3C
OUT
R508
8
10
OUT
12 VCC
14
DNI
C511
.1UF
R578
DNI
R577
DNI
R509
0
R506
0
RC0603
RC0603
D502
HSMS2812
2
1
3
C533
0.1UF
C532
0.1UF
CLK
CLK
E501
5
3
2
AD9515
RC0402
DNI
OUT0B
OUT0
NC=27,28
OUT1B
OUT1
AVDD_3P3V;1,4,17,20,21,24,26,29,30
SYNCB
CLKB
CLK
DNI
U500
R586
4.12K
18
19
22
23
R584
240
DNI
R585
100
DNI
R583
240
DNI
R582
100
DNI
C536
0.1UF
DNI
C537
0.1UF
DNI
S0
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
RC060 3
C534
0.1UF
DNI
C535
0.1UF
DNI
E503
E502
CLK
CLK
To use AD9515 (OPT _CLK), remove R507, R508, C533, C532.
Place C531,R505=0.
4
6
3
R580
10K
DNI
T503
R588
10K
DNI
5
1
2
1
AVDD_3P3V
R581
DNI
7
5
3
1
RC0402
OSC500
RC0402
RC0402
DISABLE
RC0402
2
S7
ENABLE
S8
DNI JP508
VREF
6
S0
7
S1
8
S2
9
S3
10
S4
11
S5
12
S6
13
S9
Figure 62. Evaluation Board Schematic, DUT Clock Inputs
S10
RC060 3
14
RC060 3
15
3
RSET
16
RC0402
RC0402
CC0402
CC0402
RC0402
10K
DNI
RC0402
R587
GN D
25
CC0402
RC0402
GND_PAD
RC0402
32
CC0402
31
CC0402
AVDD_3P3V
RC0402
RC0402
Rev. A | Page 33 of 44
33
CC0402
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
R526
DNI
R527
DNI
R525
DNI
R532
DNI
R533
DNI
R534
DNI
R529
DNI
R528
DNI
R530
DNI
R531
DNI
0
0
0
0
0
0
0
0
0
0
0
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
RC0603
R522
R523
R524
R519
R518
R520
R521
R516
R517
R515
R513
0
0
0
0
0
0
0
0
0
0
0
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
RC0603
DNI
AD9515 LOGIC SETUP
AVDD_3P3V R514
DNI
OPT_CLK
XFMR/AD9515
Clock Circuitry
AD9233
05492-057
2
1
S1
DNI
4
3
1
1
SOIC8
DNI
GP1
GP0
VSS
RC0603
2
2
1
GP1
3
GP0
5
MCLR-GP3
7
9
Rev. A | Page 34 of 44
HEADER UP MALE
DNI
J504
E504
5
6
7
8
DNI
GP2
MCLR
PIC12F629
GP4
GP5
VDD
U506
AMPVDD
R559
D505
261
Optional
DNI
4
3
2
1
DNI
3
PICVCC 1
4
2
6
8
10
PICVCC
GP1
GP0
MC LR-GP3
Figure 63. Evaluation Board Schematic, SPI Circuitry
R547
4.7K
DNI
When using PICSPI controlled port, populate R545, R546, R547.
When using PICSPI controlled port, remove R555, R556, R557.
For FIFO controlled port, populate R555, R556, R557.
PIC-HEADER
DNI
CC0603
2
JP509
C557
0.1UF
DNI
R558
4.7K
A V D D _3 P3 V
+5V=PROGRAMMING ONLY=AMPVDD
+3.3V=NORMAL OPERATION=AVDD_3P3V
RC060 3
SPI CIRCUITRY
R545
4.7K
RC0603
DNI
R546
4.7K
RC0603
DNI
RC0603
R555
0
R557
0
R556
0
R549
10K
AVDD_3P3V
R554
0
RC0603
RC0603
RC0603
RC0603
SCLK_CH A
RC0603
SDI_CHA
R548
10K
R550
10K
RC0603
RC0603
CSB1_CHA
U508
6
Y1
5
VCC
4
Y2
6
Y1
5
VCC
4
Y2
NC7WZ16
1
A1
2
GND
3
A2
U507
NC7WZ07
1
A1
2
GND
3
A2
R552
1K
R551
1K
R553
1K
DUTAVDD AVDD_3P3V
RC0603
SDO_CH A
RC0603
REMOVE WHEN USING OR PROGRAMMING PIC (U506)
CSB_DUT
SCLK_DTP
SDIO_ODM
AD9233
RC0603
05492-056
Figure 64. Evaluation Board Schematic, Power Supply Inputs
Rev. A | Page 35 of 44
DUTDRVDDIN
GND
5
P5
6
P6
J502
J501
J505
LC1210
L500
10UH
LC1210
L506
10UH
LC1210
L502
10UH
LC1210
L507
10UH
LC1210
L505
10UH
D504
S2A_RECT
2A
DO-214AA
ACASE
ACASE
ACASE
ACASE
ACASE
Remove L501,L503,L504,L508,L509.
To use optional power connection
GND
GND
AVDD_3P3VIN
9
P9
10
P10
8
P8
VDLIN
GND
AMPVDDIN
DUTAVDDIN
7
P7
C527
10UF
SMDC110F
3
C548
1OUF
6.3V
C552
1OUF
6.3V
C551
1OUF
6.3V
C550
1OUF
6.3V
C549
1OUF
6.3V
C512
0.1UF
AVDD_3P3V
C517
0.1UF
DUTDRVDD
C516
0.1UF
DUTAVDD
C515
0.1UF
VDL
C514
0.1UF
AMPVDD
OPTIONAL POWER CONNECTION
4
P4
2
3
P3
3
GND
1
2
P2
P501
1
P1
7.5V POWER
CON005
2.5MM JACK
P500
4
FER500
CHOKE_COIL
DUTDRVDD
DUTAVDD
VDL
AMPVDD
PWR_IN
CC0603
CC0603
CC0603
CC0603
C573
0.1UF
C569
0.1UF
C564
0.1UF
C567
0.1UF
R589
261
C572
0.1UF
C575
0.1UF
C565
0.1UF
CC0603
CC0603
CC0603
CC0603
C524
1UF
PWR_IN
C521
1UF
PWR_IN
C519
1UF
PWR_IN
CC0603
C599
0.1UF
CC0603
0.1UF
C570
0.1UF
4
4
4
CC0603
2
O UTP U T1
OUTPUT4
CC0603
C559
CC0603
C566
0.1UF
IN P U T
C558
CC0603
2
O UTP U T1
OUTPUT4
U504
ADP3339AKC-3.3
IN P U T
U503
ADP3339AKC-2.5
2
O UTP U T1
OUTPUT4
U502
ADP3339AKC-1.8
IN P U T
0.1UF
C568
0.1UF
3
3
3
GND
1
GND
1
GND
1
C574
0.1UF
CC0402
C540
0.1UF
CC0402
C545
0.1UF
VDLIN
CC0402
CC0402
C513
1UF
PWR_IN
C523
1UF
PWR_IN
DUTDRVDDIN
DUTAVDDIN
TP508
TP505
AVDD_3P3V
LC1210
L508
10UH
LC1210
L503
10UH
AVDD_3P3V
C526
1UF
C520
1UF
C518
1UF
L504
10UH
LC1210
TP506
C539
0.1UF
C544
0.1UF
3
3
O UTP U T1
OUTPUT4
CC0402
CC0402
INP UT
C542
0.1UF
C546
0.1UF
CC0402
CC0402
C538
0.1UF
C543
0.1UF
O U TP UT 1
OUTPUT4
U505
ADP3339AKC-3.3
INP UT
U501
ADP3339AKC-5
DUTAVDD=1.8V
DUTDRVDD=2.5V
VDL=3.3V
AMPVDD=5V
AVDD_3.3V=3.3V
GND
1
GND
1
F500
D503
3A
SHOT_RECT
DO-214AB
2
2
LC1210
L509
10UH
LC1210
L501
10UH
C525
1UF
C522
1UF
TEST POINTS
GROUND
4
4
TP510
2
TP512
CR500
TP511
1
TP509
Power Supply Input
6V, 2A max
H503
H502
Connected to Ground
Mounting Holes
H500
H501
AVDD_3P3V
AMPVDDIN
TP513
TP507
AD9233
05492-055
AD9233
05492-063
EVALUATION BOARD LAYOUTS
05492-062
Figure 65. Evaluation Board Layout, Primary Side
Figure 66. Evaluation Board Layout, Secondary Side (Mirrored Image)
Rev. A | Page 36 of 44
05492-065
AD9233
05492-064
Figure 67. Evaluation Board Layout, Ground Plane
Figure 68. Evaluation Board Layout, Power Plane
Rev. A | Page 37 of 44
05492-061
AD9233
05492-060
Figure 69. Evaluation Board Layout, Silkscreen Primary Side
Figure 70. Evaluation Board Layout, Silkscreen Secondary Side (Mirrored Image)
Rev. A | Page 38 of 44
AD9233
BILL OF MATERIALS (BOM)
Table 16. Evaluation Board BOM
Item
1
2
Qty.
1
24
Omit
(DNI)
3
4
5
10
6
7
8
9
10
1
1
5
1
15
11
1
Reference Designator
AD9246CE_REVA
C1, C2, C509, C510, C511, C512,
C514, C515, C516, C517, C528, C530,
C532, C533, C538, C539, C540, C542,
C543, C544, C545, C546, C554, C555
C3, C500, C502, C503, C504, C505,
C531, C534, C535, C536, C537, C557
C501
C4, C5
C513, C518, C519, C520, C521,
C522, C523, C524, C525, C526
C527
C529
C548, C549, C550, C551, C552
C553
C556, C558, C559, C564, C565,
C566, C567, C568, C569, C570,
C572, C573, C574, C575, C599
CR500
12
1
D502
Diode
SOT-23
30 V, 20 mA,
dual Schottky
13
1
D500, D501
D503
Diodes
Diode
DO-214AB
3 A, 30 V, SMC
14
1
D504
Diode
DO-214AA
2 A, 50 V, SMC
15
16
1
D505
F500
LED
Fuse
LN1461C
1210
AMB
6.0 V, 2.2 A trip
current resettable
fuse
17
1
FER500
Choke
2020
J500
J501, J502, J505
J503
Jumper
Jumpers
Connector
120 Pin
Solder jumper
Solder jumper
Male header
Connector
Jumpers
10 Pin
3 Pin
Male, 2 × 5
Male, straight
12
1
2
2
18
19
20
1
1
3
1
1
Device
PCB
Capacitors
Package
0402
Description
PCB
0.1 μF
Capacitor
Resistors
Capacitors
0402
0402
0402
0.3 pF
0Ω
1.0 μF
Capacitor
Capacitor
Capacitors
Capacitor
Capacitors
1206
0402
ACASE
0805
0603
10 μF
20 pF
10 μF
1.0 μF
0.1 μF
LED
0603
Green
3
J504
JP1, JP2, JP3
23
4
JP500, JP501, JP502, JP506
Jumpers
2 Pin
Male, straight
24
1
JP507
Jumpers
3 Pin
Male, straight
25
10
JP508, JP509
L500, L501, L502, L503, L504,
L505, L506, L507, L508, L509
Ferrite Beads
1
OSC500
Oscillator
3.2 mm ×
2.5 mm ×
1.6 mm
SMT
1
P500
P501
Connector
Connector
PJ-102A
10 Pin
26
27
28
1
Rev. A | Page 39 of 44
Panasonic
LNJ314G8TRA
HSMS2812
Micro Commercial Group
SK33-TPMSCT-ND
Micro Commercial Group
S2A-TPMSTR-ND
Amber LED
Tyco, Raychem
NANO SMDC110F-2
Murata
DLW5BSN191SQ2
21
22
2
Supplier/Part No.
Analog Devices, Inc.
Samtec
TSW-140-08-G-T-RA
Samtec
Samtec
TSW-103-07-G-S
Samtec
TSW-102-07-G-S
Samtec
TSW-103-07-G-S
Digi-Key P9811CT-ND
125 MHz or
105 MHz
DC power jack
Male, straight
CTS Reeves CB3LV-3C
Digi-Key CP-102A-ND
PTMICRO10
AD9233
Item
29
30
Qty.
Omit
(DNI)
6
Package
0402
0402
Description
DNI
0Ω
0402
0603
0402
0603
0603
25 Ω
DNI
DNI
10 kΩ
49.9 Ω
0603
0Ω
Resistors
Resistors
Resistors
0603
0603
0603
4.7 kΩ
1 kΩ
261 Ω
Resistors
Resistors
Resistors
Resistor
Resistors
Resistors
Resistor
Resistors
Resistors
Resistor
Resistor
Resistors
Switch
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
RCA74204
RCA74208
S500, S501
Connectors
SMAEDGE
33 Ω
100 Ω
240 Ω
4.12 kΩ
10 kΩ
25 Ω
DNI
0Ω
10 kΩ
4.3 kΩ
22 Ω
22 Ω
Momentary
(normally open)
SMA edge
right angle
2
2
S502, S503
S504, S505
Connectors
SMA200UP
T500, T501
T1
T503
Transformers
SM-22
M/A-Com ETC1-1-13
1
Transformer
CD542
Mini-Circuits
ADT1-1WT
T502
U500
IC
32-Lead
LFCSP
Clock distribution
Analog Devices, Inc.
AD9515BCPZ
Analog Devices, Inc.
ADP3339AKCZ-5
Analog Devices, Inc.
ADP3339AKCZ-1.8
Analog Devices, Inc.
ADP3339AKCZ-2.5
Analog Devices, Inc.
ADP3339AKCZ-3.3
5
6
31
32
33
34
35
2
6
6
4
1
1
36
9
23
37
38
39
4
3
1
1
40
41
42
43
44
45
46
47
48
49
50
51
52
2
53
2
3
2
1
3
2
1
2
2
1
1
2
1
54
55
56
2
1
1
1
57
Reference Designator
R1, R6, R563, R565, R574, R577
R2, R5, R561, R562, R571
R10, R11, R12, R535, R536, R575
R3, R4
R7, R8, R9, R502, R510, R511
R500, R501, R576, R578, R579, R581
R503, R548, R549, R550
R504
R505
R506, R508, R509, R512, R554,
R555, R556, R557, R560
R507, R514, R513, R515, R516, R517,
R518, R519, R520, R521, R522, R523,
R524, R525, R526, R527, R528, R529,
R530, R531, R532, R533, R534
R545, R546, R547, R558
R551, R552, R553
R589
R559
R566, R567
R582, R585, R598
R583, R584
R586
R580, R587, R588
R590, R591
R592
R593, R596
R594, R595
R597
RP500
RP501, RP502
S1
Device
Resistors
Resistors
Resistors
Resistors
Resistors
Resistors
Resistors
Resistor
Resistor
Resistors
Panasonic
EVQ-PLDA15
SMA RF
5-pin upright
58
1
U501
IC
SOT-223
Voltage regulator
59
1
U502
IC
SOT-223
Voltage regulator
60
1
U503
IC
SOT-223
Voltage regulator
61
2
U504, U505
ICs
SOT-223
Voltage regulator
Rev. A | Page 40 of 44
Supplier/Part No.
AD9233
Item
62
Qty.
63
64
65
66
Reference Designator
U506
Device
IC
Package
8-pin SOIC
1
1
1
U507
U508
U509
IC
IC
IC
1
U510
DUT
(AD9233)
IC
SC70
SC70
48-Lead
TSSOP
48-Lead
LFCSP
16-Lead
LFCSP
67
Total
Omit
(DNI)
1
1
128
U511 (or Z500)
107
Rev. A | Page 41 of 44
Description
8-bit
microcontroller
Dual buffer
Dual buffer
Buffer/line driver
Supplier/Part No.
Microchip PIC12F629
ADC
Analog Devices, Inc.
AD9233BCPZ
Analog Devices, Inc.
AD8352ACPZ
Differential
amplifier
Fairchild NC7WZ16
Fairchild NC7WZ07
Fairchild 74VCX162244
AD9233
OUTLINE DIMENSIONS
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
36
PIN 1
INDICATOR
TOP
VIEW
12° MAX
48
PIN 1
INDICATOR
1
EXPOSED
PAD
6.75
BSC SQ
4.25
4.10 SQ
3.95
(BOTTOM VIEW)
0.50
0.40
0.30
1.00
0.85
0.80
0.30
0.23
0.18
25
24
12
13
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 71. 48-Lead Frame Chip Scale Package [LFCSP_VQ]
7 mm × 7 mm Body, Very Thin Quad
(CP-48-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9233BCPZ-125 2
AD9233BCPZRL7–1252
AD9233BCPZ-1052
AD9233BCPZRL7–1052
AD9233BCPZ-802
AD9233BCPZRL7–802
AD9233-125EB
AD9233-105EB
AD9233-80EB
1
2
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
48-Lead Lead Frame Chip Scale Package [LFSCP_VQ]
Evaluation Board
Evaluation Board
Evaluation Board
It is required that the exposed paddle be soldered to the AGND plane to achieve the best electrical and thermal performance .
Z = Pb-free part.
Rev. A | Page 42 of 44
Package Option 1
CP-48-3
CP-48-3
CP-48-3
CP-48-3
CP-48-3
CP-48-3
AD9233
NOTES
Rev. A | Page 43 of 44
AD9233
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05492-0-8/06(A)
Rev. A | Page 44 of 44