PDF Data Sheet Rev. B

FEATURES
FUNCTIONAL BLOCK DIAGRAM
Low phase noise phase-locked loop core
Reference input frequencies to 250 MHz
Programmable dual modulus prescaler
Programmable charge pump (CP) current
Separate CP supply (VCPS) extends tuning range
Two 1.6 GHz, differential clock inputs
8 programmable dividers, 1 to 32, all integers
Phase select for output-to-output coarse delay adjust
4 independent 1.2 GHz LVPECL outputs
Additive output jitter of 225 fs rms
4 independent 800 MHz low voltage differential signaling
(LVDS) or 250 MHz complementary metal oxide conductor
(CMOS) clock outputs
Additive output jitter of 275 fs rms
Fine delay adjust on 2 LVDS/CMOS outputs
Serial control port
Space-saving 64-lead LFCSP
VS
GND
RSET
CPRSET VCP
DISTRIBUTION
REF
REFIN
R DIVIDER
REFINB
N DIVIDER
FUNCTION
AD9510
PHASE
FREQUENCY
DETECTOR
SYNCB,
RESETB
PDB
PLL
REF
CHARGE
PUMP
PLL
SETTINGS
CLK1
CP
STATUS
CLK2
CLK1B
CLK2B
PROGRAMMABLE
DIVIDERS AND
PHASE ADJUST
LVPECL
OUT0
/1, /2, /3... /31, /32
OUT0B
LVPECL
OUT1
/1, /2, /3... /31, /32
OUT1B
LVPECL
OUT2
/1, /2, /3... /31, /32
OUT2B
SCLK
SDIO
SDO
LVPECL
SERIAL
CONTROL
PORT
OUT3
/1, /2, /3... /31, /32
OUT3B
CSB
LVDS/CMOS
OUT4
/1, /2, /3... /31, /32
OUT4B
APPLICATIONS
LVDS/CMOS
Low jitter, low phase noise clock distribution
Clocking high speed ADCs, DACs, DDSs, DDCs, DUCs, and
mixed-signal front ends (MxFEs)
High performance wireless transceivers
High performance instrumentation
Broadband infrastructure
/1, /2, /3... /31, /32
∆T
/1, /2, /3... /31, /32
∆T
OUT5
OUT5B
LVDS/CMOS
OUT6
OUT6B
LVDS/CMOS
/1, /2, /3... /31, /32
OUT7
OUT7B
05046-001
Data Sheet
1.2 GHz Clock Distribution IC, PLL Core,
Dividers, Delay Adjust, Eight Outputs
AD9510
Figure 1.
GENERAL DESCRIPTION
The AD9510 provides a multi-output clock distribution function
along with an on-chip phase-locked loop (PLL) core. The design
emphasizes low jitter and phase noise to maximize data converter
performance. Other applications with demanding phase noise
and jitter requirements also benefit from this device.
The PLL section consists of a programmable reference divider
(R); a low noise, phase frequency detector (PFD); a precision
charge pump (CP); and a programmable feedback divider (N).
By connecting an external voltage-controlled crystal oscillator
(VCXO) or voltage-controlled oscillator (VCO) to the CLK2
and CLK2B pins, frequencies of up to 1.6 GHz can be synchronized
to the input reference.
There are eight independent clock outputs. Four outputs are low
voltage positive emitter-coupled logic (LVPECL) at 1.2 GHz,
and four are selectable as either LVDS (800 MHz) or CMOS
(250 MHz) levels.
Rev. B
Each output has a programmable divider that can be bypassed
or set to divide by any integer up to 32. The phase of one clock
output relative to another clock output can be varied by means
of a divider phase select function that serves as a coarse timing
adjustment. Two of the LVDS/CMOS outputs feature programmable delay elements with full-scale ranges up to 8 ns of delay.
This fine tuning delay block has 5-bit resolution, giving 25
possible delays from which to choose for each full-scale setting
(Register 0x36 and Register 0x3A = 00000b to 11000b).
The AD9510 is ideally suited for data converter clocking
applications where maximum converter performance is
achieved by encode signals with subpicosecond jitter.
The AD9510 is available in a 64-lead LFCSP and can be operated
from a single 3.3 V supply. An external VCO, which requires an
extended voltage range, can be accommodated by connecting
the charge pump supply (VCP) to 5.5 V. The temperature range
is −40°C to +85°C.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9510
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Overall ......................................................................................... 28
Applications ....................................................................................... 1
PLL Section ................................................................................. 28
Functional Block Diagram .............................................................. 1
FUNCTION Pin ......................................................................... 32
General Description ......................................................................... 1
Distribution Section ................................................................... 32
Revision History ............................................................................... 2
CLK1 and CLK2 Clock Inputs.................................................. 32
Specifications..................................................................................... 4
Dividers........................................................................................ 32
PLL Characteristics ...................................................................... 4
Delay Block ................................................................................. 37
Clock Inputs .................................................................................. 5
Outputs ........................................................................................ 37
Clock Outputs ............................................................................... 6
Power-Down Modes .................................................................. 38
Timing Characteristics ................................................................ 6
Reset Modes ................................................................................ 38
Clock Output Phase Noise .......................................................... 8
Single-Chip Synchronization .................................................... 39
Clock Output Additive Time Jitter ........................................... 11
Multichip Synchronization ....................................................... 39
PLL and Distribution Phase Noise and Spurious ................... 13
Serial Control Port ......................................................................... 40
Serial Control Port ..................................................................... 13
Serial Control Port Pin Descriptions ....................................... 40
FUNCTION Pin ......................................................................... 14
General Operation of Serial Control Port ............................... 40
STATUS Pin ................................................................................ 14
The Instruction Word (16 Bits) ................................................ 41
Power ............................................................................................ 15
MSB/LSB First Transfers ........................................................... 41
Timing Diagrams ............................................................................ 16
Register Map and Description ...................................................... 44
Absolute Maximum Ratings.......................................................... 17
Summary Table ........................................................................... 44
Thermal Characteristics ............................................................ 17
Register Map Description ......................................................... 46
ESD Caution ................................................................................ 17
Power Supply ................................................................................... 53
Pin Configuration and Function Descriptions ........................... 18
Power Management ................................................................... 53
Typical Performance Characteristics ........................................... 20
Applications Information .............................................................. 54
Terminology .................................................................................... 24
Using the AD9510 Outputs for ADC Clock Applications .... 54
Typical Modes of Operation.......................................................... 25
CMOS Clock Distribution ........................................................ 54
PLL with External VCXO/VCO Followed by Clock
Distribution ................................................................................. 25
LVPECL Clock Distribution ..................................................... 55
Clock Distribution Only ............................................................ 25
Power and Grounding Considerations and Power Supply
Rejection ...................................................................................... 55
LVDS Clock Distribution .......................................................... 55
PLL with External VCO and Band-Pass Filter Followed by
Clock Distribution...................................................................... 26
Outline Dimensions ....................................................................... 56
Functional Description .................................................................. 28
Ordering Guide .......................................................................... 56
REVISION HISTORY
9/13—Rev. A to Rev. B
Changes to General Description Section ...................................... 1
Changes to Table 4 ............................................................................ 6
Changes to Table 6 .......................................................................... 11
Added Table 13; Renumbered Sequentially ................................ 17
Changes to Figure 6 ........................................................................ 18
Added EPAD Row, Table 14 .......................................................... 19
Changes to Figure 21 ...................................................................... 22
Changes to Delay Block Section, Figure 40, and Calculating the
Delay Section................................................................................... 37
Changes to Address 0x36[5:1] and Address 0x3A[5:1],
Table 24 ............................................................................................ 44
Changes to Address 0x36 and Address 0x3A, Table 25 ............. 49
Updated Outline Dimensions ....................................................... 56
Changes to Ordering Guide .......................................................... 56
Rev. B | Page 2 of 56
Data Sheet
AD9510
5/05—Rev. 0 to Rev. A
Changes to Features .......................................................................... 1
Changes to Table 1 and Table 2 ....................................................... 5
Changes to Table 4 ............................................................................ 8
Changes to Table 5 ............................................................................ 9
Changes to Table 6 ..........................................................................14
Changes to Table 8 and Table 9 .....................................................15
Changes to Table 11 ........................................................................16
Changes to Table 13 ........................................................................20
Changes to Figure 7 and Figure 10 ...............................................22
Changes to Figure 19 to Figure 23 ................................................24
Changes to Figure 30 and Figure 31 .............................................26
Changes to Figure 32 ......................................................................27
Changes to Figure 33 ......................................................................28
Changes to VCO/VCXO Clock Input—CLK2 Section ..............29
Changes to A and B Counters Section .........................................30
Changes to PLL Digital Lock Detect Section ..............................31
Changes to PLL Analog Lock Detect Section ..............................32
Changes to Loss of Reference Section ..........................................32
Changes to FUNCTION Pin Section ...........................................33
Changes to RESETB: 58h<6:5> = 00b (Default) Section ...........33
Changes to SYNCB: 58h<6:5> = 01b Section ..............................33
Changes to CLK1 and CLK2 Clock Inputs Section ....................33
Changes to Calculating the Delay Section ................................... 38
Changes to Soft Reset via the Serial Port Section ....................... 41
Changes to Multichip Synchronization Section.......................... 41
Changes to Serial Control Port Section ....................................... 42
Changes to Serial Control Port Pin Descriptions Section ......... 42
Changes to General Operation of Serial
Control Port Section ....................................................................... 42
Added Framing a Communication Cycle with CSB Section .... 42
Added Communication Cycle—Instruction Plus
Data Section ..................................................................................... 42
Changes to Write Section ............................................................... 42
Changes to Read Section ................................................................ 42
Changes to The Instruction Word (16 Bits) Section .................. 43
Changes to Table 20 ........................................................................ 43
Changes to MSB/LSB First Transfers Section ............................. 43
Changes to Table 21 ........................................................................ 44
Added Figure 52; Renumbered Sequentially ............................... 45
Changes to Table 23 ........................................................................ 46
Changes to Table 24 ........................................................................ 49
Changes to Using the AD9510 Outputs for ADC Clock
Applications ..................................................................................... 57
4/05—Revision 0: Initial Version
Rev. B | Page 3 of 56
AD9510
Data Sheet
SPECIFICATIONS
Typical (typ) is given for VS = 3.3 V ± 5%, VS ≤ VCPS ≤ 5.5 V, TA = 25°C, RSET = 4.12 kΩ, CPRSET = 5.1 kΩ, unless otherwise noted.
Minimum (min) and maximum (max) values are given over full VS and TA (−40°C to +85°C) variation.
PLL CHARACTERISTICS
Table 1.
Parameter
REFERENCE INPUTS (REFIN)
Input Frequency
Input Sensitivity
Self-Bias Voltage, REFIN
Self-Bias Voltage, REFINB
Input Resistance, REFIN
Input Resistance, REFINB
Input Capacitance
PHASE FREQUENCY DETECTOR (PFD)
PFD Input Frequency
PFD Input Frequency
PFD Input Frequency
Antibacklash Pulse Width
Antibacklash Pulse Width
Antibacklash Pulse Width
CHARGE PUMP (CP)
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
CPRSET Range
ICP Three-State Leakage
Sink-and-Source Current Matching
ICP vs. VCP
ICP vs. Temperature
RF CHARACTERISTICS (CLK2) 2
Input Frequency
Input Sensitivity
Input Common-Mode Voltage, VCM
Input Common-Mode Range, VCMR
Input Sensitivity, Single-Ended
Input Resistance
Input Capacitance
CLK2 VS. REFIN DELAY
PRESCALER (PART OF N DIVIDER)
Prescaler Input Frequency
P = 2 DM (2/3)
P = 4 DM (4/5)
P = 8 DM (8/9)
P = 16 DM (16/17)
P = 32 DM (32/33)
CLK2 Input Frequency for PLL
Min
Typ
0
1.45
1.40
4.0
4.5
150
1.60
1.50
4.9
5.4
2
Max
Unit
250
MHz
mV p-p
V
V
kΩ
kΩ
pF
1.75
1.60
5.8
6.3
100
100
45
1.5
1.3
1.3
2.9
6.0
MHz
MHz
MHz
ns
ns
ns
4.8
0.60
2.5
2.7/10
1
2
1.5
2
mA
mA
%
kΩ
nA
%
%
%
150
1.6
1.6
GHz
1.7
1.8
mV p-p
V
V
mV p-p
150
4.0
4.8
2
500
5.6
600
1000
1600
1600
1600
300
kΩ
pF
ps
MHz
MHz
MHz
MHz
MHz
MHz
Rev. B | Page 4 of 56
Test Conditions/Comments
Self-bias voltage of REFIN 1
Self-bias voltage of REFINB1
Self-biased1
Self-biased1
Antibacklash pulse width, Register 0x0D[1:0] = 00b
Antibacklash pulse width, Register 0x0D[1:0] = 01b
Antibacklash pulse width, Register 0x0D[1:0] = 10b
Register 0x0D[1:0] = 00b (this is the default setting)
Register 0x0D[1:0] = 01b
Register 0x0D[1:0] = 10b
Programmable
With CPRSET = 5.1 kΩ
VCP = VCPS/2
0.5 < VCP < VCPS − 0.5 V
0.5 < VCP < VCPS − 0.5 V
VCP = VCPS/2 V
Frequencies > 1200 MHz (LVPECL) or 800 MHz (LVDS)
require a minimum divide-by-2 (see the Distribution
Section)
Self-biased, enables ac coupling
With 200 mV p-p signal applied
CLK2 ac-coupled, CLK2B capacitively bypassed to RF
ground
Self-biased
Difference at PFD
See the VCO/VCXO Feedback Divider—N (P, A, B) section
A, B counter input frequency
Data Sheet
AD9510
Parameter
NOISE CHARACTERISTICS
In-Band Noise of the Charge Pump/
Phase Frequency Detector (In-Band
Means Within the LBW of the PLL)
At 50 kHz PFD Frequency
At 2 MHz PFD Frequency
At 10 MHz PFD Frequency
At 50 MHz PFD Frequency
PLL Figure of Merit
Min
Typ
Max
Unit
Test Conditions/Comments
Synthesizer phase noise floor estimated by measuring
the in-band phase noise at the output of the VCO and
subtracting 20logN (where N is the N divider value)
−172
−156
−149
−142
−218 +
10 × log
(fPFD)
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
3.5
7.5
3.5
ns
ns
ns
7
15
11
ns
ns
ns
PLL DIGITAL LOCK DETECT WINDOW 4
Required to Lock (Coincidence of Edges)
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
To Unlock After Lock (Hysteresis)4
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
Approximation of the PFD/CP phase noise floor (in the
flat region) inside the PLL loop bandwidth; when
running closed loop this phase noise is gained up
by 20 × log(N) 3
Signal available at STATUS pin when selected by
Register 0x08[5:2]
Selected by Register 0x0D
Bit[5] = 1b.
Bit[5] = 0b.
Bit[5] = 0b.
Selected by Register 0x0D
Bit[5] = 1b.
Bit[5] = 0b.
Bit[5] = 0b.
REFIN and REFINB self-bias points are offset slightly to avoid chatter on an open input condition.
CLK2 is electrically identical to CLK1; the distribution-only input can be used as differential or single-ended input (see the Clock Inputs section).
Example: −218 + 10 × log(fPFD) + 20 × log(N) gives the values for the in-band noise at the VCO output.
4
For reliable operation of the digital lock detect, the period of the PFD frequency must be greater than the unlock-after-lock time.
1
2
3
CLOCK INPUTS
Table 2.
Parameter
CLOCK INPUTS (CLK1, CLK2) 1
Input Frequency
Input Sensitivity
Symbol
Min
Typ
0
Unit
1.6
GHz
mV p-p
150 2
Input Level
Input Common-Mode Voltage
Input Common-Mode Range
Input Sensitivity, Single-Ended
Input Resistance
Input Capacitance
Max
VCM
VCMR
1.5
1.3
4.0
1.6
150
4.8
2
23
V p-p
1.7
1.8
V
V
mV p-p
kΩ
pF
5.6
Test Conditions/Comments
Jitter performance can be improved with higher slew
rates (greater swing)
Larger swings turn on the protection diodes and can
degrade jitter performance
Self-biased; enables ac coupling
With 200 mV p-p signal applied; dc-coupled
CLK2 ac-coupled, CLK2B ac-bypassed to RF ground
Self-biased
CLK1 and CLK2 are electrically identical; each can be used as either a differential or a single-ended input.
With a 50 Ω termination, this is −12.5 dBm.
3
With a 50 Ω termination, this is +10 dBm.
1
2
Rev. B | Page 5 of 56
AD9510
Data Sheet
CLOCK OUTPUTS
Table 3.
Parameter
LVPECL CLOCK OUTPUTS
OUT0, OUT1, OUT2, OUT3;
Differential
Output Frequency
Output High Voltage
Output Low Voltage
Output Differential Voltage
LVDS CLOCK OUTPUTS
OUT4, OUT5, OUT6, OUT7;
Differential
Output Frequency
Differential Output Voltage
Delta VOD
Output Offset Voltage
Delta VOS
Short-Circuit Current
CMOS CLOCK OUTPUTS
OUT4, OUT5, OUT6, OUT7
Output Frequency
Output Voltage High
Output Voltage Low
Symbol
Min
Typ
Max
Unit
VOH
VOL
VOD
VS − 1.22
VS − 2.10
660
VS − 0.98
VS − 1.80
810
1200
VS − 0.93
VS − 1.67
965
MHz
V
V
mV
VOD
250
360
VOS
1.125
1.23
ISA, ISB
800
450
25
1.375
25
24
14
250
VOH
VOL
VS − 0.1
0.1
MHz
mV
mV
V
mV
mA
MHz
V
V
Test Conditions/Comments
Termination = 50 Ω to VS − 2 V
Output level Register 0x3C, Register 0x3D,
Register 0x3E, Register 0x3F[3:2] = 10b
See Figure 21
Termination = 100 Ω differential; default
Output level Register 0x40, Register 0x41,
Register 0x42, Register 0x43[2:1] = 01b
3.5 mA termination current
See Figure 22
Output shorted to GND
Single-ended measurements, B outputs:
inverted, termination open
With 5 pF load each output, see Figure 23
At 1 mA load
At 1 mA load
TIMING CHARACTERISTICS
Table 4.
Parameter
LVPECL
Symbol
Output Rise Time
Output Fall Time
PROPAGATION DELAY, CLK-TO-LVPECL OUT 1
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, LVPECL OUTPUTS
OUT1 to OUT0 on Same Part 2
OUT2 to OUT3 on Same Part2
All LVPECL OUTs on Same Part2
All LVPECL OUTs Across Multiple Parts 3
Same LVPECL OUT Across Multiple
Parts3
LVDS
tRP
tFP
tPECL
Output Rise Time
Output Fall Time
tSKP
tSKP
tSKP
tSKP_AB
tSKP_AB
tRL
tFL
Min
Typ
Max
Unit
130
130
180
180
ps
ps
335
375
490
545
0.5
635
695
ps
ps
ps/°C
−5
15
90
+30
45
130
+85
80
180
275
130
ps
ps
ps
ps
ps
200
210
350
350
Rev. B | Page 6 of 56
ps
ps
Test Conditions/Comments
Termination = 50 Ω to VS − 2 V; output level
Register 0x3C, Register 0x3D, Register 0x3E,
Register 0x3F[3:2] = 10b
20% to 80%, measured differentially
80% to 20%, measured differentially
Termination = 100 Ω differential; output level
Register 0x40, Register 0x41, Register 0x42,
Register 0x43[2:1] = 01b; 3.5 mA termination
current
20% to 80%, measured differentially
80% to 20%, measured differentially
Data Sheet
Parameter
PROPAGATION DELAY, CLK-TO-LVDS OUT1
OUT4, OUT5, OUT6, OUT7
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, LVDS OUTPUTS
OUT4 to OUT7 on Same Part2
OUT5 to OUT6 on Same Part2
All LVDS OUTs on Same Part2
All LVDS OUTs Across Multiple Parts3
Same LVDS OUT Across Multiple Parts3
CMOS
Output Rise Time
Output Fall Time
PROPAGATION DELAY, CLK-TO-CMOS OUT1
Divide = Bypass
Divide = 2 − 32
Variation with Temperature
OUTPUT SKEW, CMOS OUTPUTS
All CMOS OUTs on Same Part2
All CMOS OUTs Across Multiple Parts3
Same CMOS OUT Across Multiple Parts3
LVPECL-TO-LVDS OUT
Output Skew
LVPECL-TO-CMOS OUT
Output Skew
LVDS-TO-CMOS OUT
Output Skew
DELAY ADJUST 4
Shortest Delay Range 5
Zero Scale
Full Scale
Linearity, DNL
Linearity, INL
Longest Delay Range5
Zero Scale
Full Scale
Linearity, DNL
Linearity, INL
Delay Variation with Temperature
Long Delay Range, 8 ns 6
Zero Scale
Full Scale
Short Delay Range, 1 ns6
Zero Scale
Full Scale
AD9510
Symbol
tLVDS
Min
Typ
Max
Unit
0.99
1.04
1.33
1.38
0.9
1.59
1.64
ns
ns
ps/°C
+270
+155
+270
450
325
ps
ps
ps
ps
ps
681
646
865
992
ps
ps
1.02
1.07
1.39
1.44
1
1.71
1.76
ns
ns
ps/°C
tSKC
tSKC_AB
tSKC_AB
−140
+145
+300
650
500
ps
ps
ps
tSKP_V
0.74
0.92
1.14
ns
tSKP_C
0.88
1.14
1.43
ns
tSKV_C
158
353
506
ps
0.05
0.57
0.36
0.95
0.5
0.8
0.68
1.32
ns
ns
LSB
LSB
0.20
7.0
0.57
8.0
0.3
0.6
0.95
9.2
ns
ns
LSB
LSB
Test Conditions/Comments
Delay off on OUT5 and OUT6
Delay off on OUT5 and OUT6
tSKV
tSKV
tSKV
tSKV_AB
tSKV_AB
−85
−175
−175
tRC
tFC
tCMOS
B outputs are inverted, termination = open
20% to 80%; CLOAD = 3 pF
80% to 20%; CLOAD = 3 pF
Delay off on OUT5 and OUT6
Delay off on OUT5 and OUT6
0.35
−0.14
ps/°C
ps/°C
0.51
0.67
ps/°C
ps/°C
Everything the same; different logic type
LVPECL to LVDS on same part
Everything the same; different logic type
LVPECL to CMOS on same part
Everything the same; different logic type
LVDS to CMOS on same part
OUT5 (OUT6); LVDS and CMOS
Register 0x35, Register 0x39[5:1] = 11111b
Register 0x36, Register 0x3A[5:1] = 00000b
Register 0x36, Register 0x3A[5:1] = 11000b
Register 0x35, Register 0x39[5:1] = 00000b
Register 0x36, Register 0x3A[5:1] = 00000b
Register 0x36, Register 0x3A[5:1] = 11000b
These measurements are for CLK1. For CLK2, add approximately 25 ps.
This is the difference between any two similar delay paths within a single device operating at the same voltage and temperature.
This is the difference between any two similar delay paths across multiple devices operating at the same voltage and temperature.
4
The maximum delay that can be used is a little less than one half the period of the clock. A longer delay disables the output.
5
Incremental delay; does not include propagation delay.
6
All delays between zero scale and full scale can be estimated by linear interpolation.
1
2
3
Rev. B | Page 7 of 56
AD9510
Data Sheet
CLOCK OUTPUT PHASE NOISE
Table 5.
Parameter
CLK1-TO-LVPECL ADDITIVE PHASE NOISE
CLK1 = 622.08 MHz, OUT = 622.08 MHz
Divide Ratio = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
CLK1 = 622.08 MHz, OUT = 155.52 MHz
Divide Ratio = 4
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
CLK1 = 622.08 MHz, OUT = 38.88 MHz
Divide Ratio = 16
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
CLK1 = 491.52 MHz, OUT = 61.44 MHz
Divide Ratio = 8
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
> 1 MHz Offset
CLK1 = 491.52 MHz, OUT = 245.76 MHz
Divide Ratio = 2
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
CLK1 = 245.76 MHz, OUT = 61.44 MHz
Divide Ratio = 4
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
Min
Typ
Max
Unit
−125
−132
−140
−148
−153
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−128
−140
−148
−155
−161
−161
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−135
−145
−158
−165
−165
−166
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−131
−142
−153
−160
−165
−165
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−125
−132
−140
−151
−157
−158
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−138
−144
−154
−163
−164
−165
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. B | Page 8 of 56
Test Conditions/Comments
Distribution Section only, does not include
PLL or external VCO/VCXO
Input slew rate > 1 V/ns
Data Sheet
Parameter
CLK1-TO-LVDS ADDITIVE PHASE NOISE
CLK1 = 622.08 MHz, OUT= 622.08 MHz
Divide Ratio = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 622.08 MHz, OUT = 155.52 MHz
Divide Ratio = 4
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 491.52 MHz, OUT = 245.76 MHz
Divide Ratio = 2
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 491.52 MHz, OUT = 122.88 MHz
Divide Ratio = 4
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 245.76 MHz, OUT = 245.76 MHz
Divide Ratio = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
AD9510
Min
Typ
Max
Unit
−100
−110
−118
−129
−135
−140
−148
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−112
−122
−132
−142
−148
−152
−155
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−108
−118
−128
−138
−145
−148
−154
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−118
−129
−136
−147
−153
−156
−158
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−108
−118
−128
−138
−145
−148
−155
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. B | Page 9 of 56
Test Conditions/Comments
Distribution Section only; does not include
PLL or external VCO/VCXO
AD9510
Parameter
CLK1 = 245.76 MHz, OUT = 122.88 MHz
Divide Ratio = 2
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1-TO-CMOS ADDITIVE PHASE NOISE
CLK1 = 245.76 MHz, OUT = 245.76 MHz
Divide Ratio = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 245.76 MHz, OUT = 61.44 MHz
Divide Ratio = 4
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 78.6432 MHz, OUT = 78.6432 MHz
Divide Ratio = 1
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
At 1 MHz Offset
>10 MHz Offset
CLK1 = 78.6432 MHz, OUT = 39.3216 MHz
Divide Ratio = 2
At 10 Hz Offset
At 100 Hz Offset
At 1 kHz Offset
At 10 kHz Offset
At 100 kHz Offset
>1 MHz Offset
Data Sheet
Min
Typ
Max
−118
−127
−137
−147
−154
−156
−158
Unit
Test Conditions/Comments
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Distribution Section only, does not include
PLL or external VCO/VCXO
−110
−121
−130
−140
−145
−149
−156
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−122
−132
−143
−152
−158
−160
−162
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−122
−132
−140
−150
−155
−158
−160
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
−128
−136
−146
−155
−161
−162
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Rev. B | Page 10 of 56
Data Sheet
AD9510
CLOCK OUTPUT ADDITIVE TIME JITTER
Table 6.
Parameter
LVPECL OUTPUT ADDITIVE TIME JITTER
CLK1 = 622.08 MHz
Any LVPECL (OUT0 to OUT3) = 622.08 MHz
Divide Ratio = 1
CLK1 = 622.08 MHz
Any LVPECL (OUT0 to OUT3) = 155.52 MHz
Divide Ratio = 4
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT3) = 100 MHz
Divide Ratio = 4
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT3) = 100 MHz
Divide Ratio = 4
All Other LVPECL = 100 MHz
All LVDS (OUT4 to OUT7) = 100 MHz
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT3) = 100 MHz
Divide Ratio = 4
All Other LVPECL = 50 MHz
All LVDS (OUT4 to OUT7) = 50 MHz
CLK1 = 400 MHz
Any LVPECL (OUT0 to OUT3) = 100 MHz
Divide Ratio = 4
All Other LVPECL = 50 MHz
All CMOS (OUT4 to OUT7) = 50 MHz (B Outputs Off )
CLK1 = 400 MHz
Min
Typ
Max
40
fs rms
Test Conditions/Comments
Distribution Section only, does not include
PLL or external VCO/VCXO
Bandwidth = 12 kHz − 20 MHz (OC-12)
55
fs rms
Bandwidth = 12 kHz − 20 MHz (OC-3)
215
fs rms
Calculated from signal-to-noise ratio (SNR) of
ADC method, fC = 100 MHz with AIN = 170 MHz
215
fs rms
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
222
225
225
Unit
fs rms
fs rms
fs rms
Any LVPECL (OUT0 to OUT3) = 100 MHz
Divide Ratio = 4
All Other LVPECL = 50 MHz
All CMOS (OUT4 to OUT7) = 50 MHz (B Outputs On)
LVDS OUTPUT ADDITIVE TIME JITTER
CLK1 = 400 MHz
264
fs rms
LVDS (OUT4, OUT7) = 100 MHz
Divide Ratio = 4
CLK1 = 400 MHz
319
fs rms
LVDS (OUT5, OUT6) = 100 MHz
Divide Ratio = 4
Rev. B | Page 11 of 56
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method;
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Distribution Section only, does not include
PLL or external VCO/VCXO
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
AD9510
Parameter
CLK1 = 400 MHz
LVDS (OUT4, OUT7) = 100 MHz
Divide Ratio = 4
All Other LVDS = 50 MHz
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT5, OUT6) = 100 MHz
Divide Ratio = 4
All Other LVDS = 50 MHz
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT4, OUT7) = 100 MHz
Divide Ratio = 4
All Other CMOS = 50 MHz (B Outputs Off )
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT5, OUT6) = 100 MHz
Divide Ratio = 4
All Other CMOS = 50 MHz (B Outputs Off )
All LVPECL = 50 MHz
CLK1 = 400 MHz
LVDS (OUT4, OUT7) = 100 MHz
Divide Ratio = 4
All Other CMOS = 50 MHz (B Outputs On)
All LVPECL = 50 MHz
CLK1 = 400 MHz
Data Sheet
Min
Typ
395
Max
395
367
367
548
548
Unit
fs rms
fs rms
fs rms
fs rms
fs rms
fs rms
LVDS (OUT5, OUT6) = 100 MHz
Divide Ratio = 4
All Other CMOS = 50 MHz (B Outputs On)
All LVPECL = 50 MHz
CMOS OUTPUT ADDITIVE TIME JITTER
CLK1 = 400 MHz
275
fs rms
Any CMOS (OUT4 to OUT7) = 100 MHz (B Output On)
Divide Ratio = 4
CLK1 = 400 MHz
400
fs rms
Any CMOS (OUT4 to OUT7) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
All Other LVDS = 50 MHz
CLK1 = 400 MHz
374
Any CMOS (OUT4 to OUT7) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
All Other CMOS = 50 MHz (B Output Off )
fs rms
Test Conditions/Comments
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Distribution Section only, does not include
PLL or external VCO/VCXO
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Rev. B | Page 12 of 56
Data Sheet
AD9510
Parameter
CLK1 = 400 MHz
Min
Typ
555
Any CMOS (OUT4 to OUT7) = 100 MHz (B Output On)
Divide Ratio = 4
All LVPECL = 50 MHz
All Other CMOS = 50 MHz (B Output On)
DELAY BLOCK ADDITIVE TIME JITTER 1
100 MHz Output
Delay FS = 1 ns (1600 μA, 1C) Fine Adjust 00000
Delay FS = 1 ns (1600 μA, 1C) Fine Adjust 11000
Delay FS = 2 ns (800 μA, 1C) Fine Adjust 00000
Delay FS = 2 ns (800 μA, 1C) Fine Adjust 11000
Delay FS = 3 ns (800 μA, 4C) Fine Adjust 00000
Delay FS = 3 ns (800 μA, 4C) Fine Adjust 11000
Delay FS = 5 ns (400 μA, 4C) Fine Adjust 00000
Delay FS = 5 ns (400 μA, 4C) Fine Adjust 11000
Delay FS = 6 ns (200 μA, 1C) Fine Adjust 00000
Delay FS = 6 ns (200 μA, 1C) Fine Adjust 11000
Delay FS = 9 ns (200 μA, 4C) Fine Adjust 00000
Delay FS = 9 ns (200 μA, 4C) Fine Adjust 00111
1
Max
Unit
fs rms
Test Conditions/Comments
Calculated from SNR of ADC method,
fC = 100 MHz with AIN = 170 MHz
Interferer(s)
Interferer(s)
Incremental additive jitter1
0.61
0.73
0.71
1.2
0.86
1.8
1.2
2.1
1.3
2.7
2.0
2.8
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
ps
This value is incremental. That is, it is in addition to the jitter of the LVDS or CMOS output without the delay. To estimate the total jitter, add the LVDS or CMOS output
jitter to this value using the root sum of the squares (RSS) method.
PLL AND DISTRIBUTION PHASE NOISE AND SPURIOUS
Table 7.
Parameter
PHASE NOISE AND SPURIOUS
VCXO = 245.76 MHz, fPFD = 1.2288 MHz,
R = 25, N = 200
245.76 MHz Output
Phase Noise at 100 kHz Offset
Spurious
61.44 MHz Output
Phase Noise at 100 kHz Offset
Spurious
Min
Typ
Max
Unit
Test Conditions/Comments
Depends on VCO/VCXO selection; measured at LVPECL
clock outputs, ABP = 6 ns; ICP = 5 mA; Ref = 30.72 MHz
VCXO = Toyocom TCO-2112 245.76
<−145
<−97
dBc/Hz
dBc
<−155
<−97
dBc/Hz
dBc
Divide by 1
Dominated by VCXO phase noise
First and second harmonics of fPFD; below measurement floor
Divide by 4
Dominated by VCXO phase noise
First and second harmonics of fPFD; below measurement floor
SERIAL CONTROL PORT
Table 8.
Parameter
CSB, SCLK (INPUTS)
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
Min
Typ
Max
2.0
0.8
110
1
2
Rev. B | Page 13 of 56
Unit
V
V
µA
µA
pF
Test Conditions/Comments
Inputs have 30 kΩ internal pull-down
resistors
AD9510
Data Sheet
Parameter
SDIO (WHEN INPUT)
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO, SDO (OUTPUTS)
Output Logic 1 Voltage
Output Logic 0 Voltage
TIMING
Clock Rate (SCLK, 1/tSCLK)
Pulse Width High, tPWH
Pulse Width Low, tPWL
SDIO to SCLK Setup, tDS
SCLK to SDIO Hold, tDH
SCLK to Valid SDIO and SDO, tDV
CSB to SCLK Setup and Hold, tS, tH
CSB Minimum Pulse Width High, tPWH
Min
Typ
Max
2.0
0.8
10
10
2
2.7
0.4
25
16
16
2
1
6
2
3
Unit
Test Conditions/Comments
V
V
nA
nA
pF
V
V
MHz
ns
ns
ns
ns
ns
ns
ns
FUNCTION PIN
Table 9.
Parameter
INPUT CHARACTERISTICS
Min
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Capacitance
RESET TIMING
Pulse Width Low
SYNC TIMING
Pulse Width Low
2.0
Typ
Max
0.8
110
1
2
Unit
Test Conditions/Comments
FUNCTION pin has 30 kΩ internal pull-down resistor;
normally, hold this pin high; do not leave unconnected
V
V
µA
µA
pF
50
ns
1.5
High speed clock cycles
High speed clock is CLK1 or CLK2, whichever is being used
for distribution
STATUS PIN
Table 10.
Parameter
OUTPUT CHARACTERISTICS
Min
Output Voltage High (VOH)
Output Voltage Low (VOL)
MAXIMUM TOGGLE RATE
2.7
ANALOG LOCK DETECT
Capacitance
Typ
Max
Unit
0.4
100
V
V
MHz
3
pF
Test Conditions/Comments
When selected as a digital output (CMOS), there are other modes in
which the STATUS pin is not CMOS digital output; see Figure 37
Applies when PLL mux is set to any divider or counter output, or PFD up/
down pulse; also applies in analog lock detect mode; usually debug mode
only; beware that spurs can couple to output when this pin is toggling
On-chip capacitance, used to calculate RC time constant for analog lock
detect readback; use a pull-up resistor
Rev. B | Page 14 of 56
Data Sheet
AD9510
POWER
Table 11.
Parameter
POWER-UP DEFAULT MODE POWER DISSIPATION
Min
Typ
550
Max
600
Unit
mW
Power Dissipation
1.1
W
Power Dissipation
1.3
W
Power Dissipation
1.5
W
Full Sleep Power-Down
35
60
mW
Power-Down (PDB)
60
80
mW
POWER DELTA
CLK1, CLK2 Power-Down
Divider, DIV 2 − 32 to Bypass
LVPECL Output Power-Down (PD2, PD3)
10
23
50
15
27
65
25
33
75
mW
mW
mW
LVDS Output Power-Down
CMOS Output Power-Down (Static)
CMOS Output Power-Down (Dynamic)
80
56
115
92
70
150
110
85
190
mW
mW
mW
CMOS Output Power-Down (Dynamic)
125
165
210
mW
Delay Block Bypass
20
24
60
mW
PLL Section Power-Down
5
15
40
mW
Rev. B | Page 15 of 56
Test Conditions/Comments
Power-up default state, does not include power
dissipated in output load resistors; no clock
All outputs on; four LVPECL outputs at 800 MHz, 4 LVDS
out at 800 MHz; does not include power dissipated in
external resistors
All outputs on; four LVPECL outputs at 800 MHz, 4 CMOS
out at 62 MHz (5 pF load); does not include power
dissipated in external resistors
All outputs on; four LVPECL outputs at 800 MHz, 4 CMOS
out at 125 MHz (5 pF load); does not include power
dissipated in external resistors
Maximum sleep is entered by setting Register 0x0A[1:0] =
01b and Register 0x58[4] = 1b; this powers off the PLL BG
and the distribution BG references; does not include
power dissipated in terminations
Set the FUNCTION pin for PDB operation by setting
Register 0x58[6:5] = 11b; pull PDB low; does not include
power dissipated in terminations
For each divider
For each output; does not include dissipation in
termination (PD2 only)
For each output
For each output; static (no clock)
For each CMOS output, single-ended; clocking at
62 MHz with 5 pF load
For each CMOS output, single-ended; clocking at
125 MHz with 5 pF load
Versus delay block operation at 1 ns fs with maximum
delay, output clocking at 25 MHz
AD9510
Data Sheet
TIMING DIAGRAMS
DIFFERENTIAL
tCLK1
CLK1
80%
LVDS
tRL
tFL
05046-065
20%
tPECL
05046-002
tLVDS
tCMOS
Figure 2. CLK1/CLK1B to Clock Output Timing, DIV = 1 Mode
Figure 4. LVDS Timing, Differential
DIFFERENTIAL
SINGLE-ENDED
80%
80%
LVPECL
CMOS
3pF LOAD
tRP
tFP
tRC
Figure 3. LVPECL Timing, Differential
tFC
Figure 5. CMOS Timing, Single-Ended, 3 pF Load
Rev. B | Page 16 of 56
05046-066
20%
05046-064
20%
Data Sheet
AD9510
ABSOLUTE MAXIMUM RATINGS
THERMAL CHARACTERISTICS
Table 12.
Parameter
VS to GND
VCP to GND
VCP to VS
REFIN, REFINB to GND
RSET to GND
CPRSET to GND
CLK1, CLK1B, CLK2, CLK2B to GND
CLK1 to CLK1B
CLK2 to CLK2B
SCLK, SDIO, SDO, CSB to GND
OUT0, OUT1, OUT2, OUT3 to GND
OUT4, OUT5, OUT6, OUT7 to GND
FUNCTION to GND
STATUS to GND
Junction Temperature1
Storage Temperature
Lead Temperature (10 sec)
1
Value
−0.3 V to +3.6 V
−0.3 V to +5.8 V
−0.3 V to +5.8 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−1.2 V to +1.2 V
−1.2 V to +1.2 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
−0.3 V to VS + 0.3 V
150°C
−65°C to +150°C
300°C
Thermal impedance measurements were taken on a 4-layer
board in still air in accordance with EIA/JESD51-7.
Table 13. Thermal Resistance
Package
64-Lead LFCSP
ESD CAUTION
See Thermal Characteristics for θJA.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. B | Page 17 of 56
θJA
24
Unit
°C/W
AD9510
Data Sheet
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
VS
CPRSET
GND
RSET
VS
VS
OUT0
OUT0B
VS
GND
OUT1
OUT1B
VS
VS
GND
GND
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
AD9510
TOP VIEW
(Not to Scale)
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VS
OUT4
OUT4B
VS
VS
OUT5
OUT5B
VS
VS
OUT6
OUT6B
VS
VS
OUT2
OUT2B
VS
NOTES
1. THE EXPOSED PADDLE ON THIS PACKAGE IS AN ELECTRICAL CONNECTION AS
WELL AS A THERMAL ENHANCEMENT. FOR THE DEVICE TO FUNCTION PROPERLY,
THE PADDLE MUST BE ATTACHED TO GROUND, GND.
05046-003
STATUS
SCLK
SDIO
SDO
CSB
GND
VS
OUT7B
OUT7
VS
GND
OUT3B
OUT3
VS
VS
GND
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
REFIN
REFINB
GND
VS
VCP
CP
GND
GND
VS
CLK2
CLK2B
GND
VS
CLK1
CLK1B
FUNCTION
Figure 6.
Table 14. Pin Function Descriptions
Pin No.
1
2
3, 7, 8, 12, 22,
27, 32, 49, 50,
55, 62
4, 9, 13, 23, 26,
30, 31, 33, 36,
37, 40, 41, 44,
45, 48, 51, 52,
56, 59, 60, 64
5
Mnemonic
REFIN
REFINB
GND
Description
PLL Reference Input.
Complementary PLL Reference Input.
Ground.
VS
Power Supply (3.3 V) VS.
VCP
6
10
CP
CLK2
11
14
15
16
CLK2B
CLK1
CLK1B
FUNCTION
17
18
19
20
21
24
25
STATUS
SCLK
SDIO
SDO
CSB
OUT7B
OUT7
Charge Pump Power Supply VCPS. It must be greater than or equal to VS. VCPS can be set as high as 5.5 V for
VCOs requiring extended tuning range.
Charge Pump Output.
Clock Input Used to Connect External VCO/VCXO to Feedback Divider, N. CLK2 also drives the distribution
section of the chip and can be used as a generic clock input when PLL is not used.
Complementary Clock Input Used in Conjunction with CLK2.
Clock Input that Drives Distribution Section of the Chip.
Complementary Clock Input Used in Conjunction with CLK1.
Multipurpose Input Can Be Programmed as a Reset (RESETB), Sync (SYNCB), or Power-Down (PDB) Pin. This
pin is internally pulled down by a 30 kΩ resistor. If this pin is left NC, the part is in reset by default. To avoid
this, connect this pin to VS with a 1 kΩ resistor.
Output Used to Monitor PLL Status and Sync Status.
Serial Data Clock.
Serial Data I/O.
Serial Data Output.
Serial Port Chip Select.
Complementary LVDS/Inverted CMOS Output.
LVDS/CMOS Output.
Rev. B | Page 18 of 56
Data Sheet
Pin No.
28
29
34
35
38
39
42
43
46
47
53
54
57
58
61
63
AD9510
Mnemonic
OUT3B
OUT3
OUT2B
OUT2
OUT6B
OUT6
OUT5B
OUT5
OUT4B
OUT4
OUT1B
OUT1
OUT0B
OUT0
RSET
CPRSET
EPAD
Description
Complementary LVPECL Output.
LVPECL Output.
Complementary LVPECL Output.
LVPECL Output.
Complementary LVDS/Inverted CMOS Output. OUT6 includes a delay block.
LVDS/CMOS Output. OUT6 includes a delay block.
Complementary LVDS/Inverted CMOS Output. OUT5 includes a delay block.
LVDS/CMOS Output. OUT5 includes a delay block.
Complementary LVDS/Inverted CMOS Output.
LVDS/CMOS Output.
Complementary LVPECL Output.
LVPECL Output.
Complementary LVPECL Output.
LVPECL Output.
Current Set Resistor to Ground. Nominal value = 4.12 kΩ.
Charge Pump Current Set Resistor to Ground. Nominal value = 5.1 kΩ.
Exposed Paddle. The exposed paddle on this package is an electrical connection as well as a thermal
enhancement. For the device to function properly, the paddle must be attached to ground, GND.
Rev. B | Page 19 of 56
AD9510
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
1.3
0.8
4 LVPECL + 4 LVDS (DIV ON)
0.7
4 LVPECL + 4 LVDS (DIV BYPASSED)
1.2
POWER (W)
0.5
DEFAULT–3 LVPECL + 2 LVDS (DIV ON)
0.4
4 LVDS ONLY (DIV ON)
0.3
1.1
3 LVPECL + 4 CMOS (DIV ON)
1.0
4 LVPECL ONLY (DIV ON)
0.2
05046-060
0
0
400
OUTPUT FREQUENCY (MHz)
800
05046-061
0.9
0.1
0.8
0
Figure 7. Power vs. Frequency—LVPECL, LVDS (PLL Off)
20
CLK1 (EVAL BOARD)
3GHz
40
60
80
OUTPUT FREQUENCY (MHz)
100
120
Figure 10. Power vs. Frequency—LVPECL, CMOS (PLL Off)
REFIN (EVAL BOARD)
5MHz
5GHz
05046-062
05046-043
3GHz
Figure 8. CLK1 Smith Chart (Evaluation Board)
Figure 11. REFIN Smith Chart (Evaluation Board)
CLK2 (EVAL BOARD)
3GHz
5MHz
05046-044
POWER (W)
0.6
Figure 9. CLK2 Smith Chart (Evaluation Board)
Rev. B | Page 20 of 56
AD9510
10
0
0
–10
–10
–20
–20
–30
–30
–40
–40
–50
–50
–60
–60
–70
–70
05046-058
10
–80
–90
CENTER 245.75MHz
30kHz/
–80
–90
CENTER 61.44MHz
SPAN 300kHz
30kHz/
SPAN 300kHz
Figure 15. Phase Noise, LVPECL, DIV 4, fVCXO = 245.76 MHz,
fOUT = 61.44 MHz, fPFD = 1.2288 MHz, R = 25, N = 200
Figure 12. Phase Noise, LVPECL, DIV 1, FVCXO = 245.76 MHz,
fOUT = 245.76 MHz, fPFD = 1.2288 MHz, R = 25, N = 200
–135
–20
–30
–40
–50
–60
–70
05046-063
–80
100
CENTER 1.5GHz
250kHz/
–145
–150
–155
–160
–165
–170
0.1
SPAN 2.5MHz
5.0
4.5
4.5
4.0
4.0
CURRENT FROM CP PIN (mA)
5.0
3.5
PUMP UP
3.0
2.5
2.0
1.5
05046-041
1.0
0.5
0
0
0.5
1.0
1.5
2.0
VOLTAGE ON CP PIN (V)
2.5
100
Figure 16. Phase Noise (Referred to CP Output) vs. PFD Frequency (fPFD)
Figure 13. PLL Reference Spurs: VCO 1.5 GHz, fPFD = 1 MHz
PUMP DOWN
1
10
PFD FREQUENCY (MHz)
3.5
PUMP DOWN
2.5
2.0
1.5
1.0
0.5
0
0
3.0
Figure 14. Charge Pump Output Characteristics at VCPs = 3.3 V
PUMP UP
3.0
05046-042
–90
–140
05046-057
–10
PFD NOISE REFERRED TO PFD INPUT (dBc/Hz)
0
CURRENT FROM CP PIN (mA)
05046-059
Data Sheet
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOLTAGE ON CP PIN (V)
4.0
4.5
5.0
Figure 17. Charge Pump Output Characteristics at VCPs = 5.0 V
Rev. B | Page 21 of 56
AD9510
Data Sheet
1.8
DIFFERENTIAL SWING (V p-p)
1.7
1.6
1.5
1.4
VERT 500mV/DIV
05046-056
05046-053
1.3
1.2
100
HORIZ 500ps/DIV
600
1100
1600
OUTPUT FREQUENCY (MHz)
Figure 21. LVPECL Differential Output Swing vs. Frequency
Figure 18. LVPECL Differential Output at 800 MHz
VERT 100mV/DIV
700
650
600
550
500
100
HORIZ 500ps/DIV
05046-050
05046-054
DIFFERENTIAL SWING (mV p-p)
750
300
500
700
OUTPUT FREQUENCY (MHz)
900
Figure 22. LVDS Differential Output Swing vs. Frequency
Figure 19. LVDS Differential Output at 800 MHz
3.5
2pF
3.0
OUTPUT (VPK)
2.5
10pF
2.0
1.5
1.0
20pF
VERT 500mV/DIV
0
HORIZ 1ns/DIV
Figure 20. CMOS Single-Ended Output at 250 MHz with 10 pF Load
05046-047
05046-055
0.5
0
100
200
300
400
OUTPUT FREQUENCY (MHz)
500
600
Figure 23. CMOS Single-Ended Output Swing vs. Frequency and Load
Rev. B | Page 22 of 56
–110
–120
–120
–130
–130
–140
–150
–160
–160
05046-051
–150
100
1k
100k
10k
OFFSET (Hz)
–170
10
10M
1M
100
1k
10k
100k
OFFSET (Hz)
10M
1M
Figure 27. Additive Phase Noise—LVPECL DIV1, 622.08 MHz
–80
–80
–90
–90
–100
–100
–110
–110
–120
–130
–120
–130
–140
–140
–150
–150
100
1k
10k
100k
OFFSET (Hz)
1M
–160
–170
10
10M
Figure 25. Additive Phase Noise—LVDS DIV 1, 245.76 MHz
–110
–110
–120
–120
L(f) (dBc/Hz)
–100
–130
–140
–160
05046-045
–160
10k
100k
OFFSET (Hz)
1M
1M
10M
–140
–150
1k
10k
100k
OFFSET (Hz)
–130
–150
100
1k
Figure 28. Additive Phase Noise—LVDS DIV2, 122.88 MHz
–100
–170
10
100
–170
10
10M
Figure 26. Additive Phase Noise—CMOS DIV 1, 245.76 MHz
05046-046
–170
10
05046-049
L(f) (dBc/Hz)
Figure 24. Additive Phase Noise—LVPECL DIV 1, 245.76 MHz,
Distribution Section Only
–160
L(f) (dBc/Hz)
–140
05046-052
L(f) (dBc/Hz)
–110
–170
10
L(f) (dBc/Hz)
AD9510
05046-048
L(f) (dBc/Hz)
Data Sheet
100
1k
10k
100k
OFFSET (Hz)
1M
Figure 29. Additive Phase Noise—CMOS DIV4, 61.44 MHz
Rev. B | Page 23 of 56
10M
AD9510
Data Sheet
TERMINOLOGY
Phase Jitter and Phase Noise
An ideal sine wave has a continuous and even progression of
phase with time from 0 to 360 degrees for each cycle. Actual
signals, however, display a certain amount of variation from
ideal phase progression over time. This phenomenon is called
phase jitter. Although many causes can contribute to phase
jitter, one major cause is random noise, which is characterized
statistically as being Gaussian (normal) in distribution.
This phase jitter leads to a spreading out of the energy of the
sine wave in the frequency domain, producing a continuous
power spectrum. This power spectrum is usually reported as a
series of values whose units are dBc/Hz at a given offset in frequency from the sine wave (carrier). The value is a ratio, expressed
in dB, of the power contained within a 1 Hz bandwidth with
respect to the power at the carrier frequency. For each measurement, the offset from the carrier frequency is also given.
It is meaningful to integrate the total power contained within
some interval of offset frequencies (for example, 10 kHz to
10 MHz). This is called the integrated phase noise over that
frequency offset interval and can be readily related to the time
jitter due to the phase noise within that offset frequency interval.
Phase noise has a detrimental effect on the performance of
analog-to-digital converters (ADCs), digital-to-analog
converters (DACs), and signal input (RF) mixers. It lowers the
achievable dynamic range of the converters and mixers,
although they are affected in different ways.
Time Jitter
Phase noise is a frequency domain phenomenon. In the time
domain, the same effect is exhibited as time jitter. When observing
a sine wave, the time of successive zero crossings is seen to vary.
In a square wave, the time jitter is seen as a displacement of the
edges from their ideal (regular) times of occurrence. In both
cases, the variations in timing from the ideal are the time jitter.
Since these variations are random in nature, the time jitter is
specified in units of seconds root mean square (rms) or 1 sigma
of the Gaussian distribution.
Time jitter that occurs on a sampling clock for a DAC or an
ADC decreases the SNR and dynamic range of the converter.
A sampling clock with the lowest possible jitter provides the
highest performance from a given converter.
Additive Phase Noise
Additive phase noise is the amount of phase noise attributable
to the device or subsystem being measured. The phase noise of
any external oscillators or clock sources is subtracted. This
makes it possible to predict the degree to which the device
impacts the total system phase noise when used in conjunction
with the various oscillators and clock sources, each of which
contribute their own phase noise to the total. In many cases, the
phase noise of one element dominates the system phase noise.
Additive Time Jitter
Additive time jitter is the amount of time jitter attributable to
the device or subsystem being measured. The time jitter of any
external oscillators or clock sources is subtracted. This makes it
possible to predict the degree to which the device impacts the total
system time jitter when used in conjunction with the various
oscillators and clock sources, each of which contribute their
own time jitter to the total. In many cases, the time jitter of the
external oscillators and clock sources dominates the system
time jitter.
Rev. B | Page 24 of 56
Data Sheet
AD9510
TYPICAL MODES OF OPERATION
PLL WITH EXTERNAL VCXO/VCO FOLLOWED BY
CLOCK DISTRIBUTION
CLOCK DISTRIBUTION ONLY
This is the most common operational mode for the AD9510.
An external oscillator (shown as VCO/VCXO) is phase locked
to a reference input frequency applied to REFIN. The loop filter
is usually a passive design. A VCO or a VCXO can be used. The
CLK2 input is connected internally to the feedback divider, N.
The CLK2 input provides the feedback path for the PLL. If the
VCO/VCXO frequency exceeds maximum frequency of the
output or outputs being used, an appropriate divide ratio must
be set in the corresponding divider or dividers in the Distribution
Section. Save some power by shutting off unused functions and
by powering down any unused clock channels (see the Register
Map and Description section).
It is possible to use only the distribution section whenever the
PLL section is not needed. Save power by shutting off the PLL
block, and by powering down any unused clock channels (see
the Register Map and Description section).
In distribution mode, both the CLK1 and CLK2 inputs are available
for distribution to outputs via a low jitter multiplexer (mux).
VREF
AD9510
PLL
REF
REFIN
R
PFD
N
FUNCTION
CLOCK
INPUT 1
CHARGE
PUMP
STATUS
CLK1
CLK2
CLOCK
INPUT 2
LVPECL
PLL
REF
R
LVPECL
PFD
N
FUNCTION
CHARGE
PUMP
DIVIDE
LOOP
FILTER
LVPECL
DIVIDE
STATUS
CLK1
CLK2
LVPECL
VCXO,
VCO
SERIAL
PORT
LVPECL
DIVIDE
LVDS/CMOS
DIVIDE
LVDS/CMOS
DIVIDE
LVPECL
DIVIDE
∆T
DIVIDE
∆T
LVDS/CMOS
DIVIDE
LVPECL
SERIAL
PORT
CLOCK
OUTPUTS
DIVIDE
LVPECL
DIVIDE
LVDS/CMOS
LVDS/CMOS
CLOCK
OUTPUTS
DIVIDE
DIVIDE
Figure 31. Clock Distribution Mode
LVDS/CMOS
DIVIDE
∆T
DIVIDE
∆T
LVDS/CMOS
LVDS/CMOS
DIVIDE
05046-010
REFERENCE
INPUT
AD9510
REFIN
Figure 30. PLL and Clock Distribution Mode
Rev. B | Page 25 of 56
05046-011
VREF
DIVIDE
AD9510
Data Sheet
PLL WITH EXTERNAL VCO AND BAND-PASS
FILTER FOLLOWED BY CLOCK DISTRIBUTION
An external band-pass filter (BPF) can be used to improve the
phase noise and spurious characteristics of the PLL output. This
option is most appropriate to optimize cost by choosing a less
expensive VCO combined with a moderately priced filter. Note
that the BPF is shown outside of the VCO-to-N divider path,
with the BP filter outputs routed to CLK1. Save some power by
shutting off unused functions, and by powering down any unused
clock channels (see the Register Map and Description section).
VREF
REFIN
R
CHARGE
PUMP
PFD
N
FUNCTION
LOOP
FILTER
STATUS
CLK1
CLK2
VCO
LVPECL
BPF
DIVIDE
LVPECL
DIVIDE
LVPECL
DIVIDE
LVPECL
SERIAL
PORT
DIVIDE
LVDS/CMOS
CLOCK
OUTPUTS
DIVIDE
LVDS/CMOS
DIVIDE
∆T
LVDS/CMOS
DIVIDE
∆T
LVDS/CMOS
DIVIDE
Figure 32. AD9510 with VCO and BPF Filter
Rev. B | Page 26 of 56
05046-012
REFERENCE
INPUT
PLL
REF
AD9510
Data Sheet
AD9510
VS
GND
RSET
DISTRIBUTION
REF
REFIN
R DIVIDER
REFINB
N DIVIDER
FUNCTION
AD9510
PHASE
FREQUENCY
DETECTOR
SYNCB,
RESETB,
PDB
PLL
REF
CHARGE
PUMP
PLL
SETTINGS
CLK1
1.6GHz
CP
STATUS
CLK2
CLK1B
CLK2B
PROGRAMMABLE
DIVIDERS AND
PHASE ADJUST
1.6GHz
LVPECL
OUT0
/1, /2, /3... /31, /32
OUT0B
LVPECL
OUT1
/1, /2, /3... /31, /32
OUT1B
1.2GHz
LVPECL
LVPECL
OUT2
/1, /2, /3... /31, /32
OUT2B
SCLK
SDIO
SDO
LVPECL
SERIAL
CONTROL
PORT
OUT3
/1, /2, /3... /31, /32
OUT3B
CSB
LVDS/CMOS
OUT4
/1, /2, /3... /31, /32
OUT4B
LVDS/CMOS
/1, /2, /3... /31, /32
OUT5
∆T
OUT5B
800MHz
LVDS
OUT6
250MHz
CMOS
LVDS/CMOS
/1, /2, /3... /31, /32
∆T
OUT6B
LVDS/CMOS
/1, /2, /3... /31, /32
Figure 33. Functional Block Diagram Showing Maximum Frequencies
Rev. B | Page 27 of 56
OUT7
OUT7B
05046-013
250MHz
CPRSET VCP
AD9510
Data Sheet
FUNCTIONAL DESCRIPTION
OVERALL
PLL Reference Input—REFIN
Figure 33 shows a block diagram of the AD9510. The chip
combines a programmable PLL core with a configurable clock
distribution system. A complete PLL requires the addition of a
suitable external VCO (or VCXO) and loop filter. This PLL can
lock to a reference input signal and produce an output that is
related to the input frequency by the ratio defined by the programmable R and N dividers. The PLL cleans up some jitter
from the external reference signal, depending on the loop bandwidth and the phase noise performance of the VCO (VCXO).
The REFIN/REFINB pins can be driven by either a differential
or a single-ended signal. These pins are internally self-biased so
that they can be ac-coupled via capacitors. It is possible to dccouple to these inputs. If REFIN is driven single-ended, decouple
the unused side (REFINB) via a suitable capacitor to a quiet
ground. Figure 34 shows the equivalent circuit of REFIN.
Alternatively, the clock distribution section can be driven directly
by an external clock signal, and the PLL can be powered off.
Whenever the clock distribution section is used alone, there is
no clock cleanup. The jitter of the input clock signal is passed
along directly to the distribution section and may dominate at
the clock outputs.
PLL SECTION
10kΩ
150Ω
REFINB
10kΩ
150Ω
05046-033
10kΩ
Figure 34. REFIN Equivalent Circuit
VCO/VCXO Clock Input—CLK2
The CLK2 differential input is used to connect an external
VCO or VCXO to the PLL. Only the CLK2 input port has a
connection to the PLL N divider. This input can receive up to
1.6 GHz. These inputs are internally self-biased and must be
ac-coupled via capacitors.
Alternatively, CLK2 can be used as an input to the distribution
section. This is accomplished by setting Register 0x45[0] = 0b.
The default condition is for CLK1 to feed the distribution section.
CLOCK INPUT
STAGE
The AD9510 consists of a PLL section and a distribution section.
If desired, the PLL section can be used separately from the
distribution section.
The AD9510 has a complete PLL core on-chip, requiring only
an external loop filter and VCO/VCXO. This PLL is based on
the ADF4106, a PLL noted for its superb low phase noise performance. The operation of the AD9510 PLL is nearly identical
to that of the ADF4106, offering an advantage to those with
experience with the ADF series of PLLs. Differences include the
addition of differential inputs at REFIN and CLK2, a different
control register architecture. Also, the prescaler is changed to
allow N as low as 1. The AD9510 PLL implements the digital
lock detect feature somewhat differently than the ADF4106
does, offering improved functionality at higher PFD rates. See
the Register Map Description section.
12kΩ
REFIN
VS
CLK
CLKB
2.5kΩ
2.5kΩ
5kΩ
5kΩ
05046-016
The output from the VCO (VCXO) can be applied to the clock
distribution section of the chip, where it can be divided by any
integer value from 1 to 32. The duty cycle and relative phase of
the outputs can be selected. There are four LVPECL outputs,
(OUT0, OUT1, OUT2, and OUT3) and four outputs that can be
either LVDS or CMOS level outputs (OUT4, OUT5, OUT6, and
OUT7). Two of these outputs (OUT5 and OUT6) can also make
use of a variable delay block.
VS
Figure 35. CLK1, CLK2 Equivalent Input Circuit
PLL Reference Divider—R
The REFIN/REFINB inputs are routed to reference divider, R,
which is a 14-bit counter. R can be programmed to any value
from 1 to 16383 (a value of 0 results in a divide by 1) via its
control register (Register 0x0B[5:0], Register 0x0C[7:0]). The
output of the R divider goes to one of the phase frequency
detector inputs. Do not exceed the maximum allowable frequency
into the phase frequency detector (PFD). This means that the
REFIN frequency divided by R must be less than the maximum
allowable PFD frequency. See Figure 34.
Rev. B | Page 28 of 56
Data Sheet
AD9510
VCO/VCXO Feedback Divider—N (P, A, B)
A and B Counters
The N divider is a combination of a prescaler, P (3 bits), and two
counters, A (6 bits) and B (13 bits). Although the PLL of the
AD9510 is similar to the ADF4106, the AD9510 has a redesigned
prescaler that allows lower values of N. The prescaler has both
a dual modulus (DM) and a fixed divide (FD) mode. The AD9510
prescaler modes are shown in Table 15.
The AD9510 B counter has a bypass mode (B = 1), which is not
available on the ADF4106. The B counter bypass mode is valid
only when using the prescaler in FD mode. The B counter is
bypassed by writing 1 to the B counter bypass bit (Register 0x0A[6]
= 1b). The valid range of the B counter is 3 to 8191. The default
after a reset is 0, which is invalid.
Table 15. PLL Prescaler Modes
Note that the A counter is not used when the prescaler is in
FD mode.
Mode
(FD = Fixed Divide,
DM = Dual Modulus)
FD
FD
P = 2 DM
P = 4 DM
P = 8 DM
P = 16 DM
P = 32 DM
FD
Value in
Register 0x0A[4:2]
000
001
010
011
100
101
110
111
Divide By
1
2
P/P + 1 = 2/3
P/P + 1 = 4/5
P/P + 1 = 8/9
P/P + 1 = 16/17
P/P + 1 = 32/33
3
When using the prescaler in FD mode, the A counter is not
used, and the B counter may need to be bypassed. The DM
prescaler modes set some upper limits on the frequency, which
can be applied to CLK2. See Table 16.
Table 16. Frequency Limits of Each Prescaler Mode
Mode (DM = Dual Modulus)
P = 2 DM (2/3)
P = 4 DM (4/5)
P = 8 DM (8/9)
P = 16 DM
P = 32 DM
CLK2
<600 MHz
<1000 MHz
<1600 MHz
<1600 MHz
<1600 MHz
Note also that the A/B counters have their own reset bit, which
is primarily intended for testing. The A and B counters can also
be reset using the shared reset bit of the R, A, and B counters
(Register 0x09[0]).
Determining Values for P, A, B, and R
When operating the AD9510 in a dual-modulus mode, the
input reference frequency, fREF, is related to the VCO output
frequency, fVCO.
fVCO = (fREF/R) × (PB + A) = fREF × N/R
When operating the prescaler in fixed divide mode, the A
counter is not used and the equation simplifies to
fVCO = (fREF/R) × (PB) = fREF × N/R
By using combinations of dual modulus and fixed divide modes,
the AD9510 can achieve values of N all the way down to N = 1.
Table 17 shows how a 10 MHz reference input can be locked to
any integer multiple of N. Note that the same value of N can be
derived in different ways, as illustrated by N = 12.
Table 17. P, A, B, R—Smallest Values for N
fREF
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
R
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
4
4
A
X
X
X
X
X
X
0
1
2
1
X
0
1
X
0
0
1
B
1
1
3
4
5
3
3
3
3
4
5
5
5
6
6
3
3
N
1
2
3
4
5
6
6
7
8
9
10
10
11
12
12
12
13
fVCO
10
20
30
40
50
60
60
70
80
90
100
100
110
120
120
120
130
Mode
FD
FD
FD
FD
FD
FD
DM
DM
DM
DM
FD
DM
DM
FD
DM
DM
DM
Rev. B | Page 29 of 56
Notes
P = 1, B = 1 (Bypassed)
P = 2, B = 1 (Bypassed)
P = 1, B = 3
P = 1, B = 4
P = 1, B = 5
P = 2, B = 3
P/P + 1 = 2/3, A = 0, B = 3
P/P + 1 = 2/3, A = 1, B = 3
P/P + 1 = 2/3, A = 2, B = 3
P/P + 1 = 2/3, A = 1, B = 4
P = 2, B = 5
P/P + 1 = 2/3, A = 0, B = 5
P/P + 1 = 2/3, A = 1, B = 5
P = 2, B = 6
P/P + 1 = 2/3, A = 0, B = 6
P/P + 1 = 4/5, A = 0, B = 3
P/P + 1 = 4/5, A = 1, B = 3
AD9510
Data Sheet
Phase Frequency Detector (PFD) and Charge Pump
eliminates the dead zone around the phase-locked condition
and thereby reduces the potential for certain spurs that can be
impressed on the VCO signal.
The PFD takes inputs from the R counter and the N counter
(N = BP + A) and produces an output proportional to the
phase and frequency difference between them. Figure 36 is a
simplified schematic. The PFD includes a programmable delay
element that controls the width of the antibacklash pulse. This
pulse ensures that there is no dead zone in the PFD transfer
function and minimizes phase noise and reference spurs. Two
bits in Register 0x0D[1:0] control the width of the pulse.
STATUS Pin
The output multiplexer on the AD9510 allows access to various signals and internal points on the chip at the STATUS pin. Figure 37
shows a block diagram of the STATUS pin section. The function
of the STATUS pin is controlled by Register 0x0[5:2].
PLL Digital Lock Detect
VP
The STATUS pin can display two types of PLL lock detect:
digital (DLD) and analog (ALD). Whenever digital lock detect
is desired, the STATUS pin provides a CMOS level signal, which
can be active high or active low.
CHARGE
PUMP
UP
CLR1
PROGRAMMABLE
DELAY
The digital lock detect has one of two time windows, as selected
by Register 0x0D[5]. The default (Register 0x0D[5] = 0b) requires
the signal edges on the inputs to the PFD to be coincident within
9.5 ns to set the DLD true, which then must separate by at least
15 ns to give DLD = false.
CP
U3
ANTIBACKLASH
PULSE WIDTH
HI
CLR2 DOWN
D2 Q2
U2
The other setting (Register 0x0D[5] = 1) makes these coincidence times 3.5 ns for DLD = true and 7 ns for DLD = false.
GND
05046-014
N DIVIDER
The DLD can be disabled by writing 1 to Register 0x0D[6].
Figure 36. PFD Simplified Schematic and Timing (In Lock)
If the signal at REFIN goes away while DLD is true, the DLD
does not necessarily indicate loss of lock. See the Loss of
Reference section for more information.
Antibacklash Pulse
The PLL features a programmable antibacklash pulse width that
is set by the value in Register 0x0D[1:0]. The default antibacklash pulse width is 1.3 ns (Register 0x0D[1:0] = 00b) and
normally does not need to be changed. The antibacklash pulse
OFF (LOW) (DEFAULT)
DIGITAL LOCK DETECT (ACTIVE HIGH)
N DIVIDER OUTPUT
DIGITAL LOCK DETECT (ACTIVE LOW)
R DIVIDER OUTPUT
ANALOG LOCK DETECT (N-CHANNEL OPEN DRAIN)
A COUNTER OUTPUT
PRESCALER OUTPUT (NCLK)
PFD UP PULSE
PFD DOWN PULSE
LOSS OF REFERENCE (ACTIVE HIGH)
TRISTATE
ANALOG LOCK DETECT (P-CHANNEL OPEN DRAIN)
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE HIGH)
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE LOW)
LOSS OF REFERENCE (ACTIVE LOW)
SYNC
DETECT
STATUS
PIN
GND
SYNC DETECT ENABLE
0x58[0]
PLL MUX CONTROL
0x08[5:2]
Figure 37. STATUS Pin Circuit CLK1 Clock Input
Rev. B | Page 30 of 56
VS
05046-015
R DIVIDER
D1 Q1
U1
CONTROL FOR ANALOG
LOCK DETECT MODE
HI
Data Sheet
AD9510
An analog lock detect (ALD) signal can be selected. When ALD
is selected, the signal at the STATUS pin is either an open-drain
P-channel (Register 0x08[5:2] = 1100) or an open-drain
N-channel (Register 0x08[5:2] = 0101b).
The analog lock detect signal is true (relative to the selected
mode) with brief false pulses. These false pulses shorten as the
inputs to the PFD are nearer to coincidence and longer as they
are further from coincidence.
To extract a usable analog lock detect signal, an external resistorcapacitor (RC) network is required to provide an analog filter
with the appropriate RC constant to allow for the discrimination of a lock condition by an external voltage comparator. A
1 kΩ resistor in parallel with a small capacitance usually fulfills
this requirement. However, some experimentation may be
required to obtain the desired operation.
The analog lock detect function may introduce some spurious
energy into the clock outputs. It is prudent to limit the use of
the ALD when the best possible jitter/phase noise performance
is required on the clock outputs.
Loss of Reference
The AD9510 PLL can warn of a loss of reference signal at
REFIN. The loss of reference monitor internally sets a flag
called LREF. Externally, this signal can be observed in several
ways on the STATUS pin, depending on the PLL MUX control
settings in Register 0x08[5:2]. The LREF alone can be observed
as an active high signal by setting Register 0x08[5:2] = [1010] or
as an active low signal by setting Register 0x08[5:2] = [1111].
The digital lock detect (DLD) block of the AD9510 requires a
PLL reference signal to be present in order for the digital lock
detect output to be valid. It is possible to have a digital lock
detect indication (DLD = true) that remains true even after a
loss of reference signal. For this reason, the digital lock detect
signal alone cannot be relied upon if the reference has been lost.
To combine the DLD and the LREF into a single signal at the
STATUS pin, set Register 0x08[5:2] = [1101] to obtain a signal
that is the logical OR of the loss of lock (inverse of DLD) and
the loss of reference (LREF) active high. If an active low version
of this same signal is desired, set Register 0x08[5:2] = [1110].
The reference monitor is enabled only after the DLD signal is high
for the number of PFD cycles set by the value in Register 0x07[6:5].
This delay is measured in PFD cycles. The delay ranges from 3 PFD
cycles (default) to 24 PFD cycles. When the reference goes away,
LREF goes true and the charge pump goes into tristate.
User intervention is required to take the part out of this state.
First, Register 0x07[2] = 0b must be written to disable the loss
of reference circuit, taking the charge pump out of tristate and
causing LREF to go false. A second write of Register 0x07[2] = 1
is required to reenable the loss of reference circuit.
PLL LOOP LOCKS
DLD GOES TRUE
LREF IS FALSE
WRITE 0x07[2] = 0
LREF SET FALSE
CHARGE PUMP COMES
OUT OF TRISTATE
WRITE 0x07[2] = 1
LOR ENABLED
The loss of reference circuit is clocked by the signal from the
VCO, which means that there must be a VCO signal present to
detect a loss of reference.
n PFD CYCLES WITH
DLD TRUE
(n SET BY 0x07[6:5])
CHARGE PUMP
GOES INTO TRISTATE.
LREF SET TRUE.
MISSING
REFERENCE
DETECTED
CHECK FOR PRESENCE
OF REFERENCE.
LREF STAYS FALSE IF
REFERENCE IS DETECTED.
Figure 38. Loss of Reference Sequence of Events
Rev. B | Page 31 of 56
05046-034
PLL Analog Lock Detect
AD9510
Data Sheet
FUNCTION PIN
DISTRIBUTION SECTION
The FUNCTION pin (16) has three functions that are selected
by the value in Register 0x58[6:5]. This pin is internally pulled
down by a 30 kΩ resistor. If this pin is left unconnected, the
part is in reset by default. To avoid this, connect this pin to VS
with a 1 kΩ resistor.
As previously mentioned, the AD9510 is partitioned into two
operational sections: PLL and distribution. The PLL Section is
discussed previously in this data sheet. If desired, the distribution
section can be used separately from the PLL section.
RESETB: Register 0x58[6:5] = 00b (Default)
Either CLK1 or CLK2 can be selected as the input to the distribution section. The CLK1 input can be connected to drive the
distribution section only. CLK1 is selected as the source for the
distribution section by setting Register 0x45[0] = 1. This is the
power-up default state.
In its default mode, the FUNCTION pin acts as RESETB, which
generates an asynchronous reset or hard reset when pulled low.
The resulting reset writes the default values into the serial control
port buffer registers as well as loading them into the chip control
registers. When the RESETB signal goes high again, a synchronous sync is issued (see the SYNCB: Register 0x58[6:5] = 01b
section) and the AD9510 resumes operation according to the
default values of the registers.
SYNCB: Register 0x58[6:5] = 01b
Using the FUNCTION pin causes a synchronization or
alignment of phase among the various clock outputs. The
synchronization applies only to clock outputs that
•
•
•
CLK1 AND CLK2 CLOCK INPUTS
CLK1 and CLK2 work for inputs up to 1600 MHz. A higher input
slew rate improves the jitter performance. The input level must
be between approximately 150 mV p-p to no more than 2 V p-p.
Anything greater may result in turning on the protection diodes
on the input pins, which may degrade the jitter performance.
See Figure 35 for the CLK1 and CLK2 equivalent input circuit.
These inputs are fully differential and self-biased. The signal
must be ac-coupled using capacitors. If a single-ended input
must be used, this can be accommodated by ac-coupling to one
side of the differential input only. Bypass the other side of the
input to a quiet ac ground by a capacitor.
Are not powered down
The divider is not masked (no sync = 0b)
Are not bypassed (bypass = 0b)
SYNCB is level and rising edge sensitive. When SYNCB is low,
the set of affected outputs are held in a predetermined state,
defined by the start high bit of each divider. On a rising edge,
the dividers begin after a predefined number of fast clock cycles
(fast clock is the selected clock input, CLK1 or CLK2) as
determined by the values in the phase offset bits of the divider.
The SYNCB application of the FUNCTION pin is always active,
regardless of whether the pin is also assigned to perform reset
or power-down. When the SYNCB function is selected, the
FUNCTION pin does not act as either RESETB or PDB.
PDB: Register 0x58[6:5] = 11b
The FUNCTION pin can also be programmed to work as an
asynchronous full power-down, PDB. Even in this full powerdown mode, there is still some residual VS current because
some on-chip references continue to operate. In PDB mode,
the FUNCTION pin is active low. The chip remains in a powerdown state until PDB is returned to logic high. The chip returns
to the settings programmed prior to the power-down.
See the Chip Power-Down or Sleep Mode—PDB section for more
details on what occurs during a PDB initiated power-down.
Power down the unselected clock input (CLK1 or CLK2) to
eliminate any possibility of unwanted crosstalk between the
selected clock input and the unselected clock input.
DIVIDERS
Each of the eight clock outputs of the AD9510 has its own
divider. The divider can be bypassed to obtain an output at the
same frequency as the input (1×). When a divider is bypassed,
it is powered down to save power.
All integer divide ratios from 1 to 32 can be selected. A divide
ratio of 1 is selected by bypassing the divider.
Each divider can be configured for divide ratio, phase, and duty
cycle. The phase and duty cycle values that can be selected
depend on the divide ratio that is chosen.
Setting the Divide Ratio
The divide ratio is determined by the values written via the serial
control port (SCP) to the registers that control each individual
output, OUT0 to OUT7. These are the even numbered registers
beginning at Register 0x48 and going through Register 0x56.
Each of these registers is divided into bits that control the
number of clock cycles that the divider output stays high
(HIGH_CYCLES[3:0]) and the number of clock cycles that the
divider output stays low (LOW_CYCLES[7:4]). Each value is 4
bits and has the range of 0 to 15.
The divide ratio is set by
Divide Ratio = (HIGH_CYCLES + 1) + (LOW_CYCLES + 1)
Rev. B | Page 32 of 56
Data Sheet
AD9510
Example 1:
Although the second set of settings produces the same divide
ratio, the resulting duty cycle is not the same.
Set the Divide Ratio = 2
Setting the Duty Cycle
HIGH_CYCLES = 0
Example 2:
The duty cycle and the divide ratio are related. Different
divide ratios have different duty cycle options. For example, if
Divide Ratio = 2, the only duty cycle possible is 50%. If the
Divide Ratio = 4, the duty cycle can be 25%, 50%, or 75%.
Set Divide Ratio = 8
The duty cycle is set by
LOW_CYCLES = 0
Divide Ratio = (0 + 1) + (0 + 1) = 2
Duty Cycle = (HIGH_CYCLES + 1)/((HIGH_CYCLES + 1)
+ (LOW_CYCLES + 1))
HIGH_CYCLES = 3
LOW_CYCLES = 3
Divide Ratio = (3 + 1) + (3 + 1) = 8
Note that a Divide Ratio of 8 can also be obtained by setting:
See Table 18 for the values for the available duty cycles for each
divide ratio.
HIGH_CYCLES = 2
LOW_CYCLES = 4
Divide Ratio = (2 + 1) + (4 + 1) = 8
Table 18. Duty Cycle and Divide Ratio
Address 0x48 to
Address 0x56
Divide Ratio
2
3
3
4
4
4
5
5
5
5
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
8
9
9
9
Duty Cycle (%)
50
67
33
50
75
25
60
40
80
20
50
67
33
83
17
57
43
71
29
86
14
50
63
38
75
25
88
13
56
44
67
LO[7:4]
0
0
1
1
0
2
1
2
0
3
2
1
3
0
4
2
3
1
4
0
5
3
2
4
1
5
0
6
3
4
2
HI[3:0]
0
1
0
1
2
0
2
1
3
0
2
3
1
4
0
3
2
4
1
5
0
3
4
2
5
1
6
0
4
3
5
Address 0x48 to
Address 0x56
Divide Ratio
9
9
9
9
9
10
10
10
10
10
10
10
10
10
11
11
11
11
11
11
11
11
11
11
12
12
12
12
12
12
12
Rev. B | Page 33 of 56
Duty Cycle (%)
33
78
22
89
11
50
60
40
70
30
80
20
90
10
55
45
64
36
73
27
82
18
91
9
50
58
42
67
33
75
25
LO[7:4]
5
1
6
0
7
4
3
5
2
6
1
7
0
8
4
5
3
6
2
7
1
8
0
9
5
4
6
3
7
2
8
HI[3:0]
2
6
1
7
0
4
5
3
6
2
7
1
8
0
5
4
6
3
7
2
8
1
9
0
5
6
4
7
3
8
2
AD9510
Data Sheet
Address 0x48 to
Address 0x56
Divide Ratio
12
12
12
12
13
13
13
13
13
13
13
13
13
13
13
13
14
14
14
14
14
14
14
14
14
14
14
14
14
15
15
15
15
15
15
15
15
15
15
15
15
15
15
16
16
16
16
16
16
16
Duty Cycle (%)
83
17
92
8
54
46
62
38
69
31
77
23
85
15
92
8
50
57
43
64
36
71
29
79
21
86
14
93
7
53
47
60
40
67
33
73
27
80
20
87
13
93
7
50
56
44
63
38
69
31
LO[7:4]
1
9
0
A
5
6
4
7
3
8
2
9
1
A
0
B
6
5
7
4
8
3
9
2
A
1
B
0
C
6
7
5
8
4
9
3
A
2
B
1
C
0
D
7
6
8
5
9
4
A
HI[3:0]
9
1
A
0
6
5
7
4
8
3
9
2
A
1
B
0
6
7
5
8
4
9
3
A
2
B
1
C
0
7
6
8
5
9
4
A
3
B
2
C
1
D
0
7
8
6
9
5
A
4
Address 0x48 to
Address 0x56
Divide Ratio
16
16
16
16
16
16
16
16
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
19
19
19
19
19
19
19
19
19
19
19
Rev. B | Page 34 of 56
Duty Cycle (%)
75
25
81
19
88
13
94
6
53
47
59
41
65
35
71
29
76
24
82
18
88
12
94
6
50
56
44
61
39
67
33
72
28
78
22
83
17
89
11
53
47
58
42
63
37
68
32
74
26
79
LO[7:4]
3
B
2
C
1
D
0
E
7
8
6
9
5
A
4
B
3
C
2
D
1
E
0
F
8
7
9
6
A
5
B
4
C
3
D
2
E
1
F
8
9
7
A
6
B
5
C
4
D
3
HI[3:0]
B
3
C
2
D
1
E
0
8
7
9
6
A
5
B
4
C
3
D
2
E
1
F
0
8
9
7
A
6
B
5
C
4
D
3
E
2
F
1
9
8
A
7
B
6
C
5
D
4
E
Data Sheet
AD9510
Address 0x48 to
Address 0x56
Divide Ratio
19
19
19
20
20
20
20
20
20
20
20
20
20
20
20
20
21
21
21
21
21
21
21
21
21
21
21
21
22
22
22
22
22
22
22
22
22
22
22
23
23
23
23
23
23
23
23
23
Duty Cycle (%)
21
84
16
50
55
45
60
40
65
35
70
30
75
25
80
20
52
48
57
43
62
38
67
33
71
29
76
24
50
55
45
59
41
64
36
68
32
73
27
52
48
57
43
61
39
65
35
70
LO[7:4]
E
2
F
9
8
A
7
B
6
C
5
D
4
E
3
F
9
A
8
B
7
C
6
D
5
E
4
F
A
9
B
8
C
7
D
6
E
5
F
A
B
9
C
8
D
7
E
6
HI[3:0]
3
F
2
9
A
8
B
7
C
6
D
5
E
4
F
3
A
9
B
8
C
7
D
6
E
5
F
4
A
B
9
C
8
D
7
E
6
F
5
B
A
C
9
D
8
E
7
F
Address 0x48 to
Address 0x56
Divide Ratio
23
24
24
24
24
24
24
24
24
24
25
25
25
25
25
25
25
25
26
26
26
26
26
26
26
27
27
27
27
27
27
28
28
28
28
28
29
29
29
29
30
30
30
31
31
32
Rev. B | Page 35 of 56
Duty Cycle (%)
30
50
54
46
58
42
63
38
67
33
52
48
56
44
60
40
64
36
50
54
46
58
42
62
38
52
48
56
44
59
41
50
54
46
57
43
52
48
55
45
50
53
47
52
48
50
LO[7:4]
F
B
A
C
9
D
8
E
7
F
B
C
A
D
9
E
8
F
C
B
D
A
E
9
F
C
D
B
E
A
F
D
C
E
B
F
D
E
C
F
E
D
F
E
F
F
HI[3:0]
6
B
C
A
D
9
E
8
F
7
C
B
D
A
E
9
F
8
C
D
B
E
A
F
9
D
C
E
B
F
A
D
E
C
F
B
E
D
F
C
E
F
D
F
E
F
AD9510
Data Sheet
Divider Phase Offset
Table 19. Phase Offset—Start H/L Bit
The phase of each output can be selected, depending on the
divide ratio chosen. This is selected by writing the appropriate
values to the registers which set the phase and start high/low bit
for each output. These are the odd numbered registers from
Register 0x49 to Register 0x57. Each divider has a 4-bit phase
offset [3:0] and a start high or low bit [4].
Phase Offset
(Fast Clock
Rising Edges)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Following a sync pulse, the phase offset word determines how
many fast clock (CLK1 or CLK2) cycles to wait before initiating
a clock output edge. The Start H/L bit determines if the divider
output starts low or high. By giving each divider a different
phase offset, output-to-output delays can be set in increments of
the fast clock period, tCLK.
Figure 39 shows four dividers, each set for DIV = 4, 50% duty
cycle. By incrementing the phase offset from 0 to 3, each output
is offset from the initial edge by a multiple of tCLK.
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLOCK INPUT
CLK
DIVIDER OUTPUTS
DIV = 4, DUTY = 50%
START = 0,
PHASE = 0
tCLK
START = 0,
PHASE = 1
START = 0,
PHASE = 2
START = 0,
PHASE = 3
tCLK
05046-035
2 × tCLK
3 × tCLK
Figure 39. Phase Offset—All Dividers Set for DIV = 4, Phase Set from 0 to 3
For example:
CLK1 = 491.52 MHz
tCLK1 = 1/491.52 = 2.0345 ns
For DIV = 4
Address 0x49 to Address 0x57
Phase Offset[3:0]
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Start H/L[4]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
The resolution of the phase offset is set by the fast clock period
(tCLK) at CLK1 or CLK2. As a result, every divide ratio does not
have 32 unique phase offsets available. For any divide ratio, the
number of unique phase offsets is numerically equal to the
divide ratio (see Table 19):
Phase Offset 0 = 0 ns
Phase Offset 1 = 2.0345 ns
Phase Offset 2 = 4.069 ns
Phase Offset 3 = 6.104 ns
DIV = 4
The four outputs can also be described as:
OUT1 = 0°
Unique Phase Offsets Are Phase = 0, 1, 2, 3
OUT2 = 90°
DIV= 7
OUT3 = 180°
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6
OUT4 = 270°
DIV = 18
Setting the phase offset to Phase = 4 results in the same relative
phase as the first channel, Phase = 0° or 360°.
In general, by combining the 4-bit phase offset and the Start
H/L bit, there are 32 possible phase offset states (see Table 19).
Rev. B | Page 36 of 56
Unique Phase Offsets Are Phase = 0, 1, 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15, 16, 17
Data Sheet
AD9510
Phase offsets can be related to degrees by calculating the phase
step for a particular divide ratio:
Phase Step = 360°/(Divide Ratio) = 360°/DIV
Calculating the Delay
The following values and equations are used to calculate the
delay of the delay block.
Value of Ramp Current Control Bits (Register 0x35 or
Register 0x39 [2:0]) = IRAMP_BITS
Using some of the same examples,
DIV = 4
IRAMP (µA) = 200 × (IRAMP_BITS + 1)
Phase Step = 360°/4 = 90°
No. of Caps = No. of 0s + 1 in Ramp Control Capacitor
(Register 0x35 or Register 0x39 [5:3]), that is, 101 = 1 + 1 =
2; 110 = 2; 100 = 2 + 1 = 3; 001 = 2 + 1 = 3; 111 = 0 + 1 = 1)
Unique Phase Offsets in Degrees Are Phase = 0°, 90°,
180°, 270°
DIV = 7
DELAY_RANGE (ns) = 200 × ((No. of Caps + 3)/(IRAMP)) ×
1.3286
Phase Step = 360°/7 = 51.43°
Unique Phase Offsets in Degrees Are Phase = 0°, 51.43°,
102.86°, 154.29°, 205.71°, 257.15°, 308.57°
 No.of Caps − 1 
×6
Offset (ns ) = 0.34 + (1600 − I RAMP )× 10 −4 + 

I RAMP


DELAY BLOCK
OUT5 and OUT6 (LVDS/CMOS) include an analog delay element
that can be programmed (from Register 0x34 to Register 0x3A)
to give variable time delays (Δt) in the clock signal passing
through that output.
DELAY_FULL_SCALE (ns) = DELAY_RANGE × (24/31) +
Offset
FINE_ADJ = Value of Delay Fine Adjust (Register 0x36 or
Register 0x3A[5:1]), that is, 11000 = 24
CLOCK INPUT
Delay (ns) = Offset + DELAY_RANGE × FINE_ADJ × (1/31)
OUTPUTS
Figure 40. Analog Delay (OUT5 and OUT6)
The amount of delay that can be used is determined by the
frequency of the clock being delayed. The amount of delay can
approach one-half cycle of the clock period. For example, for a
10 MHz clock, the delay can extend to the full 8 ns maximum of
which the delay element is capable. However, for a 100 MHz
clock (with 50% duty cycle), the maximum delay is less than
5 ns (or half of the period).
The AD9510 offers three different output level choices:
LVPECL, LVDS, and CMOS. OUT0 to OUT3 are LVPECL only.
OUT4 to OUT7 can be selected as either LVDS or CMOS. Each
output can be enabled or turned off as needed to save power.
The simplified equivalent circuit of the LVPECL outputs is
shown in Figure 41.
OUT5 and OUT6 allow a full-scale delay in the range 1 ns to
8 ns. The full-scale delay is selected by choosing a combination
of ramp current and the number of capacitors by writing the
appropriate values into Register 0x35 and Register 0x39. There
are 25 fine delay settings (Register 0x36 and Register 0x3A =
00000b to 11000b) for each full scale, set by Register 0x36 and
Register 0x3A.
This path adds some jitter greater than that specified for the
nondelay outputs. Therefore, use the delay function primarily
for clocking digital chips, such as FPGA, ASIC, DUC, and
DDC, rather than for data converters. The jitter is higher for
long full scales (~8 ns). This is because the delay block uses a
ramp and trip points to create the variable delay. A longer ramp
means more noise can be introduced.
3.3V
OUT
OUTB
05046-037
CMOS
FINE DELAY ADJUST
(25 STEPS)
FULL-SCALE: 1ns TO 8ns
OUTPUT
DRIVER
GND
Figure 41. LVPECL Output Simplified Equivalent Circuit
3.5mA
OUT
OUTB
3.5mA
05046-038
ΔT
LVDS
05046-036
OUT5
OUT6 ONLY
MUX
÷N
ØSELECT
Figure 42. LVDS Output Simplified Equivalent Circuit
Rev. B | Page 37 of 56
AD9510
Data Sheet
POWER-DOWN MODES
Chip Power-Down or Sleep Mode—PDB
The PDB chip power-down turns off most of the functions and
currents in the AD9510. When the PDB mode is enabled, a chip
power-down is activated by taking the FUNCTION pin to a logic
low level. The chip remains in this power-down state until PDB
is brought back to logic high. When woken up, the AD9510 returns
to the settings programmed into its registers prior to the powerdown, unless the registers are changed by new programming
while the PDB mode is active.
The PDB power-down mode shuts down the currents on the
chip, except the bias current necessary to maintain the LVPECL
outputs in a safe shutdown mode. This is needed to protect the
LVPECL output circuitry from damage that can be caused by
certain termination and load configurations when tristated.
Because this is not a complete power-down, it is also called
sleep mode.
When the AD9510 is in a PDB power-down or sleep mode, the
chip is in the following state:
•
•
•
•
•
•
The PLL is off (asynchronous power-down).
All clocks and sync circuits are off.
All dividers are off.
All LVDS/CMOS outputs are off.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds to
commands.
If the AD9510 clock outputs must be synchronized to each
other, a SYNC (see the Single-Chip Synchronization section) is
required upon exiting power-down mode.
The PLL section of the AD9510 can be selectively powered
down. There are three PLL power-down modes, set by the
values in Register 0x0A[1:0], as shown in Table 20.
Individual Clock Output Power-Down
Any of the eight clock distribution outputs can be powered down
individually by writing to the appropriate registers via the SCP.
The register map details the individual power-down settings for
each output. The LVDS/CMOS outputs can be powered down,
regardless of their output load configuration.
The LVPECL outputs have multiple power-down modes (see
Register Address 3C, Register Address 3D, Register Address 3E,
and Register Address 3F in Table 25). These give some flexibility in
dealing with various output termination conditions. When the
mode is set to [10], the LVPECL output is protected from reverse
bias to 2 VBE + 1 V. If the mode is set to [11], the LVPECL output
is not protected from reverse bias and can be damaged under
certain termination conditions. This setting also affects the
operation when the distribution block is powered down with
Register 0x58[3] = 1b (see the Distribution Power-Down section).
Individual Circuit Block Power-Down
Many of the AD9510 circuit blocks (CLK1, CLK2, REFIN, and
so on) can be powered down individually. This gives flexibility
in configuring the part for power savings whenever certain chip
functions are not needed.
RESET MODES
Power-On Reset—Start-Up Conditions when VS is
Applied
A power-on reset (POR) is issued when the VS power supply is
turned on. This initializes the chip to the power-on conditions
that are determined by the default register settings. These are
indicated in the default value column of Table 24.
Table 20. Register 0x0A: PLL Power-Down
[0]
0
1
0
1
When combined with the PLL power-down, this mode results in
the lowest possible power-down current for the AD9510.
The AD9510 has several ways to force the chip into a reset
condition.
PLL Power-Down
[1]
0
0
1
1
[00], it is possible for a low impedance load on that LVPECL
output to draw significant current during this power-down. If
the LVPECL power-down mode is set to [11], the LVPECL
output is not protected from reverse bias and can be damaged
under certain termination conditions.
Mode
Normal Operation
Asynchronous Power-Down
Normal Operation
Synchronous Power-Down
Asynchronous Reset via the FUNCTION Pin
In asynchronous power-down mode, the device powers down
as soon as the registers are updated.
In synchronous power-down mode, the PLL power-down is
gated by the charge pump to prevent unwanted frequency
jumps. The device goes into power-down on the occurrence of
the next charge pump event after the registers are updated.
Distribution Power-Down
The distribution section can be powered down by writing to
Register 0x58[3] = 1. This turns off the bias to the distribution
section. If the LVPECL power-down mode is normal operation
As mentioned in the FUNCTION Pin section, a hard reset,
RESETB: Register 0x58[6:5] = 00b (Default), restores the chip
to the default settings.
Soft Reset via the Serial Port
The serial control port allows a soft reset by writing to
Register 0x00[5] = 1b. When this bit is set, the chip executes
a soft reset. This restores the default values to the internal
registers, except for Register 0x00 itself.
This bit is not self-clearing. The bit must be written to
Register 0x00[5] = 0b in order for the operation of the part
to continue.
Rev. B | Page 38 of 56
Data Sheet
AD9510
SYNCB—Hardware SYNC
The AD9510 clocks can be synchronized to each other at any
time. The outputs of the clocks are forced into a known state
with respect to each other and then allowed to continue clocking
from that state in synchronicity. Before a synchronization is
done, the FUNCTION Pin must be set to act as the SYNCB:
Register 0x58[6:5] = 01b input (Register 0x58[6:5] = 01b).
Synchronization is done by forcing the FUNCTION pin low,
creating a SYNCB signal and then releasing it.
See the SYNCB: Register 0x58[6:5] = 01b section for a more
detailed description of what happens when the SYNCB:
Register 0x58[6:5] = 01b signal is issued.
Soft SYNC—Register 0x58[2]
A soft SYNC can be issued by means of a bit in Registers 0x58[2].
This soft SYNC works the same as the SYNCB, except that the
polarity is reversed. A 1 written to this bit forces the clock outputs
into a known state with respect to each other. When a 0 is
subsequently written to this bit, the clock outputs continue
clocking from that state in synchronicity.
Multichip synchronization is enabled by writing
Register 0x58[0] = 1 on the slave AD9510. When this bit is set,
the STATUS pin becomes the output for the SYNC signal. A low
signal indicates an in-sync condition, and a high indicates an
out-of-sync condition.
Register 0x58[1] selects the number of fast clock cycles that are
the maximum separation of the slow clock edges that are considered synchronized. When Register 0x58[1] = 0 (default), the
slow clock edges must be coincident within 1 to 1.5 high speed
clock cycles. If the coincidence of the slow clock edges is closer
than this amount, the SYNC flag stays low. If the coincidence of
the slow clock edges is greater than this amount, the SYNC flag
is set high. When Register 0x58[1] = 1b, the amount of coincidence
required is 0.5 fast clock cycles to 1 fast clock cycles.
Whenever the SYNC flag is set high, indicating an out-of-sync
condition, a SYNCB signal applied simultaneously at the
FUNCTION pins of both AD9510s brings the slow clocks into
synchronization.
AD9510
MASTER
MULTICHIP SYNCHRONIZATION
The AD9510 provides a means of synchronizing two or more
AD9510s. This is not an active synchronization; it requires user
monitoring and action. The arrangement of two AD9510s to be
synchronized is shown in Figure 43.
FUNCTION
(SYNCB)
FAST CLOCK
<1GHz
OUTN
SLOW CLOCK
<250MHz
OUTM
FSYNC
SYNCB
Synchronization of two or more AD9510s requires a fast clock
and a slow clock. The fast clock can be up to 1 GHz and can be
the clock driving the master AD9510 CLK1 input or one of the
outputs of the master. The fast clock acts as the input to the
distribution section of the slave AD9510 and is connected to its
CLK1 input. The PLL can be used on the master, but the slave
PLL is not used.
The slow clock is the clock that is synchronized across the two
chips. This clock must be no faster than one-fourth of the fast
clock, and no greater than 250 MHz. The slow clock is taken
from one of the outputs of the master AD9510 and acts as the
REFIN (or CLK2) input to the slave AD9510. One of the outputs
of the slave must provide this same frequency back to the CLK2
(or REFIN) input of the slave.
Rev. B | Page 39 of 56
CLK2
REFIN
AD9510
SLAVE
FAST CLOCK
CLK1 <1GHz
SLOW
CLOCK
<250MHz
FSYNC
OUTY
SYNC
DETECT
FUNCTION
(SYNCB)
Figure 43. Multichip Synchronization
STATUS
(SYNC)
05046-039
SINGLE-CHIP SYNCHRONIZATION
AD9510
Data Sheet
SERIAL CONTROL PORT
The AD9510 serial control port is a flexible, synchronous, serial
communications port that allows an easy interface with many
industry-standard microcontrollers and microprocessors. The
AD9510 serial control port is compatible with most synchronous
transfer formats, including both the Motorola SPI® and Intel®
SSR® protocols. The serial control port allows read/write access
to all registers that configure the AD9510. Single or multiple
byte transfers are supported, as well as MSB first or LSB first
transfer formats. The AD9510 serial control port can be
configured for a single bidirectional input/output pin (SDIO
only) or for two unidirectional input/output pins (SDIO/SDO).
SERIAL CONTROL PORT PIN DESCRIPTIONS
SCLK (serial clock) is the serial shift clock. This pin is an input.
SCLK is used to synchronize serial control port reads and
writes. Write data bits are registered on the rising edge of this
clock, and read data bits are registered on the falling edge. This
pin is internally pulled down by a 30 kΩ resistor to ground.
SDIO (serial data input/output) is a dual-purpose pin and acts
as either an input only or as both an input/output. The AD9510
defaults to two unidirectional pins for input/output, with SDIO
used as an input, and SDO as an output. Alternatively, SDIO
can be used as a bidirectional input/output pin by writing to the
SDO enable register at Register 0x00[7] = 1b.
SDO (serial data out) is used only in the unidirectional input/
output mode (Register 0x00[7] = 0, default) as a separate output
pin for reading back data. The AD9510 defaults to this input/
output mode. Bidirectional input/output mode (using SDIO as
both input and output) can be enabled by writing to the SDO
enable register at Register 0x00[7] = 1.
CSB (chip select bar) is an active low control that gates the read
and write cycles. When CSB is high, SDO and SDIO are in a
high impedance state. This pin is internally pulled down by a
30 kΩ resistor to ground. Do not leave it unconnected or tied
low. See the General Operation of Serial Control Port section
on the use of the CSB in a communication cycle.
SDIO (PIN 19)
SDO (PIN 20)
CSB (PIN 21)
AD9510
SERIAL
CONTROL
PORT
05046-017
SCLK (PIN 18)
Figure 44. Serial Control Port
GENERAL OPERATION OF SERIAL CONTROL PORT
Framing a Communication Cycle with CSB
Each communications cycle (a write or a read operation) is
gated by the CSB line. CSB must be brought low to initiate a
communication cycle. CSB must be brought high at the completion of a communication cycle (see Figure 52). If CSB is not
brought high at the end of each write or read cycle (on a byte
boundary), the last byte is not loaded into the register buffer.
CSB stall high is supported in modes where three or fewer bytes
of data (plus instruction data) are transferred (W1:W0 must be
set to 00, 01, or 10, see Table 21). In these modes, CSB can
temporarily return high on any byte boundary, allowing time
for the system controller to process the next byte. CSB can go
high on byte boundaries only and can go high during either
part (instruction or data) of the transfer. During this period, the
serial control port state machine enters a wait state until all data
is sent. If the system controller decides to abort the transfer
before all of the data is sent, the state machine must be reset by
either completing the remaining transfer or by returning the
CSB low for at least one complete SCLK cycle (but less than
eight SCLK cycles). Raising the CSB on a nonbyte boundary
terminates the serial transfer and flushes the buffer.
In the streaming mode (W1:W0 = 11b), any number of data bytes
can be transferred in a continuous stream. The register address
is automatically incremented or decremented (see the MSB/LSB
First Transfers section). CSB must be raised at the end of the
last byte to be transferred, thereby ending the stream mode.
Communication Cycle—Instruction Plus Data
There are two parts to a communication cycle with the AD9510.
The first writes a 16-bit instruction word into the AD9510,
coincident with the first 16 SCLK rising edges. The instruction
word provides the AD9510 serial control port with information
regarding the data transfer, which is the second part of the
communication cycle. The instruction word defines whether
the upcoming data transfer is a read or a write, the number of
bytes in the data transfer, and the starting register address for
the first byte of the data transfer.
Write
If the instruction word is for a write operation (I15 = 0b), the
second part is the transfer of data into the serial control port
buffer of the AD9510. The length of the transfer (1, 2, 3 bytes, or
streaming mode) is indicated by 2 bits (W1:W0) in the instruction
byte. CSB can be raised after each sequence of 8 bits to stall the
bus (except after the last byte, where it ends the cycle). When
the bus is stalled, the serial transfer resumes when CSB is lowered.
Stalling on nonbyte boundaries resets the serial control port.
Since data is written into a serial control port buffer area, not
directly into the actual control registers of the AD9510, an additional operation is needed to transfer the serial control port
buffer contents to the actual control registers of the AD9510,
thereby causing them to take effect. This update command
consists of writing to Register 0x5A[0] = 1b. This update bit is
self-clearing (it is not required to write 0 to it to clear it). Since
any number of bytes of data can be changed before issuing an
update command, the update simultaneously enables all register
changes since any previous update.
Phase offsets or divider synchronization do not become
effective until a SYNC is issued (see the Single-Chip
Synchronization section).
Rev. B | Page 40 of 56
Data Sheet
AD9510
Read
If the instruction word is for a read operation (I15 = 1b), the
next N × 8 SCLK cycles clock out the data from the address
specified in the instruction word, where N is 1 to 4 as determined
by W1:W0. The readback data is valid on the falling edge of SCLK.
The default mode of the AD9510 serial control port is unidirectional mode; therefore, the requested data appears on the SDO
pin. It is possible to set the AD9510 to bidirectional mode by
writing the SDO enable register at Register 0x00[7] = 1b. In
bidirectional mode, the readback data appears on the SDIO pin.
SDO
CSB
SERIAL
CONTROL
PORT
UPDATE
REGISTERS
0x5A[0]
AD9510
CORE
05046-018
SDIO
CONTROL REGISTERS
SCLK
REGISTER BUFFERS
A readback request reads the data that is in the serial control
port buffer area, not the active data in the actual control
registers of the AD9510.
Figure 45. Relationship Between Serial Control Port Register Buffers and
Control Registers of the AD9510
The AD9510 uses Address 0x00 to Address 0x5A. Although the
AD9510 serial control port allows both 8-bit and 16-bit instructions, the 8-bit instruction mode provides access to five address
bits (A4 to A0) only, which restricts its use to the address space
Address 0x00 to Address 0x01. The AD9510 defaults to 16-bit
instruction mode on power-up. The 8-bit instruction mode
(although defined for this serial control port) is not useful for the
AD9510; therefore, it is not discussed further in this data sheet.
THE INSTRUCTION WORD (16 BITS)
The MSB of the instruction word is R/W, which indicates whether
the instruction is a read or a write. The next two bits, W1:W0,
indicate the length of the transfer in bytes. The final 13 bits are
the address (A12:A0) at which to begin the read or write operation.
For a write, the instruction word is followed by the number of
bytes of data indicated by Bits W1:W0, which is interpreted
according to Table 21.
A12:A0: These 13 bits select the address within the register map
that is written to or read from during the data transfer portion
of the communications cycle. The AD9510 does not use all of
the 13-bit address space. Only Bits[A6:A0] are needed to cover
the range of the Address 0x5A registers used by the AD9510.
Bits[A12:A7] must always be 0b. For multibyte transfers, this
address is the starting byte address. In MSB first mode,
subsequent bytes increment the address.
MSB/LSB FIRST TRANSFERS
The AD9510 instruction word and byte data can be MSB first or
LSB first. The default for the AD9510 is MSB first. Set the LSB
first mode by writing 1b to Register 0x00[6]. This takes effect
immediately (since it only affects the operation of the serial
control port) and does not require that an update be executed.
Immediately after the LSB first bit is set, all serial control port
operations are changed to LSB first order.
When MSB first mode is active, the instruction and data bytes
must be written from MSB to LSB. Multibyte data transfers in
MSB first format start with an instruction byte that includes the
register address of the most significant data byte. Subsequent
data bytes must follow in order from high address to low
address. In MSB first mode, the serial control port internal
address generator decrements for each data byte of the
multibyte transfer cycle.
When LSB_FIRST = 1b (LSB first), the instruction and data bytes
must be written from LSB to MSB. Multibyte data transfers in
LSB first format start with an instruction byte that includes the
register address of the least significant data byte followed by multiple data bytes. The serial control port internal byte address
generator increments for each byte of the multibyte transfer cycle.
The AD9510 serial control port register address decrements
from the register address just written toward Address 0x0000
for multibyte input/output operations if the MSB first mode is
active (default). If the LSB first mode is active, the serial control
port register address increments from the address just written
toward Address 0x1FFF for multibyte input/output operations.
Unused addresses are not skipped during multibyte input/output
operations; therefore, it is important to avoid multibyte input/
output operations that would include these addresses.
Table 21. Byte Transfer Count
W1
0
0
1
1
W0
0
1
0
1
Bytes to Transfer
1
2
3
Streaming mode
Rev. B | Page 41 of 56
AD9510
Data Sheet
Table 22. Serial Control Port, 16-Bit Instruction Word, MSB First
MSB
I15
I14
I13
I12
I11
I10
I9
I8
I7
I6
I5
I4
I3
I2
I1
LSB
I0
R/W
W1
W0
A12 = 0
A11 = 0
A10 = 0
A9 = 0
A8 = 0
A7 = 0
A6
A5
A4
A3
A2
A1
A0
CSB
SCLK DON'T CARE
SDIO DON'T CARE
R/W W1 W0 A12 A11 A10 A9
A8
A7
A6 A5
A4 A3 A2
A1 A0
D7 D6 D5
16-BIT INSTRUCTION HEADER
D4 D3
D2 D1
D0
D7
REGISTER (N) DATA
D6 D5
D4 D3 D2
D1 D0
DON'T CARE
REGISTER (N – 1) DATA
05046-019
DON'T CARE
Figure 46. Serial Control Port Write—MSB First, 16-Bit Instruction, 2 Bytes Data
CSB
SCLK
DON'T CARE
SDIO
DON'T CARE
R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
SDO DON'T CARE
REGISTER (N) DATA
REGISTER (N – 1) DATA
REGISTER (N – 2) DATA
REGISTER (N – 3) DATA
DON'T
CARE
05046-020
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
16-BIT INSTRUCTION HEADER
Figure 47. Serial Control Port Read—MSB First, 16-Bit Instruction, 4 Bytes Data
tDS
tS
tHI
tDH
DON'T CARE
SDIO
DON'T CARE
DON'T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
D4
D3
D2
D1
D0
DON'T CARE
05046-021
SCLK
tH
tCLK
tLO
CSB
Figure 48. Serial Control Port Write−MSB First, 16-Bit Instruction, Timing Measurements
CSB
SCLK
DATA BIT N
05046-022
tDV
SDIO
SDO
DATA BIT N– 1
Figure 49. Timing Diagram for Serial Control Port Register Read
CSB
SCLK DON'T CARE
DON'T CARE
A0 A1 A2 A3
A4
A5 A6 A7
A8
A9 A10 A11 A12 W0 W1 R/W D0 D1 D2 D3 D4
16-BIT INSTRUCTION HEADER
D5 D6
REGISTER (N) DATA
D7
D0
D1 D2
D6
REGISTER (N + 1) DATA
Figure 50. Serial Control Port Write—LSB First, 16-Bit Instruction, 2 Bytes Data
Rev. B | Page 42 of 56
D3 D4 D5
D7
DON'T CARE
05046-023
SDIO DON'T CARE
Data Sheet
AD9510
tH
tS
CSB
tCLK
tLO
tHI
tDS
SCLK
SDIO
BI N
05046-040
tDH
BI N + 1
Figure 51. Serial Control Port Timing—Write
Table 23. Serial Control Port Timing
Parameter
tDS
tDH
tCLK
tS
tH
tHI
tLO
Description
Setup time between data and rising edge of SCLK
Hold time between data and rising edge of SCLK
Period of the clock
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK must be in a logic high state
Minimum period that SCLK must be in a logic low state
CSB TOGGLE INDICATES
CYCLE COMPLETE
tPWH
CSB
16 INSTRUCTION BITS + 8 DATA BITS
16 INSTRUCTION BITS + 8 DATA BITS
SCLK
COMMUNICATION CYCLE 1
COMMUNICATION CYCLE 2
TIMING DIAGRAM FOR TWO SUCCESSIVE CUMMUNICATION CYCLES. NOTE THAT CSB MUST
BE TOGGLED HIGH AND THEN LOW AT THE COMPLETION OF A COMMUNICATION CYCLE.
Figure 52. Use of CSB to Define Communications Cycle
Rev. B | Page 43 of 56
05046-067
SDIO
AD9510
Data Sheet
REGISTER MAP AND DESCRIPTION
SUMMARY TABLE
Table 24. AD9510 Register Map
Addr
(Hex)
00
Parameter
Serial
control port
configuration
Bit 7 (MSB)
SDO inactive
(bidirectional
mode)
Bit 6
LSB_
FIRST
Bit 5
Soft
reset
01
02
03
Bit 4
Long
instruction
Bit 3
Bit 2
Bit 1
Not used
Bit 0
(LSB)
Def.
Value
(Hex)
10
Not used
Not used
Not used
PLL
04
A counter
05
B counter
06
B counter
07
PLL 1
08
PLL 2
09
PLL 3
0A
PLL 4
0B
0C
0D
R divider
R divider
PLL 5
0E33
34
35
36
37
38
39
3A
Fine delay
adjust
Delay
Bypass 5
Delay FullScale 5
Delay Fine
Adjust 5
Delay
Bypass 6
Delay FullScale 6
Delay Fine
Adjust 6
Not used
6-Bit A counter[5:0]
Not used
00
13-Bit B counter, Bits[12:8], MSB[4:0]
00
13-Bit B counter, Bits[7:0], LSB[7:0]
00
Not used
Not used
Not used
LOR
LOR
LOCK_DEL[6:5]
enable
Not used
PLL mux select[5:2] signal on STATUS pin
CP mode[1:0]
PFD
polarity
Not used
CP current[6:4]
Not
Reset R Reset N Reset All
used
counter counter counters
Not used
Prescaler P[4:2]
Power-down[1:0]
B
Not
bypass
used
Not used
14-Bit R divider, Bits[13:8], MSB[5:0]
14-Bit R divider, Bits[13:8], MSB[7:0]
Not used
Not used
Digital
Digital
Antibacklash
lock
lock
pulse width[1:0]
det.
det.
enable window
Not used
Not used
Not used
Bypass
Ramp capacitor[5:3]
Not used
Ramp current [2:0]
5-bit fine delay[5:1] (00000b to 11000b)
Not used
Not used
Not used
Not used
Must be
0
Bypass
Ramp capacitor[5:3]
Ramp current[2:0]
5-bit fine delay[5:1] (00000b to 11000b)
3B
3C
3D
Notes
Not
used
Not used
Outputs
LVPECL OUT0
LVPECL OUT1
Not used
Not used
PLL starts
in powerdown
N divider
(A)
N divider
(B)
N divider
(B)
00
00
00
01
00
00
00
01
00
00
04
01
00
00
N divider
(P)
R divider
R divider
Fine delays
bypassed
Bypass
delay
Max. delay
full-scale
Min. delay
value
Bypass
delay
Max. delay
full-scale
Min. delay
value
04
Output level[3:2]
Output level[3:2]
Rev. B | Page 44 of 56
Power-down[1:0]
Power-down[1:0]
0A
08
Off
On
Data Sheet
Addr
(Hex)
3E
3F
40
Parameter
LVPECL OUT2
LVPECL OUT3
LVDS_CMOS
OUT4
AD9510
Bit 7 (MSB)
Bit 6
Bit 5
Not used
Not used
Not used
41
LVDS_CMOS
OUT5
Not used
42
LVDS_CMOS
OUT6
Not used
43
LVDS_CMOS
OUT7
Not used
44
45
CLK1 and
CLK2
Clocks select,
power-down
(PD) options
Not used
CLKs in
PD
55
56
57
58
59
5A
CMOS
inverted
driver on
CMOS
inverted
driver on
CMOS
inverted
driver on
CMOS
inverted
driver on
Not used
REFIN PD
Def.
Value
(Hex)
08
08
02
Notes
On
On
LVDS, on
Logic
select
Output level[2:1]
Output
power
02
LVDS, on
Logic
select
Output level[2:1]
Output
power
03
LVDS, off
Logic
select
Output level[2:1]
Output
power
03
LVDS, off
01
Input
receivers
All clocks
on, select
CLK1
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
High cycles[3:0]
00
00
00
00
11
00
33
00
00
00
11
00
00
Divide by 2
Phase = 0
Divide by 2
Phase = 0
Divide by 4
Phase = 0
Divide by 8
Phase = 0
Divide by 2
Phase = 0
Divide by 4
Phase = 0
Divide by 2
Phase offset[3:0]
High cycles[3:0]
Phase offset[3:0]
00
00
00
Phase = 0
Divide by 2
Phase = 0
Sync
enable
00
FUNCTION
pin =
RESETB
Update
registers
00
Selfclearing bit
CLK to
PLL
PD
CLK2
PD
CLK1
PD
Select
CLK IN
Not used
46,
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
Bit 4
Bit 0
Bit 3
Bit 2
Bit 1
(LSB)
Output level[3:2]
Power-down[1:0]
Output level[3:2]
Power-down[1:0]
Output level[2:1]
Logic
Output
select
power
Dividers
Divider 0
Divider 0
Divider 1
Divider 1
Divider 2
Divider 2
Divider 3
Divider 3
Divider 4
Divider 4
Divider 5
Divider 5
Divider 6
Divider 6
Divider 7
Divider 7
Function
FUNCTION
Pin and sync
Update
registers
END
Bypass
Bypass
Bypass
Bypass
Bypass
Bypass
Bypass
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
No sync
Force
Low cycles[7:4]
Start H/L
Start H/L
Start H/L
Start H/L
Start H/L
Start H/L
Start H/L
Bypass
No sync
Force
Low cycles[7:4]
No sync
Force
Not used
Set FUNCTION Pin
PD sync
Start H/L
PD all
ref.
Not used
Not used
Rev. B | Page 45 of 56
Sync
reg.
Sync
select
AD9510
Data Sheet
REGISTER MAP DESCRIPTION
Table 25 lists the AD9510 control registers by hexadecimal address. A specific bit or range of bits within a register is indicated by square
brackets. For example, [3] refers to Bit 3, while [5:2] refers to the range of bits from Bit 5 through Bit 2. Table 25 describes the
functionality of the control registers on a bit-by-bit basis. For a more concise (but less descriptive) table, see Table 24.
Table 25. AD9510 Register Descriptions
Reg.
Addr.
(Hex) Bit(s) Name
Serial control port
configuration
00
[3:0]
00
[4]
Long instruction
00
[5]
Soft reset
00
[6]
LSB_FIRST
00
[7]
SDO inactive
(bidirectional
mode)
Not used
01
02
03
[7:0]
[7:0]
[7:0]
04
04
05
05
06
07
07
07
07
[5:0]
[7:6]
[4:0]
[7:5]
[7:0]
[1:0]
[2]
[4:3]
[6:5]
07
08
[7]
[1:0]
Description
Any changes to this register take effect immediately. Register 0x5A[0] update registers does not have to
be written.
Not used.
When this bit is set (1), the instruction phase is 16 bits. When this bit is clear (0), the instruction phase is
8 bits. The default, and only, mode for this part is long instruction (default = 1b).
When this bit is set (1), the chip executes a soft reset, restoring default values to the internal registers, except for
this register, Register 0x00. This bit is not self-clearing. A clear (0) must be written to it to clear it.
When this bit is set (1), the input and output data is oriented as LSB first. Additionally, register addressing
increments. If this bit is clear (0), data is oriented as MSB first and register addressing decrements
(default = 0b, MSB first)
When set (1), the SDO pin is tristate and all read data goes to the SDIO pin. When clear (0), the SDO is
active (unidirectional mode) (default = 0b).
Not used.
Not used.
Not used.
PLL settings
A counter
B counter MSBs
B counter LSBs
LOR enable
LOR initial lock
detect delay
6-bit A counter[5:0].
Not used.
13-bit B counter MSB[12:8].
Not used.
13-bit B counter LSB[7:0].
Not used.
1 = enables the loss of reference (LOR) function (default = 0b).
Not used.
LOR initial lock detect delay. Once a lock detect is indicated, this is the number of phase frequency
detector (PFD) cycles that occur prior to turning on the LOR monitor.
[6]
[5]
LOR Initial Lock Detect Delay
0
0
3 PFD cycles (default)
0
1
6 PFD cycles
1
0
12 PFD cycles
1
1
24 PFD cycles
Not used.
Charge pump mode
[1]
0
0
1
1
[0]
0
1
0
1
Rev. B | Page 46 of 56
Charge Pump Mode
Tristated (default)
Pump-up
Pump-down
Normal operation
Data Sheet
Reg.
Addr.
(Hex) Bit(s) Name
08
[5:2] PLL mux control
08
[6]
08
09
09
09
09
09
[7]
[0]
[1]
[2]
[3]
[6:4]
09
0A
[7]
[1:0]
Phase frequency
detector (PFD)
polarity
Reset all counters
N-counter reset
R-counter reset
AD9510
Description
[5]
[4]
[3]
[2]
MUXOUT—Signal on STATUS Pin
0
0
0
0
Off (signal goes low) (default)
0
0
0
1
Digital lock detect (active high)
0
0
1
0
N divider output
0
0
1
1
Digital lock detect (active low)
0
1
0
0
R divider output
0
1
0
1
Analog lock detect (N channel, open-drain)
0
1
1
0
A counter output
0
1
1
1
Prescaler output (NCLK)
1
0
0
0
PFD up pulse
1
0
0
1
PFD down pulse
1
0
1
0
Loss of reference (active high)
1
0
1
1
Tristate
1
1
0
0
Analog lock detect (P channel, open-drain)
1
1
0
1
Loss of reference or loss of lock (inverse of DLD) (active high)
1
1
1
0
Loss of reference or loss of lock (inverse of DLD) (active low)
1
1
1
1
Loss of reference (active low)
MUXOUT is the PLL portion of the STATUS output MUX.
0 = negative (default), 1 = positive.
Not used.
0 = normal (default), 1 = reset R, A, and B counters.
0 = normal (default), 1 = reset A and B counters.
0 = normal (default), 1 = reset R counter.
Not used.
Charge pump (CP)
current setting
PLL power-down
[6]
[5]
[4]
ICP (mA)
0
0
0
0.60
0
0
1
1.2
0
1
0
1.8
0
1
1
2.4
1
0
0
3.0
1
0
1
3.6
1
1
0
4.2
1
1
1
4.8
Default = 000b.
These currents assume: CPRSET = 5.1 kΩ.
Actual current can be calculated by: CP_LSB = 3.06/CPRSET.
Not used.
01 = Asynchronous power-down (default).
[1]
[0]
Mode
0
0
Normal operation
0
1
Asynchronous power-down
1
0
Normal operation
1
1
Synchronous power-down
Rev. B | Page 47 of 56
AD9510
Data Sheet
Reg.
Addr.
(Hex) Bit(s) Name
0A
[4:2] Prescaler value
(P/P + 1)
0A
0A
[5]
[6]
0A
0B
[7]
[5:0]
0C
[7:0]
0D
[1:0]
0D
0D
[4:2]
[5]
0D
0D
[6]
[7]
0E33
[0]
34
38
34
38
[7:1]
B counter bypass
Description
[4]
[3]
[2]
Mode
Prescaler Mode
0
0
0
FD
Divide by 1
0
0
1
FD
Divide by 2
0
1
0
DM
2/3
0
1
1
DM
4/5
1
0
0
DM
8/9
1
0
1
DM
16/17
1
1
0
DM
32/33
1
1
1
FD
Divide by 3
DM = dual modulus, FD = fixed divide.
Not used.
Only valid when operating the prescaler in fixed divide (FD) mode. When this bit is set, the B counter is
divided by 1. This allows the prescaler setting to determine the divide for the N divider.
Not used.
R divider MSB[13:8].
14-bit reference
counter, R MSBs
R divider MSB[7:0].
14-bit reference
counter, R LSBs
Antibacklash pulse
width
[1]
[0]
Antibacklash Pulse Width (ns)
0
0
1.3 (default)
0
1
2.9
1
0
6.0
1
1
1.3
Not used
Digital lock detect
window
[5]
Digital Lock Detect Window (ns)
Digital Lock Detect Loss of Lock Threshold (ns)
0 (default)
9.5
15
1
3.5
7
If the time difference of the rising edges at the inputs to the PFD are less than the lock detect window
time, the digital lock detect flag is set. The flag remains set until the time difference is greater than the
loss of lock threshold.
Lock detect disable 0 = normal lock detect operation (default), 1 = disable lock detect.
Not used.
Unused
Not used.
Fine delay adjust
Delay control
Delay block control bit.
OUT5
Bypasses delay block and powers it down (default = 1b).
OUT6
Not used.
Rev. B | Page 48 of 56
Data Sheet
Reg.
Addr.
(Hex) Bit(s)
[2:0]
35
39
[5:3]
35
39
Name
Ramp current
OUT5
OUT6
Ramp capacitor
OUT5
OUT6
AD9510
Description
The slowest ramp (200 µA) sets the longest full scale of approximately 10 ns.
[2]
[1]
[0]
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Selects the number of capacitors in ramp generation circuit.
More capacitors → slower ramp.
[5]
0
0
0
0
1
1
1
1
[5:1]
36
3A
3C
[1:0]
3D
3E
3F
3C
3D
3E
3F
[3:2]
Delay fine adjust
OUT5
OUT6
[4]
0
0
1
1
0
0
1
1
[3]
0
1
0
1
0
1
0
1
Ramp Current (µA)
200
400
600
800
1000
1200
1400
1600
Number of Capacitors
4 (default)
3
3
2
3
2
2
1
Sets delay within full scale of the ramp; there are 25 steps.
00000 → zero delay (default).
11000 → maximum delay.
Power-down
LVPECL
OUT0
OUT1
OUT2
OUT3
Mode
On
PD1
PD2
[1]
0
0
1
[0]
0
1
0
PD3
1
1
Description
Normal operation.
Test only—do not use.
Safe power-down. Partial power-down; use if output
has load resistors.
Total power-down. Use only if output has no
load resistors.
Output level LVPECL
OUT0
Output single-ended voltage levels for LVPECL outputs.
OUT1
OUT2
OUT3
[3]
[2]
0
0
0
1
1
0
1
1
Rev. B | Page 49 of 56
Output
On
Off
Off
Off
Output Voltage (mV)
500
340
810 (default)
660
AD9510
Data Sheet
Reg.
Addr.
(Hex) Bit(s) Name
3C
[7:4]
3D
3E
3F
40
[0]
Power-down
41
LVDS/CMOS
42
OUT4
43
OUT5
OUT6
OUT7
40
[2:1] Output current
level
41
LVDS
42
OUT4
43
OUT5
OUT6
OUT7
40
41
42
43
[3]
[4]
40
41
42
43
40
41
42
43
44
45
45
45
45
[7:0]
[0]
[1]
[2]
[3]
45
45
[4]
[5]
45
46
47
[7:6]
[7:0]
[7:0]
[7:5]
Description
Not used.
Power-down bit for both output and LVDS driver. 0 = LVDS/CMOS on (default), 1 = LVDS/CMOS power-down.
[2]
[1]
Current (mA)
0
0
1.75
0
1
3.5 (default)
1
0
5.25
1
1
7
LVDS/CMOS select 0 = LVDS (default), 1 = CMOS.
OUT4
OUT5
OUT6
OUT7
Inverted CMOS
Effects output only when in CMOS mode.
driver
0 = disable inverted CMOS driver (default), 1 = enable inverted CMOS driver.
OUT4
OUT5
OUT6
OUT7
Not used.
Clock select
CLK1 power-down
CLK2 power-down
Prescaler clock
power-down
REFIN power-down
All clock inputs
power-down
Termination (Ω)
100
100
50
50
Not used.
0: CLK2 drives distribution section, 1: CLK1 drives distribution section (default).
1 = CLK1 input is powered down (default = 0b).
1 = CLK2 input is powered down (default = 0b).
1 = shut down clock signal to PLL prescaler (default = 0b).
1 = power-down REFIN (default = 0b).
1 = power-down CLK1 and CLK2 inputs and associated bias and internal clock tree (default = 0b).
Not used.
Not used.
Not used.
Rev. B | Page 50 of 56
Data Sheet
Reg.
Addr.
(Hex) Bit(s)
[3:0]
48
4A
4C
4E
50
52
54
56
[7:4]
48
4A
4C
4E
50
52
54
56
[3:0]
49
4B
4D
4F
51
53
55
57
[4]
49
4B
4D
4F
51
53
55
57
[5]
Name
Divider high
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
Divider low
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
Phase offset
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
Start
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
Force
49
4B
4D
4F
51
53
55
57
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
AD9510
Description
Number of clock cycles divider output stays high.
Number of clock cycles divider output stays low.
Phase offset (default = 0000b).
Selects start high or start low (default = 0b).
Forces individual outputs to the state specified in start (see the previous section of this table). This
function requires that Nosync (see the next section of this table) also be set (default = 0b).
Rev. B | Page 51 of 56
AD9510
Data Sheet
Reg.
Addr.
(Hex) Bit(s)
[6]
49
4B
4D
4F
51
53
55
57
[7]
49
4B
4D
4F
51
53
55
57
58
[0]
Name
Nosync
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
Bypass divider
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
SYNC detect enable
58
[1]
SYNC select
58
[2]
Soft SYNC
58
[3]
58
[4]
Dist ref
power-down
SYNC power-down 1 = power down the SYNC (default = 0b).
58
[6:5]
58
59
5A
[7]
[7:0]
[0]
5A
End
[7:1]
Description
Ignore chip-level sync signal (default = 0b).
Bypass and power down divider logic; route clock directly to output (default = 0b).
1 = enable SYNC detect (default = 0b).
1 = raise flag if slow clocks are out-of-sync by 0.5 to 1 high speed clock cycles.
0 (default) = raise flag if slow clocks are out-of-sync by 1 to 1.5 high speed clock cycles.
The Soft SYNC bit works the same as the FUNCTION pin when in SYNCB mode, except that the polarity of
this bit is reversed. That is, a high level forces selected outputs into a known state, and a high > low
transition triggers a sync (default = 0b).
1 = power down the references for the distribution section (default = 0b).
FUNCTION pin
select
Update registers
[6]
[5]
Function
0
0
RESETB (default)
0
1
SYNCB
1
0
Test only, do not use
1
1
PDB
Not used.
Not used.
Writing a 1 to this bit updates all registers and transfers all serial control port register buffer contents to
the control registers on the next rising SCLK edge. This is a self-clearing bit; a 0 does not have to be
written to clear it.
Not used.
Rev. B | Page 52 of 56
Data Sheet
AD9510
POWER SUPPLY
The AD9510 requires a 3.3 V ± 5% power supply for VS. The
tables in the Specifications section give the performance expected
from the AD9510 with the power supply voltage within this
range. The absolute maximum range of −0.3 V − +3.6 V, with
respect to GND, must never be exceeded on the VS pin.
Follow good engineering practice in the layout of power supply
traces and the ground plane of the printed circuit board (PCB).
Bypass the power supply on the PCB with adequate capacitance
(>10 µF). Bypass the AD9510 with adequate capacitors (0.1 µF)
at all power pins as close as possible to the part. The layout of the
AD9510 evaluation board (AD9510/PCBZ or
AD9510-VCO/PCBZ) is a good example.
The AD9510 is a complex part that is programmed for its desired
operating configuration by on-chip registers. These registers are
not maintained over a shutdown of external power. This means
that the registers can lose their programmed values if VS is lost
long enough for the internal voltages to collapse. Careful bypassing
protects the part from memory loss under normal conditions.
Nonetheless, it is important that the VS power supply not become
intermittent, or the AD9510 risks losing its programming.
The internal bias currents of the AD9510 are set by the RSET and
CPRSET resistors. These resistors must be as close as possible to
the values given as conditions in the Specifications section
(RSET = 4.12 kΩ and CPRSET = 5.1 kΩ). These values are standard
1% resistor values, and are readily obtainable. The bias currents
set by these resistors determine the logic levels and operating
conditions of the internal blocks of the AD9510. The performance
figures given in the Specifications section assume that these
resistor values are used.
The VCP pin is the supply pin for the charge pump (CP). The
voltage at this pin (VCP) can be from VS up to 5.5 V, as required
to match the tuning voltage range of a specific VCO/VCXO.
This voltage must never exceed the absolute maximum of 6 V.
Additionally, never allow VCP to be less than −0.3 V below VS or
GND, whichever is lower.
The exposed metal paddle on the AD9510 package is an electrical
connection, as well as a thermal enhancement. For the device
to function properly, the paddle must be properly attached to
ground (GND). The PCB acts as a heat sink for the AD9510;
therefore, this GND connection must provide a good thermal path
to a larger dissipation area, such as a ground plane on the PCB.
See the layout of the AD9510 evaluation board (AD9510/PCBZ
or AD9510-VCO/PCBZ) for a good example.
POWER MANAGEMENT
The power usage of the AD9510 can be managed to use only the
power required for the functions being used. Unused features
and circuitry can be powered down to save power. The following
circuit blocks can be powered down, or are powered down when
not selected (see the Register Map and Description section):
•
•
•
•
•
The PLL section can be powered down if not needed.
Any of the dividers are powered down when bypassed—
equivalent to divide-by-one.
The adjustable delay blocks on OUT5 and OUT6 are
powered down when not selected.
Any output can be powered down. However, LVPECL
outputs have both a safe and an off condition. When the
LVPECL output is terminated, use only the safe shutdown
to protect the LVPECL output devices. This still consumes
some power.
The entire distribution section can be powered down when
not needed.
Powering down a functional block does not cause the programming information for that block (in the registers) to be lost.
This means that blocks can be powered on and off without
otherwise having to reprogram the AD9510. However, synchronization is lost. A SYNC must be issued to resynchronize (see
the Single-Chip Synchronization section).
Rev. B | Page 53 of 56
AD9510
Data Sheet
APPLICATIONS INFORMATION
USING THE AD9510 OUTPUTS FOR ADC CLOCK
APPLICATIONS
Any high speed ADC is extremely sensitive to the quality of the
sampling clock provided by the user. An ADC can be thought of
as a sampling mixer; any noise, distortion, or timing jitter on
the clock is combined with the desired signal at the analog-todigital output. Clock integrity requirements scale with the analog
input frequency and resolution, with higher analog input frequency applications at ≥ 14-bit resolution being the most
stringent. The theoretical SNR of an ADC is limited by the
ADC resolution and the jitter on the sampling clock. Considering
an ideal ADC of infinite resolution where the step size and
quantization error can be ignored, the available SNR can be
expressed approximately by
 1 
SNR = 20 × log 

 2πft j 
where:
f is the highest analog frequency being digitized.
tj is the rms jitter on the sampling clock.
Figure 53 shows the required sampling clock jitter as a function
of the analog frequency and effective number of bits (ENOB).
1
2πftj
The AD9510 provides four clock outputs (OUT4 to OUT7),
which are selectable as either CMOS or LVDS levels. When
selected as CMOS, these outputs provide for driving devices
requiring CMOS level logic at their clock inputs.
Whenever single-ended CMOS clocking is used, follow some of
the following general guidelines.
Point-to-point nets must be designed such that a driver has one
receiver only on the net, if possible. This allows for simple termination schemes and minimizes ringing due to possible mismatched
impedances on the net. Series termination at the source is generally
required to provide transmission line matching and/or to reduce
current transients at the driver. The value of the resistor is
dependent on the board design and timing requirements (typically
10 Ω to 100 Ω is used). CMOS outputs are limited in terms of
the capacitive load or trace length that they can drive. Typically,
trace lengths less than 3 inches are recommended to preserve
signal rise/fall times and preserve signal integrity.
18
tj = 0.1ps
16
100
tj = 1ps
MICROSTRIP
12
tj = 10ps
ENOB
14
80
60.4Ω
1.0 INCH
CMOS
5pF
GND
10
60
tj = 100ps
40
8
6
tj = 1ns
4
20
1
3
10
Figure 54. Series Termination of CMOS Output
30
05046-024
SNR (dB)
10Ω
100
FULL-SCALE SINE WAVE ANALOG INPUT FREQUENCY (MHz)
Figure 53. ENOB and SNR vs. Analog Input Frequency
See Application Note AN-756, Sampled Systems and the Effects
of Clock Phase Noise and Jitter, and Application Note AN-501,
Aperture Uncertainty and ADC System Performance.
Termination at the far end of the PCB trace is a second option.
The CMOS outputs of the AD9510 do not supply enough current
to provide a full voltage swing with a low impedance resistive,
far-end termination, as shown in Figure 55. The far-end termination network must match the PCB trace impedance and provide
the desired switching point. The reduced signal swing may still
meet receiver input requirements in some applications. This can
be useful when driving long trace lengths on less critical nets.
Many high performance ADCs feature differential clock inputs
to simplify the task of providing the required low jitter clock on
a noisy PCB. (Distributing a single-ended clock on a noisy PCB
can result in coupled noise on the sample clock. Differential
distribution has inherent common-mode rejection, which can
provide superior clock performance in a noisy environment.)
Rev. B | Page 54 of 56
VPULLUP = 3.3V
10Ω
50Ω
100Ω
CMOS
OUT4, OUT5, OUT6, OUT7
SELECTED AS CMOS
100Ω
3pF
Figure 55. CMOS Output with Far-End Termination
05046-027
SNR = 20log10
CMOS CLOCK DISTRIBUTION
05046-025
tj = 50fs
120
The AD9510 features both LVPECL and LVDS outputs that
provide differential clock outputs, which enable clock solutions
that maximize converter SNR performance. Consider the input
requirements of the ADC (differential or single-ended, logic
level, termination) when selecting the best clocking/converter
solution.
Data Sheet
AD9510
Because of the limitations of single-ended CMOS clocking,
consider using differential outputs when driving high speed
signals over long traces. The AD9510 offers both LVPECL and
LVDS outputs, which are better suited for driving long traces
where the inherent noise immunity of differential signaling
provides superior performance for clocking converters.
LVPECL CLOCK DISTRIBUTION
The low voltage, positive emitter-coupled, logic (LVPECL)
outputs of the AD9510 provide the lowest jitter clock signals
available from the AD9510. The LVPECL outputs (because they
are open emitter) require a dc termination to bias the output
transistors. A simplified equivalent circuit in Figure 41 shows
the LVPECL output stage.
LVDS CLOCK DISTRIBUTION
Low voltage differential signaling (LVDS) is a second differential
output option for the AD9510. LVDS uses a current mode
output stage with several user-selectable current levels. The
normal value (default) for this current is 3.5 mA, which yields
350 mV output swing across a 100 Ω resistor. The LVDS outputs
meet or exceed all ANSI/TIA/EIA-644 specifications.
A recommended termination circuit for the LVDS outputs is
shown in Figure 58.
3.3V
LVDS
50Ω
LVPECL
127Ω
127Ω
SINGLE-ENDED
(NOT COUPLED)
LVPECL
POWER AND GROUNDING CONSIDERATIONS AND
POWER SUPPLY REJECTION
83Ω
05046-030
83Ω
Figure 58. LVDS Output Termination
3.3V
50Ω
VT = VCC – 1.3V
Figure 56. LVPECL Far-End Termination
Many applications seek high speed and performance under less
than ideal operating conditions. In these application circuits,
the implementation and construction of the PCB is as important as
the circuit design. Proper RF techniques must be used for device
selection, placement, and routing, as well as for power supply
bypassing and grounding to ensure optimum performance.
3.3V
3.3V
0.1nF
200Ω
0.1nF
DIFFERENTIAL
(COUPLED)
100Ω
LVPECL
200Ω
05046-031
LVPECL
LVDS
See Application Note AN-586, LVDS Data Outputs for High-Speed
Analog-to-Digital Converters, for more information on LVDS.
3.3V
3.3V
100Ω
100Ω
DIFFERENTIAL (COUPLED)
05046-032
In most applications, a standard LVPECL far-end termination is
recommended, as shown in Figure 56. The resistor network is
designed to match the transmission line impedance (50 Ω) and
the desired switching threshold (1.3 V).
3.3V
Figure 57. LVPECL with Parallel Transmission Line
Rev. B | Page 55 of 56
AD9510
Data Sheet
OUTLINE DIMENSIONS
9.10
9.00 SQ
8.90
0.60 MAX
0.60
MAX
64
49
48
PIN 1
INDICATOR
1
PIN 1
INDICATOR
8.85
8.75 SQ
8.65
0.50
BSC
0.50
0.40
0.30
33
32
0.30
0.23
0.18
0.25 MIN
0.20 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
*COMPLIANT TO JEDEC STANDARDS MO-220-VMMD-4
EXCEPT FOR EXPOSED PAD DIMENSION
06-13-2012-A
0.05 MAX
0.02 NOM
SEATING
PLANE
16
7.50 REF
0.80 MAX
0.65 TYP
12° MAX
4.70 SQ
4.55
17
BOTTOM VIEW
TOP VIEW
1.00
0.85
0.80
*4.85
EXPOSED
PAD
Figure 59. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
9 mm × 9 mm Body, Very Thin Quad
(CP-64-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD9510BCPZ
AD9510BCPZ-REEL7
AD9510/PCBZ
AD9510-VCO/PCBZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board Without VCO or VCXO or Loop Filter
Evaluation Board With 245.76 MHz VCXO, Loop Filter
Z = RoHS compliant part.
©2005–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05046-0-9/13(B)
Rev. B | Page 56 of 56
Package Option
CP-64-1
CP-64-1