PDF Data Sheet Rev. C

14-Bit, 160 MSPS TxDAC+
with 2× Interpolation Filter
AD9772A
FEATURES
APPLICATIONS
FUNCTIONAL BLOCK DIAGRAM
CLKCOM CLKVDD MOD0 MOD1 RESET PLLLOCK DIV0 DIV1
CLK+
AD9772A
CLOCK DISTRIBUTION
AND MODE SELECT
CLK–
1×
DATA
INPUTS
(DB13 TO
DB0)
1×/2×
EDGETRIGGERED
LATCHES
FILTER
MUX
CONTROL CONTROL
2× FIR
INTERPOLATION
FILTER
ZEROSTUFF
MUX
PLL CLOCK
MULTIPLIER
PLLVDD
2×/4×
14-BIT DAC
1.2V REFERENCE
AND CONTROL AMP
SLEEP
DCOM DVDD
ACOM AVDD
PLLCOM
LPF
IOUTA
IOUTB
REFIO
FSADJ
REFLO
02253-001
Single 3.1 V to 3.5 V supply
14-bit DAC resolution and input data width
160 MSPS input data rate
67.5 MHz reconstruction pass band @ 160 MSPS
74 dBc SFDR @ 25 MHz
2× interpolation filter with high- or low-pass response
73 dB image rejection with 0.005 dB pass-band ripple
Zero-stuffing option for enhanced direct IF performance
Internal 2×/4× clock multiplier
250 mW power dissipation; 13 mW with power-down mode
48-lead LQFP package
Figure 1.
Communication transmit channel
W-CDMA base stations, multicarrier base stations,
direct IF synthesis, wideband cable systems
Instrumentation
GENERAL DESCRIPTION
The AD9772A is a single-supply, oversampling, 14-bit digitalto-analog converter (DAC) optimized for baseband or IF
waveform reconstruction applications requiring exceptional
dynamic range. Manufactured on an advanced CMOS process,
it integrates a complete, low distortion 14-bit DAC with a 2×
digital interpolation filter and clock multiplier. The on-chip PLL
clock multiplier provides all the necessary clocks for the digital
filter and the 14-bit DAC. A flexible differential clock input
allows for a single-ended or differential clock driver for
optimum jitter performance.
For baseband applications, the 2× digital interpolation filter
provides a low-pass response, thus providing as much as a
threefold reduction in the complexity of the analog reconstruction filter. It does so by multiplying the input data rate by a
factor of 2 while suppressing the original upper in-band image
by more than 73 dB. For direct IF applications, the 2× digital
interpolation filter response can be reconfigured to select the
upper in-band image (that is, the high-pass response) while
suppressing the original baseband image. To increase the signal
level of the higher IF images and their pass-band flatness in
direct IF applications, the AD9772A also features a zero-stuffing
option in which the data following the 2× interpolation filter is
upsampled by a factor of 2 by inserting midscale data samples.
The AD9772A can reconstruct full-scale waveforms with bandwidths of up to 67.5 MHz while operating at an input data rate
of 160 MSPS. The 14-bit DAC provides differential current
outputs to support differential or single-ended applications.
A segmented current source architecture is combined with a
proprietary switching technique to reduce spurious components
and enhance dynamic performance. Matching between the two
current outputs ensures enhanced dynamic performance in a
differential output configuration. The differential current
outputs can be fed into a transformer or a differential op amp
topology to obtain a single-ended output voltage using an
appropriate resistive load.
The on-chip band gap reference and control amplifier are configured for maximum accuracy and flexibility. The AD9772A
can be driven by the on-chip reference or by a variety of
external reference voltages. The full-scale current of the
AD9772A can be adjusted over a 2 mA to 20 mA range, thus
providing additional gain-ranging capabilities.
The AD9772A is available in a 48-lead LQFP package and is
specified for operation over the industrial temperature range of
–40°C to +85°C.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
AD9772A
TABLE OF CONTENTS
Features .............................................................................................. 1
DAC Transfer Function ............................................................. 22
Applications....................................................................................... 1
Reference Operation .................................................................. 22
Functional Block Diagram .............................................................. 1
Reference Control Amplifier .................................................... 23
General Description ......................................................................... 1
Analog Outputs .......................................................................... 23
Revision History ............................................................................... 2
Digital Inputs/Outputs .............................................................. 24
Product Highlights ........................................................................... 3
Sleep Mode Operation............................................................... 25
Specifications..................................................................................... 4
Power Dissipation....................................................................... 25
DC Specifications ......................................................................... 4
Applying the AD9772A ................................................................. 26
Dynamic Specifications ............................................................... 6
Output Configurations .............................................................. 26
Digital Specifications ................................................................... 7
Differential Coupling Using a Transformer ............................... 26
Digital Filter Specifications ......................................................... 8
Differential Coupling Using an Op Amp................................ 26
Absolute Maximum Ratings............................................................ 9
Single-Ended, Unbuffered Voltage Output............................. 26
Thermal Characteristics .............................................................. 9
Single-Ended, Buffered Voltage Output.................................. 27
ESD Caution.................................................................................. 9
Power and Grounding Considerations.................................... 27
Pin Configuration and Function Descriptions........................... 10
Applications Information .............................................................. 29
Terminology .................................................................................... 12
Multicarrier ................................................................................. 29
Typical Performance Characteristics ........................................... 14
Baseband Single-Carrier Applications .................................... 30
Theory of Operation ...................................................................... 17
Direct IF....................................................................................... 30
Functional Description.............................................................. 17
AD9772A Evaluation Board ......................................................... 32
Digital Modes of Operation ...................................................... 17
Schematics................................................................................... 33
PLL Clock Multiplier Operation .............................................. 19
Evaluation Board Layout........................................................... 35
Synchronization of Clock/Data
Using Reset with PLL Disabled................................................. 21
Outline Dimensions ....................................................................... 38
Ordering Guide .......................................................................... 38
DAC Operation........................................................................... 22
REVISION HISTORY
2/08—Rev. B to Rev. C
Changes to DVDD Parameter......................................................... 4
Changes to PLL Clock Enabled Parameter ................................... 7
Changes to PLL Clock Disabled Parameter .................................. 7
Changes to Table 8.......................................................................... 10
Changes to Functional Description ............................................. 17
Change to Power Dissipation Section.......................................... 25
Changes to Power and Grounding Considerations Section ..... 27
Change to Figure 53 ....................................................................... 29
Change to Direct IF Section.......................................................... 30
Changes to Figure 61...................................................................... 34
Updated Outline Dimensions ....................................................... 38
Changes to Ordering Guide .......................................................... 38
6/03—Rev. A to Rev. B
Change to Features .......................................................................... 1
Change to DC Specifications .......................................................... 2
Change to Digital Filter Specifications ...........................................5
Ordering Guide Updated .................................................................6
Change to Pin Function Descriptions ............................................7
Change to Figure 13a and Figure 13b.......................................... 15
Change to Digital Inputs/Outputs................................................ 18
Change to Sleep Mode Operation ................................................ 19
Change to Figure 22 ....................................................................... 19
Change to Figure 23 ....................................................................... 19
Change to Power and Ground Considerations .......................... 21
Change to Figure 29 ....................................................................... 21
Update to Outline Dimensions..................................................... 30
3/02—Rev. 0 to Rev. A
Edits to Digital Specifications..........................................................4
Edits to Absolute Maximum Ratings ..............................................6
Change to TPC 11 .......................................................................... 10
Change to Figure 9 Caption .......................................................... 14
Change to Figure 13a and Figure 13b.......................................... 15
Rev. C | Page 2 of 40
AD9772A
4.
PRODUCT HIGHLIGHTS
1.
2.
3.
A flexible, low power 2× interpolation filter supporting
reconstruction bandwidths of up to 67.5 MHz can be
configured for a low- or high-pass response with 73 dB
of image rejection for traditional baseband or direct IF
applications.
A zero-stuffing option enhances direct IF applications.
A low glitch, fast settling 14-bit DAC provides exceptional
dynamic range for both baseband and direct IF waveform
reconstruction applications.
5.
6.
Rev. C | Page 3 of 40
The AD9772A digital interface, consisting of edge-triggered
latches and a flexible differential or single-ended clock input,
can support input data rates up to 160 MSPS.
An on-chip PLL clock multiplier generates all of the
internal high speed clocks required by the interpolation
filter and DAC.
The current output(s) of the AD9772A can easily be
configured for various single-ended or differential circuit
topologies.
AD9772A
SPECIFICATIONS
DC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
DC ACCURACY 1
Integral Linearity Error (INL)
Differential Nonlinearity (DNL)
Monotonicity (12-Bit)
ANALOG OUTPUT
Offset Error
Gain Error
Without Internal Reference
With Internal Reference
Full-Scale Output Current 2
Output Compliance Range
Output Resistance
Output Capacitance
REFERENCE OUTPUT
Reference Voltage
Reference Output Current 3
REFERENCE INPUT
Input Compliance Range
Reference Input Resistance (REFLO = 3 V)
Small-Signal Bandwidth
TEMPERATURE COEFFICIENTS
Unipolar Offset Drift
Gain Drift
Without Internal Reference
With Internal Reference
Reference Voltage Drift
POWER SUPPLY
AVDD
Voltage Range
Analog Supply Current (IAVDD)
Analog Supply Current in Sleep Mode (IAVDD)
DVDD
Voltage Range
Digital Supply Current (IDVDD)
CLKVDD, PLLVDD 4 (PLLVDD = 3.3 V)
Voltage Range
Clock Supply Current (ICLKVDD + IPLLVDD)
Min
14
Typ
Max
±3.5
±2.0
Guaranteed over specified temperature range
−0.025
−2
−5
±0.5
±1.5
20
−1.0
% of FSR
+2
+5
% of FSR
% of FSR
mA
V
kΩ
pF
+1.25
1.20
1
LSB
LSB
+0.025
200
3
1.14
Unit
Bits
1.26
V
μA
1.25
10
0.5
V
MΩ
MHz
0
ppm of FSR/°C
±50
±100
±50
ppm of FSR/°C
ppm of FSR/°C
ppm/°C
0.1
3.1
3.3
34
4.3
3.5
37
6
V
mA
mA
3.1
3.3
37
3.5
40
V
mA
3.1
3.3
25
3.5
30
V
mA
Rev. C | Page 4 of 40
AD9772A
Parameter
CLKVDD (PLLVDD = 0 V)
Voltage Range
Clock Supply Current (ICLKVDD)
Nominal Power Dissipation 5
Power Supply Rejection Ratio (PSRR) 6
PSRR − AVDD
PSRR − DVDD
OPERATING RANGE
Min
Typ
Max
Unit
3.1
3.3
6.0
253
3.5
272
V
mA
mW
+0.6
+0.025
+85
% of FSR/V
% of FSR/V
°C
−0.6
−0.025
−40
1
Measured at IOUTA driving a virtual ground.
Nominal full-scale current, IOUTFS, is 32× the IREF current.
3
Use an external amplifier to drive any external load.
4
Measured at fDATA = 100 MSPS and fOUT = 1 MHz with DIV1 and DIV0 = 0 V.
5
Measured with PLL enabled at fDATA = 50 MSPS and fOUT = 1 MHz.
6
Measured over a 3.0 V to 3.6 V range.
2
Rev. C | Page 5 of 40
AD9772A
DYNAMIC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 3.3 V, IOUTFS = 20 mA, differential transformer-coupled
output, 50 Ω doubly terminated, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
Maximum DAC Output Update Rate (fDAC)
Output Settling Time (tST) (to 0.025%)
Output Propagation Delay 1 (tPD)
Output Rise Time (10% to 90%) 2
Output Fall Time (10% to 90%)
Output Noise (IOUTFS = 20 mA)
AC LINEARITY—BASEBAND MODE
Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS)
fDATA = 65 MSPS; fOUT = 1.01 MHz
fDATA = 65 MSPS; fOUT = 10.01 MHz
fDATA = 65 MSPS; fOUT = 25.01 MHz
fDATA = 160 MSPS; fOUT = 5.02 MHz
fDATA = 160 MSPS; fOUT = 20.02 MHz
fDATA = 160 MSPS; fOUT = 50.02 MHz
Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = −6 dBFS)
fDATA = 65 MSPS; fOUT1 = 5.01 MHz; fOUT2 = 6.01 MHz
fDATA = 65 MSPS; fOUT1 = 15.01 MHz; fOUT2 = 17.51 MHz
fDATA = 65 MSPS; fOUT1 = 24.1 MHz; fOUT2 = 26.2 MHz
fDATA = 160 MSPS; fOUT1 = 10.02 MHz; fOUT2 = 12.02 MHz
fDATA = 160 MSPS; fOUT1 = 30.02 MHz; fOUT2 = 35.02 MHz
fDATA = 160 MSPS; fOUT1 = 48.2 MHz; fOUT2 = 52.4 MHz
Total Harmonic Distortion (THD)
fDATA = 65 MSPS; fOUT = 1.0 MHz; 0 dBFS
fDATA = 78 MSPS; fOUT = 10.01 MHz; 0 dBFS
Signal-to-Noise Ratio (SNR)
fDATA = 65 MSPS; fOUT = 16.26 MHz; 0 dBFS
fDATA = 100 MSPS; fOUT = 25.1 MHz; 0 dBFS
Adjacent Channel Power Ratio (ACPR)
WCDMA with 4.1 MHz BW, 5 MHz Channel Spacing
IF = 16 MHz, fDATA = 65.536 MSPS
IF = 32 MHz, fDATA = 131.072 MSPS
Four-Tone Intermodulation
15.6 MHz, 15.8 MHz, 16.2 MHz, and 16.4 MHz at −12 dBFS
fDATA = 65 MSPS, Missing Center
AC LINEARITY—IF MODE
Four-Tone Intermodulation at IF = 70 MHz
68.1 MHz, 69.3 MHz, 71.2 MHz, and 72.0 MHz at −20 dBFS
fDATA = 52 MSPS, fDAC = 208 MHz
1
2
Propagation delay is delay from the CLK+/CLK− input to the DAC update.
Measured single-ended into 50 Ω load.
Rev. C | Page 6 of 40
Min
Typ
400
Max
Unit
11
17
0.8
0.8
50
MSPS
ns
ns
ns
ns
pA√Hz
82
75
73
82
75
65
dBc
dBc
dBc
dBc
dBc
dBc
85
75
68
85
70
65
dBc
dBc
dBc
dBc
dBc
dBc
−80
−74
dB
dB
71
71
dB
dB
78
68
dBc
dBc
88
dBFS
77
dBFS
AD9772A
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 3.
Parameter
DIGITAL INPUTS
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current 1
Logic 0 Current
Input Capacitance
CLOCK INPUTS
Input Voltage Range
Common-Mode Voltage
Differential Voltage
PLL CLOCK ENABLED (SEE Figure 2)
Input Setup Time (tS)
TA = 25°C
TA = −40 to +85°C
Input Hold Time (tH)
TA = 25°C
TA = −40 to +85°C
Latch Pulse Width (tLPW), TA = 25°C
PLL CLOCK DISABLED (SEE Figure 3)
Input Setup Time (tS)
TA = 25°C
TA = −40 to +85°C
Input Hold Time (tH)
TA = 25°C
TA = −40 to +85°C
Latch Pulse Width (tLPW), TA = 25°C
CLK+/CLK− to PLLLOCK Delay (tOD)
TA = 25°C
TA = −40 to +85°C
PLLLOCK (VOH), TA = 25°C
PLLLOCK (VOL), TA = 25°C
Typ
2.1
3
0
−10
−10
Max
Unit
0.9
+10
+10
V
V
μA
μA
pF
5
0
0.75
0.5
3
2.25
1.5
1.5
V
V
V
1.5
2.1
ns
ns
1.3
1.6
1.5
ns
ns
ns
−0.7
−0.4
ns
ns
3.3
3.7
1.5
ns
ns
ns
1.9
1.8
3.0
2.8
3.3
0.3
ns
ns
V
V
MOD0, MOD1, DIV0, DIV1, SLEEP, RESET have typical input currents of 15 μA.
DB0 TO DB13
DB0 TO DB13
CLK+ – CLK–
IOUTA
OR
IOUTB
PLLLOCK
tLPW
tPD
tH
tS
tST
CLK+ – CLK–
0.025%
0.025%
Figure 2. Timing Diagram—PLL Clock Multiplier Enabled
tOD
tLPW
tPD
IOUTA
OR
IOUTB
tST
0.025%
0.025%
Figure 3. Timing Diagram—PLL Clock Multiplier Disabled
Rev. C | Page 7 of 40
02253-003
tS
tH
02253-002
1
Min
AD9772A
DIGITAL FILTER SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, differential transformer-coupled output,
50 Ω doubly terminated, unless otherwise noted.
Table 4.
Parameter
MAXIMUM INPUT DATA RATE (fDATA)
DIGITAL FILTER CHARACTERISTICS
Pass-Bandwidth 1 : 0.005 dB
Pass-Bandwidth: 0.01 dB
Pass-Bandwidth: 0.1 dB
Pass-Bandwidth: −3 dB
LINEAR PHASE (FIR IMPLEMENTATION)
STOP BAND REJECTION
0.606 fCLOCK to 1.394 fCLOCK
GROUP DELAY 2
IMPULSE RESPONSE DURATION
−40 dB
−60 dB
Typ
Max
Unit
MSPS
0.401
0.404
0.422
0.479
fOUT/fDATA
fOUT/fDATA
fOUT/fDATA
fOUT/fDATA
73
11
dB
Input clocks
36
42
Input clocks
Input clocks
Excludes sin(x)/x characteristic of DAC.
Defined as the number of data clock cycles between impulse input and peak of output response.
0
Table 5. Integer Filter Coefficients for Interpolation Filter
(43-Tap Half-Band FIR Filter)
–20
–40
OUTPUT (dB)
–60
–80
–100
–140
0
0. 1
0. 2
0.3 0. 4
0.5 0.6
0.7
FREQUENCY (DC TO fDATA )
0.8
0.9
1.0
02253-004
–120
Figure 4. FIR Filter Frequency Response—Baseband Mode
1.0
0.8
0.6
0.4
0.2
0
–0.2
–0.4
0
5
10
15
20
25
30
TIME (Samples)
35
40
45
Lower
Coefficient
H(1)
H(2)
H(3)
H(4)
H(5)
H(6)
H(7)
H(8)
H(9)
H(10)
H(11)
H(12)
H(13)
H(14)
H(15)
H(16)
H(17)
H(18)
H(19)
H(20)
H(21)
H(22)
02253-005
2
NORMALIZED OUTPUT
1
Min
150
Figure 5. FIR Filter Impulse Response—Baseband Mode
Rev. C | Page 8 of 40
Upper
Coefficient
H(43)
H(42)
H(41)
H(40)
H(39)
H(38)
H(37)
H(36)
H(35)
H(34)
H(33)
H(32)
H(31)
H(30)
H(29)
H(28)
H(27)
H(26)
H(25)
H(24)
H(23)
Integer
Value
10
0
−31
0
69
0
−138
0
248
0
−419
0
678
0
−1083
0
1776
0
−3282
0
10,364
16,384
AD9772A
ABSOLUTE MAXIMUM RATINGS
Table 6.
Parameter
AVDD, DVDD, CLKVDD,
PLLVDD
AVDD, DVDD, CLKVDD,
PLLVDD
ACOM, DCOM,
CLKCOM, PLLCOM
REFIO, REFLO, FSADJ,
SLEEP
IOUTA, IOUTB
With Respect to
ACOM, DCOM,
CLKCOM, PLLCOM
AVDD, DVDD,
CLKVDD, PLLVDD
ACOM, DCOM,
CLKCOM, PLLCOM
ACOM
DB0 to DB13, MOD0,
MOD1, PLLLOCK
CLK+, CLK−
DCOM
DIV0, DIV1, RESET
CLKCOM
LPF
PLLCOM
Junction Temperature
Storage Temperature
Lead Temperature
(10 sec)
ACOM
CLKCOM
Rating
−0.3 V to +4.0 V
−4.0 V to +4.0 V
−0.3 V to +0.3 V
−0.3 V to
AVDD + 0.3 V
−1.0 V to
AVDD + 0.3 V
−0.3 V to
DVDD + 0.3 V
−0.3 V to
CLKVDD + 0.3 V
−0.3 V to
CLKVDD + 0.3 V
−0.3 V to
PLLVDD + 0.3 V
125°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 7. Thermal Resistance
Package Type
48-Lead LQFP
ESD CAUTION
Rev. C | Page 9 of 40
θJA
91
θJC
28
Unit
°C/W
AD9772A
ACOM
REFLO
ACOM
FSADJ
REFIO
IOUTB
IOUTA
ACOM
AVDD
DVDD
AVDD
DVDD
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
DCOM
DCOM 2
1
36 SLEEP
PIN 1
IDENTIFIER
35 LPF
(MSB) DB13 3
DB12 4
34 PLLVDD
33 PLLCOM
DB11 5
DB10 6
32 CLKVDD
AD9772A
31 CLKCOM
TOP VIEW
(Not to Scale)
DB9 7
DB8 8
30 CLK–
29 CLK+
DB7 9
28 DIV0
DB6 10
27 DIV1
DB5 11
26 RESET
DB4 12
25 PLLLOCK
02253-006
NC
NC
DVDD
DVDD
MOD1
DCOM
DCOM
MOD0
(LSB) DB0
NC = NO CONNECT
DB2
DB1
DB3
13 14 15 16 17 18 19 20 21 22 23 24
Figure 6. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
1, 2, 19, 20
3
4 to 15
16
17
Mnemonic
DCOM
DB13
DB12 to DB1
DB0
MOD0
18
MOD1
23, 24
21, 22, 47, 48
25
NC
DVDD
PLLLOCK
26
RESET
27, 28
29
30
31
32
33
34
DIV1, DIV0
CLK+
CLK−
CLKCOM
CLKVDD
PLLCOM
PLLVDD
35
LPF
36
37, 41, 44
38
SLEEP
ACOM
REFLO
Description
Digital Common.
Most Significant Data Bit (MSB).
Data Bit 1 to Data Bit 12.
Least Significant Data Bit (LSB).
Digital High-Pass Filter Response. Active high. This pin invokes the digital high-pass filter response (that is,
half-wave digital mixing mode). Note that quarter-wave digital mixing occurs if this pin and the MOD1 pin
are set high.
Zero-Stuffing Mode. Active high. This pin invokes zero-stuffing mode. Note that quarter-wave digital mixing
occurs if this pin and the MOD0 pin are set high.
No Connect. Leave open.
Digital Supply Voltage (3.1 V to 3.5 V).
Lock Signal of the Phase-Lock Loop. This pin provides the lock signal of the phase-lock loop when the PLL
clock multiplier is enabled, and provides the 1× clock output when the PLL clock multiplier is disabled. High
indicates that PLL is locked to the input clock. The maximum fanout is 1 (that is, <10 pF).
Internal Divider Reset. This pin can reset the internal driver to synchronize the internal 1× clock to the input
data and/or multiple AD9772A devices. The reset is initiated if this pin is momentarily brought high when
PLL is disabled.
PLL Prescaler Divide Ratio. DIV1 and DIV0 set the prescaler divide ratio of the PLL (refer to Table 10).
Noninverting Input to Differential Clock. Bias this pin to the midsupply (that is, CLKVDD/2).
Inverting Input to Differential Clock. Bias this pin to the midsupply (that is, CLKVDD/2).
Clock Input Common.
Clock Input Supply Voltage (3.1 V to 3.5 V).
Phase-Lock Loop Common.
Phase-Lock Loop (PLL) Supply Voltage (3.1 V to 3.5 V). To disable the PLL clock multiplier, connect PLLVDD to
PLLCOM.
PLL Loop Filter Node. This pin should be left as a no connect (open) unless the DAC update rate is less than
10 MSPS, in which case a series RC should be connected from LPF to PLLVDD as indicated in Figure 61.
Power-Down Control Input. Active high. When this pin is not used, connect it to ACOM.
Analog Common.
Reference Ground When Internal 1.2 V Reference Is Used. Connect this pin to AVDD to disable the internal
reference.
Rev. C | Page 10 of 40
AD9772A
Pin No.
39
Mnemonic
REFIO
40
42
43
45, 46
FSADJ
IOUTB
IOUTA
AVDD
B
Description
Reference Input/Output. This pin serves as the reference input when the internal reference is disabled (that
is, when REFLO is tied to AVDD), or it serves as the 1.2 V reference output when the internal reference is
activated (that is, when REFLO is tied to ACOM). If the internal reference is activated, a 0.1 μ F capacitor to
ACOM is required.
Full-Scale Current Output Adjust.
Complementary DAC Current Output. Full-scale current is selected when all data bits are 0s.
DAC Current Output. Full-scale current is selected when all data bits are 1s.
Analog Supply Voltage (3.1 V to 3.5 V).
Rev. C | Page 11 of 40
AD9772A
TERMINOLOGY
Linearity Error (Also Called Integral Nonlinearity or INL)
Linearity error is defined as the maximum deviation of the
actual analog output from the ideal output and is determined by
a straight line drawn from zero to full scale.
Settling Time
Settling time is the time required for the output to reach and
remain within a specified error band about its final value. It is
measured from the start of the output transition.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normalized to
full scale that is associated with a 1 LSB change in digital input code.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV-s.
Monotonicity
A DAC is monotonic if the output either increases or remains
constant as the digital input increases.
Offset Error
Offset error is the deviation of the output current from the ideal
of zero. For IOUTA, 0 mA output is expected when the inputs are all
0s. For IOUTB, 0 mA output is expected when all inputs are set to 1s.
B
Gain Error
Gain error is the difference between the actual and ideal output
span. The actual span is determined by the output when all inputs
are set to 1s minus the output when all inputs are set to 0s.
Output Compliance Range
The output compliance range is the range of allowable voltage
at the output of a current-output DAC. Operation beyond the
maximum compliance limits may cause either output stage
saturation or breakdown, resulting in nonlinear performance.
Temperature Drift
Temperature drift is specified as the maximum change from the
ambient (25°C) value to the value at either TMIN or TMAX. For offset
and gain drift, the drift is reported in ppm of full-scale range (FSR)
per °C. For reference drift, the drift is reported in ppm per °C.
Power Supply Rejection
Power supply rejection is the maximum change in the full-scale
output as the supplies are varied from minimum to maximum
specified voltages.
Spurious-Free Dynamic Range
Spurious-free dynamic range is the difference, in decibels,
between the rms amplitude of the output signal and the peak
spurious signal over the specified bandwidth.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first six harmonic
components to the rms value of the measured fundamental. It is
expressed as a percentage or in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
Pass Band
Pass band is the frequency band in which any input applied
therein passes unattenuated to the DAC output.
Stop-Band Rejection
Stop-band rejection is the amount of attenuation of a frequency
outside the pass band applied to the DAC relative to a full-scale
signal applied at the DAC input within the pass band.
Group Delay
Group delay is the number of input clocks between an impulse
applied at the device input and the peak DAC output current.
Impulse Response
Impulse response is the response of the device to an impulse
applied to the input.
Adjacent-Channel Power Ratio (ACPR)
ACPR is a ratio, in dBc, between the measured power within a
channel relative to its adjacent channel.
Rev. C | Page 12 of 40
AD9772A
CH1
FROM HP8644A
SIGNAL GENERATOR
HP8130
PULSE GENERATOR
CH2
EXTERNAL INPUT
3.3V
CLK–
EXTERNAL
CLOCK
1×/2×
DIV1
DIV0
PLLCOM
PLLCLOCK
MULTIPLIER
LPF
PLLVDD
TO FSEA30
SPECTRUM
MINI-CIRCUITS
ANALYZER
T1-1T
2×/4×
IOUTA
DIGITAL
DATA
EDGETRIGGERED
LATCHES
2× FIR
INTERPOLATION
FILTER
ZERO
STUFF
MUX
14-BIT DAC
100Ω
IOUTB
0.1µF
1.2V REFERENCE
AND CONTROL AMP
SLEEP
DCOM
DVDD
3.3V
ACOM AVDD
REFLO
REFIO
FSADJ
50Ω
50Ω
20pF
20pF
1.91kΩ
02253-007
AWG2021
OR
DG2020
1×
CLOCK DISTRIBUTION
AND MODE SELECT
FILTER
MUX
CONTROL
CONTROL
PLLLOCK
AD9772A
CLK+
RESET
CLKVDD
CLKCOM
MOD1
1kΩ
MOD0
1kΩ
3.3V
Figure 7. Basic AC Characterization Test Setup
Rev. C | Page 13 of 40
AD9772A
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 3.3 V, CLKDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA. PLL disabled.
IN-BAND
OUT-OF-BAND
0
–20
–20
AMPLITUDE (dBm)
–40
–60
–80
–60
40
60
80
100
120
–100
Figure 8. Single-Tone Spectral Characteristics @ fDATA = 65 MSPS with fOUT = fDATA/3
50
0
fOUT (MHz)
100
150
02253-011
20
02253-008
0
fOUT (MHz)
Figure 11. Single-Tone Spectral Characteristics @ fDATA = 78 MSPS with fOUT = fDATA/3
90
90
0dBFS
85
–6dBFS
85
–6dBFS
80
80
75
SFDR (dBc)
70
–12dBFS
65
75
70
–12dBFS
0dBFS
65
60
60
55
55
50
50
5
10
15
20
25
30
fOUT (MHz)
0
02253-009
0
5
10
15
20
25
30
35
02253-012
SFDR (dBc)
–40
–80
–100
35
fOUT (MHz)
Figure 12. In-Band SFDR vs. fOUT @ fDATA = 78 MSPS
Figure 9. In-Band SFDR vs. fOUT @ fDATA = 65 MSPS
70
70
–6dBFS
–6dBFS
65
65
0dBFS
60
60
55
AMPLITUDE (dBm)
–12dBFS
50
45
45
35
35
0
5
10
15
20
25
fOUT (MHz)
30
–12dBFS
50
40
30
0dBFS
55
40
30
02253-010
SFDR (dBc)
OUT-OF-BAND
02253-013
AMPLITUDE (dBm)
IN-BAND
0
0
5
10
15
20
25
30
fOUT (MHz)
Figure 10. Out-of-Band SFDR vs. fOUT @ fDATA = 65 MSPS
Figure 13. Out-of-Band SFDR vs. fOUT @ fDATA = 78 MSPS
Rev. C | Page 14 of 40
AD9772A
90
IN-BAND
OUT-OFBAND
–6dBFS
85
–20
80
–3dBFS
75
–40
IMD (dBc)
AMPLITUDE (dBm)
0
–60
0dBFS
70
65
60
–80
100
50
150
fOUT (MHz)
200
250
300
50
0
5
10
15
20
25
30
fOUT (MHz)
02253-017
0
02253-014
55
–100
Figure 17. Third-Order IMD Products vs. fOUT @ fDATA = 65 MSPS
Figure 14. Single-Tone Spectral Characteristics @ fDATA = 160 MSPS
with fOUT = fDATA/3
90
90
85
85
–6dBFS
0dBFS
80
80
–3dBFS
75
75
IMD (dBc)
70
–12dBFS
65
65
60
60
55
55
10
20
30
40
50
60
fOUT (MHz)
02253-015
0
0
5
10
15
20
25
30
35
fOUT (MHz)
02253-018
50
50
Figure 18. Third-Order IMD Products vs. fOUT @ fDATA = 78 MSPS
Figure 15. In-Band SFDR vs. fOUT @ fDATA = 160 MSPS
70
90
65
85
60
80
–6dBFS
–3dBFS
75
IMD (dBc)
55
–6dBFS
50
0dBFS
45
70
65
0dBFS
60
40
–12dBFS
55
35
50
30
0
10
20
30
40
50
60
fOUT (MHz)
70
02253-016
AMPLITUDE (dBm)
0dBFS
70
Figure 16. Out-of-Band SFDR vs. fOUT @ fDATA = 160 MSPS
0
10
20
30
40
50
60
70
fOUT (MHz)
Figure 19. Third-Order IMD Products vs. fOUT @ fDATA = 160 MSPS
Rev. C | Page 15 of 40
02253-019
AMPLITUDE (dBm)
–6dBFS
AD9772A
90
90
85
85
fDATA = 65MSPS
–3dBFS
fDATA = 160MSPS
80
80
75
75
IMD (dBc)
IMD (dBc)
0dBFS
fDATA = 78MSPS
70
–6dBFS
70
65
60
65
–10
AOUT (dBFS)
–15
–5
0
50
3.0
02253-020
60
–20
Figure 20. Third-Order IMD Products vs. AOUT @ fOUT = fDAC/11
3.1
3.2
3.3
AVDD (V)
3.4
3.5
3.6
02253-023
55
Figure 23. Third-Order IMD Products vs. AVDD @ fOUT = 10 MHz,
fDAC = 320 MSPS
90
90
85
85
80
75
75
fDATA = 160MSPS
70
fDATA = 65MSPS
65
70
65
60
60
55
55
50
–20
–15
–10
–5
0
AOUT (dBFS)
75
125
175
fDAC (MHz)
Figure 24. SNR vs. fDAC @ fOUT = 10 MHz
90
90
85
85
–3dBFS
80
fDATA = 78MSPS
fDATA = 65MSPS
–6dBFS
0dBFS
70
65
75
70
60
60
55
55
3.2
3.3
AVDD (V)
3.4
3.5
3.6
50
–40
02253-022
3.1
fDATA = 160MSPS
65
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 22. SFDR vs. AVDD @ fOUT = 10 MHz, fDAC = 320 MSPS
Figure 25. In-Band SFDR vs. Temperature @ fOUT = fDATA/11
Rev. C | Page 16 of 40
02253-025
SFDR (dBc)
80
75
SFDR (dBc)
PLL ON, OPTIMUM DIV0/DIV1 SETTINGS
50
25
Figure 21. Third-Order IMD Products vs. AOUT @ fOUT = fDAC/5
50
3.0
PLL OFF
02253-024
SNR (dBc)
80
02253-021
IMD (dBc)
fDATA = 78MSPS
AD9772A
THEORY OF OPERATION
FUNCTIONAL DESCRIPTION
Table 9. Digital Modes
Figure 26 shows a simplified block diagram of the AD9772A.
The AD9772A is a complete 2× oversampling, 14-bit DAC that
includes a 2× interpolation filter, a phase-locked loop (PLL)
clock multiplier, and a 1.20 V band gap voltage reference.
Although the AD9772A digital interface can support input data
rates as high as 160 MSPS, its internal DAC can operate up to
400 MSPS, thus providing direct IF conversion capabilities.
The 14-bit DAC provides two complementary current outputs
whose full-scale current is determined by an external resistor.
The AD9772A features a flexible, low jitter differential clock
input, providing excellent noise rejection while accepting a sine
wave input. An on-chip PLL clock multiplier produces all of the
necessary synchronized clocks from an external reference clock
source. Separate supply inputs are provided for each functional
block to ensure optimum noise and distortion performance. A
sleep mode is also included for power savings.
Digital
Mode
Baseband
Baseband
Direct IF
Direct IF
CLKCOM CLKVDD MOD0 MOD1 RESET PLLLOCK DIV0 DIV1
AD9772A
CLOCK DISTRIBUTION
AND MODE SELECT
CLK–
1×
DATA
INPUTS
(DB13 TO
DB0)
1× /2×
EDGETRIGGERED
LATCHES
FILTER
MUX
CONTROL CONTROL
2× FIR
INTERPOLATION
FILTER
PLL CLOCK
MULTIPLIER
IOUTA
14-BIT DAC
1.2V REFERENCE
AND CONTROL AMP
SLEEP
DCOM DVDD
ACOM AVDD
LPF
PLLVDD
2× /4×
ZERO
STUFF
MUX
PLLCOM
REFLO
IOUTB
MOD1
0
1
0
1
Digital
Filter
Low
Low
High
High
ZeroStuffing
No
Yes
No
Yes
For applications requiring the highest dynamic range over a
wide bandwidth, users should consider operating the AD9772A
in a baseband mode. Although the zero-stuffing option can be
used in this mode, the ratio of the signal to the image power
will be reduced.
For applications requiring the synthesis of IF signals, users
should consider operating the AD9772A in a direct IF mode. In
this case, the zero-stuffing option should be considered when
synthesizing and selecting IFs beyond the input data rate, fDATA.
If the reconstructed IF falls below fDATA, the zero-stuffing option
may or may not be beneficial. Note that the dynamic range (that
is, SNR/SFDR) can be optimized by disabling the PLL clock
multiplier (that is, by connecting PLLVDD to PLLCOM) and by
using an external low-jitter clock source operating at the DAC
update rate, fDAC.
2× Interpolation Filter Description
REFIO
FSADJ
02253-026
CLK+
MOD0
0
0
1
1
Figure 26. Simplified Functional Block Diagram
Preceding the 14-bit DAC is a 2× digital interpolation filter that
can be configured for a low-pass (that is, baseband mode) or
high-pass (that is, direct IF mode) response. The input data is
latched into the edge-triggered input latches on the rising edge
of the differential input clock, as shown in Figure 2, and then
interpolated by a factor of 2 by the digital filter. For traditional
baseband applications, the 2× interpolation filter has a low-pass
response. For direct IF applications, the filter response can be
converted into a high-pass response to extract the higher image.
The output data of the 2× interpolation filter can update the
14-bit DAC directly or undergo a zero-stuffing process to increase
the DAC update rate by another factor of 2. This action enhances
the relative signal level and pass-band flatness of the higher
frequency images.
DIGITAL MODES OF OPERATION
The AD9772A features four modes of operation controlled by
the digital inputs, MOD0 and MOD1. MOD0 controls the 2×
digital filter response (that is, low-pass or high-pass), and
MOD1 controls the zero-stuffing option. The appropriate mode
to select (see Table 9) depends on whether the application
requires the reconstruction of a baseband or IF signal.
The 2× interpolation filter is based on a 43-tap, half-band,
symmetric FIR topology that can be configured for a low- or
high-pass response, depending on the state of the MOD0
control input. The low-pass response is selected with MOD0
low, and the high-pass response is selected with MOD0 high.
The low-pass frequency and the impulse response of the halfband interpolation filter are shown in Figure 4 and Figure 5,
and the idealized filter coefficients are listed in Table 5. Note
that the impulse response of a FIR filter is also represented by
its idealized filter coefficients.
The 2× interpolation filter essentially multiplies the input data rate
to the DAC by a factor of 2, relative to its original input data rate,
while reducing the magnitude of the first image associated with
the original input data rate occurring at fDATA − fFUNDAMENTAL. As a
result of the 2× interpolation, the digital filter frequency response is
uniquely defined over its Nyquist zone of dc to fDATA, with mirror
images occurring in adjacent Nyquist zones.
The benefits of an interpolation filter are clearly seen in
Figure 27, which shows an example of the frequency and time
domain representation of a discrete time sine wave signal before
and after it is applied to the 2× digital interpolation filter in a
low-pass configuration. Images of the sine wave signal appear
around multiples of the input data rate (that is, fDATA) of the DAC,
as predicted by sampling theory. These undesirable images also
appear at the output of a reconstruction DAC, although they are
attenuated by the sin(x)/x roll-off response of the DAC.
Rev. C | Page 17 of 40
AD9772A
representation for a high-pass response of a discrete time sine
wave. This action can also be modeled as a half-wave digital
mixing process in which the impulse response of the low-pass
filter is digitally mixed with a square wave having a frequency of
exactly fDATA/2. Because the even coefficients have an integer
value of 0 (see Table 5), this process simplifies into inverting the
center coefficient of the low-pass filter (that is, inverting H(18)).
Note that this also corresponds to inverting the peak of the
impulse response shown in Figure 4. The resulting high-pass
frequency response becomes the frequency inverted mirror
image of the low-pass filter response shown in Figure 5.
In many band-limited applications, the images from the
reconstruction process must be suppressed by an analog filter
following the DAC. The complexity of this analog filter is typically
determined by the proximity of the desired fundamental to the
first image and the required amount of image suppression.
Adding to the complexity of this analog filter is the requirement
of compensating for the sin(x)/x response of the DAC.
Referring to Figure 27, the new first image associated with the
higher data rate of the DAC after interpolation is pushed out
further relative to the input signal, because it now occurs at 2×
fDATA − fFUNDAMENTAL. The old first image associated with the
lower DAC data rate before interpolation is suppressed by the
digital filter. As a result, the transition band for the analog
reconstruction filter is increased, thus reducing the complexity
of the analog filter. Furthermore, the value of the sin(x)/x rolloff divided by the original input data pass band (that is, dc to
fDATA/2) is significantly reduced.
Note that the new first image occurs at fDATA + fFUNDAMENTAL. A
reduced transition region of 2 × fFUNDAMENTAL exists for image
selection, thus mandating that the fFUNDAMENTAL be placed
sufficiently high for practical filtering purposes in direct IF
applications. In addition, the lower sideband images occurring
at fDATA − fFUNDAMENTAL and its multiples (that is, N × fDATA −
fFUNDAMENTAL) experience a frequency inversion while the upper
sideband images occurring at fDATA + fFUNDAMENTAL and its multiples
(that is, N × fDATA + fFUNDAMENTAL) do not.
As previously mentioned, the 2× interpolation filter can be
converted into a high-pass response, thus suppressing the fundamental while passing the original first image occurring at
fDATA − fFUNDAMENTAL. Figure 28 shows the time and frequency
1/ 2 × fDATA
TIME
DOMAIN
1/fDATA
fFUNDAMENTAL
FIRST IMAGE
NEW
fFUNDAMENTAL DIGITAL FIRST IMAGE
FILTER
RESPONSE
DAC SIN(x)/x
RESPONSE
FREQUENCY
DOMAIN
fDATA
2 × fDATA
fDATA
2 × fDATA
SUPPRESSED
FIRST IMAGE
2× INTERPOLATION
FILTER
2×
fDATA
2 × fDATA
2 × fDATA
DAC
02253-027
INPUT DATA
LATCH
fDATA
Figure 27. Time and Frequency Domain Example of Low-Pass 2× Digital Interpolation Filter
1/2 × fDATA
TIME
DOMAIN
1/fDATA
fFUNDAMENTAL
UPPER AND
LOWER IMAGE
FIRST IMAGE
DIGITAL
FILTER
RESPONSE
DAC SIN(x)/x
RESPONSE
FREQUENCY
DOMAIN
fDATA
2 × fDATA
fDATA
2 × fDATA
fDATA
2 × fDATA
SUPPRESSED
fFUNDAMENTAL
2× INTERPOLATION
FILTER
2×
fDATA
2 × fDATA
DAC
Figure 28. Time and Frequency Domain Example of High-Pass 2× Digital Interpolation Filter
Rev. C | Page 18 of 40
02253-028
INPUT DATA
LATCH
AD9772A
Zero-Stuffing Option Description
As shown in Figure 29, a zero or null in the frequency response
(after interpolation and DAC reconstruction) occurs at the final
DAC update rate (that is, 2× fDATA) due to the inherent sin(x)/x
roll-off response of the DAC. In baseband applications, this rolloff in the frequency response may not be as problematic
because much of the desired signal energy remains below
fDATA/2 and the amplitude variation is not as severe. However, in
direct IF applications interested in extracting an image above
fDATA/2, this roll-off may be problematic due to the increased
pass-band amplitude variation as well as the reduced signal
level of the higher images.
0
WITH
ZERO-STUFFING
WITHOUT
ZERO-STUFFING
–20
It is important to realize that the zero-stuffing option by itself
does not change the location of the images, but rather changes
their signal level, amplitude flatness, and relative weighting. For
instance, in the previous example, the pass-band amplitude
flatness of the lower and upper sideband images centered
around fDATA are improved to 0.14 dB and 0.24 dB, respectively,
while the signal level changes to −6.5 dBFS and −7.5 dBFS. The
lower or upper sideband image centered around 3 × fDATA
exhibit an amplitude flatness of 0.77 dB and 1.29 dB with signal
levels of approximately −14.3 dBFS and −19.2 dBFS.
PLL CLOCK MULTIPLIER OPERATION
3.0
3.5
4.0
Figure 29. Effects of Zero-Stuffing on the Sin(x)/x Response of the DAC
For instance, if the digital data into the AD9772A represents a
baseband signal centered around fDATA/4 with a pass band of
fDATA/10, the reconstructed baseband signal output from the
AD9772A experiences only a 0.18 dB amplitude variation over
its pass band, with the first image occurring at 7/4 × fDATA and
exhibiting 17 dB of attenuation relative to the fundamental.
However, if the high-pass filter response is selected, the AD9772A
produces pairs of images at [(2N + 1) × fDATA] ± fDATA/4, where
N = 0, 1, and so on. Note that due to the sin(x)/x response of the
DAC, only the lower or upper sideband images centered around
fDATA may be useful, although they are attenuated by −2.1 dB and
−6.54 dB and have a pass-band amplitude roll-off of 0.6 dB and
1.3 dB, respectively.
To improve on the pass-band flatness of the desired image
and/or to extract higher images (that is, 3 × fDATA ± fFUNDAMENTAL),
the zero-stuffing option should be employed by bringing the
MOD1 pin high. This option increases the effective DAC
update rate by another factor of 2 because a midscale sample
(that is, 10 0000 0000 0000) is inserted after every data sample
originating from the 2× interpolation filter. A digital multiplexer
switching at a rate of 4 × fDATA between the interpolation filter
output and a data register containing the midscale data sample is
used as shown in Figure 28 to implement this option. Therefore,
the DAC output is now forced to return to its differential midscale
current value (that is, IOUTA − IOUTB at 0 mA) after reconstructing
each data sample from the digital filter.
CLK+ CLK–
CLKVDD PLLLOCK
+
–
AD9772A
PHASE
DETECTOR
CLOCK
DISTRIBUTION
Rev. C | Page 19 of 40
PRESCALER
LPF
DNC
PLLVDD 2.7V
TO
3.6V
EXT/INT
CLOCK CONTROL
OUT1×
CLKCOM
CHARGE
PUMP
VCO
PLLCOM
Figure 30. Clock Multiplier with PLL Clock Multiplier Enabled
02253-030
1.5
2.0
2.5
FREQUENCY (fDATA )
DIV0
1.0
DIV1
0.5
RESET
0
BASEBAND
REGION
02253-029
–40
The phase-lock loop (PLL) clock multiplier circuitry, along with
the clock distribution circuitry, can produce the necessary
internally synchronized 1×, 2×, and 4× clocks for the edgetriggered latches, 2× interpolation filter, zero-stuffing
multiplier, and DAC. Figure 30 shows a functional block
diagram of the PLL clock multiplier, which consists of a phase
detector, a charge pump, a voltage controlled oscillator (VCO),
a prescaler, and digital control input/output. The clock
distribution circuitry generates all the internal clocks for a given
mode of operation. The charge pump and VCO are powered
from PLLVDD, and the differential clock input buffer, phase
detector, prescaler, and clock distribution circuitry are powered
from CLKVDD. To ensure optimum phase noise performance
from the PLL clock multiplier and clock distribution circuitry,
PLLVDD and CLKVDD must originate from the same clean
analog supply.
MOD0
–30
MOD1
ROLL-OFF (dBFS)
–10
The net effect is to increase the DAC update rate such that the
zero in the sin(x)/x frequency response occurs at 4 × fDATA
accompanied by a corresponding reduction in output power as
shown in Figure 29. Note that if the high-pass response of the
2× interpolation filter is also selected, this action can be
modeled as a quarter-wave digital mixing process, because this
is equivalent to digitally mixing the impulse response of the
low-pass filter with a square wave having a frequency of exactly
fDATA (that is, fDAC/4).
AD9772A
With the PLL clock multiplier enabled, PLLLOCK serves as an
active high control output that can be monitored upon system
power-up to indicate that the PLL is successfully locked to the
input clock. Note that when the PLL clock multiplier is not
locked, PLLLOCK toggles between logic high and low in an
asynchronous manner until locking is finally achieved. As a
result, it is recommended that PLLLOCK, if monitored, be
sampled several times to detect proper locking 100 ms after
power-up.
Table 10. Recommended Prescaler Divide-by-N Ratio Settings
fDATA
(MSPS)
48 to 160
24 to 100
12 to 50
6 to 25
24 to 100
12 to 50
6 to 25
3 to 12.5
MOD1
0
0
0
0
1
1
1
1
DIV1
0
0
1
1
0
0
1
1
DIV0
0
1
0
1
0
1
0
1
Divide-by-N Ratio
1
2
4
8
1
2
4
8
–10
–20
–30
–40
–50
PLL ENABLED, fDATA = 160MSPS
–60
PLL ENABLED, fDATA = 100MSPS
–70
PLL ENABLED, fDATA = 75MSPS
–80
PLL ENABLED, fDATA = 50MSPS
–90
–100
–110
PLL ENABLED, fDATA = 50MSPS
0
1
2
3
FREQUENCY OFFSET (MHz)
4
5
02253-031
Because the VCO can operate over a 96 MHz to 400 MHz
range, the prescaler divide-by-ratio following the VCO must be
set according to Table 10 for a given input data rate (that is,
fDATA) to ensure optimum phase noise and successful locking. In
general, the best phase noise performance for any prescaler
setting is achieved with the VCO operating near its maximum
output frequency of 400 MHz. Note that the divide-by-N ratio
also depends on whether the zero-stuffing option is enabled
because this option requires the DAC to operate at 4× the input
data rate. The divide-by-N ratio is set by DIV1 and DIV0.
0
Figure 31. Phase Noise of PLL Clock Multiplier with a Full-Scale Sine Wave at
Exactly fOUT = fDATA/4 for Different fDATA Settings with Optimum DIV0/DIV1
Settings Using the Rohde & Schwarz FSEA30, RBW = 30 kHz
10
–10
–30
–50
–70
–90
–110
120
122
124
126
FREQUENCY (MHz)
128
130
02253-032
The settling/acquisition time characteristics of the PLL are also
dependent on the divide-by-N ratio as well as the input data
rate. In general, the acquisition time increases with increasing
data rate (for fixed divide-by-N ratio) or with an increasing
divide-by-N ratio (for fixed input data rate).
The effects of phase noise on the AD9772A SNR performance
become more noticeable at higher reconstructed output frequencies and signal levels. Figure 31 compares the phase noise
of a full-scale sine wave at exactly fDATA/4 for different data rates
(and therefore carrier frequencies) with the optimum DIV1 and
DIV0 settings. The effects of phase noise, and its effect on a
signal’s CNR performance, become even more evident at higher
IF frequencies, as shown in Figure 32. In both instances, it is the
narrow-band phase noise that limits the CNR performance.
NOISE DENSITY (dBm/Hz)
Figure 30 shows the proper configuration used to enable the
PLL clock multiplier. In this case, the external clock source is
applied to CLK+ (and/or CLK−) and the PLL clock multiplier is
fully enabled by connecting PLLVDD to CLKVDD.
As previously stated, applications requiring input data rates
below 6 MSPS must disable the PLL clock multiplier and
provide an external reference clock. However, for applications
already containing a low phase noise (that is, low jitter) reference
clock that is twice (or four times) the input data rate, users should
consider disabling the PLL clock multiplier to achieve the best SNR
performance from the AD9772A. Note that the SFDR performance
and wideband noise performance of the AD9772A remain
unaffected with or without the PLL clock multiplier enabled.
AMPLITUDE (dBm)
The PLL clock multiplier has two modes of operation. It can be
enabled for less demanding applications, providing a reference
clock meeting the minimum specified input data rate of 6 MSPS.
Alternatively, it can be disabled for applications below this data
rate or for applications requiring higher phase noise performance.
In this case, a reference clock must be provided at twice the input
data rate (that is, 2 × fDATA) without the zero-stuffing option selected
or at four times the input data rate (that is, 4 × fDATA) with the zerostuffing option selected. Note that multiple AD9772A devices
can be synchronized in either mode if driven by the same reference
clock because the PLL clock multiplier, when enabled, ensures
synchronization. RESET can be used for synchronization if the
PLL clock multiplier is disabled.
Figure 32. Direct IF Mode Reveals Phase Noise Degradation with and
Without PLL Clock Multiplier (IF = 125 MHz and fDATA = 100 MSPS)
To disable the PLL clock multiplier, connect PLLVDD to
PLLCOM as shown in Figure 33. LPF can then remain open
because this portion of the PLL circuitry is disabled. The
Rev. C | Page 20 of 40
AD9772A
CLK+ CLK–
+
–
AD9772A
PHASE
DETECTOR
CHARGE
PUMP
LPF
CLOCK
DISTRIBUTION
PRESCALER
EXTERNAL
2× CLOCK
DATA
tLPW
tPD
tPD
DELAYED INTERNAL
1× CLOCK
tD
IOUTA OR IOUTB
DATA ENTERS INPUT
LATCHES ON THIS EDGE
Figure 34. Internal Timing of AD9772A with PLL Disabled
Figure 35 and Figure 36 illustrate the details of the RESET
function timing. The RESET pin going from a high to a low
logic level enables the 1× clock output generated by the
PLLLOCK pin. If RESET goes low before the rising edge of the
2× clock as shown in Figure 35, PLLLOCK goes high on the
following edge of the 2× clock. If RESET goes from a high to a
low logic level 600 ps or later following the rising edge of the 2×
clock, as shown in Figure 36, there is a delay of one 2× clock
cycle before PLLLOCK goes high. In either case, as long as
RESET remains low, PLLLOCK changes state on every rising
edge of the 2× clock. As previously stated, the rising edge of the
2× clock immediately preceding the rising edge of PLLLOCK
latches data into the AD9772A input latches.
[T
]
EXTERNAL
1× CLOCK
1
VCO
PLLCOM
2
T
T
PLLLOCK
MOD1 MOD0 RESET
DIV1
DIV0
02253-033
T
CLKCOM
RESET
3
Figure 33. Clock Multiplier with PLL Clock Multiplier Disabled
CH1 2.00VΩ CH2 2.00VΩ M 10.0ns CH3 2.00VΩ
SYNCHRONIZATION OF CLOCK/DATA USING
RESET WITH PLL DISABLED
Figure 35. RESET Timing with PLL Disabled
[T
The relationship between the internal and external clocks in
this mode is shown in Figure 34. A clock at the output update
data rate (2× the input data rate) must be applied to the CLK+
and CLK− inputs. Internal dividers create the internal 1× clock
necessary for the input latches. With the PLL disabled, a delayed
version of the 1× clock is present at the PLLLOCK pin. The
DAC latch is updated on the rising edge of the external 2× clock
that corresponds to the rising edge of the 1× clock. Updates to
the input data should be synchronized to this rising edge as
shown in Figure 34. To ensure this synchronization, a Logic 1
should be momentarily applied to the RESET pin on power-up
before CLK+/CLK− is applied. Momentarily applying a Logic 1
to the RESET pin brings the 1× clock at PLLLOCK to a Logic 1.
On the next rising edge of the 2× clock, the 1× clock goes to
02253-034
LOAD-DEPENDENT,
DELAYED 1× CLOCK
AT PLLLOCK
PLLVDD
EXT/INT
CLOCK CONTROL
OUT1×
DIGITAL DATA IN
]
EXTERNAL
2× CLOCK
1
T
PLLLOCK
2
T
T
RESET
3
CH1 2.00VV CH2 2.00VV M 10.0ns CH4
CH3 2.00VΩ
1.20V
02253-036
CLKVDD PLLLOCK
Logic 0. The following rising edge of the 2× clock causes the 1×
clock to go to Logic 1 again and updates the data in both of the
input latches.
02253-035
differential clock input should be driven with a reference clock
that is twice the data input rate in baseband applications, or that
is four times the data input rate in direct IF applications in
which the quarter-wave mixing option is employed (that is,
MOD1 and MOD0 active high). The clock distribution circuitry
remains enabled, providing a 1× internal clock at PLLLOCK.
Digital input data is latched into the AD9772A on every other
rising edge of the differential clock input. The rising edge that
corresponds to the input latch immediately precedes the rising
edge of the 1× clock at PLLLOCK. Adequate setup and hold
times for the input data, as shown in Figure 3, should be
allowed. Note that enough delay is present between
CLK+/CLK− and the data input latch to cause the minimum
setup time for input data to be negative. This is noted in the
Digital Filter Specifications section. PLLLOCK contains a
relatively weak driver output, with its output delay (tOD)
sensitive to output capacitance loading. Therefore, PLLLOCK
should be buffered for fanouts greater than 1 and/or for load
capacitance greater than 10 pF. If a data timing issue exists
between the AD9772A and its external driver device, the
1× clock appearing at PLLLOCK can be inverted via an external
gate to ensure proper setup and hold time.
Figure 36. RESET Timing with PLL Disabled and Insufficient Setup Time
Rev. C | Page 21 of 40
AD9772A
where:
DAC OPERATION
The 14-bit DAC, along with the 1.2 V reference and reference
control amplifier, is shown in Figure 37. The DAC consists of a
large PMOS current source array capable of providing up to
20 mA of full-scale current, IOUTFS. The array is divided into 31
equal currents that make up the five most significant bits
(MSBs). The next four bits, or middle bits, consist of 15 equal
current sources whose values are 1/16th of an MSB current
source. The remaining LSBs are binary-weighted fractions of
the middle bits’ current sources. All of these current sources are
switched to one of the two output nodes (that is, IOUTA or IOUTB) via
the PMOS differential current switches. Implementing the middle
and lower bits with current sources instead of an R-2R ladder
enhances its dynamic performance for multitone or low amplitude
signals and helps maintain the high output impedance of the DAC.
2.7V TO 3.6V
REFLO
AVDD
REFIO
0.1µF
RSET
2kΩ
ACOM
250pF
1.2V REF
SEGMENTED
SWITCHES
The two current outputs typically drive a resistive load directly
or via a transformer. If dc coupling is required, IOUTA and IOUTB
should be directly connected to matching resistive loads, RLOAD,
that are tied to analog common, ACOM. Note that RLOAD can
represent the equivalent load resistance seen by IOUTA or IOUTB, as
would be the case in a doubly terminated 50 Ω or 75 Ω cable.
The single-ended voltage output appearing at the IOUTA and IOUTB
nodes is simply
VOUTA = IOUTA × RLOAD
(5)
VOUTB = IOUTB × RLOAD
(6)
Note that the full-scale value of VOUTA and VOUTB should not
exceed the specified output compliance range of 1.25 V to
prevent signal compression. To maintain optimum distortion
and linearity performance, the maximum voltages at VOUTA and
VOUTB should not exceed ±500 mV p-p.
The differential voltage, VDIFF, appearing across IOUTA and IOUTB is
B
VDIFF = (IOUTA − IOUTB) × RLOAD
IOUTA
IOUTA
LSB
SWITCHES
IOUTB
IOUTB
B
RLOAD
RLOAD
02253-037
INTERPOLATED
DIGITAL DATA
(7)
Substituting the values of IOUTA, IOUTB, and IREF, VDIFF can be
expressed as
VDIFF = VOUTA – VOUTB
VDIFF = [(2 DAC CODE − 16,383)/16,384] ×
(32 × RLOAD/RSET) × VREFIO
AD9772A
Figure 37. Block Diagram of Internal DAC, 1.2 V Reference, and Reference
Control Circuits
The full-scale output current is regulated by the reference
control amplifier and can be set from 2 mA to 20 mA via an
external resistor, RSET, as shown in Figure 37. RSET, in
combination with both the reference control amplifier and
voltage reference, REFIO, sets the reference current, IREF, which
is mirrored to the segmented current sources with the proper
scaling factor. The full-scale current, IOUTFS, is exactly 32 times
the value of IREF.
DAC TRANSFER FUNCTION
The AD9772A provides complementary current outputs, IOUTA
and IOUTB. IOUTA provides a near full-scale current output, IOUTFS,
when all bits are high (that is, DAC CODE = 16,383), whereas
IOUTB, the complementary output, provides no current. The
current output appearing at IOUTA and IOUTB is a function of both
the input code and IOUTFS and can be expressed as
B
B
B
IOUTA = (DAC CODE/16,384) × IOUTFS
(1)
IOUTB = (16,383 − DAC CODE)/16,384 × IOUTFS
(2)
where DAC CODE = 0 to 16,383 (that is, decimal representation).
As previously mentioned, IOUTFS is a function of the reference
current (IREF), which is nominally set by a reference voltage
(VREFIO) and an external resistor (RSET). It can be expressed as
IOUTFS = 32 × IREF
(4)
B
CURRENT
SOURCE
ARRAY
FSADJ
IREF
IREF = VREFIO/RSET
(8)
The last two equations highlight some of the advantages of
operating the AD9772A differentially. First, the differential
operation helps cancel common-mode error sources, such as
noise, distortion, and dc offsets, associated with IOUTA and IOUTB.
Second, the differential code-dependent current and
subsequent voltage, VDIFF, is twice the value of the single- ended
voltage output (that is, VOUTA or VOUTB), thus providing twice the
signal power to the load.
B
Note that the gain drift temperature performance for a singleended (VOUTA and VOUTB) or differential output (VDIFF) of the
AD9772A can be enhanced by selecting temperature tracking
resistors for RLOAD and RSET due to their ratiometric relationship,
as shown in Equation 8.
B
REFERENCE OPERATION
The AD9772A contains an internal 1.20 V band gap reference
that can easily be disabled and overridden by an external
reference. REFIO serves as either an output or input, depending on whether the internal or external reference is selected. If
REFLO is tied to ACOM, as shown in Figure 38, the internal
reference is activated, and REFIO provides a 1.20 V output. In
this case, the internal reference must be compensated externally
with a ceramic chip capacitor of 0.1 μF or greater from REFIO
to REFLO. If any additional loading is required, REFIO should
be buffered with an external amplifier having an input bias
current less than 100 nA.
(3)
Rev. C | Page 22 of 40
AD9772A
2.7V TO 3.6V
OPTIONAL
EXTERNAL
REF BUFFER
REFLO
AVDD
250p F
1.2V REF
REFIO
ADDITIONAL
LOAD
0.1µF
along with the AD1580 voltage reference. Note that because the
input impedance of REFIO does interact with and load the
digital potentiometer wiper to create a slight nonlinearity in the
programmable voltage divider ratio, a digital potentiometer
with 10 kΩ or less resistance is recommended.
CURRENT
SOURCE
ARRAY
FSADJ
2.7V TO 3.6V
AD9772A
10kΩ
Figure 38. Internal Reference Configuration
1.2V
The internal reference can be disabled by connecting REFLO to
AVDD. In this case, an external 1.2 V reference, such as the
AD1580, can be applied to REFIO as shown in Figure 39. The
external reference can provide either a fixed reference voltage to
enhance accuracy and drift performance or a varying reference
voltage to improve gain control. Note that the 0.1 μF compensation
capacitor is not required because the internal reference is disabled
and the high input impedance of REFIO minimizes any loading
of the external reference.
2.7V TO 3.6V
REFLO
AVDD
250pF
+1.2V REF
VREFIO
AD1580
REFIO
CURRENT
SOURCE
ARRAY
FSADJ
RSET
IREF =
VREFIO/RSET
AD9772A
AD1580
AVDD
250pF
1.2V REF
REFIO
10kΩ
RSET
CURRENT
SOURCE
ARRAY
FSADJ
AD9772A
Figure 40. Single-Supply Gain Control Circuit
ANALOG OUTPUTS
The AD9772A produces two complementary current outputs,
IOUTA and IOUTB, which can be configured for single-ended or
differential operation. IOUTA and IOUTB can be converted into
complementary single-ended voltage outputs, VOUTA and VOUTB,
via a load resistor, RLOAD, as described in the DAC Transfer
Function section, by using Equation 5 through Equation 8. The
differential voltage, VDIFF, existing between VOUTA and VOUTB, can
also be converted to a single-ended voltage via a transformer or
differential amplifier configuration.
B
REFERENCE
CONTROL
AMPLIFIER
02253-039
10kΩ
REFLO
AD5220
02253-040
02253-038
2kΩ
Figure 39. External Reference Configuration
Figure 41 shows the equivalent analog output circuit of the
AD9772A, which consists of a parallel combination of PMOS
differential current switches associated with each segmented
current source. The output impedance of IOUTA and IOUTB is
determined by the equivalent parallel combination of the PMOS
switches and is typically 200 kΩ in parallel with 3 pF. Due to the
nature of a PMOS device, the output impedance is also slightly
dependent on the output voltage (that is, VOUTA and VOUTB) and,
to a lesser extent, the analog supply voltage, AVDD, and fullscale current, IOUTFS. Although the signal dependency of the
output impedance can be a source of dc nonlinearity and ac
linearity (that is, distortion), its effects can be limited if certain
precautions are taken.
B
The AD9772A also contains an internal control amplifier that is
used to regulate the DAC’s full-scale output current, IOUTFS. The
control amplifier is configured as a V-I converter, as shown in
Figure 39, such that its current output, IREF, is determined by the
ratio of the VREFIO and an external resistor, RSET, as stated in
Equation 4. IREF is copied to the segmented current sources with
the proper scaling factor to set IOUTFS as stated in Equation 3.
The control amplifier allows a wide (10:1) adjustment span of
IOUTFS over a 2 mA to 20 mA range by setting IREF between
62.5 μA and 625 μA. The wide adjustment span of IOUTFS provides several application benefits. The first benefit relates
directly to the power dissipation of the AD9772A DAC, which
is proportional to IOUTFS (see the Power Dissipation section).
The second benefit relates to the 20 dB adjustment, which is
useful for system gain control purposes.
IREF can be controlled using the single-supply circuit shown in
Figure 40 for a fixed RSET. In this example, the internal reference is disabled, and the voltage of REFIO is varied over its
compliance range of 1.25 V to 0.10 V. REFIO can be driven by a
single-supply DAC or digital potentiometer, thus allowing IREF
to be digitally controlled for a fixed RSET. This particular example
shows the AD5220, an 8-bit serial input digital potentiometer,
AVDD
AD9772A
IOUTA
IOUTB
RLOAD
RLOAD
02253-041
REFERENCE CONTROL AMPLIFIER
Figure 41. Equivalent Analog Output Circuit
IOUTA and IOUTB also have a negative and positive voltage
compliance range. The negative output compliance threshold
of −1.0 V is set by the breakdown limits of the CMOS process.
Operation beyond this maximum limit may result in a breakdown
Rev. C | Page 23 of 40
AD9772A
of the output stage and affect the reliability of the AD9772A.
The positive output compliance range is slightly dependent on
the full-scale output current, IOUTFS. Operation beyond the
positive compliance range induces clipping of the output signal,
which severely degrades the AD9772A linearity and distortion
performance.
Operating the AD9772A with reduced voltage output swings
at IOUTA and IOUTB in a differential or single-ended output
configuration reduces the signal dependency of its output
impedance, thus enhancing distortion performance. Although
the voltage compliance range of IOUTA and IOUTB extends from
−1.0 V to +1.25 V, optimum distortion performance is achieved
when the maximum full-scale signal at IOUTA and IOUTB does not
exceed approximately 0.5 V. Using a properly selected
transformer with a grounded center tap allows the AD9772A to
provide the required power and voltage levels to different loads
while maintaining reduced voltage swings at IOUTA and IOUTB.
DC-coupled applications requiring a differential or singleended output configuration should size RLOAD accordingly. Refer
to the Output Configurations section for examples of various
output configurations.
B
produces a complementary output with the full-scale current
split between the two outputs as a function of the input code.
The digital interface is implemented using an edge-triggered
master slave latch and is designed to support an input data rate as
high as 160 MSPS. The clock can be operated at any duty cycle that
meets the specified latch pulse width, as shown in Figure 2 and
Figure 3. The setup and hold times can also be varied within the
clock cycle as long as the specified minimum times are met. The
digital inputs (excluding CLK+ and CLK−) are CMOS compatible
with its logic thresholds, VTHRESHOLD, set to approximately half the
digital positive supply (that is, DVDD or CLKVDD) or
VTHRESHOLD = DVDD/2 (±20%)
B
The most significant improvement in the AD9772A distortion
and noise performance is realized using a differential output
configuration. The common-mode error sources of both IOUTA
and IOUTB can be substantially reduced by the common-mode
rejection of a transformer or differential amplifier. These
common-mode error sources include even-order distortion
products and noise. The enhancement in distortion performance
becomes more significant as the reconstructed waveform’s
frequency content increases and/or its amplitude decreases. The
distortion and noise performance of the AD9772A is also
dependent on the full-scale current setting, IOUTFS. Although IOUTFS
can be set between 2 mA and 20 mA, selecting an IOUTFS of 20 mA
provides the best distortion and noise performance.
The internal digital circuitry of the AD9772A is capable of
operating over a digital supply range of 3.1 V to 3.5 V. As a
result, the digital inputs can also accommodate TTL levels when
DVDD is set to accommodate the maximum high level voltage
of the TTL drivers VOH(MAX). Although a DVDD of 3.3 V
typically ensures proper compatibility with most TTL logic
families, series 200 Ω resistors are recommended between the
TTL logic driver and digital inputs to limit the peak current
through the ESD protection diodes if VOH(MAX) exceeds DVDD
by more than 300 mV. Figure 42 shows the equivalent digital
input circuit for the data and control inputs.
DVDD
B
In summary, the AD9772A achieves the optimum distortion
and noise performance under the following conditions:
•
•
•
Positive voltage swing at IOUTA and IOUTB limited to 0.5 V
Differential operation
IOUTFS set to 20 mA
PLL clock multiplier disabled
B
Note that the majority of the ac characterization curves for the
AD9772A are performed with these operating conditions.
02253-042
Figure 42. Equivalent Digital Input
The AD9772A features a flexible differential clock input operating
from separate supplies (that is, CLKVDD, CLKCOM) to achieve
optimum jitter performance. The two clock inputs, CLK+ and
CLK−, can be driven from a single-ended or differential clock
source. For single-ended operation, CLK+ should be driven by a
single-ended logic source, and CLK− should be set to the logic
source’s threshold voltage via a resistor divider/capacitor network
referenced to CLKVDD as shown in Figure 43. For differential
operation, both CLK+ and CLK− should be biased to CLKVDD/2
via a resistor divider network as shown in Figure 44. An RF
transformer as shown in Figure 7 can also be used to convert a
single-ended clock input to a differential clock input.
AD9772A
DIGITAL INPUTS/OUTPUTS
The AD9772A consists of several digital input pins used for
data, clock, and control purposes. It also contains a single
digital output pin, PLLLOCK, which is used to monitor the
status of the internal PLL clock multiplier or provide a 1× clock
output. The 14-bit parallel data inputs follow standard positive
binary coding, where DB13 is the most significant bit (MSB)
and DB0 is the least significant bit (LSB). IOUTA produces a fullscale output current when all data bits are at Logic 1. IOUTB
RSERIES
CLK+
CLKVDD
1kΩ
CLK–
VTHRESHOLD
1kΩ
0.1µF
CLKCOM
02253-043
•
DIGITAL
INPUT
B
Figure 43. Single-Ended Clock Interface
Rev. C | Page 24 of 40
AD9772A
The power dissipation is directly proportional to the analog
supply current, IAVDD, and the digital supply current, IDVDD. IAVDD
is directly proportional to IOUTFS and is not sensitive to fDATA.
AD9772A
1kΩ
CLK+
1kΩ
0.1µF
Conversely, IDVDD is dependent on both the digital input
waveform and fDATA. Figure 45 shows IDVDD as a function of fullscale sine wave output ratios (fOUT/fDATA) for various update rates
with DVDD = 3.3 V. The supply current from CLKVDD and
PLLVDD is relatively insensitive to the digital input waveform
but directly proportional to the update rate, as shown in Figure 46.
CLKVDD
1kΩ
CLK–
1kΩ
CLKCOM
02253-044
0.1µF
Figure 44. Differential Clock Interface
100
fDATA = 160MSPS
90
fDATA = 125MSPS
80
70
IDVDD (mA)
The quality of the clock and data input signals is important in
achieving the optimum performance. The external clock driver
circuitry should provide the AD9772A with a low jitter clock
input, which meets the minimum/maximum logic levels while
providing fast edges. Although fast clock edges help minimize
jitter manifesting as phase noise on a reconstructed waveform,
the high gain-bandwidth product of the AD9772A differential
comparator can tolerate sine wave inputs as low as 0.5 V p-p,
with minimal degradation in its output noise floor.
fDATA = 100MSPS
60
50
fDATA = 65MSPS
40
30
fDATA = 50MSPS
20
Digital signal paths should be kept short, and run lengths
should match to avoid propagation delay mismatch. The
insertion of a low value resistor network (that is, 50 Ω to 200 Ω)
between the AD9772A digital inputs and driver outputs may be
helpful in reducing overshooting and ringing at the digital
inputs that contribute to data feedthrough.
fDATA = 25MSPS
10
0
0
0.1
0.2
0.3
RATIO (fOUT/fDATA )
CURRENT (mA)
IPLLVDD
15
10
5
0
•
•
ICLKVDD
20
The power dissipation, PD, of the AD9772A is dependent on
several factors, including
•
200
Figure 45. IDVDD vs. Ratio @ DVDD = 3.3 V
POWER DISSIPATION
•
0.5
25
SLEEP MODE OPERATION
The AD9772A has a sleep function that turns off the output current
and reduces the analog supply current to less than 6 mA over the
specified supply range of 3.1 V to 3.5 V. This mode can be activated
by applying a Logic Level 1 to the SLEEP pin. The AD9772A
takes less than 50 ns to power down and then approximately 15 μs
to power up.
0.4
02253-045
ECL/PECL
02253-046
0.1µF
The power supply voltages (AVDD, PLLVDD, CLKVDD,
and DVDD)
The full-scale current output (IOUTFS)
The update rate (fDATA)
The reconstructed digital input waveform
Rev. C | Page 25 of 40
0
50
100
150
fDATA (MSPS)
Figure 46. IPLLVDD and ICLKVDD vs. fDATA
AD9772A
APPLYING THE AD9772A
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if IOUTA and/or IOUTB is connected to an appropriately
sized load resistor, RLOAD, referred to ACOM. This configuration
may be more suitable for a single-supply system requiring a dccoupled, ground-referred output voltage. Alternatively, an amplifier
can be configured as an I-V converter, thus converting IOUTA or
IOUTB into a negative unipolar voltage. This configuration
provides the best dc linearity because IOUTA or IOUTB is
maintained at a virtual ground.
B
DIFFERENTIAL COUPLING USING AN OP AMP
An op amp can also be used to perform a differential-to-singleended conversion as shown in Figure 48. The AD9772A is
configured with two equal load resistors, RLOAD, each of 25 Ω. The
differential voltage developed across IOUTA and IOUTB is converted to
a single-ended signal via the differential op amp configuration. An
optional capacitor can be installed across IOUTA and IOUTB, forming a
real pole in a low-pass filter. The addition of this capacitor also
enhances the distortion performance of the op amp by preventing
the DAC’s high slewing output from overloading the op amp input.
500Ω
AD9772A
225Ω
IOUTA
AD8055
225Ω
IOUTB
COPT
500Ω
B
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used as shown in Figure 47 to perform a
differential-to-single-ended signal conversion. A differentially
coupled transformer output provides the optimum distortion
performance for output signals whose spectral content lies within
the pass band of the transformer. An RF transformer such as the
Mini-Circuits® T1-1T provides excellent rejection of commonmode distortion (that is, even-order harmonics) and noise over a
wide frequency range. It also provides electrical isolation and the
ability to deliver twice the power to the load. Transformers with
different impedance ratios can also be used for impedance
matching purposes. Note that the transformer provides ac coupling
only, and its linearity performance degrades at the low end of its
frequency range due to core saturation.
AD9772A
MINI-CIRCUITS
T1-1T
IOUTA
OPTIONAL
RDIFF
Figure 48. DC Differential Coupling Using an Op Amp
The common-mode rejection of this configuration is typically
determined by the resistor matching. In this circuit, the differential
op amp circuit using the AD8055 is configured to provide some
additional signal gain. The op amp must operate from a dual
supply because its output is approximately ±1.0 V. A high speed
amplifier capable of preserving the differential performance of
the AD9772A while meeting other system-level objectives (such
as cost and power) should be selected. The op amp’s differential
gain, gain-setting resistor values, and full-scale output swing
capabilities should be considered when optimizing this circuit.
The differential circuit shown in Figure 49 provides the
necessary level shifting required in a single-supply system. In
this case, AVDD, the positive analog supply for both the
AD9772A and the op amp, is also used to level-shift the
differential output of the AD9772A to midsupply (that is,
AVDD/2). The AD8057 is a suitable op amp for this application.
RLOAD
500Ω
AD9772A
02253-047
IOUTB
25Ω
25Ω
B
225Ω
IOUTA
225Ω
IOUTB
Figure 47. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages appearing
at IOUTA and IOUTB (that is, VOUTA and VOUTB) swing symmetrically
around ACOM and should be maintained with the specified
output compliance range of the AD9772A. A differential
resistor, RDIFF, can be inserted into applications in which the
output of the transformer is connected to the load, RLOAD, via a
02253-048
The following sections illustrate some typical output
configurations for the AD9772A. Unless otherwise noted, it is
assumed that IOUTFS is set to a nominal 20 mA for optimum
performance. For applications requiring the optimum dynamic
performance, a differential output configuration can consist of
either an RF transformer or a differential op amp configuration.
The transformer configuration provides the optimum high
frequency performance and is recommended for any application
allowing ac coupling. The differential op amp configuration is
suitable for applications requiring dc coupling, a bipolar output,
signal gain, and/or level shifting.
passive reconstruction filter or cable. RDIFF is determined by the
transformer’s impedance ratio and provides the proper source
termination, resulting in a low voltage standing wave ratio
(VSWR). Note that approximately half the signal power is
dissipated across RDIFF.
AD8057
COPT
25Ω
1kΩ
25Ω
AVDD
1kΩ
02253-049
OUTPUT CONFIGURATIONS
Figure 49. Single-Supply DC Differential Coupled Circuit
B
SINGLE-ENDED, UNBUFFERED VOLTAGE OUTPUT
Figure 50 shows the AD9772A configured to provide a unipolar
output range of approximately 0 V to 0.5 V for a doubly terminated 50 Ω cable because the nominal full-scale current, IOUTFS,
Rev. C | Page 26 of 40
AD9772A
of 20 mA flows through the equivalent RLOAD of 25 Ω. In this
case, RLOAD represents the equivalent load resistance seen by
IOUTA. The unused output (IOUTB) should be connected directly to
ACOM. Different values of IOUTFS and RLOAD can be selected as long
as the positive compliance range is adhered to. One additional
consideration in this mode is the integral nonlinearity (INL), as
discussed in the Analog Outputs section of this data sheet. For
optimum INL performance, the single-ended, buffered voltage
output configuration is suggested.
AD9772A
IOUTFS = 20mA
50Ω
50Ω
02253-050
IOUTB
In systems seeking to simultaneously achieve high speed and
high performance, the implementation and construction of the
printed circuit board design is often as important as the circuit
design. Proper RF techniques must be used in device selection,
placement and routing, and supply bypassing and grounding.
Figure 60 to Figure 67 illustrate the recommended printed
circuit board ground, power, and signal plane layouts that are
implemented on the AD9772A evaluation board.
VOUTA = 0V TO 0.5V
IOUTA
Figure 50. 0 V to 0.5 V Unbuffered Voltage Output
SINGLE-ENDED, BUFFERED VOLTAGE OUTPUT
Figure 51 shows a single-ended, buffered output configuration
in which the op amp U1 performs an I-V conversion on the
AD9772A output current. U1 maintains IOUTA (or IOUTB) at virtual
ground, thus minimizing the nonlinear output impedance effect
on the INL performance of the DAC, as discussed in the Analog
Outputs section. Although this single-ended configuration
typically provides the best dc linearity performance, its ac
distortion performance at higher DAC update rates is often
limited by U1’s slewing capabilities. U1 provides a negative
unipolar output voltage, and its full-scale output voltage is
simply the product of RFB and IOUTFS. The full-scale output
should be set within U1’s voltage output swing capabilities
by scaling IOUTFS and/or RFB. An improvement in ac distortion
performance may result in a reduced IOUTFS because the signal
current that U1 will be required to sink is subsequently reduced.
COPT
AD9772A
To meet the first condition, PLLVDD must be driven by the
same power source as CLKVDD, with each supply input
independently decoupled using a 0.1 μF capacitor connected to
its respective ground. To meet the second condition, CLKVDD
can share the same power supply source as DVDD by using the
decoupling network shown in Figure 52 to isolate digital noise
from the sensitive CLKVDD (and PLLVDD) supply. Alternatively,
separate precision voltage regulators can be used to ensure that
the second condition is met.
RFB
200Ω
Proper grounding and decoupling should be a primary
objective in any high speed, high resolution system. The
AD9772A features separate analog and digital supply and
ground pins to optimize the management of analog and digital
ground currents in a system. AVDD, CLKVDD, and PLLVDD
must be powered from a clean analog supply and decoupled to
their respective analog common (that is, ACOM, CLKCOM, and
PLLCOM) as close to the chip as physically possible. Similarly, the
digital supplies (DVDD) should be decoupled to DCOM.
For applications requiring a single 3.3 V supply for the analog,
digital, and phase-lock loop supplies, a clean AVDD and/or
CLKVDD can be generated using the circuit shown in Figure 52.
The circuit consists of a differential LC filter with separate power
supply and return lines. Lower noise can be attained using low ESRtype electrolytic and tantalum capacitors.
TTL/CMOS
LOGIC
CIRCUITS
IOUTFS = 10mA
FERRITE
BEADS
+ 100µF
– ELECTROLYTIC
+ 10µF TO 22µF
– TANTALUM
IOUTA
ACOM
VOUT = –IOUTFS × RFB
200Ω
3.3V
POWER
SUPPLY
Figure 51. Unipolar Buffered Voltage Output
Figure 52. Differential LC Filter for 3.3 V
POWER AND GROUNDING CONSIDERATIONS
The AD9772A contains the following power supply inputs:
AVDD, DVDD, CLKVDD, and PLLVDD. The AD9772A is
specified to operate over a 3.1 V to 3.5 V supply range, thus
accommodating a 3.3 V power supply with up to ±6%
regulation. However, the following two conditions must be
adhered to when selecting power supply sources for AVDD,
DVDD, CLKVDD, and PLLVDD:
•
02253-052
IOUTB
02253-051
U1
•
AVDD
0.1µF
CERAMIC
PLLVDD = CLKVDD = 3.1 V to 3.5 V when the PLL clock
multiplier is enabled (otherwise, PLLVDD = PLLCOM)
DVDD = CLKVDD ± 0.30 V
Maintaining low noise on power supplies and ground is critical
for achieving optimum results from the AD9772A. If properly
implemented, ground planes can perform a host of functions on
high speed circuit boards, such as bypassing and shielding
current transport. In mixed-signal designs, the analog and
digital portions of the board should be distinct from each other,
with the analog ground plane confined to the areas covering the
analog signal traces, and the digital ground plane confined to
areas covering the digital interconnects.
All analog ground pins of the DAC, reference, and other analog
components should be tied directly to the analog ground plane.
The two ground planes should be connected by a path ⅛ to ¼
inch wide underneath or within ½ inch of the DAC to maintain
Rev. C | Page 27 of 40
AD9772A
optimum performance. Care should be taken to ensure that the
ground plane is uninterrupted over crucial signal paths. On the
digital side, this includes the digital input lines running to the
DAC. On the analog side, this includes the DAC output signal,
the reference signal, and the supply feeders.
The use of wide runs or planes in the routing of power lines is
also recommended. This serves the dual role of providing a low
series impedance power supply to the part and allowing some
capacitive decoupling to the appropriate ground plane. It is
essential that care be taken in the layout of signal and power
ground interconnections to avoid inducing extraneous voltage
drops in the signal ground paths. It is recommended that all
connections be short, direct, and as physically close to the
package as possible to minimize the sharing of conduction
paths between different currents. When runs exceed an inch in
length, use of strip line techniques with proper termination
resistors should be considered. The necessity and value of these
resistors depends on the logic family used.
For a more detailed discussion of the implementation and
construction of high speed, mixed-signal printed circuit boards,
refer to the AN-333 Application Note.
Rev. C | Page 28 of 40
AD9772A
APPLICATIONS INFORMATION
–10
MULTICARRIER
Figure 54 shows a spectral plot of the AD9772A operating at
64.54 MSPS, reconstructing eight IS-136-modulated carriers spread
over a 25 MHz band. In this example, the AD9772A exhibits an
SFDR performance of 74 dBc and a carrier-to-noise ratio (CNR) of
73 dB. Figure 55 shows a spectral plot of the AD9772A operating at
52 MSPS, reconstructing four equal GSM-modulated carriers
spread over a 15 MHz band. The SFDR and CNR (in 100 kHz BW)
are measured to be 76 dBc and 83.4 dB, respectively, and have a
channel power of −13.5 dBFS. The test vectors were generated
using the Rohde & Schwarz WinIQSIM software.
–30
AMPLITUDE (dBm)
SPORT
RCF
CIC
FILTER
NCO
QAM
SPORT
RCF
CIC
FILTER
NCO
QAM
PLLLOCK
AD9772A
RCF
CIC
FILTER
NCO
QAM
SPORT
RCF
CIC
FILTER
NCO
QAM
µPORT
JTAG
3.
Although the frequency roll-off of the 2× interpolation
filter provides a maximum reconstruction bandwidth of
0.422 × fDATA, the optimum adjacent image rejection (due to
the interpolation process) can be achieved (that is, > 73 dBc) if
the maximum channel assignment is kept below 0.400 × fDATA.
4.
To simplify the filter requirements (that is, mixer image
and LO rejection) of the subsequent IF stages, it is often
advantageous to offset the frequency band from dc to relax
the transition band requirements of the IF filter.
5.
Oversampling the frequency band often results in improved
SFDR and CNR performance. This implies that the data input
rate to the AD9772A is greater than fPASSBAND/0.4 Hz, where
fPASSBAND is the maximum bandwidth that the AD9772A is
required to reconstruct and place carriers. The improved noise
performance results in a reduction in the TxDAC’s noise
spectral density due to the added process gain realized with
oversampling, and higher oversampling ratios provide greater
flexibility in the frequency planning.
AMPLITUDE (dBm)
–80
30
02253-054
–90
25
25
The AD9772A achieves its optimum noise and distortion
performance when the device is configured for baseband
operation and the differential output and full-scale current,
IOUTFS, are set to approximately 20 mA.
–70
15
20
FREQUENCY (MHz)
20
2.
–60
10
10
15
FREQUENCY (MHz)
To achieve the highest possible CNR, the PLL clock
multiplier should be disabled (that is, PLLVDD to
PLLCOM) and the AD9772A clock input should be driven
with a low jitter, low phase noise clock source at twice the
input data rate. In this case, the divide-by-2 clock
appearing at PLLLOCK should serve as the master clock
for the digital upconverter IC(s), such as the AD6622.
PLLLOCK should be limited to a fanout of 1.
–50
5
5
1.
–30
0
0
Although the above IS-136 and GSM spectral plots are
representative of the AD9772A’s performance for a set of test
conditions, the following recommendations are offered to
maximize the performance and system integration of the
AD9772A into multicarrier applications:
–20
–100
–80
Figure 55. Spectral Plot of AD9772A Reconstructing Four GSM-Modulated
Carriers @ fDATA = 52 MSPS, PLLVDD = 0
Figure 53. Generic Multicarrier Signal Chain Using the AD6622 and AD9772A
–40
–70
–110
OTHER AD6622s FOR
INCREASED CHANNEL
CAPACITY
02253-053
SPORT
–60
–100
CLK+/
CLK–
SUMMATION
–50
–90
CLK
AD6622
–40
02253-055
The AD9772A’s wide dynamic range performance makes it well
suited for next-generation base station applications in which it
reconstructs multiple modulated carriers over a designated frequency band. Cellular multicarrier and multimode radios are
often referred to as software radios because the carrier tuning
and modulation scheme is software programmable and performed
digitally. The AD9772A is the recommended TxDAC® in the
Analog Devices, Inc., SoftCell® chipset, which comprises the
AD6622 (a quadrature digital upconverter IC), the AD6624
(an Rx digital downconverter IC that acts as a companion to the
AD6622), and the AD6644 (a 14-bit, 65 MSPS ADC). Figure 53
shows a generic software radio Tx signal chain using the
AD9772A and AD6622.
–20
Figure 54. Spectral Plot of AD9772A Reconstructing Eight IS-136-Modulated
Carriers @ fDATA = 64.54 MSPS, PLLVDD = 0
Rev. C | Page 29 of 40
AD9772A
Figure 56 shows a spectral plot of the AD9772A reconstructing a
test vector similar to those encountered in WCDMA applications.
However, WCDMA applications prescribe a root raised cosine
filter with an alpha = 0.22, which limits the theoretical ACPR of
the TxDAC to about 70 dB, whereas the test vector represents
white noise that has been band-limited by a brick wall bandpass filter with a pass band for which the maximum ACPR
performance is theoretically 83 dB and the peak-to-rms ratio
is 12.4 dB. As Figure 56 reveals, the AD9772A is capable of
approximately 78 dB ACPR performance when one accounts for
the additive noise/distortion contributed by the Rohde & Schwarz
FSEA30 spectrum analyzer.
Figure 57 shows the actual output spectrum of the AD9772A
reconstructing a 16-QAM test vector with a symbol rate of
5 MSPS. The particular test vector was centered at fDATA/4 with
fDATA = 100 MSPS and fDAC = 400 MHz. For many applications,
the pair of images appearing around fDATA will be more attractive
because this pair has the flattest pass band and highest signal
power. Higher frequency images can also be used, but such
images will have reduced pass-band flatness, dynamic range,
and signal power, thus reducing the CNR and ACP performance.
Figure 58 shows a dual-tone SFDR amplitude sweep at the various
IF images with fDATA = 100 MSPS, fDAC = 400 MHz, and the two
tones centered around fDATA/4. Note that because an IF filter is
assumed to precede the AD9772A, the SFDR was measured
over a 25 MHz window around the images occurring at 75 MHz,
125 MHz, 275 MHz, and 325 MHz.
–20
–30
–40
–60
–70
–80
–30
–40
–90
–50
–100
100
0
–60
–70
300
400
90
–90
75MHz
85
C0
–120
C11
C0
Cu1
C11
CENTER 16.25MHz
600kHz
Cu1
SPAN 6MHz
Figure 56. AD9772A Achieves 78 dB ACPR Performance Reconstructing a
WCDMA-Like Test Vector with fDATA = 65.536 MSPS and PLLVDD = 0
DIRECT IF
As discussed in the Digital Modes of Operation section, the
AD9772A can be configured to transform digital data representing
baseband signals into IF signals appearing at odd multiples of
the input data rate (that is, N × fDATA, where N = 1, 3, and so on).
This is accomplished by configuring the MOD1 and MOD0 digital
inputs high. Note that the maximum DAC update rate of 400 MSPS
limits the data input rate in this mode to 100 MSPS when the
Rev. C | Page 30 of 40
125MHz
80
275MHz
75
70
325MHz
65
60
55
50
–14
–12
–10
–8
–6
AOUT (dBFS)
–4
–2
0
Figure 58. Dual-Tone Windowed SFDR vs. AOUT @ fDATA = 100 MSPS
02253-058
–110
SFDR (IN 25MHz WINDOW) (dBFS)
–100
–130
200
FREQUENCY (MHz)
Figure 57. Spectral Plot of 16-QAM Signal in Direct IF Mode at
fDATA = 100 MSPS
–80
02253-056
AMPLITUDE (dBm)
–50
02253-057
The AD9772A is also well suited for wideband single-carrier
applications, such as WCDMA and multilevel quadrature
amplitude modulation (QAM), whose modulation scheme
requires wide dynamic range from the reconstruction DAC to
achieve the out-of-band spectral mask as well as the in-band
CNR performance. Many of these applications strategically
place the carrier frequency at one quarter of the DAC’s input
data rate (that is, fDATA/4) to simplify the digital modulator
design. Because this constitutes the first fixed IF frequency, the
frequency tuning is accomplished at a later IF stage. To enhance
the modulation accuracy and reduce the shape factor of the
second IF SAW filter, many applications specify that the pass
band of the IF SAW filter be greater than the channel
bandwidth; however, the trade-off is that this requires that the
TxDAC meet the spectral mask requirements of the application
within the extended pass band of the second IF, which may
include two or more adjacent channels.
zero-stuffing operation is enabled (that is, when MOD1 is high).
Applications requiring higher IFs (that is, 140 MHz) using
higher data rates should disable the zero-stuffing operation. In
addition, to minimize the effects of the PLL clock multipliers
phase noise as shown in Figure 31, an external low jitter/phase
noise clock source equal to 4 × fDATA is recommended.
AMPLITUDE (dBm)
BASEBAND SINGLE-CARRIER APPLICATIONS
AD9772A
–20
–30
–40
–50
–60
–70
–80
–90
–110
66
68
70
FREQUENCY (MHz)
72
74
02253-059
For many applications, the data update rate for the DAC (that is,
fDATA) must be a fixed integer multiple of a system reference
clock (for example, GSM − 13 MHz). Furthermore, these
applications prefer to use standard IF frequencies, which offer a
large selection of SAW filter choices with various pass bands
(for example, 70 MHz). In addition, these applications may
benefit from the AD9772A’s direct IF mode capabilities when used
in conjunction with a digital upconverter, such as the AD6622.
Because the AD6622 can digitally synthesize and tune up to four
modulated carriers, it is possible to judiciously tune these carriers
in a region falling within the pass band an IF filter while the
AD9772A is reconstructing a waveform. Figure 59 shows an
example in which four carriers are tuned around 18 MHz with a
digital upconverter operating at 52 MSPS such that when
reconstructed by the AD9772A in the IF mode, these carriers fall
around a 70 MHz IF.
–10
AMPLITUDE (dBm)
Regardless of which image is selected for a given application, the
adjacent images must be sufficiently filtered. In most cases, a SAW
filter providing differential inputs represents the optimum device
for this purpose. For single-ended SAW filters, a balanced-tounbalanced RF transformer is recommended. The high output
impedance of the AD9772A provides a certain amount of
flexibility in selecting the optimum resistive load, RLOAD, as well
as any matching network.
Figure 59. Spectral Plot of Four Carriers at 60 MHz IF with fDATA = 52 MSPS,
PLLVDD = 0
Rev. C | Page 31 of 40
AD9772A
AD9772A EVALUATION BOARD
The AD9772A-EB is an evaluation board for the AD9772A
TxDAC. Careful attention to the layout and circuit design,
along with the prototyping area, allows the user to easily and
effectively evaluate the AD9772A in different modes of operation.
Referring to Figure 60 and Figure 61, the performance of
AD9772A can be evaluated differentially or in a single-ended
fashion using a transformer, differential amplifier, or directly
coupled output. To evaluate the output differentially using the
transformer, remove Jumper JP12 and Jumper JP13 and
monitor the output at J6 (IOUT). To evaluate the output
differentially, remove the transformer (T2) and install jumpers
JP12 and JP13. The output of the amplifier can be evaluated at
J13 (AMPOUT). To evaluate the AD9772A in a single-ended
fashion with a directly coupled output, remove the transformer
and Jumper JP12 and Jumper JP13, and install Resistor R16 or
Resistor R17 with 0 Ω.
The digital data to the AD9772A comes across a ribbon cable
that interfaces to a 40-pin IDC connector. Proper termination
or voltage scaling can be accomplished by installing the RN2
and/or RN3 SIP resistor networks. The 22 Ω DIP resistor
network, RN1, must be installed and helps reduce the digital
data edge rates. A single-ended clock input can be supplied via
the ribbon cable by installing JP8, or, more preferably, via the
SMA connector, J3 (CLOCK). If the clock is supplied by J3, the
AD9772A can be configured for a differential clock interface by
installing Jumper JP1 and configuring JP2, JP3, and JP9 in the
DF position. To configure the AD9772A clock input for a
single-ended clock interface, remove JP1 and configure JP2,
JP3, and JP9 in the SE position.
The AD9772A PLL clock multiplier can be disabled by configuring Jumper JP5 in the L position. In this case, the user must
supply a clock input at twice (2×) the data rate via J3 (CLOCK).
The 1× clock is available on the SMA connector J1 (PLLLOCK),
and should be used to trigger a pattern generator directly or via
a programmable pulse generator. Note that PLLLOCK is capable
of providing a 0 V to 0.85 V output into a 50 Ω load. To enable
the PLL clock multiplier, JP5 must be configured for the
H position. In this case, the clock can be supplied via the ribbon
cable (that is, JP8 installed) or J3 (CLOCK). The divide-by-N
ratio can be set by configuring JP6 (DIV0) and JP7 (DIV1).
The AD9772A can be configured for baseband or direct IF
mode operation by configuring Jumper JP11 (MOD0) and
Jumper JP10 (MOD1). For baseband operation, JP10 and JP11
should be configured in the L position. For direct IF operation,
JP10 and JP11 should be configured in the H position. For direct
IF operation without zero-stuffing, JP11 should be configured in
the H position while JP10 should be configured in the low position.
The AD9772A voltage reference can be enabled or disabled via
JP4. To enable the reference, configure JP4 in the internal position.
A voltage of approximately 1.2 V will appear at the TP6 (REFIO)
test point. To disable the internal reference, configure JP4 in the
external position and drive TP6 with an external voltage reference.
Lastly, the AD9772A can be placed in the sleep mode by driving
the TP11 test point with a logic level high input signal.
Rev. C | Page 32 of 40
AD9772A
SCHEMATICS
P1 1
4 P1
P1 3
6 P1
P1 5
8 P1
10 P1
P1 7
P1 9
12 P1
P1 11
14 P1
P1 13
16 P1
P1 15
IN13
DB13
2
IN12
2
15
DB12
3
IN11
3
14
DB11
4
IN10
4
13
DB10
5
IN9
5
12
DB9
6
IN8
6
11
DB8
7
IN7
7
10
DB7
8
IN6
8
9
DB6
9
MSB
RN3
VALUE
1
MSB
IN13
IN12
IN11
IN10
IN9
IN8
IN7
IN6
10
18 P1
20 P1
P1 17
P1 19
22 P1
P1 21
24 P1
P1 23
26 P1
28 P1
P1 25
P1 27
30 P1
P1 29
32 P1
P1 31
34 P1
P1 33
36 P1
P1 35
38 P1
P1 37
40 P1
P1 39
1
16
DB5
2
IN4
2
15
DB4
3
IN3
3
14
DB3
4
IN2
4
13
DB2
5
IN1
5
12
DB1
6
IN0
6
11
DB0
7
7
10
CLOCK
8
8
9
RESET
9
LSB
INCLOCK
IN4
IN3
IN2
IN1
IN0
LSB
INCLOCK
INRESET
6
7
8
9
2
3
4
5
6
7
8
9
10
INRESET
R15
500Ω
+VS
R4
500Ω
IA
IB
5
1
IN5
10
JP12
AMP-A
JP13
AMP-B
4
RN6
VALUE
1
IN5
3
10
RN5
VALUE
RN4
VALUE
2
C16
100pF
2
R12
500Ω
R13
50Ω
3
R11
50Ω
R14
500Ω
–IN
7
AD8055
+V
6
OUT
U2
+IN
–V
4
AMPOUT
1
J13
2
C18
0.1µF
–VS
C17
0.1µF
J7
J8
1 DVDD_IN
TP22
DVDD
C13
10µF
10V
1 DGND
BLK
TP19
RED
FBEAD
2
L1
1
RED
TP20
TP23
BLK
J9
J10
1 AVDD_IN
RED
FBEAD
2
L2
1
TP24
AVDD
C14
10µF
10V
1 AGND
TP25
BLK
J11
J12
RED
FBEAD
2
L3
1 CLKVDD_IN 1
TP26
CLKVDD
C15
10µF
10V
1 CLKGND
TP27
c
BLK
Figure 60. Drafting Schematic of Evaluation Board
Rev. C | Page 33 of 40
02253-060
2 P1
RN2
VALUE
1
RN1
VALUE
1
16
AD9772A
RED
TP16
BLK
TP17
WHT
TP5
WHT
TP6
AVDD
C5
0.1µF
DB8
DB7
DB6
DB5
DB4
REFLO
REFIO
3
34
4
33
5
32
U1
PLLVDD
29
9
28
DIV0
10
27
DIV1
11
26
12
25
30
c
DB2
DB1
(LSB) DB0
DB3
C11
0.1µF
PLLLOCK
3
B
B
H
JP11 2
A L
H
JP10 2
A L
1
1
J1
2
B
2A
TP10
WHT
1
SE B
DF
CLKVDD
JP8
EDGE
2
SE B
1
4
2
2
DF A
J6
C2
10pF
R7
50Ω
R3
1kΩ
JP3
T1
1
S
C19
0.1µF
c
6
2
4
3
1
c
1
P
IOUT
c
2
R1
50Ω
6
IB
JP1
DF
JP2
2A
R2
1kΩ
CLOCK
S
WHT
TP12 CLOCK
J3
3
T2
P
R9
OPT
JP7
A
DVDD
TP2
WHT
3
B
2
3
IA
3
1
1
R16
VAL
R8
50Ω
JP6
2A
TP28
WHT
NOTE:
LOCATE ALL DECOUPLING CAPACITORS (C5 TO C12) AS CLOSE AS POSSIBLE TO DUT,
PREFERABLY UNDER DUT ON THE BOTTOM SIGNAL LAYER.
C3
10pF
3
B
c
MOD1
DGND
JP5
1
TP7 RED
c
TP1
WHT
3
3
TP4
WHT
C12
1µF
MOD0
DVDD
TP3
WHT
CLKVDD
CLKVDD
1
c
C10
0.1µF
RESET
13 14 15 16 17 18 19 20 21 22 23 24
c
C9
1µF
31
AD9772A
8
C1
VAL
R5
VAL
LPF
CLK–
CLK+
7
NOTE:
SHIELD AROUND R5, C1
CONNECTED TO PLLVDD
TP11
SLEEP WHT
35
6
JP4
INT REF 1
1
R17
VAL
3
DF B
SE
JP9
2A
1
c
Figure 61. Drafting Schematic of Evaluation Board (Continued)
Rev. C | Page 34 of 40
02253-061
DB10
DB9
B
2A
REFLO
36
PIN 1
IDENTIFIER
2
DB12
DB11
FSADJ
48 47 46 45 44 43 42 41 40 39 38 37
1
(MSB) DB13
R10
1.91kΩ
R6
50Ω
C8
0.1µF
TP15
BLK
OUTB
DVDD
C7
0.1µF
C4
0.1µF
IOUTA
AVDD
RED
TP14
EXT REF 3
C6
1µF
AD9772A
02253-062
EVALUATION BOARD LAYOUT
02253-063
Figure 62. Silkscreen Layer—Top
Figure 63. Component-Side PCB Layout (Layer 1)
Rev. C | Page 35 of 40
02253-064
AD9772A
02253-065
Figure 64. Ground Plane PCB Layout (Layer 2)
Figure 65. Power Plane PCB Layout (Layer 3)
Rev. C | Page 36 of 40
02253-066
AD9772A
02253-067
Figure 66. Solder-Side PCB Layout (Layer 4)
Figure 67. Silkscreen Layer—Bottom
Rev. C | Page 37 of 40
AD9772A
OUTLINE DIMENSIONS
9.20
9.00 SQ
8.80
1.60
MAX
37
48
36
1
PIN 1
0.15
0.05
7.20
7.00 SQ
6.80
TOP VIEW
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
SEATING
PLANE
VIEW A
(PINS DOWN)
25
12
13
VIEW A
0.50
BSC
LEAD PITCH
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
24
0.27
0.22
0.17
051706-A
0.75
0.60
0.45
Figure 68. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9772AAST
AD9772AASTZ 1
AD9772AASTRL
AD9772AASTZRL1
AD9772A-EB
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
Evaluation Board
Z = RoHS Compliant Part.
Rev. C | Page 38 of 40
Package Option
ST-48
ST-48
ST-48
ST-48
AD9772A
NOTES
Rev. C | Page 39 of 40
AD9772A
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02253-0-2/08(C)
Rev. C | Page 40 of 40