EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Evaluating the ADN4651/ADN4652 5 kV RMS, 600 Mbps LVDS Isolator (SOIC_W) FEATURES GENERAL DESCRIPTION Isolated ground planes (logic side and bus side) Convenient connections through SMA terminals 3.3 V or 2.5 V power on Side 1 (VIN1/VDD1) and Side 2 (VIN2/VDD2) Ground on Side 1 (GND1) and Side 2 (GND2) LVDS input signals: DIN1+, DIN1−, DIN2+, DIN2− LVDS output signals: DOUT1+, DOUT1−, DOUT2+, DOUT2− Jumper-selectable supply power of 3.3 V or 2.5 V Termination resistors on all LVDS drivers/receivers The EVAL-ADN4651EB1Z and EVAL-ADN4652EB1Z allow quick and easy evaluation of the ADN4651/ADN4652 low-voltage differential signalling (LVDS) isolator without the need for external components. The ADN4651/ADN4652 employ Analog Devices, Inc., iCoupler® technology to combine a 2-channel isolator with an LVDS receiver and driver into a single, 20-lead wide body SOIC package. They are capable of running at data rates of up to 600 Mbps with very low jitter. EVALUATION KIT CONTENTS EVAL-ADN4651EB1Z or EVAL-ADN4652EB1Z evaluation board DOCUMENTS NEEDED ADN4650/ADN4651/ADN4652 data sheet EQUIPMENT NEEDED Signal generator Oscilloscope PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. The evaluation board has separate ground and power planes for each side of the isolator. This separation enables the evaluation of the ADN4651/ADN4652 with galvanic isolation between both sides of the device. Jumper-selectable power supplies at 3.3 V or 2.5 V are required on each side of the ADN4651/ADN4652. Using an on-chip LDO, 2.5 V can be provided from an external 3.3 V power supply. Complete information about the ADN4651/ADN4652 is available in the ADN4650/ADN4651/ADN4652 data sheet, which should be consulted in conjunction with this user guide when using the evaluation boards. Rev. A | Page 1 of 13 UG-900 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Setting Up the Evaluation Board .................................................4 Evaluation Kit Contents ................................................................... 1 Radiated Emissions Test Results (EN 55022) ................................6 Documents Needed .......................................................................... 1 Evaluation Board Schematic and Artwork.....................................8 Equipment Needed ........................................................................... 1 Ordering Information .................................................................... 12 General Description ......................................................................... 1 Bill of Materials ........................................................................... 12 Revision History ............................................................................... 2 Related Links ............................................................................... 12 ADN4651 and ADN4652 Evaluation Board Photographs.......... 3 Evaluation Board Configuration .................................................... 4 REVISION HISTORY 5/16—Rev. 0 to Rev. A Added the EVAL-ADN4652EB1Z and ADN4652 ............ Universal Changes to Documents Needed Section ....................................... 1 Added Figure 2; Renumbered Sequentially .................................. 2 Changes to Setting Up the Evaluation Board Section ................. 3 Changes to Figure 5 Caption, Table 2, and Table 3 ...................... 4 Changes to Figure 6 Caption and Radiated Emissions Test Results (EN 55022) Section ..................................................... 6 Added Figure 11 and Figure 12....................................................... 8 Added Table 6; Renumbered Sequentially .................................. 12 Changes to Related Link Section .................................................. 12 12/15—Revision 0: Initial Version Rev. A | Page 2 of 13 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide UG-900 13761-001 EVALUATION BOARD PHOTOGRAPHS 13761-100 Figure 1. EVAL-ADN4651EB1Z Evaluation Board Figure 2. EVAL-ADN4652EB1Z Evaluation Board Rev. A | Page 3 of 13 UG-900 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide EVALUATION BOARD CONFIGURATION SETTING UP THE EVALUATION BOARD An example operation of the EVAL-ADN4651EB1Z is shown in Figure 5 (signal generator and oscilloscope connections are reversed for EVAL-ADN4652EB1Z, per Table 2 and Table 3). SMA connectors expose all LVDS inputs and outputs for the EVAL-ADN4651EB1Z, but are reversed for the EVALADN4652EB1Z (see Table 2 and Table 3). Connect a signal generator to the board using the J1 and J2 connectors and set up a 300 MHz square wave clock with an amplitude of 350 mV and an offset of 1.2 V. Connect the oscilloscope directly to the J5 and J6 connectors to perform timing measurements including propagation delay and skew. Precision measurements, for example, jitter, using a differential probe requires attaching the probe at the R7 or R3 resistors and potentially cutting the traces to the connectors to minimize reflections. Figure 3. DOUT1− and DOUT1+ with a 300 MHz Clock, Single-Ended and Differential 13761-003 When using a 3.3 V power supply, VIN1 and VDD1 (Pin 1 and Pin 3 on the ADN4651/ADN4652) are bypassed to GND1 using 1 µF capacitors. VIN2 and VDD2 (Pin 20 and Pin 18 on the ADN4651/ ADN4652) are bypassed to GND2 using 1 µF capacitors. When using a 2.5 V power supply, VIN1 or VIN2 is connected directly to VDD1 or VDD2 by shorting Jumpers P4 or P7, respectively. Both VDD1 pins are also bypassed to GND1 with 0.1 µF capacitors. Both VDD2 pins are also bypassed to GND2 with 0.1 µF capacitors. 13761-002 On the EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z, power supplies are configured using Jumpers P4 and P7 (see Table 1) and connected to the J9 and J10 SMA connectors (see Table 2 and Table 3). A 3.3 V power supply can be applied to Side 1 and/or Side 2 of the ADN4651/ADN4652 by removing Jumpers P4 (Side 1) and P7 (Side 2). If a 2.5 V supply is connected to the board, the relevant jumper must be inserted (P4 for Side 1 and P7 for Side 2). At 300 MHz with a load resistance of 100 Ω, the maximum operating current from each power supply is 90 mA. Figure 4. DOUT2− and DOUT2+ with a 300 MHz Clock, Single-Ended and Differential A plot of the oscilloscope connected via the J5 and J6 connectors is shown in Figure 3. Channel 3 (green) and Channel 4 (purple) show the J5 and J6 connectors separately (single-ended) with the differential signal (orange). Operation of the second isolated LVDS channel is shown in Figure 4. In contrast to Figure 5, the oscilloscope now connects via the J3 and J4 connectors and the signal generator connects to the J7 and J8 connectors. Channel 3 (green) and Channel 4 (purple) show the J3 and J4 connectors separately (single-ended) with the differential signal (orange). Rev. A | Page 4 of 13 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide 2.5V OR 3.3V SUPPLY J9 J1 VIN1 VDD1 P4 R1 2.5V OR 3.3V SUPPLY GND1 GND2 J2 R2 R4 J3 U1 R3 VIN2 VDD2 J5 P7 R7 J6 R8 R5 J7 R6 J8 J4 GND1 J22 GND2 EVAL-ADN4651EB1Z R12 J24 OSCILLOSCOPE J10 R11 R10 J21 R9 13761-004 SIGNAL GENERATOR UG-900 J23 Figure 5. Basic LVDS Isolator Evaluation Board Operation for the EVAL-ADN4651EB1Z; Scope and Signal Generator Reversed for the EVAL-ADN4652EB1Z Table 1. Jumper Configuration Jumper P4 P7 Position Open Closed Open Closed Description 3.3 V power supply connected to Connector J9 for VIN1 2.5 V power supply connected to Connector J9, VIN1 shorted to VDD1 3.3 V power supply connected to Connector J9 for VIN2 2.5 V power supply connected to Connector J9, VIN2 shorted to VDD2 Table 2. Side 1 Connector Descriptions EVAL-ADN4651EB1Z Connector J9 J1 J2 J3 J4 J22 J24 EVAL-ADN4652EB1Z Connector J9 J3 J4 J1 J2 J22 J24 Description Power supply, 3.3 V (Jumper P4 open) or 2.5 V (Jumper P4 closed) DIN1+, noninverted LVDS input for Channel 1 DIN1−, inverted LVDS input for Channel 1 DOUT2+, noninverted LVDS output for Channel 2 DOUT2−, inverted LVDS output for Channel 2 Connects to Connector J21 (test trace for calibration) Connects to Connector J23 (test trace for calibration) Table 3. Side 2 Connector Descriptions EVAL-ADN4651EB1Z Connector J10 J5 J6 J7 J8 J21 J23 EVAL-ADN4652EB1Z Connector J10 J7 J8 J5 J6 J21 J23 Description Power supply, 3.3 V (Jumper P7 open) or 2.5 V (Jumper P7 closed) DOUT1+, noninverted LVDS output for Channel 1 DOUT1−, inverted LVDS output for Channel 1 DIN2+, noninverted LVDS input for Channel 2 DIN2−, inverted LVDS input for Channel 2 Connects to Connector J22 (test trace for calibration) Connects to Connector J24 (test trace for calibration) Rev. A | Page 5 of 13 UG-900 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide RADIATED EMISSIONS TEST RESULTS (EN 55022) 2 × AA BATTERY 3V TO 3.15V J9 VIN1 SIGNAL GENERATOR VIN2 GND1 GND2 VDD1 J1 2 × AA BATTERY 3V TO 3.15V P4 VDD2 J5 P7 R7 R1 10m COAX CABLE ×2 J10 J6 J2 R2 R4 J3 R8 R5 U1 R3 J7 R6 J8 J4 GND1 GND2 EVAL-ADN4651EB1Z R12 R11 J24 NOTES 1. SIGNAL GENERATOR OUTSIDE TEST CHAMBER 2. INPUT SIGNAL: |VID| = 300mV, VIC = 1.1V, 600MBPS PRBS7 OR 300MHz CLOCK R10 J21 R9 J23 13761-105 J22 Figure 6. Test Setup for EN 55022 Radiated Emissions Testing for the EVAL-ADN4651EB1Z; Scope and Signal Generator Reversed for the EVAL-ADN4652EB1Z Radiated emissions testing is performed with the EVALADN4651EB1Z and EVAL-ADN4652EB1Z at an independent external test facility. Evaluating the EVAL-ADN4651EB1Z and EVAL-ADN4652EB1Z to the EN 55022 standard is undertaken in a 10 m radiated emissions test chamber, using the test setup shown in Figure 6. The setup comprises a battery-powered EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z connected to a signal generator located outside the chamber via coax cables. As specified by the EN 55022 standard, both horizontal and vertical peak scans are undertaken with any visible emissions peaks investigated using quasi-peak detector measurement. For each frequency measured using a quasi-peak detector, the unit under test rotates through 360 degrees to find the worst case angle. The receiving antenna then elevates from 1 m to 4 m in height to find the worst case elevation. The worst case quasi-peak measurements are compared to the EN 55022 Class B and Class A limits. The test results for EVAL-ADN4651EB1Z and EVALADN4652EB1Z are shown in Table 4 and a classification report for both evaluation boards is available on request (please contact Analog Devices or the distributor for support). Radiated emissions are measured across 30 MHz to 1 GHz and from 1 GHz to 3 GHz. With a 600 Mbps PRBS7 input, the EVAL-ADN4651EB1Z/EVALADN4652EB1Z passes the EN 55022 Class B limits. Plots for horizontal and vertical peak radiated emissions below 1 GHz are shown in Figure 7 and Figure 8, respectively, for the EVALADN4651EB1Z; see the classification report for the EVALADN4652EB1Z plots. With a 300 MHz clock input, the EVAL-ADN4651EB1Z/EVALADN4652EB1Z passes the EN 55022 Class A limits. To pass the Class B limits when isolating high frequency clocks, reduce the printed circuit board (PCB) clearance from the 8 mm implemented on the EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z to, for example, 2 mm. Table 4. EN 55022 Radiated Emissions Classification Test Condition 600 Mbps PRBS 300 MHz Clock Rev. A | Page 6 of 13 Result Passes EN 55022 Class B Passes EN 55022 Class A EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide UG-900 80 70 60 (dBµV/m) 50 40 30 20 0 30 100 1000 FREQUENCY (MHz) 13761-106 10 Figure 7. EVAL-ADN4651EB1Z Radiated Emissions (Horizontal, Peak, 30 MHz to 1 GHz) with 600 Mbps PRBS7 Input 80 70 60 (dBµV/m) 50 40 30 20 0 30 100 FREQUENCY (MHz) 1000 13761-107 10 Figure 8. EVAL-ADN4651EB1Z Radiated Emissions (Vertical, Peak, 30 MHz to 1 GHz) with 600 Mbps PRBS7 Input Rev. A | Page 7 of 13 UG-900 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide EVALUATION BOARD SCHEMATIC AND ARTWORK J21 R9 DNP R10 DNP R11 R12 DNP DNP J24 P4 P7 1 2 J22 J23 1 2 TP6 TP5 AGND3 VDD1 TP1 VDD2 TP40 DNP C8 C6 1UF C7 100NF C5 100NF P C10 N C12 C20 DNP C19 1UF C4 100NF C3 DNP C2 1UF C1 100NF C11 DNP N 10UF P J10 DNP DECOUPLING C9 C18 1UF AGND2 AGND1 100 R1 AGND1 DNP R2 J1 J5 AGND1 R7 100 AGND2 J6 AGND2 J4 AGND1 20PIN SOICWB AGND2 J7 R6 DNP R5 AGND1 100 AGND1 DNP TP3 R3 AGND2 TP41 5001 1 TP42 5001 1 AGND2 J3 J8 AGND1 AGND2 13761-006 Figure 9. EVAL-ADN4651EB1Z Schematic Figure 10. EVAL-ADN4651EB1Z Silkscreen Rev. A | Page 8 of 13 13761-005 TP2 R8 J2 20 VIN2 19 18 17 16 15 14 13 12 11 DNP U1 VIN1 1 2 VDD1 3 4 5 6 7 8 9 10 100 R4 C17 DNP J9 VIN2 10UF VIN1 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide J21 J23 R9 DNP R10 DNP R11 R12 DNP DNP J24 P4 P7 1 2 J22 UG-900 1 2 TP6 TP5 AGND3 VDD1 TP1 VDD2 TP40 C8 DNP C6 1UF C7 100NF 100NF C5 P C10 N C12 C20 DNP C19 1UF C4 100NF C3 DNP C2 1UF C1 100NF C11 DNP N 10UF P J10 DNP DECOUPLING C9 C18 1UF AGND2 AGND1 DNI R1 AGND1 100 R2 J1 J5 AGND1 R7 DNI AGND2 J6 AGND2 J4 AGND1 20PIN SOICWB AGND2 J7 R6 100 R5 AGND1 DNI AGND1 100 TP3 R3 AGND2 TP41 5001 1 TP42 5001 1 AGND2 J3 J8 AGND1 AGND2 13761-102 Figure 11. EVAL-ADN4652EB1Z Schematic Figure 12. EVAL-ADN4652EB1Z Silkscreen Rev. A | Page 9 of 13 13761-101 TP2 R8 J2 20 VIN2 19 18 17 16 15 14 13 12 11 100 U1 VIN1 1 2 VDD1 3 4 5 6 7 8 9 10 DNI R4 C17 DNP J9 VIN2 10UF VIN1 13761-007 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide Figure 13. EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z Component Side 13761-008 UG-900 Figure 14. EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z Inner Layer 2, Ground Rev. A | Page 10 of 13 UG-900 13761-009 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide 13761-010 Figure 15. EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z Inner Layer 3, Power Figure 16. EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z Solder Side Rev. A | Page 11 of 13 UG-900 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide ORDERING INFORMATION BILL OF MATERIALS Table 5. Bill of Materials for the EVAL-ADN4651EB1Z Qty. 4 2 4 2 2 10 4 2 8 4 2 4 2 1 Reference Designator C1, C4, C5, C7 C2, C6 C3, C8, C11, C12, C17, C20 C9, C10 C18, C19 J1 to J10 J21 to J24 P4, P7 R1, R4, R6, R8 to R12 R2, R3, R5, R7 TP1/VDD1, TP40/VDD2 TP2, TP3, TP41, TP42 TP5/VIN1, TP6/VIN2 U1 Description Capacitors, 100 nF, 0402 Capacitors, 1 µF, 0603 Capacitors, 0402 Capacitors, tantalum, 10 µF, Case C Capacitors, 1 µF, 0402 Connectors, SMA, edge Connectors, SMA, edge 2-pin, header and jumper Resistors, 0402 Resistors, 100 Ω, 0402 Test points, yellow Test points, black Test points, red ADN4651 5 kV rms, 600 Mbps, LVDS isolator Manufacturer Multicomp Multicomp Not fitted AVX Multicomp Johnson Not fitted TE Connectivity Not fitted Multicomp Vero Vero Vero Analog Devices Part Number MC0402X104K100CT MC0603X105K100CT Not applicable TAJC106K016RNJ MC0402X105K6R3CT 142-0701-801 Not applicable 826926-2 and 3M/969102-0000-DA) Not applicable MCMR04X1000FTL 20-313140 20-2137 20-313137 ADN4651BRWZ Manufacturer Multicomp Multicomp Not fitted AVX Multicomp Johnson Not fitted TE Connectivity Not fitted Multicomp Vero Vero Vero Analog Devices Part Number MC0402X104K100CT MC0603X105K100CT Not applicable TAJC106K016RNJ MC0402X105K6R3CT 142-0701-801 Not applicable 826926-2 and 3M/969102-0000-DA) Not applicable MCMR04X1000FTL 20-313140 20-2137 20-313137 ADN4652BRWZ Table 6. Bill of Materials for the EVAL-ADN4652EB1Z Qty. 4 2 4 2 2 10 4 2 8 4 2 4 2 1 Reference Designator C1, C4, C5, C7 C2, C6 C3, C8, C11, C12, C17, C20 C9, C10 C18, C19 J1 to J10 J21 to J24 P4, P7 R2, R3, R5, R7, R9 to R12 R1, R4, R6, R8 TP1/VDD1, TP40/VDD2 TP2, TP3, TP41, TP42 TP5/VIN1, TP6/VIN2 U1 Description Capacitors, 100 nF, 0402 Capacitors, 1 µF, 0603 Capacitors, 0402 Capacitors, tantalum, 10 µF, Case C Capacitors, 1 µF, 0402 Connectors, SMA, edge Connectors, SMA, edge 2-pin, header and jumper Resistors, 0402 Resistors, 100 Ω, 0402 Test points, yellow Test points, black Test points, red ADN4652 5 kV rms, 600 Mbps, LVDS isolator RELATED LINKS Resource ADN4651 ADN4652 Description Product page, ADN4651, 5 kV rms, 600 Mbps, dual-channel isolated LVDS Product page, ADN4652, 5 kV rms, 600 Mbps, dual-channel isolated LVDS Rev. A | Page 12 of 13 EVAL-ADN4651EB1Z/EVAL-ADN4652EB1Z User Guide UG-900 NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2015–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG13761-0-5/16(A) Rev. A | Page 13 of 13