DC1595A - Demo Manual

DEMO MANUAL DC1595A
LT3799
Offline Isolated Flyback Led
Controller with PFC
DESCRIPTION
Demonstration circuit 1595A is an off-line isolated flyback
converter featuring LT3799. The demo board is designed
to drive a 20V nominal LED string at 1A from an input
voltage range of 90VAC to 270VAC. It is also designed to
comply with IEC 61000-3-2 Class C harmonics standard
and EN55015B conducted EMI standard.
The LT3799 controls an isolated flyback converter in
boundary mode, suitable for LED applications requiring
4W to over 100W of LED power. Its novel current sensing
scheme delivers a well regulated output current to the
secondary side without using an opto-coupler. Its unique
bleeder circuit makes the LED driver compatible with
PERFORMANCE SUMMARY
TRIAC dimmers without additional components. Openand shorted-LED protection ensures long term reliability.
The LT3799 is available in a low profile, thermally enhanced
16-lead MSOP package.
The LT3799 datasheet gives a complete description of the
part, operation and application information. The datasheet
must be read in conjunction with this quick start guide for
demo circuit 1595A.
Design files for this circuit board are available at
http://www.linear.com/demo
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
(TA = 25°C)
PARAMETER
CONDITIONS
VALUE
Input Range
Line Frequency, 50Hz/60Hz
90VAC to 270VAC
Output Current IOUT
VIN = 120VAC
1A
Maximum Output Voltage
25V
Minimum Output Voltage
16V
dc1595afb
1
DEMO MANUAL DC1595A
QUICK START PROCEDURE
IMPORTANT NOTE TO CUSTOMERS:
HIGH VOLTAGES ARE PRESENTED ON THE DEMO CIRCUIT,
AND CAN LEAD TO LETHAL INJURIES TO HUMAN BODY.
ONLY QUALIFIED PERSONEL SHOULD OPERATE IT. IT IS
STRONGLY RECOMMENDED TO USE SAFETY GLASSES
AND AN ISOLATION TRANSFORMER.
NOTE. IMPROPER COMPONENTS REPLACEMENT ON THE
DEMO CIRCUIT CAN CAUSE PERFORMANCE DETERIORATIONS, CIRCUIT MALFUNCTION, PROPERTY DAMAGE,
AND EVEN LIFE-THREATHENING INJURIES. CONTACT
LINEAR TECHNOLOGY APPLICATIONS ENGINEERS FOR
PROPER COMPONENT REPLACEMENT.
Demonstration circuit 1595A is easy to set up to evaluate the performance of the LT3799. Refer to Figure 1 for
proper measurement equipment setup and complete the
following procedure:
1. Connect a 1A LED string between LED+ and LED– terminals.
2. With power off, connect the input power supply to Line
(L) Input and Neutral (N) Input.
3. Turn on the power at the input.
NOTE. Make sure that the input voltage does not exceed
the maximum input voltage (270VAC).
4. Check for the proper output current.
Once the proper output currents are established, adjust
the input voltage and/or the load and observe the output
current regulation, efficiency, power factor and other
parameters.
Figure 1. Proper Measurement Equipment Setup
dc1595afb
2
DEMO MANUAL DC1595A
QUICK START PROCEDURE
100
EFFICIENCY (%)
95
90
85
80
75
70
90 110 130 150 170 190 210 230 250 270
VIN (AC-RMS)
Figure 2. Efficiency vs VIN
1.2
1.0
ILED (A)
0.8
220V APPLICATION
0.6
120V APPLICATION
0.4
0.2
0
0
30
120
90
60
150
TRIAC ANGLE (DEGREES)
180
Figure 3. LED Current vs TRIAC Angle
1.00
0.99
POWER FACTOR ( )
0.98
0.97
0.96
0.95
0.94
0.93
0.92
0.91
0.90
90 110 130 150 170 190 210 230 250 270
VIN (VAC)
Figure 4. Power Factor vs Input Voltage
dc1595afb
3
DEMO MANUAL DC1595A
PARTS LIST
ITEM
QTY
REFERENCE
PART DESCRIPTION
MANUFACTURER/PART NUMBER
Required Circuit Components
1
1
B1
RECTIFIER, BRIDGE 600V 0.8A
DIODES INC. HD06-T
2
1
C1
CAP, 0.068μF 20% 305VAC MKP
VISHAY BFC2 339 20683
3
1
C2
CAP, 0.1μF 10% 450V
RUBYCON 450MMK104J
4
1
C3
CAP, 10μF 20% 50V ALUM
RUBYCON 50YXJ10M 5X11
5
1
C4
CAP, 0.22μF 20% 450V FILM
RUBYCON 450MMK 224K
6
1
C6
CAP, 0603 0.015μF 10% 50V X7R
AVX 06035C153KAT2A
7
1
C7
CAP, 0603 0.1μF 10% 50V X7R
AVX 06035C104KAT2A
8
1
C8
CAP, 0805 4.7μF 20% 16V X5R
AVX 0805YD475MAT2A
9
2
C10, C11
CAP, 560μF 20% 35V ELEC
RUBYCON 35ZLJ560M 10X20
10
1
C20
CAP, 2.2nF 10% Y5B TYPE "Y1"
VISHAY 440LD22-R
11
1
C21
CAP, 0603 4.7pF ±0.1pF 50V NP0
AVX 06035A4R7CAT2A
12
1
D1
DIODE, FAST SWITCHING
DIODES INC. US1J-13-F
13
2
D2, D8
DIODE, FAST SWITCHING
DIODES INC. BAV20W-7-F
14
1
D5
DIODE, 150V , 1A, SBR
DIODES INC. SBR1U150SA
15
1
F1
FUSE, 1A
BUSSMAN SS-5H-1A
16
1
L1
IND, 33mH
WURTH ELECTRONIK 7448640418
17
1
L2
IND, 750μH
WURTH ELECTRONIK 750311431
18
1
Q1
XSTR, MOSFET, N-CHANNEL 650V
FAIRCHILD SEMI FDPF15N65
19
2
R1, R2
RES, 1206 100kΩ 1% 1/4W
VISHAY CRCW1206100KFKEA
20
2
R3, R18
RES, 0603 100kΩ 1% 1/10W
VISHAY CRCW0603100KFKEA
21
1
R4
RES, 0603 4.99kΩ 1% 1/10W
VISHAY CRCW06034K99FKEA
22
2
R5, R25
RES, 0603 20Ω 1% 1/10W
VISHAY CRCW060320R0FKEA
23
1
R7
RES, 0603 2kΩ 1% 1/10W
VISHAY CRCW06032K00FKEA
24
1
R8
RES, 1206 0.05Ω 1% 1/4W
VENKEL LCR1206-R050GT
25
1
R9
RES, 1206 4.02kΩ 1% 1/4W
VISHAY CRCW12064K02FKEA
26
2
R10, R11
RES, 1206 499kΩ 1% 1/4W
VISHAY CRCW1206499KFKEA
27
1
R12
RES, 0603 3.48kΩ 1% 1/10W
VISHAY CRCW06033K48FKEA
28
1
R19
RES, 0603 40.2kΩ 1% 1/10W
VISHAY CRCW060340K2FKEA
29
1
R20
RES, 0603 16.9kΩ 1% 1/10W
VISHAY CRCW060316K9FKEA
30
1
R21
RES, 0603 0kΩ JUMPER
VISHAY CRCW06030000Z0EA
31
1
R30
RES, 200Ω 5% 1W METAL OXIDE
KOA MOS1CT52R201J
32
1
T1
XFMR, FLYBACK
COILCRAFT JA4429-AL
33
1
U1
IC, TRAIC DMMABLE OFFLINE LED DRIVER
LINEAR TECH. LT3799EMSE
34
1
V1
VARISTOR, 320V RMS 13.5MM RADIAL
SEI CV1320K10T
35
1
Z2
DIODE, TRANSIENT VOLTAGE SUPPRESSOR 170V
DIODES INC. SMBJ170A
36
1
Z3
DIODE, ZENER, 33V
DIODES INC.SMAZ33-13-F
Additional Demo Board Circuit Components
1
0
R22
RES, 0603 OPTION
OPTION
4
E1, E2, E4, E5
TURRET
MILL MAX MILL-MAX 2501-2-00-80-00-00-07-0
Hardware
1
dc1595afb
4
N
E2
V1
320VAC
3
2
1A
4
1
90 - 270VAC
50/60Hz
33mH
L1
0.068uF
X CAP
C1
L2
-
FAULT
2
750uH
3
4
F1
FAULT
+
HD06
B1
1
C2
1%
100k
R18
R20
16.9k
1%
R2
100k
1%
R11
499k
1%
R12
3.48k
1%
R1
100k
1%
R19
40.2k
1%
0.1uF
400V
R10
499k
1%
R30
200
0.22uF
C4
R22
OPT
R21
0
BAV20W
D8
R5
20
1%
5
1
2
3
4
12
16
C3
10uF
50V
2
C7
FAULT
CTRL1
CTRL2
CTRL3
VREF
NC
VINSENSE
0.1uF
1
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
C21
COMP+
COMP-
INTVCC
SENSE
GATE
FB
1%
2k
R7
4.7pF
C20
THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND
SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
ENG. :(,*
PCB DES. :(,*0 ,
Z3
+
560uF
35V
C11
DATE:
IC NO.
LED-
SHEET
LT3799EMSE
DEMO CIRCUIT 1595A
OF
2
REV
1630 McCarthy Blvd.
Milpitas, CA 95035
Phone: (408)432-1900
Fax: (408)434-0507
LTC Confidential-For Customer Use Only
560uF
35V
C10
R9
4.02k
1%
E5
LED+
WEI G.
E4
DATE
02/03/11
APPROVED
OFFLINE ISOLATED FLYBACK LED
CONTROLLER WITH PFC
N/A
SIZE
+
TECHNOLOGY
CMZ5937B
33V
TITLE: SCHEMATIC
Y1
D5
SBR1U150SA
PRODUCTION
2
REVISION HISTORY
DESCRIPTION
REV
2200pF
APPROVALS
R8
50m
FDPF15N65
Q1
2
CONTRACT NO.
CMR1U-06M
D1
SMBJ170A
Z2
6
4
1
7
4:1
T1
3
CUSTOMER NOTICE
LT3799EMSE
0.015uF
50V
C6
16V
R25
20 1%
4.7uF
C8
INTVCC
U1
7
8
13
15
14
9
R4
4.99k
1%
1%
100k
R3
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;
HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO
VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL
APPLICATION. COMPONENT SUBSTITUTION AND PRINTED
CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT
PERFORMANCE OR RELIABILITY. CONTACT LINEAR
TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.
BAV20W
D2
+
E1
6
1
2
L
11
VIN
CT
10
DCM
GND
17
1
2
ECO
DEMO MANUAL DC1595A
SCHEMATIC DIAGRAM
dc1595afb
5
DEMO MANUAL DC1595A
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
dc1595afb
6
Linear Technology Corporation
LT 1111 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2011