PHILIPS 74AUP1Z125GW

74AUP1Z125
Low-power X-tal driver with enable and internal resistor
Rev. 01 — 3 August 2006
Product data sheet
1. General description
The 74AUP1Z125 is a high-performance, low-power, low-voltage, Si-gate CMOS device,
superior to most advanced CMOS compatible TTL families.
When not in use the EN input can be driven HIGH, pulling up the X1 input and putting the
device in a low power disable mode. Schmitt-trigger action at the EN input makes the
circuit tolerant to slower input rise and fall times across the entire VCC range from 0.8 V to
3.6 V.
This device ensures a very low static and dynamic power consumption across the entire
VCC range from 0.8 V to 3.6 V.
This device is fully specified for partial Power-down applications using IOFF at output Y.
The IOFF circuitry disables the output Y, preventing the damaging backflow current through
the device when it is powered down.
The 74AUP1Z125 combines the functions of the 74AUP1GU04 and 74AUP1G125 to
provide a device optimized for use in crystal oscillator applications.
The integration of the two devices into the 74AUP1Z125 produces the benefits of a
compact footprint, lower power dissipation and stable operation over a wide range of
frequency and temperature.
2. Features
■ Wide supply voltage range from 0.8 V to 3.6 V
■ High noise immunity
■ ESD protection:
◆ HBM JESD22-A114-C Class 3A. Exceeds 5000 V
◆ MM JESD22-A115-A exceeds 200 V
◆ CDM JESD22-C101-C exceeds 1000 V
■ Low static power consumption; ICC = 0.9 µA (maximum)
■ Latch-up performance exceeds 100 mA per JESD 78 Class II
■ Inputs accept voltages up to 3.6 V
■ Low noise overshoot and undershoot < 10 % of VCC
■ IOFF circuitry provides partial Power-down mode operation at output Y
■ Multiple package options
■ Specified from −40 °C to +85 °C and −40 °C to +125 °C
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
3. Ordering information
Table 1.
Ordering information
Type number
Package
Temperature range Name
Description
Version
74AUP1Z125GW
−40 °C to +125 °C
SC-88
plastic surface-mounted package; 6 leads
SOT363
74AUP1Z125GM
−40 °C to +125 °C
XSON6
plastic extremely thin small outline package; no leads; SOT886
6 terminals; body 1 × 1.45 × 0.5 mm
74AUP1Z125GF
−40 °C to +125 °C
XSON6
plastic extremely thin small outline package; no leads; SOT891
6 terminals; body 1 × 1 × 0.5 mm
4. Marking
Table 2.
Marking
Type number
Marking code
74AUP1Z125GW
55
74AUP1Z125GM
55
74AUP1Z125GF
55
5. Functional diagram
VCC
RPU
X1
6
3
RFB
EN
4
Y
X2
1
001aaf141
Fig 1. Logic symbol
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
2 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
6. Pinning information
6.1 Pinning
74AUP1Z125
74AUP1Z125
EN
1
6
EN
1
6
Y
GND
2
5
VCC
Y
GND
2
5
VCC
X1
3
4
X2
X1
3
4
X2
74AUP1Z125
EN
1
6
Y
GND
2
5
VCC
X1
3
4
X2
001aaf143
001aaf144
Transparent top view
Transparent top view
001aaf142
Fig 2. Pin configuration SOT363
(SC-88)
Fig 3. Pin configuration SOT886
(XSON6)
Fig 4. Pin configuration SOT891
(XSON6)
6.2 Pin description
Table 3.
Pin description
Symbol
Pin
Description
EN
1
enable input (active LOW)
GND
2
ground (0 V)
X1
3
data input
X2
4
unbuffered output
VCC
5
supply voltage
Y
6
data output
7. Functional description
Table 4.
Function table[1]
Input
Output
EN
X1
X2
Y
L
L
H
H
L
H
L
L
H
L
H
Z
H
H
L
Z
[1]
H = HIGH voltage level;
L = LOW voltage level;
Z = high-impedance OFF-state.
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
3 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
VCC
supply voltage
IIK
input clamping current
VI
input voltage
IOK
output clamping current
Conditions
VI < 0 V
[1]
VO < 0 V
[1]
Min
Max
Unit
−0.5
+4.6
V
-
−50
mA
−0.5
+4.6
V
-
−50
mA
−0.5
VCC + 0.5
V
VO
output voltage
IO
output current
-
±20
mA
ICC
supply current
-
+50
mA
IGND
ground current
-
−50
mA
Tstg
storage temperature
−65
+150
°C
-
250
mW
total power dissipation
Ptot
VO = 0 V to VCC
Tamb = −40 °C to +125 °C
[2]
[1]
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2]
For SC-88 packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K.
For XSON6 packages: above 45 °C the value of Ptot derates linearly with 2.4 mW/K.
9. Recommended operating conditions
Table 6.
Recommended operating conditions
Symbol
Parameter
Conditions
VCC
supply voltage
VI
input voltage
0
3.6
V
VO
output voltage
0
VCC
V
Tamb
ambient temperature
−40
+125
°C
∆t/∆V
input transition rise and fall rate
0
200
ns/V
VCC = 0.8 V to 3.6 V
74AUP1Z125_1
Product data sheet
Min
Max
Unit
0.8
3.6
V
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
4 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
10. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min
Typ
Max
Unit
0.75 × VCC -
-
V
VCC = 0.8 V
0.70 × VCC -
-
V
VCC = 0.9 V to 1.95 V
0.65 × VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
-
-
0.25 × VCC V
VCC = 0.8 V
-
-
0.30 × VCC V
VCC = 0.9 V to 1.95 V
-
-
0.35 × VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.1
-
-
V
Tamb = 25 °C
VIH
HIGH-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
VIL
LOW-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
VOH
HIGH-level output voltage
Y output; VI = VIH or VIL
IO = −1.1 mA; VCC = 1.1 V
0.75 × VCC -
-
V
IO = −1.7 mA; VCC = 1.4 V
1.11
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.32
-
-
V
IO = −2.3 mA; VCC = 2.3 V
2.05
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.9
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.72
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.6
-
-
V
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.1
-
-
V
IO = −1.1 mA; VCC = 1.1 V
0.75 × VCC -
-
V
IO = −1.7 mA; VCC = 1.4 V
1.11
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.32
-
-
V
IO = −2.3 mA; VCC = 2.3 V
2.05
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.9
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.72
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.6
-
-
V
X2 output; VI = GND or VCC
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
5 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
VOL
Y output; VI = VIH or VIL
LOW-level output voltage
Min
Typ
Max
Unit
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 × VCC
V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.31
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.31
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.31
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.44
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.31
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.44
V
X2 output; VI = GND or VCC
II
input leakage current
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 × VCC
V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.31
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.31
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.31
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.44
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.31
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.44
V
-
-
±10
µA
-
-
±0.1
µA
-
-
−15
µA
VI = GND or VCC; EN = GND;
VCC = 0.8 V to 3.6 V
-
-
±7.5
µA
-
-
±0.1
µA
X1 input
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V;
VCC = 0 V to 3.6 V
Ipu
pull-up current
X1 input; EN = VCC
VI = GND; VCC = 0.8 V to 3.6 V
Ifbck
feedback current
X1 input
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V; EN = VCC
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
[1]
-
-
±0.2
µA
∆IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
[1]
-
-
±0.2
µA
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
-
-
10
µA
∆ICC
additional supply current
EN input
-
-
40
µA
VI = VCC − 0.6 V; IO = 0 A;
VCC = 3.3 V
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
6 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
CI
X1 input
input capacitance
Min
Typ
Max
Unit
-
1.5
-
pF
-
0.8
-
pF
-
1.8
-
pF
-
1.7
-
pF
0.75 × VCC -
-
V
VCC = 0.8 V
0.70 × VCC -
-
V
VCC = 0.9 V to 1.95 V
0.65 × VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
-
-
0.25 × VCC V
VCC = 0.8 V
-
-
0.30 × VCC V
VCC = 0.9 V to 1.95 V
-
-
0.35 × VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
VCC = 0 V to 3.6 V;
VI = GND or VCC
EN input
VCC = 0 V to 3.6 V;
VI = GND or VCC
CO
output capacitance
X2 output
VO = GND; VCC = 0 V
Y output
VO = GND; VCC = 0 V
Tamb = −40 °C to +85 °C
VIH
HIGH-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
VIL
LOW-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
7 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
VOH
Y output; VI = VIH or VIL
HIGH-level output voltage
Min
Typ
Max
Unit
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.1
-
-
V
IO = −1.1 mA; VCC = 1.1 V
0.7 × VCC
-
-
V
IO = −1.7 mA; VCC = 1.4 V
1.03
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.30
-
-
V
IO = −2.3 mA; VCC = 2.3 V
1.97
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.85
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.67
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.55
-
-
V
X2 output; VI = GND or VCC
VOL
LOW-level output voltage
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.1
-
-
V
IO = −1.1 mA; VCC = 1.1 V
0.7 × VCC
-
-
V
IO = −1.7 mA; VCC = 1.4 V
1.03
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.30
-
-
V
IO = −2.3 mA; VCC = 2.3 V
1.97
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.85
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.67
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.55
-
-
V
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 × VCC
V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.37
V
Y output; VI = VIH or VIL
IO = 1.9 mA; VCC = 1.65 V
-
-
0.35
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.33
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.45
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.33
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.45
V
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.1
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.3 × VCC
V
X2 output; VI = GND or VCC
IO = 1.7 mA; VCC = 1.4 V
-
-
0.37
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.35
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.33
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.45
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.33
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.45
V
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
8 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
II
X1 input
input leakage current
Min
Typ
Max
Unit
-
-
±15
µA
-
-
±0.5
µA
-
-
−15
µA
VI = GND or VCC; EN = GND;
VCC = 0.8 V to 3.6 V
-
-
±7.5
µA
-
-
±0.5
µA
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V;
VCC = 0 V to 3.6 V
Ipu
pull-up current
X1 input; EN = VCC
Ifbck
feedback current
X1 input
VI = GND; VCC = 0.8 V to 3.6 V
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V; EN = VCC
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
[1]
-
-
±0.5
µA
[1]
-
-
±0.6
µA
-
-
0.9
µA
-
-
50
µA
0.75 × VCC -
-
V
VCC = 0.8 V
0.75 × VCC -
-
V
VCC = 0.9 V to 1.95 V
0.70 × VCC -
-
V
VCC = 2.3 V to 2.7 V
1.6
-
-
V
VCC = 3.0 V to 3.6 V
2.0
-
-
V
-
-
0.25 × VCC V
VCC = 0.8 V
-
-
0.25 × VCC V
VCC = 0.9 V to 1.95 V
-
-
0.30 × VCC V
VCC = 2.3 V to 2.7 V
-
-
0.7
V
VCC = 3.0 V to 3.6 V
-
-
0.9
V
∆IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
∆ICC
additional supply current
EN input
VI = VCC − 0.6 V; IO = 0 A;
VCC = 3.3 V
Tamb = −40 °C to +125 °C
VIH
HIGH-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
VIL
LOW-level input voltage
X1 input
VCC = 0.8 V to 3.6 V
EN input
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
9 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
VOH
Y output; VI = VIH or VIL
HIGH-level output voltage
Min
Typ
Max
Unit
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.11 -
-
V
IO = −1.1 mA; VCC = 1.1 V
0.6 × VCC
-
-
V
IO = −1.7 mA; VCC = 1.4 V
0.93
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.17
-
-
V
IO = −2.3 mA; VCC = 2.3 V
1.77
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.67
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.40
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.30
-
-
V
X2 output; VI = GND or VCC
VOL
LOW-level output voltage
IO = −20 µA; VCC = 0.8 V to 3.6 V
VCC − 0.11 -
-
V
IO = −1.1 mA; VCC = 1.1 V
0.6 × VCC
-
-
V
IO = −1.7 mA; VCC = 1.4 V
0.93
-
-
V
IO = −1.9 mA; VCC = 1.65 V
1.17
-
-
V
IO = −2.3 mA; VCC = 2.3 V
1.77
-
-
V
IO = −3.1 mA; VCC = 2.3 V
1.67
-
-
V
IO = −2.7 mA; VCC = 3.0 V
2.40
-
-
V
IO = −4.0 mA; VCC = 3.0 V
2.30
-
-
V
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.11
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.33 × VCC V
IO = 1.7 mA; VCC = 1.4 V
-
-
0.41
Y output; VI = VIH or VIL
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.39
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.36
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.50
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.36
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.50
V
IO = 20 µA; VCC = 0.8 V to 3.6 V
-
-
0.11
V
IO = 1.1 mA; VCC = 1.1 V
-
-
0.33 × VCC V
X2 output; VI = GND or VCC
IO = 1.7 mA; VCC = 1.4 V
-
-
0.41
V
IO = 1.9 mA; VCC = 1.65 V
-
-
0.39
V
IO = 2.3 mA; VCC = 2.3 V
-
-
0.36
V
IO = 3.1 mA; VCC = 2.3 V
-
-
0.50
V
IO = 2.7 mA; VCC = 3.0 V
-
-
0.36
V
IO = 4.0 mA; VCC = 3.0 V
-
-
0.50
V
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
10 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 7.
Static characteristics …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
II
X1 input
input leakage current
Min
Typ
Max
Unit
-
-
±20
µA
-
-
±0.75
µA
-
-
−15
µA
VI = GND or VCC; EN = GND;
VCC = 0.8 V to 3.6 V
-
-
±7.5
µA
-
-
±0.75
µA
VI = EN = VCC; VCC = 0 V to 3.6 V
EN input
VI = GND to 3.6 V;
VCC = 0 V to 3.6 V
Ipu
pull-up current
X1 input; EN = VCC
Ifbck
feedback current
X1 input
VI = GND; VCC = 0.8 V to 3.6 V
IOZ
OFF-state output current
VI = VIH or VIL; VO = 0 V to 3.6 V;
VCC = 0 V to 3.6 V; EN = VCC
IOFF
power-off leakage current
VI or VO = 0 V to 3.6 V; VCC = 0 V
[1]
-
-
±0.75
µA
[1]
-
-
±0.75
µA
-
-
1.4
µA
-
-
75
µA
∆IOFF
additional power-off
leakage current
VI or VO = 0 V to 3.6 V;
VCC = 0 V to 0.2 V
ICC
supply current
VI = GND or VCC; IO = 0 A;
VCC = 0.8 V to 3.6 V
∆ICC
additional supply current
EN input
VI = VCC − 0.6 V; IO = 0 A;
VCC = 3.3 V
[1]
Only for output Y.
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
11 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
11. Dynamic characteristics
Table 8.
Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7.
Symbol Parameter
25 °C
Conditions
−40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85 °C)
Max
(125 °C)
-
6.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
0.9
2.3
4.4
0.9
4.8
5.3
ns
VCC = 1.4 V to 1.6 V
0.7
1.7
3.1
0.6
3.4
3.8
ns
VCC = 1.65 V to 1.95 V
0.5
1.4
2.6
0.5
2.9
3.2
ns
VCC = 2.3 V to 2.7 V
0.4
1.1
2.0
0.4
2.3
2.6
ns
0.3
1.0
1.8
0.3
2.1
2.4
ns
-
18.5
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.8
5.9
12.5
3.2
14.8
16.3
ns
VCC = 1.4 V to 1.6 V
2.2
4.2
7.7
2.6
9.1
10.1
ns
VCC = 1.65 V to 1.95 V
1.9
3.5
6.2
2.2
7.8
8.6
ns
VCC = 2.3 V to 2.7 V
1.6
2.9
4.8
1.9
6.2
6.9
ns
1.4
2.6
4.1
1.7
4.7
5.2
ns
-
31.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.1
6.1
13.8
2.9
16.3
18.0
ns
VCC = 1.4 V to 1.6 V
2.5
4.3
8.2
2.3
9.7
10.7
ns
CL = 5 pF
tpd
propagation delay X1 to X2; see Figure 5
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Figure 5
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
ten
enable time
EN to Y; see Figure 6
[3]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
2.1
3.6
6.5
2.0
7.6
8.4
ns
VCC = 2.3 V to 2.7 V
1.8
2.9
4.8
1.7
5.8
6.4
ns
1.7
2.6
4.1
1.7
4.7
5.2
ns
VCC = 3.0 V to 3.6 V
tdis
disable time
EN to Y; see Figure 6
VCC = 0.8 V
[4]
-
11.1
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.5
4.5
9.0
2.9
9.4
10.4
ns
VCC = 1.4 V to 1.6 V
2.0
3.3
6.4
2.3
6.7
7.4
ns
VCC = 1.65 V to 1.95 V
1.9
3.2
6.0
2.0
6.4
7.1
ns
VCC = 2.3 V to 2.7 V
1.4
2.3
4.4
1.7
4.7
5.2
ns
VCC = 3.0 V to 3.6 V
1.7
2.6
4.4
1.7
4.9
5.4
ns
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
12 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7.
Symbol Parameter
25 °C
Conditions
−40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85 °C)
Max
(125 °C)
-
9.6
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
1.2
3.1
6.1
1.2
6.8
7.5
ns
VCC = 1.4 V to 1.6 V
1.0
2.3
4.0
0.9
4.6
5.1
ns
VCC = 1.65 V to 1.95 V
0.8
1.9
3.3
0.7
3.8
4.2
ns
VCC = 2.3 V to 2.7 V
0.6
1.5
2.7
0.6
3.1
3.5
ns
0.5
1.3
2.4
0.5
2.7
3.0
ns
-
21.4
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.2
6.7
14.3
3.6
16.2
17.9
ns
VCC = 1.4 V to 1.6 V
2.1
4.9
8.9
3.0
10.1
11.2
ns
CL = 10 pF
tpd
propagation delay X1 to X2; see Figure 5
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Figure 5
[2]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
1.9
4.1
6.9
2.6
8.0
8.8
ns
VCC = 2.3 V to 2.7 V
2.1
3.4
5.4
2.3
6.6
7.3
ns
1.8
3.1
4.8
3.0
5.6
6.2
ns
VCC = 3.0 V to 3.6 V
ten
enable time
EN to Y; see Figure 6
[3]
VCC = 0.8 V
tdis
disable time
-
34.4
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.6
6.9
15.5
3.4
16.0
17.6
ns
VCC = 1.4 V to 1.6 V
2.3
5.0
9.3
2.2
9.6
10.6
ns
VCC = 1.65 V to 1.95 V
2.0
4.2
7.2
1.9
7.9
8.7
ns
VCC = 2.3 V to 2.7 V
1.8
3.4
5.5
1.7
6.4
7.1
ns
VCC = 3.0 V to 3.6 V
1.7
3.2
4.9
1.7
5.5
6.1
ns
-
13.0
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.4
5.7
10.4
3.4
10.8
11.9
ns
VCC = 1.4 V to 1.6 V
2.1
4.2
7.6
2.2
8.0
8.8
ns
VCC = 1.65 V to 1.95 V
2.2
4.3
7.3
1.9
7.6
8.4
ns
VCC = 2.3 V to 2.7 V
1.6
3.1
5.3
1.7
5.5
6.1
ns
VCC = 3.0 V to 3.6 V
2.1
3.8
6.0
1.7
6.5
7.2
ns
EN to Y; see Figure 6
VCC = 0.8 V
[4]
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
13 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7.
Symbol Parameter
25 °C
Conditions
−40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85 °C)
Max
(125 °C)
-
13.0
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
1.6
3.8
7.9
1.4
8.8
9.7
ns
VCC = 1.4 V to 1.6 V
1.3
2.8
4.9
1.1
5.7
6.3
ns
VCC = 1.65 V to 1.95 V
1.0
2.3
4.0
0.9
4.7
5.2
ns
VCC = 2.3 V to 2.7 V
0.8
1.9
3.2
0.8
3.7
4.1
ns
0.7
1.6
2.9
0.7
3.3
3.7
ns
-
24.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
3.6
7.5
16.1
4.0
17.6
19.4
ns
VCC = 1.4 V to 1.6 V
3.0
5.4
9.7
3.3
10.6
11.7
ns
CL = 15 pF
tpd
propagation delay X1 to X2; see Figure 5
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Figure 5
[2]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
2.2
4.6
7.7
2.9
9.0
9.9
ns
VCC = 2.3 V to 2.7 V
2.0
3.9
6.1
2.6
7.3
8.1
ns
2.0
3.6
5.4
2.3
5.9
6.5
ns
VCC = 3.0 V to 3.6 V
ten
enable time
EN to Y; see Figure 6
[3]
VCC = 0.8 V
tdis
disable time
-
37.5
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.0
7.7
17.2
3.7
17.5
19.3
ns
VCC = 1.4 V to 1.6 V
3.0
5.5
10.0
2.5
10.2
11.3
ns
VCC = 1.65 V to 1.95 V
2.3
4.7
7.9
2.1
9.2
10.2
ns
VCC = 2.3 V to 2.7 V
2.0
3.9
6.2
2.0
7.4
8.2
ns
VCC = 3.0 V to 3.6 V
2.0
3.6
5.5
1.9
6.0
6.6
ns
-
14.8
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.3
6.8
11.2
3.7
12.4
13.7
ns
VCC = 1.4 V to 1.6 V
3.0
5.1
8.1
2.5
8.9
9.8
ns
VCC = 1.65 V to 1.95 V
3.0
5.4
8.0
2.1
9.3
10.3
ns
VCC = 2.3 V to 2.7 V
2.1
3.9
6.1
2.0
7.3
8.1
ns
VCC = 3.0 V to 3.6 V
2.9
5.1
7.2
1.9
7.9
8.7
ns
EN to Y; see Figure 6
VCC = 0.8 V
[4]
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
14 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7.
Symbol Parameter
25 °C
Conditions
−40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85 °C)
Max
(125 °C)
-
23.2
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
2.4
6.0
13.1
2.2
14.8
16.3
ns
VCC = 1.4 V to 1.6 V
2.0
4.2
7.6
1.8
9.0
9.9
ns
VCC = 1.65 V to 1.95 V
1.7
3.6
6.1
1.5
7.2
8.0
ns
VCC = 2.3 V to 2.7 V
1.4
2.9
4.8
1.3
5.7
6.3
ns
1.2
2.5
4.3
1.1
5.1
5.7
ns
-
32.6
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
4.8
9.6
21.0
5.0
21.7
23.9
ns
VCC = 1.4 V to 1.6 V
4.0
6.9
12.4
4.3
13.5
14.9
ns
CL = 30 pF
tpd
propagation delay X1 to X2; see Figure 5
[2]
VCC = 0.8 V
VCC = 3.0 V to 3.6 V
X1 to Y; see Figure 5
[2]
VCC = 0.8 V
VCC = 1.65 V to 1.95 V
2.9
5.9
9.8
3.8
10.7
11.8
ns
VCC = 2.3 V to 2.7 V
2.7
5.0
7.5
3.3
8.2
9.1
ns
2.7
4.7
6.8
3.1
7.7
8.5
ns
VCC = 3.0 V to 3.6 V
ten
enable time
EN to Y; see Figure 6
[3]
VCC = 0.8 V
tdis
disable time
-
47.1
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
5.2
9.9
21.0
4.8
21.7
23.9
ns
VCC = 1.4 V to 1.6 V
4.0
7.1
12.4
3.1
13.5
14.9
ns
VCC = 1.65 V to 1.95 V
3.0
6.0
9.9
2.8
10.7
11.8
ns
VCC = 2.3 V to 2.7 V
2.7
5.0
7.7
2.6
8.1
9.0
ns
VCC = 3.0 V to 3.6 V
2.7
4.8
6.8
2.6
7.7
8.5
ns
-
20.3
-
-
-
-
ns
VCC = 1.1 V to 1.3 V
6.0
10.2
15.3
4.8
16.5
18.2
ns
VCC = 1.4 V to 1.6 V
4.4
7.8
11.2
3.1
12.3
13.6
ns
VCC = 1.65 V to 1.95 V
5.1
8.8
12.5
2.8
13.3
14.7
ns
VCC = 2.3 V to 2.7 V
3.6
6.3
8.6
2.6
9.5
10.5
ns
VCC = 3.0 V to 3.6 V
5.2
8.8
11.5
2.6
13.0
14.3
ns
EN to Y; see Figure 6
VCC = 0.8 V
[4]
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
15 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 8.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 7.
Symbol Parameter
25 °C
Conditions
−40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85 °C)
Max
(125 °C)
VCC = 0.8 V
-
5.8
-
-
-
-
pF
VCC = 1.1 V to 1.3 V
-
6.0
-
-
-
-
pF
VCC = 1.4 V to 1.6 V
-
6.2
-
-
-
-
pF
VCC = 1.65 V to 1.95 V
-
6.8
-
-
-
-
pF
VCC = 2.3 V to 2.7 V
-
9.7
-
-
-
-
pF
VCC = 3.0 V to 3.6 V
-
12.6
-
-
-
-
pF
CL = 5 pF, 10 pF, 15 pF and 30 pF
power dissipation
capacitance
CPD
[5][6]
f = 1 MHz; EN = GND;
VI = GND to VCC
[1]
All typical values are measured at nominal VCC.
[2]
tpd is the same as tPLH and tPHL.
[3]
ten is the same as tPZH and tPZL.
[4]
tdis is the same as tPHZ and tPLZ.
[5]
CPD is used to determine the dynamic power dissipation (PD in µW).
PD = CPD × VCC2 × fi × N + Σ(CL × VCC2 × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
Σ(CL × VCC2 × fo) = sum of the outputs.
[6]
Feedback current is included in CPD.
12. Waveforms
VI
X1 input
VM
VM
GND
t PHL
t PLH
VOH
X2, Y output
VM
VM
VOL
001aaf145
Measurement points are given in Table 9.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 5. The input (X1) to output (X2, Y) propagation delays
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
16 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
Table 9.
Measurement points
Supply voltage
Output
Input
VCC
VM
VM
VI
tr = tf
0.8 V to 3.6 V
0.5 × VCC
0.5 × VCC
VCC
≤ 3.0 ns
VI
VM
EN input
GND
tPLZ
tPZL
VCC
Y output
LOW-to-OFF
OFF-to-LOW
VM
VX
VOL
tPHZ
VOH
tPZH
VY
Y output
HIGH-to-OFF
OFF-to-HIGH
VM
GND
outputs
enabled
outputs
disabled
outputs
enabled
001aaf146
Measurement points are given in Table 10.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 6. Enable and disable times
Table 10.
Measurement points
Supply voltage
Input
Output
VCC
VM
VM
VX
VY
0.8 V to 1.6 V
0.5 × VCC
0.5 × VCC
VOL + 0.1 V
VOH − 0.1 V
1.65 V to 2.7 V
0.5 × VCC
0.5 × VCC
VOL + 0.15 V
VOH − 0.15 V
3.0 V to 3.6 V
0.5 × VCC
0.5 × VCC
VOL + 0.3 V
VOH − 0.3 V
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
17 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
VCC
VEXT
5 kΩ
VI
PULSE
GENERATOR
VO
DUT
RT
CL
RL
001aac521
Test data is given in Table 11.
Definitions for test circuit:
RL = Load resistance.
CL = Load capacitance including jig and probe capacitance.
RT = Termination resistance should be equal to the output impedance Zo of the pulse generator.
VEXT = External voltage for measuring switching times.
Fig 7. Load circuitry for switching times
Table 11.
Test data
Supply voltage
Load
VEXT
RL[1]
VCC
CL
0.8 V to 3.6 V
5 pF, 10 pF, 15 pF and 30 pF 5 kΩ or 1 MΩ
[1]
tPLH, tPHL
tPZH, tPHZ
tPZL, tPLZ
open
GND
2 × VCC
For measuring enable and disable times RL = 5 kΩ, for measuring propagation delays, setup and hold times and pulse width RL = 1 MΩ.
001aad074
30
gfs
(mA/V)
20
1 MΩ
VCC
10
0.47 µF
input
100 µF
output
Vi
Io
0
0
Fig 8. Test set-up for measuring forward
transconductance
2
3
4
Fig 9. Typical forward transconductance as a function
of supply voltage
74AUP1Z125_1
Product data sheet
1
VCC (V)
001aad595
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
18 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
13. Application information
Crystal controlled oscillator circuits are widely used in clock pulse generators because of
their excellent frequency stability and wide operating frequency range. The use of the
74AUP1Z125 provides the additional advantages of low power dissipation, stable
operation over a wide range of frequency and temperature and a very small footprint. This
application information describes crystal characteristics, design and testing of crystal
oscillator circuits based on the 74AUP1Z125.
13.1 Crystal characteristics
Figure 10 is the equivalent circuit of a quartz crystal.
The reactive and resistive component of the impedance of the crystal alone and the
crystal with a series and a parallel capacitance is shown in Figure 11.
C1
C0
L1
R1
mnb102
Fig 10. Equivalent circuit of a crystal
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
19 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
C1
+
resistance
(a)
R1
L1
C0
0
fr
R1
fa
f
∞
reactance
−
+
C1
resistance
RL
(b)
L1
C0
0
fL
fa
f
R1
∞
reactance
CL
−
+
Rp
C1
resistance
(c) CL
C0
L1
0
fr
fL
fa
f
R1
∞
reactance
−
mnb104
(1) (a) = resonance
(2) (b) = anti-resonance
(3) (c) = load resonance
Fig 11. Average ICC as a function of VCC
13.1.1 Design
Figure 12 shows the recommended way to connect a crystal to the 74AUP1Z125. This
circuit is basically a Pierce oscillator circuit in which the crystal is operating at its
fundamental frequency and is tuned by the parallel load capacitance of C1 and C2. C1 and
C2 are in series with the crystal. They should be approximately equal. R1 is the
drive-limiting resistor and is set to approximately the same value as the reactance of C1 at
the crystal frequency (R1 = XC1). This will result in an input to the crystal of 50 % of the
rail-to-rail output of X2. This keeps the drive level into the crystal within drive specifications
(the designer should verify this). Overdriving the crystal can cause damage.
The internal 1 MΩ resistor provides negative feedback and sets a bias point of the inverter
near mid-supply, operating the 74AUP1GU04 in the high gain linear region.
To calculate the values of C1 and C2, the designer can use the formula:
C1 × C2
C L = ------------------- + C s
C1 + C2
CL is the load capacitance as specified by the crystal manufacturer, Cs is the stray
capacitance of the circuit (for the 74AUP1Z125 this is equal to an input capacitance
of 5 pF).
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
20 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
74AUP1GU04
portion
74AUP1G125
portion
system
load
Y
X1
1 MΩ
X2
Xtal
Csys
C2
Rsys
C1
001aaf147
Fig 12. Crystal oscillator configuration
13.1.2 Testing
After the calculations are performed for a particular crystal, the oscillator circuit should be
tested. The following simple checks will verify the prototype design of a crystal controlled
oscillator circuit. Perform them after laying out the board:
• Test the oscillator over worst-case conditions (lowest supply voltage, worst-case
crystal and highest operating temperature). Adding series and parallel resistors can
simulate a worse case crystal.
• Insure that the circuit does not oscillate without the crystal.
• Check the frequency stability over a supply range greater than that which is likely to
occur during normal operation.
• Check that the start-up time is within system requirements.
As the 74AUP1Z125 isolates the system loading, once the design is optimized, the single
layout may work in multiple applications for any given crystal.
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
21 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
14. Package outline
Plastic surface-mounted package; 6 leads
SOT363
D
E
B
y
X
A
HE
6
5
v M A
4
Q
pin 1
index
A
A1
1
2
e1
3
bp
c
Lp
w M B
e
detail X
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A1
max
bp
c
D
E
e
e1
HE
Lp
Q
v
w
y
mm
1.1
0.8
0.1
0.30
0.20
0.25
0.10
2.2
1.8
1.35
1.15
1.3
0.65
2.2
2.0
0.45
0.15
0.25
0.15
0.2
0.2
0.1
OUTLINE
VERSION
REFERENCES
IEC
SOT363
JEDEC
JEITA
SC-88
EUROPEAN
PROJECTION
ISSUE DATE
04-11-08
06-03-16
Fig 13. Package outline SOT363 (SC-88)
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
22 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm
SOT886
b
1
2
3
4×
(2)
L
L1
e
6
5
e1
4
e1
6×
A
(2)
A1
D
E
terminal 1
index area
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A (1)
max
A1
max
b
D
E
e
e1
L
L1
mm
0.5
0.04
0.25
0.17
1.5
1.4
1.05
0.95
0.6
0.5
0.35
0.27
0.40
0.32
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
OUTLINE
VERSION
SOT886
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
04-07-15
04-07-22
MO-252
Fig 14. Package outline SOT886 (XSON6)
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
23 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm
1
SOT891
b
3
2
L
L1
e
6
5
4
e1
e1
A
A1
D
E
terminal 1
index area
0
1
2 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max
A1
max
b
D
E
e
e1
L
L1
mm
0.5
0.04
0.20
0.12
1.05
0.95
1.05
0.95
0.55
0.35
0.35
0.27
0.40
0.32
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
05-03-11
05-04-06
SOT891
Fig 15. Package outline SOT891 (XSON6)
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
24 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
15. Abbreviations
Table 12.
Abbreviations
Acronym
Description
CDM
Charged Device Model
CMOS
Complementary Metal Oxide Semiconductor
DUT
Device Under Test
ESD
ElectroStatic Discharge
HBM
Human Body Model
MM
Machine Model
TTL
Transistor-Transistor Logic
16. Revision history
Table 13.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
74AUP1Z125_1
20060803
Product data sheet
-
-
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
25 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
17. Legal information
17.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.semiconductors.philips.com.
17.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Philips Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local Philips Semiconductors
sales office. In case of any inconsistency or conflict with the short data sheet,
the full data sheet shall prevail.
17.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, Philips Semiconductors does not give any representations
or warranties, expressed or implied, as to the accuracy or completeness of
such information and shall have no liability for the consequences of use of
such information.
Right to make changes — Philips Semiconductors reserves the right to
make changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — Philips Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a Philips Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. Philips Semiconductors accepts no liability for inclusion and/or use
of Philips Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Philips Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — Philips Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.semiconductors.philips.com/profile/terms, including those
pertaining to warranty, intellectual property rights infringement and limitation
of liability, unless explicitly otherwise agreed to in writing by Philips
Semiconductors. In case of any inconsistency or conflict between information
in this document and such terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
17.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
18. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: [email protected]
74AUP1Z125_1
Product data sheet
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Rev. 01 — 3 August 2006
26 of 27
74AUP1Z125
Philips Semiconductors
Low-power X-tal driver with enable and internal resistor
19. Contents
1
2
3
4
5
6
6.1
6.2
7
8
9
10
11
12
13
13.1
13.1.1
13.1.2
14
15
16
17
17.1
17.2
17.3
17.4
18
19
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . 3
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 4
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Dynamic characteristics . . . . . . . . . . . . . . . . . 12
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Application information. . . . . . . . . . . . . . . . . . 19
Crystal characteristics . . . . . . . . . . . . . . . . . . 19
Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 22
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25
Legal information. . . . . . . . . . . . . . . . . . . . . . . 26
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 26
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Contact information. . . . . . . . . . . . . . . . . . . . . 26
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© Koninklijke Philips Electronics N.V. 2006.
All rights reserved.
For more information, please visit: http://www.semiconductors.philips.com.
For sales office addresses, email to: [email protected].
Date of release: 3 August 2006
Document identifier: 74AUP1Z125_1