PHILIPS HCT4067

INTEGRATED CIRCUITS
DATA SHEET
For a complete data sheet, please also download:
• The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
• The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
• The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines
74HC/HCT4067
16-channel analog
multiplexer/demultiplexer
Product specification
File under Integrated Circuits, IC06
September 1993
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
The 74HC/HCT4067 are 16-channel analog
multiplexers/demultiplexers with four address inputs (S0 to
S3) , an active LOW enable input (E), sixteen independent
inputs/outputs (Y0 to Y15) and a common input/output (Z).
The ”4067” contains sixteen bidirectional analog switches,
each with one side connected to an independent
input/output (Y0 to Y15) and the other side connected to a
common input/output (Z).
With E LOW, one of the sixteen switches is selected (low
impedance ON-state) by S0 to S3. All unselected switches
are in the high impedance OFF-state. With E HIGH, all
switches are in the high impedance OFF-state,
independent of S0 to S3.
FEATURES
• Low “ON” resistance:
80 Ω (typ.) at VCC = 4.5 V
70 Ω (typ.) at VCC = 6.0 V
60 Ω (typ.) at VCC = 9.0 V
typical “break before make” built-in
• Output capability: non-standard
• ICC category: MSI
GENERAL DESCRIPTION
The 74HC/HCT4067 are high-speed Si-gate CMOS
devices and are pin compatible with the “4067” of the
“4000B” series. They are specified in compliance with
JEDEC standard no. 7A.
The analog inputs/outputs (Y0 to Y15, and Z) can swing
between VCC as a positive limit and GND as a negative
limit. VCC to GND may not exceed 10 V.
QUICK REFERENCE DATA
GND = 0 V; Tamb = 25 °C; tr = tf = 6 ns
TYPICAL
SYMBOL
PARAMETER
CONDITIONS
UNIT
HC
tPZL/ tPZH
tPLZ/ tPHZ
turn-on time
HCT
CL = 15 pF; RL = 1 kΩ; VCC = 5 V
E to Vos
26
32
ns
Sn to Vos
29
33
ns
E to Vos
27
26
ns
Sn to Vos
29
30
ns
3.5
3.5
pF
29
29
pF
independent (Y)
5
5
pF
common (Z)
45
45
pF
turn-off time
CI
input capacitance
CPD
power dissipation capacitance per switch
CS
max. switch capacitance
notes 1 and 2
Notes
1. CPD is used to determine the dynamic power dissipation (PD in µW):
PD = CPD × VCC2 × fi + ∑ { (CL + CS) × VCC2 × fo} where:
fi = input frequency in MHz
fo = output frequency in MHz
∑ {(CL + CS) × VCC2 × fo} = sum of outputs
CL = output load capacitance in pF
CS = max. switch capacitance in pF
VCC = supply voltage in V
2. For HC the condition is VI = GND to VCC
For HCT the condition is VI = GND to VCC − 1.5 V
September 1993
2
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
ORDERING INFORMATION
See “74HC/HCT/HCU/HCMOS Logic Package Information”.
PIN DESCRIPTION
PIN NO.
SYMBOL
NAME AND FUNCTION
1
Z
common input/output
9, 8, 7, 6, 5, 4, 3, 2, 23, 22, 21, 20, 19, 18, 17, 16
Y0 to Y15
independent inputs/outputs
10, 11, 14, 13
S0 to S3
address inputs
12
GND
ground (0 V)
15
E
enable input (active LOW)
24
VCC
positive supply voltage
Fig.1 Pin configuration.
September 1993
Fig.2 Logic symbol.
3
Fig.3 IEC logic symbol.
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
APPLICATIONS
• Analog multiplexing and demultiplexing
• Digital multiplexing and demultiplexing
• Signal gating
FUNCTION TABLE
INPUTS
Fig.4 Functional diagram.
E
S3
S2
S1
S0
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
L
H
L
H
Y0 − Z
Y1 − Z
Y2 − Z
Y3 − Z
L
L
L
L
L
L
L
L
H
H
H
H
L
L
H
H
L
H
L
H
Y4 − Z
Y5 − Z
Y6 − Z
Y7 − Z
L
L
L
L
H
H
H
H
L
L
L
L
L
L
H
H
L
H
L
H
Y8 − Z
Y9 − Z
Y10 − Z
Y11 − Z
L
L
L
L
H
H
H
H
H
H
H
H
L
L
H
H
L
H
L
H
Y12 − Z
Y13 − Z
Y14 − Z
Y15 − Z
H
X
X
X
X
none
Notes
1. H = HIGH voltage level
L = LOW voltage level
X = don’t care
Fig.5 Schematic diagram (one switch).
September 1993
4
CHANNEL
ON
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
Fig.6 Logic diagram.
September 1993
5
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Voltages are referenced to GND (ground = 0 V)
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VCC
DC supply voltage
−0.5
+11.0
V
±IIK
DC digital input diode current
20
mA
CONDITIONS
for VI < −0.5 or VI > VCC + 0.5 V
±ISK
DC switch diode current
20
mA
for VS < −0.5 or VS > VCC + 0.5 V
±IS
DC switch current
25
mA
for −0.5 V < VS < VCC + 0.5 V
±ICC; ±IGND
DC VCC or GND current
50
mA
Tstg
storage temperature range
+150
°C
Ptot
power dissipation per package
PS
−65
for temperature range: −40 to +125 °C
74HC/HCT
plastic DIL
750
mW
above +70 °C: derate linearly with 12 mW/K
plastic mini-pack (SO)
500
mW
above +70 °C: derate linearly with 8 mW/K
power dissipation per switch
100
mW
Note
1. To avoid drawing VCC current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across
the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC current will flow out
of terminals Yn. In this case there is no limit for the voltage drop across the switch, but the voltages at Yn and Z may
not exceed VCC or GND.
RECOMMENDED OPERATING CONDITIONS
74HC
74HCT
SYMBOL PARAMETER
UNIT
CONDITIONS
min. typ. max. min. typ. max.
VCC
DC supply voltage
2.0
5.0
VI
DC input voltage range
GND
VS
DC switch voltage range
GND
Tamb
operating ambient temperature range −40
Tamb
operating ambient temperature range −40
+125 −40
tr, tf
input rise and fall times
6.0
September 1993
6
10.0
4.5
VCC
5.5
V
GND
VCC
V
VCC
GND
VCC
V
+85
−40
+85
°C
1000
500
400
250
5.0
+125 °C
6.0
500
ns
see DC and AC
CHARACTERISTICS
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 10.0 V
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
DC CHARACTERISTICS FOR 74HC/HCT
For 74HC: VCC − GND = 2.0, 4.5, 6.0 and 9.0 V
For 74HCT: VCC − GND = 4.5 V
Tamb (°C)
TEST CONDITIONS
74HC/HCT
SYMBOL
PARAMETER
min.
+25
−40 to +85
typ.
max. min. max.
−40 to +125
min.
UNIT V
CC
(V)
IS
(µA)
Vis
VI
max.
RON
ON-resistance
(peak)
−
110
95
75
−
180
160
130
−
225
200
165
−
270
240
195
Ω
Ω
Ω
Ω
2.0
4.5
6.0
9.0
100
1000
1000
1000
VCC VIH
to
or
GND VIL
RON
ON-resistance (rail)
150
90
80
70
−
160
140
120
−
200
175
150
−
240
210
180
Ω
Ω
Ω
Ω
2.0
4.5
6.0
9.0
100
1000
1000
1000
GND VIH
or
or
VCC VIL
∆RON
maximum variation
of ON-resistance
between any two
channels
−
9
8
6
Ω
Ω
Ω
Ω
2.0
4.5
6.0
9.0
VCC VIH
to
or
GND VIL
Notes
1. At supply voltages (VCC − GND) approaching 2 V, the analog switch ON-resistance becomes extremely non-linear.
Therefore it is recommended that these devices be used to transmit digital signals only, when using these supply
voltages.
2. For test circuit measuring RON see Fig.7.
Fig.7 Test circuit for measuring ON-resistance (RON).
Fig.8 Test circuit for measuring OFF-state current.
September 1993
7
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
Fig.10 Typical ON-resistance
(RON) as a function of
input voltage (Vis) for
Vis = 0 to VCC − GND.
Fig.9 Test circuit for measuring ON-state current.
DC CHARACTERISTICS FOR 74HC
Voltages are referenced to GND (ground = 0 V)
Tamb (°C)
TEST CONDITIONS
74HC
SYMBOL PARAMETER
+25
min.
VIH
HIGH level input
voltage
VIL
LOW level input
voltage
±II
1.5
3.15
4.2
6.3
typ.
max.
1.2
2.4
3.2
4.7
−40 to +125
min.
min.
max.
1.5
3.15
4.2
6.3
UNIT
VCC
(V)
V
2.0
4.5
6.0
9.0
VI
OTHER
max.
1.5
3.15
4.2
6.3
0.50
1.35
1.80
2.70
0.50
1.35
1.80
2.70
0.50
1.35
1.80
2.70
V
2.0
4.5
6.0
9.0
input leakage
current
0.1
0.2
1.0
2.0
1.0
2.0
µA
6.0
10.0
VCC
or
GND
±IS
analog switch
OFF-state current
per channel
0.1
1.0
1.0
µA
10.0
VIH
or
VIL
VS =
VCC − GND
(see Fig.8)
±IS
analog switch
OFF-state current
all channels
0.8
8.0
8.0
µA
10.0
VIH
or
VIL
VS =
VCC − GND
(see Fig.9)
±IS
analog switch
ON-state current
0.8
8.0
8.0
µA
10.0
VIH
or
VIL
VS =
VCC − GND
(see Fig.9)
ICC
quiescent supply
current
8.0
16.0
80.0
160
160
320
µA
6.0
10.0
VCC Vis = GND
or VCC;
or
GND Vos = VCC
or GND
September 1993
0.8
2.1
2.8
4.3
−40 to +85
8
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
AC CHARACTERISTICS FOR 74HC
GND = 0 V; tr = tf = 6 ns; CL = 50 pF
Tamb (°C)
TEST CONDITIONS
74HC
SYMBOL PARAMETER
+25
−40 to +85
min. typ. max. min.
tPHL/ tPLH
max.
−40 to +125
UNIT
VCC
(V)
min. max.
propagation delay
Vis to Vos;
Yn to Z
25
9
7
5
75
15
13
9
95
19
16
11
110
22
19
14
ns
tPHL/ tPLH
propagation delay
Vis to Vos;
Z to Yn
18
6
5
4
60
12
10
8
75
15
13
10
90
18
15
12
ns
2.0
4.5
6.0
9.0
tPHZ/ tPLZ
turn-off time
E to Yn
74
27
22
20
250
50
43
38
315
63
54
48
375
75
64
57
ns
2.0
4.5
6.0
9.0
tPHZ/ tPLZ
turn-off time
Sn to Yn
83
30
24
21
250
50
43
38
315
63
54
48
375
75
64
57
ns
2.0
4.5
6.0
9.0
tPHZ/ tPLZ
turn-off time
E to Z
85
31
25
24
275
55
47
42
345
69
59
53
415
83
71
63
ns
2.0
4.5
6.0
9.0
tPHZ/ tPLZ
turn-off time
Sn to Z
94
34
27
25
290
58
47
45
365
73
62
56
435
87
74
68
ns
2.0
4.5
6.0
9.0
2.0
4.5
6.0
9.0
tPZH/ tPZL
turn-on time
E to Yn
80
29
23
17
275
55
47
42
345
69
59
53
415
83
71
63
ns
2.0
4.5
6.0
9.0
tPZH/ tPZL
turn-on time
Sn to Yn
88
32
26
18
300
60
51
45
375
75
64
56
450
90
77
68
ns
2.0
4.5
6.0
9.0
tPZH/ tPZL
turn-on time
E to Z
85
31
25
18
275
55
47
42
345
69
59
53
415
83
71
63
ns
2.0
4.5
6.0
9.0
tPZH/ tPZL
turn-on time
Sn to Z
94
34
27
19
300
60
51
45
375
75
64
56
450
90
77
68
ns
2.0
4.5
6.0
9.0
September 1993
9
OTHER
RL = ∞;
CL = 50 pF
(see Fig.16)
RL = 1 kΩ;
CL = 50 pF
(see Fig.17)
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
Note to AC CHARACTERISTICS FOR 74HC
1. Due to higher Z terminal capacitance (16 switches versus 1) the delay figures to the Z terminal are higher than those
to the Y terminal.
DC CHARACTERISTICS FOR 74HCT
Voltages are referenced to GND (ground = 0 V)
Tamb (°C)
TEST CONDITIONS
74HCY
SYMBOL PARAMETER
+25
−40 to +85
−40 to +125
UNIT V
CC
VI
(V)
OTHER
min. typ. max. min. max. min. max.
VIH
HIGH level input
voltage
VIL
LOW level input
voltage
±II
2.0
1.6
1.2
2.0
2.0
V
4.5
to
5.5
0.8
0.8
0.8
V
4.5
to
5.5
input leakage current
0.1
1.0
1.0
µA
5.5
VCC
or
GND
± IS
analog switch
OFF-state current per
channel
0.1
1.0
1.0
µA
5.5
VIH
or
VIL
VS =
VCC − GND
(see Fig.8)
±IS
analog switch
OFF-state current
all channels
0.8
8.0
8.0
µA
5.5
VIH
or
VIL
VS =
VCC − GND
(see Fig.9)
±IS
analog switch
ON-state current
0.8
8.0
8.0
µA
5.5
VIH
or
VIL
VS =
VCC − GND
(see Fig.9)
ICC
quiescent supply
current
8.0
80.0
160
µA
4.5
to
5.5
VCC
or
GND
Vis = GND or
VCC; Vos = VCC
or GND
∆ICC
additional quiescent
supply current per
input pin for unit load
coefficient is 1
(note 1)
100 360
450
490
µA
4.5
to
5.5
VCC
−2.1
V
other inputs at
VCC or GND
Note
1. The value of additional quiescent supply current (∆ICC) for a unit load of 1 is given here.
To determine ∆ICC per input, multiply this value by the unit load coefficient shown in the table below.
INPUT
UNIT LOAD COEFFICIENT
E
Sn
0.6
0.5
September 1993
10
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
AC CHARACTERISTICS FOR 74HCT
GND = 0 V; tr = tf = 6 ns
Tamb (°C)
TEST CONDITIONS
74HCT
SYMBOL PARAMETER
+25
−40 to +85
min. typ. max. min.
tPHL/ tPLH
15
max.
19
−40 to +125
UNIT
VCC
(V)
OTHER
min. max.
propagation delay
Vis to Vos;
Yn to Z
9
22
ns
4.5
tPHL/ tPLH
propagation delay
Vis to Vos;
Z to Yn
6
12
15
18
ns
4.5
tPHZ/ tPLZ
turn-off time
E to Yn
26
55
69
83
ns
4.5
tPHZ/ tPLZ
turn-off time
Sn to Yn
31
55
69
83
ns
4.5
tPHZ/ tPLZ
turn-off time
E to Z
30
60
75
90
ns
4.5
tPHZ/ tPLZ
turn-off time
Sn to Z
35
60
75
90
ns
4.5
tPZH/ tPZL
turn-on time
E to Yn
32
60
75
90
ns
4.5
tPZH/ tPZL
turn-on time
Sn to Yn
35
60
75
90
ns
4.5
tPZH/ tPZL
turn-on time
E to Z
38
65
81
98
ns
4.5
tPZH/ tPZL
turn-on time
Sn to Z
38
65
81
98
ns
4.5
RL = ∞;
CL = 50 pF
(see Fig.16)
RL = 1 kΩ;
CL = 50 pF
(see Fig.17)
Note
1. Due to higher Z terminal capacitance (16 switches versus 1) the delay figures to the Z terminal are higher than those
to the Y terminal.
September 1993
11
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
ADDITIONAL AC CHARACTERISTICS FOR 74HC/HCT
Recommended conditions and typical values
GND = 0 V; tr = tf = 6 ns
SYMBOL
VCC
(V)
Vis(p-p)
(V)
PARAMETER
TYP.
UNIT
sine-wave distortion
f = 1 kHz
0.04
0.02
%
%
4.5
9.0
4.0
8.0
RL = 10 kΩ; CL = 50 pF
(see Fig.14)
sine-wave distortion
f = 10 kHz
0.12
0.06
%
%
4.5
9.0
4.0
8.0
RL = 10 kΩ; CL = 50 pF
(see Fig.14)
switch “OFF” signal
feed-through
−50
−50
dB
dB
4.5
9.0
note 3
RL = 600 Ω; CL = 50 pF
f = 1 MHz (see Figs 11 and 15)
fmax
minimum frequency response
(−3 dB)
90
100
MHz
MHz
4.5
9.0
note 4
RL = 50 Ω; CL = 10 pF
(see Figs 12 and 13)
CS
maximum switch capacitance
independent (Y)
common (Z)
5
45
pF
pF
CONDITIONS
Notes
1. Vis is the input voltage at Yn or Z terminal, whichever is assigned as an input.
2. Vos is the output voltage at Yn or Z terminal, whichever is assigned as an output.
3. Adjust input voltage Vis is 0 dBm level (0 dBm = 1 mW into 600 Ω).
4. Adjust input voltage Vis is 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 Ω).
September 1993
12
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
Test conditions:
VCC = 4.5 V; GND = 0 V;
RL = 50 Ω; Rsource = 1 kΩ.
Fig.11 Typical switch ”OFF” signal feed-through as a function of frequency.
Test conditions:
VCC = 4.5 V; GND = 0 V;
RL = 50 Ω; Rsource = 1 kΩ.
Fig.12 Typical frequency response.
Adjust input voltage to obtain
0 dBm at Vos when fin = 1 MHz.
After set-up frequency of fin is
increased to obtain a reading of
−3 dB at Vos.
Fig.13 Test circuit for measuring minimum frequency response.
September 1993
13
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
Fig.15 Test circuit for measuring switch “OFF”
signal feed-through.
Fig.14 Test circuit for measuring sine-wave
distortion.
AC WAVEFORMS
(1) HC : VM = 50%; VI = GND to VCC.
HCT : VM = 1.3 V; VI = GND to 3 V.
Fig.17 Waveforms showing the turn-on and
turn-off times.
Fig.16 Waveforms showing the input (Vis) to output
(Vos) propagation delays.
September 1993
14
Philips Semiconductors
Product specification
16-channel analog
multiplexer/demultiplexer
74HC/HCT4067
TEST CIRCUIT AND WAVEFORMS
Conditions
TEST
SWITCH
Vis
tPZH
tPZL
tPHZ
tPLZ
others
GND
VCC
GND
VCC
open
VCC
GND
VCC
GND
pulse
CL
=
load capacitance including jig and
probe capacitance (see AC
CHARACTERISTICS for values).
RT
=
termination resistance should be equal
to the output impedance ZO of the
pulse generator.
tr
=
tf = 6 ns, when measuring fmax, there is
no constraint on tr, tf with 50% duty
factor.
Fig.18 Test circuit for measuring AC performance.
tr, tf
FAMILY
AMPLIVM
TUDE
74HC
VCC
50%
< 2 ns
6 ns
74HCT
3.0 V
1.3 V < 2 ns
6 ns
fmax;
OTHER
PULSE WIDTH
Fig.19 Input pulse definitions.
PACKAGE OUTLINES
See “74HC/HCT/HCU/HCMOS Logic Package Outlines”.
September 1993
15