TC74LCX273F/FW/FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74LCX273F,TC74LCX273FW,TC74LCX273FT Low-Voltage Octal D-Type Flip-Flop with Clear with 5-V Tolerant Inputs and Outputs The TC74LCX273F/FW/FT is a high-performance CMOS octal D-type flip-flop. Designed for use in 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low-power dissipation. The device is designed for low-voltage (3.3 V) VCC applications, but it could be used to interface to 5-V supply environment for both inputs and outputs. This 8 bit D-type flip-flop is controlled by a clock input (CK) and a clear input (CLR). When the CLR input is low, the eight outputs are at a low logic level. All inputs are equipped with protection circuits against static discharge. Note: xxxFW (JEDEC SOP) is not available in Japan. TC74LCX273F TC74LCX273FW Features · Low-voltage operation: VCC = 2.0 to 3.6 V · High-speed operation: tpd = 8.5 ns (max) (VCC = 3.0 to 3.6 V) · Output current: |IOH|/IOL = 24 mA (min) (VCC = 3.0 V) · Latch-up performance: ±500 mA · Available in JEDEC SOP, JEITA SOP and TSSOP · Power-down protection is provided on all inputs and outputs · Pin and function compatible with the 74 series TC74LCX273FT (74AC/VHC/HC/F/ALS/LS etc.) 273 type Weight SOP20-P-300-1.27: 0.22 g (typ.) SOL20-P-300-1.27: 0.46 g (typ.) TSSOP20-P-0044-0.65: 0.08 g (typ.) 1 2002-01-11 TC74LCX273F/FW/FT Pin Assignment (top view) IEC Logic Symbol 1 20 VCC Q1 2 19 Q8 D1 3 18 D8 D2 4 17 D7 Q2 5 16 Q7 Q3 6 15 Q6 D3 7 14 D6 D4 8 13 D5 Q4 9 12 Q5 GND 10 11 CK CLR CLR CK D0 D1 D2 D3 D4 D5 D6 D7 (1) (11) (3) (4) (7) (8) (13) (14) (17) (18) R C1 (2) (5) (6) (9) (12) (15) (16) (19) 1D Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Truth Table Inputs Outputs Function CLR D CK Q L X X L Clear H L L ¾ H H H ¾ H X Qn No change X: Don’t care System Diagram CLR 1 D1 3 D2 4 D R CK CK D3 7 D R CK Q D4 8 D R CK Q D5 13 D R CK Q D6 14 D R CK Q D7 17 D R CK Q D8 18 D R CK Q D R CK Q Q 11 2 5 6 9 Q1 Q2 Q3 Q4 2 12 Q5 15 Q6 19 16 Q7 Q8 2002-01-11 TC74LCX273F/FW/FT Maximum Ratings Characteristics Symbol Rating Unit Power supply voltage VCC -0.5 to 7.0 V DC input voltage VIN -0.5 to 7.0 V DC output voltage VOUT -0.5 to 7.0 (Note 1) -0.5 to VCC + 0.5 V (Note 2) Input diode current IIK -50 Output diode current IOK ±50 DC output current IOUT ±50 mA Power dissipation PD 180 mW ICC/IGND ±100 mA Tstg -65 to 150 °C DC VCC/ground current Storage temperature mA (Note 3) mA Note 1: VCC = 0 V Note 2: High or low state. IOUT absolute maximum rating must be observed. Note 3: VOUT < GND, VOUT > VCC Recommended Operating Conditions Characteristics Symbol Power supply voltage VCC Input voltage VIN Output voltage Output current Rating Unit 2.0 to 3.6 -1.5 to 3.6 (Note 4) 0 to 5.5 V 0 to 5.5 (Note 5) VOUT V V 0 to VCC (Note 6) IOH/IOL ±24 (Note 7) ±12 (Note 8) Operating temperature Topr -40 to 85 Input rise and fall time dt/dv 0 to 10 mA °C (Note 9) ns/V Note 4: Data retention only Note 5: VCC = 0 V Note 6: High or low state Note 7: VCC = 3.0 to 3.6 V Note 8: VCC = 2.7 to 3.0 V Note 9: VIN = 0.8 to 2.0 V, VCC = 3.0 V 3 2002-01-11 TC74LCX273F/FW/FT Electrical Characteristics DC Characteristics (Ta = -40 to 85°C) Characteristics Symbol Test Condition Min Max Unit VCC (V) Input voltage H-level VIH 2.7 to 3.6 2.0 ¾ L-level VIL 2.7 to 3.6 ¾ 0.8 IOH = -100 mA 2.7 to 3.6 VCC - 0.2 ¾ IOH = -12 mA 2.7 2.2 ¾ IOH = -18 mA 3.0 2.4 ¾ IOH = -24 mA 3.0 2.2 ¾ IOL = 100 mA 2.7 to 3.6 ¾ 0.2 IOL = 12 mA 2.7 ¾ 0.4 IOL = 16 mA 3.0 ¾ 0.4 IOL = 24 mA 3.0 ¾ 0.55 2.7 to 3.6 ¾ ±5.0 mA VIN/VOUT = 5.5 V 0 ¾ 10.0 mA VIN = VCC or GND 2.7 to 3.6 ¾ 10.0 VIN = 3.6 to 5.5 V 2.7 to 3.6 ¾ ±10.0 VIN = VCC - 0.6 V 2.7 to 3.6 ¾ 500 Min Max 2.7 ¾ ¾ 3.3 ± 0.3 150 ¾ 2.7 ¾ 9.5 3.3 ± 0.3 1.5 8.5 2.7 ¾ 9.5 3.3 ± 0.3 1.5 8.5 2.7 3.3 ¾ 3.3 ± 0.3 3.3 ¾ 2.7 3.3 ¾ 3.3 ± 0.3 3.3 ¾ 2.7 2.5 ¾ 3.3 ± 0.3 2.5 ¾ 2.7 1.5 ¾ 3.3 ± 0.3 1.5 ¾ 2.7 2.5 ¾ 3.3 ± 0.3 2.0 ¾ 2.7 ¾ ¾ 3.3 ± 0.3 ¾ 1.0 H-level VOH VIN = VIH or VIL Output voltage L-level Input leakage current VOL IIN Power-off leakage current IOFF Quiescent supply current ICC Increase in Icc per input DICC VIN = VIH or VIL VIN = 0 to 5.5 V V V mA AC Characteristics (Ta = -40 to 85°C) Characteristics Symbol Test Condition Unit VCC (V) Maximum clock frequency Propagation delay time (CK-Q) fMAX tPLH (Figure 1, Figure 2) (Figure 1, Figure 2) tPHL Propagation delay time ( CLR -Q) Minimum pulse width (CK) tPHL tw (H) (Figure 1, Figure 3) (Figure 1, Figure 2) tw (L) Minimum pulse width ( CLR ) Minimum setup time Minimum hold time Minimum removal time Output to output skew tw (L) (Figure 3) ts (Figure 1, Figure 2) th (Figure 1, Figure 2) trem (Figure 4) tosLH (Note 10) tosHL MHz ns ns ns ns ns ns ns ns Note 10: Parameter guaranteed by design. (tosLH = |tpLHm - tpLHn|, tosHL = |tpHLm - tpHLn|) 4 2002-01-11 TC74LCX273F/FW/FT Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.5 ns, CL = 50 pF, RL = 500 W) Characteristics Test Condition Symbol Typ. Unit VCC (V) Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL VIH = 3.3 V, VIL = 0 V 3.3 0.8 V ïVOLVï VIH = 3.3 V, VIL = 0 V 3.3 0.8 V Typ. Unit 3.3 7 pF 0 8 pF 3.3 25 pF VOLP Capacitive Characteristics (Ta = 25°C) Characteristics Test Condition Symbol VCC (V) Input capacitance Output capacitance Power dissipation capacitance CIN ¾ COUT CPD fIN = 10 MHz (Note 11) Note 11: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/8 (per bit) 5 2002-01-11 TC74LCX273F/FW/FT AC Test Circuit Measure RL CL Output CL = 50 pF RL = 500 W Figure 1 AC Waveform tr 2.5 ns tf 2.5 ns 2.7 V 90% 1.5 V Input (CK) 10% GND tr 2.5 ns tf 2.5 ns tw (H) tw (L) 2.7 V 90% Input (D) 10% 1.5 V ts (H) th (H) ts (L) GND th (L) VOH Output (Q) 1.5 V Figure 2 VOL tpLH tpHL tpLH, tpHL, tw, ts, th tr 2.5 ns VIH Input ( CLR ) Input ( CLR ) GND tw (L) VIH 90% 1.5 V 10% GND tr 2.5 ns VOH Output (Q) Output (CK) 1.5 V VOL tpHL Figure 3 90% 10% VIH 1.5 V GND trem tpHL Figure 4 6 trem 2002-01-11 TC74LCX273F/FW/FT Package Dimensions Weight: 0.22 g (typ.) 7 2002-01-11 TC74LCX273F/FW/FT Package Dimensions Note: This package is not available in japan. Weight: 0.46 g (typ.) 8 2002-01-11 TC74LCX273F/FW/FT Package Dimensions Weight: 0.08 g (typ.) 9 2002-01-11 TC74LCX273F/FW/FT RESTRICTIONS ON PRODUCT USE 000707EBA · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The products described in this document are subject to the foreign exchange and foreign trade laws. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 10 2002-01-11