STMICROELECTRONICS 74V1G80CTR

74V1G80
SINGLE POSITIVE EDGE TRIGGERED
D-TYPE FLIP-FLOP
■
■
■
■
■
■
■
■
HIGH SPEED:
fMAX = 180MHz (TYP.) at VCC = 5V
LOW POWER DISSIPATION:
ICC = 1µA(MAX.) at TA=25°C
HIGH NOISE IMMUNITY:
VNIH = V NIL = 28% VCC (MIN.)
POWER DOWN PROTECTION ON INPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 8mA (MIN) at VCC = 4.5V
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
OPERATING VOLTAGE RANGE:
VCC(OPR) = 2V to 5.5V
IMPROVED LATCH-UP IMMUNITY
DESCRIPTION
The 74V1G80 is an advanced high-speed CMOS
SINGLE POSITIVE EDGE TRIGGERED D-TYPE
FLIP-FLOP
WITH
INVERTED
OUTPUT
fabricated with sub-micron silicon gate and
double-layer metal wiring C2MOS technology. it is
designed to operate from 2V to 5.5V, making this
device ideal for portable applications.
This D-Type flip-flop is controlled by a clock input
(CK). On the positive transition of the clock, the Q
output will be set to the logic inverted state that
was setup at the D input.
SOT23-5L
SOT323-5L
ORDER CODES
PACKAGE
T&R
SOT23-5L
SOT323-5L
74V1G80STR
74V1G80CTR
Following the hold time interval, data at the D input
can be changed without affecting the level at the
output. Power down protection is provided on
input and 0 to 7V can be accepted on input with no
regard to the supply voltage. This device can be
used to interface 5V to 3V.
It’s available in the commercial temperature
range. All inputs and output are equipped with
protection circuits against static discharge, giving
them ESD immunity and transient excess voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
July 2001
1/10
74V1G80
INPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No
SYMBOL
NAME AND FUNCTION
1
D
2
CK
4
3
Q
GND
VCC
Data Input
Clock Input (Positive
Edge)
Inverted Flip-Flop Output
Ground (0V)
5
Positive Supply Voltage
TRUTH TABLE
D
CK
Q
L
H
H
L
L
Qn
H
Qn
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
Value
Unit
-0.5 to +7.0
V
-0.5 to +7.0
V
-0.5 to VCC + 0.5
- 20
V
mA
IIK
DC Input Diode Current
IOK
DC Output Diode Current
± 20
mA
IO
DC Output Current
± 25
mA
ICC or IGND DC VCC or Ground Current
Tstg
Storage Temperature
TL
Lead Temperature (10 sec)
± 50
mA
-65 to +150
°C
260
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
Unit
2 to 5.5
V
VI
Input Voltage
0 to 5.5
V
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
dt/dv
Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V)
(VCC = 5.0 ± 0.5V)
1) VIN from 30% to 70% of V CC
2/10
Value
-55 to 125
°C
0 to 100
0 to 20
ns/V
ns/V
74V1G80
DC SPECIFICATIONS
Test Condition
Symbol
VIH
VIL
VOH
VOL
II
ICC
Parameter
High Level Input
Voltage
Low Level Input
Voltage
High Level Output
Voltage
Low Level Output
Voltage
Input Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
2.0
3.0 to
5.5
2.0
3.0 to
5.5
Typ.
Max.
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
1.5
1.5
1.5
0.7VCC
0.7VCC
0.7VCC
Unit
Max.
V
0.5
0.5
0.5
0.3VCC
0.3VCC
0.3VCC
V
2.0
IO=-50 µA
1.9
2.0
1.9
1.9
3.0
IO=-50 µA
2.9
3.0
2.9
2.9
4.5
IO=-50 µA
4.4
4.5
3.0
IO=-4 mA
2.58
4.5
IO=-8 mA
3.94
2.0
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=50 µA
0.0
0.1
0.1
0.1
4.5
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=4 mA
0.36
0.44
0.55
4.5
IO=8 mA
0.36
0.44
0.55
0 to
5.5
VI = 5.5V or GND
± 0.1
±1
±1
µA
5.5
VI = VCC or GND
1
10
20
µA
4.4
4.4
2.48
2.4
3.8
V
3.7
V
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns)
Test Condition
Symbol
Parameter
tPLH tPHL Propagation Delay
Time CK to Q
tW
ts
th
fMAX
CK Pulse Width,
HIGH or LOW
Setup Time D to
CK, HIGH or LOW
Hold Time D to CK,
HIGH or LOW
Maximum Clock
Frequency
VCC
(V)
CL
(pF)
Value
TA = 25°C
Min.
Typ.
-40 to 85°C
-55 to 125°C
Max.
Min.
Max.
Min.
Max.
(*)
15
4.9
8.4
1.0
9.8
1.0
10.8
3.3(*)
50
5.9
12.0
1.0
14.0
1.0
15.0
5.0(**)
15
3.5
5.6
1.0
7.0
1.0
8.0
5.0(**)
50
4.5
8.0
1.0
10.0
1.0
11.0
3.3
(*)
4.0
4.0
4.0
(**)
5.0
3.0
3.0
3.0
3.3(*)
4.0
4.0
4.0
5.0(**)
3.0
3.0
3.0
3.3(*)
1.0
1.0
1.0
(**)
1.0
1.0
1.0
3.3
5.0
3.3(*)
50
100
120
90
90
5.0(**)
50
165
180
150
150
Unit
ns
ns
ns
ns
MHz
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
3/10
74V1G80
CAPACITIVE CHARACTERISTICS
Test Condition
Symbol
Value
TA = 25°C
Parameter
Min.
Typ.
Max.
10
CIN
Input Capacitance
4
CPD
Power Dissipation
Capacitance
(note 1)
8
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
10
Unit
Max.
10
pF
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC
TEST CIRCUIT
CL = 15/50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
4/10
74V1G80
WAVEFORM: PROPAGATION DELAY, SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle)
5/10
74V1G80
SOT23-5L MECHANICAL DATA
mm.
mils
DIM.
MIN.
MAX.
MIN.
TYP.
MAX.
A
0.90
1.45
35.4
57.1
A1
0.00
0.15
0.0
5.9
A2
0.90
1.30
35.4
51.2
b
0.35
0.50
13.7
19.7
C
0.09
0.20
3.5
7.8
D
2.80
3.00
110.2
118.1
E
2.60
3.00
102.3
118.1
E1
1.50
1.75
59.0
68.8
e
0.95
37.4
e1
1.9
74.8
L
6/10
TYP
0.35
0.55
13.7
21.6
74V1G80
SOT323-5L MECHANICAL DATA
mm.
mils
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
0.80
1.10
31.5
43.3
A1
0.00
0.10
0.0
3.9
A2
0.80
1.00
31.5
39.4
b
0.15
0.30
5.9
11.8
C
0.10
0.18
3.9
7.1
D
1.80
2.20
70.9
86.6
E
1.80
2.40
70.9
94.5
E1
1.15
1.35
45.3
53.1
e
0.65
25.6
e1
1.3
51.2
L
0.10
0.30
3.9
11.8
7/10
74V1G80
Tape & Reel SOT23-xL MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MIN.
TYP.
180
13.0
13.2
MAX.
7.086
C
12.8
D
20.2
0.795
N
60
2.362
T
8/10
MAX.
0.504
0.512
14.4
0.519
0.567
Ao
3.13
3.23
3.33
0.123
0.127
0.131
Bo
3.07
3.17
3.27
0.120
0.124
0.128
Ko
1.27
1.37
1.47
0.050
0.054
0.0.58
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
3.9
4.0
4.1
0.153
0.157
0.161
74V1G80
Tape & Reel SOT323-xL MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
175
180
185
6.889
7.086
7.283
C
12.8
13
13.2
0.504
0.512
0.519
D
20.2
N
59.5
0.795
60
T
60.5
2.362
14.4
0.567
Ao
2.25
0.088
Bo
2.7
0.106
Ko
1.2
0.047
Po
3.98
4
4.2
0.156
0.157
0.165
P
3.98
4
4.2
0.156
0.157
0.165
9/10
74V1G80
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
© http://www.st.com
10/10