KYL KYL-300H_1

Shenzhen KYL Communication Equipment Co., Ltd
KYL-300H High Speed Data Radio Module
Shenzhen KYL Communication Equipment Co., Ltd
Address: C3705-3707, Huangdu Square, South of Exhibition Center, Yitian Road, Futian
District, Shenzhen, Guangdong, China 518048
Tel: 86-755-82943662
Fax: 86-755-83408785
Skype:KYL-Sunny
Yahoo messenger: [email protected]
MSN: [email protected]
Email: [email protected]
Website: http://www.rf-data.com
Fax: +86-755-82943662
[email protected]
www.rf-data.com
1
Shenzhen KYL Communication Equipment Co., Ltd
Before using our products, please read the user manual carefully.
Any questions, please contact us at the above mentioned ways.
.
I. Features of KYL-300H
1. Low power transmission: 5W (default), 6W~7W (optional).
2. Carrier frequency: 433MHz (default), 400-470MHz (optional)
3. High anti- interference and Low BER (Bit Error Rate)
Based on GFSK modulation, high-efficiency forward error correction channel encoding
technology is used to ensure the data’s resistance against both transient interference and
random interference. The actual BER can be achieved to 10-5~ 10-6 when channel BER is
10-2.
4. Long Transmission Distance
Within the visible range, when the height of antenna is higher than 2m and the BER is
10-3, the reliable transmission distance is 10km @1200bps and [email protected]
respectively.
5. Transparent data transmission
Transparent data interface used in transceivers is to satisfy many standard and
nonstandard user protocols. Any false data generated in air can be filtrated automatically
(What has been received is exactly what has been transmitted).
6. Multi-channels
KYL-300H provides 8 channels, expandable for 16, 32 channels according to
requirements of users.
7. 2 ports with three connection methods
KYL-300H transceivers provide 2 ports with three connections: a UART interface of
TTL level, a non-standard RS-232 port and a non-standard RS-485 port.
8. Big data buffer area
With optional interface baud rates: 1200/4800/9600/19200bps and 8N1/8E1/8O1 data
format (decide by user), the transceiver can transmit unlimited data frames with flexible
user program.
Note: the RF data rate is only settled down before delivery; please specify our sales your
requirements when placing your orders.
9. Intelligent data control system and no other extra programs required
Even for half duplex communication, no other excessive programs are required. All RF
system data transmission/reception and other On-the-Fly conversion and control are
performed by KYL-300H transceivers automatically.
10. Lower power consumption & nice sleep function
With +12V power, the receiving current is less than 30mA, the transmitting current is
less than 1.5A, and the sleeping current is less than 1mA.
11. High reliability, small size and excellent performance
By using monolithic radio-frequency integrated circuit and single-chip MCU, the
transceivers have less peripheral circuits, high reliability, and low failure rate.
12. Various options for configurable antennas.
Fax: +86-755-82943662
[email protected]
www.rf-data.com
2
Shenzhen KYL Communication Equipment Co., Ltd
II. Applications of KYL-300H
KYL-300H is suitable for:
* Automatic Meter Reading (AMR);
* Wireless alarm and security systems;
* Building automation, security systems, wireless monitor, remote control and access
control system;
* Wireless data transmission, automatic data collection system;
* Radio modem can be used for Sports training & competition;
* Wireless dishes ordering;
* Wireless POS, PDA wireless smart terminal;
* RF module can be used for electronic bus station and intelligent traffics;
* RF transmitter, Wireless electronic display screen and Queuing machine;
* Wireless telemetry; charging for parking, parking lot;
* Wireless modem automobile inspection and four-wheel orientation;
* Wireless sensor, Industrial wireless remote control and air conditioning remote
controller;
* Data communication in the aspects of railway, oil field, dock and army.
* LED display in thruway and public place;
* Point to multi-point wireless network, wireless on-the-spot bus and automatic data
collection system
III. How to use KYL-300H
KYL-300H can provides RS-232,RS-485 and TTL level interface port for direct connection
with PC, RS485 devices, monolithic processors. The schematic diagram is shown below:
1. Power supply
The factory default setting is +12, ±1.2V DC. By using better ripple factor, KYL-300H
transceivers can also share power supply with other equipment. If possible, a
voltage-stabilizing chip with 12V voltage is much more recommended than Switch
power supply. But if only switch power supply available, the jam caused by switch
pulse to the transceivers should be avoided. In addition, the reliable grounding must be
used if there is other device in the system equipment. In case of failing to connect with
the ground, it can form its own grounding but must be absolutely separated from the
municipal electric supply.
Fax: +86-755-82943662
[email protected]
www.rf-data.com
3
Shenzhen KYL Communication Equipment Co., Ltd
2. Connection Definition with terminal
KYL-300H transceivers supply one 9-pin connector (JP1), their definitions and
connection methods with terminals are shown in Table 1.
Table 1: JP1 Pin Definitions and connection methods
Pin No. Signal Name
Function
Level
Connection
with terminal
Ground
1
GND
Grounding of power supply
2
Vcc
Power supply DC
5V
3
RxD/TTL
Serial data input to the transceiver
TTL
TxD
4
TxD/TTL
TTL
RxD
5
SGND
Transmitted data out of the
transceiver
Signal
6
A (TXD)
A of RS-485(TxD of RS-232)
A(RxD)
7
B (RXD)
B of RS-485(RxD of RS-232)
B(TxD)
8
SLEEP
Sleep control (input)
TTL
9
RESET
Reset signal(input)
TTL
Sleep signal
Remarks
High level
sleep
Negative
pulse reset
3. The connection schematic diagram of KYL-300H transceivers with terminal.
VCC 12V
GND
9
1
4. Setting of channel, interface and data format:
Before using KYL-300H, the user needs to make simple configuration based on its own
needs to determine the channel, interface mode and data format.
The user can change or view the module's interface baud rate, channel and address code.
Fax: +86-755-82943662
[email protected]
www.rf-data.com
4
Shenzhen KYL Communication Equipment Co., Ltd
Parameter setting or reading as per the testing software KYLPRO.exe in the PC (in
products box).And the configuration is as follows:
i. Channel configuration:
Channel No.
Frequency
Channel No.
Frequency
1
429.0325MHZ
5
433.0325MHZ
2
430.0325MHZ
6
434.0325MHZ
3
431.0325MHZ
7
435.0325MHZ
4
432.0325MHZ
8
436.0325MHZ
Note: the frequency points corresponding to each channel can be adjusted based on the
user’s needs.
5. The Function-indicator light
a. The LED indicator light will glitter red for 0.5S once after switched on.
b. The LED indicator light will glitter green continually while receiving data from air.
c. The LED indicator light will glitter red continuously when transmitting data into air
after receiving from COM.
d. If the module enables the sleep function, LED indicator light is always dark.
6. Supported protocol and Transmit capability
KYL-300H standard transceivers offer transparent protocol to support various
applications and protocols of users. If the user needs to decrease his cost or ease the
workload of terminal CPU, we can add other specific functions based on the transparent
protocol, such as addressing, data acquisition, command interpretation, etc.
7. Sleep function instruction:
Due to reducing more consumption, KYL-300H transceivers support Sleep function. In
sleep mode, the current consumption is less than 1mA.
a. How to use the Sleep function:
The Pin8 ‘SLP’ in JP1 is the signal of sleep control. In high power level, transceiver
stays in working mode. In low power level (<0.5V), transceiver stays in sleep mode.
The SLP signal can convert transceiver from working to sleep mode in 1ms after
falling edge. If the Sleep signal arrives when the transceiver is transmitting data, the
module will enter sleep mode after finishing transmission. From sleep mode to
working, it takes the transceiver 1ms after rising edge.
To disable the opened sleep function of KYL-300H, the SLP (SLEEP) pin should be
definitely connected with 0 or ground.
b. Attentions about use of sleep function:
When the sleep function enabled, any supply glitches, such as switch dithering, fire
striking or quick switching on and off, could cause the transceiver to be switched to
the wrong sleep mode.
After switching on, users can avoid this error by making a compulsive restoration
once after the CPU delays 100ms.
Sleep Timing Diagram:
Fax: +86-755-82943662
[email protected]
www.rf-data.com
5
Shenzhen KYL Communication Equipment Co., Ltd
8. The attentions of data transmission
a. The delay time (tc) of conversion between transmitting and receiving is less than
1ms.
Timing diagram:
b. The delay time of transceivers between the first bit sent by TxD to the first bit
received by RxD.
Due to a data processing will be made on user’s data by KYL-300H transceiver using
FEC (Forward Error Correction) or other correction algorithm, when RxD of a
KYL-300H transceiver ‘A’ receives the data, then transmits it, the other one
transceiver ‘B’ will have a delay (ts) to receive and transmit by TxD. Different RF
data rate causes different delay time. Please see the specific delay time below:
RF Date Rate
(bps)
1200
Delay
Ts(mS)
90
RF Date Rate
(bps)
9600
Delay
Ts(mS)
16
2400
48
19200
10
4800
30
Fax: +86-755-82943662
[email protected]
www.rf-data.com
6
Shenzhen KYL Communication Equipment Co., Ltd
Timing diagram:
c. Error dealing procedure:
To enhance the reliability and stability of user’s systems, a verify bit or a Cyclic
Redundancy Check (CRC) mode is highly recommended to resent the wrong
information while using KYL-300H modules.
d. Large-number data transmission
In theory, when the interface data rate is faster than the RF data rate, KYL-300H
transceivers can sent unlimited-long data package, but any long packages more than
120B are not recommended. The length of each package should be between 60~100B.
We also recommend user to resent the wrong information using Automatic Error
Request Equipment (ARQ).
The analyzing as below:
What if the actual transmission BER (Bit Error Rate) is 10-4, 1 packet with 1KB data,
which is about 10-thousand bits, is sent, theoretically, at least 1 bit will be received
wrongly, then the 1KB information will never be received correctly.
But if we package the data into 10 packets with 100B for each, when all 10 packets
are sent, there will be only 1 packet wrong according to this probability. After that,
resend this wrong packet using ARQ mode. So by resending one more packet and the
efficiency rate is reduced 10%, all data will be absolutely received correctly.
9. Antenna configuration:
Many appropriative antennas for low power RF modules are selected for meeting
different user antenna configurations. Please ask our Sales office for further
information about the antenna’s dimension and performance.
a. Helical SMA antennas
KYL-ANT-433-10-SMA: 100mm helical SMA antennas with high gain and low cost,
reach a long distance.
Fax: +86-755-82943662
[email protected]
www.rf-data.com
7
Shenzhen KYL Communication Equipment Co., Ltd
KYL-ANT-433-3-SMA: 28mm SMA helical antenna with magnetic core, small size,
beautiful appearance (like the mobile phone antenna)
KYL-ANT-433-10-ZSMA: 100mm SMA helical antenna with folding joint, easy for
adjusting the direction and fixing.
b. Magnetic vehicle antenna
KYL-ANT-O433S-300H1.5-SMA: include magnetic antenna base, suitable for
equipment with metal shell, easy for fixing, effective to enhance the transmission
distance.
More kinds of antennas please go to our website our website:
http://www.rf-data.com/Products_list_en.asp?classid=163
If you have special demands on antennas, please specify, we can design and produce for
you individually.
IV. Network Application of KYL-300H
The communication channel of KYL-300H is half duplex, which is most suitable for
the communication mode of point to multi-point. Under this mode, one master station
must be set, and all of the rest are slave stations. A unique address is given to each
station. The coordination of communication is controlled by master station that uses
data frames containing address code to transmit data or command. Slave station will
receive all of the data and command and compare the received address code with local
address code. If they are different, the data will be deserted without any response. If
Fax: +86-755-82943662
[email protected]
www.rf-data.com
8
Shenzhen KYL Communication Equipment Co., Ltd
those address codes are the same, it means the data is sent to the local. Slave station
will make different responses according to the transmitted data or command and send
back the data of response. All these jobs must be performed by upper protocol, and it
is assured that there is only one transmitter-receiver in the state of transmission in the
communication network at any instant moment so as to avoid the cross-interference.
KYL-300H can also be used for point-to-point communication with easier operation.
For the programming of serial port, all you have to do is to remember that its
communication mode is semi duplex while always observing the time sequence of
come-and-go for receiving and transmitting.
V. Technical specification of KYL-300H
* Modulation mode: GFSK/FSK
* Working frequency: 400MHz~470MHz
* Power supply: DC 12V(±10%)
* RF power: ≤5W;
* RF data rate: 1200/2400/4800/9600/19200bps (Set before delivery);
* Receive current: <30Ma (TTL connect);
* Receive sensitivity: -123dBm (1200bps); -118dBm (9600bps);
* Transmitting current: <1.5A;
* Sleep current: <1mA;
* Interface data format: 8E1/8N1/8O1;
* Working temperature: -35~+75 (industrial)
* RF Line-of-sight Range: 8km ([email protected]);
10km([email protected]);
* Size: 85mm*58mm*16mm (without antenna port).
VI. Description of type
KYL-300H-96
Manufacture
Fax: +86-755-82943662
Type
Baud Rate
12:1200bps
24:2400bps
48:4800bps
96:9600bps
192:19200bps
[email protected]
www.rf-data.com
9