UNISONIC TECHNOLOGIES CO., LTD 7106 CMOS IC 3½ DIGIT, LCD DISPLAY, A/D CONVERTERS DESCRIPTION The UTC 7106 is a high performance, low power,3½ digits A/D converter. Included are seven segment decoders, display drivers, a reference, and a clock. The UTC 7106 is designed to interface with a liquid crystal display (LCD) and includes a multiplexed backplane drive. The UTC 7106 bring together a combination of high accuracy, versatility, and true economy. It features auto zero to less than 10μV, zero drift of less than 1μV/°C, input bias current of 10pA (Max), and rollover error of less than one count. True differential inputs and reference are useful in all system, but give the designer an uncommon advantage when measuring load cells, strain gauges and other bridge type transducers. Finally, the true economy of single power supply operation, enables a high performance panel meter to be built with the addition of only 10 passive components and a display. FEATURES *Guaranteed Zero Reading for 0V Input On All Scales *True Polarity At Zero for Precise Null Detection *1pA Typical Input Current *True Differential Input And Reference, Direct Drive LCD Display *Low Noise-Less than 15μVp-p *On chip Clock and Reference *Low Power Dissipation-Typically Less than 10mW *No Additional Active Circuits Required *Enhanced Display Stability ORDERING INFORMATION Ordering Number Lead Free Halogen Free 7106L-D40-T 7106G-D40-T 7106L-R40-R 7106G-R40-R 7106L-R40-T 7106G-R40-T 7106L-QM1-Y 7106G-QM1-Y www.unisonic.com.tw Copyright © 2011 Unisonic Technologies Co., Ltd Package Packing DIP-40 SSOP-40 SSOP-40 QFP-44 Tube Tape Reel Tube Tray 1 of 18 QW-R502-018.E 7106 CMOS IC PIN CONFIGURATION DIP- 40/SSOP-40 V+ 1 D1 2 C1 3 B1 4 A1 5 F1 6 G1 7 E1 8 , (1 s) 40 OSC 1 39 OSC 2 38 OSC 3 37 TEST 36 35 34 33 32 31 D2 9 C2 10 B2 11 A2 12 F2 13 , (10 s) 30 29 28 27 REF HI REF LO CREF + CREF COMMON IN HI IN LO A-Z BUFF INT 26 V, 25 G2(10 s) 24 C3 , 23 A3 (100 s) E2 14 D3 15 B3 16 , (100 s) F3 17 E3 18 (1000) AB4 19 22 G3 21 BP (MINUS) POL 20 MQFP - 44 NC NC TEST OSC 3 NC OSC 2 OSC 1 V+ D1 C1 B1 44 43 42 1 41 40 39 38 2 37 36 35 34 33 32 3 31 4 30 5 29 6 28 7 27 8 26 9 25 10 11 12 13 14 24 15 16 23 17 18 19 20 21 22 NC G2 C3 A3 G3 BP/GND POL AB4 E3 F3 B3 A1 F1 G1 E1 D2 C2 B2 A2 F2 E2 D3 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 18 QW-R502-018.E 7106 CMOS IC ABSOLUTE MAXIMUM RATINGS(TA=25°C) PARAMETER SYMBOL RATINGS UNIT Supply Voltage (V+ ~ V-) VDD 15 V Analog Input Voltage (Either Input) (Note 1) VI,ANG V+ ~ VV Reference Input Voltage (Either Input) VI,REF V+ ~ VV Junction Temperature TJ 150 °C Operating Temperature TOPR 0 ~ +70 °C Storage Temperature TSTG -65 ~ +150 °C Note: 1. Input voltages may exceed the supply voltages provided the input current is limited to ±100μA. 2. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER Junction to Ambient SYMBOL DIP-40 SSOP-40 QFP-44 θJA RATINGS 50 70 75 UNIT °C/W ELECTRICAL CHARACTERISTICS (TA=25℃, fCLOCK=48kHz, measured by the circuit of Fig.1) PARAMETER SYSTEM PERFORMANCE SYMBOL TEST CONDITIONS MIN TYP MAX Zero Input Reading RZ VIN=0.0V, Full Scale=200mV -000.0 ±000.0 +000.0 Ratio metric Reading RR VIN=VREF, VREF=100mV 999 999/1000 1000 ±0.2 ±1 Counts ±0.2 ±1 Counts Rollover Error ER Linearity L Common Mode Rejection Ratio CMRR Noise VN Leakage Current Input Zero Reading Drift Scale Factor Temperature Coefficient End Power Supply Character V+ Supply Current IL DZR ΦT,S COMMON Pin Analog Common Voltage VCOM Temperature Coefficient of Analog Common ΦT,A IEP -VIN=+VIN≒200mV Difference in Reading for Equal Positive and Negative Inputs Near Full Scale Full Scale=200mV or Full Scale=2V Maximum Deviation from Best Straight Line Fit (Note 2) VCM=1V,VIN=0V, Full Scale=200mV(Note 2) VIN=0V,Full Scale=200mV (Peak-To-Peak Value Not Exceeded 95% of Time) VIN=0(Note 2) VIN=0, 0℃ ~ 70℃ (Note 2) VIN=199mV, 0℃ ~ 70℃, (Ext.Ref.0ppm/℃) (Note 2) VIN=0 25kΩ Between Common and Positive Supply (With Respect to +Supply) 25kΩ Between Common and Positive Supply (With Respect to +Supply) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2.7 UNIT Digital Reading Digital Reading 50 μV/V 15 μV 1 0.2 10 1 pA μV/°C 1 5 ppm/°C 1.0 1.8 mA 3.05 3.3 V 80 ppm/°C 3 of 18 QW-R502-018.E 7106 CMOS IC ELECTRICAL CHARACTERISTICS(Cont.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT DISPLAY DRIVER Peak-to-Peak Segment Drive Voltage Peak-to-Peak Backplane Drive VD,PP V+ ~ V-=9V(Note 1) 4 5.5 6 V Voltage Note: 1. Back plane drive is in phase with segment drive for”off”segment,180 degrees out of phase for ”on” segment . Frequency is 20 times conversion rate. Average DC component is less than 50mV. 2. Not tested, guaranteed by design. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 18 QW-R502-018.E 7106 TYPICAL APPLICATIONS AND TEST CIRCUIT (LCD DISPLAY COMPONENTS SELECTED FOR 200mV FULL SCALE) - A3 23 G3 22 BP 21 20 POL C3 24 17 F3 19 AB4 V- 26 G2 25 16 B3 INT 27 15 D3 14 E2 DISPLAY 18 E3 9V C2 R2 C3 A-Z 29 C5 IN HI 31 COM 32 C1 IN LO 30 R5 CREF + 34 CREF - 33 REF LO 35 TEST 37 REF HI 36 C4 OSC 3 38 OSC 1 40 OSC 2 39 R3 R1 R4 + BUFF 28 IN 13 F2 + 12 A2 11 B2 9 D2 10 C2 8 E1 F1 7 G1 6 5 A1 3 C1 4 B1 2 D1 UTC 7106 1 V+ CMOS IC DISPLAY UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw C1=0.1μF C2=0.47μF C3=0.22μF C4=100pF C5=0.02μF R1=24kΩ R2=47kΩ R3=91kΩR 4=1kΩ R5=1MΩ 5 of 18 QW-R502-018.E 7106 CMOS IC DESIGN INFORMATION SUMMARY SHEET *OSCILLATOR FREQUENCY fosc=0.45/RC COSC>50pF, ROSC>50kΩ fOSC (Typ)=48kHz *OSCILLATOR PERIOD tOSC=RC/0.45 *INTEGRATION CLOCK FREQUENCY fCLOCK=fOSC/4 *INTEGRATION PERIOD tINT=1000×(4/fOSC) *60/50Hz REJECTION CRITERION tINT/t60Hz or tINT/t50Hz=Integer *OPTIMUM INTEGRATION CURRENT IINT=4μA *FULL SCALE ANALOG INPUT VOLTAGE VINFS (Typ)=200mV or 2V *INTEGRATE ESISTOR RINT= VINFS/ IINT *INTEGRATE CAPACITOR CINT=(tINT)(IINT)/ VINT *INTEGRATOR OUTPUT VOLTAGE SWING VINT=(tINT)(IINT)/ CINT *VINT MAXIMUM SWING (V- + 0.5V)<VINT<(V+ - 0.5V), VINT (Typ)=2V *DISPLAY COUNT COUNT=1000×VIN/VREF *CONVERSION CYCLE tCYC=tCLOCK×4000 tCYC=tOSC×16,000 When fOSC=48kHz, tCYC=333ms *COMMON MODE INPUT VOLTAGE (V- + 1V)<VIN<(V+ - 0.5V) *AUTO-ZERO CAPACITOR 0.01μF<CAZ<1μF *REFERENCE CAPACITOR 0.1μF<CREF<1μF *VCOM Biased between Vi and V*VCOM≒V+ - 2.8V Regulation lost when V+ to V- <≒6.8V If VCOM is externally pulled down to (V+ to V-)/2, the VCOM circuit will turn off. *POWER SUPPLY: SINGLE 9V V+ - V- =9V VGND≒V+ - 4.5V Digital supply is generated by internal parts. *DISPLAY: LCD Type: Direct drive with digital logic supply amplitude. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL INTEGRATOR AMPLIFIER OUTPUT WAVEFORM (INT PIN) DETAILED DESCRIPTION ANALOG SECTION Fig.1 shows the Analog Section for the UTC 7106. Each measurement cycle is divided into three phases. They are(1) auto-zero(A-Z), (2)signal integrate (INT)and (3)de-integrate(DE). AUTO-ZERO PHASE During auto-zero three things happen. First, input high and low are disconnected from the pins and internally shorted to analog COMMON. Second, the reference capacitor is charged to the reference voltage. Third, a feedback loop is closed around the system to charge the auto-zero capacitor CAZ to compensate for offset voltages in the buffer amplifier, integrator, and comparator. Since the comparator is included in the loop, the A-Z accuracy is limited only by the noise of the system. In any case, the offset referred to the input is less than 10μV. SIGNAL INTEGRATE PHASE During signal integrate, the auto-zero loop is opened, the internal short is removed, and the internal input high and low are connected to the external pins. The converter then integrates the differential voltage between IN HI and IN LO for a fixed time. This differential voltage can be within a wide common mode range: up to 1V from either supply. if, on the other hand, the input signal has no return with respect to the converter power supply, IN LO can be tied to analog COMMON to establish the correct common mode voltage. At the end of this phase, the polarity of the integrated signal is determined. DE-INTEGRATE PHASE The final phase is de-integrate, or reference integrate. Input low is internally connected to analog COMMON and input high is connected across the previously charged reference capacitor. Circuitry within the chip ensures that the capacitor will be connected with the correct polarity to cause the integrator output to return to zero. The time required for the output to return to zero is proportional to the input signal. Specifically the digital reading displayed is: DISPLAY COUNT=1000( VIN/ VREF ). DIFFERENTIAL INPUT The input can accept differential voltages anywhere within the common mode range of the input amplifier, or specifically from 0.5V below the positive supply to 1V above the negative supply. In this range, the system has a CMRR of 86dB typical. However, care must be exercised to assure the integrator output does not saturate. A worst case condition would be a large positive common mode voltage with a near full scale negative differential input voltage. The negative input signal drives the integrator positive when most of its swing has been used up by the positive common mode voltage. For these critical applications the integrator output swing can be reduced to less than the recommended 2V full scale swing with little loss of accuracy. The integrator output can swing to within 0.3V of either supply without loss of linearity. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) DIFFERENTIAL REFERENCE The reference voltage can be generated anywhere within the power supply voltage of the converter. The main source of common mode error is a roll-over voltage caused by the reference capacitor losing or gaining charge to stray capacity on its nodes. If there is a large common mode voltage, the reference capacitor can gain charge (increase voltage) when called up to de-integrate a positive signal but lose charge (decrease voltage) when called up to de-integrate a negative input signal. This difference in reference for positive or negative input voltage will give a roll-over error. However, by selecting the reference capacitor such that it is large enough in comparison to the stray capacitance, this error can be held to less than 0.5 count worst case. (See Component Value Selection) STRAY CREF CREF + V+ REF HI 34 STRAY REF LO 36 A-Z 35 A-Z CREF 33 10μ A 31 DE- INT DE+ DE+ 32 INT IN LO 29 CAZ CINT A-Z INT INTEGRATOR + 27 + TO DIGITAL SECTION A-Z 6.2V + N 1 2.8V INPUT HIGH A-Z COMMON 28 + IN HI RINT BUFFER V+ COMPARATOR DEINPUT LOW A-Z AND DE(±) 30 V- Fig.1 Analog Section UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 8 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) ANALOG COMMON This pin is included primarily to set the common mode voltage for battery operation (UTC 7106) or for any system where the input signals are floating with respect to the power supply. The COMMON pin sets a voltage that is approximately 2.8V more negative than the positive supply. This is selected to give a minimum end-of-life battery voltage of about 6V. However, analog COMMON has some of the attributes of a reference voltage. When the total supply voltage is large enough to cause the zener to regulate(>7V), the COMMON voltage will have a low voltage coefficient (0.001%/V), low output impedance (≒15Ω), and a temperature coefficient typically less than 80ppm/℃. The UTC 7106, with its negligible dissipation, suffers from none of these problems. In either case, an external reference can easily be added, as shown in Fig.2 Analog COMMON is also used as the input low return during auto-zero and de-integrate. If IN LO is different from analog COMMON, a common mode voltage exists in the system and is taken care of by the excellent CMRR of the converter. However, in some applications IN LO will be set at a fixed known voltage(power supply common for instance).In this application, analog COMMON should be tied to the same point, thus removing the common mode voltage from the converter. The same holds true for the reference voltage. If reference can be conveniently tied to analog COMMON, it should be since this removes the common mode voltage from the reference system. Within the IC, analog COMMON is tied to an N-Channel FET that can sink approximately 30mA of current to hold the voltage 2.8V below the positive supply (when a load is trying to pull the common line positive). However, there is only 10μA of source current, so COMMON may easily be tied to a more negative voltage thus overriding the internal reference. V+ V+ V V REF HI 6.8V ZENER REF LO Iz UTC 7106 UTC 7106 REF HI REF LO 6.8k 20k ICL8069 1.2V REFERENCE COMMON VFIGURE 2B. FIGURE 2 A. Fig.2 Using an External Reference UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 9 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) TEST The TEST pin serves two function. On the UTC 7106 it is coupled to the internally generated digital supply through a 500Ω resistor. Thus it can be used as the negative supply for externally generated segment drivers such as decimal points or any other presentation the user may want to include on the LCD display. Fig.3 and 4 show such an application. No more than a 1mA load should be applied. The second function is a “lamp test”. When TEST is pulled high (to V+) all segments will be turned on and the display should read ”1888”. The TEST pin will sink about 15mA under these conditions. CAUTION: In the lamp test mode, the segments have a constant DC voltage (no square-wave) . This may burn the LCD display if maintained for extended periods. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 10 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) DIGITAL SECTION Fig.5 show the digital section for the UTC 7106, respectively. In the UTC 7106, an internal digital ground is generated from a 6V Zener diode and a large P-Channel source follower. This supply is made stiff to absorb the relative large capacitive currents when the back plane(BP) voltage is switched. The BP frequency is the clock frequency divided by 800. For three readings/sec, this is a 60Hz square wave with a nominal amplitude of 5V. The segments are driven at the same frequency and amplitude and are in phase with BP when OFF, but out of phase when ON. In all cases negligible DC voltage exists across the segments. a a a b f g b e a b f g e c d b f g c d e c d BACKPLANE 21 LCD PHASE DRIVER TYPICAL SEGMENT OUTPUT V+ 7 SEGMENT DECODE 0.5mA SEGMENT OUTPUT 7 7 SEGMENT SEGMENT DECODE DECODE ÷200 LATCH 2mA , , INTERNAL DIGITAL GROUND 1000 s 100 s COUNTER COUNTER , , 10 s 1s COUNTER COUNTER TO SWITCH DRIVERS FROM COMPARATOR OUTPUT 1 CLOCK ÷4 * LOGIC CONTROL 6.2V 500Ω INTERNAL DIGITAL GROUND * THREE INVERTERS ONE INVERTER VTH=1V OSC 1 39 OSC 2 38 TEST 37 SHOWN FOR CLARITY 40 V+ 26 V- OSC 3 Fig.5 Digital Section UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 11 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) SYSTEM TIMING Fig.6 shows the clocking arrangement used in the UTC 7106. Two basic clocking arrangements can be used: 1. Fig.6A. An external oscillator connected to pin 40. 2. Fig.6B. An R-C oscillator using all three pins. The oscillator frequency is divided by four before it clocks the decade counters. It is then further divided to form the three convert-cycle phases. These are signal integrate (1000 counts), reference de-integrate (0 to 2000 counts) and auto-zero(1000 ~ 3000 counts). For signals less than full scale. auto-zero gets the unused portion of reference de-integrate. This makes a complete measure cycle of 4,000 counts (16,000 clock pulses) independent of input voltage. For three readings/second, an oscillator frequency of 48kHz would be used. To achieve maximum rejection of 60Hz pickup, the signal integrate cycle should be a multiple of 60Hz. Oscillator frequencies of 240kHz, 120kHz, 80kHz, 60kHz, 48kHz, 40kHz, 33 1/3kHz, etc. should be selected. For 50Hz rejection, Oscillator frequencies of 200kHz, 100kHz, 66 2/3kHz, 50kHz, 40kHz, etc. would be suitable. Note that 40kHz (2.5 readings/second) will reject both 50Hz and 60Hz (also 400Hz and 440Hz). INTERNAL TO PART INTERNAL TO PART ÷4 40 39 CLOCK 38 ÷4 40 39 38 R C CLOCK RC OSCILLATOR TEST FIGURE 6A FIGURE 6B Fig.6 Clock Circuits COMPONENT VALUE SELECTION Integrating Resistor Both the buffer amplifier and the integrator have a class A output stage with 100μA of quiescent current. They can supply 4μA of drive current with negligible nonlinearity. The integrating resistor should be large enough to remain in this very linear region over the input voltage range, but small enough that undue leakage requirements are not placed on the PC board. For 2V full scale, 470kΩ is near optimum and similarly a 47kΩ for a 200mV scale. Integrating Capacitor The integrating capacitor should be selected to give the maximum voltage swing that ensures tolerance buildup will not saturate the integrator swing(approximately. 0.3V from either supply).In the UTC 7106, when the analog COMMON is used as a reference, a nominaul+2V full scale integrator swing is fine. For three readings/second (48kHz clock) nominal values for CINT are 0.22μF and 0.10μF, respectively. Of course, if different oscillator frequencies are used, these values should be changed in inverse proportion to maintain the same output swing. An additional requirement of the integrating capacitor is that it must have a low dielectric absorption to prevent roll-over errors. While other types of capacitors are adequate for this application, polypropylene capacitors give undetectable errors at reasonable cost. Auto-Zero Capacitor The size of the auto-zero capacitor has some influence on the noise of the system. For 200mV full scale where noise is very important, a 0.47μF capacitor is recommended. On the 2V scale, a 0.047μF capacitor increases the speed of recovery from overload and is adequate for noise on this scale. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 12 of 18 QW-R502-018.E 7106 CMOS IC DETAILED DESCRIPTION(Cont.) Reference Capacitor A 0.1μF capacitor gives good results in most applications. However, where a large common mode voltage exists (i.e., the REF LO pin is not at analog COMMON)and a 200mV scale is used, a larger value is required to prevent roll-ovre error. Generally 1μF will hold the roll-over error to 0.5 count in this instance. Oscillator Components For all ranges of frequency a 91kΩ resistor is recommended and the capacitor is selected from the equation: f= 0.45/RC for 48kHz Clock (3 Readings/sec), C=100pF. Reference Voltage The analog input required to generate full scale output (2000 counts) is: VIN=2VREF.Thus, for the 200mV and 2V scale, VREF should equal 100mV and 1V, respectively. However, in many applications where the A/D is connected to a transducer, there will exist a scale factor other than unity between the input voltage and the digital reading. For instance, in a weighing system, the designer might like to have a full scale reading when the voltage from the transducer is 0.662V. Instead of dividing the input down to 200mV, the designer should use the input voltage directly and select VREF=0.341V. Suitable values for integrating resistor and capacitor would be 120kΩ and 0.22μF. This makes the system slightly quieter and also avoids a divider network on the input. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 13 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL APPLICATIONS The UTC 7106 may be used in a wide variety of configurations. The circuits which follow show some of the possibilities, and serve to illustrate the exceptional versatility of these A/D converters. TO PIN 1 OSC 1 40 OSC 2 39 OSC 3 38 TEST 37 REF HI 36 REF LO 35 CREF+ 34 CREF- 33 COMMON 32 IN HI 31 IN LO 30 A-Z 29 BUFF 28 INT 27 V- 26 G2 25 C3 24 A3 23 G3 22 BP 21 91kΩ SET VREF =100mV 100pF 1kΩ 22kΩ 0.1μF 1MΩ + 0. 01μF 0. 47μF 47kΩ IN + - 9V 0. 22μF TO DISPLAY TO BACKPLANE Values shown are for 200mV full scale,3 readings/sec.,floating supply voltage(9V battery). Fig.7 Using The Internal Reference UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 14 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL APPLICATIONS(Cont.) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 15 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL APPLICATIONS(Cont.) TO PIN 1 OSC1 40 91kΩ OSC2 39 OSC3 38 TEST 100pF 37 REF HI 36 REF LO 35 C REF+ 34 µ CREF- 33 0.1 F 31 IN LO 30 A-Z 29 BUFF 28 INT 27 V- 26 G2 25 C3 24 A3 G3 23 BP 21 22kΩ 100kΩ 1MΩ 100kΩ 220kΩ COMMON 32 IN HI SCALE FACTOR ADJUST ZERO ADJUST 0.01µF SILICON NPN MPS 3704 OR SIMILAR 0 . 47µ F 47 kΩ 9V 0 . 22µF TO DISPLAY 22 TO BACKPLANE A sillicon diode- connected transistor has a temperature coefficient of about -2 mV/ . Calibration is achieved by placing the sensing transistor in ice water and adjusting the . zeroing potentiometer for a 000.0 reading. The sensor should then be placed in boiling water and the scale - factor potentiometer adjusted for a 100.0 reading Fig.9 Used as A Digital Centigrade Thermometer UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 16 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL APPLICATIONS(Cont.) V+ TO LOGIC VDD 1 V+ OSC1 40 2 D1 OSC2 39 3 C1 OSC3 38 4 B1 TEST 37 5 A1 REF HI 36 6 F1 REF LO 35 7 G1 CREF+ 34 8 E1 9 O/RANGE D2 CREF- 33 COMMON TO LOGIC GND 32 10 C2 IN HI 31 11 B2 IN LO 30 12 A2 A-Z 29 13 F2 BUFF 28 14 E2 INT 27 15 D3 V- 26 16 B3 G2 25 17 F3 C3 24 18 E3 A3 23 19 AB4 G3 22 20 POL BP 21 V- U/RANGE CD4077 Fig.10 Circuit for Developing Underrange and Overrange from UTC 7106 Outputs UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 17 of 18 QW-R502-018.E 7106 CMOS IC TYPICAL APPLICATIONS(Cont.) OSC 1 40 OSC 2 39 OSC 3 38 TEST 37 REF HI 36 REF LO 35 CREF 34 CREF 33 COMMON 32 IN HI 31 IN LO 30 A-Z 29 BUFF 28 INT 27 V- 26 G2 25 C3 24 A3 23 G3 22 BP 21 TO PIN 1 91kΩ 10μF SCALE FACTOR ADJUST (VREF=100mV FOR AC TO RMS) CA3140 100pF 5μF 100kΩ + - 1kΩ 0.1μF AC IN 1N914 22kΩ 470kΩ 2.2MΩ 1μF 10kΩ 1μF 4.3kΩ 10kΩ 1μF 0.22μF 0.47μF 47kΩ + 10μF 9V - 0.22μF 100pF (FOR OPTIMUM BANDWIDTH) TO DISPLAY TO BACKPLANE Test is used as a common-mode reference level to ensure compatiblity with most op amps. Fig. 11 AC to DC Converter with UTC 7106 UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 18 of 18 QW-R502-018.E