MICROCHIP PIC16F88

PIC16F87/88
Data Sheet
18/20/28-Pin Enhanced FLASH
Microcontrollers with
nanoWatt Technology
 2003 Microchip Technology Inc.
Preliminary
DS30487B
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is intended through suggestion only
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
No representation or warranty is given and no liability is
assumed by Microchip Technology Incorporated with respect
to the accuracy or use of such information, or infringement of
patents or other intellectual property rights arising from such
use or otherwise. Use of Microchip’s products as critical
components in life support systems is not authorized except
with express written approval by Microchip. No licenses are
conveyed, implicitly or otherwise, under any intellectual
property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, MPLAB, PIC, PICmicro, PICSTART, PRO MATE and
PowerSmart are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
FilterLab, microID, MXDEV, MXLAB, PICMASTER, SEEVAL
and The Embedded Control Solutions Company are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Accuron, Application Maestro, dsPICDEM, dsPICDEM.net,
ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, InCircuit Serial Programming, ICSP, ICEPIC, microPort,
Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM,
PICC, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo,
PowerMate, PowerTool, rfLAB, rfPIC, Select Mode,
SmartSensor, SmartShunt, SmartTel and Total Endurance are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
Serialized Quick Turn Programming (SQTP) is a service mark
of Microchip Technology Incorporated in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2003, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received QS-9000 quality system
certification for its worldwide headquarters,
design and wafer fabrication facilities in
Chandler and Tempe, Arizona in July 1999
and Mountain View, California in March 2002.
The Company’s quality system processes and
procedures are QS-9000 compliant for its
PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals,
non-volatile memory and analog products. In
addition, Microchip’s quality system for the
design and manufacture of development
systems is ISO 9001 certified.
DS30487B-page ii
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18/20/28-Pin Enhanced FLASH MCUs with nanoWatt Technology
Low-Power Features:
Pin Diagram
• Power Managed modes:
- Primary RUN: RC oscillator, 76 µA, 1 MHz, 2V
- RC_RUN: 7 µA, 31.25 kHz, 2V
- SEC_RUN: 9 µA, 32 kHz, 2V
- SLEEP: 0.1 µA, 2V
• Timer1 Oscillator: 1.8 µA, 32 kHz, 2V
• Watchdog Timer: 2.2 µA, 2V
• Two-Speed Oscillator Start-up
18-Pin DIP, SOIC
RA2/AN2/CVREF/
VREFRA3/AN3/VREF+/
C1OUT
RA4/AN4/T0CKI/
C2OUT
• Three Crystal modes:
- LP, XT, HS: up to 20 MHz
• Two External RC modes
• One External Clock mode:
- ECIO: up to 20 MHz
• Internal oscillator block:
- 8 user selectable frequencies: 31 kHz,
125 kHz, 250 kHz, 500 kHz, 1 MHz, 2 MHz,
4 MHz, 8 MHz
FLASH # Single Word
(bytes) Instructions
2
17
RA0/AN0
3
16
RA7/OSC1/CLKI
15
RA6/OSC2/CLKO
14
VDD
4
VSS
5
RB0/INT/CCP1(1)
6
RB1/SDI/SDA
7
12
RB2/SDO/RX/DT
8
11
RB5/SS/TX/CK
(1)
9
10
RB4/SCK/SCL
Note 1:
13
RB7/AN6/PGD/
T1OSI
RB6/AN5/PGC/
T1OSO/T1CKI
The CCP1 pin is determined by CCPMX in
Configuration Word 1 register.
Special Microcontroller Features:
• 100,000 erase/write cycles Enhanced FLASH
program memory typical
• 1,000,000 typical erase/write cycles EEPROM
data memory typical
• EEPROM Data Retention: > 40 years
• In-Circuit Serial Programming™ (ICSP™) via two pins
• Processor read/write access to program memory
• Low-Voltage Programming
• In-Circuit Debugging via two pins
• Extended Watchdog Timer (WDT):
- Programmable period from 1 ms to 268s
• Wide operating voltage range: 2.0V to 5.5V
• Capture, Compare, PWM (CCP) module:
- Capture is 16-bit, max. resolution is 12.5 ns
- Compare is 16-bit, max. resolution is 200 ns
- PWM max. resolution is 10-bit
• 10-bit, 7-channel Analog-to-Digital Converter
• Synchronous Serial Port (SSP) with SPI™
(Master/Slave) and I2C™ (Slave)
• Addressable Universal Synchronous
Asynchronous Receiver Transmitter
(USART/SCI) with 9-bit address detection:
- RS-232 operation using internal oscillator
(no external crystal required)
• Dual Analog Comparator module:
- Programmable on-chip voltage reference
- Programmable input multiplexing from device
inputs and internal voltage reference
- Comparator outputs are externally accessible
Program Memory
RA1/AN1
RA5/MCLR/VPP
RB3/PGM/CCP1
Peripheral Features:
Device
18
PIC16F88
Oscillators:
1
Data Memory
SRAM
(bytes)
EEPROM
(bytes)
I/O
Pins
10-bit
CCP
A/D (ch) (PWM)
USART
Comparators
SSP
Timers
8/16-bit
PIC16F87
7168
4096
368
256
16
n/a
1
Y
2
Y
2/1
PIC16F88
7168
4096
368
256
16
1
1
Y
2
Y
2/1
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 1
PIC16F87/88
Pin Diagrams
18-Pin DIP, SOIC
1
18
RA1/AN1
2
17
RA0/AN0
RA4/T0CKI/C2OUT
RA5/MCLR/VPP
3
16
RA7/OSC1/CLKI
15
RA6/OSC2/CLKO
VSS
5
14
VDD
RB0/INT/CCP1(1)
6
13
RB7/PGD/T1OSI
RB1/SDI/SDA
7
12
RB6/PGC/T1OSO/T1CKI
RB2/SDO/RX/DT
8
11
RB5/SS/TX/CK
RB3/PGM/CCP1(1)
9
10
RB4/SCK/SCL
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
RA1/AN1
RA0/AN0
RA7/OSC1/CLKI
RA6/OSC2/CLKO
VDD
AVDD
RB7/PGD/T1OSI
RB6/PGC/T1OSO/T1CKI
RB5/SS/TX/CK
RB4/SCK/SCL
4
PIC16F87
RA2/AN2/CVREF
RA3/AN3/C1OUT
RA2/AN2/CVREF
RA3/AN3/C1OUT
RA4/T0CKI/C2OUT
RA5/MCLR/VPP
VSS
AVSS
RB0/INT/CCP1(1)
RB1/SDI/SDA
RB2/SDO/RX/DT
RB3/PGM/CCP1(1)
PIC16F87
20-Pin SSOP
18-Pin DIP & SOIC
1
18
RA1/AN1
2
17
RA0/AN0
RA4/AN4/T0CKI/C2OUT
RA5/MCLR/VPP
3
16
RA7/OSC1/CLKI
15
RA6/OSC2/CLKO
VSS
5
14
VDD
RB0/INT/CCP1(1)
6
13
RB7/AN6/PGD/T1OSI
RB1/SDI/SDA
7
12
RB6/AN5/PGC/T1OSO/T1CKI
RB2/SDO/RX/DT
8
11
RB5/SS/TX/CK
RB3/PGM/CCP1(1)
9
10
RB4/SCK/SCL
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
RA1/AN1
RA0/AN0
RA7/OSC1/CLKI
RA6/OSC2/CLKO
VDD
AVDD
RB7/AN6/PGD/T1OSI
RB6/AN5/PGC/T1OSO/T1CKI
RB5/SS/TX/CK
RB4/SCK/SCL
4
PIC16F88
RA2/AN2/CVREF/VREFRA3/AN3/VREF+/C1OUT
RA2/AN2/CVREF/VREFRA3/AN3/VREF+/C1OUT
RA4/AN4/T0CKI/C2OUT
RA5/MCLR1/VPP
VSS
AVSS
RB0/INT/CCP1(1)
RB1/SDI/SDA
RB2/SDO/RX/DT
RB3/PGM/CCP1(1)
Note 1:
DS30487B-page 2
PIC16F88
20-Pin SSOP
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
RA1/AN1
RA0/AN0
NC
23
22
25
24
RA2/AN2/CVREF
NC
26
RA4/T0CKI/C2OUT
RA3/AN3/C1OUT
RA5/MCLR/VPP
1
21
RA7/OSC1/CLKI
NC
VSS
2
20
RA6/OSC2/CLKO
3
19
VDD
NC
4
18
NC
AVSS
5
17
AVDD
NC
6
16
RB7/PGD/T1OSI
RB0/INT/CCP1(1)
7
15
RB6/PGC/T1OSO/T1CKI
12
13
14
RB4/SCK/SCL
RB5/SS/TX/CK
NC
RA1/AN1
NC
22
11
NC
NC
25
RA0/AN0
10
RB3/PGM/CCP1(1)
RA2/AN2/CVREF/VREF26
23
9
24
8
RB1/SDI/SDA
RB2/SDO/RX/DT
RA4/AN4/T0CKI/C2OUT
RA3/AN3/VREF+/C1OUT
27
PIC16F87
28
28-Pin QFN
Note 1:
27
28-Pin QFN
28
Pin Diagrams (Cont’d)
RA5/MCLR/VPP
1
21
RA7/OSC1/CLKI
NC
VSS
2
20
RA6/OSC2/CLKO
3
19
VDD
NC
4
18
NC
AVSS
5
17
AVDD
NC
6
16
RB7/AN6/PGD/T1OSI
RB0/INT/CCP1(1)
7
15
RB6/AN5/PGC/T1OSO/T1CKI
12
13
14
RB4/SCK/SCL
NC
11
NC
RB5/SS/TX/CK
10
9
RB3/PGM/CCP1(1)
8
RB1/SDI/SDA
RB2/SDO/RX/DT
PIC16F88
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 3
PIC16F87/88
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 5
2.0 Memory Organization ................................................................................................................................................................. 11
3.0 Data EEPROM and FLASH Program Memory ........................................................................................................................... 27
4.0 Oscillator Configurations ............................................................................................................................................................ 35
5.0 I/O Ports ..................................................................................................................................................................................... 51
6.0 Timer0 Module ........................................................................................................................................................................... 67
7.0 Timer1 Module ........................................................................................................................................................................... 71
8.0 Timer2 Module ........................................................................................................................................................................... 79
9.0 Capture/Compare/PWM (CCP) Module ..................................................................................................................................... 81
10.0 Synchronous Serial Port (SSP) Module ..................................................................................................................................... 87
11.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (USART)................................................................ 97
12.0 Analog-to-Digital Converter (A/D) Module ................................................................................................................................ 113
13.0 Comparator Module.................................................................................................................................................................. 121
14.0 Comparator Voltage Reference Module ................................................................................................................................... 127
15.0 Special Features of the CPU .................................................................................................................................................... 129
16.0 Instruction Set Summary .......................................................................................................................................................... 149
17.0 Development Support............................................................................................................................................................... 157
18.0 Electrical Characteristics .......................................................................................................................................................... 163
19.0 DC and AC Characteristics Graphs and Tables ....................................................................................................................... 191
20.0 Packaging Information.............................................................................................................................................................. 193
Appendix A: Revision History............................................................................................................................................................. 199
Appendix B: Device Differences......................................................................................................................................................... 199
Index .................................................................................................................................................................................................. 201
On-Line Support................................................................................................................................................................................. 209
Systems Information and Upgrade Hot Line ...................................................................................................................................... 209
Reader Response .............................................................................................................................................................................. 210
PIC16F87/88 Product Identification System ...................................................................................................................................... 211
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150.
We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
• The Microchip Corporate Literature Center; U.S. FAX: (480) 792-7277
When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using.
Customer Notification System
Register on our web site at www.microchip.com/cn to receive the most current information on all of our products.
DS30487B-page 4
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
1.0
DEVICE OVERVIEW
TABLE 1-1:
This document contains device specific information for
the operation of the PIC16F87/88 devices. Additional
information may be found in the PICmicro® Mid-Range
MCU Reference Manual (DS33023) which may be
downloaded from the Microchip web site. This Reference Manual should be considered a complementary
document to this data sheet, and is highly recommended reading for a better understanding of the
device architecture and operation of the peripheral
modules.
The PIC16F87/88 belongs to the Mid-Range family of
the PICmicro® devices. Block diagrams of the devices
are shown in Figure 1-1 and Figure 1-2. These devices
contain features that are new to the PIC16 product line:
• Low-power modes: RC_RUN allows the core and
peripherals to be clocked from the INTRC, while
SEC_RUN allows the core and peripherals to be
clocked from the low-power Timer1. Refer to
Section 4.7 “Power Managed Modes” for
further details.
• Internal RC oscillator with eight selectable
frequencies, including 31.25 kHz, 125 kHz,
250 kHz, 500 kHz, 1 MHz, 2 MHz, 4 MHz, and
8 MHz. The INTRC can be configured as a
primary or secondary clock source. Refer to
Section 4.5 “Internal Oscillator Block” for
further details.
• The Timer1 module current consumption has
been greatly reduced from 20 µA (previous PIC16
devices) to 1.8 µA typical (32 kHz at 2V), which is
ideal for real-time clock applications. Refer to
Section 7.0 “Timer1 Module” for further details.
• Extended Watchdog Timer (WDT) that can have a
programmable period from 1 ms to 268s. The
WDT has its own 16-bit prescaler. Refer to
Section 15.12 “Watchdog Timer (WDT)” for
further details.
• Two-Speed Start-up: When the oscillator is
configured for LP, XT, or HS, this feature will clock
the device from the INTRC while the oscillator is
warming up. This, in turn, will enable almost
immediate code execution. Refer to
Section 15.12.3 “Two-Speed Clock Start-up
Mode” for further details.
• Fail-Safe Clock Monitor: This feature will allow the
device to continue operation if the primary or
secondary clock source fails by switching over to
the INTRC.
• The A/D module has a new register for PIC16
devices named ANSEL. This register allows
easier configuration of analog or digital I/O pins.
 2003 Microchip Technology Inc.
AVAILABLE MEMORY IN
PIC16F87/88 DEVICES
Device
Program
FLASH
Data
Memory
Data
EEPROM
PIC16F87/88
4K x 14
368 x 8
256 x 8
There are 16 I/O pins that are user configurable on a
pin-to-pin basis. Some pins are multiplexed with other
device functions. These functions include:
•
•
•
•
•
•
•
•
•
•
External Interrupt
Change on PORTB Interrupt
Timer0 Clock Input
Low-power Timer1 Clock/Oscillator
Capture/Compare/PWM
10-bit, 7-channel A/D Converter (PIC16F88 only)
SPI™/I2C™
Two Analog Comparators
USART
MCLR (RA5) can be configured as an Input
Table 1-2 details the pinout of the device with
descriptions and details for each pin.
Preliminary
DS30487B-page 5
PIC16F87/88
FIGURE 1-1:
PIC16F87 DEVICE BLOCK DIAGRAM
13
Program
Memory
Program
Bus
14
RAM Addr(1)
RA0/AN0
RA1/AN1
RA2/AN2/CVREF
RA3/AN3/C1OUT
RA4/T0CKI/C2OUT
RA5/MCLR/VPP
RA6/OSC2/CLKO
RA7/OSC1/CLKI
9
PORTB
Addr MUX
Instruction reg
7
Direct Addr
PORTA
RAM
File
Registers
368 x 8
8 Level Stack
(13-bit)
4K x 14
8
Data Bus
Program Counter
FLASH
8
Indirect
Addr
FSR reg
STATUS reg
8
3
Power-up
Timer
Instruction
Decode &
Control
Timing
Generation
OSC1/CLKI
OSC2/CLKO
Oscillator
Start-up Timer
Note 1:
2:
MUX
ALU
Power-on
Reset
8
Watchdog
Timer
Brown-out
Reset
RA5/MCLR
RB0/INT/CCP1(2)
RB1/SDI/SDA
RB2/SDO/RX/DT
RB3/PGM/CCP1(2)
RB4/SCK/SCL
RB5/SS/TX/CK
RB6/PGC/T1OSO/T1CKI
RB7/PGD/T1OSI
W reg
VDD, VSS
Timer2
Timer1
Timer0
SSP
USART
CCP1
Data EE
256 Bytes
Comparators
Higher order bits are from the STATUS register.
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
DS30487B-page 6
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 1-2:
PIC16F88 DEVICE BLOCK DIAGRAM
13
Program
Memory
Program
Bus
14
RAM Addr(1)
RA0/AN0
RA1/AN1
RA2/AN2/CVREF/VREFRA3/AN3/VREF+/C1OUT
RA4/AN4/T0CKI/C2OUT
RA5/MCLR/VPP
RA6/OSC2/CLKO
RA7/OSC1/CLKI
9
PORTB
Addr MUX
Instruction reg
7
Direct Addr
PORTA
RAM
File
Registers
368 x 8
8 Level Stack
(13-bit)
4K x 14
8
Data Bus
Program Counter
FLASH
8
RB0/INT/CCP1(2)
RB1/SDI/SDA
RB2/SDO/RX/DT
RB3/PGM/CCP1(2)
RB4/SCK/SCL
RB5/SS/TX/CK
RB6/AN5/PGC/T1OSO/T1CKI
RB7/AN6/PGD/T1OSI
Indirect
Addr
FSR reg
STATUS reg
8
3
Power-up
Timer
Oscillator
Start-up Timer
Instruction
Decode &
Control
8
Watchdog
Timer
Brown-out
Reset
OSC1/CLKI
OSC2/CLKO
RA5/MCLR
Note 1:
2:
ALU
Power-on
Reset
Timing
Generation
MUX
W reg
VDD, VSS
Timer2
Timer1
Timer0
10-bit A/D
USART
CCP1
Data EE
256 Bytes
Comparators
SSP
Higher order bits are from the STATUS register.
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 7
PIC16F87/88
TABLE 1-2:
PIC16F87/88 PINOUT DESCRIPTION
PDIP/
SOIC
Pin#
SSOP
Pin#
QFN
Pin#
RA0/AN0
RA0
AN0
17
19
23
RA1/AN1
RA1
AN1
18
RA2/AN2/CVREF/VREFRA2
AN2
CVREF
VREF-(4)
1
RA3/AN3/VREF+/C1OUT
RA3
AN3
VREF+(4)
C1OUT
2
RA4/AN4/T0CKI/C2OUT
RA4
AN4(4)
T0CKI
C2OUT
3
RA5/MCLR/VPP
RA5
MCLR
4
Pin Name
I/O/P
Type
Buffer
Type
Description
PORTA is a bidirectional I/O port.
20
1
2
3
4
15
17
Legend:
Note 1:
2:
3:
4:
5:
16
18
Bidirectional I/O pin.
Analog input channel 0.
I/O
I
TTL
Analog
Bidirectional I/O pin.
Analog input channel 1.
I/O
I
O
I
TTL
Analog
Bidirectional I/O pin.
Analog input channel 2.
Comparator VREF output.
A/D reference voltage (Low) input.
I/O
I
I
O
TTL
Analog
Analog
Bidirectional I/O pin.
Analog input channel 3.
A/D reference voltage (High) input.
Comparator 1 output.
I/O
I
I
O
ST
Analog
ST
Bidirectional I/O pin.
Analog input channel 4.
Clock input to the TMR0 timer/counter.
Comparator 2 output.
I
I
ST
ST
P
–
I/O
O
ST
–
O
–
I/O
I
I
ST
ST/CMOS(3)
–
26
Analog
27
28
1
Input pin.
Master Clear (Reset). Input/programming voltage
input. This pin is an active low RESET to the device.
Programming voltage input.
20
CLKO
RA7/OSC1/CLKI
RA7
OSC1
CLKI
TTL
Analog
24
VPP
RA6/OSC2/CLKO
RA6
OSC2
I/O
I
Bidirectional I/O pin.
Oscillator crystal output. Connects to crystal or
resonator in Crystal Oscillator mode.
In RC mode, this pin outputs CLKO signal which has
1/4 the frequency of OSC1 and denotes the
instruction cycle rate.
21
Bidirectional I/O pin.
Oscillator crystal input.
External clock source input.
I = Input
O
= Output
I/O = Input/Output
P = Power
– = Not used
TTL = TTL Input
ST = Schmitt Trigger Input
This buffer is a Schmitt Trigger input when configured as the external interrupt.
This buffer is a Schmitt Trigger input when used in Serial Programming mode.
This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.
PIC16F88 devices only.
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
DS30487B-page 8
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 1-2:
PIC16F87/88 PINOUT DESCRIPTION (CONTINUED)
Pin Name
PDIP/
SOIC
Pin#
SSOP
Pin#
QFN
Pin#
I/O/P
Type
Buffer
Type
Description
PORTB is a bidirectional I/O port. PORTB can be
software programmed for internal weak pull-up on all
inputs.
RB0/INT/CCP1(5)
RB0
INT
CCP1
6
RB1/SDI/SDA
RB1
SDI
SDA
7
RB2/SDO/RX/DT
RB2
SDO
RX
DT
8
RB3/PGM/CCP1(5)
RB3
PGM
CCP1
9
RB4/SCK/SCL
RB4
SCK
SCL
10
RB5/SS/TX/CK
RB5
SS
TX
CK
11
RB6/AN5/PGC/T1OSO/
T1CKI
RB6
AN5(4)
PGC
T1OSO
T1CKI
12
RB7/AN6/PGD/T1OSI
RB7
AN6(4)
PGD
T1OSI
13
VSS
5
14
Note 1:
2:
3:
4:
5:
8
9
10
11
12
13
14
7
I/O
I
I/O
TTL
ST(1)
ST
Bidirectional I/O pin.
External interrupt pin.
Capture input, Compare output, PWM output.
I/O
I
I/O
TTL
ST
ST
Bidirectional I/O pin.
SPI Data in.
I2C Data.
I/O
O
I
I/O
TTL
ST
Bidirectional I/O pin.
SPI Data out.
USART asynchronous receive.
USART synchronous detect.
I/O
I/O
I
TTL
ST
ST
Bidirectional I/O pin.
Low-Voltage ICSP programming enable pin.
Capture input, Compare output, PWM output.
I/O
I/O
I
TTL
ST
ST
Bidirectional I/O pin. Interrupt-on-change pin.
Synchronous serial clock input/output for SPI.
Synchronous serial clock Input for I2C.
I/O
I
O
I/O
TTL
TTL
Bidirectional I/O pin. Interrupt-on-change pin.
Slave select for SPI in Slave mode.
USART asynchronous transmit.
USART synchronous clock.
I/O
I
I/O
O
I
TTL
Bidirectional I/O pin. Interrupt-on-change pin.
Analog input channel 5.
In-circuit debugger and programming clock pin.
Timer1 oscillator output.
Timer1 external clock input.
8
9
10
12
13
15
5, 6
ST(2)
ST
ST
16
I/O
I
I
I
VDD
Legend:
7
3, 5
15, 16 17, 19
Bidirectional I/O pin. Interrupt-on-change pin.
Analog input channel 6.
In-circuit debugger and ICSP programming data pin.
Timer1 oscillator input.
TTL
ST(2)
ST
P
–
Ground reference for logic and I/O pins.
P
–
Positive supply for logic and I/O pins.
I = Input
O
= Output
I/O = Input/Output
P = Power
– = Not used
TTL = TTL Input
ST = Schmitt Trigger Input
This buffer is a Schmitt Trigger input when configured as the external interrupt.
This buffer is a Schmitt Trigger input when used in Serial Programming mode.
This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.
PIC16F88 devices only.
The CCP1 pin is determined by CCPMX in Configuration Word 1 register.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 9
PIC16F87/88
NOTES:
DS30487B-page 10
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
2.0
MEMORY ORGANIZATION
FIGURE 2-1:
There are two memory blocks in the PIC16F87/88
devices. These are the program memory and the data
memory. Each block has its own bus so access to each
block can occur during the same oscillator cycle.
PC<12:0>
CALL, RETURN
RETFIE, RETLW
The data memory can be further broken down into the
general purpose RAM and the Special Function
Registers (SFRs). The operation of the SFRs that
control the “core” are described here. The SFRs used
to control the peripheral modules are described in the
section discussing each individual peripheral module.
The data memory area also contains the data EEPROM
memory. This memory is not directly mapped into the
data memory but is indirectly mapped. That is, an indirect address pointer specifies the address of the data
EEPROM memory to read/write. The PIC16F87/88
device’s 256 bytes of data EEPROM memory have the
address range 00h-FFh. More details on the EEPROM
memory can be found in Section 3.0 “Data EEPROM
and FLASH Program Memory”.
Additional information on device memory may be found
in the PICmicro® Mid-Range Reference Manual
(DS33023).
2.1
PROGRAM MEMORY MAP
AND STACK: PIC16F87/88
13
Stack Level 1
Stack Level 2
Stack Level 8
On-chip
Program
Memory
RESET Vector
0000h
Interrupt Vector
0004h
0005h
Page 0
07FFh
0800h
Page 1
0FFFh
1000h
Program Memory Organization
The PIC16F87/88 devices have a 13-bit program
counter capable of addressing an 8K x 14 program
memory space. For the PIC16F87/88, the first 4K x 14
(0000h-0FFFh) is physically implemented (see
Figure 2-1). Accessing a location above the physically
implemented address will cause a wraparound. For
example, the same instruction will be accessed at locations 020h, 420h, 820h, C20h, 1020h, 1420h, 1820h,
and 1C20h.
The RESET vector is at 0000h and the interrupt vector
is at 0004h.
Wraps to
0000h - 03FFh
1FFFh
2.2
Data Memory Organization
The Data Memory is partitioned into multiple banks that
contain the General Purpose Registers and the Special
Function Registers. Bits RP1 (STATUS<6>) and RP0
(STATUS<5>) are the bank select bits.
RP1:RP0
Bank
00
0
01
1
10
2
11
3
Each bank extends up to 7Fh (128 bytes). The lower
locations of each bank are reserved for the Special
Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as
static RAM. All implemented banks contain SFRs.
Some “high use” SFRs from one bank may be mirrored
in another bank for code reduction and quicker access
(e.g., the STATUS register is in Banks 0-3).
Note:
 2003 Microchip Technology Inc.
Preliminary
EEPROM data memory description can be
found in Section 3.0 “Data EEPROM and
FLASH Program Memory” of this data
sheet.
DS30487B-page 11
PIC16F87/88
2.2.1
GENERAL PURPOSE REGISTER FILE
The register file can be accessed either directly, or
indirectly through the File Select Register (FSR).
FIGURE 2-2:
PIC16F87 REGISTER FILE MAP
Indirect addr.(*)
TMR0
PCL
STATUS
FSR
PORTA
PORTB
PCLATH
INTCON
PIR1
PIR2
TMR1L
TMR1H
T1CON
TMR2
T2CON
SSPBUF
SSPCON1
CCPR1L
CCPR1H
CCP1CON
RCSTA
TXREG
RCREG
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
Indirect addr.(*)
OPTION
PCL
STATUS
FSR
TRISA
TRISB
PCLATH
INTCON
PIE1
PIE2
PCON
OSCCON
OSCTUNE
PR2
SSPADD
SSPSTAT
TXSTA
SPBRG
CMCON
CVRCON
1Eh
1Fh
20h
General
Purpose
Register
80 Bytes
General
Purpose
Register
96 Bytes
accesses
70h-7Fh
7Fh
Bank 0
*
Note 1:
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
A0h
EFh
F0h
FFh
Bank 1
File
Address
File
Address
File
Address
File
Address
Indirect addr.(*)
TMR0
PCL
STATUS
FSR
WDTCON
PORTB
PCLATH
INTCON
EEDATA
EEADR
EEDATH
EEADRH
100h
101h
102h
103h
104h
105h
106h
107h
108h
109h
10Ah
10Bh
10Ch
10Dh
10Eh
10Fh
110h
Indirect addr.(*)
OPTION
PCL
STATUS
FSR
TRISB
PCLATH
INTCON
EECON1
EECON2
Reserved(1)
Reserved(1)
General
Purpose
Register
16 Bytes
General
Purpose
Register
16 Bytes
19Fh
1A0h
11Fh
120h
General
Purpose
Register
80 Bytes
accesses
70h-7Fh
General
Purpose
Register
80 Bytes
16Fh
170h
accesses
70h - 7Fh
17Fh
Bank 2
180h
181h
182h
183h
184h
185h
186h
187h
188h
189h
18Ah
18Bh
18Ch
18Dh
18Eh
18Fh
190h
1EFh
1F0h
1FFh
Bank 3
Unimplemented data memory locations, read as ‘0’.
Not a physical register.
This register is reserved, maintain this register clear.
DS30487B-page 12
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 2-3:
PIC16F88 REGISTER FILE MAP
File
Address
File
Address
Indirect addr.(*)
TMR0
PCL
STATUS
FSR
PORTA
PORTB
PCLATH
INTCON
PIR1
PIR2
TMR1L
TMR1H
T1CON
TMR2
T2CON
SSPBUF
SSPCON1
CCPR1L
CCPR1H
CCP1CON
RCSTA
TXREG
RCREG
ADRESH
ADCON0
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
Indirect addr.(*)
OPTION
PCL
STATUS
FSR
TRISA
TRISB
PCLATH
INTCON
PIE1
PIE2
PCON
OSCCON
OSCTUNE
PR2
SSPADD
SSPSTAT
TXSTA
SPBRG
ANSEL
CMCON
CVRCON
ADRESL
ADCON1
General
Purpose
Register
80 Bytes
General
Purpose
Register
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
A0h
7Fh
Bank 0
Note 1:
FFh
Bank 1
Indirect addr.(*)
OPTION
PCL
STATUS
FSR
TRISB
PCLATH
INTCON
EECON1
EECON2
Reserved(1)
Reserved(1)
19Fh
1A0h
11Fh
120h
General
Purpose
Register
80 Bytes
General
Purpose
Register
80 Bytes
16Fh
170h
1EFh
1F0h
accesses
70h - 7Fh
17Fh
Bank 2
180h
181h
182h
183h
184h
185h
186h
187h
188h
189h
18Ah
18Bh
18Ch
18Dh
18Eh
18Fh
190h
General
Purpose
Register
16 Bytes
General
Purpose
Register
16 Bytes
accesses
70h-7Fh
accesses
70h-7Fh
*
Indirect addr.(*) 100h
101h
TMR0
102h
PCL
103h
STATUS
104h
FSR
WDTCON
105h
106h
PORTB
107h
108h
109h
10Ah
PCLATH
10Bh
INTCON
10Ch
EEDATA
EEADR
10Dh
10Eh
EEDATH
10Fh
EEADRH
110h
EFh
F0h
96 Bytes
File
Address
File
Address
1FFh
Bank 3
Unimplemented data memory locations, read as ‘0’.
Not a physical register.
This register is reserved, maintain this register clear.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 13
PIC16F87/88
2.2.2
SPECIAL FUNCTION REGISTERS
The Special Function Registers are registers used by
the CPU and peripheral modules for controlling the
desired operation of the device. These registers are
implemented as static RAM. A list of these registers is
given in Table 2-1.
TABLE 2-1:
Address
Name
The Special Function Registers can be classified into
two sets: core (CPU) and peripheral. Those registers
associated with the core functions are described in
detail in this section. Those related to the operation of
the peripheral features are described in detail in the
peripheral feature section.
SPECIAL FUNCTION REGISTER SUMMARY
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Details
on
page
Bank 0
00h(2)
INDF
Addressing this location uses contents of FSR to address data memory
(not a physical register)
0000 0000
26, 135
01h
TMR0
Timer0 Module Register
xxxx xxxx
69
02h(2)
PCL
Program Counter (PC) Least Significant Byte
0000 0000
03h(2)
STATUS
0001 1xxx
17
04h(2)
FSR
Indirect Data Memory Address Pointer
xxxx xxxx
135
05h
PORTA
PORTA Data Latch when written; PORTA pins when read (PIC16F87)
PORTA Data Latch when written; PORTA pins when read (PIC16F88)
xxxx 0000
xxx0 0000
52
06h
PORTB
PORTB Data Latch when written; PORTB pins when read (PIC16F87)
PORTB Data Latch when written; PORTB pins when read (PIC16F88)
xxxx xxxx
00xx xxxx
58
07h
—
Unimplemented
—
—
08h
—
Unimplemented
—
—
09h
—
Unimplemented
—
—
---0 0000
135
0000 000x
19, 69,
77
IRP
RP1
RP0
0Ah(1,2)
PCLATH
—
—
—
0Bh(2)
INTCON
GIE
PEIE
TMR0IE
0Ch
PIR1
—
ADIF
0Dh
PIR2
OSFIF
CMIF
0Eh
TMR1L
0Fh
TMR1H
10h
T1CON
11h
TMR2
12h
T2CON
13h
SSPBUF
14h
SSPCON
15h
CCPR1L
16h
CCPR1H
17h
CCP1CON
18h
RCSTA
19h
TXREG
1Ah
RCREG
1Bh
—
1Ch
1Dh
DC
C
Write Buffer for the upper 5 bits of the Program Counter
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
-000 0000
21, 77
—
EEIF
—
—
—
—
00-0 ----
23, 34
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
xxxx xxxx
77, 83
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
xxxx xxxx
77, 83
72, 83
—
T1RUN
T1CKPS1
T1CKPS0
T1OSCEN
T1SYNC
TMR1CS
TMR1ON
-000 0000
0000 0000
80, 85
TOUTPS2
TOUTPS1
TOUTPS0
TMR2ON
T2CKPS1
T2CKPS0
-000 0000
80, 85
xxxx xxxx
90, 95
SSPM2
SSPM1
SSPM0
0000 0000
89, 95
Capture/Compare/PWM Register 1 (LSB)
xxxx xxxx
83, 85
Capture/Compare/PWM Register 1 (MSB)
xxxx xxxx
83, 85
Timer2 Module Register
—
TOUTPS3
Synchronous Serial Port Receive Buffer/Transmit Register
WCOL
SSPOV
SSPEN
CKP
SSPM3
CCP1X
CCP1Y
CCP1M3
CCP1M2
CCP1M1
CCP1M0
--00 0000
81, 83
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
0000 000x
98, 99
USART Transmit Data Register
0000 0000
103
USART Receive Data Register
0000 0000
105
Unimplemented
—
—
—
Unimplemented
—
—
—
Unimplemented
—
—
xxxx xxxx
120
0000 00-0
114, 120
1Fh
ADCON0(4)
2:
3:
4:
Z
—
ADRESH(4)
Note 1:
PD
—
1Eh
Legend:
TO
A/D Result Register High Byte
ADCS1
ADCS0
CHS2
CHS1
CHS0
GO/DONE
—
ADON
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as ‘0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8>, whose
contents are transferred to the upper byte of the program counter.
These registers can be addressed from any bank.
RA5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
PIC16F88 device only.
DS30487B-page 14
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 2-1:
Address
Name
SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Details
on
page
0000 0000
26, 135
1111 1111
18, 69
0000 0000
135
Bank 1
80h(2)
INDF
81h
OPTION
82h(2)
PCL
83h(2)
STATUS
84h(2)
FSR
85h
TRISA
86h
TRISB
Addressing this location uses contents of FSR to address data memory
(not a physical register)
RBPU
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
Program Counter (PC) Least Significant Byte
IRP
RP1
RP0
TO
PD
Z
DC
C
Indirect Data Memory Address Pointer
TRISA7
TRISA6
TRISA5(3) PORTA Data Direction Register (TRISA<4:0>)
PORTB Data Direction Register
0001 1xxx
17
xxxx xxxx
135
1111 1111
52, 126
1111 1111
58, 85
87h
—
Unimplemented
—
—
88h
—
Unimplemented
—
—
89h
—
Unimplemented
—
—
---0 0000
135
0000 000x
19, 69,
77
8Ah(1,2)
PCLATH
—
—
—
8Bh(2)
INTCON
GIE
PEIE
TMR0IE
8Ch
PIE1
—
ADIE
8Dh
PIE2
OSFIE
CMIE
8Eh
PCON
—
—
—
—
—
—
8Fh
OSCCON
—
IRCF2
IRCF1
IRCF0
OSTS
IOFS
90h
OSCTUNE
—
—
TUN5
TUN4
TUN3
TUN2
TUN1
91h
—
Write Buffer for the upper 5 bits of the Program Counter
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
-000 0000
20, 80
—
EEIE
—
—
—
—
00-0 ----
22, 34
POR
BOR
---- --qq
24
SCS1
SCS0
-000 0000
40
TUN0
--00 0000
38
Unimplemented
92h
PR2
Timer2 Period Register
93h
SSPADD
Synchronous Serial Port (I2C mode) Address Register
94h
SSPSTAT
SMP
CKE
D/A
P
S
R/W
UA
BF
—
—
1111 1111
80, 85
0000 0000
95
0000 0000
88, 95
95h
—
Unimplemented
—
—
96h
—
Unimplemented
—
—
97h
—
Unimplemented
—
—
98h
TXSTA
0000 -010
97, 99
99h
SPBRG
0000 0000
99, 103
9Ah
—
—
120
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
Baud Rate Generator Register
Unimplemented
9Bh
ANSEL(4)
—
ANS6
ANS5
ANS4
ANS3
ANS2
ANS1
ANS0
-111 1111
120
9Ch
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
0000 0111
121,
126, 128
9Dh
CVRCON
CVREN
CVROE
CVRR
—
CVR3
CVR2
CVR1
CVR0
000- 0000 126, 128
9Eh
ADRESL(4)
9Fh
ADCON1(4)
VCFG0
—
—
—
—
Legend:
Note 1:
2:
3:
4:
A/D Result Register Low Byte
ADFM
ADCS2
VCFG1
xxxx xxxx
120
0000 ----
52, 115,
120
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as ‘0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8>, whose
contents are transferred to the upper byte of the program counter.
These registers can be addressed from any bank.
RA5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
PIC16F88 device only.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 15
PIC16F87/88
TABLE 2-1:
Address
Name
SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Details
on
page
26, 135
Bank 2
100h(2)
INDF
Addressing this location uses contents of FSR to address data memory
(not a physical register)
0000 0000
101h
TMR0
Timer0 Module Register
xxxx xxxx
69
102h(2)
PCL
Program Counter's (PC) Least Significant Byte
0000 0000
135
103h(2)
STATUS
(2)
104h
FSR
105h
WDTCON
106h
PORTB
107h
—
108h
109h
IRP
RP1
RP0
TO
PD
Z
DC
C
Indirect Data Memory Address Pointer
142
58
Unimplemented
—
—
—
Unimplemented
—
—
—
Unimplemented
—
—
---0 0000
135
0000 000x
19, 69,
77
10Ah(1,2) PCLATH
—
WDTPS1
WDTPS0
SWDTEN
xxxx xxxx
---0 1000
—
WDTPS2
17
135
xxxx xxxx
—
WDTPS3
0001 1xxx
PORTB Data Latch when written; PORTB pins when read
—
—
—
GIE
PEIE
TMR0IE
Write Buffer for the upper 5 bits of the Program Counter
10Bh(2)
INTCON
10Ch
EEDATA
EEPROM Data Register Low Byte
xxxx xxxx
34
10Dh
EEADR
EEPROM Address Register Low Byte
xxxx xxxx
34
10Eh
EEDATH
—
—
10Fh
EEADRH
—
—
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
EEPROM Data Register High Byte
—
—
EEPROM Address Register High Byte
--xx xxxx
34
---- xxxx
34
0000 0000
135
1111 1111
18, 69
0000 0000
135
Bank 3
180h(2)
INDF
181h
OPTION
182h(2)
PCL
(2)
183h
Addressing this location uses contents of FSR to address data memory
(not a physical register)
STATUS
(2)
184h
FSR
185h
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
IRP
RP1
RP0
TO
PD
Z
DC
C
Indirect Data Memory Address Pointer
—
186h
RBPU
Program Counter (PC) Least Significant Byte
TRISB
Unimplemented
PORTB Data Direction Register
0001 1xxx
17
xxxx xxxx
135
—
—
1111 1111
58, 83
187h
—
Unimplemented
—
—
188h
—
Unimplemented
—
—
189h
—
Unimplemented
—
—
---0 0000
135
18Ah(1,2) PCLATH
18Bh(2)
INTCON
18Ch
EECON1
18Dh
EECON2
—
—
—
Write Buffer for the upper 5 bits of the Program Counter
GIE
PEIE
TMR0IE
INT0IE
RBIE
TMR0IF
INT0IF
RBIF
0000 000x
19, 69,
77
EEPGD
—
—
FREE
WRERR
WREN
WR
RD
x--x x000
28, 34
EEPROM Control Register2 (not a physical register)
---- ----
34
18Eh
—
Reserved, maintain clear
0000 0000
—
18Fh
—
Reserved, maintain clear
0000 0000
—
Legend:
Note 1:
2:
3:
4:
x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as ‘0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8>, whose
contents are transferred to the upper byte of the program counter.
These registers can be addressed from any bank.
RA5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
PIC16F88 device only.
DS30487B-page 16
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
2.2.2.1
STATUS Register
The STATUS register, shown in Register 2-1, contains
the arithmetic status of the ALU, the RESET status and
the bank select bits for data memory.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
REGISTER 2-1:
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register because these instructions do not
affect the Z, C or DC bits from the STATUS register. For
other instructions not affecting any status bits, see
Section 16.0 “Instruction Set Summary”.
Note:
The C and DC bits operate as a borrow
and digit borrow bit, respectively, in subtraction. See the SUBLW and SUBWF
instructions for examples.
STATUS REGISTER (ADDRESS 03h, 83h, 103h, 183h)
R/W-0
R/W-0
R/W-0
R-1
R-1
R/W-x
R/W-x
R/W-x
IRP
RP1
RP0
TO
PD
Z
DC
C
bit 7
bit 0
bit 7
IRP: Register Bank Select bit (used for indirect addressing)
1 = Bank 2, 3 (100h - 1FFh)
0 = Bank 0, 1 (00h - FFh)
bit 6-5
RP<1:0>: Register Bank Select bits (used for direct addressing)
11 = Bank 3 (180h - 1FFh)
10 = Bank 2 (100h - 17Fh)
01 = Bank 1 (80h - FFh)
00 = Bank 0 (00h - 7Fh)
Each bank is 128 bytes.
bit 4
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
bit 3
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
bit 2
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1
DC: Digit carry/borrow bit (ADDWF, ADDLW, SUBLW and SUBWF instructions)(1)
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
bit 0
C: Carry/borrow bit (ADDWF, ADDLW, SUBLW and SUBWF instructions)(1,2)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1:
2:
For borrow, the polarity is reversed. A subtraction is executed by adding the two’s
complement of the second operand.
For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order
bit of the source register.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 17
PIC16F87/88
2.2.2.2
OPTION Register
Note:
The OPTION register is a readable and writable register that contains various control bits to configure the
TMR0 prescaler/WDT postscaler (single assignable
register known also as the prescaler), the external INT
interrupt, TMR0, and the weak pull-ups on PORTB.
REGISTER 2-2:
To achieve a 1:1 prescaler assignment for
the TMR0 register, assign the prescaler to
the Watchdog Timer. Although the prescaler can be assigned to either the WDT or
Timer0, but not both, a new divide counter
is implemented in the WDT circuit to give
multiple WDT time-out selection. This
allows TMR0 and WDT to each have their
own scaler. Refer to Section 15.12
“Watchdog Timer (WDT)” for further
details.
OPTION REGISTER (ADDRESS 81h, 181h)
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
RBPU
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
bit 7
bit 0
bit 7
RBPU: PORTB Pull-up Enable bit
1 = PORTB pull-ups are disabled
0 = PORTB pull-ups are enabled by individual port latch values
bit 6
INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of RB0/INT pin
0 = Interrupt on falling edge of RB0/INT pin
bit 5
T0CS: TMR0 Clock Source Select bit
1 = Transition on RA4/T0CKI pin
0 = Internal instruction cycle clock (CLKO)
bit 4
T0SE: TMR0 Source Edge Select bit
1 = Increment on high-to-low transition on RA4/T0CKI pin
0 = Increment on low-to-high transition on RA4/T0CKI pin
bit 3
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
bit 2-0
PS<2:0>: Prescaler Rate Select bits
Bit Value
000
001
010
011
100
101
110
111
TMR0 Rate WDT Rate
1:2
1:4
1:8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
1:1
1:2
1:4
1:8
1 : 16
1 : 32
1 : 64
1 : 128
Legend:
DS30487B-page 18
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
2.2.2.3
INTCON Register
The INTCON register is a readable and writable register that contains various enable and flag bits for the
TMR0 register overflow, RB Port change and External
RB0/INT pin interrupts.
REGISTER 2-3:
Note:
Interrupt flag bits get set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt.
INTCON: INTERRUPT CONTROL REGISTER (ADDRESS 0Bh, 8Bh, 10Bh, 18Bh)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-x
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
bit 7
bit 0
bit 7
GIE: Global Interrupt Enable bit
1 = Enables all unmasked interrupts
0 = Disables all interrupts
bit 6
PEIE: Peripheral Interrupt Enable bit
1 = Enables all unmasked peripheral interrupts
0 = Disables all peripheral interrupts
bit 5
TMR0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 interrupt
0 = Disables the TMR0 interrupt
bit 4
INTE: RB0/INT External Interrupt Enable bit
1 = Enables the RB0/INT external interrupt
0 = Disables the RB0/INT external interrupt
bit 3
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
bit 2
TMR0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed (must be cleared in software)
0 = TMR0 register did not overflow
bit 1
INTF: RB0/INT External Interrupt Flag bit
1 = The RB0/INT external interrupt occurred (must be cleared in software)
0 = The RB0/INT external interrupt did not occur
bit 0
RBIF: RB Port Change Interrupt Flag bit
A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch
condition and allow flag bit RBIF to be cleared.
1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)
0 = None of the RB7:RB4 pins have changed state
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 19
PIC16F87/88
2.2.2.4
PIE1 Register
This register contains the individual enable bits for the
peripheral interrupts.
Note:
Bit PEIE (INTCON<6>) must be set to
enable any peripheral interrupt.
REGISTER 2-4:
PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1 (ADDRESS 8Ch)
U-0
—
bit 7
R/W-0
ADIE(1)
R/W-0
RCIE
R/W-0
TXIE
bit 7
Unimplemented: Read as ‘0’
bit 6
ADIE: A/D Converter Interrupt Enable bit(1)
1 = Enabled
0 = Disabled
R/W-0
SSPIE
R/W-0
CCP1IE
R/W-0
TMR2IE
R/W-0
TMR1IE
bit 0
Note 1: This bit is only implemented on the PIC16F88. The bit will read ‘0’ on the PIC16F87.
bit 5
RCIE: USART Receive Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 4
TXIE: USART Transmit Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 3
SSPIE: Synchronous Serial Port (SSP) Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 2
CCP1IE: CCP1 Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 1
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 0
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enabled
0 = Disabled
Legend:
DS30487B-page 20
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
2.2.2.5
PIR1 Register
This register contains the individual flag bits for the
peripheral interrupts.
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit, or the global
enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt.
REGISTER 2-5:
PIR1: PERIPHERAL INTERRUPT STATUS REGISTER 1 (ADDRESS 0Ch)
U-0
—
bit 7
R/W-0
ADIF(1)
R-0
RCIF
R-0
TXIF
R-0
SSPIF
R/W-0
CCP1IF
bit 7
Unimplemented: Read as ‘0’
bit 6
ADIF: A/D Converter Interrupt Flag bit(1)
1 = The A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
R/W-0
TMR2IF
R/W-0
TMR1IF
bit 0
Note 1: This bit is only implemented on the PIC16F88. The bit will read ‘0’ on the PIC16F87.
bit 5
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (cleared by reading RCREG)
0 = The USART receive buffer is not full
bit 4
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (cleared by writing to TXREG)
0 = The USART transmit buffer is full
bit 3
SSPIF: Synchronous Serial Port (SSP) Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
bit 1
TMR2IF: TMR2 to PR2 Interrupt Flag bit
1 = A TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
bit 0
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = The TMR1 register overflowed (must be cleared in software)
0 = The TMR1 register did not overflow
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 21
PIC16F87/88
2.2.2.6
PIE2 Register
The PIE2 register contains the individual enable bit for
the EEPROM write operation interrupt.
REGISTER 2-6:
PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2 (ADDRESS 8Dh)
R/W-0
OSFIE
bit 7
R/W-0
CMIE
U-0
—
R/W-0
EEIE
U-0
—
bit 7
OSFIE: Oscillator Fail Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 6
CMIE: Comparator Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 5
Unimplemented: Read as ‘0’
bit 4
EEIE: EEPROM Write Operation Interrupt Enable bit
1 = Enabled
0 = Disabled
bit 3-0
Unimplemented: Read as ‘0’
U-0
—
U-0
—
U-0
—
bit 0
Legend:
DS30487B-page 22
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
2.2.2.7
PIR2 Register
The PIR2 register contains the flag bit for the EEPROM
write operation interrupt.
.
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit, or the global
enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt.
REGISTER 2-7:
PIR2: PERIPHERAL INTERRUPT STATUS REGISTER 2 (ADDRESS 0Dh)
R/W-0
OSFIF
bit 7
R/W-0
CMIF
U-0
—
R/W-0
EEIF
U-0
—
U-0
—
U-0
—
U-0
—
bit 0
bit 7
OSFIF: Oscillator Fail Interrupt Flag bit
1 = System oscillator failed, clock input has changed to INTRC (must be cleared in software)
0 = System clock operating
bit 6
CMIF: Comparator Interrupt Flag bit
1 = Comparator input has changed (must be cleared in software)
0 = Comparator input has not changed
bit 5
Unimplemented: Read as ‘0’
bit 4
EEIF: EEPROM Write Operation Interrupt Flag bit
1 = The write operation completed (must be cleared in software)
0 = The write operation is not complete or has not been started
bit 3-0
Unimplemented: Read as ‘0’
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 23
PIC16F87/88
2.2.2.8
Note:
PCON Register
Note:
Interrupt flag bits get set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an
interrupt.
The Power Control (PCON) register contains a flag bit
to allow differentiation between a Power-on Reset
(POR), a Brown-out Reset, an external MCLR Reset
and WDT Reset.
REGISTER 2-8:
BOR is unknown on Power-on Reset. It
must then be set by the user and checked
on subsequent RESETS to see if BOR is
clear, indicating a brown-out has occurred.
The BOR status bit is a ‘don't care’ and is
not necessarily predictable if the brownout circuit is disabled (by clearing the
BOREN bit in the Configuration Word
register).
PCON: POWER CONTROL REGISTER (ADDRESS 8Eh)
U-0
U-0
U-0
U-0
U-0
U-0
R/W-0
R/W-x
—
—
—
—
—
—
POR
BOR
bit 7
bit 0
bit 7-2
Unimplemented: Read as ‘0’
bit 1
POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0
BOR: Brown-out Reset Status bit
1 = No Brown-out Reset occurred
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Legend:
DS30487B-page 24
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
2.3
PCL and PCLATH
The program counter (PC) is 13-bits wide. The low byte
comes from the PCL register which is a readable and
writable register. The upper bits (PC<12:8>) are not
readable but are indirectly writable through the
PCLATH register. On any RESET, the upper bits of the
PC will be cleared. Figure 2-4 shows the two situations
for the loading of the PC. The upper example in the figure shows how the PC is loaded on a write to PCL
(PCLATH<4:0> → PCH). The lower example in the figure shows how the PC is loaded during a CALL or GOTO
instruction (PCLATH<4:3> → PCH).
FIGURE 2-4:
LOADING OF PC IN
DIFFERENT SITUATIONS
PCL
PCH
12
8
7
0
PC
8
PCLATH<4:0>
5
Instruction with
PCL as
Destination
ALU
PCLATH
PCH
12
11 10
PCL
8
0
7
PC
PCLATH<4:3>
11
2: There are no instructions/mnemonics
called PUSH or POP. These are actions
that occur from the execution of the
CALL, RETURN, RETLW and RETFIE
instructions, or the vectoring to an
interrupt address.
2.4
Program Memory Paging
All PIC16F87/88 devices are capable of addressing a
continuous 8K word block of program memory. The
CALL and GOTO instructions provide only 11 bits of
address to allow branching within any 2K program
memory page. When doing a CALL or GOTO instruction,
the upper 2 bits of the address are provided by
PCLATH<4:3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bits are
programmed so that the desired program memory
page is addressed. If a return from a CALL instruction
(or interrupt) is executed, the entire 13-bit PC is popped
off the stack. Therefore, manipulation of the
PCLATH<4:3> bits is not required for the RETURN
instructions (which POPs the address from the stack).
Note:
GOTO,CALL
2
Note 1: There are no status bits to indicate stack
overflow or stack underflow conditions.
Opcode <10:0>
PCLATH
2.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). When doing a
table read using a computed GOTO method, care
should be exercised if the table location crosses a PCL
memory boundary (each 256-byte block). Refer to the
application note, “AN556, Implementing a Table Read”.
2.3.2
Example 2-1 shows the calling of a subroutine in
page 1 of the program memory. This example assumes
that PCLATH is saved and restored by the Interrupt
Service Routine (if interrupts are used).
EXAMPLE 2-1:
CALL SUB1_P1
:
:
ORG 0x900
;Select page 1
;(800h-FFFh)
;Call subroutine in
;page 1 (800h-FFFh)
;page 1 (800h-FFFh)
SUB1_P1
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
 2003 Microchip Technology Inc.
CALL OF A SUBROUTINE
IN PAGE 1 FROM PAGE 0
ORG 0x500
BCF PCLATH,4
BSF PCLATH,3
STACK
The PIC16F87/88 family has an 8-level deep x 13-bit
wide hardware stack. The stack space is not part of
either program or data space and the stack pointer is not
readable or writable. The PC is PUSHed onto the stack
when a CALL instruction is executed or an interrupt
causes a branch. The stack is POPed in the event of a
RETURN, RETLW or a RETFIE instruction execution.
PCLATH is not affected by a PUSH or POP operation.
The contents of the PCLATH register are
unchanged after a RETURN or RETFIE
instruction is executed. The user must
rewrite the contents of the PCLATH register for any subsequent subroutine calls or
GOTO instructions.
Preliminary
:
:
RETURN
;called subroutine
;page 1 (800h-FFFh)
;return to
;Call subroutine
;in page 0
;(000h-7FFh)
DS30487B-page 25
PIC16F87/88
2.5
Indirect Addressing, INDF and
FSR Registers
A simple program to clear RAM locations 20h-2Fh
using indirect addressing is shown in Example 2-2.
The INDF register is not a physical register. Addressing
the INDF register will cause indirect addressing.
EXAMPLE 2-2:
Indirect addressing is possible by using the INDF register. Any instruction using the INDF register actually
accesses the register pointed to by the File Select Register, FSR. Reading the INDF register itself, indirectly
(FSR = 0) will read 00h. Writing to the INDF register
indirectly results in a no operation (although status bits
may be affected). An effective 9-bit address is obtained
by concatenating the 8-bit FSR register and the IRP bit
(STATUS<7>) as shown in Figure 2-5.
FIGURE 2-5:
MOVLW
MOVWF
CLRF
INCF
BTFSS
GOTO
NEXT
Bank Select
;initialize pointer
;to RAM
;clear INDF register
;inc pointer
;all done?
;no clear next
CONTINUE
:
;yes continue
DIRECT/INDIRECT ADDRESSING
Direct Addressing
RP1:RP0
INDIRECT ADDRESSING
0x20
FSR
INDF
FSR,F
FSR,4
NEXT
6
Indirect Addressing
From Opcode
0
IRP
7
FSR Register
Bank Select
Location Select
00
01
10
0
Location Select
11
00h
80h
100h
180h
7Fh
FFh
17Fh
1FFh
Data
Memory(1)
Bank 0
Note 1:
Bank 1
Bank 2
Bank 3
For register file map detail, see Figure 2-2 or Figure 2-3.
DS30487B-page 26
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
3.0
DATA EEPROM AND FLASH
PROGRAM MEMORY
3.1
The data EEPROM and FLASH program memory are
readable and writable during normal operation (over
the full VDD range). This memory is not directly mapped
in the register file space. Instead, it is indirectly
addressed through the Special Function Registers.
There are six SFRs used to read and write this
memory:
•
•
•
•
•
•
EEADR and EEADRH
The EEADRH:EEADR register pair can address up to
a maximum of 256 bytes of data EEPROM, or up to a
maximum of 8K words of program EEPROM. When
selecting a data address value, only the LSByte of the
address is written to the EEADR register. When selecting a program address value, the MSByte of the
address is written to the EEADRH register and the
LSByte is written to the EEADR register.
If the device contains less memory than the full address
reach of the address register pair, the Most Significant
bits of the registers are not implemented. For example,
if the device has 128 bytes of data EEPROM, the Most
Significant bit of EEADR is not implemented on access
to data EEPROM.
EECON1
EECON2
EEDATA
EEDATH
EEADR
EEADRH
When interfacing the data memory block, EEDATA
holds the 8-bit data for read/write and EEADR holds the
address of the EEPROM location being accessed. The
PIC16F87/88 devices have 256 bytes of data
EEPROM with an address range from 00h to 0FFh.
When writing to unimplemented locations, the charge
pump will be turned off.
When interfacing the program memory block, the
EEDATA and EEDATH registers form a two-byte word
that holds the 14-bit data for read/write, and the
EEADR and EEADRH registers form a two-byte word
that holds the 13-bit address of the EEPROM location
being accessed. The PIC16F87/88 devices have 4K
words of program FLASH with an address range from
0000h to 0FFFh. Addresses above the range of the
respective device will wraparound to the beginning of
program memory.
The EEPROM data memory allows single byte read
and write. The FLASH program memory allows single
word reads and four-word block writes. Program memory writes must first start with a 32-word block erase,
then write in 4-word blocks. A byte write in data
EEPROM memory automatically erases the location
and writes the new data (erase before write).
The write time is controlled by an on-chip timer. The
write/erase voltages are generated by an on-chip
charge pump, rated to operate over the voltage range
of the device for byte or word operations.
3.2
EECON1 and EECON2 Registers
EECON1 is the control register for memory accesses.
Control bit EEPGD determines if the access will be a
program or data memory access. When clear, as it is
when reset, any subsequent operations will operate on
the data memory. When set, any subsequent
operations will operate on the program memory.
Control bits RD and WR initiate read and write,
respectively. These bits cannot be cleared, only set in
software. They are cleared in hardware at completion
of the read or write operation. The inability to clear the
WR bit in software prevents the accidental, premature
termination of a write operation.
The WREN bit, when set, will allow a write or erase
operation. On power-up, the WREN bit is clear. The
WRERR bit is set when a write (or erase) operation is
interrupted by a MCLR, or a WDT Time-out Reset during normal operation. In these situations, following
RESET, the user can check the WRERR bit and rewrite
the location. The data and address will be unchanged
in the EEDATA and EEADR registers.
Interrupt flag bit, EEIF in the PIR2 register, is set when
write is complete. It must be cleared in software.
EECON2 is not a physical register. Reading EECON2
will read all ‘0’s. The EECON2 register is used
exclusively in the EEPROM write sequence.
When the device is code protected, the CPU may
continue to read and write the data EEPROM memory.
Depending on the settings of the write protect bits, the
device may or may not be able to write certain blocks
of the program memory; however, reads of the program
memory are allowed. When code protected, the device
programmer can no longer access data or program
memory; this does NOT inhibit internal reads or writes.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 27
PIC16F87/88
REGISTER 3-1:
EECON1: EEPROM ACCESS CONTROL REGISTER 1 (ADDRESS 18Ch)
R/W-x
U-0
U-0
R/W-x
R/W-x
R/W-0
R/S-0
R/S-0
EEPGD
—
—
FREE
WRERR
WREN
WR
RD
bit 7
bit 0
bit 7
EEPGD: Program/Data EEPROM Select bit
1 = Accesses program memory
0 = Accesses data memory
bit 6-5
Unimplemented: Read as ‘0’
bit 4
FREE: EEPROM Forced Row Erase bit
1 = Erase the program memory row addressed by EEADRH:EEADR on the next WR command
0 = Perform write only
bit 3
WRERR: EEPROM Error Flag bit
1 = A write operation is prematurely terminated (any MCLR or any WDT Reset during normal
operation)
0 = The write operation completed
bit 2
WREN: EEPROM Write Enable bit
1 = Allows write cycles
0 = Inhibits write to the EEPROM
bit 1
WR: Write Control bit
1 = Initiates a write cycle. The bit is cleared by hardware once write is complete. The WR bit
can only be set (not cleared) in software.
0 = Write cycle to the EEPROM is complete
bit 0
RD: Read Control bit
1 = Initiates an EEPROM read, RD is cleared in hardware. The RD bit can only be set (not
cleared) in software.
0 = Does not initiate an EEPROM read
Legend:
DS30487B-page 28
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’ S = Set only
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
3.3
Reading Data EEPROM Memory
To read a data memory location, the user must write the
address to the EEADR register, clear the EEPGD control bit (EECON1<7>) and then set control bit RD
(EECON1<0>). The data is available in the very next
cycle in the EEDATA register; therefore, it can be read
in the next instruction (see Example 3-1). EEDATA will
hold this value until another read or until it is written to
by the user (during a write operation).
The steps to write to EEPROM data memory are:
1.
2.
3.
4.
The steps to reading the EEPROM data memory are:
1.
Write the address to EEADR. Make sure that the
address is not larger than the memory size of
the device.
Clear the EEPGD bit to point to EEPROM data
memory.
Set the RD bit to start the read operation.
Read the data from the EEDATA register.
2.
3.
4.
EXAMPLE 3-1:
BANKSEL EEADR
MOVF
ADDR,W
MOVWF
EEADR
3.4
Write 55h to EECON2 in two steps (first to W,
then to EECON2).
Write AAh to EECON2 in two steps (first to W,
then to EECON2).
Set the WR bit.
DATA EEPROM READ
;
;
;
;
BANKSEL EECON1
;
BCF
EECON1,EEPGD ;
BSF
EECON1,RD
;
BANKSEL EEDATA
;
MOVF
EEDATA,W
;
5.
6.
7.
If step 10 is not implemented, check the WR bit
to see if a write is in progress.
Write the address to EEADR. Make sure that the
address is not larger than the memory size of
the device.
Write the 8-bit data value to be programmed in
the EEDATA register.
Clear the EEPGD bit to point to EEPROM data
memory.
Set the WREN bit to enable program operations.
Disable interrupts (if enabled).
Execute the special five instruction sequence:
Select Bank of EEADR
Data Memory Address
to read
Select Bank of EECON1
Point to Data memory
EE Read
Select Bank of EEDATA
W = EEDATA
Writing to Data EEPROM Memory
8.
9.
Enable interrupts (if using interrupts).
Clear the WREN bit to disable program
operations.
10. At the completion of the write cycle, the WR bit
is cleared and the EEIF interrupt flag bit is set
(EEIF must be cleared by firmware). If step 1 is
not implemented, then firmware should check
for EEIF to be set, or WR to clear, to indicate the
end of the program cycle.
EXAMPLE 3-2:
DATA EEPROM WRITE
BANKSEL EECON1
; Select Bank of
; EECON1
BTFSC
EECON1,WR
; Wait for write
GOTO
$-1
; to complete
BANKSEL EEADR
; Select Bank of
; EEADR
MOVF
ADDR,W
;
MOVWF
EEADR
; Data Memory
; Address to write
MOVF
VALUE,W
;
MOVWF
EEDATA
; Data Memory Value
; to write
BANKSEL EECON1
; Select Bank of
; EECON1
BCF
EECON1,EEPGD; Point to DATA
; memory
BSF
EECON1,WREN ; Enable writes
To write an EEPROM data location, the user must first
write the address to the EEADR register and the data to
the EEDATA register. Then, the user must follow a
specific write sequence to initiate the write for each byte.
The write will not initiate if the write sequence is not
exactly followed (write 55h to EECON2, write AAh to
EECON2, then set WR bit) for each byte. We strongly
recommend that interrupts be disabled during this
code segment (see Example 3-2).
After a write sequence has been initiated, clearing the
WREN bit will not affect this write cycle. The WR bit will
be inhibited from being set unless the WREN bit is set.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EE Write Complete
Interrupt Flag bit (EEIF) is set. The user can either
enable this interrupt or poll this bit. EEIF must be
cleared by software.
 2003 Microchip Technology Inc.
Required
Sequence
Additionally, the WREN bit in EECON1 must be set to
enable write. This mechanism prevents accidental
writes to data EEPROM due to errant (unexpected)
code execution (i.e., lost programs). The user should
keep the WREN bit clear at all times except when
updating EEPROM. The WREN bit is not cleared
by hardware
Preliminary
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
BCF
INTCON,GIE
55h
EECON2
AAh
EECON2
EECON1,WR
;
;
;
;
;
;
;
INTCON,GIE ;
EECON1,WREN ;
Disable INTs.
Write 55h
Write AAh
Set WR bit to
begin write
Enable INTs.
Disable writes
DS30487B-page 29
PIC16F87/88
3.5
Reading FLASH Program Memory
3.6
Erasing FLASH Program Memory
To read a program memory location, the user must
write two bytes of the address to the EEADR and
EEADRH registers, set the EEPGD control bit
(EECON1<7>), and then set control bit RD
(EECON1<0>). Once the read control bit is set, the
program memory FLASH controller will use the second
instruction cycle to read the data. This causes the
second instruction immediately following the “BSF
EECON1,RD” instruction to be ignored. The data is
available in the very next cycle in the EEDATA and
EEDATH registers; therefore, it can be read as two
bytes in the following instructions. EEDATA and
EEDATH registers will hold this value until another read
or until it is written to by the user (during a write
operation).
The minimum erase block is 32 words. Only through
the use of an external programmer, or through ICSP
control, can larger blocks of program memory be bulk
erased. Word erase in the FLASH array is not
supported.
EXAMPLE 3-3:
For protection, the write initiate sequence for EECON2
must be used.
BANKSEL EEADRH
MOVF
ADDRH, W
MOVWF
EEADRH
FLASH PROGRAM READ
;
;
;
;
MOVF
ADDRL, W
;
MOVWF
EEADR
;
;
BANKSEL EECON1
;
BSF
EECON1, EEPGD ;
;
BSF
EECON1, RD
;
;
NOP
;
;
NOP
;
;
;
BANKSEL EEDATA
;
MOVF
EEDATA, W
;
MOVWF
DATAL
;
MOVF
EEDATH, W
;
MOVWF
DATAH
;
Select Bank of EEADRH
MS Byte of Program
Address to read
LS Byte of Program
Address to read
Select Bank of EECON1
Point to PROGRAM
memory
EE Read
When initiating an erase sequence from the microcontroller itself, a block of 32 words of program memory is
erased. The Most Significant 11 bits of the
EEADRH:EEADR point to the block being erased.
EEADR< 4:0> are ignored.
The EECON1 register commands the erase operation.
The EEPGD bit must be set to point to the FLASH program memory. The WREN bit must be set to enable
write operations. The FREE bit is set to select an erase
operation.
After the “BSF EECON1,WR” instruction, the processor
requires two cycles to setup the erase operation. The
user must place two NOP instructions after the WR bit is
set. The processor will halt internal operations for the
typical 2 ms, only during the cycle in which the erase
takes place. This is not SLEEP mode, as the clocks and
peripherals will continue to run. After the erase cycle,
the processor will resume operation with the third
instruction after the EECON1 write instruction.
Any instructions
here are ignored as
program memory is
read in second cycle
after BSF EECON1,RD
Select Bank of EEDATA
DATAL = EEDATA
3.6.1
DATAH = EEDATH
2.
The sequence of events for erasing a block of internal
program memory location is:
1.
3.
4.
5.
6.
7.
DS30487B-page 30
FLASH PROGRAM MEMORY
ERASE SEQUENCE
Preliminary
Load EEADRH:EEADR with address of row
being erased.
Set EEPGD bit to point to program memory, set
WREN bit to enable writes, and set FREE bit to
enable the erase.
Disable interrupts.
Write 55h to EECON2.
Write AAh to EECON2.
Set the WR bit. This will begin the row erase
cycle.
The CPU will stall for duration of the erase.
 2003 Microchip Technology Inc.
PIC16F87/88
EXAMPLE 3-4:
ERASING A FLASH PROGRAM MEMORY ROW
BANKSEL
MOVF
MOVWF
MOVF
MOVWF
EEADRH
ADDRH, W
EEADRH
ADDRL, W
EEADR
; Select Bank of EEADRH
;
; MS Byte of Program Address to Erase
;
; LS Byte of Program Address to Erase
BANKSEL
BSF
BSF
BSF
EECON1
EECON1, EEPGD
EECON1, WREN
EECON1, FREE
;
;
;
;
Select Bank of EECON1
Point to PROGRAM memory
Enable Write to memory
Enable Row Erase operation
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
NOP
INTCON, GIE
55h
EECON2
AAh
EECON2
EECON1, WR
;
;
;
;
;
;
;
;
;
;
;
;
Disable interrupts (if using)
ERASE_ROW
;
NOP
BCF
BSF
EECON1, WREN
INTCON, GIE
 2003 Microchip Technology Inc.
Write 55h
Write AAh
Start Erase (CPU stall)
Any instructions here are ignored as processor
halts to begin Erase sequence
processor will stop here and wait for Erase complete
after Erase processor continues with 3rd instruction
Disable writes
Enable interrupts (if using)
Preliminary
DS30487B-page 31
PIC16F87/88
3.7
Writing to FLASH Program
Memory
There are 4 buffer register words and all four locations
MUST be written to with correct data.
After the “BSF EECON1,WR” instruction, if
EEADR ≠ xxxxxx11, then a short write will occur.
This short write only transfers the data to the buffer register. The WR bit will be cleared in hardware after 1
cycle. The core will not halt and there will be no
EEWHLT signal generated.
FLASH program memory may only be written to if the
destination address is in a segment of memory that is
not write protected, as defined in bits WRT1:WRT0 of
the device configuration word (Register 15-1). FLASH
program memory must be written in four-word blocks.
A block consists of four words with sequential
addresses, with a lower boundary defined by an
address, where EEADR<1:0> = 00. At the same time,
all block writes to program memory are done as write
only operations. The program memory must first be
erased. The write operation is edge-aligned, and
cannot occur across boundaries.
After the “BSF EECON1,WR” instruction, if
EEADR = xxxxxx11, then a long write will occur. This
will simultaneously transfer the data from
EEDATH:EEDATA to the buffer registers and begin the
write of all four words. The processor will execute the
next instruction and then ignore the subsequent
instruction. The user should place NOP instructions into
the second words. The processor will then halt internal
operations for typically 2 msec in which the write takes
place. This is not SLEEP mode, as the clocks and
peripherals will continue to run. After the write cycle,
the processor will resume operation with the 3rd
instruction after the EECON1 write instruction.
To write to the program memory, the data must first be
loaded into the buffer registers. There are four 14-bit
buffer registers and they are addressed by the low
2 bits of EEADR.
Loading data into the buffer registers is accomplished
via the EEADR, EEADT, EECON1 and EECON2
registers as follows:
•
•
•
•
•
After each long write, the 4 buffer registers will be reset
to 3FFF.
Set EECON1 PGD and WREN
Write address to EEADRH:EEADR
Write data to EEDATA:EEDATH
Write 55, AA to EECON2
Set WR bit in EECON1
FIGURE 3-1:
BLOCK WRITES TO FLASH PROGRAM MEMORY
7
5
0
0 7
EEDATH
EEDATA
6
8
14
14
All buffers are
transferred
to FLASH
automatically
after this word
is written
First word of block
to be written
14
EEADR<1:0>
= 00
Buffer Register
EEADR<1:0>
= 10
EEADR<1:0>
= 01
Buffer Register
Buffer Register
14
EEADR<1:0>
= 11
Buffer Register
Program Memory
DS30487B-page 32
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
An example of the complete four-word write sequence
is shown in Example 3-5. The initial address is loaded
into the EEADRH:EEADR register pair; the four words
of data are loaded using indirect addressing, assuming
that a row erase sequence has already been
performed.
EXAMPLE 3-5:
WRITING TO FLASH PROGRAM MEMORY
; This write routine assumes the following:
;
;
;
;
;
;
1.
2.
3.
4.
5.
6.
The 32 words in the erase block have already been erased.
A valid starting address (the least significant bits = '00') is loaded into EEADRH:EEADR
This example is starting at 0x100, this is an application dependent setting.
The 8 bytes (4 words) of data are loaded, starting at an address in RAM called ARRAY.
This is an example only, location of data to program is application dependent.
word_block is located in data memory.
BANKSEL EECON1
BSF
EECON1,EEPGD
BSF
EECON1,WREN
;prepare for WRITE procedure
;point to program memory
;allow write cycles
BANKSEL word_block
MOVLW
.4
MOVWF
word_block
;prepare for 4 words to be written
BANKSEL
MOVLW
MOVWF
MOVLW
MOVWF
BANKSEL
MOVLW
MOVWF
EEADRH
0x01
EEADRH
0x00
EEADR
ARRAY
ARRAY
FSR
BANKSEL
MOVF
MOVWF
INCF
MOVF
MOVWF
INCF
EEDATA
INDF,W
EEDATA
FSR,F
INDF,W
EEDATH
FSR,F
BANKSEL
MOVLW
MOVWF
MOVLW
MOVWF
BSF
NOP
NOP
EECON1
0x55
EECON2
0xAA
EECON2
EECON1,WR
BANKSEL
INCF
BANKSEL
DECFSZ
GOTO
EEADR
EEADR,f
word_block
word_block,f
loop
;Start writing at 0x100
;load HIGH address
;load LOW address
;initialize FSR to start of data
Required
Sequence
LOOP
BANKSEL EECON1
BCF
EECON1,WREN
BSF
INTCON,GIE
 2003 Microchip Technology Inc.
;indirectly load EEDATA
;increment data pointer
;indirectly load EEDATH
;increment data pointer
;required sequence
;set WR bit to begin write
;instructions here are ignored as processor
;load next word address
;have 4 words been written?
;NO, continue with writing
;YES, 4 words complete, disable writes
;enable interrupts
Preliminary
DS30487B-page 33
PIC16F87/88
3.8
Protection Against Spurious Write
3.9
There are conditions when the device should not write
to the data EEPROM memory. To protect against spurious EEPROM writes, various mechanisms have been
built-in. On power-up, WREN is cleared. Also, the
Power-up Timer (72 ms duration) prevents an
EEPROM write.
When the data EEPROM is code protected, the microcontroller can read and write to the EEPROM normally.
However, all external access to the EEPROM is
disabled. External write access to the program memory
is also disabled.
When program memory is code protected, the microcontroller can read and write to program memory normally, as well as execute instructions. Writes by the
device may be selectively inhibited to regions of the
memory depending on the setting of bits WRT1:WRT0
of the configuration word (see Section 15.1 “Configuration Bits” for additional information). External
access to the memory is also disabled.
The write initiate sequence and the WREN bit together
help prevent an accidental write during brown-out,
power glitch, or software malfunction.
TABLE 3-1:
Address
Operation During Code Protect
REGISTERS/BITS ASSOCIATED WITH DATA EEPROM AND
FLASH PROGRAM MEMORIES
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
Power-on
Reset
Value on
all other
RESETS
10Ch
EEDATA EEPROM/FLASH Data Register Low Byte
xxxx xxxx uuuu uuuu
10Dh
EEADR
xxxx xxxx uuuu uuuu
10Eh
EEDATH
—
—
10Fh
EEADRH
—
—
—
—
—
18Ch
EECON1 EEPGD
—
—
FREE
WRERR
18Dh
EECON2 EEPROM Control Register 2 (not a physical register)
0Dh
PIR2
OSFIF
CMIF
—
EEIF
—
8Dh
PIE2
OSFIE
CMIE
—
EEIE
—
Legend:
EEPROM/FLASH Address Register Low Byte
EEPROM/FLASH Data Register High Byte
--xx xxxx --uu uuuu
EEPROM/FLASH Address
Register High Byte
WREN
---- -xxx ---- -uuu
WR
RD
x--x x000 x--x q000
—
—
—
00-0 ---- 00-0 ----
—
—
—
00-0 ---- 00-0 ----
---- ---- ---- ----
x = unknown, u = unchanged, - = unimplemented, read as ‘0’, q = value depends upon condition.
Shaded cells are not used by data EEPROM or FLASH program memory.
DS30487B-page 34
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
4.0
OSCILLATOR
CONFIGURATIONS
4.1
Oscillator Types
TABLE 4-1:
The PIC16F87/88 can be operated in eight different
oscillator modes. The user can program three configuration bits (FOSC2:FOSC0) to select one of these eight
modes (modes 5-8 are new PIC16 oscillator
configurations):
1.
2.
3.
4.
LP
XT
HS
RC
5.
RCIO
6.
INTIO1
7.
INTIO2
8.
ECIO
4.2
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
External Resistor/Capacitor with
FOSC/4 output on RA6
External Resistor/Capacitor with
I/O on RA6
Internal Oscillator with FOSC/4
output on RA6 and I/O on RA7
Internal Oscillator with I/O on RA6
and RA7
External Clock with I/O on RA6
C2
LP
32 kHz
33 pF
33 pF
200 kHz
56 pF
56 pF
1 MHz
15 pF
15 pF
4 MHz
15 pF
15 pF
4 MHz
15 pF
15 pF
8 MHz
15 pF
15 pF
20 MHz
15 pF
15 pF
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application.
See the notes following this table for additional
information.
Note 1: Higher capacitance increases the stability
of oscillator but also increases the
start-up time.
2: Since each crystal has its own characteristics, the user should consult the crystal
manufacturer for appropriate values of
external components.
3: Rs may be required in HS mode, as well
as XT mode, to avoid overdriving crystals
with low drive level specification.
PIC16F87/88
4: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
C1(1)
RF(3)
C1
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
were not optimized.
CRYSTAL OPERATION
(HS, XT, OR LP OSC
CONFIGURATION)
XTAL
Typical Capacitor Values
Tested:
Capacitor values are for design guidance only.
In XT, LP or HS modes, a crystal or ceramic resonator
is connected to the OSC1/CLKI and OSC2/CLKO pins
to establish oscillation (see Figure 4-1 and Figure 4-2).
The PIC16F87/88 oscillator design requires the use of
a parallel cut crystal. Use of a series cut crystal may
give a frequency out of the crystal manufacturers
specifications.
OSC1
Crystal
Freq
XT
HS
Crystal Oscillator/Ceramic
Resonators
FIGURE 4-1:
Osc Type
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR (FOR
DESIGN GUIDANCE ONLY)
SLEEP
OSC2
C2(1)
RS(2)
To Internal
Logic
Note1: See Table 4-1 for typical values of C1 and C2.
2: A series resistor (RS) may be required for AT strip
cut crystals.
3: RF varies with the crystal chosen (typically
between 2 MΩ to 10 MΩ).
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 35
PIC16F87/88
FIGURE 4-2:
CERAMIC RESONATOR
OPERATION (HS OR XT
OSC CONFIGURATION)
OSC1
PIC16F87/88
C1(1)
RES
RF(3)
RS
External Clock Input
The ECIO Oscillator mode requires an external clock
source to be connected to the OSC1 pin. There is no
oscillator start-up time required after a Power-on
Reset, or after an exit from SLEEP mode.
In the ECIO Oscillator mode, the OSC2 pin becomes
an additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6). Figure 4-3 shows the
pin connections for the ECIO Oscillator mode.
SLEEP
OSC2
C2(1)
4.3
(2)
To Internal
Logic
FIGURE 4-3:
EXTERNAL CLOCK INPUT
OPERATION
(ECIO CONFIGURATION)
Note 1: See Table 4-2 for typical values of C1 and
C2.
2: A series resistor (RS) may be required.
3: RF varies with the resonator chosen
(typically between 2 MΩ to 10 MΩ).
OSC1/CLKI
Clock from
Ext. System
PIC16F87/88
RA6
TABLE 4-2:
I/O (OSC2)
CERAMIC RESONATORS
(FOR DESIGN GUIDANCE
ONLY)
Typical Capacitor Values Used:
Mode
Freq
OSC1
OSC2
XT
455 kHz
2.0 MHz
4.0 MHz
56 pF
47 pF
33 pF
56 pF
47 pF
33 pF
HS
8.0 MHz
16.0 MHz
27 pF
22 pF
27 pF
22 pF
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values were not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application.
See the notes following this table for additional
information.
Note:
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any VDD for
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of RS is 330Ω.
DS30487B-page 36
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
4.4
RC Oscillator
4.5
For timing insensitive applications, the “RC” and
“RCIO” device options offer additional cost savings.
The RC oscillator frequency is a function of the supply
voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this,
the oscillator frequency will vary from unit to unit due to
normal manufacturing variation. Furthermore, the difference in lead frame capacitance between package
types will also affect the oscillation frequency,
especially for low CEXT values. The user also needs to
take into account variation due to tolerance of external
R and C components used. Figure 4-4 shows how the
R/C combination is connected.
In the RC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal may
be used for test purposes or to synchronize other logic.
FIGURE 4-4:
RC OSCILLATOR MODE
VDD
Internal
Clock
The main output (INTOSC) is an 8 MHz clock source,
which can be used to directly drive the system clock. It
also drives the INTOSC postscaler which can provide a
range of six clock frequencies from 125 kHz to 4 MHz.
The other clock source is the internal RC oscillator
(INTRC) which provides a 31.25 kHz (32 µs nominal
period) output. The INTRC oscillator is enabled by
selecting the INTRC as the system clock source, or
when any of the following are enabled:
•
•
•
•
Power-up Timer
Watchdog Timer
Two-Speed Start-up
Fail-Safe Clock Monitor
The clock source frequency (INTOSC direct, INTRC
direct, or INTOSC postscaler) is selected by configuring
the IRCF bits of the OSCCON register (page 40).
CEXT
PIC16F87/88
VSS
The PIC16F87/88 devices include an internal oscillator
block, which generates two different clock signals;
either can be used as the system’s clock source. This
can eliminate the need for external oscillator circuits on
the OSC1 and/or OSC2 pins.
These features are discussed in greater detail in
Section 15.0 “Special Features of the CPU”.
REXT
OSC1
Note:
OSC2/CLKO
FOSC/4
Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ
CEXT > 20 pF
The RCIO Oscillator mode (Figure 4-5) functions like
the RC mode, except that the OSC2 pin becomes an
additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6).
FIGURE 4-5:
Internal Oscillator Block
Throughout this data sheet, when referring
specifically to a generic clock source, the
term “INTRC” may also be used to refer to
the clock modes using the internal oscillator block. This is regardless of whether the
actual frequency used is INTOSC
(8 MHz), the INTOSC postscaler, or
INTRC (31.25 kHz).
RCIO OSCILLATOR MODE
VDD
REXT
OSC1
Internal
Clock
CEXT
PIC16F87/88
VSS
RA6
I/O (OSC2)
Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ
CEXT > 20 pF
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 37
PIC16F87/88
4.5.1
INTRC MODES
4.5.2
Using the internal oscillator as the clock source can
eliminate the need for up to two external oscillator pins,
after which it can be used for digital I/O. Two distinct
configurations are available:
• In INTIO1 mode, the OSC2 pin outputs FOSC/4,
while OSC1 functions as RA7 for digital input and
output.
• In INTIO2 mode, OSC1 functions as RA7 and
OSC2 functions as RA6, both for digital input and
output.
REGISTER 4-1:
The internal oscillator’s output has been calibrated at the
factory but can be adjusted in the application. This is
done by writing to the OSCTUNE register (Register 4-1).
The tuning sensitivity is constant throughout the tuning
range. The OSCTUNE register has a tuning range of
±12.5%.
When the OSCTUNE register is modified, the INTOSC
and INTRC frequencies will begin shifting to the new frequency. The INTRC clock will reach the new frequency
within 8 clock cycles (approximately 8 * 32 µs = 256 µs);
the INTOSC clock will stabilize within 1 ms. Code execution continues during this shift. There is no indication that
the shift has occurred. Operation of features that depend
on the 31.25 kHz INTRC clock source frequency, such
as the WDT, Fail-Safe Clock Monitor and peripherals,
will also be affected by the change in frequency.
OSCTUNE: OSCILLATOR TUNING REGISTER (ADDRESS 90h)
U-0
—
bit 7
bit 7-6
bit 5-0
OSCTUNE REGISTER
U-0
—
R/W-0
TUN5
R/W-0
TUN4
R/W-0
TUN3
R/W-0
TUN2
R/W-0
TUN1
R/W-0
TUN0
bit 0
Unimplemented: Read as ‘0’
TUN<5:0>: Frequency Tuning bits
011111 = Maximum frequency
011110 =
•
•
•
000001 =
000000 = Center frequency. Oscillator module is running at the calibrated frequency.
111111 =
•
•
•
100000 = Minimum frequency
Legend:
R = Readable bit
-n = Value at POR
DS30487B-page 38
W = Writable bit
‘1’ = Bit is set
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
4.6
Clock Sources and Oscillator
Switching
The PIC16F87/88 devices include a feature that allows
the system clock source to be switched from the main
oscillator to an alternate low frequency clock source.
PIC16F87/88 devices offer three alternate clock
sources. When enabled, these give additional options
for switching to the various Power Managed Operating
modes.
FOSC2:FOSC0 configuration bits in Configuration Register 1. When the bits are set in any other manner, the
system clock source is provided by the Timer1 oscillator (SCS1:SCS0 = 01), or from the internal oscillator
block (SCS1:SCS0 = 10). After a RESET, SCS<1:0>
are always set to ‘00’.
Note:
Essentially, there are three clock sources for these
devices:
• Primary oscillators
• Secondary oscillators
• Internal oscillator block (INTRC)
The primary oscillators include the external Crystal
and Resonator modes, the external RC modes, the
external Clock mode and the internal oscillator block.
The particular mode is defined on POR by the contents
of Configuration Word 1. The details of these modes
are covered earlier in this chapter.
The secondary oscillators are those external sources
not connected to the OSC1 or OSC2 pins. These
sources may continue to operate even after the
controller is placed in a Power Managed mode.
PIC16F87/88 devices offer the Timer1 oscillator as a
secondary oscillator. This oscillator continues to run
when a SLEEP instruction is executed, and is often the
time base for functions such as a real-time clock.
Most often, a 32.768 kHz watch crystal is connected
between the RB6/T1OSO and RB7/T1OSI pins. Like
the LP mode oscillator circuit, loading capacitors are
also connected from each pin to ground. The Timer1
oscillator is discussed in greater detail in Section 7.6
“Timer1 Oscillator”.
In addition to being a primary clock source, the internal
oscillator block is available as a Power Managed
mode clock source. The 31.25 kHz INTRC source is
also used as the clock source for several special features, such as the WDT, Fail-Safe Clock Monitor,
Power-up Timer, and Two-Speed Start-up.
The clock sources for the PIC16F87/88 devices are
shown in Figure 4-6. See Section 7.0 “Timer1 Module” for further details of the Timer1 oscillator. See
Section 15.1 “Configuration Bits” for Configuration
register details.
4.6.1
OSCCON REGISTER
The OSCCON register (Register 4-2) controls several
aspects of the system clock’s operation, both in full
power operation and in Power Managed modes.
The Internal Oscillator Select bits, IRCF2:IRCF0, select
the frequency output of the internal oscillator block that
is used to drive the system clock. The choices are the
INTRC source (31.25 kHz), the INTOSC source
(8 MHz), or one of the six frequencies derived from the
INTOSC postscaler (125 kHz to 4 MHz). Changing the
configuration of these bits has an immediate change on
the internal oscillator’s output.
The OSTS and IOFS bits indicate the status of the primary oscillator and INTOSC source; these bits are set
when their respective oscillators are stable. In particular, OSTS indicates that the Oscillator Start-up Timer
has timed out.
4.6.2
CLOCK SWITCHING
Clock switching will occur for the following reasons:
• The FCMEN (CONFIG2<0>) bit is set, the device
is running from the primary oscillator, and the
primary oscillator fails. The clock source will be
31.25 kHz INTRC.
• The FCMEN bit is set, the device is running from
the T1OSC and T1OSC fails. The clock source
will be 31.25 kHz INTRC.
• Following a wake-up due to a RESET or a POR,
when the device is configured for Two-Speed
Start-up mode, switching will occur between the
INTRC and the system clock defined by the
FOSC<2:0> bits.
• A wake-up from SLEEP occurs due to interrupt or
WDT wake-up and Two-Speed Start-up is
enabled. If the primary clock is XT, HS, or LP, the
clock will switch between the INTRC and the primary system clock after 1024 clocks (OST) and 8
clocks of the primary oscillator. This is conditional
upon the SCS bits being set equal to ‘00’.
• SCS bits are modified from their original value.
• IRCF bits are modified from their original value.
Note:
The System Clock Select bits, SCS1:SCS0, select the
clock source that is used when the device is operating
in Power Managed modes. When the bits are
cleared (SCS<1:0> = 00), the system clock source
comes from the main oscillator that is selected by the
 2003 Microchip Technology Inc.
The instruction to immediately follow the
modification of SCS<1:0> will have an
instruction time (TCY) based on the previous clock source. This should be taken
into consideration when developing time
dependant code.
Preliminary
Because the SCS bits are cleared on any
RESET, no clock switching will occur on a
RESET unless the Two-Speed Start-up is
enabled and the primary clock is XT, HS,
or LP. The device will wait for the primary
clock to become stable before execution
begins (Two-Speed Start-up disabled).
DS30487B-page 39
PIC16F87/88
4.6.3
CLOCK TRANSITION AND WDT
When clock switching is performed, the Watchdog
Timer is disabled because the Watchdog ripple counter
is used as the Oscillator Start-up Timer.
Note:
Once the clock transition is complete (i.e., new oscillator selection switch has occurred), the Watchdog
counter is re-enabled with the Counter Reset. This
allows the user to synchronize the Watchdog Timer to
the start of execution at the new clock frequency.
The OST is only used when switching to
XT, HS, and LP Oscillator modes.
REGISTER 4-2:
OSCCON: OSCILLATOR CONTROL REGISTER (ADDRESS 8Fh)
U-0
—
bit 7
R/W-0
IRCF2
R/W-0
IRCF1
R/W-0
IRCF0
R-0
OSTS(1)
R/W-0
IOFS
R/W-0
SCS1
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IRCF<2:0>: Internal RC Oscillator Frequency Select bits
000 = 31.25 kHz
001 = 125 kHz
010 = 250 kHz
011 = 500 kHz
100 = 1 MHz
101 = 2 MHz
110 = 4 MHz
111 = 8 MHz
bit 3
OSTS: Oscillator Start-up Time-out Status bit(1)
1 = Device is running from the primary system clock
0 = Device is running from T1OSC or INTRC as a secondary system clock
R/W-0
SCS0
bit 0
Note 1: Bit resets to ‘0’ with Two-Speed Start-up mode, and LP, XT, or HS selected as the
oscillator mode.
bit 2
IOFS: INTOSC Frequency Stable bit
1 = Frequency is stable
0 = Frequency is not stable
bit 1-0
SCS<1:0>: Oscillator Mode Select bits
00 = Oscillator mode defined by FOSC<2:0>
01 = T1OSC is used for system clock
10 = Internal RC is used for system clock
11 = Reserved
Legend:
DS30487B-page 40
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 4-6:
PIC16F87/88 CLOCK DIAGRAM
Config1(FOSC2:FOSC0)
SCS<1:0>(T1OSC)
Primary Oscillator
OSC2
SLEEP
Secondary Oscillator
T1OSC
T1OSO
To Timer1
T1OSCEN
Enable
Oscillator
OSCCON<6:4>
8 MHz
4 MHz
Internal
Oscillator
Block
8 MHz
(INTOSC)
100
500 kHz
250 kHz
31.25 kHz
MODIFYING THE IRCF BITS
011
010
001
000
4.6.5
If the IRCF bits are modified while the internal oscillator
is running at any other frequency than INTRC
(31.25 kHz IRCF<2:0> ≠ 000), there is no need for a
4 ms clock switch delay. The new INTOSC frequency
will be stable immediately after the eight falling edges.
The IOFS bit will remain set after clock switching
occurs.
Caution must be taken when modifying the
IRCF bits using BCF or BSF instructions. It
is possible to modify the IRCF bits to a frequency that may be out of the VDD specification range; for example, VDD = 2.0V and
IRCF = 111 (8 MHz).
 2003 Microchip Technology Inc.
110
101
The IRCF bits can be modified at any time, regardless
of which clock source is currently being used as the system clock. The internal oscillator allows users to change
the frequency during run time. This is achieved by modifying the IRCF bits in the OSCCON register. The
sequence of events that occur after the IRCF bits are
modified is dependent upon the initial value of the IRCF
bits before they are modified. If the INTRC (31.25 kHz,
IRCF<2:0> = 000) is running and the IRCF bits are
modified to any other value than ‘000’, a 4 ms clock
switch delay is turned on. Code execution continues at
a higher than expected frequency while the new frequency stabilizes. Time sensitive code should wait for
the IOFS bit in the OSCCON register to become set
before continuing. This bit can be monitored to ensure
that the frequency is stable before using the system
clock in time critical applications.
Note:
CPU
111
1 MHz
125 kHz
31.25 kHz
(INTRC)
4.6.4
Internal Oscillator
2 MHz
Postscaler
31.25 kHz
Source
Peripherals
MUX
T1OSI
MUX
LP, XT, HS, RC, EC
OSC1
WDT, FSCM
CLOCK TRANSITION SEQUENCE
Following are three different sequences for switching
the internal RC oscillator frequency.
• Clock before switch: 31.25 kHz (IRCF<2:0> = 000)
1. IRCF bits are modified to an INTOSC/INTOSC
postscaler frequency.
2. The clock switching circuitry waits for a falling
edge of the current clock, at which point CLKO
is held low.
3. The clock switching circuitry then waits for eight
falling edges of requested clock, after which it
switches CLKO to this new clock source.
4. The IOFS bit is clear to indicate that the clock is
unstable and a 4 ms delay is started. Time
dependent code should wait for IOFS to become
set.
5. Switchover is complete.
• Clock before switch: One of INTOSC/INTOSC
postscaler (IRCF<2:0> ≠ 000)
1. IRCF
bits
are
modified
to
INTRC
(IRCF<2:0> = 000).
2. The clock switching circuitry waits for a falling
edge of the current clock, at which point CLKO
is held low.
3. The clock switching circuitry then waits for eight
falling edges of requested clock, after which it
switches CLKO to this new clock source.
4. Oscillator switchover is complete.
Preliminary
DS30487B-page 41
PIC16F87/88
4.6.6
• Clock before switch: One of INTOSC/INTOSC
postscaler (IRCF<2:0> ≠ 000)
1. IRCF bits are modified to a different INTOSC/
INTOSC postscaler frequency.
2. The clock switching circuitry waits for a falling
edge of the current clock, at which point CLKO
is held low.
3. The clock switching circuitry then waits for eight
falling edges of requested clock, after which it
switches CLKO to this new clock source.
4. The IOFS bit is set.
5. Oscillator switchover is complete.
TABLE 4-3:
Frequency
INTRC
T1OSC
INTOSC/
INTOSC
Postscaler
31.25 kHz
32.768 kHz
125 kHz - 8 MHz
INTRC/SLEEP
EC, RC
DC - 20 MHz
INTRC
(31.25 kHz)
EC, RC
DC - 20 MHz
SLEEP
INTRC
(31.25 kHz)
Note 1:
Table 4-3 shows the different delays invoked for various clock switching sequences. It also shows the
delays invoked for POR and wake-up.
OSCILLATOR DELAY EXAMPLES
Switch From Switch To
SLEEP/POR
OSCILLATOR DELAY UPON
POWER-UP, WAKE-UP AND
CLOCK SWITCHING
LP, XT, HS 32.768 kHz - 20 MHz
INTOSC/
INTOSC
Postscaler
125 kHz - 8 MHz
Oscillator Delay
Comments
Following a wake-up from SLEEP mode or
5 µs - 10 µs (approx.)
POR, CPU start-up is invoked to allow the
(1)
CPU Start-up
CPU to become ready for code execution.
1024 Clock Cycles
(OST)
4 ms
Following a change from INTRC, an OST
of 1024 cycles must occur.
Refer to Section 4.6.4 “Modifying the
IRCF bits” for further details.
The 5 µs-10 µs start-up delay is based on a 1 MHz system clock.
DS30487B-page 42
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
4.7
Power Managed Modes
4.7.1
If the system clock does not come from the INTRC
(31.25 kHz) when the SCS bits are changed, and the
IRCF bits in the OSCCON register are configured for a
frequency other than INTRC, the frequency may not be
stable immediately. The IOFS bit (OSCCON<2>) will
be set when the INTOSC or postscaler frequency is
stable, after approximately 4 ms.
RC_RUN MODE
When SCS bits are configured to run from the INTRC,
a clock transition is generated if the system clock is
not already using the INTRC. The event will clear the
OSTS bit, switch the system clock from the primary
system clock (if SCS<1:0> = 00) determined by the
value contained in the configuration bits, or from the
T1OSC (if SCS<1:0> = 01) to the INTRC clock option,
and shut down the primary system clock to conserve
power. Clock switching will not occur if the primary
system clock is already configured as INTRC.
FIGURE 4-7:
After a clock switch has been executed, the OSTS bit
is cleared, indicating a low-power mode, and the
device does not run from the primary system clock.
The internal Q clocks are held in the Q1 state until
eight falling edge clocks are counted on the INTRC
oscillator. After the eight clock periods have transpired, the clock input to the Q clocks is released and
operation resumes (see Figure 4-7).
TIMING DIAGRAM FOR XT, HS, LP, EC AND EXTRC TO RC_RUN MODE
Q1 Q2 Q3 Q4 Q1
INTOSC
Q1
TINP(1)
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
TSCS(3)
OSC1
System
Clock
TOSC(2)
TDLY(4)
SCS<1:0>
Program
Counter
Note 1:
2:
3:
4:
PC
TINP =
TOSC =
TSCS =
TDLY =
PC + 1
PC + 2
PC + 3
32 µs typical.
50 ns minimum.
8 TINP.
1 TINP.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 43
PIC16F87/88
4.7.2
SEC_RUN MODE
The core and peripherals can be configured to be
clocked by T1OSC using a 32.768 kHz crystal. The
crystal must be connected to the T1OSO and T1OSI
pins. This is the same configuration as the low-power
timer circuit (see Section 7.6 “Timer1 Oscillator”).
When SCS bits are configured to run from T1OSC, a
clock transition is generated. It will clear the OSTS bit,
switch the system clock from either the primary system
clock, or INTRC, depending on the value of SCS<1:0>
and FOSC<2:0>, to the external low-power Timer1
oscillator input (T1OSC), and shut down the primary
system clock to conserve power.
Note 1: The T1OSCEN bit must be enabled and it
is the user’s responsibility to ensure
T1OSC is stable before clock switching to
the T1OSC input clock can occur.
2: When T1OSCEN = 0, the following possible
effects result.
Original
Modified
Final
SCS<1:0> SCS<1:0>
SCS<1:0>
00
01
00 - no change
00
11
10 - INTRC
10
11
10 - no change
10
01
00 - OSC
defined by
FOSC<2:0>
A clock switching event will occur if the
final state of the SCS bits is different from
the original.
After a clock switch has been executed, the internal Q
clocks are held in the Q1 state until eight falling edge
clocks are counted on the T1OSC. After the eight
clock periods have transpired, the clock input to the Q
clocks is released and operation resumes (see
Figure 4-8). In addition, T1RUN (In T1CON) is set to
indicate that T1OSC is being used as the system
clock.
FIGURE 4-8:
TIMING DIAGRAM FOR SWITCHING TO SEC_RUN MODE
Q1 Q2 Q3 Q4 Q1
T1OSI
Q1
TT1P(1)
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
TSCS(3)
OSC1
System
Clock
TOSC(2)
TDLY(4)
SCS<1:0>
Program
Counter
Note 1:
2:
3:
4:
PC
PC +1
PC + 2
PC +3
TT1P = 30.52 µs.
TOSC = 50 ns minimum.
TSCS = 8 TT1P
TDLY = 1 TT1P.
DS30487B-page 44
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
4.7.3
SEC_RUN/RC_RUN TO PRIMARY
CLOCK SOURCE
When switching from a SEC_RUN or RC_RUN mode
back to the primary system clock, following a change
of SCS<1:0> to ‘00’, the sequence of events that take
place will depend upon the value of the FOSC bits in
the Configuration register. If the primary clock source
is configured as a crystal (HS, XT, or LP), then the
transition will take place after 1024 clock cycles. This
is necessary because the crystal oscillator had been
powered down until the time of the transition. In order
to provide the system with a reliable clock when the
changeover has occurred, the clock will not be
released to the changeover circuit until the 1024 count
has expired.
During the oscillator start-up time, the system clock
comes from the current system clock. Instruction execution and/or peripheral operation continues using the
currently selected oscillator as the CPU clock source,
until the necessary clock count has expired to ensure
that the primary system clock is stable.
To know when the OST has expired, the OSTS bit
should be monitored. OSTS = 1 indicates that the
Oscillator Start-up Timer has timed out and the system
clock comes from the primary clock source.
Following the oscillator start-up time, the internal Q
clocks are held in the Q1 state until eight falling edge
clocks are counted from the primary system clock. The
clock input to the Q clocks is then released, and operation resumes with primary system clock determined
by the FOSC bits (see Figure 4-10).
4.7.3.1
Returning to Primary Clock Source
Sequence
Changing back to the primary oscillator from
SEC_RUN or RC_RUN can be accomplished by either
changing SCS<1:0> to ‘00’, or clearing the T1OSCEN
bit in the T1CON register (if T1OSC was the secondary
clock).
The sequence of events that follows is the same for
both modes:
1.
2.
3.
4.
5.
6.
7.
If the primary system clock is configured as EC,
RC, or INTRC, then the OST time-out is
skipped. Skip to step 3.
If the primary system clock is configured as an
external oscillator (HS, XT, LP), then the OST
will be active, waiting for 1024 clocks of the
primary system clock.
On the following Q1, the device holds the
system clock in Q1.
The device stays in Q1 while eight falling edges
of the primary system clock are counted.
Once the eight counts transpire, the device
begins to run from the primary oscillator.
If the secondary clock was INTRC and the primary is not INTRC, the INTRC will be shut down
to save current, providing that the INTRC is not
being used for any other function, such as WDT,
or Fail-Safe Clock monitoring.
If the secondary clock was T1OSC, the T1OSC
will continue to run if T1OSCEN is still set,
otherwise the T1 oscillator will be shut down.
When in SEC_RUN mode, the act of clearing the
T1OSCEN bit in the T1CON register will cause
SCS<0> to be cleared, which causes the SCS<1:0>
bits to revert to ‘00’ or ‘10’, depending on what SCS<1>
is. Although the T1OSCEN bit was cleared, T1OSC will
be enabled and instruction execution will continue until
the OST time-out for the main system clock is complete. At that time, the system clock will switch from the
T1OSC to the primary clock or the INTRC. Following
this, the T1 oscillator will be shut down.
Note:
If the primary system clock is either RC or
EC, an internal delay timer (5-10 µs) will
suspend operation after exiting Secondary
Clock mode to allow the CPU to become
ready for code execution.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 45
PIC16F87/88
FIGURE 4-9:
TIMING FOR TRANSITION BETWEEN SEC_RUN/RC_RUN AND PRIMARY
CLOCK
Q4
Q1
Q2
Q3
TT1P(1) or TINP(2)
Q1
Q4
Q2 Q3 Q4 Q1 Q2 Q3 Q4
Sec. Osc
OSC1
TOST
OSC2
TOSC(3)
Primary Clock
TSCS(4)
System Clock
TDLY(5)
SCS<1:0>
OSTS
Program
Counter
Note 1:
2:
3:
4:
5:
PC
PC + 2
PC + 1
PC +3
TT1P = 30.52 µs.
TINP = 32 µs typical.
TOSC = 50 ns minimum.
TSCS = 8 TINP OR 8 TT1P.
TDLY = 1 TINP OR 1 TT1P.
DS30487B-page 46
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
4.7.3.2
Returning to Primary Oscillator with
a RESET
A RESET will clear SCS<1:0> back to ‘00’. The
sequence for starting the primary oscillator following a
RESET is the same for all forms of RESET, including
POR. There is no transition sequence from the
alternate system clock to the primary system clock on
a RESET condition. Instead, the device will reset the
state of the OSCCON register and default to the
primary system clock. The sequence of events that
take place after this will depend upon the value of the
FOSC bits in the Configuration register. If the external
oscillator is configured as a crystal (HS, XT, or LP), the
CPU will be held in the Q1 state until 1024 clock cycles
have transpired on the primary clock. This is
necessary because the crystal oscillator had been
powered down until the time of the transition.
there is no oscillator start-up time required because
the primary clock is already stable; however, there is a
delay between the wake-up event and the following
Q2. An internal delay timer of 5-10 µs will suspend
operation after the RESET to allow the CPU to
become ready for code execution. The CPU and
peripheral clock will be held in the first Q1.
The sequence of events is as follows:
1.
2.
3.
During the oscillator start-up time, instruction
execution and/or peripheral operation is suspended.
Note:
If Two-Speed Clock Start-up mode is
enabled, the INTRC will act as the system
clock until the OST timer has timed out.
4.
If the primary system clock is either RC, EC, or
INTRC, the CPU will begin operating on the first Q1
cycle following the wake-up event. This means that
FIGURE 4-10:
A device RESET is asserted from one of many
sources (WDT, BOR, MCLR, etc.).
The device resets and the CPU start-up timer is
enabled if in SLEEP mode. The device is held in
RESET until the CPU start-up time-out is
complete.
If the primary system clock is configured as an
external oscillator (HS, XT, LP), then the OST
will be active waiting for 1024 clocks of the primary system clock. While waiting for the OST,
the device will be held in RESET. The OST and
CPU start-up timers run in parallel.
After both the CPU start-up and OST timers
have timed out, the device will wait for one additional clock cycle and instruction execution will
begin.
PRIMARY SYSTEM CLOCK AFTER RESET (HS, XT, LP)
Q4
TT1P(1)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
T1OSI
OSC1
TOST
OSC2
TCPU(3)
TOSC(2)
CPU Start-up
System Clock
Peripheral
Clock
RESET
SLEEP
OSTS
Program
Counter
PC
0000h
0001h
0003h
0004h
0005h
Note 1: TT1P = 30.52 µs.
2: TOSC = 50 ns minimum.
3: TCPU = 5-10 µs (1 MHz system clock).
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 47
PIC16F87/88
FIGURE 4-11:
PRIMARY SYSTEM CLOCK AFTER RESET (EC, RC, INTRC)
TT1P(1)
Q4
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4
T1OSI
OSC1
OSC2
TCPU(2)
CPU Start-up
System Clock
MCLR
OSTS
Program
Counter
PC
0000h
0001h
0002h
0003h
0004h
Note 1: TT1P = 30.52 µs.
2: TCPU = 5 - 10 µs (1 MHz system clock).
DS30487B-page 48
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 4-4:
Current
System
Clock
CLOCK SWITCHING MODES
SCS bits <1:0>
Modified to:
Delay
OSTS
bit
IOFS T1RUN
bit
bit
New
System
Clock
Comments
LP, XT, HS,
T1OSC,
EC, RC
10
(INTRC)
FOSC<2:0> = LP,
XT or HS
8 Clocks of
INTRC
0
1(1)
0
INTRC
or
INTOSC
or
INTOSC
Postscaler
LP, XT, HS,
INTRC,
EC, RC
01
(T1OSC)
FOSC<2:0> = LP,
XT or HS
8 Clocks of
T1OSC
0
N/A
1
T1OSC
INTRC
T1OSC
00
FOSC<2:0> = EC
or
FOSC<2:0> = RC
8 Clocks of
EC
or
RC
1
N/A
0
EC
or
RC
INTRC
T1OSC
00
FOSC<2:0> = LP,
XT, HS
1024 Clocks
(OST)
+
8 Clocks of
LP, XT, HS
1
N/A
0
LP, XT, HS
During the 1024 clocks,
program execution is
clocked from the secondary oscillator until the
primary oscillator becomes
stable.
LP, XT, HS
00
(Due to RESET)
LP, XT, HS
1024 Clocks
(OST)
1
N/A
0
LP, XT, HS
When a RESET occurs,
there is no clock transition
sequence.
Instruction execution
and/or peripheral operation is suspended unless
Two-Speed Start-up mode
is enabled, after which the
INTRC will act as the
system clock until the OST
timer has expired.
The internal RC oscillator
frequency is dependant
upon the IRCF bits.
T1OSCEN bit must be
enabled.
Note 1: If the new clock source is INTOSC or INTOSC postscaler, then the IOFS bit will be set 4 ms after the clock
change.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 49
PIC16F87/88
4.7.4
EXITING SLEEP WITH AN
INTERRUPT
If SCS<1:0> = 01 or 10:
1.
Any interrupt, such as WDT or INT0, will cause the part
to leave the SLEEP mode.
The SCS bits are unaffected by a SLEEP command and
are the same before and after entering and leaving
SLEEP. The clock source used after an exit from
SLEEP is determined by the SCS bits.
4.7.4.1
The device is held in SLEEP until the CPU start-up
time-out is complete.
After the CPU start-up timer has timed out, the
device will exit SLEEP and begin instruction
execution with the selected oscillator mode.
2.
Note:
Sequence of Events
If SCS<1:0> = 00:
1.
2.
3.
The device is held in SLEEP until the CPU start-up
time-out is complete.
If the primary system clock is configured as an
external oscillator (HS, XT, LP), then the OST will
be active waiting for 1024 clocks of the primary
system clock. While waiting for the OST, the
device will be held in SLEEP unless Two-Speed
Start-up is enabled. The OST and CPU start-up
timers run in parallel. Refer to Section 15.12.3
“Two-Speed Clock Start-up Mode” for details
on Two-Speed Start-up.
After both the CPU start-up and OST timers
have timed out, the device will exit SLEEP and
begin instruction execution with the primary
clock defined by the FOSC bits.
DS30487B-page 50
Preliminary
If a user changes SCS<1:0> just before
entering SLEEP mode, the system clock
used when exiting SLEEP mode could be
different than the system clock used when
entering SLEEP mode.
As an example, if SCS<1:0> = 01 and
T1OSC is the system clock, and the
following instructions are executed:
BCF
SLEEP
OSCCON,SCS0
then a clock change event is executed. If
the primary oscillator is XT, LP, or HS, the
core will continue to run off T1OSC and
execute the SLEEP command.
When SLEEP is exited, the part will
resume operation with the primary
oscillator after the OST has expired.
 2003 Microchip Technology Inc.
PIC16F87/88
5.0
I/O PORTS
Some pins for these I/O ports are multiplexed with an
alternate function for the peripheral features on the
device. In general, when a peripheral is enabled, that
pin may not be used as a general purpose I/O pin.
Additional information on I/O ports may be found in the
PICmicro® Mid-Range Reference Manual (DS33023).
5.1
PORTA and the TRISA Register
PORTA is a 8-bit wide, bidirectional port. The corresponding data direction register is TRISA. Setting a
TRISA bit (= 1) will make the corresponding PORTA
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISA bit (= 0)
will make the corresponding PORTA pin an output (i.e.,
put the contents of the output latch on the selected pin).
Note:
On a Power-on Reset, the pins
PORTA<4:0> are configured as analog
inputs and read as ‘0’.
Reading the PORTA register, reads the status of the
pins, whereas writing to it, will write to the port latch. All
write operations are read-modify-write operations.
Therefore, a write to a port implies that the port pins are
read, this value is modified, and then written to the port
data latch.
TABLE 5-1:
Pin RA4 is multiplexed with the Timer0 module clock
input and with analog input to become the RA4/AN4/
T0CKI/C2OUT pin. The RA4/AN4/T0CKI/C2OUT pin is
a Schmitt Trigger input and full CMOS output driver.
Pin RA5 is multiplexed with the Master Clear module
input. The RA5/MCLR/VPP pin is a Schmitt Trigger
input.
Pin RA6 is multiplexed with the oscillator module input
and external oscillator output. Pin RA7 is multiplexed
with the oscillator module input and external oscillator
input. Pin RA6/OSC2/CLKO and pin RA7/OSC1/CLKI
are Schmitt Trigger inputs and full CMOS output drivers.
Pins RA<1:0> are multiplexed with analog inputs. Pins
RA<3:2> are multiplexed with analog inputs, comparator outputs, and VREF inputs. Pins RA<3:0> have TTL
inputs and full CMOS output drivers.
EXAMPLE 5-1:
INITIALIZING PORTA
BANKSEL PORTA
CLRF
PORTA
BANKSEL ANSEL
MOVLW
0x00
MOVWF
ANSEL
MOVLW
0xFF
MOVWF
TRISA
;
;
;
;
;
;
;
select bank of PORTA
Initialize PORTA by
clearing output
data latches
Select Bank of ANSEL
Configure all pins
as digital inputs
;
;
;
;
Value used to
initialize data
direction
Set RA<7:0> as inputs
PORTA FUNCTIONS
Name
Bit#
Buffer
RA0/AN0
bit 0
TTL
RA1/AN1
bit 1
TTL
Input/output or analog input.
bit 2
TTL
Input/output or analog input or VREF- or comparator VREF
output.
RA3/AN3/VREF+(2)/C1OUT
bit 3
TTL
Input/output or analog input or VREF+ or comparator output.
RA4/AN4(2)/T0CKI/C2OUT
bit 4
ST
Input/output, analog input or TMR0 external input or
comparator output.
RA5/MCLR/VPP
bit 5
ST
Input, Master Clear (Reset) or programming voltage input.
RA6/OSC2/CLKO
bit 6
ST
Input/output, connects to crystal or resonator, oscillator
output or 1/4 the frequency of OSC1, and denotes the
instruction cycle in RC mode.
RA7/OSC1/CLKI
bit 7
RA2/AN2/CVREF/VREF-(2)
Function
Input/output or analog input.
ST/CMOS(1) Input/output, connects to crystal or resonator or oscillator
input.
Legend: TTL = TTL input, ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.
2: PIC16F88 only.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 51
PIC16F87/88
TABLE 5-2:
Address
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Name
05h
PORTA
85h
TRISA
9Fh
ADCON1
9Bh
(4)
Legend:
Note 1:
2:
3:
4:
ANSEL
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Value on
all other
RESETS
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
xxxx 0000(1)
xxx0 0000(2)
uuuu 0000(1)
uuu0 0000(2)
TRISA7 TRISA6 TRISA5(3) PORTA Data Direction Register
1111 1111
1111 1111
ADFM
ADCS2
VCFG1
VCFG0
—
—
—
—
0000 ----
0000 ----
—
ANS6
ANS5
ANS4
ANS3
ANS2
ANS1
ANS0
-111 1111
-111 1111
x = unknown, u = unchanged, - = unimplemented locations read as ‘0’. Shaded cells are not used by PORTA.
This value applies only to the PIC16F87.
This value applies only to the PIC16F88.
Pin 5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
PIC16F88 device only.
FIGURE 5-1:
BLOCK DIAGRAM OF RA0/AN0:RA1/AN1 PINS
Data
Bus
D
WR
PORTA
Q
CK
VDD
VDD
P
Q
Data Latch
D
WR
TRISA
Q
I/O pin
N
CK
Q
VSS
TRIS Latch
Analog
Input Mode
TTL
Input Buffer
RD TRISA
Q
D
EN
RD PORTA
To Comparator
To A/D Module Channel Input (PIC16F88 only)
DS30487B-page 52
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-2:
Data
Bus
BLOCK DIAGRAM OF RA3/AN3/VREF+/C1OUT PIN
Comparator Mode = 110
D
Q
Comparator 1 Output
WR
PORTA
CK
VDD
VDD
Q
P
Data Latch
D
Q
RA3 pin
N
WR
TRISA
CK
Q
TRIS Latch
VSS
VSS
Analog
Input Mode
TTL
Input Buffer
RD TRISA
Q
D
EN
RD PORTA
To Comparator
To A/D Module Channel Input (PIC16F88 only)
To A/D Module Channel VREF+ Input (PIC16F88 only)
BLOCK DIAGRAM OF RA2/AN2/CVREF/VREF- PIN
FIGURE 5-3:
Data
Bus
D
Q
VDD
WR
PORTA
CK
VDD
Q
P
Data Latch
D
WR
TRISA
Q
RA2 pin
N
CK
Q
VSS
Analog
Input Mode
TRIS Latch
TTL
Input Buffer
RD TRISA
Q
D
EN
RD PORTA
To Comparator
To A/D Module VREF- (PIC16F88 only)
To A/D Module Channel Input (PIC16F88 only)
CVROE
CVREF
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 53
PIC16F87/88
FIGURE 5-4:
Data
Bus
BLOCK DIAGRAM OF RA4/AN4/T0CKI/C2OUT PIN
Comparator Mode = 011, 101, 110
D
Q
Comparator 2 Output
WR
PORTA
VDD
1
CK
Q
0
Data Latch
D
VDD
P
Q
RA4 pin
N
WR
TRISA
CK
Q
VSS
Analog
Input Mode
TRIS Latch
Schmitt Trigger
Input Buffer
RD TRISA
Q
D
EN
RD PORTA
TMR0 Clock Input
To A/D Module Channel Input (PIC16F88 only)
FIGURE 5-5:
BLOCK DIAGRAM OF RA5/MCLR/VPP PIN
MCLRE
MCLR Circuit
Schmitt Trigger
Buffer
MCLR Filter
Data Bus
RA5/MCLR/VPP pin
Schmitt Trigger
Input Buffer
RD TRIS VSS
Q
VSS
D
EN
MCLRE
RD Port
DS30487B-page 54
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-6:
BLOCK DIAGRAM OF RA6/OSC2/CLKO PIN
From OSC1
CLKO (FOSC/4)
Oscillator
Circuit
VDD
VDD
P
RA6/OSC2/CLKO pin
Data
Bus
WR
PORTA
D
CK
VSS
N
(FOSC = 1x1)
Q
VSS
VDD
Q
P
Data Latch
D
WR
TRISA
Q
N
CK
Q
(FOSC = 1x0, 011)
TRIS Latch
VSS
Schmitt Trigger
Input Buffer
RD TRISA
Q
D
EN
RD PORTA
(FOSC = 1x0, 011)
Note 1: I/O pins have protection diodes to VDD and VSS.
2: CLKO signal is 1/4 of the FOSC frequency.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 55
PIC16F87/88
FIGURE 5-7:
BLOCK DIAGRAM OF RA7/OSC1/CLKI PIN
From OSC2
Oscillator
Circuit
VDD
(FOSC = 011)
Data
Bus
D
WR
PORTA
CK
Q
VDD
Q
P
RA7/OSC1/CLKI pin(1)
VSS
Data Latch
D
WR
TRISA
Q
N
CK
Q
FOSC = 10x
TRIS Latch
VSS
Schmitt Trigger
Input Buffer
RD TRISA
Q
D
EN
FOSC = 10x
RD PORTA
Note 1: I/O pins have protection diodes to VDD and VSS.
DS30487B-page 56
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
5.2
PORTB and the TRISB Register
PORTB is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISB. Setting a
TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISB bit (= 0)
will make the corresponding PORTB pin an output (i.e.,
put the contents of the output latch on the selected pin).
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION<7>). The weak
pull-up is automatically turned off when the port pin is
configured as an output. The pull-ups are disabled on a
Power-on Reset.
Four of PORTB’s pins, RB7:RB4, have an interrupt-onchange feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupton-change comparison). The input pins (of RB7:RB4)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB7:RB4
are OR’d together to generate the RB port change
interrupt with flag bit RBIF (INTCON<0>).
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
RB0/INT is an external interrupt input pin and is
configured using the INTEDG bit (OPTION<6>).
PORTB is multiplexed with several peripheral functions
(see Table 5-3). PORTB pins have Schmitt Trigger
input buffers.
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTB pin. Some
peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to
make a pin an input. Since the TRIS bit override is in
effect while the peripheral is enabled, read-modifywrite instructions (BSF, BCF, XORWF) with TRISB as
destination should be avoided. The user should refer to
the corresponding peripheral section for the correct
TRIS bit settings.
This interrupt can wake the device from SLEEP. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
Any read or write of PORTB. This will end the
mismatch condition.
Clear flag bit RBIF.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 57
PIC16F87/88
TABLE 5-3:
PORTB FUNCTIONS
Name
Bit#
RB0/INT/CCP1
bit 0
TTL/ST(1) Input/output pin or external interrupt input.
Capture input/Compare output/PWM output pin.
Internal software programmable weak pull-up.
RB1/SDI/SDA
bit 1
TTL/ST(5) Input/output pin, SPI data input pin or I2C data I/O pin.
Internal software programmable weak pull-up.
RB2/SDO/RX/DT
bit 2
TTL/ST(4) Input/output pin, SPI data output pin.
USART asynchronous receive or synchronous data.
Internal software programmable weak pull-up.
RB3/PGM/CCP1(3)
bit 3
TTL/ST(2) Input/output pin, programming in LVP mode or Capture input/Compare
output/PWM output pin. Internal software programmable weak pull-up.
RB4/SCK/SCL
bit 4
TTL/ST(5) Input/output pin or SPI and I2C clock pin (with interrupt-on-change).
Internal software programmable weak pull-up.
RB5/SS/TX/CK
bit 5
RB6/AN5/PGC/T1OSO/
T1CKI
bit 6
TTL/ST(2) Input/output pin, analog input(6), serial programming clock
(with interrupt-on-change), Timer1 oscillator output pin or Timer1 clock
input pin. Internal software programmable weak pull-up.
RB7/AN6/PGD/T1OSI
bit 7
TTL/ST(2) Input/output pin, analog input(6), serial programming data (with
interrupt-on-change) or Timer1 oscillator input pin.
Internal software programmable weak pull-up.
Legend:
Note 1:
2:
3:
4:
5:
6:
Buffer
TTL
Function
Input/output pin or SPI slave select pin (with interrupt-on-change).
USART asynchronous transmit or synchronous clock.
Internal software programmable weak pull-up.
TTL = TTL input, ST = Schmitt Trigger input
This buffer is a Schmitt Trigger input when configured as the external interrupt.
This buffer is a Schmitt Trigger input when used in Serial Programming mode.
Low-Voltage ICSP Programming (LVP) is enabled by default, which disables the RB3 I/O function. LVP
must be disabled to enable RB3 as an I/O pin and allow maximum compatibility to the other 18-pin
mid-range devices.
This buffer is a Schmitt Trigger input when configured for CCP or SSP mode.
This buffer is a Schmitt Trigger input when configured for SPI or I2C mode.
PIC16F88 only.
TABLE 5-4:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3 Bit 2 Bit 1 Bit 0
Value on
POR, BOR
Value on
all other
RESETS
06h, 106h
PORTB
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx
uuuu uuuu
1111 1111
1111 1111
T0CS T0SE
PSA
PS2
PS1
PS0
1111 1111
1111 1111
ANS5
ANS3 ANS2 ANS1 ANS0
-111 1111
-111 1111
86h, 186h
TRISB
PORTB Data Direction Register
81h, 181h
OPTION
RBPU
INTEDG
9Bh
ANSEL(1)
—
ANS6
ANS4
Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB.
Note 1: PIC16F88 device only.
DS30487B-page 58
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-8:
BLOCK DIAGRAM OF RB0 PIN
CCP1<M3:M0> = 1000, 1001, 11xx and CCPMX = 1
CCP
0
1
CCP1<M3:M0> = 000
VDD
RBPU(2)
Data Bus
WR PORTB
P Weak
Pull-up
Data Latch
D
Q
I/O pin(1)
CK
TRIS Latch
D
Q
WR TRISB
TTL
Input
Buffer
CK
RD TRISB
Q
RD PORTB
D
EN
To INT0 or CCP
RD PORTB
Note 1: I/O pins have diode protection to VDD and VSS.
2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 59
PIC16F87/88
FIGURE 5-9:
BLOCK DIAGRAM OF RB1 PIN
I2C™ Mode
PORT/SSPEN Select
SDA Output
1
0
VDD
RBPU(2)
Data Bus
WR
PORTB
Weak
P Pull-up
VDD
Data Latch
D
Q
P
CK
N
I/O pin(1)
VSS
TRIS Latch
D
Q
WR
TRISB
CK
Q
RD TRISB
TTL
Input
Buffer
SDA Drive
Q
D
RD PORTB
EN
SDA(3)
Schmitt Trigger
Buffer
RD PORTB
SDI
Note 1:
2:
3:
DS30487B-page 60
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
The SDA Schmitt conforms to the I2C specification.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-10:
BLOCK DIAGRAM OF RB2 PIN
SSPEN
SDO
1
0
SSPEN + SPEN
SPEN
DT
1
0
VDD
RBPU(2)
Weak
P Pull-up
VDD
Data Latch
Data Bus
WR PORTB
D
P
Q
CK
I/O pin(1)
N
VSS
TRIS Latch
D
Q
WR TRISB
CK
Q
RD TRISB
TTL
Input
Buffer
DT Drive
Q
D
RD PORTB
EN
Schmitt Trigger
Buffer
RD PORTB
RX/DT
Note 1:
2:
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 61
PIC16F87/88
FIGURE 5-11:
BLOCK DIAGRAM OF RB3 PIN
CCP1<M3:M0> = 1000, 1001, 11xx and CCPMX = 0
CCP1<M3:M0> = 0100, 0101, 0110, 0111 and CCPMX = 0
CCP
0
or LVP = 1
1
VDD
RBPU(2)
Data Bus
WR
PORTB
Weak
P Pull-up
Data Latch
D
Q
I/O pin(1)
CK
TRIS Latch
D
Q
WR
TRISB
TTL
Input
Buffer
CK
RD TRISB
D
Q
RD PORTB
EN
To PGM or CCP
RD PORTB
Note 1:
2:
DS30487B-page 62
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-12:
BLOCK DIAGRAM OF RB4 PIN
PORT/SSPEN
SCK/SCL
1
0
VDD
RBPU(2)
Weak
P Pull-up
VDD
SCL Drive
Data Bus
WR
PORTB
P
Data Latch
D
Q
I/O pin(1)
N
CK
TRIS Latch
D
WR
TRISB
VSS
Q
CK
TTL
Input
Buffer
RD TRISB
Latch
Q
D
EN
RD PORTB
Q1
Set RBIF
Q
From Other
RB7:RB4 pins
D
RD PORTB
EN
Q3
SCK
SCL(3)
Note 1:
2:
3:
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
The SCL Schmitt conforms to the I2C™ specification.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 63
PIC16F87/88
FIGURE 5-13:
BLOCK DIAGRAM OF RB5 PIN
RBPU(2)
VDD
PORT/SSPEN
Weak
P Pull-up
Data Bus
WR
PORTB
Data Latch
D
Q
I/O pin(1)
CK
TRIS Latch
D
WR
TRISB
Q
CK
TTL
Input
Buffer
RD TRISB
Latch
Q
D
EN
RD PORTB
Q1
Set RBIF
Q
From Other
RB7:RB4 pins
D
RD PORTB
EN
Q3
SS/TX/CK
Note 1:
2:
DS30487B-page 64
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 5-14:
BLOCK DIAGRAM OF RB6 PIN
Analog
Input Mode
VDD
RBPU(2)
Weak
P Pull-up
Data Latch
Data Bus
WR PORTB
D
Q
I/O pin(1)
CK
TRIS Latch
D
WR TRISB
Q
CK
Analog
Input Mode
TTL
Input Buffer
RD TRISB
T1OSCEN/ICD/PROG
Mode
Latch
Q
D
EN
RD PORTB
Q1
Set RBIF
Q
From other
RB7:RB4 pins
D
RD PORTB
EN
Q3
PGC/T1CKI
From T1OSCO Output
To A/D Module Channel Input (PIC16F88 only)
Note 1:
2:
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 65
PIC16F87/88
FIGURE 5-15:
BLOCK DIAGRAM OF RB7 PIN
PORT/Program Mode/ICD
PGD
1
0
Analog Input Mode
VDD
RBPU(2)
Weak
P Pull-up
Data Latch
Data Bus
D
WR
PORTB
Q
I/O pin(1)
CK
TRIS Latch
D
WR
TRISB
Q
0
CK
RD TRISB
T1OSCEN
1
T1OSCEN
Analog
Input Mode
PGD DRVEN
TTL
Input Buffer
Latch
Q
D
EN
RD PORTB
Q1
Set RBIF
Q
From Other
RB7:RB4 pins
D
RD PORTB
EN
Q3
PGD
To T1OSCI Input
To A/D Module Channel Input (PIC16F88 only)
Note 1:
2:
DS30487B-page 66
I/O pins have diode protection to VDD and VSS.
To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
6.0
TIMER0 MODULE
increment is inhibited for the following two instruction
cycles. The user can work around this by writing an
adjusted value to the TMR0 register.
The Timer0 module timer/counter has the following
features:
•
•
•
•
•
•
Counter mode is selected by setting bit T0CS
(OPTION<5>). In Counter mode, Timer0 will increment,
either on every rising or falling edge of pin RA4/T0CKI.
The incrementing edge is determined by the Timer0
Source Edge Select bit, T0SE (OPTION<4>). Clearing
bit T0SE selects the rising edge. Restrictions on the
external clock input are discussed in detail in Section 6.3
“Using Timer0 with an External Clock”.
8-bit timer/counter
Readable and writable
8-bit software programmable prescaler
Internal or external clock select
Interrupt on overflow from FFh to 00h
Edge select for external clock
Additional information on the Timer0 module is
available in the PICmicro® Mid-Range MCU Family
Reference Manual (DS33023).
The prescaler is mutually, exclusively shared between
the Timer0 module and the Watchdog Timer. The
prescaler is not readable or writable. Section 6.4
“Prescaler” details the operation of the prescaler.
Figure 6-1 is a block diagram of the Timer0 module and
the prescaler shared with the WDT.
6.2
6.1
Timer0 Operation
The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit
TMR0IF (INTCON<2>). The interrupt can be masked
by clearing bit TMR0IE (INTCON<5>). Bit TMR0IF
must be cleared in software by the Timer0 module
Interrupt Service Routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor
from SLEEP, since the timer is shut-off during SLEEP.
Timer0 operation is controlled through the OPTION
register (see Register 2-2). Timer mode is selected by
clearing bit T0CS (OPTION<5>). In Timer mode, the
Timer0 module will increment every instruction cycle
(without prescaler). If the TMR0 register is written, the
FIGURE 6-1:
Timer0 Interrupt
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
CLKO (= FOSC/4)
Data Bus
0
RA4/T0CKI
pin
8
M
U
X
1
M
U
X
0
1
Sync
2
Cycles
TMR0 reg
T0SE
T0CS
Set Flag bit TMR0IF
on Overflow
PSA
Prescaler
0
WDT Timer
31.25 kHz
16-bit
Prescaler
1
8-bit Prescaler
M
U
X
8
8 - to - 1 MUX
WDT Enable bit
PS2:PS0
PSA
1
0
MUX
PSA
WDT
Time-out
Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION<5:0>).
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 67
PIC16F87/88
6.3
Using Timer0 with an External
Clock
Note:
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI, with the internal phase clocks, is accomplished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks. Therefore, it is
necessary for T0CKI to be high for at least 2 TOSC (and
a small RC delay of 20 ns) and low for at least 2 TOSC
(and a small RC delay of 20 ns). Refer to the electrical
specification of the desired device.
6.4
Prescaler
There is only one prescaler available, which is mutually
exclusively shared between the Timer0 module and the
Watchdog Timer. A prescaler assignment for the
Timer0 module means that the prescaler cannot be
used by the Watchdog Timer, and vice versa. This
prescaler is not readable or writable (see Figure 6-1).
REGISTER 6-1:
Although the prescaler can be assigned to
either the WDT or Timer0, but not both, a
new divide counter is implemented in the
WDT circuit to give multiple WDT time-out
selections. This allows TMR0 and WDT to
each have their own scaler. Refer to
Section 15.12 “Watchdog Timer (WDT)”
for further details.
The PSA and PS2:PS0 bits (OPTION<3:0>) determine
the prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF 1, MOVWF 1,
BSF 1,x....etc.) will clear the prescaler. When assigned
to WDT, a CLRWDT instruction will clear the prescaler
along with the Watchdog Timer. The prescaler is not
readable or writable.
Note:
Writing to TMR0, when the prescaler is
assigned to Timer0, will clear the
prescaler count but will not change the
prescaler assignment.
OPTION_REG REGISTER (ADDRESS 81h, 181h)
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
RBPU
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
bit 7
bit 0
bit 7
RBPU: PORTB Pull-up Enable bit
bit 6
INTEDG: Interrupt Edge Select bit
bit 5
T0CS: TMR0 Clock Source Select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKO)
bit 4
T0SE: TMR0 Source Edge Select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
bit 3
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
bit 2-0
PS<2:0>: Prescaler Rate Select bits
Bit Value TMR0 Rate WDT Rate
1:2
000
1:1
1:4
001
1:2
1:8
010
1:4
1 : 16
011
1:8
1 : 32
100
1 : 16
1 : 64
101
1 : 32
1 : 128
110
1 : 64
1 : 256
111
1 : 128
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Note:
DS30487B-page 68
x = Bit is unknown
To avoid an unintended device RESET, the instruction sequence shown in the
PICmicro® Mid-Range MCU Family Reference Manual (DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This
sequence must be followed even if the WDT is disabled.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
EXAMPLE 6-1:
CHANGING THE PRESCALER ASSIGNMENT FROM WDT TO TIMER0
CLRWDT
BANKSEL OPTION
MOVLW
b'xxxx0xxx'
MOVWF
OPTION
TABLE 6-1:
Address
01h,101h
81h,181h
Clear WDT and prescaler
Select Bank of OPTION
Select TMR0, new prescale
value and clock source
REGISTERS ASSOCIATED WITH TIMER0
Name
TMR0
0Bh,8Bh,
INTCON
10Bh,18Bh
Legend:
;
;
;
;
OPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Timer0 Module Register
Value on
POR, BOR
Value on
all other
RESETS
xxxx xxxx
uuuu uuuu
GIE
PEIE
TMR0IE
INTE
RBIE TMR0IF INTF RBIF 0000 000x
0000 000u
RBPU
INTEDG
T0CS
T0SE
PSA
1111 1111
PS2
PS1
PS0
1111 1111
x = unknown, u = unchanged, - = unimplemented locations read as ‘0’. Shaded cells are not used by Timer0.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 69
PIC16F87/88
NOTES:
DS30487B-page 70
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
7.0
TIMER1 MODULE
7.1
The Timer1 module is a 16-bit timer/counter consisting
of two 8-bit registers (TMR1H and TMR1L), which are
readable and writable. The TMR1 register pair
(TMR1H:TMR1L) increments from 0000h to FFFFh
and rolls over to 0000h. The TMR1 interrupt, if enabled,
is generated on overflow, which is latched in interrupt
flag bit, TMR1IF (PIR1<0>). This interrupt can be
enabled/disabled by setting/clearing TMR1 interrupt
enable bit, TMR1IE (PIE1<0>).
The Timer1 oscillator can be used as a secondary clock
source in Low-power modes. When the T1RUN bit is
set along with SCS<1:0> = 01, the Timer1 oscillator is
providing the system clock. If the Fail-Safe Clock Monitor is enabled, and the Timer1 oscillator fails while providing the system clock, polling the T1RUN bit will
indicate whether the clock is being provided by the
Timer1 oscillator or another source.
Timer1 can also be used to provide Real-Time Clock
(RTC) functionality to applications with only a minimal
addition of external components and code overhead.
Timer1 Operation
Timer1 can operate in one of three modes:
• as a Timer
• as a Synchronous Counter
• as an Asynchronous Counter
The operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>).
In Timer mode, Timer1 increments every instruction
cycle. In Counter mode, it increments on every rising
edge of the external clock input.
Timer1 can be enabled/disabled by setting/clearing
control bit, TMR1ON (T1CON<0>).
Timer1 also has an internal “RESET input”. This
RESET can be generated by the CCP1 module as
the special event trigger (see Section 9.1 “Capture
Mode”). Register 7-1 shows the Timer1 Control
register.
When the Timer1 oscillator is enabled (T1OSCEN is
set), the RB6/T1OSO/T1CKI/PGC and RB7/T1OSI/
PGD pins become inputs. That is, the TRISB<7:6>
value is ignored and these pins read as ‘0’.
Additional information on timer modules is available in
the PICmicro® Mid-Range MCU Family Reference
Manual (DS33023).
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 71
PIC16F87/88
REGISTER 7-1:
T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h)
U-0
R-0
R/W-0
R/W-0
—
T1RUN
T1CKPS1
T1CKPS0
R/W-0
R/W-0
R/W-0
R/W-0
T1OSCEN T1SYNC TMR1CS TMR1ON
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6
T1RUN: Timer1 System Clock Status bit
1 = System clock is derived from Timer1 oscillator
0 = System clock is derived from another source
bit 5-4
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 3
T1OSCEN: Timer1 Oscillator Enable Control bit
1 = Oscillator is enabled
0 = Oscillator is shut-off (the oscillator inverter is turned off to eliminate power drain)
bit 2
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1:
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
bit 1
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RB6/AN5/PGC/T1OSO/T1CKI (on the rising edge)
0 = Internal clock (FOSC/4)
bit 0
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Legend:
DS30487B-page 72
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
7.2
Timer1 Operation in Timer Mode
7.4
Timer mode is selected by clearing the TMR1CS
(T1CON<1>) bit. In this mode, the input clock to the
timer is FOSC/4. The synchronize control bit, T1SYNC
(T1CON<2>), has no effect since the internal clock is
always in sync.
7.3
Counter mode is selected by setting bit TMR1CS. In
this mode, the timer increments on every rising edge of
clock input on pin RB7/AN6/PGD/T1OSI, when bit
T1OSCEN is set, or on pin RB6/AN5/PGC/T1OSO/
T1CKI, when bit T1OSCEN is cleared.
Timer1 Counter Operation
If T1SYNC is cleared, then the external clock input is
synchronized with internal phase clocks. The synchronization is done after the prescaler stage. The
prescaler stage is an asynchronous ripple counter.
Timer1 may operate in Asynchronous or Synchronous
mode, depending on the setting of the TMR1CS bit.
When Timer1 is being incremented via an external
source, increments occur on a rising edge. After Timer1
is enabled in Counter mode, the module must first have
a falling edge before the counter begins to increment.
FIGURE 7-1:
Timer1 Operation in Synchronized
Counter Mode
In this configuration, during SLEEP mode, Timer1 will
not increment even if the external clock is present,
since the synchronization circuit is shut-off. The
prescaler, however, will continue to increment.
TIMER1 INCREMENTING EDGE
T1CKI
(Default High)
T1CKI
(Default Low)
Note: Arrows indicate counter increments.
FIGURE 7-2:
TIMER1 BLOCK DIAGRAM
Set Flag bit
TMR1IF on
Overflow
0
TMR1
TMR1H
Synchronized
Clock Input
TMR1L
1
TMR1ON
On/Off
T1SYNC
T1OSC
1
T1OSO/T1CKI
T1OSI
T1OSCEN FOSC/4
Enable
Internal
Oscillator(1) Clock
Prescaler
1, 2, 4, 8
Synchronize
det
0
2
T1CKPS1:T1CKPS0
TMR1CS
Q Clock
Note 1: When the T1OSCEN bit is cleared, the inverter is turned off. This eliminates power drain.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 73
PIC16F87/88
7.5
7.5.1
Timer1 Operation in
Asynchronous Counter Mode
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and can
generate an interrupt on overflow that will wake-up the
processor. However, special precautions in software
are needed to read/write the timer (Section 7.5.1
“Reading and Writing Timer1 in Asynchronous
Counter Mode”).
In Asynchronous Counter mode, Timer1 cannot be
used as a time base for capture or compare operations.
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
Reading TMR1H or TMR1L, while the timer is running
from an external asynchronous clock, will ensure a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself, poses certain problems, since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write contention may occur by writing to the timer registers while the
register is incrementing. This may produce an
unpredictable value in the timer register.
Reading the 16-bit value requires some care. The
example codes provided in Example 7-1 and
Example 7-2 demonstrate how to write to and read
Timer1 while it is running in Asynchronous mode.
EXAMPLE 7-1:
WRITING A 16-BIT FREE-RUNNING TIMER
; All interrupts are disabled
CLRF
TMR1L
; Clear Low byte, Ensures no rollover into TMR1H
MOVLW
HI_BYTE
; Value to load into TMR1H
MOVWF
TMR1H, F
; Write High byte
MOVLW
LO_BYTE
; Value to load into TMR1L
MOVWF
TMR1H, F
; Write Low byte
; Re-enable the Interrupt (if required)
CONTINUE
; Continue with your code
EXAMPLE 7-2:
READING A 16-BIT FREE-RUNNING TIMER
; All interrupts are disabled
MOVF
TMR1H, W
; Read high byte
MOVWF
TMPH
MOVF
TMR1L, W
; Read low byte
MOVWF
TMPL
MOVF
TMR1H, W
; Read high byte
SUBWF
TMPH, W
; Sub 1st read with 2nd read
BTFSC
STATUS,Z
; Is result = 0
GOTO
CONTINUE
; Good 16-bit read
; TMR1L may have rolled over between the read of the high and low bytes.
; Reading the high and low bytes now will read a good value.
MOVF
TMR1H, W
; Read high byte
MOVWF
TMPH
MOVF
TMR1L, W
; Read low byte
MOVWF
TMPL
; Re-enable the Interrupt (if required)
CONTINUE
; Continue with your code
DS30487B-page 74
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
7.6
Timer1 Oscillator
7.7
A crystal oscillator circuit is built between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscillator is a low-power oscillator rated up to 32.768 kHz. It
will continue to run during all Power Managed modes.
It is primarily intended for a 32 kHz crystal. The circuit
for a typical LP oscillator is shown in Figure 7-3.
Table 7-1 shows the capacitor selection for the Timer1
oscillator.
The user must provide a software time delay to ensure
proper oscillator start-up.
FIGURE 7-3:
EXTERNAL
COMPONENTS FOR THE
TIMER1 LP OSCILLATOR
C1
33 pF
Timer1 Oscillator Layout
Considerations
The Timer1 oscillator circuit draws very little power during operation. Due to the low-power nature of the oscillator, it may also be sensitive to rapidly changing
signals in close proximity.
The oscillator circuit, shown in Figure 7-3, should be
located as close as possible to the microcontroller.
There should be no circuits passing within the oscillator
circuit boundaries other than VSS or VDD.
If a high-speed circuit must be located near the oscillator, a grounded guard ring around the oscillator circuit,
as shown in Figure 7-4, may be helpful when used on
a single-sided PCB, or in addition to a ground plane.
FIGURE 7-4:
PIC16F87/88
OSCILLATOR CIRCUIT
WITH GROUNDED
GUARD RING
T1OSI
VSS
XTAL
32.768 kHz
OSC1
OSC2
T1OSO
C2
33 pF
Note:
See the Notes with Table 7-1 for additional
information about capacitor selection.
RB7
RB6
TABLE 7-1:
CAPACITOR SELECTION FOR
THE TIMER1 OSCILLATOR
Osc Type
Freq
C1
C2
LP
32 kHz
33 pF
33 pF
RB5
7.8
Note 1: Microchip suggests this value as a starting
point in validating the oscillator circuit.
2: Higher capacitance increases the stability
of the oscillator, but also increases the
start-up time.
3: Since each resonator/crystal has its own
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
values
of
external
components.
4: Capacitor values are for design guidance
only.
Resetting Timer1 Using a CCP
Trigger Output
If the CCP1 module is configured in Compare mode to
generate
a
“special
event
trigger"
signal
(CCP1M3:CCP1M0 = 1011), the signal will reset
Timer1 and start an A/D conversion (if the A/D module
is enabled).
Note:
The special event triggers from the CCP1
module will not set interrupt flag bit
TMR1IF (PIR1<0>).
Timer1 must be configured for either Timer or Synchronized Counter mode to take advantage of this feature.
If Timer1 is running in Asynchronous Counter mode,
this RESET operation may not work.
In the event that a write to Timer1 coincides with a
special event trigger from CCP1, the write will take
precedence.
In this mode of operation, the CCPR1H:CCPR1L register pair effectively becomes the period register for
Timer1.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 75
PIC16F87/88
7.9
Resetting Timer1 Register Pair
(TMR1H, TMR1L)
7.11
TMR1H and TMR1L registers are not reset to 00h on a
POR, or any other RESET, except by the CCP1 special
event triggers.
T1CON register is reset to 00h on a Power-on Reset or
a Brown-out Reset, which shuts off the timer and
leaves a 1:1 prescale. In all other RESETS, the register
is unaffected.
7.10
Timer1 Prescaler
The prescaler counter is cleared on writes to the
TMR1H or TMR1L registers.
Using Timer1 as a Real-Time
Clock
Adding an external LP oscillator to Timer1 (such as the
one described in Section 7.6 “Timer1 Oscillator”,
above), gives users the option to include RTC functionality to their applications. This is accomplished with an
inexpensive watch crystal to provide an accurate time
base, and several lines of application code to calculate
the time. When operating in SLEEP mode and using a
battery or super capacitor as a power source, it can
completely eliminate the need for a separate RTC
device and battery backup.
The application code routine, RTCisr, shown in
Example 7-3, demonstrates a simple method to increment a counter at one-second intervals using an Interrupt Service Routine. Incrementing the TMR1 register
pair to overflow triggers the interrupt and calls the routine, which increments the seconds counter by one;
additional counters for minutes and hours are
incremented as the previous counter overflow.
Since the register pair is 16-bits wide, counting up to
overflow the register directly from a 32.768 kHz clock
would take 2 seconds. To force the overflow at the
required one-second intervals, it is necessary to preload it; the simplest method is to set the MSbit of
TMR1H with a BSF instruction. Note that the TMR1L
register is never pre-loaded or altered; doing so may
introduce cumulative error over many cycles.
For this method to be accurate, Timer1 must operate in
Asynchronous mode, and the Timer1 overflow interrupt
must be enabled (PIE1<0> = 1), as shown in the routine, RTCinit. The Timer1 oscillator must also be
enabled and running at all times.
DS30487B-page 76
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
EXAMPLE 7-3:
RTCinit
BANKSEL
MOVLW
MOVWF
CLRF
MOVLW
MOVWF
CLRF
CLRF
MOVLW
MOVWF
BANKSEL
BSF
RETURN
BANKSEL
BSF
BCF
INCF
MOVF
SUBLW
BTFSS
RETURN
CLRF
INCF
MOVF
SUBLW
BTFSS
RETURN
CLRF
INCF
MOVF
SUBLW
BTFSS
RETURN
CLRF
RETURN
RTCisr
TABLE 7-2:
Address
IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE
TMR1H
0x80
TMR1H
TMR1L
b’00001111’
T1CON
secs
mins
.12
hours
PIE1
PIE1, TMR1IE
TMR1H
TMR1H,7
PIR1,TMR1IF
secs,F
secs,w
.60
STATUS,Z
seconds
mins,f
mins,w
.60
STATUS,Z
mins
hours,f
hours,w
.24
STATUS,Z
hours
; Preload TMR1 register pair
; for 1 second overflow
; Configure for external clock,
; Asynchronous operation, external oscillator
; Initialize timekeeping registers
; Enable Timer1 interrupt
; Preload for 1 sec overflow
; Clear interrupt flag
; Increment seconds
;
;
;
;
60 seconds elapsed?
No, done
Clear seconds
Increment minutes
;
;
;
;
60 seconds elapsed?
No, done
Clear minutes
Increment hours
;
;
;
;
24 hours elapsed?
No, done
Clear hours
Done
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Name
0Bh, 8Bh, INTCON
10Bh, 18Bh
Value on
all other
RESETS
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF -000 0000 -000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE -000 0000 -000 0000
0Eh
TMR1L
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
xxxx xxxx uuuu uuuu
0Fh
TMR1H
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
xxxx xxxx uuuu uuuu
10h
T1CON
Legend:
—
T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON -000 0000 -uuu uuuu
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the Timer1 module.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 77
PIC16F87/88
NOTES:
DS30487B-page 78
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
8.0
TIMER2 MODULE
8.1
Timer2 is an 8-bit timer with a prescaler and a
postscaler. It can be used as the PWM time base for the
PWM mode of the CCP1 module. The TMR2 register is
readable and writable, and is cleared on any device
RESET.
The input clock (FOSC/4) has a prescale option of 1:1,
1:4
or
1:16,
selected
by
control
bits
T2CKPS1:T2CKPS0 (T2CON<1:0>).
The Timer2 module has an 8-bit period register, PR2.
Timer2 increments from 00h until it matches PR2 and
then resets to 00h on the next increment cycle. PR2 is
a readable and writable register. The PR2 register is
initialized to FFh upon RESET.
The match output of TMR2 goes through a 4-bit
postscaler (which gives a 1:1 to 1:16 scaling inclusive)
to generate a TMR2 interrupt (latched in flag bit
TMR2IF (PIR1<1>)).
Timer2 Prescaler and Postscaler
The prescaler and postscaler counters are cleared
when any of the following occurs:
• A write to the TMR2 register
• A write to the T2CON register
• Any device RESET (Power-on Reset, MCLR,
WDT Reset, or Brown-out Reset)
TMR2 is not cleared when T2CON is written.
8.2
Output of TMR2
The output of TMR2 (before the postscaler) is fed to the
Synchronous Serial Port module, which optionally uses
it to generate a shift clock.
FIGURE 8-1:
Sets Flag
bit TMR2IF
TIMER2 BLOCK DIAGRAM
TMR2
Output(1)
Timer2 can be shut-off by clearing control bit TMR2ON
(T2CON<2>) to minimize power consumption.
RESET
TMR2 reg
Register 8-1 shows the Timer2 Control register.
Postscaler
1:1 to 1:16
Additional information on timer modules is available in
the PICmicro® Mid-Range MCU Family Reference
Manual (DS33023).
4
EQ
Comparator
Prescaler
1:1, 1:4, 1:16
FOSC/4
2
PR2 reg
Note 1: TMR2 register output can be software selected
by the SSP module as a baud clock.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 79
PIC16F87/88
REGISTER 8-1:
T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h)
U-0
—
R/W-0
R/W-0
TOUTPS3 TOUTPS2
R/W-0
R/W-0
TOUTPS1
R/W-0
R/W-0
R/W-0
TOUTPS0 TMR2ON T2CKPS1 T2CKPS0
bit 7
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6-3
TOUTPS<3:0>: Timer2 Output Postscale Select bits
0000 = 1:1 Postscale
0001 = 1:2 Postscale
0010 = 1:3 Postscale
•
•
•
1111 = 1:16 Postscale
bit 2
TMR2ON: Timer2 On bit
1 = Timer2 is on
0 = Timer2 is off
bit 1-0
T2CKPS<1:0>: Timer2 Clock Prescale Select bits
00 = Prescaler is 1
01 = Prescaler is 4
1x = Prescaler is 16
Legend:
TABLE 8-1:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Value on
all other
RESETS
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
0Bh, 8Bh, INTCON GIE
10Bh, 18Bh
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
Address
Name
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF -000 0000 -000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE -000 0000 -000 0000
11h
TMR2
Timer2 Module Register
—
0000 0000 0000 0000
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
12h
T2CON
92h
PR2
Legend:
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.
DS30487B-page 80
Timer2 Period Register
1111 1111 1111 1111
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
9.0
CAPTURE/COMPARE/PWM
(CCP) MODULE
The CCP module’s input/output pin (CCP1) can be
configured as RB0 or RB3. This selection is set in bit 12
(CCPMX) of the configuration word.
The Capture/Compare/PWM (CCP) module contains a
16-bit register that can operate as a:
• 16-bit Capture register
• 16-bit Compare register
• PWM Master/Slave Duty Cycle register.
Table 9-1 shows the timer resources of the CCP
module modes.
Additional information on the CCP module is available
in the PICmicro® Mid-Range MCU Reference Manual,
(DS33023) and in Application Note AN594, “Using the
CCP Modules” (DS00594).
TABLE 9-1:
Capture/Compare/PWM Register1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and
CCPR1H (high byte). The CCP1CON register controls
the operation of CCP1. The special event trigger is
generated by a compare match which will reset Timer1
and start an A/D conversion (if the A/D module is
enabled).
REGISTER 9-1:
CCP MODE - TIMER
RESOURCE
CCP Mode
Timer Resource
Capture
Compare
PWM
Timer1
Timer1
Timer2
CCP1CON: CAPTURE/COMPARE/PWM CONTROL REGISTER 1 (ADDRESS 17h)
U-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
—
—
CCP1X
CCP1Y
CCP1M3
CCP1M2
CCP1M1
CCP1M0
bit 7
bit 0
bit 7-6
Unimplemented: Read as ‘0’
bit 5-4
CCP1X:CCP1Y: PWM Least Significant bits
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL.
bit 3-0
CCP1M<3:0>: CCP1 Mode Select bits
0000 = Capture/Compare/PWM disabled (resets CCP1 module)
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, set output on match (CCP1IF bit is set)
1001 = Compare mode, clear output on match (CCP1IF bit is set)
1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is
unaffected)
1011 = Compare mode, trigger special event (CCP1IF bit is set, CCP1 pin is unaffected); CCP1
resets TMR1 and starts an A/D conversion (if A/D module is enabled)
11xx = PWM mode
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 81
PIC16F87/88
9.1
9.1.2
Capture Mode
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register when an event occurs
on CCP1 pin. An event is defined as:
•
•
•
•
Every falling edge
Every rising edge
Every 4th rising edge
Every 16th rising edge
9.1.1
CCP PIN CONFIGURATION
In Capture mode, the CCP1 pin should be configured
as an input by setting the TRISB<x> bit.
Note 1: If the CCP1 pin is configured as an
output, a write to the port can cause a
capture condition.
2: The TRISB bit (0 or 3) is dependent upon
the setting of configuration bit 12
(CCPMX).
FIGURE 9-1:
CAPTURE MODE
OPERATION BLOCK
DIAGRAM
CCPR1H
and
Edge Detect
SOFTWARE INTERRUPT
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep bit
CCP1IE (PIE1<2>) clear to avoid false interrupts and
should clear the flag bit, CCP1IF, following any such
change in operating mode.
9.1.4
CCP PRESCALER
There are four prescaler settings, specified by bits
CCP1M3:CCP1M0. Whenever the CCP module is
turned off, or the CCP module is not in Capture mode,
the prescaler counter is cleared. This means that any
RESET will clear the prescaler counter.
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared, therefore, the first capture may be from
a non-zero prescaler. Example 9-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter
and will not generate the “false” interrupt.
EXAMPLE 9-1:
CLRF
MOVLW
Set Flag bit CCP1IF
(PIR1<2>)
Prescaler
÷ 1, 4, 16
CCP1 Pin
Timer1 must be running in Timer mode or Synchronized Counter mode for the CCP module to use the
capture feature. In Asynchronous Counter mode, the
capture operation may not work.
9.1.3
An event is selected by control bits CCP1M3:CCP1M0
(CCP1CON<3:0>). When a capture is made, the interrupt request flag bit, CCP1IF (PIR1<2>), is set. It must
be cleared in software. If another capture occurs before
the value in register CCPR1 is read, the old captured
value is overwritten by the new captured value.
TIMER1 MODE SELECTION
CCPR1L
MOVWF
CHANGING BETWEEN
CAPTURE PRESCALERS
CCP1CON
;Turn CCP module off
NEW_CAPT_PS ;Load the W reg with
;the new prescaler
;move value and CCP ON
CCP1CON
;Load CCP1CON with this
;value
Capture
Enable
TMR1H
TMR1L
CCP1CON<3:0>
Q’s
DS30487B-page 82
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
9.2
9.2.1
Compare Mode
CCP PIN CONFIGURATION
The user must configure the CCP1 pin as an output by
clearing the TRISB<x> bit.
In Compare mode, the 16-bit CCPR1 register value is
constantly compared against the TMR1 register pair
value. When a match occurs, the CCP1 pin is:
Note 1: Clearing the CCP1CON register will force
the CCP1 compare output latch to the
default low level. This is not the data
latch.
• Driven high
• Driven low
• Remains unchanged
2: The TRISB bit (0 or 3) is dependent upon
the setting of configuration bit 12
(CCPMX).
The action on the pin is based on the value of control
bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the
same time, interrupt flag bit, CCP1IF, is set.
FIGURE 9-2:
9.2.2
COMPARE MODE
OPERATION BLOCK
DIAGRAM
Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the
compare feature. In Asynchronous Counter mode, the
compare operation may not work.
Special Event Trigger
Set Flag bit CCP1IF
(PIR1<2>)
9.2.3
Q
S
R
TRISB<x>
Output Enable
Output
Logic
Match
CCP1CON<3:0>
Mode Select
Comparator
TMR1H
SOFTWARE INTERRUPT MODE
When generate software interrupt is chosen, the CCP1
pin is not affected. Only a CCP interrupt is generated (if
enabled).
CCPR1H CCPR1L
CCP1 pin
TIMER1 MODE SELECTION
9.2.4
TMR1L
SPECIAL EVENT TRIGGER
In this mode, an internal hardware trigger is generated
that may be used to initiate an action.
Special event trigger will:
• RESET Timer1, but not set interrupt flag bit, TMR1IF
(PIR1<0>)
• Set bit GO/DONE (ADCON0<2>) bit, which starts an A/D
conversion
The special event trigger output of CCP1 resets the
TMR1 register pair and starts an A/D conversion (if the
A/D module is enabled). This allows the CCPR1 register to effectively be a 16-bit programmable period
register for Timer1.
Note:
TABLE 9-2:
The special event trigger from the CCP1
module will not set interrupt flag bit
TMR1IF (PIR1<0>).
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE AND TIMER1
Value on
all other
RESETS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
0Bh,8Bh
INTCON
10BH,18Bh
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF TMR2IF
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE TMR2IE TMR1IE -000 0000 -000 0000
Address
0Ch
PIR1
TMR1IF -000 0000 -000 0000
8Ch
PIE1
86h
TRISB
PORTB Data Direction Register
1111 1111 1111 1111
0Eh
TMR1L
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
xxxx xxxx uuuu uuuu
0Fh
TMR1H
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
xxxx xxxx uuuu uuuu
—
T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON -000 0000 -uuu uuuu
10h
T1CON
15h
CCPR1L
Capture/Compare/PWM Register 1 (LSB)
xxxx xxxx uuuu uuuu
16h
CCPR1H
Capture/Compare/PWM Register 1 (MSB)
xxxx xxxx uuuu uuuu
17h
CCP1CON
—
—
CCP1X
CCP1Y
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Legend: x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by Capture and Timer1.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 83
PIC16F87/88
9.3
9.3.1
PWM Mode
In Pulse Width Modulation (PWM) mode, the CCP1 pin
produces up to a 10-bit resolution PWM output. Since
the CCP1 pin is multiplexed with the PORTB data latch,
the TRISB<x> bit must be cleared to make the CCP1
pin an output.
Note:
Clearing the CCP1CON register will force
the CCP1 PWM output latch to the default
low level. This is not the PORTB I/O data
latch.
Figure 9-3 shows a simplified block diagram of the
CCP module in PWM mode.
For a step-by-step procedure on how to setup the CCP
module for PWM operation, see Section 9.3.3 “Setup
for PWM Operation”.
FIGURE 9-3:
SIMPLIFIED PWM BLOCK
DIAGRAM
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
following formula.
EQUATION 9-1:
PWM period = [(PR2) + 1] • 4 • TOSC •
(TMR2 prescale value)
PWM frequency is defined as 1/[PWM period].
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
• TMR2 is cleared
• The CCP1 pin is set (exception: if PWM duty
cycle = 0%, the CCP1 pin will not be set)
• The PWM duty cycle is latched from CCPR1L into
CCPR1H
Note:
CCP1CON<5:4>
Duty Cycle Registers
PWM PERIOD
CCPR1L
The Timer2 postscaler (see Section 8.0
“Timer2 Module”) is not used in the determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
CCPR1H (Slave)
CCP1 pin
R
Comparator
TMR2
Q
S
TRISB<x>
Clear Timer,
CCP1 pin and
latch D.C.
PR2
PWM DUTY CYCLE
The PWM duty cycle is specified by writing to the
CCPR1L register and to the CCP1CON<5:4> bits. Up
to 10-bit resolution is available. The CCPR1L contains
the eight MSbs and the CCP1CON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPR1L:CCP1CON<5:4>. The following equation is
used to calculate the PWM duty cycle in time.
(Note 1)
Comparator
9.3.2
EQUATION 9-2:
Note 1:
8-bit timer is concatenated with 2-bit internal Q
clock or 2 bits of the prescaler to create 10-bit
time base.
PWM duty cycle = (CCPR1L:CCP1CON<5:4>) •
TOSC • (TMR2 prescale value)
A PWM output (Figure 9-4) has a time base (period)
and a time that the output stays high (duty cycle). The
frequency of the PWM is the inverse of the period
(1/period).
FIGURE 9-4:
PWM OUTPUT
Period
CCPR1L and CCP1CON<5:4> can be written to at any
time, but the duty cycle value is not latched into
CCPR1H until after a match between PR2 and TMR2
occurs (i.e., the period is complete). In PWM mode,
CCPR1H is a read only register.
The CCPR1H register and a 2-bit internal latch
are used to double-buffer the PWM duty cycle. This
double-buffering is essential for glitchless PWM
operation.
When the CCPR1H and 2-bit latch match TMR2,
concatenated with an internal 2-bit Q clock or 2 bits of
the TMR2 prescaler, the CCP1 pin is cleared.
Duty Cycle
TMR2 = PR2
TMR2 = Duty Cycle
TMR2 = PR2
DS30487B-page 84
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
9.3.3
The maximum PWM resolution (bits) for a given PWM
frequency is given by the following formula.
The following steps should be taken when configuring
the CCP module for PWM operation:
EQUATION 9-3:
Resolution
FOSC
log FPWM
(
=
log(2)
1.
)
Set the PWM period by writing to the PR2
register.
Set the PWM duty cycle by writing to the
CCPR1L register and CCP1CON<5:4> bits.
Make the CCP1 pin an output by clearing the
TRISB<x> bit.
Set the TMR2 prescale value and enable Timer2
by writing to T2CON.
Configure the CCP1 module for PWM operation.
2.
bits
3.
Note:
SETUP FOR PWM OPERATION
If the PWM duty cycle value is longer than
the PWM period, the CCP1 pin will not be
cleared.
4.
5.
Note:
TABLE 9-3:
The TRISB bit (0 or 3) is dependant upon
the setting of configuration bit 12
(CCPMX).
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz
PWM Frequency
1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz
Timer Prescaler (1, 4, 16)
PR2 Value
Maximum Resolution (bits)
TABLE 9-4:
16
4
1
1
1
1
0xFF
0xFF
0xFF
0x3F
0x1F
0x17
10
10
10
8
7
6.6
REGISTERS ASSOCIATED WITH PWM AND TIMER2
Value on
all other
RESETS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
0Bh,8Bh
INTCON
10Bh,18Bh
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
Address
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
-000 0000 -000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE
TMR1IE
-000 0000 -000 0000
86h
TRISB
PORTB Data Direction Register
1111 1111 1111 1111
11h
TMR2
Timer2 Module Register
0000 0000 0000 0000
92h
PR2
Timer2 Module Period Register
1111 1111 1111 1111
12h
T2CON
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
15h
CCPR1L
Capture/Compare/PWM Register 1 (LSB)
xxxx xxxx uuuu uuuu
16h
CCPR1H
Capture/Compare/PWM Register 1 (MSB)
xxxx xxxx uuuu uuuu
17h
CCP1CON
Legend:
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by PWM and Timer2.
—
 2003 Microchip Technology Inc.
—
CCP1X
CCP1Y
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Preliminary
DS30487B-page 85
PIC16F87/88
NOTES:
DS30487B-page 86
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
10.0
10.1
SYNCHRONOUS SERIAL PORT
(SSP) MODULE
SSP Module Overview
The Synchronous Serial Port (SSP) module is a serial
interface useful for communicating with other peripheral or microcontroller devices. These peripheral
devices may be Serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can
operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C)
SPI Mode
This section contains register definitions
operational characteristics of the SPI module.
and
SPI mode allows 8 bits of data to be synchronously
transmitted and received simultaneously. To
accomplish communication, typically three pins are
used:
• Serial Data Out (SDO)
• Serial Data In (SDI)
• Serial Clock (SCK)
RB2/SDO/RX/DT
RB1/SDI/SDA
RB4/SCK/SCL
Additionally, a fourth pin may be used when in a Slave
mode of operation:
An overview of I2C operations and additional information on the SSP module can be found in the PICmicro®
Mid-Range
MCU
Family
Reference Manual
(DS33023).
Refer to Application Note AN578, “Use of the SSP
Module in the I 2C™ Multi-Master Environment”
(DS00578).
 2003 Microchip Technology Inc.
10.2
• Slave Select (SS)
RB5/SS/TX/CK
When initializing the SPI, several options need to be
specified. This is done by programming the appropriate
control bits in the SSPCON register (SSPCON<5:0>)
and the SSPSTAT register (SSPSTAT<7:6>). These
control bits allow the following to be specified:
•
•
•
•
Master mode (SCK is the clock output)
Slave mode (SCK is the clock input)
Clock Polarity (IDLE state of SCK)
Clock Edge (output data on rising/falling
edge of SCK)
• Clock Rate (Master mode only)
• Slave Select mode (Slave mode only)
Preliminary
DS30487B-page 87
PIC16F87/88
REGISTER 10-1:
SSPSTAT: SYNCHRONOUS SERIAL PORT STATUS REGISTER (ADDRESS 94h)
R/W-0
SMP
R/W-0
CKE
R-0
R-0
R-0
R-0
R-0
R-0
D/A
(1)
(1)
R/W
UA
BF
P
S
bit 7
bit 7
bit 0
SMP: SPI Data Input Sample Phase bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time (Microwire®)
SPI Slave mode:
This bit must be cleared when SPI is used in Slave mode.
I2C mode:
This bit must be maintained clear.
bit 6
CKE: SPI Clock Edge Select bit
SPI mode, CKP = 0:
1 = Data transmitted on rising edge of SCK (Microwire alternate)
0 = Data transmitted on falling edge of SCK
SPI mode, CKP = 1:
1 = Data transmitted on falling edge of SCK (Microwire alternate)
0 = Data transmitted on rising edge of SCK
I2C mode:
This bit must be maintained clear.
bit 5
D/A: Data/Address bit (I2C mode only)
In I2 C Slave mode:
1 = Indicates that the last byte received was data
0 = Indicates that the last byte received was address
bit 4
P: STOP bit(1) (I2C mode only)
1 = Indicates that a STOP bit has been detected last
0 = STOP bit was not detected last
bit 3
S: START bit(1) (I2C mode only)
1 = Indicates that a START bit has been detected last (this bit is ‘0’ on RESET)
0 = START bit was not detected last
bit 2
R/W: Read/Write Information bit (I2C mode only)
Holds the R/W bit information following the last address match, and is only valid from address
match to the next START bit, STOP bit, or ACK bit.
1 = Read
0 = Write
bit 1
UA: Update Address bit (10-bit I2C mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
bit 0
BF: Buffer Full Status bit
Receive (SPI and I2 C modes):
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Transmit (in I2 C mode only):
1 = Transmit in progress, SSPBUF is full (8 bits)
0 = Transmit complete, SSPBUF is empty
Note 1: This bit is cleared when the SSP module is disabled (i.e., the SSPEN bit is cleared).
Legend:
R = Readable bit
- n = Value at POR
DS30487B-page 88
W = Writable bit
‘1’ = Bit is set
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
REGISTER 10-2:
SSPCON: SYNCHRONOUS SERIAL PORT CONTROL REGISTER (ADDRESS 14h)
R/W-0
WCOL
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SSPOV
SSPEN(1)
CKP
SSPM3
SSPM2
SSPM1
SSPM0
bit 7
bit 0
bit 7
WCOL: Write Collision Detect bit
1 = An attempt to write the SSPBUF register failed because the SSP module is busy
(must be cleared in software)
0 = No collision
bit 6
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In Master
mode, the overflow bit is not set since each new reception (and transmission) is initiated by
writing to the SSPBUF register.
0 = No overflow
In I2 C mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a
“don’t care” in Transmit mode. SSPOV must be cleared in software in either mode.
0 = No overflow
bit 5
SSPEN: Synchronous Serial Port Enable bit(1)
In SPI mode:
1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In I2 C mode:
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
Note 1: In both modes, when enabled, these pins must be properly configured as input or
output.
bit 4
CKP: Clock Polarity Select bit
In SPI mode:
1 = Transmit happens on falling edge, receive on rising edge. IDLE state for clock is a high level.
0 = Transmit happens on rising edge, receive on falling edge. IDLE state for clock is a low level.
In I2 C Slave mode:
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
bit 3-0
SSPM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = OSC/4
0001 = SPI Master mode, clock = OSC/16
0010 = SPI Master mode, clock = OSC/64
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
0110 = I2C Slave mode, 7-bit address
0111 = I2C Slave mode, 10-bit address
1011 = I2C firmware controlled Master mode (Slave IDLE)
1110 = I2C Slave mode, 7-bit address with START and STOP bit interrupts enabled
1111 = I2C Slave mode, 10-bit address with START and STOP bit interrupts enabled
1000, 1001, 1010, 1100, 1101 = Reserved
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 89
PIC16F87/88
FIGURE 10-1:
SSP BLOCK DIAGRAM
(SPI MODE)
To enable the serial port, SSP enable bit, SSPEN
(SSPCON<5>), must be set. To reset or reconfigure
SPI mode, clear bit SSPEN, re-initialize the SSPCON
register, and then set bit SSPEN. This configures the
SDI, SDO, SCK, and SS pins as serial port pins. For the
pins to behave as the serial port function, they must
have their data direction bits (in the TRISB register)
appropriately programmed. That is:
Internal
Data Bus
Read
Write
SSPBUF reg
• SDI must have TRISB<1> set
• SDO must have TRISB<2> cleared
• SCK (Master mode) must have TRISB<4>
cleared
• SCK (Slave mode) must have TRISB<4> set
• SS must have TRISB<5> set
RB1/SDI/SDA
SSPSR reg
RB5/SS/
TX/CK
Shift
Clock
bit0
RB2/SDO/RX/DT
Note 1: When the SPI is in Slave mode with SS pin
control enabled (SSPCON<3:0> = 0100),
the SPI module will reset if the SS pin is
set to VDD.
SS Control
Enable
2: If the SPI is used in Slave mode with
CKE = 1, then the SS pin control must be
enabled.
Edge
Select
2
Clock Select
SSPM3:SSPM0
4
Edge
Select
RB4/SCK/
SCL
3: When the SPI is in Slave mode with SS pin
control enabled (SSPCON<3:0> = 0100),
the state of SS pin can affect the state
read back from the TRISB<5> bit. The
peripheral OE signal from the SSP module
into PORTB controls the state that is read
back from the TRISB<5> bit. If readmodify-write instructions, such as BSF, are
performed on the TRISB register while the
SS pin is high, this will cause the
TRISB<5> bit to be set, thus disabling the
SDO output.
TMR2 Output
2
Prescaler TCY
4, 16, 64
TRISB<4>
TABLE 10-1:
REGISTERS ASSOCIATED WITH SPI OPERATION
Value on
all other
RESETS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
0Bh,8Bh
INTCON
10Bh,18Bh
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
Address
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF TMR2IF TMR1IF -000 0000 -000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE TMR2IE TMR1IE -000 0000 -000 0000
86h
TRISB
PORTB Data Direction Register
13h
SSPBUF
Synchronous Serial Port Receive Buffer/Transmit Register
14h
SSPCON
WCOL SSPOV SSPEN
94h
Legend:
SSPSTAT
SMP
CKE
D/A
1111 1111 1111 1111
CKP
P
SSPM3 SSPM2
S
R/W
xxxx xxxx uuuu uuuu
SSPM1
UA
SSPM0 0000 0000 0000 0000
BF
0000 0000 0000 0000
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the SSP in SPI mode.
DS30487B-page 90
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 10-2:
SPI MODE TIMING, MASTER MODE
SCK (CKP = 0,
CKE = 0)
SCK (CKP = 0,
CKE = 1)
SCK (CKP = 1,
CKE = 0)
SCK (CKP = 1,
CKE = 1)
bit 7
SDO
bit 6
bit 5
bit 2
bit 3
bit 4
bit 1
bit 0
SDI (SMP = 0)
bit 7
bit 0
SDI (SMP = 1)
bit 7
bit 0
SSPIF
FIGURE 10-3:
SPI MODE TIMING (SLAVE MODE WITH CKE = 0)
SS (Optional)
SCK (CKP = 0)
SCK (CKP = 1)
bit 7
SDO
bit 6
bit 5
bit 2
bit 3
bit 4
bit 1
bit 0
SDI (SMP = 0)
bit 7
bit 0
SSPIF
FIGURE 10-4:
SPI MODE TIMING (SLAVE MODE WITH CKE = 1)
SS
SCK (CKP = 0)
SCK (CKP = 1)
SDO
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SDI (SMP = 0)
bit 7
bit 0
SSPIF
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 91
PIC16F87/88
10.3
SSP I 2C Mode Operation
The SSP module in I 2C mode fully implements all slave
functions, except general call support, and provides
interrupts on START and STOP bits in hardware to
facilitate firmware implementations of the master functions. The SSP module implements the standard mode
specifications, as well as 7-bit and 10-bit addressing.
Two pins are used for data transfer. These are the
RB4/SCK/SCL pin, which is the clock (SCL), and the
RB1/SDI/SDA pin, which is the data (SDA). The user
must configure these pins as inputs or outputs through
the TRISB<4,1> bits.
The SSP module functions are enabled by setting SSP
Enable bit SSPEN (SSPCON<5>).
FIGURE 10-5:
Internal
Data Bus
RB4/SCK/
SCL
Write
Additional information on SSP I2C operation may be
found in the PICmicro® Mid-Range MCU Reference
Manual (DS33023).
SSPBUF Reg
Shift
Clock
10.3.1
MSb
LSb
Match Detect
SSPADD Reg
START and
STOP Bit Detect
SLAVE MODE
In Slave mode, the SCL and SDA pins must be configured as inputs (TRISB<4,1> set). The SSP module will
override the input state with the output data, when
required (slave-transmitter).
SSPSR Reg
RB1/
SDI/
SDA
• I 2C Slave mode (7-bit address)
• I 2C Slave mode (10-bit address)
• I 2C Slave mode (7-bit address), with START and
STOP bit interrupts enabled to support firmware
Master mode
• I 2C Slave mode (10-bit address), with START and
STOP bit interrupts enabled to support Firmware
Master mode
• I 2C firmware controlled master operation with
START and STOP bit interrupts enabled, Slave is
IDLE
Selection of any I 2C mode, with the SSPEN bit set,
forces the SCL and SDA pins to be open drain, provided these pins are programmed to inputs by setting
the appropriate TRISB bits. Pull-up resistors must be
provided externally to the SCL and SDA pins for proper
operation of the I2C module.
SSP BLOCK DIAGRAM
(I2C MODE)
Read
The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow
one of the following I 2C modes to be selected:
Addr Match
Set, RESET
S, P Bits
(SSPSTAT Reg)
When an address is matched, or the data transfer after
an address match is received, the hardware automatically will generate the Acknowledge (ACK) pulse, and
then load the SSPBUF register with the received value
currently in the SSPSR register.
Either or both of the following conditions will cause the
SSP module not to give this ACK pulse:
The SSP module has five registers for I2C operation:
a)
•
•
•
•
b)
SSP Control register (SSPCON)
SSP Status register (SSPSTAT)
Serial Receive/Transmit Buffer register (SSPBUF)
SSP Shift register (SSPSR) - Not directly
accessible
• SSP Address register (SSPADD)
The buffer full bit, BF (SSPSTAT<0>), was set
before the transfer was received.
The overflow bit, SSPOV (SSPCON<6>), was
set before the transfer was received.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set.
Table 10-2 shows what happens when a data transfer
byte is received, given the status of bits BF and
SSPOV. The shaded cells show the condition where
user software did not properly clear the overflow condition. Flag bit, BF, is cleared by reading the SSPBUF
register while bit SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I2C specification, as well as the requirement of the SSP
module, are shown in timing parameter #100 and
parameter #101.
DS30487B-page 92
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
10.3.1.1
Addressing
10.3.1.2
Once the SSP module has been enabled, it waits for a
START condition to occur. Following the START condition, the eight bits are shifted into the SSPSR register.
All incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
a)
b)
c)
d)
The SSPSR register value is loaded into the
SSPBUF register.
The buffer full bit, BF, is set.
An ACK pulse is generated.
SSP interrupt flag bit, SSPIF (PIR1<3>), is set
(interrupt is generated if enabled) - on the falling
edge of the ninth SCL pulse.
In 10-bit Address mode, two address bytes need to be
received by the slave device. The five Most Significant
bits (MSbs) of the first address byte specify if this is a
10-bit address. Bit R/W (SSPSTAT<2>) must specify a
write so the slave device will receive the second
address byte. For a 10-bit address, the first byte would
equal ‘1111 0 A9 A8 0’, where A9 and A8 are the
two MSbs of the address.
The sequence of events for 10-bit address is as
follows, with steps 7- 9 for slave transmitter:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Receive first (high) byte of address (bits SSPIF,
BF, and bit UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of address (bits
SSPIF, BF, and UA are set).
Update the SSPADD register with the first (high)
byte of Address, if match releases SCL line, this
will clear bit UA.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated START condition.
Receive first (high) byte of address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
 2003 Microchip Technology Inc.
Reception
When the R/W bit of the address byte is clear and an
address match occurs, the R/W bit of the SSPSTAT
register is cleared. The received address is loaded into
the SSPBUF register.
When the address byte overflow condition exists, then
a no Acknowledge (ACK) pulse is given. An overflow
condition is indicated if either bit, BF (SSPSTAT<0>), is
set or bit, SSPOV (SSPCON<6>), is set.
An SSP interrupt is generated for each data transfer
byte. Flag bit, SSPIF (PIR1<3>), must be cleared in
software. The SSPSTAT register is used to determine
the status of the byte.
10.3.1.3
Transmission
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPSTAT register is set. The received address is
loaded into the SSPBUF register. The ACK pulse will
be sent on the ninth bit, and pin RB4/SCK/SCL is held
low. The transmit data must be loaded into the
SSPBUF register, which also loads the SSPSR register. Then, pin RB4/SCK/SCL should be enabled by setting bit CKP (SSPCON<4>). The master device must
monitor the SCL pin prior to asserting another clock
pulse. The slave devices may be holding off the master
device by stretching the clock. The eight data bits are
shifted out on the falling edge of the SCL input. This
ensures that the SDA signal is valid during the SCL
high time (Figure 10-7).
An SSP interrupt is generated for each data transfer
byte. Flag bit, SSPIF, must be cleared in software, and
the SSPSTAT register is used to determine the status
of the byte. Flag bit, SSPIF, is set on the falling edge of
the ninth clock pulse.
As a slave transmitter, the ACK pulse from the master
receiver is latched on the rising edge of the ninth SCL
input pulse. If the SDA line was high (not ACK), then
the data transfer is complete. When the ACK is latched
by the slave device, the slave logic is reset (resets
SSPSTAT register) and the slave device then monitors
for another occurrence of the START bit. If the SDA line
was low (ACK), the transmit data must be loaded into
the SSPBUF register, which also loads the SSPSR register. Then, pin RB4/SCK/SCL should be enabled by
setting bit CKP.
Preliminary
DS30487B-page 93
PIC16F87/88
TABLE 10-2:
DATA TRANSFER RECEIVED BYTE ACTIONS
Status bits as Data
Transfer is Received
SSPSR → SSPBUF
Generate ACK Pulse
Set bit SSPIF
(SSP Interrupt Occurs if Enabled)
BF
SSPOV
0
0
Yes
Yes
Yes
1
0
No
No
Yes
1
1
No
No
Yes
0
1
No
No
Yes
Note 1:
Shaded cells show the conditions where the user software did not properly clear the overflow condition.
I 2C WAVEFORMS FOR RECEPTION (7-BIT ADDRESS)
FIGURE 10-6:
Receiving Address R/W = 0
SCL
ACK
Receiving Data
Receiving Data
ACK
ACK
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
9
1
A7 A6 A5 A4 A3 A2 A1
SDA
1
S
2
3
4
5
6
7
8
2
SSPIF (PIR1<3>)
3
4
5
6
7
8
9
1
2
3
5
4
8
7
6
9
Cleared in software
BF (SSPSTAT<0>)
P
Bus master
terminates
transfer
SSPBUF register is read
SSPOV (SSPCON<6>)
Bit SSPOV is set because the SSPBUF register is still full
ACK is not sent
I 2C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
FIGURE 10-7:
Receiving Address
A7
SDA
SCL
S
A6
1
2
Data is
sampled
R/W = 1
A5
A4
A3
A2
A1
3
4
5
6
7
8
9
ACK
Transmitting Data
ACK
D7
1
SCL held low
while CPU
responds to SSPIF
SSPIF (PIR1<3>)
D6
D5
D4
D3
D2
D1
D0
2
3
4
5
6
7
8
9
P
Cleared in software
BF (SSPSTAT<0>)
SSPBUF is written in software
CKP (SSPCON<4>)
From SSP Interrupt
Service Routine
Set bit after writing to SSPBUF
(the SSPBUF must be written to
before the CKP bit can be set)
DS30487B-page 94
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
10.3.2
MASTER MODE OPERATION
10.3.3
Master mode operation is supported in firmware using
interrupt generation on the detection of the START and
STOP conditions. The STOP (P) and START (S) bits
are cleared from a RESET, or when the SSP module is
disabled. The STOP (P) and START (S) bits will toggle
based on the START and STOP conditions. Control of
the I 2C bus may be taken when the P bit is set, or the
bus is IDLE and both the S and P bits are clear.
MULTI-MASTER MODE OPERATION
In Multi-Master mode operation, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free.
The STOP (P) and START (S) bits are cleared from a
RESET, or when the SSP module is disabled. The
STOP (P) and START (S) bits will toggle based on the
START and STOP conditions. Control of the I 2C bus
may be taken when bit P (SSPSTAT<4>) is set, or the
bus is IDLE and both the S and P bits clear. When the
bus is busy, enabling the SSP interrupt will generate
the interrupt when the STOP condition occurs.
In Master mode operation, the SCL and SDA lines are
manipulated in firmware by clearing the corresponding
TRISB<4,1> bit(s). The output level is always low, irrespective of the value(s) in PORTB<4,1>. So, when
transmitting data, a ‘1’ data bit must have the
TRISB<1> bit set (input) and a ‘0’ data bit must have
the TRISB<1> bit cleared (output). The same scenario
is true for the SCL line with the TRISB<4> bit. Pull-up
resistors must be provided externally to the SCL and
SDA pins for proper operation of the I2C module.
In Multi-Master mode operation, the SDA line must be
monitored to see if the signal level is the expected output level. This check only needs to be done when a
high level is output. If a high level is expected and a low
level is present, the device needs to release the SDA
and SCL lines (set TRISB<4,1>). There are two stages
where this arbitration can be lost:
The following events will cause the SSP Interrupt Flag
bit, SSPIF, to be set (SSP Interrupt if enabled):
• Address Transfer
• Data Transfer
• START condition
• STOP condition
• Data transfer byte transmitted/received
When the slave logic is enabled, the slave device continues to receive. If arbitration was lost during the
address transfer stage, communication to the device
may be in progress. If addressed, an ACK pulse will be
generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at
a later time.
Master mode operation can be done with either the
Slave mode IDLE (SSPM3:SSPM0 = 1011) or with the
Slave mode active. When both Master mode operation
and Slave modes are used, the software needs to
differentiate the source(s) of the interrupt.
For more information on Multi-Master mode operation,
see Application Note AN578, “Use of the SSP Module
in the of I2C™ Multi-Master Environment”.
For more information on Master mode operation, see
Application Note AN554, “Software Implementation of
I2C™ Bus Master”.
TABLE 10-3:
REGISTERS ASSOCIATED WITH I2C OPERATION
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Value on
all other
RESETS
0Bh, 8Bh,
INTCON
10Bh,18Bh
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x
0000 000u
Address
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF CCP1IF TMR2IF TMR1IF
-000 0000
-000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE CCP1IE TMR2IE TMR1IE
-000 0000
-000 0000
13h
SSPBUF
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx
uuuu uuuu
93h
SSPADD
Synchronous Serial Port (I2C mode) Address Register
0000 0000
0000 0000
14h
SSPCON
WCOL
SSPOV
0000 0000
0000 0000
94h
SSPSTAT
(1)
(1)
86h
TRISB
Legend:
Note 1:
SMP
CKE
SSPEN
CKP
D/A
P
SSPM3 SSPM2 SSPM1 SSPM0
S
R/W
PORTB Data Direction Register
UA
BF
0000 0000
0000 0000
1111 1111
1111 1111
x = unknown, u = unchanged, - = unimplemented locations read as ‘0’.
Shaded cells are not used by SSP module in SPI mode.
Maintain these bits clear in I2C mode.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 95
PIC16F87/88
NOTES:
DS30487B-page 96
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
11.0
ADDRESSABLE UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (USART)
The USART can be configured in the following modes:
• Asynchronous (full-duplex)
• Synchronous - Master (half-duplex)
• Synchronous - Slave (half-duplex)
The Universal Synchronous Asynchronous Receiver
Transmitter (USART) module is one of the two serial
I/O modules. (USART is also known as a Serial Communications Interface or SCI.) The USART can be configured as a full-duplex asynchronous system that can
communicate with peripheral devices, such as CRT terminals and personal computers, or it can be configured
as a half-duplex synchronous system that can communicate with peripheral devices, such as A/D or D/A
integrated circuits, serial EEPROMs, etc.
REGISTER 11-1:
Bit SPEN (RCSTA<7>) and bits TRISB<5,2> have to
be set in order to configure pins, RB5/SS/TX/CK and
RB2/SDO/RX/DT, as the Universal Synchronous
Asynchronous Receiver Transmitter.
The USART module also has a multi-processor
communication capability, using 9-bit address
detection.
TXSTA: TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h)
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
R-1
R/W-0
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
bit 7
bit 0
bit 7
CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care.
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6
TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5
TXEN: Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
Note:
SREN/CREN overrides TXEN in Sync mode.
bit 4
SYNC: USART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3
Unimplemented: Read as ‘0’
bit 2
BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High-speed
0 = Low-speed
Synchronous mode:
Unused in this mode.
bit 1
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0
TX9D: 9th bit of Transmit Data, can be Parity bit
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 97
PIC16F87/88
REGISTER 11-2:
RCSTA: RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
R-0
R-x
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
bit 7
bit 0
bit 7
SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RB2/SDO/RX/DT and RB5/SS/TX/CK pins as serial port pins)
0 = Serial port disabled
bit 6
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care.
Synchronous mode - Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode - Slave:
Don’t care.
bit 4
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables continuous receive
0 = Disables continuous receive
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and load of the receive buffer when RSR<8>
is set
0 = Disables address detection, all bytes are received, and ninth bit can be used as parity bit
bit 2
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
bit 1
OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0
RX9D: 9th bit of Received Data (can be Parity bit, but must be calculated by user firmware)
Legend:
DS30487B-page 98
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
11.1
11.1.1
USART Baud Rate Generator
(BRG)
The PIC16F87/88 has an 8 MHz INTRC that can be
used as the system clock, thereby eliminating the need
for external components to provide the clock source.
When the INTRC provides the system clock, the
USART module will also use the INTRC as its system
clock. Table 11-1 shows some of the INTRC frequencies that can be used to generate the USART’s
baud rate.
The BRG supports both the Asynchronous and Synchronous modes of the USART. It is a dedicated 8-bit
baud rate generator. The SPBRG register controls the
period of a free-running 8-bit timer. In Asynchronous
mode, bit BRGH (TXSTA<2>) also controls the baud
rate. In Synchronous mode, bit BRGH is ignored.
Table 11-1 shows the formula for computation of the
baud rate for different USART modes, which only apply
in Master mode (internal clock).
11.1.2
LOW-POWER MODE OPERATION
The system clock is used to generate the desired baud
rate; however, when a low-power mode is entered, the
low-power clock source may be operating at a different
frequency than in full power execution. In SLEEP
mode, no clocks are present. This may require the
value in SPBRG to be adjusted.
Given the desired baud rate and FOSC, the nearest
integer value for the SPBRG register can be calculated
using the formula in Table 11-1. From this, the error in
baud rate can be determined.
It may be advantageous to use the high baud rate
(BRGH = 1) even for slower baud clocks. This is
because the FOSC/(16(X + 1)) equation can reduce the
baud rate error in some cases.
11.1.3
SAMPLING
The data on the RB2/SDO/RX/DT pin is sampled three
times by a majority detect circuit to determine if a high
or a low level is present at the RX pin.
Writing a new value to the SPBRG register causes the
BRG timer to be reset (or cleared). This ensures the
BRG does not wait for a timer overflow before
outputting the new baud rate.
TABLE 11-1:
USART AND INTRC OPERATION
BAUD RATE FORMULA
SYNC
BRGH = 0 (Low-speed)
BRGH = 1 (High-speed)
0
1
(Asynchronous) Baud Rate = FOSC/(64(X + 1))
(Synchronous) Baud Rate = FOSC/(4(X + 1))
Baud Rate = FOSC/(16(X + 1))
N/A
Legend: X = value in SPBRG (0 to 255)
TABLE 11-2:
Address
98h
REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR
Name
TXSTA
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
CSRC
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010
0000 -010
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
0000 000x
0000 000x
0000 0000
0000 0000
18h
RCSTA
99h
SPBRG
Legend:
x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used by the BRG.
Baud Rate Generator Register
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 99
PIC16F87/88
TABLE 11-3:
BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 0)
FOSC = 20 MHz
BAUD
RATE
(K)
%
ERROR
KBAUD
FOSC = 16 MHz
SPBRG
value
(decimal)
%
ERROR
KBAUD
FOSC = 10 MHz
SPBRG
value
(decimal)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
—
—
—
—
—
—
—
—
—
1.2
1.221
+1.75
255
1.202
+0.17
207
1.202
+0.17
129
2.4
2.404
+0.17
129
2.404
+0.17
103
2.404
+0.17
64
9.6
9.766
+1.73
31
9.615
+0.16
25
9.766
+1.73
15
19.2
19.531
+ 1.72
15
19.231
+0.16
12
19.531
+1.72
7
28.8
31.250
+8.51
9
27.778
-3.55
8
31.250
+8.51
4
33.6
34.722
+3.34
8
35.714
+6.29
6
31.250
-6.99
4
57.6
62.500
+8.51
4
62.500
+8.51
3
52.083
-9.58
2
HIGH
1.221
—
255
0.977
—
255
0.610
—
255
LOW
312.500
—
0
250.000
—
0
156.250
—
0
FOSC = 4 MHz
BAUD
RATE
(K)
KBAUD
FOSC = 3.6864 MHz
%
ERROR
SPBRG
value
(decimal)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
0.300
0
207
0.3
0
191
1.2
1.202
+0.17
51
1.2
0
47
2.4
2.404
+0.17
25
2.4
0
23
9.6
8.929
+6.99
6
9.6
0
5
19.2
20.833
+8.51
2
19.2
0
2
28.8
31.250
+8.51
1
28.8
0
1
33.6
—
—
—
—
—
—
57.6
62.500
+8.51
0
57.6
0
0
HIGH
0.244
—
255
0.225
—
255
LOW
62.500
—
0
57.6
—
0
TABLE 11-4:
BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 1)
FOSC = 20 MHz
FOSC = 16 MHz
BAUD
RATE
(K)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
—
—
1.2
—
—
2.4
—
FOSC = 10 MHz
KBAUD
%
ERROR
SPBRG
value
(decimal)
KBAUD
%
ERROR
SPBRG
value
(decimal)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2.441
+1.71
255
64
9.6
9.615
+0.16
129
9.615
+0.16
103
9.615
+0.16
19.2
19.231
+0.16
64
19.231
+0.16
51
19.531
+1.72
31
28.8
29.070
+0.94
42
29.412
+2.13
33
28.409
-1.36
21
33.6
33.784
+0.55
36
33.333
-0.79
29
32.895
-2.10
18
57.6
59.524
+3.34
20
58.824
+2.13
16
56.818
-1.36
10
HIGH
4.883
—
255
3.906
—
255
2.441
—
255
LOW
1250.000
—
0
1000.000
—
0
625.000
—
0
FOSC = 4 MHz
BAUD
RATE
(K)
KBAUD
FOSC = 3.6864 MHz
%
ERROR
SPBRG
value
(decimal)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
—
—
—
—
—
—
1.2
1.202
+0.17
207
1.2
0
191
2.4
2.404
+0.17
103
2.4
0
95
9.6
9.615
+0.16
25
9.6
0
23
19.2
19.231
+0.16
12
19.2
0
11
28.8
27.798
-3.55
8
28.8
0
7
33.6
35.714
+6.29
6
32.9
-2.04
6
57.6
62.500
+8.51
3
57.6
0
3
HIGH
0.977
—
255
0.9
—
255
LOW
250.000
—
0
230.4
—
0
DS30487B-page 100
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 11-5:
INTRC BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 0)
FOSC = 8 MHz
BAUD
RATE
(K)
KBAUD
%
ERROR
FOSC = 4 MHz
SPBRG
value
(decimal)
KBAUD
FOSC = 2 MHz
%
ERROR
SPBRG
value
(decimal)
KBAUD
FOSC = 1 MHz
%
ERROR
SPBRG
value
(decimal)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
NA
—
—
0.300
0
207
0.300
0
103
0.300
0
51
1.2
1.202
+0.16
103
1.202
+0.16
51
1.202
+0.16
25
1.202
+0.16
12
2.4
2.404
+0.16
51
2.404
+0.16
25
2.404
+0.16
12
2.232
-6.99
6
9.6
9.615
+0.16
12
8.929
-6.99
6
10.417
+8.51
2
NA
—
—
19.2
17.857
-6.99
6
20.833
+8.51
2
NA
—
—
NA
—
—
28.8
31.250
+8.51
3
31.250
+8.51
1
31.250
+8.51
0
NA
—
—
38.4
41.667
+8.51
2
NA
—
—
NA
—
—
NA
—
—
57.6
62.500
+8.51
1
62.500
8.51
0
NA
—
—
NA
—
—
TABLE 11-6:
INTRC BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 1)
FOSC = 8 MHz
FOSC = 4 MHz
FOSC = 2 MHz
FOSC = 1 MHz
BAUD
RATE
(K)
KBAUD
%
ERROR
SPBRG
value
(decimal)
0.3
NA
—
—
NA
—
—
NA
—
—
1.2
NA
—
—
1.202
+0.16
207
1.202
+0.16
103
2.4
2.404
+0.16
207
2.404
+0.16
103
2.404
+0.16
51
9.6
9.615
+0.16
51
9.615
+0.16
25
9.615
+0.16
19.2
19.231
+0.16
25
19.231
+0.16
12
17.857
28.8
29.412
+2.12
16
27.778
-3.55
8
31.250
38.4
38.462
+0.16
12
35.714
-6.99
6
41.667
+8.51
2
57.6
55.556
-3.55
8
62.500
+8.51
3
62.500
+8.51
1
 2003 Microchip Technology Inc.
KBAUD
%
ERROR
SPBRG
value
(decimal)
KBAUD
Preliminary
SPBRG
value
(decimal)
%
ERROR
SPBRG
value
(decimal)
0.300
0
207
1.202
+0.16
51
2.404
+0.16
25
12
8.929
-6.99
6
-6.99
6
20.833
+8.51
2
+8.51
3
31.250
+8.51
1
NA
—
—
62.500
+8.51
0
%
ERROR
KBAUD
DS30487B-page 101
PIC16F87/88
11.2
USART Asynchronous Mode
rupt can be enabled/disabled by setting/clearing
enable bit, TXIE (PIE1<4>). Flag bit TXIF will be set,
regardless of the state of enable bit TXIE and cannot be
cleared in software. It will reset only when new data is
loaded into the TXREG register. While flag bit TXIF
indicates the status of the TXREG register, another bit,
TRMT (TXSTA<1>), shows the status of the TSR register. Status bit TRMT is a read-only bit, which is set
when the TSR register is empty. No interrupt logic is
tied to this bit, so the user has to poll this bit in order to
determine if the TSR register is empty.
In this mode, the USART uses standard non-return-tozero (NRZ) format (one START bit, eight or nine data
bits, and one STOP bit). The most common data format
is 8 bits. An on-chip, dedicated, 8-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. The USART transmits and
receives the LSb first. The transmitter and receiver are
functionally independent, but use the same data format
and baud rate. The baud rate generator produces a
clock, either x16 or x64 of the bit shift rate, depending
on bit BRGH (TXSTA<2>). Parity is not supported by
the hardware, but can be implemented in software (and
stored as the ninth data bit). Asynchronous mode is
stopped during SLEEP.
Note 1: The TSR register is not mapped in data
memory, so it is not available to the user.
2: Flag bit TXIF is set when enable bit TXEN
is set. TXIF is cleared by loading TXREG.
Asynchronous mode is selected by clearing bit SYNC
(TXSTA<4>).
Transmission is enabled by setting enable bit TXEN
(TXSTA<5>). The actual transmission will not occur
until the TXREG register has been loaded with data
and the baud rate generator (BRG) has produced a
shift clock (Figure 11-2). The transmission can also be
started by first loading the TXREG register and then
setting enable bit TXEN. Normally, when transmission
is first started, the TSR register is empty. At that point,
transfer to the TXREG register will result in an immediate transfer to TSR, resulting in an empty TXREG. A
back-to-back transfer is thus possible (Figure 11-3).
Clearing enable bit TXEN during a transmission will
cause the transmission to be aborted and will reset the
transmitter. As a result, the RB5/SS/TX/CK pin will
revert to high-impedance.
The USART Asynchronous module consists of the
following important elements:
•
•
•
•
Baud Rate Generator
Sampling Circuit
Asynchronous Transmitter
Asynchronous Receiver
11.2.1
USART ASYNCHRONOUS
TRANSMITTER
The USART transmitter block diagram is shown in
Figure 11-1. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the STOP
bit has been transmitted from the previous load. As
soon as the STOP bit is transmitted, the TSR is loaded
with new data from the TXREG register (if available).
Once the TXREG register transfers the data to the TSR
register (occurs in one TCY), the TXREG register is
empty and flag bit, TXIF (PIR1<4>), is set. This inter-
FIGURE 11-1:
In order to select 9-bit transmission, transmit bit, TX9
(TXSTA<6>), should be set and the ninth bit should be
written to TX9D (TXSTA<0>). The ninth bit must be
written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG register can result in an immediate transfer of the data to the
TSR register (if the TSR is empty). In such a case, an
incorrect ninth data bit may be loaded in the TSR
register.
USART TRANSMIT BLOCK DIAGRAM
Data Bus
TXIF
TXREG Register
TXIE
8
MSb
(8)
• • •
LSb
0
Pin Buffer
and Control
TSR Register
RB5/SS/TX/CK pin
Interrupt
TXEN
Baud Rate CLK
TRMT
SPEN
SPBRG
Baud Rate Generator
TX9
TX9D
DS30487B-page 102
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
When setting up an asynchronous transmission, follow
these steps:
4.
1.
5.
Initialize the SPBRG register for the appropriate
baud rate. If a high-speed baud rate is desired,
set bit BRGH (Section 11.1 “USART Baud
Rate Generator (BRG)”).
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, then set enable bit
TXIE.
2.
3.
FIGURE 11-2:
If 9-bit transmission is desired, then set transmit
bit TX9.
Enable the transmission by setting bit TXEN,
which will also set bit TXIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG register (starts
transmission).
If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
6.
7.
8.
ASYNCHRONOUS MASTER TRANSMISSION
Write to TXREG
Word 1
BRG Output
(Shift Clock)
RB5/SS/TX/CK pin
START Bit
Bit 0
Bit 1
Word 1
TXIF bit
(Transmit Buffer
Reg. Empty Flag)
Bit 7/8
STOP Bit
Word 1
Transmit Shift Reg
TRMT bit
(Transmit Shift
Reg. Empty Flag)
FIGURE 11-3:
ASYNCHRONOUS MASTER TRANSMISSION (BACK TO BACK)
Write to TXREG
Word 2
Word 1
BRG Output
(Shift Clock)
RB5/SS/TX/CK pin
START Bit
Bit 0
TXIF bit
(Interrupt Reg. Flag)
TRMT bit
(Transmit Shift
Reg. Empty Flag)
Note:
Bit 7/8
Word 1
Transmit Shift Reg.
STOP Bit START Bit
Word 2
Bit 0
Word 2
Transmit Shift Reg.
This timing diagram shows two consecutive transmissions.
TABLE 11-7:
Address
Bit 1
Word 1
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
-000 000x
-000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
-000 0000
-000 0000
SPEN
RX9
SREN
CREN
—
FERR
OERR
RX9D
0000 -00x
0000 -00x
0000 0000
0000 0000
-000 0000
0Ch
PIR1
18h
RCSTA
19h
TXREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG Baud Rate Generator Register
Legend:
x = unknown, - = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous transmission.
USART Transmit Register
—
ADIE
RCIE
TXIE
CSRC
TX9
TXEN
SYNC
 2003 Microchip Technology Inc.
SSPIE CCP1IE
—
BRGH
Preliminary
TMR2IE
TMR1IE
-000 0000
TRMT
TX9D
0000 -010
0000 -010
0000 0000
0000 0000
DS30487B-page 103
PIC16F87/88
11.2.2
USART ASYNCHRONOUS
RECEIVER
is possible for two bytes of data to be received and
transferred to the RCREG FIFO and a third byte to
begin shifting to the RSR register. On the detection of
the STOP bit of the third byte, if the RCREG register is
still full, the Overrun Error bit, OERR (RCSTA<1>), will
be set. The word in the RSR will be lost. The RCREG
register can be read twice to retrieve the two bytes in
the FIFO. Overrun bit OERR has to be cleared in software. This is done by resetting the receive logic (CREN
is cleared and then set). If bit OERR is set, transfers
from the RSR register to the RCREG register are inhibited, and no further data will be received. It is, therefore,
essential to clear error bit OERR if it is set. Framing
Error bit, FERR (RCSTA<2>), is set if a STOP bit is
detected as clear. Bit FERR and the 9th receive bit are
buffered the same way as the receive data. Reading
the RCREG will load bits RX9D and FERR with new
values, therefore, it is essential for the user to read the
RCSTA register before reading the RCREG register, in
order not to lose the old FERR and RX9D information.
The receiver block diagram is shown in Figure 11-4.
The data is received on the RB2/SDO/RX/DT pin and
drives the data recovery block. The data recovery block
is actually a high-speed shifter, operating at x16 times
the baud rate; whereas, the main receive serial shifter
operates at the bit rate or at FOSC.
Once Asynchronous mode is selected, reception is
enabled by setting bit CREN (RCSTA<4>).
The heart of the receiver is the Receive (Serial) Shift
register (RSR). After sampling the STOP bit, the
received data in the RSR is transferred to the RCREG
register (if it is empty). If the transfer is complete, flag
bit, RCIF (PIR1<5>), is set. The actual interrupt can be
enabled/disabled by setting/clearing enable bit RCIE
(PIE1<5>). Flag bit RCIF is a read only bit, which is
cleared by the hardware. It is cleared when the RCREG
register has been read and is empty. The RCREG is a
double buffered register (i.e., it is a two-deep FIFO). It
FIGURE 11-4:
USART RECEIVE BLOCK DIAGRAM
x64 Baud Rate CLK
SPBRG
Baud Rate Generator
FERR
OERR
CREN
FOSC
÷64
or
÷16
RSR Register
MSb
STOP (8)
• • •
7
1
LSb
0 START
RB2/SDO/RX/DT
Pin Buffer
and Control
RX9
Data
Recovery
RX9D
SPEN
Interrupt
RCREG Register
8
RCIF
Data Bus
RCIE
FIGURE 11-5:
ASYNCHRONOUS RECEPTION
START
bit
bit 0
RX pin
Rcv Shift
Reg
Rcv Buffer Reg
Read Rcv
Buffer Reg
RCREG
FIFO
bit 1
bit 7/8 STOP
bit
START
bit
bit 0
Word 1
RCREG
bit 7/8 STOP
bit
START
bit
bit 7/8 STOP
bit
Word 2
RCREG
RCIF
(Interrupt Flag)
OERR bit
CREN
Note:
This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word,
causing the OERR (overrun) bit to be set.
DS30487B-page 104
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
When setting up an asynchronous reception, follow
these steps:
1.
2.
3.
4.
5.
6.
Flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable
bit RCIE is set.
7. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
8. Read the 8-bit received data by reading the
RCREG register.
9. If any error occurred, clear the error by clearing
enable bit CREN.
10. If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
Initialize the SPBRG register for the appropriate
baud rate. If a high-speed baud rate is desired,
set bit BRGH (Section 11.1 “USART Baud
Rate Generator (BRG)”).
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, then set enable bit
RCIE.
If 9-bit reception is desired, then set bit RX9.
Enable the reception by setting bit CREN.
TABLE 11-8:
Address
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF TMR2IF TMR1IF
SPEN
RX9
SREN
CREN
—
0Ch
PIR1
18h
RCSTA
1Ah
RCREG USART Receive Register
8Ch
PIE1
—
ADIE
RCIE
TXIE
CSRC
TX9
TXEN
SYNC
FERR
OERR
RX9D
SSPIE CCP1IE TMR2IE TMR1IE
-000 0000
-000 0000
0000 -00x
0000 -00x
0000 0000
0000 0000
-000 0000
-000 0000
0000 -010
0000 -010
0000 0000
0000 0000
98h
TXSTA
99h
SPBRG
Legend:
x = unknown, - = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
—
BRGH
Baud Rate Generator Register
 2003 Microchip Technology Inc.
Preliminary
TRMT
TX9D
DS30487B-page 105
PIC16F87/88
11.2.3
SETTING UP 9-BIT MODE WITH
ADDRESS DETECT
• Flag bit RCIF will be set when reception is complete, and an interrupt will be generated if enable
bit RCIE was set.
• Read the RCSTA register to get the ninth bit and
determine if any error occurred during reception.
• Read the 8-bit received data by reading the
RCREG register, to determine if the device is
being addressed.
• If any error occurred, clear the error by clearing
enable bit CREN.
• If the device has been addressed, clear the
ADDEN bit to allow data bytes and address bytes
to be read into the receive buffer, and interrupt the
CPU.
When setting up an asynchronous reception with
address detect enabled:
• Initialize the SPBRG register for the appropriate
baud rate. If a high-speed baud rate is desired,
set bit BRGH.
• Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
• If interrupts are desired, then set enable bit RCIE.
• Set bit RX9 to enable 9-bit reception.
• Set ADDEN to enable address detect.
• Enable the reception by setting enable bit CREN.
FIGURE 11-6:
USART RECEIVE BLOCK DIAGRAM
x64 Baud Rate CLK
FERR
OERR
CREN
FOSC
SPBRG
÷ 64
RSR Register
MSb
or
Baud Rate Generator
÷ 16
STOP (8)
7
• • •
1
LSb
0 START
RB2/SDO/RX/DT
Pin Buffer
and Control
Data
Recovery
RX9
8
SPEN
RX9
ADDEN
Enable
Load of
RX9
ADDEN
RSR<8>
Receive
Buffer
8
RX9D
RCREG Register
FIFO
8
Interrupt
RCIF
Data Bus
RCIE
DS30487B-page 106
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 11-7:
ASYNCHRONOUS RECEPTION WITH ADDRESS DETECT
RB2/SDO/RX/DT pin
START
bit
bit 0
bit 1
bit 8 STOP
bit
START
bit
bit 0
bit 8
STOP
bit
Load RSR
Bit 8 = 0, Data Byte
Bit 8 = 1, Address Byte
Word 1
RCREG
Read
RCIF
Note:
This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer)
because ADDEN = 1.
FIGURE 11-8:
ASYNCHRONOUS RECEPTION WITH ADDRESS BYTE FIRST
RB2/SDO/RX/DT pin
START
bit bit 0
bit 1
bit 8 STOP
bit
START
bit
bit 0
bit 8
STOP
bit
Load RSR
Bit 8 = 1, Address Byte
Bit 8 = 0, Data Byte
Word 1
RCREG
Read
RCIF
Note:
This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer)
because ADDEN was not updated and still = 0.
TABLE 11-9:
Address
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
0Ch
PIR1
18h
RCSTA
1Ah
RCREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
SPEN
RX9
SREN
CREN ADDEN
FERR
TMR2IF TMR1IF -000 0000
OERR
RX9D
0000 000x
0000 0000
0000 0000
CCP1IE TMR2IE TMR1IE -000 0000
-000 0000
USART Receive Register
—
ADIE
RCIE
TXIE
SSPIE
CSRC
TX9
TXEN
SYNC
—
-000 0000
0000 000x
BRGH
Baud Rate Generator Register
TRMT
TX9D
0000 -010
0000 -010
0000 0000
0000 0000
x = unknown, - = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 107
PIC16F87/88
11.3
USART Synchronous
Master Mode
In Synchronous Master mode, the data is transmitted in
a half-duplex manner (i.e., transmission and reception
do not occur at the same time). When transmitting data,
the reception is inhibited and vice versa. Synchronous
mode is entered by setting bit SYNC (TXSTA<4>). In
addition, enable bit SPEN (RCSTA<7>) is set in order
to configure the RB5/SS/TX/CK and RB2/SDO/RX/DT
I/O pins to CK (clock) and DT (data) lines, respectively.
The Master mode indicates that the processor transmits the master clock on the CK line. The Master mode
is entered by setting bit CSRC (TXSTA<7>).
11.3.1
USART SYNCHRONOUS MASTER
TRANSMISSION
The USART transmitter block diagram is shown in
Figure 11-6. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG (if available). Once the
TXREG register transfers the data to the TSR register
(occurs in one TCYCLE), the TXREG is empty and interrupt bit TXIF (PIR1<4>) is set. The interrupt can be
enabled/disabled by setting/clearing enable bit TXIE
(PIE1<4>). Flag bit TXIF will be set, regardless of the
state of enable bit TXIE and cannot be cleared in software. It will reset only when new data is loaded into the
TXREG register. While flag bit TXIF indicates the status
of the TXREG register, another bit, TRMT (TXSTA<1>),
shows the status of the TSR register. TRMT is a read
only bit which is set when the TSR is empty. No interrupt logic is tied to this bit, so the user has to poll this
bit in order to determine if the TSR register is empty.
The TSR is not mapped in data memory, so it is not
available to the user.
Transmission is enabled by setting enable bit TXEN
(TXSTA<5>). The actual transmission will not occur
until the TXREG register has been loaded with data.
The first data bit will be shifted out on the next available
rising edge of the clock on the CK line. Data out is stable around the falling edge of the synchronous clock
(Figure 11-9). The transmission can also be started by
first loading the TXREG register and then setting bit
TXEN (Figure 11-10). This is advantageous when slow
baud rates are selected, since the BRG is kept in
RESET when bits TXEN, CREN and SREN are clear.
Setting enable bit TXEN will start the BRG, creating a
shift clock immediately. Normally, when transmission is
first started, the TSR register is empty, so a transfer to
the TXREG register will result in an immediate transfer
to TSR, resulting in an empty TXREG. Back-to-back
transfers are possible.
DS30487B-page 108
Clearing enable bit TXEN during a transmission will
cause the transmission to be aborted and will reset the
transmitter. The DT and CK pins will revert to highimpedance. If either bit CREN or bit SREN is set during
a transmission, the transmission is aborted and the DT
pin reverts to a hi-impedance state (for a reception).
The CK pin will remain an output if bit CSRC is set
(internal clock). The transmitter logic, however, is not
reset, although it is disconnected from the pins. In order
to reset the transmitter, the user has to clear bit TXEN.
If bit SREN is set (to interrupt an on-going transmission
and receive a single word), then after the single word is
received, bit SREN will be cleared and the serial port
will revert back to transmitting, since bit TXEN is still
set. The DT line will immediately switch from Highimpedance Receive mode to transmit and start driving.
To avoid this, bit TXEN should be cleared.
In order to select 9-bit transmission, the TX9
(TXSTA<6>) bit should be set and the ninth bit should
be written to bit TX9D (TXSTA<0>). The ninth bit must
be written before writing the 8-bit data to the TXREG
register. This is because a data write to the TXREG can
result in an immediate transfer of the data to the TSR
register (if the TSR is empty). If the TSR was empty and
the TXREG was written before writing the “new” TX9D,
the “present” value of bit TX9D is loaded.
Steps to follow when setting up a synchronous master
transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Preliminary
Initialize the SPBRG register for the appropriate
baud rate (Section 11.1 “USART Baud Rate
Generator (BRG)”).
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set bit TX9.
Enable the transmission by setting bit TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the TXREG
register.
If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 11-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Address
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
0Ch
PIR1
18h
RCSTA
19h
TXREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
-000 0000
-000 0000
SPEN
RX9
SREN
CREN
—
FERR
OERR
RX9D
0000 -00x
0000 -00x
USART Transmit Register
—
ADIE
RCIE
TXIE
SSPIE
CSRC
TX9
TXEN
SYNC
—
0000 0000
0000 0000
CCP1IE TMR2IE TMR1IE -000 0000
-000 0000
BRGH
TRMT
TX9D
Baud Rate Generator Register
0000 -010
0000 -010
0000 0000
0000 0000
x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission.
FIGURE 11-9:
SYNCHRONOUS TRANSMISSION
Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2Q3 Q4Q1Q2 Q3 Q4Q1 Q2 Q3 Q4
RB2/SDO/
RX/DT pin
bit 0
bit 1
Q3 Q4 Q1 Q2 Q3Q4 Q1Q2 Q3 Q4 Q1 Q2Q3 Q4Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 2
bit 7
Write to
TXREG Reg
Write Word 1
bit 0
bit 1
bit 7
Word 2
Word 1
RB5/SS/TX/
CK pin
Write Word 2
TXIF bit
(Interrupt Flag)
TRMT bit
TXEN bit
‘1’
‘1’
Note: Sync Master mode; SPBRG = 0. Continuous transmission of two 8-bit words.
FIGURE 11-10:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
RB2/SDO/RX/DT pin
bit 0
bit 1
bit 2
bit 6
bit 7
RB5/SS/TX/CK pin
Write to
TXREG Reg
TXIF bit
TRMT bit
TXEN bit
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 109
PIC16F87/88
11.3.2
USART SYNCHRONOUS MASTER
RECEPTION
receive data. Reading the RCREG register will load bit
RX9D with a new value, therefore, it is essential for the
user to read the RCSTA register before reading RCREG,
in order not to lose the old RX9D information.
Once Synchronous mode is selected, reception is
enabled by setting either enable bit SREN
(RCSTA<5>), or enable bit CREN (RCSTA<4>). Data is
sampled on the RB2/SDO/RX/DT pin on the falling
edge of the clock. If enable bit SREN is set, then only a
single word is received. If enable bit CREN is set, the
reception is continuous until CREN is cleared. If both
bits are set, CREN takes precedence.
When setting up a synchronous master reception:
1.
Initialize the SPBRG register for the appropriate
baud rate (Section 11.1 “USART Baud Rate
Generator (BRG)”).
2. Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
3. Ensure bits CREN and SREN are clear.
4. If interrupts are desired, then set enable bit
RCIE.
5. If 9-bit reception is desired, then set bit RX9.
6. If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
7. Interrupt flag bit, RCIF, will be set when
reception is complete and an interrupt will be
generated if enable bit, RCIE, was set.
8. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
11. If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
After clocking the last bit, the received data in the
Receive Shift Register (RSR) is transferred to the
RCREG register (if it is empty). When the transfer is
complete, interrupt flag bit, RCIF (PIR1<5>), is set. The
actual interrupt can be enabled/disabled by setting/
clearing enable bit RCIE (PIE1<5>).
Flag bit RCIF is a read-only bit, which is reset by the
hardware. In this case, it is reset when the RCREG
register has been read and is empty. The RCREG is a
double-buffered register (i.e., it is a two-deep FIFO). It is
possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting into the RSR register. On the clocking of the last bit
of the third byte, if the RCREG register is still full, then
Overrun Error bit, OERR (RCSTA<1>), is set. The word
in the RSR will be lost. The RCREG register can be read
twice to retrieve the two bytes in the FIFO. Bit OERR has
to be cleared in software (by clearing bit CREN). If bit
OERR is set, transfers from the RSR to the RCREG are
inhibited, so it is essential to clear bit OERR if it is set.
The ninth receive bit is buffered the same way as the
TABLE 11-11: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Address
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
0Ch
PIR1
18h
RCSTA
1Ah
RCREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
TMR1IF
-000 0000
-000 0000
SPEN
RX9
SREN
CREN
—
FERR
OERR
RX9D
0000 -00x
0000 -00x
0000 0000
0000 0000
CCP1IE TMR2IE TMR1IE -000 0000
-000 0000
USART Receive Register
—
ADIE
RCIE
TXIE
SSPIE
CSRC
TX9
TXEN
SYNC
—
BRGH
Baud Rate Generator Register
TRMT
TX9D
0000 -010
0000 -010
0000 0000
0000 0000
x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
DS30487B-page 110
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 11-11:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RB2/SDO/RX/DT
pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
RB5/SS/TX/CK
pin
Write to
bit SREN
SREN bit
CREN bit
‘0’
‘0’
RCIF bit
(Interrupt)
Read
RXREG
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRG = 0.
11.4
USART Synchronous Slave Mode
e)
Synchronous Slave mode differs from the Master mode
in the fact that the shift clock is supplied externally at
the RB5/SS/TX/CK pin (instead of being supplied internally in Master mode). This allows the device to transfer or receive data while in SLEEP mode. Slave mode
is entered by clearing bit CSRC (TXSTA<7>).
11.4.1
When setting up a synchronous slave transmission,
follow these steps:
1.
USART SYNCHRONOUS SLAVE
TRANSMIT
4.
5.
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
b)
c)
d)
Enable the synchronous slave serial port by setting bits SYNC and SPEN and clearing bit
CSRC.
Clear bits CREN and SREN.
If interrupts are desired, then set enable bit
TXIE.
If 9-bit transmission is desired, then set bit TX9.
Enable the transmission by setting enable bit
TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the TXREG
register.
If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
2.
3.
The operation of the Synchronous Master and Slave
modes is identical, except in the case of the SLEEP mode.
a)
If enable bit TXIE is set, the interrupt will wake
the chip from SLEEP and if the global interrupt
is enabled, the program will branch to the
interrupt vector (0004h).
The first word will immediately transfer to the
TSR register and transmit.
The second word will remain in the TXREG register.
Flag bit TXIF will not be set.
When the first word has been shifted out of TSR,
the TXREG register will transfer the second word
to the TSR and flag bit TXIF will now be set.
6.
7.
8.
TABLE 11-12: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Address
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
0Ch
PIR1
18h
RCSTA
19h
TXREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF TMR2IF TMR1IF -000 0000 -000 0000
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
RX9D
USART Transmit Register
0000 000x 0000 000x
0000 0000 0000 0000
—
ADIE
RCIE
TXIE
SSPIE
CSRC
TX9
TXEN
SYNC
—
CCP1IE TMR2IE TMR1IE -000 0000 -000 0000
BRGH
Baud Rate Generator Register
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 111
PIC16F87/88
11.4.2
USART SYNCHRONOUS SLAVE
RECEPTION
When setting up a synchronous slave reception, follow
these steps:
The operation of the Synchronous Master and Slave
modes is identical, except in the case of the SLEEP
mode. Bit SREN is a “don't care” in Slave mode.
1.
If receive is enabled by setting bit CREN prior to the
SLEEP instruction, then a word may be received during
SLEEP. On completely receiving the word, the RSR
register will transfer the data to the RCREG register
and if enable bit RCIE bit is set, the interrupt generated
will wake the chip from SLEEP. If the global interrupt is
enabled, the program will branch to the interrupt vector
(0004h).
2.
3.
4.
5.
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit RCIF will be set when reception is complete and an interrupt will be generated, if
enable bit RCIE was set.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
If using interrupts, ensure that GIE and PEIE
(bits 7 and 6) of the INTCON register are set.
6.
7.
8.
9.
TABLE 11-13: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Address
Name
0Bh, 8Bh, INTCON
10Bh,18Bh
0Ch
PIR1
18h
RCSTA
1Ah
RCREG
8Ch
PIE1
98h
TXSTA
99h
SPBRG
Legend:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on:
POR, BOR
Value on
all other
RESETS
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
R0IF
0000 000x
0000 000u
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF
SPEN
RX9
SREN
CREN
ADDEN
FERR
OERR
TMR1IF -000 0000 -000 0000
RX9D
USART Receive Register
0000 000x 0000 000x
0000 0000 0000 0000
—
ADIE
RCIE
TXIE
SSPIE
CSRC
TX9
TXEN
SYNC
—
CCP1IE TMR2IE TMR1IE -000 0000 -000 0000
BRGH
Baud Rate Generator Register
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
x = unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
DS30487B-page 112
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
12.0
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
The A/D module has five registers:
The Analog-to-Digital (A/D) converter module has
seven inputs for 18/20 pin devices (PIC16F88 devices
only).
The conversion of an analog input signal results in a
corresponding 10-bit digital number. The A/D module
has a high and low voltage reference input that is software selectable to some combination of VDD, VSS,
VREF- (RA2), or VREF+ (RA3).
The A/D converter has a unique feature of being able
to operate while the device is in SLEEP mode. To operate in SLEEP, the A/D conversion clock must be
derived from the A/D’s internal RC oscillator.
REGISTER 12-1:
•
•
•
•
•
A/D Result High Register (ADRESH)
A/D Result Low Register (ADRESL)
A/D Control Register 0 (ADCON0)
A/D Control Register 1 (ADCON1)
Analog Select Register (ANSEL)
The ADCON0 register, shown in Register 12-2, controls the operation of the A/D module. The ANSEL register, shown in Register 12-1 and the ADCON1 register,
shown in Register 12-3, configure the functions of the
port pins. The port pins can be configured as analog
inputs (RA3/RA2 can also be voltage references) or as
digital I/O.
Additional information on using the A/D module can be
found in the PICmicro® Mid-Range MCU Family
Reference Manual (DS33023).
ANSEL REGISTER (ADDRESS 9Bh) PIC16F88 DEVICES ONLY
U-0
—
bit 7
R/W-1
ANS6
R/W-1
ANS5
R/W-1
ANS4
R/W-1
ANS3
R/W-1
ANS2
R/W-1
ANS1
R/W-1
ANS0
bit 0
bit 7
Unimplemented: Read as ‘0’
bit 6-0
ANS<6:0>: Analog Input Select bits
Bits select input function on corresponding AN<6:0> pins.
1 = Analog I/O (see notes below)
0 = Digital I/O
Note 1: Setting a pin to an analog input disables the digital input buffer. The corresponding
TRIS bit should be set to input mode when using pins as analog inputs. Only AN2 is
an analog I/O, all other ANx pins are analog inputs.
2: See the block diagrams for the analog I/O pins to see how ANSEL interacts with the
CHS bits of the ADCON0 register.
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 113
PIC16F87/88
REGISTER 12-2:
ADCON0 REGISTER (ADDRESS 1Fh) PIC16F88 DEVICES ONLY
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
R/W-0
ADCS1
ADCS0
CHS2
CHS1
CHS0
GO/DONE
—
ADON
bit 7
bit 0
bit 7-6
ADCS<1:0>: A/D Conversion Clock Select bits
If ADSC2 = 0:
00 = FOSC/2
01 = FOSC/8
10 = FOSC/32
11 = FRC (clock derived from the internal A/D module RC oscillator)
If ADSC2 = 1:
00 = FOSC/4
01 = FOSC/16
10 = FOSC/64
11 = FRC (clock derived from the internal A/D module RC oscillator)
bit 5-3
CHS<2:0>: Analog Channel Select bits
000 = Channel 0 (RA0/AN0)
001 = Channel 1 (RA1/AN1)
010 = Channel 2 (RA2/AN2)
011 = Channel 3 (RA3/AN3)
100 = Channel 4 (RA4/AN4)
101 = Channel 5 (RB6/AN5)
110 = Channel 6 (RB7/AN6)
bit 2
GO/DONE: A/D Conversion Status bit
If ADON = 1:
1 = A/D conversion in progress (setting this bit starts the A/D conversion)
0 = A/D conversion not in progress (this bit is automatically cleared by hardware when the A/D
conversion is complete)
bit 1
Unimplemented: Read as ‘0’
bit 0
ADON: A/D On bit
1 = A/D converter module is operating
0 = A/D converter module is shut-off and consumes no operating current
Legend:
DS30487B-page 114
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
REGISTER 12-3:
ADCON1 REGISTER (ADDRESS 9Fh) PIC16F88 DEVICES ONLY
R/W-0
ADFM
bit 7
R/W-0
ADCS2
R/W-0
VCFG1
R/W-0
VCFG0
U-0
—
U-0
—
bit 7
ADFM: A/D Result Format Select bit
1 = Right justified. Six Most Significant bits of ADRESH are read as ‘0’.
0 = Left justified. Six Least Significant bits of ADRESL are read as ‘0’.
bit 6
ADCS2: A/D Clock Divide by 2 Select bit
1 = A/D clock source is divided by 2 when system clock is used
0 = Disabled
bit 5-4
VCFG<1:0>: A/D Voltage Reference Configuration bits
Logic State
VREF+
VREF-
00
AVDD
AVSS
01
AVDD
VREF-
10
VREF+
VREF+
VREF-
11
Note:
bit 3-0
U-0
—
U-0
—
bit 0
AVSS
The ANSEL bits for AN3 and AN2 inputs must be configured as analog inputs for the
VREF+ and VREF- external pins to be used.
Unimplemented: Read as ‘0’
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 115
PIC16F87/88
The ADRESH:ADRESL registers contain the result of
the A/D conversion. When the A/D conversion is complete, the result is loaded into the A/D result register
pair, the GO/DONE bit (ADCON0<2>) is cleared, and
A/D Interrupt Flag bit, ADIF, is set. The block diagram
of the A/D module is shown in Figure 12-1.
After the A/D module has been configured as desired,
the selected channel must be acquired before the conversion is started. The analog input channels must
have their corresponding TRIS bits selected as inputs.
2.
3.
4.
5.
To determine sample time, see Section 12.1. After this
sample time has elapsed, the A/D conversion can be
started.
These steps should be followed for doing an A/D
conversion:
6.
1.
7.
Configure the A/D module:
• Configure analog/digital I/O (ANSEL)
• Configure voltage reference (ADCON1)
• Select A/D input channel (ADCON0)
• Select A/D conversion clock (ADCON0)
• Turn on A/D module (ADCON0)
FIGURE 12-1:
Configure A/D interrupt (if desired):
• Clear ADIF bit
• Set ADIE bit
• SET PEIE bit
• Set GIE bit
Wait the required acquisition time.
Start conversion:
• Set GO/DONE bit (ADCON0)
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
(with interrupts disabled); OR
• Waiting for the A/D interrupt
Read A/D Result register pair
(ADRESH:ADRESL), clear bit ADIF if required.
For next conversion, go to step 1 or step 2 as
required. The A/D conversion time per bit is
defined as TAD. A minimum wait of 2 TAD is
required before the next acquisition starts.
A/D BLOCK DIAGRAM
CHS2:CHS0
110
101
RB7/AN6/PGD/T1OSI
RB6/AN5/PGC/T1OSO/T1CKI
100
RA4/AN4/T0CKI/C2OUT
011
RA3/AN3/VREF+/C1OUT
010
VIN
RA2/AN2/CVREF/VREF-
(Input Voltage)
001
RA1/AN1
AVDD
A/D
Converter
000
RA0/AN0
VREF+
(Reference
Voltage)
VCFG1:VCFG0
VREF(Reference
Voltage)
AVSS
VCFG1:VCFG0
DS30487B-page 116
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
12.1
A/D Acquisition Requirements
For the A/D converter to meet its specified accuracy,
the charge holding capacitor (CHOLD) must be allowed
to fully charge to the input channel voltage level. The
analog input model is shown in Figure 12-2. The
source impedance (RS) and the internal sampling
switch (RSS) impedance directly affect the time
required to charge the capacitor CHOLD. The sampling
switch (RSS) impedance varies over the device voltage
(VDD), see Figure 12-2. The maximum recommended impedance for analog sources is 2.5 kΩ.
As the impedance is decreased, the acquisition time
EQUATION 12-1:
TACQ
TC
TACQ
may be decreased. After the analog input channel is
selected (changed), this acquisition must be done
before the conversion can be started.
To calculate the minimum acquisition time,
Equation 12-1 may be used. This equation assumes
that 1/2 LSb error is used (1024 steps for the A/D). The
1/2 LSb error is the maximum error allowed for the A/D
to meet its specified resolution.
To calculate the minimum acquisition time, TACQ, see
the PICmicro® Mid-Range Reference Manual
(DS33023).
ACQUISITION TIME
= Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient
=
=
=
=
=
=
=
TAMP + TC + TCOFF
2 µs + TC + [(Temperature -25°C)(0.05 µs/°C)]
CHOLD (RIC + RSS + RS) In(1/2047)
-120 pF (1 kΩ + 7 kΩ + 10 kΩ) In(0.0004885)
16.47 µs
2 µs + 16.47 µs + [(50°C – 25°C)(0.05 µs/°C)
19.72 µs
Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out.
2: The charge holding capacitor (CHOLD) is not discharged after each conversion.
3: The maximum recommended impedance for analog sources is 10 kΩ. This is required to meet the pin
leakage specification.
4: After a conversion has completed, a 2.0 TAD delay must complete before acquisition can begin again.
During this time, the holding capacitor is not connected to the selected A/D input channel.
FIGURE 12-2:
ANALOG INPUT MODEL
VDD
Rs
ANx
VA
CPIN
5 pF
VT = 0.6V
VT = 0.6V
Sampling
Switch
RIC ≤ 1k
SS
RSS
CHOLD
= DAC capacitance
= 51.2 pF
I leakage
± 500 nA
VSS
Legend: CPIN
= input capacitance
= threshold voltage
VT
I leakage = leakage current at the pin due to
various junctions
= interconnect resistance
RIC
SS
= sampling switch
CHOLD
= sample/hold capacitance (from DAC)
 2003 Microchip Technology Inc.
Preliminary
6V
5V
VDD 4 V
3V
2V
5 6 7 8 9 10 11
Sampling Switch
(kΩ)
DS30487B-page 117
PIC16F87/88
12.2
Selecting the A/D Conversion
Clock
12.3
The A/D conversion time per bit is defined as TAD. The
A/D conversion requires 9.0 TAD per 8-bit conversion.
The source of the A/D conversion clock is software
selectable. The seven possible options for TAD are:
•
•
•
•
•
•
•
2 TOSC
4 TOSC
8 TOSC
16 TOSC
32 TOSC
64 TOSC
Internal A/D module RC oscillator (2-6 µs)
The ADCON1, ANSEL, TRISA, and TRISB registers
control the operation of the A/D port pins. The port pins
that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is
cleared (output), the digital output level (VOH or VOL)
will be converted.
The A/D operation is independent of the state of the
CHS<2:0> bits and the TRIS bits.
For correct A/D conversions, the A/D conversion clock
(TAD) must be selected to ensure a minimum TAD time
as small as possible, but no less than 1.6 µs and not
greater than 6.4 µs.
Note 1: When reading the port register, all pins
configured as analog input channels will
read as cleared (a low level). Pins configured as digital inputs will convert an analog input. Analog levels on a digitally
configured input will not affect the
conversion accuracy.
2: Analog levels on any pin that is defined as
a digital input (including the RA4:RA0 and
RB7:RB6 pins), may cause the input
buffer to consume current out of the
device specification.
Table 12-1 shows the resultant TAD times derived from
the device operating frequencies and the A/D clock
source selected.
TABLE 12-1:
Configuring Analog Port Pins
TAD vs. MAXIMUM DEVICE OPERATING FREQUENCIES – STANDARD DEVICES (C)
AD Clock Source (TAD)
Maximum Device Frequency
Operation
ADCS<2>
ADCS<1:0>
Max.
2 TOSC
0
00
1.25 MHz
4 TOSC
1
00
2.5 MHz
8 TOSC
0
01
5 MHz
16 TOSC
1
01
10 MHz
32 TOSC
0
10
20 MHz
64 TOSC
1
10
20 MHz
(1,2,3)
X
11
(Note 1)
RC
Note 1:
2:
3:
time of 4 µs, but can vary between 2-6 µs.
The RC source has a typical
When the device frequencies are greater than 1 MHz, the RC A/D conversion clock source is only
recommended for SLEEP operation.
For extended voltage devices (LF), please refer to Section 18.0 “Electrical Characteristics”.
DS30487B-page 118
TAD
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
12.4
12.4.1
A/D Conversions
A/D RESULT REGISTERS
The ADRESH:ADRESL register pair is the location
where the 10-bit A/D result is loaded at the completion
of the A/D conversion. This register pair is 16 bits wide.
The A/D module gives the flexibility to left or right justify
the 10-bit result in the 16-bit result register. The A/D
Format Select bit (ADFM) controls this justification.
Figure 12-4 shows the operation of the A/D result
justification. The extra bits are loaded with ‘0’s. When
an A/D result will not overwrite these locations (A/D disable), these registers may be used as two general
purpose 8-bit registers.
Clearing the GO/DONE bit during a conversion will
abort the current conversion. The A/D result register
pair will NOT be updated with the partially completed
A/D conversion sample. That is, the ADRESH:ADRESL
registers will continue to contain the value of the last
completed conversion (or the last value written to the
ADRESH:ADRESL registers). After the A/D conversion
is aborted, a 2 TAD wait is required before the next
acquisition is started. After this 2 TAD wait, acquisition
on the selected channel is automatically started. The
GO/DONE bit can then be set to start the conversion.
In Figure 12-3, after the GO bit is set, the first time
segment has a minimum of TCY and a maximum of TAD.
Note:
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
FIGURE 12-3:
A/D CONVERSION TAD CYCLES
TCY to TAD TAD1
TAD2
TAD3
TAD4
TAD5
TAD6
TAD7
TAD8
b9
b8
b7
b6
b5
b4
b3
TAD9 TAD10 TAD11
b2
b1
b0
Conversion starts
Holding capacitor is disconnected from analog input (typically 100 ns)
Set GO bit
FIGURE 12-4:
ADRES is loaded,
GO bit is cleared,
ADIF bit is set,
holding capacitor is connected to analog input
A/D RESULT JUSTIFICATION
10-bit Result
ADFM = 0
ADFM = 1
7
0
2107
7
0765
0000 00
ADRESH
ADRESL
ADRESH
10-bit Result
ADRESL
10-bit Result
Left Justified
Right Justified
 2003 Microchip Technology Inc.
0
0000 00
Preliminary
DS30487B-page 119
PIC16F87/88
12.5
A/D Operation During SLEEP
12.6
The A/D module can operate during SLEEP mode. This
requires that the A/D clock source be set to RC
(ADCS1:ADCS0 = 11). When the RC clock source is
selected, the A/D module waits one instruction cycle
before starting the conversion. This allows the SLEEP
instruction to be executed, which eliminates all digital
switching noise from the conversion. When the conversion is completed, the GO/DONE bit will be cleared and
the result loaded into the ADRES register. If the A/D
interrupt is enabled, the device will wake-up from
SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will
remain set.
A device RESET forces all registers to their RESET
state. The A/D module is disabled and any conversion
in progress is aborted. All A/D input pins are configured
as analog inputs.
The value that is in the ADRESH:ADRESL registers
is not modified for a Power-on Reset. The
ADRESH:ADRESL registers will contain unknown data
after a Power-on Reset.
12.7
Turning off the A/D places the A/D module in its lowest
current consumption state.
For the A/D module to operate in SLEEP,
the A/D clock source must be set to RC
(ADCS1:ADCS0 = 11). To perform an A/D
conversion in SLEEP, ensure the SLEEP
instruction immediately follows the
instruction that sets the GO/DONE bit.
TABLE 12-2:
Use of the CCP Trigger
An A/D conversion can be started by the “special event
trigger” of the CCP module. This requires that the
CCP1M3:CCP1M0 bits (CCP1CON<3:0>) be programmed as ‘1011’ and that the A/D module is enabled
(ADON bit is set). When the trigger occurs, the GO/
DONE bit will be set, starting the A/D conversion and
the Timer1 counter will be reset to zero. Timer1 is reset
to automatically repeat the A/D acquisition period with
minimal
software
overhead
(moving
the
ADRESH:ADRESL to the desired location). The appropriate analog input channel must be selected and the
minimum acquisition done before the “special event
trigger” sets the GO/DONE bit (starts a conversion).
When the A/D clock source is another clock option (not
RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off,
though the ADON bit will remain set.
Note:
Effects of a RESET
If the A/D module is not enabled (ADON is cleared), then
the “special event trigger” will be ignored by the A/D
module, but will still reset the Timer1 counter.
REGISTERS/BITS ASSOCIATED WITH A/D
Value on
all other
RESETS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
0Bh, 8Bh INTCON
10Bh, 18Bh
GIE
PEIE
TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF
0000 000x 0000 000u
Address
0Ch
PIR1
—
ADIF
RCIF
TXIF
SSPIF
CCP1IF
TMR2IF TMR1IF
-000 0000 -000 0000
8Ch
PIE1
—
ADIE
RCIE
TXIE
SSPIE
CCP1IE
TMR2IE TMR1IE
-000 0000 -000 0000
1Eh
ADRESH(1) A/D Result Register High Byte
xxxx xxxx uuuu uuuu
9Eh
ADRESL(1) A/D Result Register Low Byte
xxxx xxxx uuuu uuuu
1Fh
ADCON0(1)
9Fh
ADCON1(1) ADFM
(1)
ADCS1 ADCS0
ADCS2
CHS2
CHS1
VCFG1
VCFG0
CHS0 GO/DONE
—
—
—
ADON
0000 00-0 0000 00-0
—
—
0000 ---- 0000 ----111 1111 -111 1111
9Bh
ANSEL
—
AN6
AN5
AN4
AN3
AN2
AN1
AN0
05h
PORTA
(PIC16F87)
(PIC16F88)
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
05h, 106h PORTB
(PIC16F87)
(PIC16F88)
RB7
85h
TRISA
86h, 186h TRISB
Legend:
Note 1:
2:
xxxx 0000 uuuu 0000
xxx0 0000 uuu0 0000
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx uuuu uuuu
00xx xxxx 00uu uuuu
TRISA7 TRISA6 TRISA5(2) PORTA Data Direction Register
TRISB7 TRISB6
TRISB5 TRISB4 TRISB3
TRISB2
TRISB1
1111 1111 1111 1111
TRISB0
1111 1111 1111 1111
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
PIC16F88 only.
Pin 5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
DS30487B-page 120
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
13.0
COMPARATOR MODULE
The comparator module contains two analog
comparators. The inputs to the comparators are multiplexed with I/O port pins RA0 through RA3, while the
outputs are multiplexed to pins RA3 and RA4. The onchip Voltage Reference (Section 14.0 “Comparator
Voltage Reference Module”) can also be an input to
the comparators.
REGISTER 13-1:
The CMCON register (Register 13-1) controls the comparator input and output multiplexers. A block diagram
of the various comparator configurations is shown in
Figure 13-1.
CMCON REGISTER (ADDRESS 9Ch)
R-0
R-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
bit 7
bit 0
bit 7
C2OUT: Comparator 2 Output bit
When C2INV = 0:
1 = C2 VIN+ > C2 VIN0 = C2 VIN+ < C2 VINWhen C2INV = 1:
1 = C2 VIN+ < C2 VIN0 = C2 VIN+ > C2 VIN-
bit 6
C1OUT: Comparator 1 Output bit
When C1INV = 0:
1 = C1 VIN+ > C1 VIN0 = C1 VIN+ < C1 VINWhen C1INV = 1:
1 = C1 VIN+ < C1 VIN0 = C1 VIN+ > C1 VIN-
bit 5
C2INV: Comparator 2 Output Inversion bit
1 = C2 output inverted
0 = C2 output not inverted
bit 4
C1INV: Comparator 1 Output Inversion bit
1 = C1 output inverted
0 = C1 output not inverted
bit 3
CIS: Comparator Input Switch bit
When CM2:CM0 = 001:
1 = C1 VIN- connects to RA3
0 = C1 VIN- connects to RA0
When CM2:CM0 = 010:
1 = C1 VIN- connects to RA3
C2 VIN- connects to RA2
0 = C1 VIN- connects to RA0
C2 VIN- connects to RA1
bit 2-0
CM<2:0>: Comparator Mode bits
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
- n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 121
PIC16F87/88
13.1
Comparator Configuration
Note:
Comparator interrupts should be disabled
during a Comparator mode change.
Otherwise, a false interrupt may occur.
There are eight modes of operation for the comparators. The CMCON register is used to select these
modes. Figure 13-1 shows the eight possible modes.
The TRISA register controls the data direction of the
comparator pins for each mode. If the Comparator
mode is changed, the comparator output level may not
be valid for the specified mode change delay shown in
Section 18.0 “Electrical Characteristics”.
FIGURE 13-1:
COMPARATOR I/O OPERATING MODES
Comparators Reset
CM2:CM0 = 000
RA0/AN0
RA3/AN3
RA1/AN1
RA2/AN2
A
Comparators Off (POR Default Value)
CM2:CM0 = 111
VIN-
A
VIN+
A
VIN-
A
VIN+
RA0/AN0
C1
Off (Read as ‘0’)
RA1/AN1
C2
Off (Read as ‘0’)
RA3/AN3
RA1/AN1
RA2/AN2
A
VIN-
A
VIN+
A
A
RA0/AN0
C1
C1OUT
RA3/AN3
RA1/AN1
VINVIN+
RA2/AN2
C2
VIN-
D
VIN+
D
VIN-
D
VIN+
C1
Off (Read as ‘0’)
C2
Off (Read as ‘0’)
Four Inputs Multiplexed to Two Comparators
CM2:CM0 = 010
Two Independent Comparators
CM2:CM0 = 100
RA0/AN0
RA3/AN3
D
RA2/AN2
C2OUT
A
A
CIS = 0
CIS = 1
VINVIN+
C1
C1OUT
C2
C2OUT
A
A
VIN-
CIS = 0
CIS = 1
VIN+
From VREF Module
Two Common Reference Comparators with Outputs
CM2:CM0 = 110
Two Common Reference Comparators
CM2:CM0 = 011
RA0/AN0
RA3/AN3
RA1/AN1
RA2/AN2
A
VIN-
D
VIN+
A
VIN-
A
VIN+
RA0/AN0
C1
C1OUT
C2
C2OUT
RA3/AN3
RA1/AN1
RA2/AN2
A
VIN-
D
VIN+
A
VIN-
A
VIN+
C1
C1OUT
C2
C2OUT
RA4/T0CKI
One Independent Comparator
CM2:CM0 = 101
RA0/AN0
RA3/AN3
RA1/AN1
RA2/AN2
D
D
Three Inputs Multiplexed to Two Comparators
CM2:CM0 = 001
VINVIN+
A
VIN-
A
VIN+
RA0/AN0
C1
Off (Read as ‘0’)
RA3/AN3
RA1/AN1
C2
C2OUT
RA2/AN2
A
A
CIS = 0
CIS = 1
VINVIN+
A
VIN-
A
VIN+
C1
C1OUT
C2
C2OUT
A = Analog Input, port reads zeros always.
D = Digital Input.
CIS (CMCON<3>) is the Comparator Input Switch.
DS30487B-page 122
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
13.2
13.3.2
Comparator Operation
A single comparator is shown in Figure 13-2, along with
the relationship between the analog input levels and
the digital output. When the analog input at VIN+ is less
than the analog input VIN-, the output of the comparator
is a digital low level. When the analog input at VIN+ is
greater than the analog input VIN-, the output of the
comparator is a digital high level. The shaded areas of
the output of the comparator in Figure 13-2 represent
the uncertainty due to input offsets and response time.
13.3
Comparator Reference
FIGURE 13-2:
SINGLE COMPARATOR
VIN+
+
VIN-
–
The comparator module also allows the selection of an
internally generated voltage reference for the
comparators. Section 14.0 “Comparator Voltage
Reference Module” contains a detailed description of
the Comparator Voltage Reference module that provides this signal. The internal reference signal is used
when comparators are in mode CM<2:0> = 110
(Figure 13-1). In this mode, the internal voltage
reference is applied to the VIN+ pin of both
comparators.
13.4
An external or internal reference signal may be used
depending on the comparator operating mode. The
analog signal present at VIN- is compared to the signal
at VIN+, and the digital output of the comparator is
adjusted accordingly (Figure 13-2).
Comparator Response Time
Response time is the minimum time, after selecting a
new reference voltage or input source, before the
comparator output has a valid level. If the internal
reference is changed, the maximum delay of the internal voltage reference must be considered when using
the comparator outputs. Otherwise, the maximum
delay of the comparators should be used (Section 18.0
“Electrical Characteristics”).
13.5
Output
INTERNAL REFERENCE SIGNAL
Comparator Outputs
The comparator outputs are read through the CMCON
register. These bits are read only. The comparator
outputs may also be directly output to the RA3 and RA4
I/O pins. When enabled, multiplexors in the output path
of the RA3 and RA4 pins will switch and the output of
each pin will be the unsynchronized output of the comparator. The uncertainty of each of the comparators is
related to the input offset voltage and the response time
given in the specifications. Figure 13-3 shows the
comparator output block diagram.
VIN
VIN–
VIN
+
VIN+
The TRISA bits will still function as an output enable/
disable for the RA3 and RA4 pins while in this mode.
Output
Output
The polarity of the comparator outputs can be changed
using the C2INV and C1INV bits (CMCON<4:5>).
13.3.1
EXTERNAL REFERENCE SIGNAL
When external voltage references are used, the
comparator module can be configured to have the comparators operate from the same, or different reference
sources. However, threshold detector applications may
require the same reference. The reference signal must
be between VSS and VDD, and can be applied to either
pin of the comparator(s).
 2003 Microchip Technology Inc.
Note 1: When reading the PORT register, all pins
configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert an analog input, according to the
Schmitt Trigger input specification.
Preliminary
2: Analog levels, on any pin defined as a
digital input, may cause the input buffer to
consume more current than is specified.
DS30487B-page 123
PIC16F87/88
FIGURE 13-3:
COMPARATOR OUTPUT BLOCK DIAGRAM
Port Pins
MULTIPLEX
CnINV
To Data Bus
Q
D
Q1
EN
RD_CMCON
Q
Set CMIF bit
D
Q3 * RD_CMCON
EN
CL
From other Comparator
13.6
NRESET
Comparator Interrupts
Note:
The comparator interrupt flag is set whenever there is
a change in the output value of either comparator.
Software will need to maintain information about the
status of the output bits, as read from CMCON<7:6>, to
determine the actual change that occurred. The CMIF
bit (PIR registers) is the comparator interrupt flag. The
CMIF bit must be reset by clearing it (‘0’). Since it is
also possible to write a ‘1’ to this register, a simulated
interrupt may be initiated.
The CMIE bit (PIE registers) and the PEIE bit (INTCON
register) must be set to enable the interrupt. In addition,
the GIE bit must also be set. If any of these bits are
clear, the interrupt is not enabled, though the CMIF bit
will still be set if an interrupt condition occurs.
DS30487B-page 124
If a change in the CMCON register
(C1OUT or C2OUT) should occur when a
read operation is being executed (start of
the Q2 cycle), then the CMIF (PIR
registers) interrupt flag may not get set.
The user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
Any read or write of CMCON will end the
mismatch condition.
Clear flag bit CMIF.
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition, and
allow flag bit CMIF to be cleared.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
13.7
Comparator Operation During
SLEEP
13.9
When a comparator is active and the device is placed
in SLEEP mode, the comparator remains active and
the interrupt is functional, if enabled. This interrupt will
wake-up the device from SLEEP mode when enabled.
While the comparator is powered up, higher SLEEP
currents than shown in the power-down current
specification will occur. Each operational comparator
will consume additional current, as shown in the comparator specifications. To minimize power consumption
while in SLEEP mode, turn off the comparators,
CM<2:0> = 111, before entering SLEEP. If the device
wakes up from SLEEP, the contents of the CMCON
register are not affected.
13.8
Analog Input Connection
Considerations
A simplified circuit for an analog input is shown in
Figure 13-4. Since the analog pins are connected to a
digital output, they have reverse biased diodes to VDD
and VSS. The analog input, therefore, must be between
VSS and VDD. If the input voltage deviates from this
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latch-up condition may
occur. A maximum source impedance of 10 kΩ is recommended for the analog sources. Any external component connected to an analog input pin, such as a
capacitor or a Zener diode, should have very little
leakage current.
Effects of a RESET
A device RESET forces the CMCON register to its
RESET state, causing the comparator module to be in
the Comparator Off mode, CM<2:0> = 111.
FIGURE 13-4:
ANALOG INPUT MODEL
VDD
VT = 0.6V
RS < 10K
RIC
AIN
CPIN
5 pF
VA
VT = 0.6V
ILEAKAGE
±500 nA
VSS
Legend:
CPIN
VT
ILEAKAGE
RIC
RS
VA
 2003 Microchip Technology Inc.
=
=
=
=
=
=
Input Capacitance
Threshold Voltage
Leakage Current at the pin due to various junctions
Interconnect Resistance
Source Impedance
Analog Voltage
Preliminary
DS30487B-page 125
PIC16F87/88
TABLE 13-1:
Address
REGISTERS ASSOCIATED WITH THE COMPARATOR MODULE
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR
Value on
all other
RESETS
9Ch
CMCON
C2OUT
C1OUT
C2INV
C1INV
CIS
CM2
CM1
CM0
9Dh
CVRCON
CVREN CVROE
CVRR
—
CVR3
CVR2
CVR1
CVR0
000- 0000 000- 0000
PEIE
TMR0IE
INTIE
RBIE
TMR0IF
INTIF
RBIF
0000 000x 0000 000u
0Bh, 8Bh, INTCON
10Bh, 18Bh
GIE
0000 0111 0000 0111
0Dh
PIR2
OSFIF
CMIF
—
EEIF
—
—
—
—
00-0 ---- 00-0 ----
8Dh
PIE2
OSFIE
CMIE
—
EEIE
—
—
—
—
00-0 ---- 00-0 ----
05h
PORTA
(PIC16F87)
(PIC16F88)
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
xxxx 0000 uuuu 0000
xxx0 0000 uuu0 0000
TRISA7
TRISA6 TRISA5(1) TRISA4 TRISA3 TRISA2 TRISA1
TRISA0 1111 1111 1111 1111
85h
TRISA
Legend:
Note 1:
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are unused by the comparator module.
Pin 5 is an input only; the state of the TRISA5 bit has no effect and will always read ‘1’.
DS30487B-page 126
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
14.0
COMPARATOR VOLTAGE
REFERENCE MODULE
The Comparator Voltage Reference Generator is a 16tap resistor ladder network that provides a fixed voltage
reference when the comparators are in mode ‘110’. A
programmable register controls the function of the reference generator. Register 14-1 lists the bit functions of
the CVRCON register.
As shown in Figure 14-1, the resistor ladder is segmented to provide two ranges of CVREF values and has
a power-down function to conserve power when the
reference is not being used. The comparator reference
REGISTER 14-1:
supply voltage (also referred to as CVRSRC) comes
directly from VDD. It should be noted, however, that the
voltage at the top of the ladder is CVRSRC – VSAT,
where VSAT is the saturation voltage of the power
switch transistor. This reference will only be as
accurate as the values of CVRSRC and VSAT.
The output of the reference generator may be connected to the RA2/AN2/CVREF/VREF- pin. This can be
used as a simple D/A function by the user, if a very
high-impedance load is used. The primary purpose of
this function is to provide a test path for testing the
reference generator function.
CVRCON CONTROL REGISTER (ADDRESS 9Dh)
R/W-0
CVREN
bit 7
R/W-0
CVROE
R/W-0
CVRR
U-0
—
R/W-0
CVR3
R/W-0
CVR2
R/W-0
CVR1
bit 7
CVREN: Comparator Voltage Reference Enable bit
1 = CVREF circuit powered on
0 = CVREF circuit powered down
bit 6
CVROE: Comparator VREF Output Enable bit
1 = CVREF voltage level is output on the RA2/AN2/CVREF/VREF- pin
0 = CVREF voltage level is disconnected from the RA2/AN2/CVREF/VREF- pin
bit 5
CVRR: Comparator VREF Range Selection bit
1 = 0.00 CVRSRC to 0.75 CVRSRC with CVRSRC/24 step size
0 = 0.25 CVRSRC to 0.75 CVRSRC with CVRSRC/32 step size
bit 4
Unimplemented: Read as ‘0’
bit 3-0
CVR<3:0>: Comparator VREF Value Selection 0 ≤ VR3:VR0 ≤ 15 bits
When CVRR = 1:
CVREF = (VR<3:0>/24) • (CVRSRC)
When CVRR = 0:
CVREF = 1/4 • (CVRSRC) + (VR3:VR0/32) • (CVRSRC)
R/W-0
CVR0
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 127
PIC16F87/88
FIGURE 14-1:
COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
VDD
16 Stages
CVREN
8R
R
R
R
R
8R
CVRR
RA2/AN2/CVREF/VREF- pin
CVROE
CVREF
Input to
Comparator
TABLE 14-1:
Address
CVR3
CVR2
CVR1
CVR0
16-1 Analog MUX
REGISTERS ASSOCIATED WITH COMPARATOR VOLTAGE REFERENCE
Name
Bit 7
Bit 6
9Dh
CVRCON
CVREN
CVROE
9Ch
CMCON
C2OUT
C1OUT
Legend:
x = unknown, u = unchanged, - = unimplemented, read as ‘0’.
Shaded cells are not used with the comparator voltage reference.
DS30487B-page 128
Bit 5
Value on
POR
Value on
all other
RESETS
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CVRR
—
CVR3
CVR2
CVR1
CVR0
000- 0000 000- 0000
C2INV
C1INV
CIS
CM2
CM1
CM0
0000 0111 0000 0111
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.0
SPECIAL FEATURES OF THE
CPU
These devices have a host of features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving
operating modes and offer code protection:
• RESET
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Two-Speed Start-up
• Fail-Safe Clock Monitor
• SLEEP
• Code Protection
• ID Locations
• In-Circuit Serial Programming™ (ICSP™)
SLEEP mode is designed to offer a very low current
Power-down mode. The user can wake-up from
SLEEP through external RESET, Watchdog Timer
Wake-up, or through an interrupt.
Additional information on special features is available
in the PICmicro® Mid-Range Reference Manual
(DS33023).
15.1
Configuration Bits
The configuration bits can be programmed (read as
‘0’), or left unprogrammed (read as ‘1’), to select various device configurations. These bits are mapped in
program memory locations 2007h and 2008h.
The user will note that address 2007h is beyond the
user program memory space, which can be accessed
only during programming.
There are two timers that offer necessary delays on
power-up. One is the Oscillator Start-up Timer (OST),
intended to keep the chip in RESET until the crystal
oscillator is stable. The other is the Power-up Timer
(PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only. It is designed to keep the part in
RESET while the power supply stabilizes, and is
enabled or disabled using a configuration bit. With
these two timers on-chip, most applications need no
external RESET circuitry.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 129
PIC16F87/88
REGISTER 15-1:
R/P-1
CP
R/P-1
CONFIG1: CONFIGURATION WORD 1 REGISTER (ADDRESS 2007h)
R/P-1
R/P-1
R/P-1
R/P-1 R/P-1
CCPMX RESV WRT1 WRT0
CPD
LVP
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
R/P-1
BOREN MCLRE FOSC2 PWRTEN WDTEN FOSC1 FOSC0
bit 13
bit 0
bit 13
CP: FLASH Program Memory Code Protection bits
1 = Code protection off
0 = 0000h to 0FFFh code protected (All protected)
bit 12
CCPMX: CCP1 Pin Selection bit
1 = CCP1 function on RB0
0 = CCP1 function on RB3
bit 11
DEBUG: In-Circuit Debugger Mode bit
1 = In-circuit debugger disabled, RB6 and RB7 are general purpose I/O pins
0 = In-circuit debugger enabled, RB6 and RB7 are dedicated to the debugger
bit 10-9 WRT<1:0>: FLASH Program Memory Write Enable bits
11 = Write protection off
10 = 0000h to 00FFh write protected, 0100h to 0FFFh may be modified by EECON control
01 = 0000h to 07FFh write protected, 0800h to 0FFFh may be modified by EECON control
00 = 0000h to 0FFFh write protected
bit 8
CPD: Data EE Memory Code Protection bit
1 = Code protection off
0 = Data EE memory code protected
bit 7
LVP: Low-Voltage Programming Enable bit
1 = RB3/PGM pin has PGM function, low-voltage programming enabled
0 = RB3 is digital I/O, HV on MCLR must be used for programming
bit 6
BOREN: Brown-out Reset Enable bit
1 = BOR enabled
0 = BOR disabled
bit 5
MCLRE: RA5/MCLR Pin Function Select bit
1 = RA5/MCLR pin function is MCLR
0 = RA5/MCLR pin function is digital I/O, MCLR internally tied to VDD
bit 3
PWRTEN: Power-up Timer Enable bit
1 = PWRT disabled
0 = PWRT enabled
bit 2
WDTEN: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
bit 4, 1-0 FOSC<2:0>: Oscillator Selection bits
111 = EXTRC oscillator; CLKO function on RA6/OSC2/CLKO
110 = EXTRC oscillator; port I/O function on RA6/OSC2/CLKO
101 = INTRC oscillator; CLKO function on RA6/OSC2/CLKO pin and port I/O function on RA7/OSC1/CLKI pin
100 = INTRC oscillator; port I/O function on both RA6/OSC2/CLKO pin and RA7/OSC1/CLKI pin
011 = EXTCLK; port I/O function on RA6/OSC2/CLKO
010 = HS oscillator
001 = XT oscillator
000 = LP oscillator
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
DS30487B-page 130
Preliminary
x = Bit is unknown
 2003 Microchip Technology Inc.
PIC16F87/88
REGISTER 15-2:
CONFIG2: CONFIGURATION WORD 2 REGISTER (ADDRESS 2008h)
U-1
U-1
U-1
U-1
U-1
U-1
U-1
U-1
U-1
U-1
U-1
U-1
R/P-1
R/P-1
—
—
—
—
—
—
—
—
—
—
—
—
IESO
FCMEN
bit 13
bit 0
bit 13-2 Unimplemented: Read as ‘1’
bit 1
IESO: Internal External Switch Over bit
1 = Internal External Switch Over mode enabled
0 = Internal External Switch Over mode disabled
bit 0
FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
 2003 Microchip Technology Inc.
Preliminary
x = Bit is unknown
DS30487B-page 131
PIC16F87/88
15.2
RESET
The PIC16F87/88 differentiates between various kinds
of RESET:
•
•
•
•
•
•
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during SLEEP
WDT Reset during normal operation
WDT Wake-up during SLEEP
Brown-out Reset (BOR)
Some registers are not affected in any RESET condition. Their status is unknown on POR and unchanged
in any other RESET. Most other registers are reset to a
“RESET state” on Power-on Reset (POR), on the
MCLR and WDT Reset, on MCLR Reset during
SLEEP, and Brown-out Reset (BOR). They are not
affected by a WDT wake-up, which is viewed as the
resumption of normal operation. The TO and PD bits
are set or cleared differently in different RESET situations, as indicated in Table 15-3. These bits are used in
software to determine the nature of the RESET. Upon
a POR, BOR, or wake-up from SLEEP, the CPU
requires approximately 5-10 µs to become ready for
code execution. This delay runs in parallel with any
other timers. See Table 15-4 for a full description of
RESET states of all registers.
A simplified block diagram of the on-chip RESET circuit
is shown in Figure 15-1.
FIGURE 15-1:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External
RESET
MCLR
WDT
WDT
Module
SLEEP
Time-out
Reset
VDD Rise
Detect
Power-on Reset
VDD
Brown-out
Reset
S
BOREN
OST/PWRT
OST
Chip_Reset
10-bit Ripple Counter
R
Q
OSC1
PWRT
INTRC
31.25 kHz
11-bit Ripple Counter
Enable PWRT
Enable OST
DS30487B-page 132
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.3
MCLR
PIC16F87/88 devices have a noise filter in the MCLR
Reset path. The filter will detect and ignore small
pulses.
It should be noted that a WDT Reset does not drive
MCLR pin low.
The behavior of the ESD protection on the MCLR pin
has been altered from previous devices of this family.
Voltages applied to the pin, that exceed its specification, can result in both MCLR and excessive current
beyond the device specification during the ESD event.
The circuit, as shown in Figure 15-2, is suggested.
Note:
For this reason, Microchip recommends
that the MCLR pin no longer be tied
directly to VDD.
The RA5/MCLR pin can be configured for MCLR
(default), or as an I/O pin (RA5). This is configured
through the MCLRE bit in Configuration Word 1.
FIGURE 15-2:
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW VDD POWER-UP)
VDD
D
15.5
R1
MCLR
The Power-up Timer (PWRT) of the PIC16F87/88 is a
counter that uses the INTRC oscillator as the clock
input. This yields a count of 72 ms. While the PWRT is
counting, the device is held in RESET.
The power-up time delay depends on the INTRC, and
will vary from chip-to-chip due to temperature and
process variation. See DC parameter #33 for details.
The PWRT is enabled by clearing configuration bit
PWRTEN.
15.6
PIC16F87/88
Note 1: External Power-on Reset circuit is required
only if the VDD power-up slope is too slow.
The diode D helps discharge the capacitor
quickly when VDD powers down.
2: R < 40 kΩ is recommended to make sure that
the voltage drop across R does not violate
the device’s electrical specification.
3: R1 = 1 kΩ to 10 kΩ will limit any current flowing into MCLR from external capacitor C
(0.1 µF), in the event of MCLR/VPP pin breakdown due to Electrostatic Discharge (ESD) or
Electrical Overstress (EOS).
Power-on Reset (POR)
A Power-on Reset pulse is generated on-chip when
VDD rise is detected (in the range of 1.2V-1.7V). To take
advantage of the POR, tie the MCLR pin to VDD, as
described in Section 15.3 “MCLR”. A maximum rise
time for VDD is specified. See Section 18.0 “Electrical
Characteristics” for details.
 2003 Microchip Technology Inc.
Oscillator Start-up Timer (OST)
The Oscillator Start-up Timer (OST) provides 1024
oscillator cycles (from OSC1 input) delay after the
PWRT delay is over (if enabled). This helps to ensure
that the crystal oscillator or resonator has started and
stabilized.
15.7
15.4
Power-up Timer (PWRT)
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset, or wake-up from
SLEEP.
R
C
When the device starts normal operation (exits the
RESET condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure
operation. If these conditions are not met, the device
must be held in RESET until the operating conditions
are met. For more information, see Application Note,
AN607 “Power-up Trouble Shooting” (DS00607).
Brown-out Reset (BOR)
The configuration bit, BOREN, can enable or disable
the Brown-out Reset circuit. If VDD falls below VBOR
(parameter D005, about 4V) for longer than TBOR
(parameter #35, about 100 µs), the brown-out situation
will reset the device. If VDD falls below VBOR for less
than TBOR, a RESET may not occur.
Once the brown-out occurs, the device will remain in
Brown-out Reset until VDD rises above VBOR. The
Power-up Timer (if enabled) will keep the device in
RESET for TPWRT (parameter #33, about 72 ms). If
VDD should fall below VBOR during TPWRT, the Brownout Reset process will restart when VDD rises above
VBOR, with the Power-up Timer Reset. Unlike previous
PIC16 devices, the PWRT is no longer automatically
enabled when the Brown-out Reset circuit is enabled.
The PWRTEN and BOREN configuration bits are
independent of each other.
Preliminary
DS30487B-page 133
PIC16F87/88
15.8
Time-out Sequence
15.9
On power-up, the time-out sequence is as follows: the
PWRT delay starts (if enabled) when a POR occurs.
Then, OST starts counting 1024 oscillator cycles when
PWRT ends (LP, XT, HS). When the OST ends, the
device comes out of RESET.
The Power Control/Status Register, PCON, has two
bits to indicate the type of RESET that last occurred.
Bit0 is Brown-out Reset Status bit, BOR. Bit BOR is
unknown on a Power-on Reset. It must then be set by
the user and checked on subsequent RESETS to see
if bit BOR cleared, indicating a Brown-out Reset
occurred. When the Brown-out Reset is disabled, the
state of the BOR bit is unpredictable.
If MCLR is kept low long enough, all delays will expire.
Bringing MCLR high will begin execution immediately.
This is useful for testing purposes, or to synchronize
more than one PIC16F87/88 device operating in
parallel.
Bit1 is POR (Power-on Reset Status bit). It is cleared on
a Power-on Reset and unaffected otherwise. The user
must set this bit following a Power-on Reset.
Table 15-3 shows the RESET conditions for the
STATUS, PCON and PC registers, while Table 15-4
shows the RESET conditions for all the registers.
TABLE 15-1:
TIME-OUT IN VARIOUS SITUATIONS
Power-up
Oscillator
Configuration
XT, HS, LP
Brown-out Reset
PWRTE = 0
PWRTE = 1
PWRTE = 0
PWRTE = 1
Wake-up from
SLEEP
TPWRT + 1024 • TOSC
1024 • TOSC
TPWRT + 1024 • TOSC
1024 • TOSC
1024 • TOSC
EXTRC, INTRC
TPWRT
T1OSC
Note 1:
Power Control/Status Register
(PCON)
5-10
—
µs(1)
TPWRT
—
5-10
—
µs(1)
—
5-10 µs(1)
5-10 µs(1)
CPU start-up is always invoked on POR, BOR and wake-up from SLEEP. The 5 µs-10 µs delay is based on
a 1 MHz system clock.
TABLE 15-2:
STATUS BITS AND THEIR SIGNIFICANCE
POR
BOR
TO
PD
0
x
1
1
Power-on Reset
0
x
0
x
Illegal, TO is set on POR
0
x
x
0
Illegal, PD is set on POR
1
0
1
1
Brown-out Reset
1
1
0
1
WDT Reset
1
1
0
0
WDT Wake-up
1
1
u
u
MCLR Reset during normal operation
1
1
1
0
MCLR Reset during SLEEP or interrupt wake-up from SLEEP
Legend: u = unchanged, x = unknown
DS30487B-page 134
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 15-3:
RESET CONDITION FOR SPECIAL REGISTERS
Program
Counter
STATUS
Register
PCON
Register
Power-on Reset
000h
0001 1xxx
---- --0x
MCLR Reset during normal operation
000h
000u uuuu
---- --uu
MCLR Reset during SLEEP
000h
0001 0uuu
---- --uu
WDT Reset
000h
0000 1uuu
---- --uu
PC + 1
uuu0 0uuu
---- --uu
000h
0001 1uuu
---- --u0
uuu1 0uuu
---- --uu
Condition
WDT Wake-up
Brown-out Reset
(1)
Interrupt Wake-up from SLEEP
PC + 1
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’
Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector
(0004h).
TABLE 15-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS
Register
W
Power-on Reset,
Brown-out Reset
xxxx xxxx
INDF
N/A
TMR0
xxxx xxxx
MCLR Reset,
WDT Reset
uuuu uuuu
N/A
uuuu uuuu
Wake-up via WDT or
Interrupt
uuuu uuuu
N/A
uuuu uuuu
0000h
0000h
PC + 1(2)
STATUS
0001 1xxx
000q quuu(3)
uuuq quuu(3)
FSR
xxxx xxxx
uuuu uuuu
uuuu uuuu
PORTA (PIC16F87)
PORTA (PIC16F88)
xxxx 0000
xxx0 0000
uuuu 0000
uuu0 0000
uuuu uuuu
uuuu uuuu
PORTB (PIC16F87)
PORTB (PIC16F87)
xxxx xxxx
00xx xxxx
uuuu uuuu
00uu uuuu
uuuu uuuu
uuuu uuuu
PCLATH
---0 0000
---0 0000
---u uuuu
INTCON
0000 000x
0000 000u
uuuu uuuu(1)
PIR1
-000 0000
-000 0000
-uuu uuuu(1)
PIR2
00-0 ----
00-0 ----
uu-u ----(1)
TMR1L
xxxx xxxx
uuuu uuuu
uuuu uuuu
TMR1H
xxxx xxxx
uuuu uuuu
uuuu uuuu
T1CON
-000 0000
-uuu uuuu
-uuu uuuu
TMR2
0000 0000
0000 0000
uuuu uuuu
T2CON
-000 0000
-000 0000
-uuu uuuu
SSPBUF
xxxx xxxx
uuuu uuuu
uuuu uuuu
SSPCON
0000 0000
0000 0000
uuuu uuuu
CCPR1L
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCPR1H
xxxx xxxx
uuuu uuuu
uuuu uuuu
CCP1CON
--00 0000
--00 0000
--uu uuuu
RCSTA
0000 000x
0000 000x
uuuu uuuu
PCL
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition,
r = reserved, maintain clear
Note 1: One or more bits in INTCON, PIR1 and PR2 will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector
(0004h).
3: See Table 15-3 for RESET value for specific condition.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 135
PIC16F87/88
TABLE 15-4:
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register
Power-on Reset,
Brown-out Reset
MCLR Reset,
WDT Reset
Wake-up via WDT or
Interrupt
TXREG
0000 0000
0000 0000
uuuu uuuu
RCREG
0000 0000
0000 0000
uuuu uuuu
ADRESH
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADCON0
0000 00-0
0000 00-0
uuuu uu-u
OPTION
1111 1111
1111 1111
uuuu uuuu
TRISA
1111 1111
1111 1111
uuuu uuuu
TRISB
1111 1111
1111 1111
uuuu uuuu
PIE1
-000 0000
-000 0000
-uuu uuuu
PIE2
00-0 ----
00-0 ----
uu-u ----
PCON
---- --qq
---- --uu
---- --uu
OSCCON
-000 0000
-000 0000
-uuu uuuu
OSCTUNE
--00 0000
--00 0000
--uu uuuu
PR2
1111 1111
1111 1111
1111 1111
SSPADD
0000 0000
0000 0000
uuuu uuuu
SSPSTAT
0000 0000
0000 0000
uuuu uuuu
TXSTA
0000 -010
0000 -010
uuuu -u1u
SPBRG
0000 0000
0000 0000
uuuu uuuu
ANSEL
-111 1111
-111 1111
-111 1111
CMCON
0000 0111
0000 0111
uuuu u111
CVRCON
000- 0000
000- 0000
uuu- uuuu
WDTCON
---0 1000
---0 1000
---u uuuu
ADRESL
xxxx xxxx
uuuu uuuu
uuuu uuuu
ADCON1
0000 ----
0000 ----
uuuu ----
EEDATA
xxxx xxxx
uuuu uuuu
uuuu uuuu
EEADR
xxxx xxxx
uuuu uuuu
uuuu uuuu
EEDATH
--xx xxxx
--uu uuuu
--uu uuuu
EEADRH
---- -xxx
---- -uuu
---- -uuu
EECON1
x--x x000
u--x u000
u--u uuuu
EECON2
---- ----
---- ----
---- ----
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition,
r = reserved, maintain clear
Note 1: One or more bits in INTCON, PIR1 and PR2 will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector
(0004h).
3: See Table 15-3 for RESET value for specific condition.
DS30487B-page 136
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 15-3:
TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD THROUGH
PULL-UP RESISTOR)
VDD
MCLR
INTERNAL POR
TPWRT
TOST
PWRT TIME-OUT
OST TIME-OUT
INTERNAL RESET
FIGURE 15-4:
TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD THROUGH
RC NETWORK): CASE 1
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
FIGURE 15-5:
TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD THROUGH
RC NETWORK): CASE 2
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 137
PIC16F87/88
FIGURE 15-6:
SLOW RISE TIME (MCLR TIED TO VDD THROUGH RC NETWORK)
5V
VDD
1V
0V
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
15.10 Interrupts
The PIC16F87/88 has up to 12 sources of interrupt.
The Interrupt Control register (INTCON) records individual interrupt requests in flag bits. It also has
individual and global interrupt enable bits.
Note:
Individual interrupt flag bits are set,
regardless of the status of their
corresponding mask bit or the GIE bit.
A global interrupt enable bit, GIE (INTCON<7>),
enables (if set) all unmasked interrupts, or disables (if
cleared) all interrupts. When bit GIE is enabled, and an
interrupt’s flag bit and mask bit are set, the interrupt will
vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt bits are set
regardless of the status of the GIE bit. The GIE bit is
cleared on RESET.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine, as well as sets the GIE bit, which
re-enables interrupts.
DS30487B-page 138
The RB0/INT pin interrupt, the RB port change interrupt
and the TMR0 overflow interrupt flags are contained in
the INTCON register.
The peripheral interrupt flags are contained in the
Special Function Register, PIR1. The corresponding
interrupt enable bits are contained in Special Function
Register, PIE1, and the peripheral interrupt enable bit
is contained in Special Function Register, INTCON.
When an interrupt is serviced, the GIE bit is cleared to
disable any further interrupt, the return address is
pushed onto the stack, and the PC is loaded with
0004h. Once in the Interrupt Service Routine, the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bit(s) must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
For external interrupt events, such as the INT pin or
PORTB change interrupt, the interrupt latency will be
three or four instruction cycles. The exact latency
depends on when the interrupt event occurs, relative to
the current Q cycle. The latency is the same for one or
two cycle instructions. Individual interrupt flag bits are
set, regardless of the status of their corresponding
mask bit, PEIE bit or the GIE bit.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 15-7:
INTERRUPT LOGIC
EEIF
EEIE
OSFIF
OSFIE
ADIF
ADIE
TMR0IF
TMR0IE
RCIF
RCIE
TXIF
TXIE
SSPIF
SSPIE
CCP1IF
CCP1IE
INTF
INTE
Wake-up (If in SLEEP mode)
Interrupt to CPU
RBIF
RBIE
PEIE
GIE
TMR2IF
TMR2IE
TMR1IF
TMR1IE
CMIF
CMIE
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 139
PIC16F87/88
15.10.1
INT INTERRUPT
15.10.3
External interrupt on the RB0/INT pin is edge-triggered,
either rising, if bit INTEDG (OPTION<6>) is set, or falling, if the INTEDG bit is clear. When a valid edge
appears on the RB0/INT pin, flag bit, INTF
(INTCON<1>), is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). Flag bit INTF
must be cleared in software in the Interrupt Service
Routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if bit INTE
was set prior to going into SLEEP. The status of global
interrupt enable bit GIE decides whether or not the
processor branches to the interrupt vector, following
wake-up. See Section 15.13 “Power-down Mode
(SLEEP)” for details on SLEEP mode.
15.10.2
TMR0 INTERRUPT
An overflow (FFh → 00h) in the TMR0 register will set
flag bit TMR0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit TMR0IE
(INTCON<5>), see Section 6.0 “Timer0 Module”.
EXAMPLE 15-1:
PORTB INTCON CHANGE
An input change on PORTB<7:4> sets flag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>), see
Section 3.2 “EECON1 and EECON2 Registers”.
15.11 Context Saving During Interrupts
During an interrupt, only the return PC value is saved
on the stack. Typically, users may wish to save key registers during an interrupt (i.e., W, STATUS registers).
Since the upper 16 bytes of each bank are common in
the PIC16F87/88 devices, temporary holding registers
W_TEMP, STATUS_TEMP, and PCLATH_TEMP
should be placed in here. These 16 locations don’t
require banking and therefore, make it easier for context save and restore. The same code shown in
Example 15-1 can be used.
SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
MOVWF
SWAPF
CLRF
MOVWF
MOVF
MOVWF
CLRF
:
:(ISR)
:
MOVF
MOVWF
SWAPF
W_TEMP
STATUS,W
STATUS
STATUS_TEMP
PCLATH, W
PCLATH_TEMP
PCLATH
MOVWF
SWAPF
SWAPF
STATUS
W_TEMP,F
W_TEMP,W
;Copy
;Swap
;bank
;Save
;Only
;Save
;Page
W to TEMP register
status to be saved into W
0, regardless of current bank, Clears IRP,RP1,RP0
status to bank zero STATUS_TEMP register
required if using page 1
PCLATH into W
zero, regardless of current page
;(Insert user code here)
PCLATH_TEMP, W
PCLATH
STATUS_TEMP,W
DS30487B-page 140
;Restore PCLATH
;Move W into PCLATH
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
;Swap W_TEMP into W
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.12 Watchdog Timer (WDT)
15.12.2
For PIC16F87/88 devices, the WDT has been modified
from previous PIC16 devices. The new WDT is code
and functionally backward compatible with previous
PIC16 WDT modules, and allows the user to have a
scaler value for the WDT and TMR0 at the same time.
In addition, the WDT time-out value can be extended to
268 seconds, using the prescaler with the postscaler
when PSA is set to ‘1’.
The WDTEN bit is located in Configuration Word 1 and
when this bit is set, the WDT runs continuously.
15.12.1
The PSA and PS<2:0> bits (OPTION_REG) have the
same function as in previous versions of the PIC16
family of microcontrollers.
The SWDTEN bit is in the WDTCON register. When the
WDTEN bit in the Configuration Word 1 register is set,
the SWDTEN bit has no effect. If WDTEN is clear, then
the SWDTEN bit can be used to enable and disable the
WDT. Setting the bit will enable it and clearing the bit
will disable it.
WDT OSCILLATOR
The WDT derives its time base from the 31.25 kHz
INTRC. The value of WDTCON is ‘---0 1000’ on all
RESETS. This gives a nominal time base of 16.38 ms,
which is compatible with the time base generated with
previous PIC16 microcontroller versions.
Note:
WDT CONTROL
When the OST is invoked, the WDT is held
in RESET, because the WDT ripple
counter is used by the OST to perform the
oscillator delay count. When the OST
count has expired, the WDT will begin
counting (if enabled).
A new prescaler has been added to the path between
the internal RC and the multiplexors used to select the
path for the WDT. This prescaler is 16 bits and can be
programmed to divide the internal RC by 128 to 65536,
giving the time base used for the WDT a nominal range
of 1 ms to 2.097s.
FIGURE 15-8:
WATCHDOG TIMER BLOCK DIAGRAM
From TMR0 Clock Source
0
Postscaler
16-bit Programmable Prescaler WDT
1
8
PSA
31.25 kHz
INTRC Clock
PS<2:0>
WDTPS<3:0>
TO TMR0
0
1
PSA
WDTEN from Configuration Word
SWDTEN from WDTCON
WDT Time-out
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 141
PIC16F87/88
TABLE 15-5:
PRESCALER/POSTSCALER BIT STATUS
Conditions
Prescaler
Postscaler (PSA = 1)
Cleared
Cleared
WDTEN = 0
CLRWDT command
Oscillator fail detected
Exit SLEEP + System Clock = T1OSC, EXTRC, INTRC, EXTCLK
Exit SLEEP + System Clock = XT, HS, LP
REGISTER 15-3:
Cleared at end of OST
Cleared at end of OST
WDTCON REGISTER (ADDRESS 105h)
U-0
—
U-0
—
U-0
—
R/W-0
WDTPS3
bit 7
R/W-1
R/W-0
R/W-0
R/W-0
WDTPS2 WDTPS1 WDTPS0 SWDTEN(1)
bit 0
bit 7-5
Unimplemented: Read as ‘0’
bit 4-1
WDTPS<3:0>: Watchdog Timer Period Select bits
Bit
Prescale
Value
Rate
0000 = 1:32
0001 = 1:64
0010 = 1:128
0011 = 1:256
0100 = 1:512
0101 = 1:1024
0110 = 1:2048
0111 = 1:4096
1000 = 1:8192
1001 = 1:16394
1010 = 1:32768
1011 = 1:65536
bit 0
SWDTEN: Software Enable/Disable for Watchdog Timer bit(1)
1 = WDT is turned on
0 = WDT is turned off
Note 1: If WDTEN configuration bit = 1, then WDT is always enabled, irrespective of this control bit. If WDTEN configuration bit = 0, then it is possible to turn WDT on/off with this
control bit.
Legend:
TABLE 15-6:
Address
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
SUMMARY OF WATCHDOG TIMER REGISTERS
Name
81h,181h OPTION
2007h
Configuration bits
105h
WDTCON
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RBPU
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
LVP
BOREN
MVCLRE
FOSC2
PWRTEN
WDTEN
FOSC1
FOSC0
—
—
—
WDTPS3 WDTPS2 WSTPS1 WDTPS0 SWDTEN
Legend: Shaded cells are not used by the Watchdog Timer.
Note 1: See Register 15-1 for operation of these bits.
DS30487B-page 142
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.12.3
TWO-SPEED CLOCK START-UP
MODE
Two-Speed Start-up mode minimizes the latency
between oscillator start-up and code execution that
may be selected with the IESO (Internal/External
Switch Over) bit in Configuration Word 2. This mode is
achieved by initially using the INTRC for code
execution until the primary oscillator is stable.
If this mode is enabled, and any of the following conditions exist, the system will begin execution with the
INTRC oscillator. This results in almost immediate
code execution with a minimum of delay.
• POR and after the Power-up Timer has expired (if
PWRTEN = 0),
• or following a wake-up from SLEEP,
• or a RESET when running from T1OSC or INTRC
(after a RESET, SCS<1:0> are always set to ‘00’).
Note:
Following any RESET, the IRCF bits are
zeroed and the frequency selection is
forced to 31.25 kHz. The user can modify
the IRCF bits to select a higher internal
oscillator frequency.
Checking the state of the OSTS bit will confirm
whether the primary clock configuration is engaged. If
not, the OSTS bit will remain clear.
When the device is auto-configured in INTRC mode following a POR or wake-up from SLEEP, the rules for
entering other oscillator modes still apply, meaning the
SCS<1:0> bits in OSCCON can be modified before the
OST time-out has occurred. This would allow the application to wake-up from SLEEP, perform a few instructions using the INTRC as the clock source and go back
to SLEEP without waiting for the primary oscillator to
become stable.
Note:
15.12.3.1
1.
2.
3.
If the primary oscillator is configured to be anything
other than XT, LP, or HS, then Two-Speed Start-up
mode is disabled, because the primary oscillator will
not require any time to become stable after POR, or an
exit from SLEEP.
4.
5.
6.
7.
If the IRCF bits of the OSCCON register are configured
to a non-zero value prior to entering SLEEP mode, the
system clock frequency will come from the output of
the INTOSC. The IOFS bit in the OSCCON register will
be clear until the INTOSC is stable. This will allow the
user to determine when the internal oscillator can be
used for time critical applications.
8.
FIGURE 15-9:
Executing a SLEEP instruction will abort
the oscillator start-up time and will cause
the OSTS bit to remain clear.
Two-Speed Start-up Mode
Sequence
Wake-up from SLEEP, RESET, or POR.
OSCON bits configured to run from INTRC
(31.25 kHz).
Instructions begin execution by INTRC
(31.25 kHz).
OST enabled to count 1024 clock cycles.
OST timed out, wait for falling edge of INTRC.
OSTS is set.
System clock held low for eight falling edges of
new clock (LP, XT, or HS).
System clock is switched to primary source (LP,
XT, or HS).
The software may read the OSTS bit to determine
when the switch over takes place so that any software
timing edges can be adjusted.
TWO-SPEED START-UP MODE
CPU Start-up
Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1
Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4
INTRC
OSC1
TOST
OSC2
System Clock
SLEEP
OSTS
Program
Counter
PC
 2003 Microchip Technology Inc.
0000h
0001h
Preliminary
0003h
0004h
0005h
DS30487B-page 143
PIC16F87/88
15.12.4
FAIL-SAFE OPTION
The Fail-Safe Clock Monitor (FSCM) is designed to
allow the device to continue to operate even in the
event of an oscillator failure.
FIGURE 15-10:
FSCM BLOCK DIAGRAM
Clock Monitor
Latch (CM)
(edge-triggered)
Peripheral
Clock
S
INTRC
Oscillator
÷ 64
31.25 kHz
(32 µs)
488 Hz
(2.048 ms)
C
Q
Q
Clock
Failure
Detected
The FSCM function is enabled by setting the FCMEN
bit in Configuration Word 2.
In the event of an oscillator failure, the FSCM will generate an oscillator fail interrupt and will switch the system clock over to the internal oscillator. The system
will continue to come from the internal oscillator until
the fail-safe condition is exited. The fail-safe condition
is exited with either a RESET, the execution of a
SLEEP instruction or a write to the OSCCON register.
The frequency of the internal oscillator will depend
upon the value contained in the IRCF bits. Another
clock source can be selected via the IRCF and the
SCS bits of the OSCCON register.
FIGURE 15-11:
The FSCM sample clock is generated by dividing the
INTRC clock by 64. This will allow enough time
between FSCM sample clocks for a system clock edge
to occur.
On the rising edge of the postscaled clock, the monitoring latch (CM = 0) will be cleared. On a falling edge
of the primary or secondary system clock, the monitoring latch will be set (CM = 1). In the event that a falling
edge of the postscaled clock occurs, and the
monitoring latch is not set, a clock failure has been
detected.
While in Fail-Safe mode, a RESET will exit the failsafe condition. If the primary clock source is configured for a crystal, the OST timer will wait for the 1024
clock cycles for the OST time-out, and the device will
continue running from the internal oscillator until the
OST is complete. A SLEEP instruction, or a write to the
SCS bits (where SCS bits do not = 00), can be
performed to put the device into a low-power mode.
Note:
Two-Speed Start-up mode is automatically
enabled when the fail-safe option is
enabled.
If RESET occurs while in Fail-Safe mode and the primary clock source is EC, or RC, then the device will
immediately switch back to EC or RC mode.
15.12.4.1
Fail-Safe in Low-power Mode
A write to the OSCCON register, or SLEEP instruction
will end the fail-safe condition. The system clock will
default to the source selected by the SCS bits, which
is either T1OSC, INTRC, or none (SLEEP mode).
However, the FSCM will continue to monitor the system clock. If the secondary clock fails, the device will
immediately switch to the internal oscillator clock. If
OSFIE is set, an interrupt will be generated.
FSCM TIMING DIAGRAM
Sample Clock
Oscillator
Failure
System
Clock
Output
CM Output
(Q)
Failure
Detected
OSCFIF
CM Test
Note:
CM Test
CM Test
The system clock is normally at a much higher frequency than the sample clock. The relative frequencies in
this example have been chosen for clarity.
DS30487B-page 144
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.12.4.2
FSCM and the Watchdog Timer
2.
After a POR (Power-on Reset), the device is
running in Two-Speed Start-up mode. The crystal fails before the OST has expired. If a crystal
fails during the OST period, a fail-safe condition
will not be detected (OSFIF will not get set).
OSTS = 0
SCS = 00
OSFIF = 0
When a clock failure is detected, SCS<1:0> will be
forced to ‘10’, which will reset the WDT (if enabled).
15.12.4.3
POR or Wake From Sleep
The FSCM is designed to detect oscillator failure at any
point after the device has exited Power-on Reset
(POR) or low-power SLEEP mode. When the primary
system clock is EC, RC or INTRC modes, monitoring
can begin immediately following these events.
For Oscillator modes involving a crystal or resonator
(HS, LP, or XT), the situation is somewhat different.
Since the oscillator may require a start-up time considerably longer than the FSCM sample clock time, a false
clock failure may be detected. To prevent this, the internal oscillator block is automatically configured as the
system clock and functions until the primary clock is
stable (the OST timer has timed out). This is identical
to Two-Speed Start-up mode. Once the primary clock is
stable, the INTRC returns to its role as the FSCM
source.
Note:
15.12.4.4
1.
USER ACTION:
Check the OSTS bit. If it’s clear and the OST
should have expired at this point, then the user
can assume the crystal has failed. The user
should change the SCS bit to cause a clock
switch which will also release the 10-bit ripple
counter for WDT operation (if enabled).
3.
CONDITIONS:
The device is clocked from a crystal during
normal operation and it fails.
OSTS = 0
SCS = 00
OSFIF = 1
The same logic that prevents false oscillator failure interrupts on PORT or wake
from SLEEP, will also prevent the detection of the oscillator’s failure to start at all
following these events. This can be
avoided by monitoring the OSTS bit and
using a timing routine to determine if the
oscillator is taking too long to start. Even
so, no oscillator failure interrupt will be
flagged.
Example Fail-Safe Conditions
CONDITIONS:
USER ACTION:
Clear the OSFIF bit. Configure the SCS bits for
a clock switch and the fail-safe condition will be
cleared. Later, if the user decides to, the crystal
can be re-tried for operation. If this is done, the
OSTS bit should be monitored to determine if
the crystal operates.
15.13 Power-down Mode (SLEEP)
CONDITIONS:
The device is clocked from a crystal, crystal
operation fails and then SLEEP mode is
entered.
OSTS = 0
SCS = 00
OSFIF = 1
USER ACTION:
SLEEP mode will exit the fail-safe condition.
Therefore, if the user code did not handle the
detected fail-safe prior to the SLEEP command,
then upon wake-up, the device will try to start
the crystal that failed and a fail-safe condition
will not be detected. Monitoring the OSTS bit will
determine if the crystal is operating. The user
should not enter SLEEP mode without handling
the fail-safe condition first.
Power-down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the PD bit (STATUS<3>) is cleared, the
TO (STATUS<4>) bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, low, or high-impedance).
For lowest current consumption in this mode, place all
I/O pins at either VDD or VSS, ensure no external circuitry is drawing current from the I/O pin, power-down
the A/D and disable external clocks. Pull all I/O pins
that are hi-impedance inputs, high or low externally, to
avoid switching currents caused by floating inputs. The
T0CKI input should also be at VDD or VSS for lowest
current consumption. The contribution from on-chip
pull-ups on PORTB should also be considered.
The MCLR pin must be at a logic high level (VIHMC).
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 145
PIC16F87/88
15.13.1
WAKE-UP FROM SLEEP
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
External RESET input on MCLR pin.
Watchdog Timer wake-up (if WDT was enabled).
Interrupt from INT pin, RB port change or a
peripheral interrupt.
External MCLR Reset will cause a device RESET. All
other events are considered a continuation of program
execution and cause a “wake-up”. The TO and PD bits
in the STATUS register can be used to determine the
cause of the device RESET. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared if a WDT time-out occurred and caused
wake-up.
The following peripheral interrupts can wake the device
from SLEEP:
1.
2.
3.
4.
5.
6.
7.
8.
9.
TMR1 interrupt. Timer1 must be operating as an
asynchronous counter.
CCP Capture mode interrupt.
Special event trigger (Timer1 in Asynchronous
mode using an external clock).
SSP (START/STOP) bit detect interrupt.
SSP transmit or receive in Slave mode (SPI/I2C).
A/D conversion (when A/D clock source is RC).
EEPROM write operation completion.
Comparator output changes state.
USART RX or TX (Synchronous Slave mode).
Other peripherals cannot generate interrupts, since
during SLEEP, no on-chip clocks are present.
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up
occurs regardless of the state of the GIE bit. If the GIE
bit is clear (disabled), the device continues execution at
the instruction after the SLEEP instruction. If the GIE bit
is set (enabled), the device executes the instruction
after the SLEEP instruction and then branches to the
interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable,
the user should have a NOP after the SLEEP instruction.
15.13.2
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the execution of a
SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT
prescaler and postscaler (if enabled) will not be
cleared, the TO bit will not be set and the PD bit
will not be cleared.
• If the interrupt occurs during or after the
execution of a SLEEP instruction, the device will
immediately wake-up from SLEEP. The SLEEP
instruction will be completely executed before the
wake-up. Therefore, the WDT and WDT prescaler
and postscaler (if enabled) will be cleared, the TO
bit will be set and the PD bit will be cleared.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
To ensure that the WDT is cleared, a CLRWDT instruction
should be executed before a SLEEP instruction.
WAKE-UP FROM SLEEP THROUGH INTERRUPT(1)
FIGURE 15-12:
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
TOST(2)
CLKO(4)
INT pin
INTF Flag
(INTCON<1>)
Interrupt Latency
(Note 2)
bit(3)
GIE
(INTCON<7>)
Processor in
SLEEP
INSTRUCTION FLOW
PC
Instruction
Fetched
Instruction
Executed
Note
1:
2:
3:
4:
PC
PC+1
PC+2
PC+2
Inst(PC) = SLEEP
Inst(PC + 1)
Inst(PC + 2)
Inst(PC - 1)
SLEEP
Inst(PC + 1)
PC + 2
Dummy Cycle
0004h
0005h
Inst(0004h)
Inst(0005h)
Dummy Cycle
Inst(0004h)
XT, HS or LP Oscillator mode assumed.
TOST = 1024 TOSC (drawing not to scale). This delay will not be there for RC Osc mode.
GIE = 1 assumed. In this case, after wake-up, the processor jumps to the interrupt routine.
If GIE = 0, execution will continue in-line.
CLKO is not available in these Osc modes, but shown here for timing reference.
DS30487B-page 146
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
15.14 In-Circuit Debugger
15.17 In-Circuit Serial Programming
When the DEBUG bit in the configuration word is programmed to a ‘0’, the In-Circuit Debugger functionality
is enabled. This function allows simple debugging functions when used with MPLAB® ICD. When the microcontroller has this feature enabled, some of the
resources are not available for general use. Table 15-7
shows which features are consumed by the background
debugger.
PIC16F87/88 microcontrollers can be serially programmed while in the end application circuit. This is
simply done with two lines for clock and data and three
other lines for power, ground, and the programming
voltage (see Figure 15-13 for an example). This allows
customers to manufacture boards with unprogrammed
devices and then program the microcontroller just
before shipping the product. This also allows the most
recent firmware or a custom firmware to be
programmed.
TABLE 15-7:
DEBUGGER RESOURCES
I/O pins
RB6, RB7
Stack
Program Memory
1 level
Address 0000h must be NOP
Last 100h words
Data Memory
For more information on serial programming, please
refer to the PIC16F87/88 Programming Specification
(DS39607).
FIGURE 15-13:
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
0x070 (0x0F0, 0x170, 0x1F0)
0x1EB-0x1EF
To use the In-Circuit Debugger function of the microcontroller, the design must implement In-Circuit Serial
Programming connections to MCLR/VPP, VDD, GND,
RB7 and RB6. This will interface to the In-Circuit
Debugger module available from Microchip, or one of
the third party development tool companies.
To Normal
Connections
External
Connector
Signals
15.15 Program Verification/Code
Protection
If the code protection bit(s) have not been programmed, the on-chip program memory can be read
out for verification purposes.
*
PIC16F87/88
+5V
VDD
0V
VSS
VPP
MCLR/VPP
CLK
RB6
Data I/O
RB7
RB3†
RB3/PGM
15.16 ID Locations
Four memory locations (2000h - 2003h) are designated
as ID locations, where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution, but are readable and writable during program/verify. It is recommended that only the four Least Significant bits of the
ID location are used.
 2003 Microchip Technology Inc.
*
*
*
VDD
To Normal
Connections
* Isolation devices (as required).
†
RB3 only used in LVP mode.
Preliminary
DS30487B-page 147
PIC16F87/88
15.18 Low-Voltage ICSP Programming
The LVP bit of the configuration word enables lowvoltage ICSP programming. This mode allows the
microcontroller to be programmed via ICSP using a
VDD source in the operating voltage range. This only
means that VPP does not have to be brought to VIHH,
but can instead be left at the normal operating voltage.
In this mode, the RB3/PGM pin is dedicated to the programming function and ceases to be a general purpose
I/O pin.
Note 1: The High-Voltage Programming mode is
always available, regardless of the state
of the LVP bit, by applying VIHH to the
MCLR pin.
If Low-Voltage Programming mode is not used, the LVP
bit can be programmed to a ‘0’ and RB3/PGM becomes
a digital I/O pin. However, the LVP bit may only be programmed when programming mode is entered with
VIHH on MCLR. The LVP bit can only be changed when
using high voltage on MCLR.
It should be noted that once the LVP bit is programmed
to ‘0’, only the High-Voltage Programming mode is
available and only this mode can be used to program
the device.
When using Low-Voltage ICSP, the part must be supplied at 4.5V to 5.5V if a bulk erase will be executed. This
includes reprogramming of the code protect bits from an
on-state to an off-state. For all other cases of LowVoltage ICSP, the part may be programmed at the normal operating voltage. This means calibration values,
unique user IDs, or user code can be reprogrammed or
added.
2: While in Low-Voltage ICSP mode
(LVP = 1), the RB3 pin can no longer be
used as a general purpose I/O pin.
3: When using Low-Voltage ICSP Programming (LVP) and the pull-ups on PORTB
are enabled, bit 3 in the TRISB register
must be cleared to disable the pull-up on
RB3 and ensure the proper operation of
the device.
4: RB3 should not be allowed to float if LVP
is enabled. An external pull-down device
should be used to default the device to
normal operating mode. If RB3 floats
high, the PIC16F87/88 device will enter
Programming mode.
5: LVP mode is enabled by default on all
devices shipped from Microchip. It can be
disabled by clearing the LVP bit in the
CONFIG register.
6: Disabling LVP will provide maximum
compatibility to other PIC16CXXX
devices.
The following LVP steps assume the LVP bit is set in the
Configuration register.
1.
2.
3.
4.
5.
Apply VDD to the VDD pin.
Drive MCLR low.
Apply VDD to the RB3/PGM pin.
Apply VDD to the MCLR pin.
Follow with the associated programming steps.
DS30487B-page 148
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
16.0
INSTRUCTION SET SUMMARY
The PIC16 instruction set is highly orthogonal and is
comprised of three basic categories:
• Byte-oriented operations
• Bit-oriented operations
For example, a “clrf PORTB” instruction will read
PORTB, clear all the data bits, then write the result
back to PORTB. This example would have the unintended result that the condition that sets the RBIF flag
would be cleared.
TABLE 16-1:
• Literal and control operations
Each PIC16 instruction is a 14-bit word divided into an
opcode, which specifies the instruction type, and one
or more operands, which further specify the operation
of the instruction. The formats for each of the categories are presented in Figure 16-1, while the various
opcode fields are summarized in Table 16-1.
Table 16-2 lists the instructions recognized by the
MPASMTM assembler. A complete description of each
instruction is also available in the PICmicro® Mid-Range
MCU Family Reference Manual (DS33023).
For byte-oriented instructions, ‘f’ represents a file register designator and ‘d’ represents a destination designator. The file register designator specifies which file
register is to be used by the instruction.
The destination designator specifies where the result of
the operation is to be placed. If ‘d’ is zero, the result is
placed in the W register. If ‘d’ is one, the result is placed
in the file register specified in the instruction.
For bit-oriented instructions, ‘b’ represents a bit field
designator, which selects the bit affected by the operation, while ‘f’ represents the address of the file in which
the bit is located.
Field
Description
f
Register file address (0x00 to 0x7F)
W
Working register (accumulator)
b
Bit address within an 8-bit file register
k
Literal field, constant data or label
x
Don't care location (= 0 or 1).
The assembler will generate code with x = 0.
It is the recommended form of use for
compatibility with all Microchip software tools.
d
Destination select; d = 0: store result in W,
d = 1: store result in file register f.
Default is d = 1.
PC
Program Counter
TO
Time-out bit
PD
Power-down bit
FIGURE 16-1:
For literal and control operations, ‘k’ represents an
eight or eleven-bit constant or literal value
One instruction cycle consists of four oscillator periods;
for an oscillator frequency of 4 MHz, this gives a normal
instruction execution time of 1 µs. All instructions are
executed within a single instruction cycle, unless a conditional test is true, or the program counter is changed
as a result of an instruction. When this occurs, the execution takes two instruction cycles, with the second
cycle executed as a NOP.
Note:
OPCODE FIELD
DESCRIPTIONS
To maintain upward compatibility with
future PIC16F87/88 products, do not use
the OPTION and TRIS instructions.
All instruction examples use the format ‘0xhh’ to represent a hexadecimal number, where ‘h’ signifies a
hexadecimal digit.
GENERAL FORMAT FOR
INSTRUCTIONS
Byte-oriented file register operations
13
8 7 6
OPCODE
d
f (FILE #)
0
d = 0 for destination W
d = 1 for destination f
f = 7-bit file register address
Bit-oriented file register operations
13
10 9
7 6
OPCODE
b (BIT #)
f (FILE #)
0
b = 3-bit bit address
f = 7-bit file register address
Literal and control operations
General
13
8
7
OPCODE
0
k (literal)
k = 8-bit immediate value
16.1
READ-MODIFY-WRITE
OPERATIONS
CALL and GOTO instructions only
Any instruction that specifies a file register as part of
the instruction performs a Read-Modify-Write (R-M-W)
operation. The register is read, the data is modified,
and the result is stored according to either the instruction, or the destination designator ‘d’. A read operation
is performed on a register even if the instruction writes
to that register.
 2003 Microchip Technology Inc.
Preliminary
13
11
OPCODE
10
0
k (literal)
k = 11-bit immediate value
DS30487B-page 149
PIC16F87/88
TABLE 16-2:
PIC16F87/88 INSTRUCTION SET
Mnemonic,
Operands
Description
Cycles
14-Bit Opcode
MSb
LSb
Status
Affected
Notes
BYTE-ORIENTED FILE REGISTER OPERATIONS
ADDWF
ANDWF
CLRF
CLRW
COMF
DECF
DECFSZ
INCF
INCFSZ
IORWF
MOVF
MOVWF
NOP
RLF
RRF
SUBWF
SWAPF
XORWF
f, d
f, d
f
f, d
f, d
f, d
f, d
f, d
f, d
f, d
f
f, d
f, d
f, d
f, d
f, d
Add W and f
AND W with f
Clear f
Clear W
Complement f
Decrement f
Decrement f, Skip if 0
Increment f
Increment f, Skip if 0
Inclusive OR W with f
Move f
Move W to f
No Operation
Rotate Left f through Carry
Rotate Right f through Carry
Subtract W from f
Swap nibbles in f
Exclusive OR W with f
1
1
1
1
1
1
1(2)
1
1(2)
1
1
1
1
1
1
1
1
1
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
0111
0101
0001
0001
1001
0011
1011
1010
1111
0100
1000
0000
0000
1101
1100
0010
1110
0110
dfff
dfff
lfff
0xxx
dfff
dfff
dfff
dfff
dfff
dfff
dfff
lfff
0xx0
dfff
dfff
dfff
dfff
dfff
ffff
ffff
ffff
xxxx
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
0000
ffff
ffff
ffff
ffff
ffff
00bb
01bb
10bb
11bb
bfff
bfff
bfff
bfff
ffff
ffff
ffff
ffff
111x
1001
0kkk
0000
1kkk
1000
00xx
0000
01xx
0000
0000
110x
1010
kkkk
kkkk
kkkk
0110
kkkk
kkkk
kkkk
0000
kkkk
0000
0110
kkkk
kkkk
kkkk
kkkk
kkkk
0100
kkkk
kkkk
kkkk
1001
kkkk
1000
0011
kkkk
kkkk
C,DC,Z
Z
Z
Z
Z
Z
Z
Z
Z
C
C
C,DC,Z
Z
1,2
1,2
2
1,2
1,2
1,2,3
1,2
1,2,3
1,2
1,2
1,2
1,2
1,2
1,2
1,2
BIT-ORIENTED FILE REGISTER OPERATIONS
BCF
BSF
BTFSC
BTFSS
f, b
f, b
f, b
f, b
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
1
1
1 (2)
1 (2)
ADDLW
ANDLW
CALL
CLRWDT
GOTO
IORLW
MOVLW
RETFIE
RETLW
RETURN
SLEEP
SUBLW
XORLW
k
k
k
k
k
k
k
k
k
Add literal and W
AND literal with W
Call subroutine
Clear Watchdog Timer
Go to address
Inclusive OR literal with W
Move literal to W
Return from interrupt
Return with literal in W
Return from Subroutine
Go into Standby mode
Subtract W from literal
Exclusive OR literal with W
01
01
01
01
1,2
1,2
3
3
LITERAL AND CONTROL OPERATIONS
Note 1:
2:
3:
Note:
1
1
2
1
2
1
1
2
2
2
1
1
1
11
11
10
00
10
11
11
00
11
00
00
11
11
C,DC,Z
Z
TO,PD
Z
TO,PD
C,DC,Z
Z
When an I/O register is modified as a function of itself (e.g., MOVF PORTB, 1), the value used will be that value present
on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is driven low by an external
device, the data will be written back with a ‘0’.
If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if
assigned to the Timer0 module.
If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is
executed as a NOP.
Additional information on the mid-range instruction set is available in the PICmicro® Mid-Range MCU
Family Reference Manual (DS33023).
DS30487B-page 150
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
16.2
Instruction Descriptions
ADDLW
Add Literal and W
ANDWF
AND W with f
Syntax:
[ label ] ADDLW
Syntax:
[ label ] ANDWF
Operands:
0 ≤ k ≤ 255
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(W) + k → (W)
Status Affected:
C, DC, Z
Operation:
(W) .AND. (f) → (destination)
The contents of the W register
are added to the eight-bit literal ‘k’
and the result is placed in the W
register.
Status Affected:
Z
Description:
AND the W register with register
‘f’. If ‘d’ = 0, the result is stored in
the W register. If ‘d’ = 1, the result
is stored back in register ‘f’.
ADDWF
Add W and f
BCF
Bit Clear f
Syntax:
[ label ] ADDWF
Syntax:
[ label ] BCF
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
0≤b≤7
Operation:
(W) + (f) → (destination)
Operation:
0 → (f<b>)
Status Affected:
C, DC, Z
Status Affected:
None
Description:
Add the contents of the W register
with register ‘f’. If ‘d’ = 0, the result
is stored in the W register. If
‘d’ = 1, the result is stored back in
register ‘f’.
Description:
Bit ‘b’ in register ‘f’ is cleared.
ANDLW
AND Literal with W
BSF
Bit Set f
Syntax:
[ label ] ANDLW
Syntax:
[ label ] BSF
Operands:
0 ≤ f ≤ 127
0≤b≤7
Description:
k
f,d
k
f,d
f,b
f,b
Operands:
0 ≤ k ≤ 255
Operation:
(W) .AND. (k) → (W)
Status Affected:
Z
Operation:
1 → (f<b>)
Description:
The contents of W register are
AND’ed with the eight-bit literal
‘k’. The result is placed in the W
register.
Status Affected:
None
Description:
Bit ‘b’ in register ‘f’ is set.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 151
PIC16F87/88
BTFSS
Bit Test f, Skip if Set
CLRF
Clear f
Syntax:
[ label ] BTFSS f,b
Syntax:
[ label ] CLRF
Operands:
0 ≤ f ≤ 127
0≤b<7
Operands:
0 ≤ f ≤ 127
Operation:
Operation:
skip if (f<b>) = 1
00h → (f)
1→Z
Status Affected:
None
Status Affected:
Z
Description:
If bit ‘b’ in register ‘f’ = 0, the next
instruction is executed.
If bit ‘b’ = 1, then the next
instruction is discarded and a NOP
is executed instead, making this a
2 TCY instruction.
Description:
The contents of register ‘f’ are
cleared and the Z bit is set.
BTFSC
Bit Test, Skip if Clear
CLRW
Clear W
Syntax:
[ label ] BTFSC f,b
Syntax:
[ label ] CLRW
Operands:
0 ≤ f ≤ 127
0≤b≤7
Operands:
None
Operation:
Operation:
skip if (f<b>) = 0
00h → (W)
1→Z
Status Affected:
None
Status Affected:
Z
Description:
If bit ‘b’ in register ‘f’ = 1, the next
instruction is executed.
If bit ‘b’, in register ‘f’, = 0, the next
instruction is discarded, and a NOP
is executed instead, making this a
2 TCY instruction.
Description:
W register is cleared. Zero bit (Z)
is set.
CALL
Call Subroutine
CLRWDT
Clear Watchdog Timer
Syntax:
[ label ] CALL k
Syntax:
[ label ] CLRWDT
Operands:
0 ≤ k ≤ 2047
Operands:
None
Operation:
(PC) + 1 → TOS,
k → PC<10:0>,
(PCLATH<4:3>) → PC<12:11>
Operation:
Status Affected:
None
00h → WDT
0 → WDT prescaler,
1 → TO
1 → PD
Description:
Call subroutine. First, return
address (PC+1) is pushed onto
the stack. The eleven-bit immediate address is loaded into PC bits
<10:0>. The upper bits of the PC
are loaded from PCLATH. CALL is
a two-cycle instruction.
Status Affected:
TO, PD
Description:
CLRWDT instruction resets the
Watchdog Timer. It also resets the
prescaler of the WDT. Status bits
TO and PD are set.
DS30487B-page 152
Preliminary
f
 2003 Microchip Technology Inc.
PIC16F87/88
COMF
Complement f
Syntax:
[ label ] COMF
GOTO
Unconditional Branch
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ k ≤ 2047
Operation:
(f) → (destination)
Operation:
k → PC<10:0>
PCLATH<4:3> → PC<12:11>
Status Affected:
Z
Status Affected:
None
Description:
The contents of register ‘f’ are
complemented. If ‘d’ = 0, the
result is stored in W. If ‘d’ = 1, the
result is stored back in register ‘f’.
Description:
GOTO is an unconditional branch.
The eleven-bit immediate value is
loaded into PC bits <10:0>. The
upper bits of PC are loaded
from PCLATH<4:3>. GOTO is a
two-cycle instruction.
DECF
Decrement f
INCF
Increment f
Syntax:
[ label ] DECF f,d
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) - 1 → (destination)
Operation:
(f) + 1 → (destination)
Status Affected:
Z
Status Affected:
Z
Description:
Decrement register ‘f’. If ‘d’ = 0,
the result is stored in the W
register. If ‘d’ = 1, the result is
stored back in register ‘f’.
Description:
The contents of register ‘f’ are
incremented. If ‘d’ = 0, the result
is placed in the W register. If
‘d’ = 1, the result is placed back in
register ‘f’.
DECFSZ
Decrement f, Skip if 0
INCFSZ
Increment f, Skip if 0
Syntax:
[ label ] DECFSZ f,d
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) - 1 → (destination);
skip if result = 0
Operation:
(f) + 1 → (destination),
skip if result = 0
Status Affected:
None
Status Affected:
None
Description:
The contents of register ‘f’ are
decremented. If ‘d’ = 0, the result
is placed in the W register. If
‘d’ = 1, the result is placed back in
register ‘f’.
If the result is ‘1’, the next
instruction is executed. If the
result is ‘0’, then a NOP is
executed instead, making it a
2 TCY instruction.
Description:
The contents of register ‘f’ are
incremented. If ‘d’ = 0, the result is
placed in the W register. If ‘d’ = 1,
the result is placed back in
register ‘f’.
If the result is ‘1’, the next
instruction is executed. If the
result is ‘0’, a NOP is executed
instead, making it a 2 TCY
instruction.
 2003 Microchip Technology Inc.
f,d
Preliminary
GOTO k
INCF f,d
INCFSZ f,d
DS30487B-page 153
PIC16F87/88
IORLW
Inclusive OR Literal with W
MOVLW
Move Literal to W
Syntax:
[ label ]
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 255
Operands:
0 ≤ k ≤ 255
Operation:
(W) .OR. k → (W)
Operation:
k → (W)
Status Affected:
Z
Status Affected:
None
Description:
The contents of the W register are
OR’d with the eight-bit literal ‘k’.
The result is placed in the W
register.
Description:
The eight-bit literal ‘k’ is loaded
into W register. The don’t cares
will assemble as ‘0’s.
IORWF
Inclusive OR W with f
MOVWF
Move W to f
Syntax:
[ label ]
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
Operation:
(W) .OR. (f) → (destination)
(W) → (f)
Operation:
Status Affected:
None
Status Affected:
Z
Description:
Description:
Inclusive OR the W register with
register ‘f’. If ‘d’ = 0, the result is
placed in the W register. If ‘d’ = 1,
the result is placed back in
register ‘f’.
Move data from W register to
register ‘f’.
MOVF
Move f
NOP
No Operation
IORLW k
IORWF
f,d
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) → (destination)
Status Affected:
Z
Description:
The contents of register ‘f’ are
moved to a destination dependant
upon the status of ‘d’. If ‘d’ = 0,
the destination is W register. If
‘d’ = 1, the destination is file
register ‘f’ itself. ‘d’ = 1 is useful to
test a file register, since status
flag Z is affected.
DS30487B-page 154
MOVF f,d
MOVLW k
MOVWF
Syntax:
[ label ]
Operands:
None
Operation:
No operation
Status Affected:
None
Description:
No operation.
Preliminary
f
NOP
 2003 Microchip Technology Inc.
PIC16F87/88
RETFIE
Return from Interrupt
RLF
Rotate Left f through Carry
Syntax:
[ label ]
Syntax:
[ label ]
Operands:
None
Operands:
Operation:
TOS → PC,
1 → GIE
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
See description below
Status Affected:
None
Status Affected:
C
Description:
The contents of register ‘f’ are
rotated one bit to the left through
the Carry Flag. If ‘d’ = 0, the
result is placed in the W register.
If ‘d’ = 1, the result is stored back
in register ‘f’.
RETFIE
RLF
C
f,d
Register f
RETLW
Return with Literal in W
RRF
Rotate Right f through Carry
Syntax:
[ label ]
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 255
Operands:
Operation:
k → (W);
TOS → PC
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
See description below
Status Affected:
None
Status Affected:
C
Description:
The W register is loaded with the
eight-bit literal ‘k’. The program
counter is loaded from the top of
the stack (the return address).
This is a two-cycle instruction.
Description:
The contents of register ‘f’ are
rotated one bit to the right through
the Carry Flag. If ‘d’ = 0, the result
is placed in the W register. If
‘d’ = 1, the result is placed back in
register ‘f’.
RETLW k
RRF f,d
C
Register f
RETURN
Return from Subroutine
SLEEP
Syntax:
[ label ]
Syntax:
Operands:
None
Operands:
None
Operation:
TOS → PC
Operation:
00h → WDT,
0 → WDT prescaler,
1 → TO,
0 → PD
Status Affected:
TO, PD
Description:
The power-down status bit, PD is
cleared. Time-out status bit, TO
is set. Watchdog Timer and its
prescaler are cleared.
The processor is put into SLEEP
mode with the oscillator stopped.
RETURN
Status Affected:
None
Description:
Return from subroutine. The stack
is POPed and the top of the stack
(TOS) is loaded into the program
counter. This is a two-cycle
instruction.
 2003 Microchip Technology Inc.
Preliminary
[ label ]
SLEEP
DS30487B-page 155
PIC16F87/88
SUBLW
Syntax:
Subtract W from Literal
[ label ]
SUBLW k
XORLW
Exclusive OR Literal with W
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 255
Operands:
0 ≤ k ≤ 255
Operation:
k - (W) → (W)
XORLW k
Operation:
(W) .XOR. k → (W)
Status Affected: C, DC, Z
Status Affected:
Z
Description:
The W register is subtracted (2’s
complement method) from the
eight-bit literal ‘k’. The result is
placed in the W register.
Description:
The contents of the W register
are XOR’ed with the eight-bit
literal ‘k’. The result is placed in
the W register.
SUBWF
Syntax:
Subtract W from f
[ label ]
SUBWF f,d
XORWF
Syntax:
[ label ] XORWF
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) - (W) → (destination)
Operation:
(W) .XOR. (f) → (destination)
Status Affected: C, DC, Z
Status Affected:
Z
Description:
Description:
Exclusive OR the contents of the
W register with register ‘f’. If
‘d’ = 0, the result is stored in the
W register. If ‘d’ = 1, the result is
stored back in register ‘f’.
Subtract (2’s complement method)
W register from register ‘f’. If
‘d’ = 0, the result is stored in the W
register. If ‘d’ = 1, the result is
stored back in register ‘f’.
SWAPF
Swap Nibbles in f
Syntax:
[ label ] SWAPF f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f<3:0>) → (destination<7:4>),
(f<7:4>) → (destination<3:0>)
Status Affected:
None
Description:
The upper and lower nibbles of
register ‘f’ are exchanged. If
‘d’ = 0, the result is placed in W
register. If ‘d’ = 1, the result is
placed in register ‘f’.
DS30487B-page 156
Preliminary
Exclusive OR W with f
f,d
 2003 Microchip Technology Inc.
PIC16F87/88
17.0
DEVELOPMENT SUPPORT
17.1
The PICmicro® microcontrollers are supported with a
full range of hardware and software development tools:
• Integrated Development Environment
- MPLAB® IDE Software
• Assemblers/Compilers/Linkers
- MPASMTM Assembler
- MPLAB C17 and MPLAB C18 C Compilers
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB C30 C Compiler
- MPLAB ASM30 Assembler/Linker/Library
• Simulators
- MPLAB SIM Software Simulator
- MPLAB dsPIC30 Software Simulator
• Emulators
- MPLAB ICE 2000 In-Circuit Emulator
- MPLAB ICE 4000 In-Circuit Emulator
• In-Circuit Debugger
- MPLAB ICD 2
• Device Programmers
- PRO MATE® II Universal Device Programmer
- PICSTART® Plus Development Programmer
• Low-cost Demonstration Boards
- PICDEMTM 1 Demonstration Board
- PICDEM.netTM Demonstration Board
- PICDEM 2 Plus Demonstration Board
- PICDEM 3 Demonstration Board
- PICDEM 4 Demonstration Board
- PICDEM 17 Demonstration Board
- PICDEM 18R Demonstration Board
- PICDEM LIN Demonstration Board
- PICDEM USB Demonstration Board
• Evaluation Kits
- KEELOQ®
- PICDEM MSC
- microID®
- CAN
- PowerSmart®
- Analog
MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows®
based application that contains:
• An interface to debugging tools
- simulator
- programmer (sold separately)
- emulator (sold separately)
- in-circuit debugger (sold separately)
• A full-featured editor with color coded context
• A multiple project manager
• Customizable data windows with direct edit of
contents
• High level source code debugging
• Mouse over variable inspection
• Extensive on-line help
The MPLAB IDE allows you to:
• Edit your source files (either assembly or C)
• One touch assemble (or compile) and download
to PICmicro emulator and simulator tools
(automatically updates all project information)
• Debug using:
- source files (assembly or C)
- absolute listing file (mixed assembly and C)
- machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increasing flexibility
and power.
17.2
MPASM Assembler
The MPASM assembler is a full-featured, universal
macro assembler for all PICmicro MCUs.
The MPASM assembler generates relocatable object
files for the MPLINK object linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and
generated machine code and COFF files for
debugging.
The MPASM assembler features include:
• Integration into MPLAB IDE projects
• User defined macros to streamline assembly code
• Conditional assembly for multi-purpose source
files
• Directives that allow complete control over the
assembly process
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page157
PIC16F87/88
17.3
MPLAB C17 and MPLAB C18
C Compilers
17.6
The MPLAB C17 and MPLAB C18 Code Development
Systems are complete ANSI C compilers for
Microchip’s PIC17CXXX and PIC18CXXX family of
microcontrollers. These compilers provide powerful
integration capabilities, superior code optimization and
ease of use not found with other compilers.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
17.4
MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK object linker combines relocatable
objects created by the MPASM assembler and the
MPLAB C17 and MPLAB C18 C compilers. It can link
relocatable objects from pre-compiled libraries, using
directives from a linker script.
The MPLIB object librarian manages the creation and
modification of library files of pre-compiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
17.5
MPLAB C30 C Compiler
MPLAB C30 is distributed with a complete ANSI C
standard library. All library functions have been validated and conform to the ANSI C library standard. The
library includes functions for string manipulation,
dynamic memory allocation, data conversion, timekeeping, and math functions (trigonometric, exponential and hyperbolic). The compiler provides symbolic
information for high level source debugging with the
MPLAB IDE.
DS30487B-page 158
MPLAB ASM30 assembler produces relocatable
machine code from symbolic assembly language for
dsPIC30F devices. MPLAB C30 compiler uses the
assembler to produce it’s object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
•
•
•
•
•
•
Support for the entire dsPIC30F instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
17.7
MPLAB SIM Software Simulator
The MPLAB SIM software simulator allows code development in a PC hosted environment by simulating the
PICmicro series microcontrollers on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a file, or user defined key press, to any pin. The execution can be performed in Single-Step, Execute Until
Break, or Trace mode.
The MPLAB SIM simulator fully supports symbolic
debugging using the MPLAB C17 and MPLAB C18
C Compilers, as well as the MPASM assembler. The
software simulator offers the flexibility to develop and
debug code outside of the laboratory environment,
making it an excellent, economical software
development tool.
17.8
The MPLAB C30 C compiler is a full-featured, ANSI
compliant, optimizing compiler that translates standard
ANSI C programs into dsPIC30F assembly language
source. The compiler also supports many commandline options and language extensions to take full
advantage of the dsPIC30F device hardware capabilities, and afford fine control of the compiler code
generator.
MPLAB ASM30 Assembler, Linker,
and Librarian
MPLAB SIM30 Software Simulator
The MPLAB SIM30 software simulator allows code
development in a PC hosted environment by simulating
the dsPIC30F series microcontrollers on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a file, or user defined key press, to any of the pins.
The MPLAB SIM30 simulator fully supports symbolic
debugging using the MPLAB C30 C Compiler and
MPLAB ASM30 assembler. The simulator runs in either
a Command Line mode for automated tasks, or from
MPLAB IDE. This high-speed simulator is designed to
debug, analyze and optimize time intensive DSP
routines.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
17.9
MPLAB ICE 2000
High-performance Universal
In-Circuit Emulator
17.11 MPLAB ICD 2 In-Circuit Debugger
The MPLAB ICE 2000 universal in-circuit emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for
PICmicro microcontrollers. Software control of the
MPLAB ICE 2000 in-circuit emulator is advanced by
the MPLAB Integrated Development Environment,
which allows editing, building, downloading and source
debugging from a single environment.
The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring
features. Interchangeable processor modules allow the
system to be easily reconfigured for emulation of different processors. The universal architecture of the
MPLAB ICE in-circuit emulator allows expansion to
support new PICmicro microcontrollers.
The MPLAB ICE 2000 in-circuit emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft® Windows 32-bit operating system were
chosen to best make these features available in a
simple, unified application.
17.10 MPLAB ICE 4000
High-performance Universal
In-Circuit Emulator
The MPLAB ICE 4000 universal in-circuit emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for highend PICmicro microcontrollers. Software control of the
MPLAB ICE in-circuit emulator is provided by the
MPLAB Integrated Development Environment, which
allows editing, building, downloading and source
debugging from a single environment.
The MPLAB ICD 4000 is a premium emulator system,
providing the features of MPLAB ICE 2000, but with
increased emulation memory and high-speed performance for dsPIC30F and PIC18XXXX devices. Its
advanced emulator features include complex triggering
and timing, up to 2 Mb of emulation memory, and the
ability to view variables in real time.
Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a
powerful, low-cost, run-time development tool,
connecting to the host PC via an RS-232 or high-speed
USB interface. This tool is based on the FLASH
PICmicro MCUs and can be used to develop for these
and other PICmicro microcontrollers. The MPLAB
ICD 2 utilizes the in-circuit debugging capability built
into the FLASH devices. This feature, along with
Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM)
protocol, offers cost effective in-circuit FLASH debugging from the graphical user interface of the MPLAB
Integrated Development Environment. This enables a
designer to develop and debug source code by setting
breakpoints, single-stepping and watching variables,
CPU status and peripheral registers. Running at full
speed enables testing hardware and applications in
real time. MPLAB ICD 2 also serves as a development
programmer for selected PICmicro devices.
17.12 PRO MATE II Universal Device
Programmer
The PRO MATE II is a universal, CE compliant device
programmer with programmable voltage verification at
VDDMIN and VDDMAX for maximum reliability. It features
an LCD display for instructions and error messages
and a modular detachable socket assembly to support
various package types. In Stand-Alone mode, the
PRO MATE II device programmer can read, verify, and
program PICmicro devices without a PC connection. It
can also set code protection in this mode.
17.13 PICSTART Plus Development
Programmer
The PICSTART Plus development programmer is an
easy-to-use, low-cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB
Integrated Development Environment software makes
using the programmer simple and efficient. The
PICSTART Plus development programmer supports
most PICmicro devices up to 40 pins. Larger pin count
devices, such as the PIC16C92X and PIC17C76X,
may be supported with an adapter socket. The
PICSTART Plus development programmer is CE
compliant.
The MPLAB ICE 4000 in-circuit emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft Windows 32-bit operating system were chosen to best make these features available in a simple,
unified application.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page159
PIC16F87/88
17.14 PICDEM 1 PICmicro
Demonstration Board
17.17 PICDEM 3 PIC16C92X
Demonstration Board
The PICDEM 1 demonstration board demonstrates the
capabilities of the PIC16C5X (PIC16C54 to
PIC16C58A), PIC16C61, PIC16C62X, PIC16C71,
PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All
necessary hardware and software is included to run
basic demo programs. The sample microcontrollers
provided with the PICDEM 1 demonstration board can
be programmed with a PRO MATE II device programmer, or a PICSTART Plus development programmer.
The PICDEM 1 demonstration board can be connected
to the MPLAB ICE in-circuit emulator for testing. A prototype area extends the circuitry for additional application components. Features include an RS-232
interface, a potentiometer for simulated analog input,
push button switches and eight LEDs.
The PICDEM 3 demonstration board supports the
PIC16C923 and PIC16C924 in the PLCC package. All
the necessary hardware and software is included to run
the demonstration programs.
17.15 PICDEM.net Internet/Ethernet
Demonstration Board
The PICDEM.net demonstration board is an Internet/
Ethernet demonstration board using the PIC18F452
microcontroller and TCP/IP firmware. The board
supports any 40-pin DIP device that conforms to the
standard pinout used by the PIC16F877 or
PIC18C452. This kit features a user friendly TCP/IP
stack, web server with HTML, a 24L256 Serial
EEPROM for Xmodem download to web pages into
Serial EEPROM, ICSP/MPLAB ICD 2 interface connector, an Ethernet interface, RS-232 interface, and a
16 x 2 LCD display. Also included is the book and
CD-ROM “TCP/IP Lean, Web Servers for Embedded
Systems,” by Jeremy Bentham
17.16 PICDEM 2 Plus
Demonstration Board
The PICDEM 2 Plus demonstration board supports
many 18-, 28-, and 40-pin microcontrollers, including
PIC16F87X and PIC18FXX2 devices. All the necessary hardware and software is included to run the demonstration programs. The sample microcontrollers
provided with the PICDEM 2 demonstration board can
be programmed with a PRO MATE II device programmer, PICSTART Plus development programmer, or
MPLAB ICD 2 with a Universal Programmer Adapter.
The MPLAB ICD 2 and MPLAB ICE in-circuit emulators
may also be used with the PICDEM 2 demonstration
board to test firmware. A prototype area extends the
circuitry for additional application components. Some
of the features include an RS-232 interface, a 2 x 16
LCD display, a piezo speaker, an on-board temperature
sensor, four LEDs, and sample PIC18F452 and
PIC16F877 FLASH microcontrollers.
DS30487B-page 160
17.18 PICDEM 4 8/14/18-Pin
Demonstration Board
The PICDEM 4 can be used to demonstrate the capabilities of the 8-, 14-, and 18-pin PIC16XXXX and
PIC18XXXX MCUs, including the PIC16F818/819,
PIC16F87/88, PIC16F62XA and the PIC18F1320 family of microcontrollers. PICDEM 4 is intended to showcase the many features of these low pin count parts,
including LIN and Motor Control using ECCP. Special
provisions are made for low-power operation with the
supercapacitor circuit, and jumpers allow on-board
hardware to be disabled to eliminate current draw in
this mode. Included on the demo board are provisions
for Crystal, RC or Canned Oscillator modes, a five volt
regulator for use with a nine volt wall adapter or battery,
DB-9 RS-232 interface, ICD connector for programming via ICSP and development with MPLAB ICD 2,
2x16 liquid crystal display, PCB footprints for H-Bridge
motor driver, LIN transceiver and EEPROM. Also
included are: header for expansion, eight LEDs, four
potentiometers, three push buttons and a prototyping
area. Included with the kit is a PIC16F627A and a
PIC18F1320. Tutorial firmware is included along with
the User’s Guide.
17.19 PICDEM 17 Demonstration Board
The PICDEM 17 demonstration board is an evaluation
board that demonstrates the capabilities of several
Microchip microcontrollers, including PIC17C752,
PIC17C756A, PIC17C762 and PIC17C766. A programmed sample is included. The PRO MATE II device
programmer, or the PICSTART Plus development programmer, can be used to reprogram the device for user
tailored application development. The PICDEM 17
demonstration board supports program download and
execution from external on-board FLASH memory. A
generous prototype area is available for user hardware
expansion.
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
17.20 PICDEM 18R PIC18C601/801
Demonstration Board
17.23 PICDEM USB PIC16C7X5
Demonstration Board
The PICDEM 18R demonstration board serves to assist
development of the PIC18C601/801 family of Microchip
microcontrollers. It provides hardware implementation
of both 8-bit Multiplexed/De-multiplexed and 16-bit
Memory modes. The board includes 2 Mb external
FLASH memory and 128 Kb SRAM memory, as well as
serial EEPROM, allowing access to the wide range of
memory types supported by the PIC18C601/801.
The PICDEM USB Demonstration Board shows off the
capabilities of the PIC16C745 and PIC16C765 USB
microcontrollers. This board provides the basis for
future USB products.
17.21 PICDEM LIN PIC16C43X
Demonstration Board
The powerful LIN hardware and software kit includes a
series of boards and three PICmicro microcontrollers.
The small footprint PIC16C432 and PIC16C433 are
used as slaves in the LIN communication and feature
on-board LIN transceivers. A PIC16F874 FLASH
microcontroller serves as the master. All three microcontrollers are programmed with firmware to provide
LIN bus communication.
17.22 PICkitTM 1 FLASH Starter Kit
A complete "development system in a box", the PICkit
FLASH Starter Kit includes a convenient multi-section
board for programming, evaluation, and development
of 8/14-pin FLASH PIC® microcontrollers. Powered via
USB, the board operates under a simple Windows GUI.
The PICkit 1 Starter Kit includes the user's guide (on
CD ROM), PICkit 1 tutorial software and code for various applications. Also included are MPLAB® IDE (Integrated Development Environment) software, software
and hardware "Tips 'n Tricks for 8-pin FLASH PIC®
Microcontrollers" Handbook and a USB Interface
Cable. Supports all current 8/14-pin FLASH PIC
microcontrollers, as well as many future planned
devices.
 2003 Microchip Technology Inc.
17.24 Evaluation and
Programming Tools
In addition to the PICDEM series of circuits, Microchip
has a line of evaluation kits and demonstration software
for these products.
• KEELOQ evaluation and programming tools for
Microchip’s HCS Secure Data Products
• CAN developers kit for automotive network
applications
• Analog design boards and filter design software
• PowerSmart battery charging evaluation/
calibration kits
• IrDA® development kit
• microID development and rfLabTM development
software
• SEEVAL® designer kit for memory evaluation and
endurance calculations
• PICDEM MSC demo boards for Switching mode
power supply, high-power IR driver, delta sigma
ADC, and flow rate sensor
Check the Microchip web page and the latest Product
Line Card for the complete list of demonstration and
evaluation kits.
Preliminary
DS30487B-page161
PIC16F87/88
NOTES:
DS30487B-page 162
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Ambient temperature under bias.............................................................................................................-55°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to VSS (except VDD and MCLR) ................................................... -0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS ............................................................................................................ -0.3 to +7.5V
Voltage on MCLR with respect to VSS (Note 2) .............................................................................................-0.3 to +14V
Total power dissipation (Note 1) ..................................................................................................................................1W
Maximum current out of VSS pin ...........................................................................................................................200 mA
Maximum current into VDD pin ..............................................................................................................................200 mA
Input clamp current, IIK (VI < 0 or VI > VDD)..................................................................................................................... ± 20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) ............................................................................................................. ± 20 mA
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by PORTA ........................................................................................................................100 mA
Maximum current sourced by PORTA...................................................................................................................100 mA
Maximum current sunk by PORTB........................................................................................................................100 mA
Maximum current sourced by PORTB ..................................................................................................................100 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD - VOH) x IOH} + ∑(VOl x IOL)
2: Voltage spikes at the MCLR pin may cause latch-up. A series resistor of greater than 1 kΩ should be used
to pull MCLR to VDD, rather than tying the pin directly to VDD.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 163
PIC16F87/88
FIGURE 18-1:
PIC16F87/88 VOLTAGE-FREQUENCY GRAPH
6.0V
5.5V
Voltage
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
2.0V
16 MHz
20 MHz
Frequency
FIGURE 18-2:
PIC16LF87/88 VOLTAGE-FREQUENCY GRAPH
6.0V
5.5V
Voltage
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
2.0V
4 MHz
10 MHz
Frequency
FMAX = (12 MHz/V) (VDDAPPMIN – 2.5V) + 4 MHz
Note 1: VDDAPPMIN is the minimum voltage of the PICmicro® device in the application.
Note 2: FMAX has a maximum frequency of 10 MHz.
DS30487B-page 164
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.1
DC Characteristics: Supply Voltage
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Symbol
VDD
Characteristic
Min
Typ
Max
Units
Conditions
Supply Voltage
D001
PIC16LF87/88
2.0
—
5.5
V
D001
PIC16F87/88
4.0
—
5.5
V
HS, XT, RC and LP Osc mode
D002
VDR
RAM Data Retention
Voltage(1)
1.5
—
—
V
D003
VPOR
VDD Start Voltage
to ensure internal
Power-on Reset signal
—
—
0.7
V
See Section 15.4 “Power-on Reset (POR)”
for details
D004
SVDD
VDD Rise Rate
to ensure internal
Power-on Reset signal
0.05
—
—
V/ms
See Section 15.4 “Power-on Reset (POR)”
for details
VBOR
Brown-out Reset Voltage
D005
PIC16LF87/88
3.65
—
4.35
V
D005
PIC16F87/88
3.65
—
4.35
V
Legend:
Note 1:
2:
FMAX = 14 MHz(2)
Shading of rows is to assist in readability of the table.
This is the limit to which VDD can be lowered in SLEEP mode, or during a device RESET, without losing RAM data.
When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 165
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
0.1
0.4
µA
-40°C
0.1
0.4
µA
25°C
0.4
1.5
µA
85°C
0.3
0.5
µA
-40°C
0.3
0.5
µA
25°C
0.7
1.7
µA
85°C
0.6
1.0
µA
-40°C
0.6
1.0
µA
25°C
1.2
5.0
µA
85°C
Power-down Current (IPD)(1)
PIC16LF87/88
PIC16LF87/88
All devices
Legend:
Note 1:
2:
3:
VDD = 2.0V
VDD = 3.0V
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
DS30487B-page 166
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
9
20
µA
-40°C
7
15
µA
25°C
Supply Current (IDD)(2,3)
PIC16LF87/88
PIC16LF87/88
All devices
PIC16LF87/88
PIC16LF87/88
All devices
PIC16LF87/88
PIC16LF87/88
All devices
Legend:
Note 1:
2:
3:
7
15
µA
85°C
16
30
µA
-40°C
14
25
µA
25°C
14
25
µA
85°C
32
40
µA
-40°C
26
35
µA
25°C
26
35
µA
85°C
72
95
µA
-40°C
76
90
µA
25°C
76
90
µA
85°C
138
175
µA
-40°C
136
170
µA
25°C
136
170
µA
85°C
310
380
µA
-40°C
290
360
µA
25°C
280
360
µA
85°C
270
315
µA
-40°C
280
310
µA
25°C
285
310
µA
85°C
460
610
µA
-40°C
450
600
µA
25°C
450
600
µA
85°C
900
1060
µA
-40°C
890
1050
µA
25°C
890
1050
µA
85°C
VDD = 2.0V
VDD = 3.0V
FOSC = 32 kHZ
(LP Oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHZ
(RC Oscillator)(3)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(RC Oscillator)(3)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 167
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
Supply Current (IDD)(2,3)
All devices
All devices
Legend:
Note 1:
2:
3:
1.8
2.3
mA
-40°C
1.6
2.2
mA
25°C
1.3
2.2
mA
85°C
3.0
4.2
mA
-40°C
2.5
4.0
mA
25°C
2.5
4.0
mA
85°C
VDD = 4.0V
FOSC = 20 MHZ
(HS Oscillator)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
DS30487B-page 168
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
8
20
µA
-40°C
7
15
µA
25°C
Supply Current (IDD)(2,3)
PIC16LF87/88
PIC16LF87/88
All devices
PIC16LF87/88
PIC16LF87/88
All devices
PIC16LF87/88
PIC16LF87/88
All devices
Legend:
Note 1:
2:
3:
7
15
µA
85°C
16
30
µA
-40°C
14
25
µA
25°C
14
25
µA
85°C
32
40
µA
-40°C
29
35
µA
25°C
29
35
µA
85°C
132
160
µA
-40°C
126
155
µA
25°C
126
155
µA
85°C
260
310
µA
-40°C
230
300
µA
25°C
230
300
µA
85°C
560
690
µA
-40°C
500
650
µA
25°C
500
650
µA
85°C
310
420
µA
-40°C
300
410
µA
25°C
300
410
µA
85°C
550
650
µA
-40°C
530
620
µA
25°C
530
620
µA
85°C
1.2
1.5
mA
-40°C
1.1
1.4
mA
25°C
1.1
1.4
mA
85°C
VDD = 2.0V
VDD = 3.0V
FOSC = 31.25 kHz
(RC_RUN mode,
Internal RC Oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 1 MHz
(RC_RUN mode,
Internal RC Oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
Internal RC Oscillator)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 169
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
Supply Current (IDD)(2,3)
PIC16LF87/88
All devices
PIC16LF87/88
PIC16LF87/88
All devices
Legend:
Note 1:
2:
3:
.950
1.3
mA
-40°C
.930
1.2
mA
25°C
.930
1.2
mA
85°C
1.8
3.0
mA
-40°C
1.7
2.8
mA
25°C
1.7
2.8
mA
85°C
9
13
µA
-10°C
9
14
µA
25°C
11
16
µA
70°C
12
34
µA
-10°C
12
31
µA
25°C
14
28
µA
70°C
20
72
µA
-10°C
20
65
µA
25°C
25
59
µA
70°C
VDD = 3.0V
FOSC = 8 MHz
(RC_RUN mode,
Internal RC Oscillator)
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
FOSC = 32 kHz
(SEC_RUN mode,
Timer1 as clock)
VDD = 5.0V
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
DS30487B-page 170
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.2
DC Characteristics: Power-down and Supply Current
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F87/88
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ
Max
Units
Conditions
Module Differential Currents (∆IWDT, ∆IBOR, ∆ILVD, ∆IOSCB, ∆IAD)
D022
(∆IWDT)
Watchdog Timer
1.5
3.8
µA
-40°C
2.2
3.8
µA
25°C
2.7
4.0
µA
85°C
2.3
4.6
µA
-40°C
2.7
4.6
µA
25°C
3.1
4.8
µA
85°C
3.0
10.0
µA
-40°C
3.3
10.0
µA
25°C
VDD = 2.0V
VDD = 3.0V
VDD = 5.0V
3.9
13.0
µA
85°C
D022A
(∆IBOR)
Brown-out Reset
40
60
µA
-40°C to +85°C
D025
(∆IOSCB)
Timer1 Oscillator
1.7
2.3
µA
-40°C
1.8
2.3
µA
25°C
2.0
2.3
µA
85°C
2.2
3.8
µA
-40°C
2.6
3.8
µA
25°C
2.9
3.8
µA
85°C
3.0
6.0
µA
-40°C
3.2
6.0
µA
25°C
3.4
7.0
µA
85°C
A/D Converter 0.001
2.0
µA
-40°C to +85°C
VDD = 2.0V
0.001
2.0
µA
-40°C to +85°C
VDD = 3.0V
0.003
2.0
µA
-40°C to +85°C
VDD = 5.0V
D026
(∆IAD)
Legend:
Note 1:
2:
3:
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
32 kHz on Timer1
VDD = 5.0V
A/D on, not converting
Shading of rows is to assist in readability of the table.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 171
PIC16F87/88
18.3
DC Characteristics: Internal RC Accuracy
PIC16F87/88 (Industrial)
PIC16LF87/88 (Industrial)
PIC16LF87/88
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
(Industrial)
PIC16F87/88
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
(Industrial)
Param
No.
Device
Min
Typ
Max
Units
Conditions
INTOSC Accuracy @ Freq = 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 125 kHz(1)
PIC16LF87/88
PIC16F87/88
-2
±1
2
%
25°C
VDD = 2.7-3.3V
-5
—
5
%
-10°C - +85°C
VDD = 2.7-3.3V
-10
—
10
%
-40°C - +85°C
VDD = 2.7-3.3V
-2
±1
2
%
25°C
VDD = 4.5-5.5V
-5
—
5
%
-10°C - +85°C
VDD = 4.5-5.5V
-10
—
10
%
-40°C - +85°C
VDD = 4.5-5.5V
INTRC Accuracy @ Freq = 31 kHz(2)
Legend:
Note 1:
2:
PIC16LF87/88
26.562
—
35.938
kHz
-40°C - +85°C
VDD = 2.7-3.3V
PIC16F87/88
26.562
—
35.938
kHz
-40°C - +85°C
VDD = 4.5-5.5V
Shading of rows is to assist in readability of the table.
Frequency calibrated at 25°C. OSCTUNE register can be used to compensate for temperature drift.
INTRC frequency after calibration.
DS30487B-page 172
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
18.4
DC Characteristics:
PIC16F87/88 (Industrial, Extended)
PIC16LF87/88 (Industrial)
DC CHARACTERISTICS
Param
Sym
No.
VIL
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Operating voltage VDD range as described in DC Specification,
Section 18.1 “DC Characteristics: Supply Voltage”.
Characteristic
Min
Typ†
Max
Units
Conditions
VSS
—
0.15 VDD
V
For entire VDD range
VSS
—
0.8V
V
4.5V ≤ VDD ≤ 5.5V
VSS
—
0.2 VDD
V
VSS
—
0.2 VDD
V
OSC1 (in XT and LP mode)
VSS
—
0.3V
V
OSC1 (in HS mode)
VSS
—
0.3 VDD
V
VSS
—
0.3 VDD
V
For entire VDD range
Input Low Voltage
I/O ports:
D030
with TTL buffer
D030A
D031
with Schmitt Trigger buffer
D032
MCLR, OSC1 (in RC mode)
D033
(Note 1)
Ports RB1 and RB4:
D034
with Schmitt Trigger buffer
VIH
Input High Voltage
I/O ports:
D040
2.0
—
VDD
V
4.5V ≤ VDD ≤ 5.5V
0.25 VDD + 0.8V
—
VDD
V
For entire VDD range
0.8 VDD
—
VDD
V
For entire VDD range
0.8 VDD
—
VDD
V
1.6V
—
VDD
V
with TTL buffer
D040A
D041
with Schmitt Trigger buffer
D042
MCLR
D042A
OSC1 (in XT and LP mode)
OSC1 (in HS mode)
0.7 VDD
—
VDD
V
D043
OSC1 (in RC mode)
0.9 VDD
—
VDD
V
(Note 1)
0.7 VDD
—
VDD
V
For entire VDD range
50
250
400
µA
VDD = 5V, VPIN = VSS
Ports RB1 and RB4:
D044
D070
with Schmitt Trigger buffer
IPURB PORTB Weak Pull-up Current
IIL
Input Leakage Current (Notes 2, 3)
D060
I/O ports
—
—
±1
µA
Vss ≤ VPIN ≤ VDD, pin at
high-impedance
D061
MCLR
—
—
±5
µA
Vss ≤ VPIN ≤ VDD
D063
OSC1
—
—
±5
µA
Vss ≤ VPIN ≤ VDD, XT, HS
and LP osc configuration
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PIC16F87/88 be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 173
PIC16F87/88
18.4
DC Characteristics:
PIC16F87/88 (Industrial, Extended)
PIC16LF87/88 (Industrial) (Continued)
DC CHARACTERISTICS
Param
Sym
No.
VOL
Characteristic
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Operating voltage VDD range as described in DC Specification,
Section 18.1 “DC Characteristics: Supply Voltage”.
Min
Typ†
Max
Units
Conditions
Output Low Voltage
D080
I/O ports
—
—
0.6
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +125°C
D083
OSC2/CLKO
(RC osc configuration)
—
—
0.6
V
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +125°C
VOH
Output High Voltage
D090
I/O ports (Note 3)
VDD – 0.7
—
—
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +125°C
D092
OSC2/CLKO
(RC osc configuration)
VDD – 0.7
—
—
V
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +125°C
—
—
15
pF
In XT, HS and LP modes
when external clock is used
to drive OSC1
Capacitive Loading Specs on Output Pins
D100
COSC2 OSC2 pin
D101
CIO
All I/O pins and OSC2
(in RC mode)
—
—
50
pF
D102
CB
SCL, SDA in I2C mode
—
—
400
pF
Data EEPROM Memory
D120
ED
Endurance
100K
10K
1M
100K
—
—
D121
VDRW VDD for read/write
VMIN
—
5.5
V
D122
TDEW Erase/write cycle time
—
4
8
ms
D130
EP
Endurance
10K
1K
100K
10K
—
—
E/W -40°C to 85°C
E/W +85°C to +125°C
D131
VPR
VDD for read
VMIN
—
5.5
V
VDD for erase/write
VMIN
—
5.5
V
E/W -40°C to 85°C
E/W +85°C to +125°C
Using EECON to read/write,
VMIN = min. operating voltage
Program FLASH Memory
D132A
Using EECON to read/write,
VMIN = min. operating voltage
D133
TPE
Erase cycle time
—
2
4
ms
D134
TPW
Write cycle time
—
2
4
ms
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PIC16F87/88 be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30487B-page 174
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 18-1:
COMPARATOR SPECIFICATIONS
Operating Conditions: 3.0V < VDD < 5.5V, -40°C < TA < +85°C, unless otherwise stated.
Param
No.
Characteristics
Sym
Min
Typ
Max
Units
D300
Input Offset Voltage
VIOFF
—
± 5.0
± 10
mV
D301
Input Common Mode Voltage*
VICM
0
-
VDD – 1.5
V
D302
Common Mode Rejection Ratio* CMRR
55
-
—
dB
TRESP
—
150
400
600
ns
ns
TMC2OV
—
—
10
µs
300
300A
Response
301
Comparator Mode Change to
Output Valid*
*
Note 1:
Time(1)*
Comments
PIC16F87/88
PIC16LF87/88
These parameters are characterized but not tested.
Response time measured with one comparator input at (VDD – 1.5)/2 while the other input transitions from
VSS to VDD.
TABLE 18-2:
VOLTAGE REFERENCE SPECIFICATIONS
Operating Conditions: 3.0V < VDD < 5.5V, -40°C < TA < +85°C, unless otherwise stated.
Spec
No.
Characteristics
Sym
Min
Typ
Max
Units
D310
Resolution
VRES
VDD/24
—
VDD/32
LSb
D311
Absolute Accuracy
VRAA
—
—
—
—
1/4
1/2
LSb
LSb
D312
Unit Resistor Value (R)*
VRUR
—
2k
—
Ω
TSET
—
—
10
µs
310
*
Note 1:
Settling Time
(1)*
Comments
Low Range (VRR = 1)
High Range (VRR = 0)
These parameters are characterized but not tested.
Settling time measured while VRR = 1 and VR<3:0> transitions from ‘0000’ to ‘1111’.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 175
PIC16F87/88
18.5
Timing Parameter Symbology
The timing parameter symbols have been created
using one of the following formats:
1. TppS2ppS
3. TCC:ST
(I2C specifications only)
2. TppS
4. Ts
(I2C specifications only)
T
F
Frequency
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
ck
CLKO
cs
CS
di
SDI
do
SDO
dt
Data in
io
I/O port
mc
MCLR
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (High-impedance)
L
Low
I2C only
AA
BUF
output access
Bus free
TCC:ST (I2C specifications only)
CC
HD
Hold
ST
DAT
DATA input hold
STA
START condition
FIGURE 18-3:
T
Time
osc
rd
rw
sc
ss
t0
t1
wr
OSC1
RD
RD or WR
SCK
SS
T0CKI
T1CKI
WR
P
R
V
Z
Period
Rise
Valid
High-impedance
High
Low
High
Low
SU
Setup
STO
STOP condition
LOAD CONDITIONS
Load Condition 1
Load Condition 2
VDD/2
RL
CL
Pin
VSS
RL = 464Ω
CL = 50 pF
15 pF
DS30487B-page 176
CL
Pin
VSS
for all pins except OSC2, but including PORTD and PORTE outputs as ports
for OSC2 output
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-4:
EXTERNAL CLOCK TIMING
Q4
Q1
Q2
Q3
Q4
Q1
OSC1
1
3
4
3
4
2
CLKO
TABLE 18-3:
Parameter
No.
EXTERNAL CLOCK TIMING REQUIREMENTS
Sym
FOSC
Characteristic
External CLKI Frequency
(Note 1)
Oscillator Frequency
(Note 1)
1
TOSC
External CLKI Period
(Note 1)
Oscillator Period
(Note 1)
Min
Typ†
Max
Units
DC
—
1
MHz XT and RC Osc mode
DC
—
20
MHz HS Osc mode
DC
—
32
kHz
DC
—
4
MHz RC Osc mode
0.1
—
4
MHz XT Osc mode
4
5
—
—
20
200
MHz HS Osc mode
kHz LP Osc mode
1000
—
—
ns
Conditions
LP Osc mode
XT and RC Osc mode
50
—
—
ns
HS Osc mode
5
—
—
ms
LP Osc mode
250
—
—
ns
RC Osc mode
250
—
10,000
ns
XT Osc mode
50
—
250
ns
HS Osc mode
5
—
—
ms
LP Osc mode
ns
TCY = 4/FOSC
2
TCY
Instruction Cycle Time
(Note 1)
200
TCY
DC
3
TosL,
TosH
External Clock in (OSC1) High or
Low Time
500
—
—
ns
XT oscillator
2.5
—
—
ms
LP oscillator
15
—
—
ns
HS oscillator
TosR,
TosF
External Clock in (OSC1) Rise or
Fall Time
—
—
25
ns
XT oscillator
4
—
—
50
ns
LP oscillator
—
—
15
ns
HS oscillator
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values
are based on characterization data for that particular oscillator type under standard operating conditions,
with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “min.” values
with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the “max.”
cycle time limit is “DC” (no clock) for all devices.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 177
PIC16F87/88
FIGURE 18-5:
CLKO AND I/O TIMING
Q1
Q4
Q2
Q3
OSC1
11
10
CLKO
13
19
14
12
18
16
I/O Pin
(Input)
15
17
I/O Pin
(Output)
New Value
Old Value
20, 21
Note: Refer to Figure 18-3 for load conditions.
TABLE 18-4:
Param
No.
CLKO AND I/O TIMING REQUIREMENTS
Symbol
Characteristic
Min
Typ†
Max
Units Conditions
10*
TosH2ckL
OSC1↑ to CLKO↓
—
75
200
ns
(Note 1)
11*
TosH2ckH OSC1↑ to CLKO↑
—
75
200
ns
(Note 1)
12*
TckR
CLKO rise time
—
35
100
ns
(Note 1)
13*
TckF
CLKO fall time
—
35
100
ns
(Note 1)
14*
TckL2ioV
CLKO ↓ to Port out valid
—
—
0.5 TCY + 20
ns
(Note 1)
15*
TioV2ckH
Port in valid before CLKO ↑
TOSC + 200
—
—
ns
(Note 1)
16*
TckH2ioI
Port in hold after CLKO ↑
0
—
—
ns
(Note 1)
17*
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid
—
100
255
ns
18*
TosH2ioI
OSC1↑ (Q2 cycle) to
Port input invalid (I/O in
hold time)
PIC16F87/88
100
—
—
ns
PIC16LF87/88
200
—
—
ns
—
ns
ns
19*
TioV2osH
Port input valid to OSC1↑ (I/O in setup time)
0
—
20*
TIOR
Port output rise time
PIC16F87/88
—
10
40
PIC16LF87/88
—
—
145
ns
PIC16F87/88
—
10
40
ns
PIC16LF87/88
—
—
145
ns
21*
TIOF
Port output fall time
22††*
TINP
INT pin high or low time
TCY
—
—
ns
23††*
TRBP
RB7:RB4 change INT high or low time
TCY
—
—
ns
*
†
††
Note 1:
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
These parameters are asynchronous events not related to any internal clock edges.
Measurements are taken in RC mode where CLKO output is 4 x TOSC.
DS30487B-page 178
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-6:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND
POWER-UP TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
Reset
31
34
34
I/O Pins
Note: Refer to Figure 18-3 for load conditions.
FIGURE 18-7:
BROWN-OUT RESET TIMING
VBOR
VDD
35
TABLE 18-5:
Parameter
No.
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET REQUIREMENTS
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
30
TmcL
MCLR Pulse Width (Low)
2
—
—
µs
VDD = 5V, -40°C to +85°C
31*
TWDT
Watchdog Timer Time-out Period
(16-bit prescaler = 0100 and no
postscaler)
TBD
16
TBD
ms
VDD = 5V, -40°C to +85°C
32
TOST
Oscillation Start-up Timer Period
—
1024 TOSC
—
—
TOSC = OSC1 period
33*
TPWRT
Power-up Timer Period
TBD
72
TBD
ms
VDD = 5V, -40°C to +85°C
34
TIOZ
I/O High-impedance from MCLR
Low or Watchdog Timer Reset
—
—
2.1
µs
TBOR
Brown-out Reset Pulse Width
100
—
—
µs
35
*
†
VDD ≤ VBOR (D005)
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 179
PIC16F87/88
FIGURE 18-8:
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
RB6/T1OSO/T1CKI
46
45
47
48
TMR0 or TMR1
Note: Refer to Figure 18-3 for load conditions.
TABLE 18-6:
Param
No.
40*
41*
42*
45*
TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Symbol
Tt0H
Tt0L
Tt0P
Tt1H
Characteristic
T0CKI High Pulse Width
T0CKI Low Pulse Width
T0CKI Period
T1CKI High
Time
Min
Typ†
Max
Units
No Prescaler
0.5 TCY + 20
—
—
ns
With Prescaler
10
—
—
ns
No Prescaler
0.5 TCY + 20
—
—
ns
With Prescaler
10
—
—
ns
No Prescaler
TCY + 40
—
—
ns
With Prescaler
Greater of:
20 or TCY + 40
N
—
—
ns
N = prescale value
(2, 4, ..., 256)
Must also meet
parameter 47
0.5 TCY + 20
—
—
ns
Synchronous,
PIC16F87/88
Prescaler = 2,4,8 PIC16LF87/88
15
—
—
ns
25
—
—
ns
Asynchronous
30
—
—
ns
Synchronous, Prescaler = 1
PIC16F87/88
PIC16LF87/88
46*
47*
Tt1L
Tt1P
T1CKI Low
Time
T1CKI Input
Period
50
—
—
ns
0.5 TCY + 20
—
—
ns
Synchronous,
PIC16F87/88
Prescaler = 2,4,8 PIC16LF87/88
15
—
—
ns
25
—
—
ns
Asynchronous
PIC16F87/88
30
—
—
ns
PIC16LF87/88
50
—
—
ns
PIC16F87/88
Greater of:
30 or TCY + 40
N
—
—
ns
PIC16LF87/88
Greater of:
50 or TCY + 40
N
Synchronous, Prescaler = 1
Synchronous
Asynchronous
Ft1
48
60
—
—
PIC16LF87/88
100
—
—
ns
DC
—
32.768
kHz
2 TOSC
—
7 TOSC
—
TCKEZtmr1 Delay from External Clock Edge to Timer Increment
*
†
Must also meet
parameter 42
Must also meet
parameter 42
Must also meet
parameter 47
N = prescale value
(1, 2, 4, 8)
N = prescale value
(1, 2, 4, 8)
PIC16F87/88
Timer1 Oscillator Input Frequency Range
(Oscillator enabled by setting bit T1OSCEN)
Conditions
ns
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
DS30487B-page 180
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-9:
CAPTURE/COMPARE/PWM TIMINGS (CCP1)
CCP1
(Capture Mode)
50
51
52
CCP1
(Compare or PWM Mode)
53
54
Note: Refer to Figure 18-3 for load conditions.
TABLE 18-7:
CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1)
Param
Symbol
No.
50*
TccL
Characteristic
CCP1
No Prescaler
Input Low Time
Min
PIC16F87/88
With Prescaler PIC16LF87/88
51*
TccH
CCP1
No Prescaler
Input High Time
PIC16F87/88
With Prescaler PIC16LF87/88
Typ† Max Units
0.5 TCY + 20
—
—
ns
10
—
—
ns
20
—
—
ns
0.5 TCY + 20
—
—
ns
10
—
—
ns
20
—
—
ns
3 TCY + 40
N
—
—
ns
—
10
25
ns
52*
TccP
CCP1 Input Period
53*
TccR
CCP1 Output Rise Time
PIC16F87/88
PIC16LF87/88
—
25
50
ns
54*
TccF
CCP1 Output Fall Time
PIC16F87/88
—
10
25
ns
PIC16LF87/88
—
25
45
ns
Conditions
N = prescale
value (1,4 or 16)
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 181
PIC16F87/88
FIGURE 18-10:
SPI MASTER MODE TIMING (CKE = 0, SMP = 0)
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
Bit 6 - - - - - -1
MSb
SDO
LSb
75, 76
SDI
Bit 6 - - - -1
MSb In
LSb In
74
73
Note: Refer to Figure 18-3 for load conditions.
FIGURE 18-11:
SPI MASTER MODE TIMING (CKE = 1, SMP = 1)
SS
81
SCK
(CKP = 0)
71
72
79
73
SCK
(CKP = 1)
80
78
SDO
MSb
Bit 6 - - - - - -1
LSb
Bit 6 - - - -1
LSb In
75, 76
SDI
MSb In
74
Note: Refer to Figure 18-3 for load conditions.
DS30487B-page 182
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-12:
SPI SLAVE MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
83
71
72
78
79
79
78
SCK
(CKP = 1)
80
LSb
Bit 6 - - - - - -1
MSb
SDO
77
75, 76
SDI
MSb In
Bit 6 - - - -1
LSb In
74
73
Note: Refer to Figure 18-3 for load conditions.
FIGURE 18-13:
SPI SLAVE MODE TIMING (CKE = 1)
82
SS
SCK
(CKP = 0)
70
83
71
72
SCK
(CKP = 1)
80
MSb
SDO
Bit 6 - - - - - -1
LSb
75, 76
SDI
MSb In
77
Bit 6 - - - -1
LSb In
74
Note: Refer to Figure 18-3 for load conditions.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 183
PIC16F87/88
TABLE 18-8:
Param
No.
SPI MODE REQUIREMENTS
Symbol
Characteristic
Min
Typ†
Max
Units
TCY
—
—
ns
70*
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
71*
TscH
SCK input high time (Slave mode)
TCY + 20
—
—
ns
72*
TscL
SCK input low time (Slave mode)
TCY + 20
—
—
ns
73*
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK edge
100
—
—
ns
74*
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK edge
100
—
—
ns
75*
TdoR
SDO data output rise time
—
—
10
25
25
50
ns
ns
76*
TdoF
SDO data output fall time
—
10
25
ns
PIC16F87/88
PIC16LF87/88
77*
TssH2doZ
SS↑ to SDO output high-impedance
78*
TscR
SCK output rise time
(Master mode)
79*
TscF
SCK output fall time (Master mode)
80*
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
81*
TdoV2scH,
TdoV2scL
SDO data output setup to SCK edge
PIC16F87/88
PIC16LF87/88
PIC16F87/88
PIC16LF87/88
82*
TssL2doV
SDO data output valid after SS↓ edge
83*
TscH2ssH,
TscL2ssH
SS ↑ after SCK edge
*
†
10
—
50
ns
—
—
10
25
25
50
ns
ns
—
10
25
ns
—
—
—
—
50
145
ns
ns
TCY
—
—
ns
—
—
50
ns
1.5 TCY + 40
—
—
ns
Conditions
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
I2C BUS START/STOP BITS TIMING
FIGURE 18-14:
SCL
91
93
90
92
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 18-3 for load conditions.
DS30487B-page 184
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
TABLE 18-9:
Param
No.
90*
I2C BUS START/STOP BITS REQUIREMENTS
Symbol
TSU:STA
91*
THD:STA
92*
TSU:STO
93
THD:STO
*
Characteristic
Min Typ Max Units
START condition
100 kHz mode
4700 —
—
Setup time
400 kHz mode
600
—
—
START condition
100 kHz mode
4000 —
—
Hold time
400 kHz mode
600
—
—
STOP condition
100 kHz mode
4700 —
—
Setup time
400 kHz mode
600
—
—
STOP condition
100 kHz mode
4000 —
—
Hold time
400 kHz mode
600
—
—
Conditions
ns
Only relevant for Repeated
START condition
ns
After this period, the first clock
pulse is generated
ns
ns
These parameters are characterized but not tested.
FIGURE 18-15:
I2C BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 18-3 for load conditions.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 185
PIC16F87/88
TABLE 18-10: I2C BUS DATA REQUIREMENTS
Param.
No.
100*
Symbol
THIGH
Characteristic
Clock high time
100 kHz mode
400 kHz mode
TLOW
Clock low time
TR
103*
TF
TSU:STA
90*
91*
THD:STA
106*
THD:DAT
TSU:DAT
107*
92*
TSU:STO
109*
TAA
110*
TBUF
CB
*
Note 1:
2:
Units
4.0
—
µs
µs
0.6
—
—
100 kHz mode
4.7
—
µs
400 kHz mode
1.3
—
µs
Conditions
1.5 TCY
—
—
1000
ns
CB
300
ns
100 kHz mode
—
300
ns
400 kHz mode
20 + 0.1 CB
300
ns
CB is specified to be from
10 - 400 pF
START condition
setup time
100 kHz mode
4.7
—
µs
400 kHz mode
0.6
—
µs
Only relevant for
Repeated START
condition
START condition
hold time
100 kHz mode
4.0
—
µs
400 kHz mode
0.6
—
µs
SSP Module
102*
Max
1.5 TCY
SSP Module
101*
Min
SDA and SCL rise
time
100 kHz mode
SDA and SCL fall
time
400 kHz mode
20 + 0.1
Data input hold time 100 kHz mode
0
—
ns
400 kHz mode
0
0.9
µs
Data input setup
time
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
STOP condition
setup time
100 kHz mode
4.7
—
µs
400 kHz mode
0.6
—
µs
Output valid from
clock
100 kHz mode
—
3500
ns
400 kHz mode
—
—
ns
Bus free time
100 kHz mode
4.7
—
µs
400 kHz mode
1.3
—
µs
—
400
pF
Bus capacitive loading
CB is specified to be from
10 - 400 pF
After this period, the first
clock pulse is generated
(Note 2)
(Note 1)
Time the bus must be free
before a new transmission
can start
These parameters are characterized but not tested.
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
A fast mode (400 kHz) I2C bus device can be used in a standard mode (100 kHz) I2C bus system, but the
requirement TSU:DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not
stretch the low period of the SCL signal. If such a device does stretch the low period of the SCL signal, it
must output the next data bit to the SDA line, TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the
standard mode I2C bus specification), before the SCL line is released.
DS30487B-page 186
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-16:
USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RB5/TX/CK
pin
121
121
RB2/RX/DT
pin
120
122
Note: Refer to Figure 18-3 for load conditions.
TABLE 18-11: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Param
No.
120
Sym
TckH2dtV
121
Tckrf
122
Tdtrf
†
Characteristic
Min
Typ†
Max
Units Conditions
PIC16F87/88
SYNC XMIT (MASTER &
SLAVE)
Clock high to data out valid
—
—
80
ns
PIC16LF87/88
—
—
100
ns
Clock out rise time and fall time PIC16F87/88
(Master mode)
PIC16LF87/88
—
—
45
ns
—
—
50
ns
Data out rise time and fall time
PIC16F87/88
—
—
45
ns
PIC16LF87/88
—
—
50
ns
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
FIGURE 18-17:
USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RB5/TX/CK
pin
125
RB2/RX/DT
pin
126
Note: Refer to Figure 18-3 for load conditions.
TABLE 18-12: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Param
No.
125
126
Sym
TdtV2ckL
TckL2dtl
Characteristic
Min
Typ†
Max
Units
SYNC RCV (MASTER & SLAVE)
Data setup before CK↓ (DT setup time)
15
—
—
ns
Data hold after CK↓ (DT hold time)
15
—
—
ns
Conditions
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 187
PIC16F87/88
TABLE 18-13: A/D CONVERTER CHARACTERISTICS: PIC16F87/88 (INDUSTRIAL, EXTENDED)
PIC16LF87/88 (INDUSTRIAL)
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
Conditions
A01
NR
Resolution
—
—
10 bits
bit
VREF = VDD = 5.12V,
VSS ≤ VAIN ≤ VREF
A03
EIL
Integral linearity error
—
—
<±1
LSb
VREF = VDD = 5.12V,
VSS ≤ VAIN ≤ VREF
A04
EDL
Differential linearity error
—
—
<±1
LSb
VREF = VDD = 5.12V,
VSS ≤ VAIN ≤ VREF
A06
EOFF
Offset error
—
—
<±2
LSb
VREF = VDD = 5.12V,
VSS ≤ VAIN ≤ VREF
A07
EGN
Gain error
—
—
<±1
LSb
VREF = VDD = 5.12V,
VSS ≤ VAIN ≤ VREF
A10
—
Monotonicity(3)
—
guaranteed
—
—
VSS ≤ VAIN ≤ VREF
A20
VREF
Reference Voltage
2.5
2.2
—
—
VDD + 0.3
VDD + 0.3
V
V
-40°C to +85°C
0°C to +85°C
A21
VREF+ Reference voltage high
AVDD – 2.5V
AVDD + 0.3V
V
A22
VREF- Reference voltage low
AVSS – 0.3V
VREF+ – 2.0V
V
A25
VAIN
Analog input voltage
VSS – 0.3V
—
VREF + 0.3V
V
A30
ZAIN
Recommended impedance of
analog voltage source
—
—
2.5
kΩ
See (Note 4)
A50
IREF
VREF input current(2)
—
—
5
µA
—
—
500
µA
During VAIN acquisition.
Based on differential of VHOLD to
VAIN to charge CHOLD, see
Section 12.1 “A/D Acquisition
Requirements”.
During A/D Conversion cycle.
†
Note 1:
2:
3:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
VREF current is from RA3 pin or VDD pin, whichever is selected as reference input.
The A/D conversion result never decreases with an increase in the input voltage, and has no missing codes.
The maximum allowed impedance for analog voltage source is 10 kΩ. This requires higher acquisition times.
DS30487B-page 188
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
FIGURE 18-18:
A/D CONVERSION TIMING
1 TCY
BSF ADCON0, GO
(TOSC/2)(1)
131
Q4
130
A/D CLK
132
9
A/D DATA
8
...
7
...
2
1
NEW_DATA
OLD_DATA
ADRES
0
ADIF
GO
DONE
SAMPLING STOPPED
SAMPLE
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEP instruction to be executed.
TABLE 18-14: A/D CONVERSION REQUIREMENTS
Param
No.
130
Sym
TAD
Characteristic
A/D clock period
Min
Typ†
Max
Units
PIC16F87/88
1.6
—
—
µs
TOSC based, VREF ≥ 3.0V
PIC16LF87/88
3.0
—
—
µs
TOSC based, VREF ≥ 2.0V
PIC16F87/88
2.0
4.0
6.0
µs
A/D RC mode
PIC16LF87/88
3.0
6.0
9.0
µs
A/D RC mode
—
12
TAD
(Note 2)
10*
40
—
—
—
µs
µs
—
TOSC/2
—
—
131
TCNV
Conversion time (not including S/H time)
(Note 1)
132
TACQ
Acquisition time
134
TGO
*
†
Note 1:
2:
Q4 to A/D clock start
Conditions
The minimum time is the
amplifier settling time. This may be
used if the “new” input voltage has
not changed by more than 1 LSb
(i.e., 20.0 mV @ 5.12V) from the last
sampled voltage (as stated on
CHOLD).
If the A/D clock source is selected as
RC, a time of TCY is added before the
A/D clock starts. This allows the
SLEEP instruction to be executed.
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
ADRES register may be read on the following TCY cycle.
See Section 12.1 “A/D Acquisition Requirements” for minimum conditions.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 189
PIC16F87/88
NOTES:
DS30487B-page 190
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
19.0
DC AND AC
CHARACTERISTICS GRAPHS
AND TABLES
No Graphs and Tables are available at this time.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 191
PIC16F87/88
NOTES:
DS30487B-page 192
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
20.0
PACKAGING INFORMATION
20.1
Package Marking Information
18-Lead PDIP
Example
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
YYWWNNN
PIC16F87/88-I/P
0310017
18-Lead SOIC
Example
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
PIC16F87/8804/SO
0310017
20-Lead SSOP
Example
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
PIC16F8720/SS
0310017
Example
28-Lead QFN
PIC16F87
-I/ML
0310017
XXXXXXXX
XXXXXXXX
YYWWNNN
Legend:
Note:
*
XX...X
Y
YY
WW
NNN
Customer specific information*
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line thus limiting the number of available characters
for customer specific information.
Standard PICmicro device marking consists of Microchip part number, year code, week code, and
traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check
with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP
price.
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 193
PIC16F87/88
18-Lead Plastic Dual In-line (P) – 300 mil (PDIP)
E1
D
2
n
α
1
E
A2
A
L
c
A1
B1
β
p
B
eB
Units
Dimension Limits
n
p
MIN
INCHES*
NOM
18
.100
.155
.130
MAX
MILLIMETERS
NOM
18
2.54
3.56
3.94
2.92
3.30
0.38
7.62
7.94
6.10
6.35
22.61
22.80
3.18
3.30
0.20
0.29
1.14
1.46
0.36
0.46
7.87
9.40
5
10
5
10
MIN
Number of Pins
Pitch
Top to Seating Plane
A
.140
.170
Molded Package Thickness
A2
.115
.145
Base to Seating Plane
A1
.015
Shoulder to Shoulder Width
E
.300
.313
.325
Molded Package Width
E1
.240
.250
.260
Overall Length
D
.890
.898
.905
Tip to Seating Plane
L
.125
.130
.135
c
Lead Thickness
.008
.012
.015
Upper Lead Width
B1
.045
.058
.070
Lower Lead Width
B
.014
.018
.022
Overall Row Spacing
§
eB
.310
.370
.430
α
Mold Draft Angle Top
5
10
15
β
Mold Draft Angle Bottom
5
10
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MS-001
Drawing No. C04-007
DS30487B-page 194
Preliminary
MAX
4.32
3.68
8.26
6.60
22.99
3.43
0.38
1.78
0.56
10.92
15
15
 2003 Microchip Technology Inc.
PIC16F87/88
18-Lead Plastic Small Outline (SO) – Wide, 300 mil (SOIC)
E
p
E1
D
2
B
n
1
h
α
45°
c
A2
A
φ
β
L
Units
Dimension Limits
n
p
Number of Pins
Pitch
Overall Height
Molded Package Thickness
Standoff §
Overall Width
Molded Package Width
Overall Length
Chamfer Distance
Foot Length
Foot Angle
Lead Thickness
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
A
A2
A1
E
E1
D
h
L
φ
c
B
α
β
MIN
.093
.088
.004
.394
.291
.446
.010
.016
0
.009
.014
0
0
A1
INCHES*
NOM
18
.050
.099
.091
.008
.407
.295
.454
.020
.033
4
.011
.017
12
12
MAX
.104
.094
.012
.420
.299
.462
.029
.050
8
.012
.020
15
15
MILLIMETERS
NOM
18
1.27
2.36
2.50
2.24
2.31
0.10
0.20
10.01
10.34
7.39
7.49
11.33
11.53
0.25
0.50
0.41
0.84
0
4
0.23
0.27
0.36
0.42
0
12
0
12
MIN
MAX
2.64
2.39
0.30
10.67
7.59
11.73
0.74
1.27
8
0.30
0.51
15
15
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MS-013
Drawing No. C04-051
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 195
PIC16F87/88
20-Lead Plastic Shrink Small Outline (SS) – 209 mil, 5.30 mm (SSOP)
E
E1
p
D
B
2
1
n
α
c
A2
A
φ
L
A1
β
Units
Dimension Limits
n
p
Number of Pins
Pitch
Overall Height
Molded Package Thickness
Standoff §
Overall Width
Molded Package Width
Overall Length
Foot Length
Lead Thickness
Foot Angle
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
A
A2
A1
E
E1
D
L
c
φ
B
α
β
MIN
.068
.064
.002
.299
.201
.278
.022
.004
0
.010
0
0
INCHES*
NOM
20
.026
.073
.068
.006
.309
.207
.284
.030
.007
4
.013
5
5
MAX
.078
.072
.010
.322
.212
.289
.037
.010
8
.015
10
10
MILLIMETERS
NOM
20
0.65
1.73
1.85
1.63
1.73
0.05
0.15
7.59
7.85
5.11
5.25
7.06
7.20
0.56
0.75
0.10
0.18
0.00
101.60
0.25
0.32
0
5
0
5
MIN
MAX
1.98
1.83
0.25
8.18
5.38
7.34
0.94
0.25
203.20
0.38
10
10
* Controlling Parameter
§ Significant Characteristic
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed
.010” (0.254mm) per side.
JEDEC Equivalent: MO-150
Drawing No. C04-072
DS30487B-page 196
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
28-Lead Plastic Quad Flat No Lead Package (ML) 6x6 mm Body, Punch Singulated (QFN)
EXPOSED
METAL
PADS
E
E1
Q
D1
D
D2
p
2
1
B
n
R
E2
CH X 45°
TOP VIEW
L
BOTTOM VIEW
α
A2
A
A1
A3
Units
Dimension Limits
n
p
Number of Pins
Pitch
Overall Height
Molded Package Thickness
Standoff
Base Thickness
Overall Width
Molded Package Width
Exposed Pad Width
Overall Length
Molded Package Length
Exposed Pad Length
Lead Width
Lead Length
Tie Bar Width
Tie Bar Length
Chamfer
Mold Draft Angle Top
A
A2
A1
A3
E
E1
E2
D
D1
D2
B
L
R
Q
CH
α
MIN
.000
.140
.140
.009
.020
.005
.012
.009
INCHES
NOM
28
.026 BSC
.033
.026
.0004
.008 REF
.236 BSC
.226 BSC
.146
.236 BSC
.226 BSC
.146
.011
.024
.007
.016
.017
MAX
.039
.031
.002
.152
.152
.014
.030
.010
.026
.024
12°
MILLIMETERS*
NOM
28
0.65 BSC
0.85
0.65
0.00
0.01
0.20 REF
6.00 BSC
5.75 BSC
3.55
3.70
6.00 BSC
5.75 BSC
3.55
3.70
0.23
0.28
0.50
0.60
0.13
0.17
0.30
0.40
0.24
0.42
MIN
MAX
1.00
0.80
0.05
3.85
3.85
0.35
0.75
0.23
0.65
0.60
12°
*Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not
exceed .010" (0.254mm) per side.
JEDEC equivalent: mMO-220
Drawing No. C04-114
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 197
PIC16F87/88
NOTES:
DS30487B-page 198
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
APPENDIX A:
REVISION HISTORY
APPENDIX B:
Revision A (November 2003)
DEVICE
DIFFERENCES
Original data sheet for PIC16F87/88 devices.
The differences between the devices in this data sheet
are listed in Table B-1.
Revision B (August 2003)
TABLE B-1:
The specifications in Section 18.0 “Electrical
Characteristics” have been updated to include the
addition of maximum specifications to the DC
Characteristics tables, text clarification has been made
to Section 4.6.2 “Clock Switching”, and there have
been minor updates to the data sheet text.
 2003 Microchip Technology Inc.
Features
Analog-to-Digital
Converter
Preliminary
DIFFERENCES BETWEEN
THE PIC16F87 AND PIC16F88
PIC16F87
PIC16F88
N/A
10-bit, 7-channel
DS30487B-page 199
PIC16F87/88
NOTES:
DS30487B-page 200
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
INDEX
A
A/D
Acquisition Requirements ........................................ 117
ADIF Bit .................................................................... 116
Analog-to-Digital Converter ...................................... 113
Associated Registers ............................................... 120
Calculating Acquisition Time .................................... 117
Configuring Analog Port Pins ................................... 118
Configuring the Interrupt .......................................... 116
Configuring the Module ............................................ 116
Conversion Clock ..................................................... 118
Conversions ............................................................. 119
Converter Characteristics ........................................ 188
Delays ...................................................................... 117
Effects of a RESET .................................................. 120
GO/DONE Bit ........................................................... 116
Internal Sampling Switch (Rss) Impedance ............. 117
Operation During SLEEP ......................................... 120
Result Registers ....................................................... 119
Source Impedance ................................................... 117
Time Delays ............................................................. 117
Using the CCP Trigger ............................................. 120
Absolute Maximum Ratings ............................................. 163
ACK .................................................................................... 93
ADCON0 Register ...................................................... 14, 113
ADCON1 Register ...................................................... 15, 113
Addressable Universal Synchronous Asynchronous
Receiver Transmitter. See USART.
ADRESH Register ...................................................... 14, 113
ADRESH, ADRESL Register Pair .................................... 116
ADRESL Register ...................................................... 15, 113
ANSEL Register ..............................................15, 52, 58, 113
Application Notes
AN556 (Implementing a Table Read) ........................ 25
AN578 (Use of the SSP Module in the
I2C Multi-Master Environment) ........................... 87
AN607 (Power-up Trouble Shooting) ....................... 133
Assembler
MPASM Assembler .................................................. 157
Asynchronous Reception
Associated Registers ....................................... 105, 107
Asynchronous Transmission
Associated Registers ............................................... 103
B
Baud Rate Generator
Associated Registers ................................................. 99
BF Bit ................................................................................. 92
Block Diagrams
A/D ........................................................................... 116
Analog Input Model .......................................... 117, 125
Capture Mode Operation ........................................... 82
Comparator I/O Operating Modes ............................ 122
Comparator Output .................................................. 124
Comparator Voltage Reference ............................... 128
Compare Mode Operation ......................................... 83
Fail-Safe Clock Monitor ............................................ 144
In-Circuit Serial Programming Connection ............... 147
Interrupt Logic .......................................................... 139
On-Chip Reset Circuit .............................................. 132
PIC16F87 ..................................................................... 6
PIC16F88 ..................................................................... 7
 2003 Microchip Technology Inc.
PWM .......................................................................... 84
RA0/AN0:RA1/AN1 Pins ............................................ 52
RA2/AN2/CVREF/VREF- Pin ....................................... 53
RA3/AN3/VREF+/C1OUT Pin ..................................... 53
RA4/T0CKI/C2OUT Pin ............................................. 54
RA5/MCLR/VPP Pin ................................................... 54
RA6/OSC2/CLKO Pin ................................................ 55
RA7/OSC1/CLKI Pin .................................................. 56
RB0 Pin ..................................................................... 59
RB1 Pin ..................................................................... 60
RB2 Pin ..................................................................... 61
RB3 Pin ..................................................................... 62
RB4 Pin ..................................................................... 63
RB5 Pin ..................................................................... 64
RB6 Pin ..................................................................... 65
RB7 Pin ..................................................................... 66
Recommended MCLR Circuit .................................. 133
SSP in I2C Mode ........................................................ 92
SSP in SPI Mode ....................................................... 90
System Clock ............................................................. 41
Timer0/WDT Prescaler .............................................. 67
Timer1 ....................................................................... 73
Timer2 ....................................................................... 79
USART Receive ................................................104, 106
USART Transmit ...................................................... 102
Watchdog Timer (WDT) ........................................... 141
BOR. See Brown-out Reset.
BRGH bit ............................................................................ 99
Brown-out Reset (BOR) ............................ 129, 132, 133, 135
BOR Status (BOR Bit) ............................................... 24
C
C Compilers
MPLAB C17 ............................................................. 158
MPLAB C18 ............................................................. 158
MPLAB C30 ............................................................. 158
Capture/Compare/PWM (CCP) ......................................... 81
Capture Mode ............................................................ 82
Capture, Compare and Timer1
Associated Registers ......................................... 83
CCP Pin Configuration ............................................... 83
CCP Prescaler ........................................................... 82
CCP Timer Resources ............................................... 81
CCP1IF ...................................................................... 82
CCPR1 ...................................................................... 82
CCPR1H:CCPR1L ..................................................... 82
Compare Mode .......................................................... 83
Special Event Trigger ........................................ 83
Special Trigger Output of CCP1 ........................ 83
PWM and Timer2 Associated Registers .................... 85
PWM Mode ................................................................ 84
PWM, Example Frequencies/Resolutions ................. 85
Software Interrupt Mode ............................................ 83
Timer1 Mode Selection .............................................. 83
CCP1CON Register ........................................................... 14
CCP1M0 Bit ....................................................................... 81
CCP1M1 Bit ....................................................................... 81
CCP1M2 Bit ....................................................................... 81
CCP1M3 Bit ....................................................................... 81
CCP1X Bit .......................................................................... 81
CCP1Y Bit .......................................................................... 81
CCPR1H Register .........................................................14, 81
Preliminary
DS30487B-page 201
PIC16F87/88
CCPR1L Register ......................................................... 14, 81
Clock Sources .................................................................... 39
Selection Using OSCCON Register ........................... 39
Clock Switching .................................................................. 39
Transition and the Watchdog Timer ........................... 40
CMCON Register ............................................................... 15
Code Examples
Call of a Subroutine in Page 1 from Page 0 ............... 25
Changing Between Capture Prescalers ..................... 82
Changing Prescaler Assignment from
WDT to Timer0 ................................................... 69
Erasing a FLASH Program Memory Row .................. 31
Implementing a Real-Time Clock Using a
Timer1 Interrupt Service .................................... 77
Indirect Addressing .................................................... 26
Initializing PORTA ...................................................... 51
Reading a 16-bit Free-Running Timer ........................ 74
Reading Data EEPROM ............................................. 29
Reading FLASH Program Memory ............................ 30
Saving STATUS, W and PCLATH Registers ........... 140
Writing a 16-bit Free-Running Timer .......................... 74
Writing to Data EEPROM ........................................... 29
Writing to FLASH Program Memory ........................... 33
Code Protection ....................................................... 129, 147
Comparator Module ......................................................... 121
Analog Input Connection Considerations ................. 125
Associated Registers ............................................... 126
Configuration ............................................................ 122
Effects of a RESET .................................................. 125
Interrupts .................................................................. 124
Operation ................................................................. 123
Operation During SLEEP ......................................... 125
Outputs ..................................................................... 123
Reference ................................................................. 123
Response Time ........................................................ 123
Comparator Specifications ............................................... 175
Comparator Voltage Reference ....................................... 127
Associated Registers ............................................... 128
Computed GOTO ............................................................... 25
Configuration Bits ............................................................. 129
Crystal and Ceramic Resonators ....................................... 35
CVRCON Register ............................................................. 15
D
Data EEPROM Memory ..................................................... 27
Associated Registers ................................................. 34
EEADR Register ........................................................ 27
EEADRH Register ...................................................... 27
EECON1 Register ...................................................... 27
EECON2 Register ...................................................... 27
EEDATA Register ...................................................... 27
EEDATH Register ...................................................... 27
Operation During Code Protect .................................. 34
Protection Against Spurious Writes ............................ 34
Reading ...................................................................... 29
Write Complete Flag (EEIF Bit) .................................. 27
Writing ........................................................................ 29
Data Memory
Special Function Registers ........................................ 14
DC and AC Characteristics
Graphs and Tables ................................................... 191
DC Characteristics
Internal RC Accuracy ............................................... 172
PIC16F87/88, PIC16LF87/88 ................................... 173
Power-down and Supply Current ............................. 166
Supply Voltage ......................................................... 165
DS30487B-page 202
Demonstration Boards
PICDEM 1 ................................................................ 160
PICDEM 17 .............................................................. 160
PICDEM 18R PIC18C601/801 ................................. 161
PICDEM 2 Plus ........................................................ 160
PICDEM 3 PIC16C92X ............................................ 160
PICDEM 4 ................................................................ 160
PICDEM LIN PIC16C43X ........................................ 161
PICDEM USB PIC16C7X5 ...................................... 161
PICDEM.net Internet/Ethernet ................................. 160
Development Support ...................................................... 157
Device Differences ........................................................... 199
Device Overview .................................................................. 5
Direct Addressing ............................................................... 26
E
EEADR Register ...........................................................16, 27
EEADRH Register .........................................................16, 27
EECON1 Register .........................................................16, 27
EECON2 Register .........................................................16, 27
EEDATA Register .........................................................16, 27
EEDATH Register .........................................................16, 27
Electrical Characteristics .................................................. 163
Endurance ........................................................................... 1
Errata ................................................................................... 4
Evaluation and Programming Tools ................................. 161
Exiting SLEEP with an Interrupt ......................................... 50
External Clock Input ........................................................... 36
External Clock Input (RA4/T0CKI). See Timer0.
External Interrupt Input (RB0/INT). See Interrupt Sources.
External Reference Signal ............................................... 123
F
Fail-Safe Clock Monitor .............................................129, 144
FLASH Program Memory ................................................... 27
Associated Registers ................................................. 34
EEADR Register ........................................................ 27
EEADRH Register ..................................................... 27
EECON1 Register ...................................................... 27
EECON2 Register ...................................................... 27
EEDATA Register ...................................................... 27
EEDATH Register ...................................................... 27
Erasing ....................................................................... 30
Reading ..................................................................... 30
Writing ........................................................................ 32
FSR Register ..........................................................14, 15, 26
I
I/O Ports ............................................................................. 51
PORTA ...................................................................... 51
PORTB ...................................................................... 57
TRISB Register .......................................................... 57
I2C
Addressing ................................................................. 93
Associated Registers ................................................. 95
Master Mode .............................................................. 95
Mode .......................................................................... 92
Mode Selection .......................................................... 92
Multi-Master Mode ..................................................... 95
Reception ................................................................... 93
SCL and SDA pins ..................................................... 92
Slave Mode ................................................................ 92
Transmission ............................................................. 93
ID Locations ..............................................................129, 147
In-Circuit Debugger .......................................................... 147
In-Circuit Serial Programming .......................................... 129
 2003 Microchip Technology Inc.
PIC16F87/88
In-Circuit Serial Programming (ICSP) .............................. 147
INDF Register .........................................................14, 15, 26
Indirect Addressing ............................................................ 26
Instruction Set .................................................................. 149
ADDLW .................................................................... 151
ADDWF .................................................................... 151
ANDLW .................................................................... 151
ANDWF .................................................................... 151
BCF .......................................................................... 151
BSF .......................................................................... 151
BTFSC ..................................................................... 152
BTFSS ..................................................................... 152
CALL ........................................................................ 152
CLRF ........................................................................ 152
CLRW ...................................................................... 152
CLRWDT .................................................................. 152
COMF ...................................................................... 153
DECF ....................................................................... 153
DECFSZ ................................................................... 153
Descriptions ............................................................. 151
Format ...................................................................... 149
GOTO ...................................................................... 153
INCF ......................................................................... 153
INCFSZ .................................................................... 153
IORLW ..................................................................... 154
IORWF ..................................................................... 154
MOVF ....................................................................... 154
MOVLW ................................................................... 154
MOVWF ................................................................... 154
NOP ......................................................................... 154
Read-Modify-Write Operations ................................ 149
RETFIE .................................................................... 155
RETLW .................................................................... 155
RETURN .................................................................. 155
RLF .......................................................................... 155
RRF .......................................................................... 155
SLEEP ..................................................................... 155
SUBLW .................................................................... 156
SUBWF .................................................................... 156
Summary Table ........................................................ 150
SWAPF .................................................................... 156
XORLW .................................................................... 156
XORWF .................................................................... 156
INT Interrupt (RB0/INT). See Interrupt Sources.
INTCON Register
GIE Bit ........................................................................ 19
INTE Bit ...................................................................... 19
INTF Bit ...................................................................... 19
PEIE Bit ...................................................................... 19
RBIE Bit ..................................................................... 19
RBIF Bit ...................................................................... 19
TMR0IE Bit ................................................................. 19
Internal Oscillator Block ..................................................... 37
INTRC Modes ............................................................ 38
Internal Reference Signal ................................................. 123
Interrupt Sources ...................................................... 129, 138
RB0/INT Pin, External .............................................. 140
TMR0 Overflow ........................................................ 140
USART Receive/Transmit Complete ......................... 97
Interrupts
RB7:RB4 Port Change ............................................... 57
Interrupts, Context Saving During .................................... 140
 2003 Microchip Technology Inc.
Interrupts, Enable Bits
A/D Converter Interrupt Enable (ADIE Bit) ................ 20
CCP1 Interrupt Enable (CCP1IE Bit) ......................... 20
Comparator Interrupt Enable (CMIE Bit) .................... 22
EEPROM Write Operation Interrupt Enable
(EEIE Bit) ........................................................... 22
Global Interrupt Enable (GIE Bit) ........................19, 138
Interrupt-on-Change (RB7:RB4) Enable
(RBIE Bit) ......................................................... 140
Oscillator Fail Interrupt Enable (OSFIE Bit) ............... 22
Peripheral Interrupt Enable (PEIE Bit) ....................... 19
Port Change Interrupt Enable (RBIE Bit) ................... 19
RB0/INT Enable (INTE Bit) ........................................ 19
Synchronous Serial Port (SSP) Interrupt Enable
(SSPIE Bit) ........................................................ 20
TMR0 Overflow Enable (TMR0IE Bit) ........................ 19
TMR1 Overflow Interrupt Enable (TMR1IE Bit) ......... 20
TMR2 to PR2 Match Interrupt Enable
(TMR2IE Bit) ...................................................... 20
USART Interrupt Enable (RCIE Bit) ........................... 20
USART Transmit Interrupt Enable (TXIE Bit) ............ 20
Interrupts, Flag Bits
A/D Converter Interrupt Flag (ADIF Bit) ..................... 21
CCP1 Interrupt Flag (CCP1IF Bit) ............................. 21
Comparator Interrupt Flag (CMIF Bit) ........................ 23
EEPROM Write Operation Interrupt Flag
(EEIF Bit) ........................................................... 23
Interrupt-on-Change (RB7:RB4) Flag
(RBIF Bit) ....................................................19, 140
Oscillator Fail Interrupt Flag (OSFIF Bit) ................... 23
RB0/INT Flag (INTF Bit) ............................................ 19
Synchronous Serial Port (SSP) Interrupt Flag
(SSPIF Bit) ......................................................... 21
TMR0 Overflow Flag (TMR0IF Bit) .......................... 140
TMR1 Overflow Interrupt Flag (TMR1IF Bit) .............. 21
TMR2 to PR2 Interrupt Flag (TMR2IF Bit) ................. 21
USART Receive Interrupt Flag (RCIF Bit) ................. 21
USART Transmit Interrupt Flag (TXIF Bit) ................. 21
INTRC Modes
Adjustment ................................................................. 38
L
Loading of PC .................................................................... 25
Low-Voltage ICSP Programming ..................................... 148
M
Master Clear (MCLR)
MCLR Reset, Normal Operation .......................132, 135
MCLR Reset, SLEEP ........................................132, 135
Operation and ESD Protection ................................ 133
Memory Organization ........................................................ 11
Data Memory ............................................................. 11
Program Memory ....................................................... 11
MPLAB ASM30 Assembler, Linker, Librarian .................. 158
MPLAB ICD 2 In-Circuit Debugger .................................. 159
MPLAB ICE 2000 High Performance Universal
In-Circuit Emulator ................................................... 159
MPLAB ICE 4000 High Performance Universal
In-Circuit Emulator ................................................... 159
MPLAB Integrated Development
Environment Software ............................................. 157
MPLINK Object Linker/MPLIB Object Librarian ............... 158
Preliminary
DS30487B-page 203
PIC16F87/88
O
Opcode Field Descriptions ............................................... 149
OPTION Register
INTEDG Bit ................................................................ 18
PS2:PS0 Bits .............................................................. 18
PSA Bit ....................................................................... 18
RBPU Bit .................................................................... 18
T0CS Bit ..................................................................... 18
T0SE Bit ..................................................................... 18
OSCCON Register ............................................................. 15
Oscillator Configuration ...................................................... 35
ECIO .......................................................................... 35
EXTRC ..................................................................... 134
HS ...................................................................... 35, 134
INTIO1 ........................................................................ 35
INTIO2 ........................................................................ 35
INTRC ...................................................................... 134
LP ....................................................................... 35, 134
RC ........................................................................ 35, 37
RCIO .......................................................................... 35
XT ....................................................................... 35, 134
Oscillator Control Register
Modifying IRCF Bits ................................................... 41
Clock Transition Sequence ................................ 41
Oscillator Delay upon Power-up, Wake-up and
Clock Switching .......................................................... 42
Oscillator Start-up Timer (OST) ............................... 129, 133
Oscillator Switching ............................................................ 39
OSCTUNE Register ........................................................... 15
P
Packaging Information ..................................................... 193
Marking .................................................................... 193
Paging, Program Memory .................................................. 25
PCL Register .......................................................... 14, 15, 25
PCLATH Register ................................................... 14, 15, 25
PCON Register .......................................................... 15, 134
BOR Bit ...................................................................... 24
POR Bit ...................................................................... 24
PICkit 1 FLASH Starter Kit ............................................... 161
PICSTART Plus Development Programmer .................... 159
PIE1 Register ..................................................................... 15
ADIE Bit ...................................................................... 20
CCP1IE Bit ................................................................. 20
RCIE Bit ..................................................................... 20
SSPIE Bit ................................................................... 20
TMR1IE Bit ................................................................. 20
TMR2IE Bit ................................................................. 20
TXIE Bit ...................................................................... 20
PIE2 Register ..................................................................... 15
CMIE Bit ..................................................................... 22
EEIE Bit ...................................................................... 22
OSFIE Bit ................................................................... 22
Pinout Descriptions
PIC16F87/88 ................................................................ 8
PIR1 Register ..................................................................... 14
ADIF Bit ...................................................................... 21
CCP1IF Bit ................................................................. 21
RCIF Bit ...................................................................... 21
SSPIF Bit .................................................................... 21
TMR1IF Bit ................................................................. 21
TMR2IF Bit ................................................................. 21
TXIF Bit ...................................................................... 21
DS30487B-page 204
PIR2 Register .................................................................... 14
CMIF Bit ..................................................................... 23
EEIF Bit ...................................................................... 23
OSFIF Bit ................................................................... 23
POP ................................................................................... 25
POR. See Power-on Reset.
PORTA ................................................................................ 8
Associated Register Summary .................................. 52
PORTA Register ........................................................ 14
PORTB ................................................................................ 9
Associated Register Summary .................................. 58
PORTB Register ........................................................ 14
Pull-up Enable (RBPU Bit) ......................................... 18
RB0/INT Edge Select (INTEDG Bit) .......................... 18
RB0/INT Pin, External .............................................. 140
RB2/SDO/RX/DT Pin ............................................98, 99
RB5/SS/TX/CK Pin .................................................... 98
RB7:RB4 Interrupt-on-Change ................................ 140
RB7:RB4 Interrupt-on-Change Enable
(RBIE Bit) ......................................................... 140
RB7:RB4 Interrupt-on-Change Flag
(RBIF Bit) ....................................................19, 140
TRISB Register .....................................................16, 97
PORTB Register ................................................................ 16
Postscaler, WDT
Assignment (PSA Bit) ................................................ 18
Rate Select (PS2:PS0 Bits) ....................................... 18
Power Managed Modes ..................................................... 43
RC_RUN .................................................................... 43
SEC_RUN .................................................................. 44
SEC_RUN/RC_RUN to Primary Clock Source .......... 45
Power-down Mode. See SLEEP.
Power-on Reset (POR) ............................. 129, 132, 133, 135
POR Status (POR Bit) ............................................... 24
Power Control (PCON) Register .............................. 134
Power-down (PD Bit) ............................................... 132
Time-out (TO Bit) ................................................17, 132
Power-up Timer (PWRT) ..........................................129, 133
PR2 Register ................................................................15, 79
Prescaler, Timer0
Assignment (PSA Bit) ................................................ 18
Rate Select (PS2:PS0 Bits) ....................................... 18
PRO MATE II Universal Device Programmer .................. 159
Program Counter
RESET Conditions ................................................... 135
Program Memory
Interrupt Vector .......................................................... 11
Map and Stack
PIC16F87/88 ..................................................... 11
Paging ........................................................................ 25
RESET Vector ........................................................... 11
Program Verification ........................................................ 147
PUSH ................................................................................. 25
R
R/W Bit ............................................................................... 93
RA0/AN0 Pin ........................................................................ 8
RA1/AN1 Pin ........................................................................ 8
RA2/AN2/CVREF/VREF- Pin .................................................. 8
RA3/AN3/VREF+/C1OUT Pin ............................................... 8
RA4/AN4/T0CKI/C2OUT Pin ............................................... 8
RA5/MCLR/VPP Pin ............................................................. 8
RA6/OSC2/CLKO Pin .......................................................... 8
RA7/OSC1/CLKI Pin ............................................................ 8
 2003 Microchip Technology Inc.
PIC16F87/88
RB0/INT/CCP1 Pin ............................................................... 9
RB1/SDI/SDA Pin ................................................................. 9
RB2/SDO/RX/DT Pin ........................................................... 9
RB3/PGM/CCP1 Pin ............................................................ 9
RB4/SCK/SCL Pin ................................................................ 9
RB5/SS/TX/CK Pin ............................................................... 9
RB6/AN5/PGC/T1OSO/T1CKI Pin ....................................... 9
RB7/AN6/PGD/T1OSI Pin .................................................... 9
RBIF Bit .............................................................................. 57
RCIO Oscillator .................................................................. 37
RCREG Register ................................................................ 14
RCSTA Register ................................................................. 14
ADDEN Bit ................................................................. 98
CREN Bit .................................................................... 98
FERR Bit .................................................................... 98
RX9 Bit ....................................................................... 98
RX9D Bit .................................................................... 98
SPEN Bit .............................................................. 97, 98
SREN Bit .................................................................... 98
Receive Overflow Indicator Bit, SSPOV ............................. 89
Register File ....................................................................... 12
Register File Map
PIC16F87 ................................................................... 12
PIC16F88 ................................................................... 13
Registers
ADCON0 (A/D Control 0) ......................................... 114
ADCON1 (A/D Control 1) ......................................... 115
ANSEL (Analog Select) ............................................ 113
CCP1CON (Capture/Compare/PWM
Control 1) ........................................................... 81
CMCON (Comparator Control) ................................ 121
CONFIG1 (Configuration Word 1) ............................ 130
CONFIG2 (Configuration Word 2) ............................ 131
CVRCON (Comparator Voltage
Reference Control) ........................................... 127
EECON1 (Data EEPROM Access
Control 1) ........................................................... 28
FSR ............................................................................ 26
Initialization Conditions (table) ......................... 135–136
INTCON (Interrupt Control) ........................................ 19
OPTION ..................................................................... 18
OPTION_REG ........................................................... 68
OSCCON (Oscillator Control) .................................... 40
OSCTUNE (Oscillator Tuning) ................................... 38
PCON (Power Control) .............................................. 24
PIE1 (Peripheral Interrupt Enable 1) .......................... 20
PIE2 (Peripheral Interrupt Enable 2) .......................... 22
PIR1 (Peripheral Interrupt Status 1) ........................... 21
PIR2 (Peripheral Interrupt Status 2) ........................... 23
RCSTA (Receive Status and Control) ........................ 98
Special Function, Summary ....................................... 14
SSPCON (Synchronous
Serial Port Control) ............................................ 89
SSPSTAT (Synchronous
Serial Port Status) .............................................. 88
STATUS ..................................................................... 17
T1CON (Timer1 Control) ............................................ 72
T2CON (Timer2 Control) ............................................ 80
TXSTA (Transmit Status and Control) ....................... 97
WDTCON (Watchdog Timer Control) ....................... 142
 2003 Microchip Technology Inc.
RESET ......................................................................129, 132
Brown-out Reset (BOR). See Brown-out Reset (BOR).
MCLR RESET. See MCLR.
Power-on Reset (POR). See Power-on Reset (POR).
RESET Conditions for All Registers ........................ 135
RESET Conditions for PCON Register .................... 135
RESET Conditions for Program Counter ................. 135
RESET Conditions for STATUS Register ................ 135
WDT Reset. See Watchdog Timer (WDT).
Revision History ............................................................... 199
RP0 Bit ............................................................................... 11
RP1 Bit ............................................................................... 11
S
SCI. See USART.
SCL .................................................................................... 92
Serial Communication Interface. See USART.
Slave Mode
SCL ............................................................................ 92
SDA ........................................................................... 92
SLEEP .............................................................. 129, 132, 145
Software Simulator (MPLAB SIM) ................................... 158
Software Simulator (MPLAB SIM30) ............................... 158
SPBRG Register ................................................................ 15
Special Event Trigger ...................................................... 120
Special Features of the CPU ........................................... 129
Special Function Registers ................................................ 14
Special Function Registers (SFRs) .................................... 14
SPI
Associated Registers ................................................. 90
Serial Clock ................................................................ 87
Serial Data In ............................................................. 87
Serial Data Out .......................................................... 87
Slave Select ............................................................... 87
SSP
ACK ........................................................................... 92
I2C
I2C Operation ..................................................... 92
SSPADD Register .............................................................. 15
SSPBUF Register .............................................................. 14
SSPCON Register ............................................................. 14
SSPOV .............................................................................. 89
SSPOV Bit ......................................................................... 92
SSPSTAT Register ............................................................ 15
Stack .................................................................................. 25
Overflows ................................................................... 25
Underflow .................................................................. 25
STATUS Register
C Bit ........................................................................... 17
DC Bit ........................................................................ 17
IRP Bit ....................................................................... 17
PD Bit .................................................................17, 132
RP Bit ........................................................................ 17
TO Bit .................................................................17, 132
Z Bit ........................................................................... 17
Synchronous Master Reception
Associated Registers ............................................... 110
Synchronous Master Transmission
Associated Registers ............................................... 109
Synchronous Serial Port (SSP) ......................................... 87
Overview .................................................................... 87
SPI Mode ................................................................... 87
Synchronous Slave Reception
Associated Registers ............................................... 112
Synchronous Slave Transmission
Associated Registers ............................................... 111
Preliminary
DS30487B-page 205
P
I C
1 6 F
8 7 / 8 8
T
T1CKPS0 Bit ...................................................................... 72
T1CKPS1 Bit ...................................................................... 72
T1CON Register ................................................................. 14
T1OSCEN Bit ..................................................................... 72
T1SYNC Bit ........................................................................ 72
T2CKPS0 Bit ...................................................................... 80
T2CKPS1 Bit ...................................................................... 80
T2CON Register ................................................................. 14
TAD ................................................................................... 118
Time-out Sequence .......................................................... 134
Timer0 ................................................................................ 67
Associated Registers ................................................. 69
Clock Source Edge Select (T0SE Bit) ........................ 18
Clock Source Select (T0CS Bit) ................................. 18
External Clock ............................................................ 68
Interrupt ...................................................................... 67
Operation ................................................................... 67
Overflow Enable (TMR0IE Bit) ................................... 19
Overflow Flag (TMR0IF Bit) ..................................... 140
Overflow Interrupt ..................................................... 140
Prescaler .................................................................... 68
T0CKI ......................................................................... 68
Timer1 ................................................................................ 71
Associated Registers ................................................. 77
Asynchronous Counter Mode ..................................... 74
Reading and Writing .......................................... 74
Capacitor Selection .................................................... 75
Counter Operation ...................................................... 73
Operation ................................................................... 71
Operation in Timer Mode ........................................... 73
Oscillator .................................................................... 75
Oscillator Layout Considerations ............................... 75
Prescaler .................................................................... 76
Resetting Timer1 Register Pair .................................. 76
Resetting Timer1 Using a CCP Trigger Output .......... 75
Synchronized Counter Mode ...................................... 73
Use as a Real-Time Clock ......................................... 76
Timer2 ................................................................................ 79
Associated Registers ................................................. 80
Output ........................................................................ 79
Postscaler .................................................................. 79
Prescaler .................................................................... 79
Prescaler and Postscaler ........................................... 79
Timing Diagrams
A/D Conversion ........................................................ 189
Asynchronous Master Transmission ........................ 103
Asynchronous Master Transmission
(Back to Back) .................................................. 103
Asynchronous Reception ......................................... 104
Asynchronous Reception with
Address Byte First ............................................ 107
Asynchronous Reception with Address Detect ........ 107
Brown-out Reset ...................................................... 179
Capture/Compare/PWM (CCP1) .............................. 181
CLKO and I/O ........................................................... 178
External Clock .......................................................... 177
Fail-Safe Clock Monitor ............................................ 144
I2C Bus Data ............................................................ 185
I2C Bus START/STOP Bits ...................................... 184
I2C Reception (7-bit Address) .................................... 94
I2C Transmission (7-bit Address) ............................... 94
Primary System Clock after RESET
(EC, RC, INTRC) ............................................... 48
DS30487B-page 206
Primary System Clock after RESET (HS, XT, LP) ..... 47
PWM Output .............................................................. 84
RESET, Watchdog Timer, Oscillator Start-up
Timer and Power-up Timer .............................. 179
Slow Rise Time (MCLR Tied to VDD
Through RC Network) ...................................... 138
SPI Master Mode ....................................................... 91
SPI Master Mode (CKE = 0, SMP = 0) .................... 182
SPI Master Mode (CKE = 1, SMP = 1) .................... 182
SPI Slave Mode (CKE = 0) .................................91, 183
SPI Slave Mode (CKE = 1) .................................91, 183
Switching to SEC_RUN Mode ................................... 44
Synchronous Reception (Master Mode, SREN) ...... 111
Synchronous Transmission ..................................... 109
Synchronous Transmission (Through TXEN) .......... 109
Time-out Sequence on Power-up (MCLR Tied
to VDD Through Pull-up Resistor) .................... 137
Time-out Sequence on Power-up (MCLR Tied
to VDD Through RC Network): Case 1 ............. 137
Time-out Sequence on Power-up (MCLR Tied
to VDD Through RC Network): Case 2 ............. 137
Timer0 and Timer1 External Clock .......................... 180
Timer1 Incrementing Edge ........................................ 73
Transition Between SEC_RUN/RC_RUN
and Primary Clock ............................................. 46
Two-Speed Start-up Mode ....................................... 143
USART Synchronous Receive (Master/Slave) ........ 187
USART Synchronous Transmission
(Master/Slave) ................................................. 187
Wake-up from SLEEP via Interrupt .......................... 146
XT, HS, LP, EC and EXTRC to RC_RUN Mode ........ 43
Timing Parameter Symbology .......................................... 176
Timing Requirements
A/D Conversion ........................................................ 189
Capture/Compare/PWM (CCP1) ............................. 181
CLKO and I/O .......................................................... 178
External Clock .......................................................... 177
I2C Bus Data ............................................................ 186
I2C Bus START/STOP Bits ...................................... 185
RESET, Watchdog Timer, Oscillator
Start-up Timer, Power-up Timer and
Brown-out Reset .............................................. 179
SPI Mode ................................................................. 184
Timer0 and Timer1 External Clock .......................... 180
USART Synchronous Receive ................................. 187
USART Synchronous Transmission ........................ 187
TMR0 Register ................................................................... 14
TMR1CS Bit ....................................................................... 72
TMR1H Register ................................................................ 14
TMR1L Register ................................................................. 14
TMR1ON Bit ....................................................................... 72
TMR2 Register ................................................................... 14
TMR2ON Bit ....................................................................... 80
TMRO Register .................................................................. 16
TOUTPS0 Bit ..................................................................... 80
TOUTPS1 Bit ..................................................................... 80
TOUTPS2 Bit ..................................................................... 80
TOUTPS3 Bit ..................................................................... 80
TRISA Register .............................................................15, 51
TRISB Register .................................................................. 15
Two-Speed Clock Start-up Mode ..................................... 143
Two-Speed Start-up ......................................................... 129
TXREG Register ................................................................ 14
 2003 Microchip Technology Inc.
PIC16F87/88
TXSTA Register ................................................................. 15
BRGH Bit ................................................................... 97
CSRC Bit .................................................................... 97
SYNC Bit .................................................................... 97
TRMT Bit .................................................................... 97
TX9 Bit ....................................................................... 97
TX9D Bit ..................................................................... 97
TXEN Bit .................................................................... 97
U
USART ............................................................................... 97
Address Detect Enable (ADDEN Bit) ......................... 98
Asynchronous Mode ................................................ 102
Asynchronous Receive (9-bit Mode) ........................ 106
Asynchronous Receive with Address Detect.
See Asynchronous Receive (9-bit Mode).
Asynchronous Receiver ........................................... 104
Asynchronous Reception ......................................... 105
Asynchronous Transmitter ....................................... 102
Baud Rate Generator (BRG) ...................................... 99
Baud Rate Formula ............................................ 99
Baud Rates, Asynchronous Mode
(BRGH = 0) .............................................. 100
Baud Rates, Asynchronous Mode
(BRGH = 1) .............................................. 100
High Baud Rate Select (BRGH Bit) .................... 97
INTRC Baud Rates, Asynchronous Mode
(BRGH = 0) .............................................. 101
INTRC Baud Rates, Asynchronous Mode
(BRGH = 1) .............................................. 101
INTRC Operation ............................................... 99
Low-power Mode Operation ............................... 99
Sampling ............................................................ 99
Clock Source Select (CSRC Bit) ................................ 97
Continuous Receive Enable (CREN Bit) .................... 98
Framing Error (FERR Bit) .......................................... 98
Mode Select (SYNC Bit) ............................................ 97
Receive Data, 9th bit (RX9D Bit) ............................... 98
Receive Enable, 9-bit (RX9 Bit) ................................. 98
Serial Port Enable (SPEN Bit) .............................. 97, 98
Single Receive Enable (SREN Bit) ............................ 98
Synchronous Master Mode ...................................... 108
Synchronous Master Reception ............................... 110
Synchronous Master Transmission .......................... 108
Synchronous Slave Mode ........................................ 111
Synchronous Slave Reception ................................. 112
Synchronous Slave Transmit ................................... 111
Transmit Data, 9th Bit (TX9D) .................................... 97
Transmit Enable (TXEN Bit) ....................................... 97
Transmit Enable, Nine-bit (TX9 Bit) ........................... 97
Transmit Shift Register Status (TRMT Bit) ................. 97
USART Synchronous Receive Requirements .................. 187
 2003 Microchip Technology Inc.
V
VDD Pin ................................................................................ 9
Voltage Reference Specifications .................................... 175
VSS Pin ................................................................................ 9
W
Wake-up from SLEEP ...............................................129, 146
Interrupts ................................................................. 135
MCLR Reset ............................................................ 135
WDT Reset .............................................................. 135
Wake-up Using Interrupts ................................................ 146
Watchdog Timer (WDT) ............................................129, 141
Associated Registers ............................................... 142
WDT Reset, Normal Operation .........................132, 135
WDT Reset, SLEEP ..........................................132, 135
WCOL ................................................................................ 89
WDTCON Register ............................................................ 16
Write Collision Detect Bit, WCOL ...................................... 89
WWW, On-Line Support ...................................................... 4
Preliminary
DS30487B-page 207
PIC16F87/88
NOTES:
DS30487B-page 208
 2003 Microchip Technology Inc.
PIC16F87/88
ON-LINE SUPPORT
Microchip provides on-line support on the Microchip
World Wide Web site.
The web site is used by Microchip as a means to make
files and information easily available to customers. To
view the site, the user must have access to the Internet
and a web browser, such as Netscape® or Microsoft®
Internet Explorer. Files are also available for FTP
download from our FTP site.
SYSTEMS INFORMATION AND
UPGRADE HOT LINE
The Systems Information and Upgrade Line provides
system users a listing of the latest versions of all of
Microchip's development systems software products.
Plus, this line provides information on how customers
can receive the most current upgrade kits. The Hot Line
Numbers are:
1-800-755-2345 for U.S. and most of Canada, and
1-480-792-7302 for the rest of the world.
Connecting to the Microchip Internet
Web Site
042003
The Microchip web site is available at the following
URL:
www.microchip.com
The file transfer site is available by using an FTP
service to connect to:
ftp://ftp.microchip.com
The web site and file transfer site provide a variety of
services. Users may download files for the latest
Development Tools, Data Sheets, Application Notes,
User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also
available, including listings of Microchip sales offices,
distributors and factory representatives. Other data
available for consideration is:
• Latest Microchip Press Releases
• Technical Support Section with Frequently Asked
Questions
• Design Tips
• Device Errata
• Job Postings
• Microchip Consultant Program Member Listing
• Links to other useful web sites related to
Microchip Products
• Conferences for products, Development Systems,
technical information and more
• Listing of seminars and events
 2003 Microchip Technology Inc.
Preliminary
DS30487B-page 209
PIC16F87/88
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Device: PIC16F87/88
Y
N
Literature Number: DS30487B
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS30487B-page 210
Preliminary
 2003 Microchip Technology Inc.
PIC16F87/88
PIC16F87/88 PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
Temperature
Range
/XX
XXX
Package
Pattern
Examples:
a)
b)
Device
PIC16F87: Standard VDD range
PIC16F87T: (Tape and Reel)
PIC16LF87: Extended VDD range
Temperature Range
I
Package
P
SO
SS
ML
=
=
PIC16F87-I/P = Industrial temp., PDIP
package, Extended VDD limits.
PIC16F87-I/SO = Industrial temp., SOIC
package, normal VDD limits.
0°C to +70°C
-40°C to +85°C
=
=
=
=
PDIP
SOIC
SSOP
QFN
Note 1:
Pattern
QTP, SQTP, ROM Code (factory specified) or
Special Requirements. Blank for OTP and
Windowed devices.
 2003 Microchip Technology Inc.
Preliminary
2:
F = CMOS FLASH
LF = Low-power CMOS FLASH
T = in tape and reel - SOIC, SSOP
packages only.
DS30487B-page 211
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
Korea
Corporate Office
Australia
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support: 480-792-7627
Web Address: http://www.microchip.com
Suite 22, 41 Rawson Street
Epping 2121, NSW
Australia
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea 135-882
Tel: 82-2-554-7200 Fax: 82-2-558-5932 or
82-2-558-5934
Atlanta
Unit 915
Bei Hai Wan Tai Bldg.
No. 6 Chaoyangmen Beidajie
Beijing, 100027, No. China
Tel: 86-10-85282100
Fax: 86-10-85282104
3780 Mansell Road, Suite 130
Alpharetta, GA 30022
Tel: 770-640-0034
Fax: 770-640-0307
Boston
2 Lan Drive, Suite 120
Westford, MA 01886
Tel: 978-692-3848
Fax: 978-692-3821
Chicago
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160
Addison, TX 75001
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
2767 S. Albright Road
Kokomo, IN 46902
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
China - Beijing
China - Chengdu
Rm. 2401-2402, 24th Floor,
Ming Xing Financial Tower
No. 88 TIDU Street
Chengdu 610016, China
Tel: 86-28-86766200
Fax: 86-28-86766599
China - Fuzhou
Unit 28F, World Trade Plaza
No. 71 Wusi Road
Fuzhou 350001, China
Tel: 86-591-7503506
Fax: 86-591-7503521
China - Hong Kong SAR
Unit 901-6, Tower 2, Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Shanghai
Room 701, Bldg. B
Far East International Plaza
No. 317 Xian Xia Road
Shanghai, 200051
Tel: 86-21-6275-5700
Fax: 86-21-6275-5060
China - Shenzhen
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888
Fax: 949-263-1338
Rm. 1812, 18/F, Building A, United Plaza
No. 5022 Binhe Road, Futian District
Shenzhen 518033, China
Tel: 86-755-82901380
Fax: 86-755-8295-1393
Phoenix
China - Shunde
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7966
Fax: 480-792-4338
Room 401, Hongjian Building
No. 2 Fengxiangnan Road, Ronggui Town
Shunde City, Guangdong 528303, China
Tel: 86-765-8395507 Fax: 86-765-8395571
San Jose
China - Qingdao
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950
Fax: 408-436-7955
Rm. B505A, Fullhope Plaza,
No. 12 Hong Kong Central Rd.
Qingdao 266071, China
Tel: 86-532-5027355 Fax: 86-532-5027205
Toronto
India
6285 Northam Drive, Suite 108
Mississauga, Ontario L4V 1X5, Canada
Tel: 905-673-0699
Fax: 905-673-6509
Divyasree Chambers
1 Floor, Wing A (A3/A4)
No. 11, O’Shaugnessey Road
Bangalore, 560 025, India
Tel: 91-80-2290061 Fax: 91-80-2290062
Japan
Benex S-1 6F
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa, 222-0033, Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
DS30487B-page 212
Preliminary
Singapore
200 Middle Road
#07-02 Prime Centre
Singapore, 188980
Tel: 65-6334-8870 Fax: 65-6334-8850
Taiwan
Kaohsiung Branch
30F - 1 No. 8
Min Chuan 2nd Road
Kaohsiung 806, Taiwan
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan
Taiwan Branch
11F-3, No. 207
Tung Hua North Road
Taipei, 105, Taiwan
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
EUROPE
Austria
Durisolstrasse 2
A-4600 Wels
Austria
Tel: 43-7242-2244-399
Fax: 43-7242-2244-393
Denmark
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45-4420-9895 Fax: 45-4420-9910
France
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany
Steinheilstrasse 10
D-85737 Ismaning, Germany
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy
Via Quasimodo, 12
20025 Legnano (MI)
Milan, Italy
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands
P. A. De Biesbosch 14
NL-5152 SC Drunen, Netherlands
Tel: 31-416-690399
Fax: 31-416-690340
United Kingdom
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44-118-921-5869
Fax: 44-118-921-5820
07/28/03
 2003 Microchip Technology Inc.