COMMUNICATIONS MODULES & SUBSYSTEMS WaveReady™ WRA-110, WRA-113, WRA-116, WRA-119 Single-channel, Erbium-doped Fiber Amplifiers Key Features • Protocol and data-rate independent, including 10 Gbps/ OC-192 applications • Easily configurable as a booster or a pre/inline C-band amplifier • Four variants WRA-110, WRA-113, WRA-116, WRA-119 to match specific application requirements • Constant signal gain mode configurable to 13 dB (WRA-110) and to 26 dB (WRA-119) • Constant total output power mode configurable to 10 dBm (WRA-110) and to 19 dBm (WRA-119) • Low power consumption and noise figure Applications • Serves as a booster or pre/inline amplifier • Use for Access and Metro optical networks • Works with point-to-point applications Compliance • Telcordia NEBS Level 3 • FDA Class 1M laser device • FCC Class A device • UL 60950-1 First Edition • CAN/CSA C22.2 No. 60950 01 • CE • IEC 60825-2 • RoHS (exemptions 7b, 8a) NORTH AMERICA : 800 498-JDSU (5378) The WaveReady WRA-1xx series are user-configurable, single-channel optical amplifiers that provide simple and economical C-band optical amplification for single-channel applications in a flexible, ready-to-use package. These erbiumdoped fiber amplifiers (EDFAs) are network-ready and easily configured as a booster or as a pre/inline amplifier. The modules work by default in constant signal-gain mode, but they can be configured to constant total output-power mode. Its ease-of-use and performance make the WRA-1xx series the ideal solution for Access and Metro optical networks. Front-panel light emitting diodes (LEDs) indicate module status, while integrated electronics provide alarm and control functionality. Deployed with a WaveReady communications module (COM200), these units can be managed and configured remotely through TL1, SNMP, or by using the WaveReady Node Manager. Local and remote management is performed through an RS232 or Ethernet port on the communications module. The module can be installed in a WaveReady 3500F or 3100 shelf mounted in 19or 23-inch telecommunications racks. WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com/waveready WRA-110, WRA-113, WRA-116, WRA-119 2 Amplification for Extended Reach and Pre-amp Application Minimum Power Total Power Budget Maximum Rx Distance 49 dB 200 km –30 dBm WRA-113 Power Mask 25 25 20 20 15 NF = 6.4 dB 10 NF = 8.5 dB 5 0 -5 NF = 7.5dB -10 NF = 6.2 dB -15 Output Power (dBm) Output Power (dBm) WRA-110 Power Mask 15 NF = 5.5 dB 5 NF = 8.5dB 0 -5 NF = 7.5dB -10 NF = 6.2 dB -15 -20 -20 -35 -30 -25 -20 -15 -10 -5 0 -35 5 -30 -25 Figure 1: Power mask with noise figures1 for WRA-110 25 NF = 5.3 dB 15 NF = 8.5dB 10 5 NF = 6.5dB NF = 7.5dB -10 NF = 6.2dB -15 -5 NF = 5.5dB 20 NF = 6.3 dB Output Power (dBm) Output Power (dBm) 20 -10 0 5 WRA-119 Power Mask 25 0 -15 Figure 2: Power mask with noise figures for WRA-113 WRA-116 Power Mask -5 -20 Input Power (dBm) Input Power (dBm) NF = 6.0dB 15 NF = 8.5dB 10 5 0 -5 NF = 6.5dB NF = 7.5dB -10 NF = 6.2dB -15 -20 -20 -35 -30 -25 -20 -15 -10 Input Power (dBm) Figure 3: Power mask with noise figures for WRA-116 1 NF = 7.3 dB 10 Noise figures are maximum, EOL values. -5 0 5 -35 -30 -25 -20 -15 -10 Input Power (dBm) Figure 4: Power mask with noise figures for WRA-119 -5 0 5 WRA-110, WRA-113, WRA-116, WRA-119 3 Specifications Optical Performance1 Parameter Operating wavelength range Input power range WRA-110 WRA-113 WRA-116 WRA-119 Total output power (User configurable in constant Pout mode; 0.1 dB set resolution) WRA-110 WRA-113 WRA-116 WRA-119 Input LOS threshold configurable range (User configurable; 1.0 dB set resolution) Power measurement accuracy (all detectors) P ≥ –29 dBm –29 < P ≤ –38 dBm Gain (User configurable in constant gain mode; 0.1 dB set resolution) WRA-110 WRA-113 WRA-116 WRA-119 Polarization dependent gain Gain accuracy (Relative to gain target, in constant gain mode) Gain stability (Peak-to-peak, in constant gain mode) Noise figures Polarization mode dispersion Remnant 980 to output Return loss Minimum 1530 nm Typical — Maximum 1563 nm –23 dBm –29 dBm –30 dBm –30 dBm — — — — +3 dBm +3 dBm +3 dBm +3 dBm –10 dBm –10 dBm –10 dBm –10 dBm –38 dBm — — — — — +10 dBm +13 dBm +16 dBm +19 dBm 0 dBm –0.7 dB –1.5 dB 7 dB 7 dB 7 dB 7 dB 7 dB — –1.25 dB –0.1 dB — — — — — — — — — — see Figures 1, 2, 3, and 4 — — — +0.7 dB +1.5 dB 26 dB 13 dB 19 dB 26 dB 26 dB 0.3 dB +1.25 dB 0.1 dB — — –40 dB 0.5 ps –30 dBm — Electrical Specifications2 Parameter DC supply voltage Power dissipation Alarm relay signals 1 Minimum Typical Maximum — –48 V — — 12 W 17 W Dry contact major and minor alarms. Relay open under normal operation. Relay closed when power is off. Unless otherwise stated, all specifications are end-of-life, across all temperature and input conditions. Electrical specifications assume installation in a WaveReady 3500F or 3100 shelf (DMS-3500FSE03 or DMS-3100DC004). 2 WRA-110, WRA-113, WRA-116, WRA-119 Specifications Physical Specifications Parameter Size (H x W x D) Weight (approximate) Typical 17.27 x 2.54 x 22.35 cm (6.8 x 1.0 x 8.8 in) 0.73 kg (1.6 lb) Environmental Specifications Parameter Normal operating temperature Extended operating temperature Storage temperature Relative humidity (non-condensing) Minimum 0°C –5°C –40°C 5% Typical — — — — Maximum 40°C 55°C 85°C 90% Interface Specifications Interface Optical Craft TL1/SNMP Front panel Description LC/UPC SMF Requires WaveReady 3100 or 3500F series shelf and a WaveReady COM200 communications module. Craft access through RS232/DB-9 connector on front panel of COM200 module. Requires WaveReady 3500F or 3100 series shelf and a WaveReady COM200 communications module. TL1/SNMP interfaces via the 10/100BaseT Ethernet/RJ45 connector on the front panel of a COM200. Six LEDs: CARD (power); MAJ/CRIT (major/critical alarm); MIN (minor alarm);TX and RX (port status), Laser On Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at [email protected]. Product Code WRA-110 WRA-113 WRA-116 WRA-119 Associated Parts DMS-3100DC004 DMS-3500FSE03 COM-200ET003Y NORTH AMERICA : 800 498-JDSU (5378) Description Single-channel EDFA, 10 dBm output Single-channel EDFA, 13 dBm output Single-channel EDFA, 16 dBm output Single-channel EDFA, 19 dBm output WR3100 1U Shelf WR3500F Shelf COM200 Communication module WORLDWIDE : +800 5378-JDSU Product specifications and descriptions in this document subject to change without notice. © 2009 JDS Uniphase Corporation WEBSITE : www.jdsu.com/waveready 30149178 001 0109 WRA1XX.DS.CMS.AE January 2009